U-boot debug with BDI3000
Hi,
Does anyone have a working BDI2000/3000 configuration for CN5010 dev.board? I need it to have DDR and NOR flash support so that I can flash a new bootloader into NOR.
Thanks!
Shuyou
Dear sywang,
Am 07.10.2010 um 09:49 schrieb sywang:
Quoted 3 lines
Hi,
Does anyone have a working BDI2000/3000 configuration for CN5010 dev.board?
Yes I have one, but not on-hand currently. Will have a look for it tomorrow or on monday.
Quoted 2 lines
I need it to have DDR and NOR flash support so that I can flash a new bootloader into NOR.
AFAIR it is enough to setup bootbus for correct sizes. TLB is not necessary to get access to NOR cause this is already setup by reset. It is not as fast as it could be but you have at least access to NOR and erase/prog works.
regards
Andreas Bie?mann
Andreas,
Thanks for your help. When you have it, please send an email with the configuration file to me.
Thanks!
Shuyou
-----Original Message-----
From: Andreas Bie?mann [mailto:andreas.devel at googlemail.com]
Sent: 2010?10?8? 0:14
To: sywang
Cc: u-boot at lists.denx.de
Subject: Re: [U-Boot] U-boot debug with BDI3000
Dear sywang,
Am 07.10.2010 um 09:49 schrieb sywang:
Quoted 3 lines
Hi,
Does anyone have a working BDI2000/3000 configuration for CN5010
dev.board?
Yes I have one, but not on-hand currently. Will have a look for it tomorrow or on monday.
Quoted 2 lines
I need it to have DDR and NOR flash support so that I can flash a new bootloader into NOR.
AFAIR it is enough to setup bootbus for correct sizes. TLB is not necessary to get access to NOR cause this is already setup by reset. It is not as fast as it could be but you have at least access to NOR and erase/prog works.
regards
Andreas Bie?mann
[U-Boot] warning: GDB can't find the start of the function at 0x1fc0003c.
While debugging u-boot by BDI3000 and GDB, I have the following issue. Do you encounter such a problem? How to fix it? Any suggestions are warmly welcome?
(gbd) n
[wangsy at localhost u-boot]$ /home/wangsy/gdb-mips/bin/mips-linux-gdb u-boot-octeon_bbgw_ref_failsafe
GNU gdb (GDB) 7.2
Copyright (C) 2010 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later
<http://gnu.org/licenses/gpl.html>
This is free software: you are free to change and redistribute it. There is NO WARRANTY, to the extent permitted by law. Type "show copying" and "show warranty" for details.
This GDB was configured as "--host=i686-pc-linux-gnu --target=mips-linux". For bug reporting instructions, please see:
<http://www.gnu.org/software/gdb/bugs/>...
Reading symbols from /home/wangsy/uboot_porting/OCTEON-SDK_1008_ago/bootloader/u-boot/u-boot-octe on_bbgw_ref_failsafe...done.
(gdb) target extended-remote 192.168.5.20:2001
Remote debugging using 192.168.5.20:20010x1fc0003c in ?? ()
(gdb) n
warning: GDB can't find the start of the function at 0x1fc0003c.
GDB is unable to find the start of the function at 0x1fc0003c
and thus can't determine the size of that function's stack frame. This means that GDB may be unable to access that stack frame, or the frames below it.
This problem is most likely caused by an invalid program counter or
stack pointer.
However, if you think GDB should simply search farther back
from 0x1fc0003c for code which looks like the beginning of a function, you can increase the range of the search using the `set heuristic-fence-post' command.
Cannot find bounds of current function
(gdb) set heuristic-fence-post 0
(gdb) n
warning: GDB can't find the start of the function at 0x1fc0003c. Cannot find bounds of current function
(gdb) n
Cannot find bounds of current function
(gdb) n
Cannot find bounds of current function
Thanks!
Shuyou