Skip to contentSkip to conversation

S3C24xx: Enable only the clocks of used units

RFC In review Juergen Beisert 2 participants 4 messages Oct 18, 2010 – Oct 19, 2010

Subsystems (6)
lore
Share & tools
lore
#0 lore raw

RFC 1/1 S3C24xx: Enable only the clocks of used units

From: Juergen Beisert <[email protected]>
Subject: [RFC] S3C24xx: Enable only the clocks of used units

This patch disables most of the processor's clocks and enable them on demand only.

---
 arch/arm/mach-s3c24xx/generic.c                     |   22 +++++++++
 arch/arm/mach-s3c24xx/include/mach/s3c24x0-clocks.h |   46 ++++++++++++++++++++
 arch/arm/mach-s3c24xx/lowlevel-init.S               |   12 ++++-
 drivers/mtd/nand/nand_s3c2410.c                     |    3 +
 drivers/serial/serial_s3c24x0.c                     |    3 +
 5 files changed, 84 insertions(+), 2 deletions(-)
arch/arm/mach-s3c24xx/generic.c +22 -0
Index: barebox-2010.10.0/arch/arm/mach-s3c24xx/generic.c
===================================================================
@@ -28,6 +28,7 @@
 #include <clock.h>
 #include <asm/io.h>
 #include <mach/s3c24x0-iomap.h>
+#include <mach/s3c24x0-clocks.h>
 
 #define LOCKTIME (S3C24X0_CLOCK_POWER_BASE)
 #define MPLLCON (S3C24X0_CLOCK_POWER_BASE + 0x4)
@@ -202,6 +203,25 @@ unsigned s3c24x0_get_memory_size(void)
 }
 
 /**
+ * Enable or disable unit's clock
+ * @param unit Unit to manipulate (refer CLK_* macros)
+ * @param state 1 for enable, 0 for disable
+ */
+void s3c244x_mod_clock(unsigned unit, int state)
+{
+	uint32_t clkcon;
+
+	clkcon = readl(CLKCON);
+
+	if (state != 0)
+		clkcon |= unit;
+	else
+		clkcon &= ~unit;
+
+	writel(clkcon, CLKCON);
+}
+
+/**
  * Show the user the current clock settings
  */
 int s3c24xx_dump_clocks(void)
@@ -236,6 +256,8 @@ static int clocksource_init (void)
 {
 	unsigned p_clk = s3c24xx_get_pclk();
 
+	s3c244x_mod_clock(CLK_PWMTIMER, 1);
+
 	writel(0x00000000, TCON);	/* stop all timers */
 	writel(0x00ffffff, TCFG0);	/* PCLK / (255 + 1) for timer 4 */
 	writel(0x00030000, TCFG1);	/* /16 */
arch/arm/mach-s3c24xx/include/mach/s3c24x0-clocks.h new file +46 -0

46 lines not on this page · raw message

arch/arm/mach-s3c24xx/lowlevel-init.S +10 -2
Index: barebox-2010.10.0/arch/arm/mach-s3c24xx/lowlevel-init.S
===================================================================
@@ -20,6 +20,7 @@
 
 #include <config.h>
 #include <mach/s3c24x0-iomap.h>
+#include <mach/s3c24x0-clocks.h>
 
 	.section ".text_bare_init.s3c24x0_disable_wd","ax"
 
@@ -83,8 +84,15 @@ s3c24x0_pll_init:
 	mov r1, #BOARD_SPECIFIC_CLKDIVN
 	str r1, [r0, #20]
 
-	/* enable all devices on this chip */
-	mov r1, #0xFFFFFFF0
+	/*
+	 * Disable the clocks for most devices on this chip.
+	 * They will be enabled again on demand
+	 */
+#ifdef CONFIG_S3C24XX_NAND_BOOT
+	ldr r1, =0x6010 /* (CLK_RTC | CLK_GPIO | CLK_NAND) */
+#else
+	mov r1, #0x6000 /* (CLK_RTC | CLK_GPIO) */
+#endif
 	str r1, [r0, #12]
 
 	/* ??????? */
drivers/mtd/nand/nand_s3c2410.c +3 -0
Index: barebox-2010.10.0/drivers/mtd/nand/nand_s3c2410.c
===================================================================
@@ -32,6 +32,7 @@
 #include <linux/mtd/nand.h>
 #include <mach/s3c24xx-generic.h>
 #include <mach/s3c24x0-iomap.h>
+#include <mach/s3c24x0-clocks.h>
 #include <mach/s3c24x0-nand.h>
 #include <asm/io.h>
 #include <asm-generic/errno.h>
@@ -358,6 +359,8 @@ static int s3c24x0_nand_probe(struct dev
 	if (!host)
 		return -ENOMEM;
 
+	s3c244x_mod_clock(CLK_NAND, 1);
+
 	host->dev = dev;
 	host->base = dev->map_base;
 
drivers/serial/serial_s3c24x0.c +3 -0
Index: barebox-2010.10.0/drivers/serial/serial_s3c24x0.c
===================================================================
@@ -27,6 +27,7 @@
 #include <asm/io.h>
 #include <mach/s3c24xx-generic.h>
 #include <mach/s3c24x0-iomap.h>
+#include <mach/s3c24x0-clocks.h>
 
 /* Note: Offsets are for little endian access */
 #define ULCON 0x00		/* line control */
@@ -123,6 +124,8 @@ static int s3c24x0_serial_probe(struct d
 
 	cdev = malloc(sizeof(struct console_device));
 
+	s3c244x_mod_clock(CLK_UART0 | CLK_UART1 | CLK_UART2, 1);
+
 	dev->type_data = cdev;
 	cdev->dev = dev;
 	cdev->f_caps = CONSOLE_STDIN | CONSOLE_STDOUT | CONSOLE_STDERR;

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox

#1 lore raw

arch/arm/mach-s3c24xx/lowlevel-init.S s3c24x0_pll_init: · line 94

Quoted 9 lines
arch/arm/mach-s3c24xx/lowlevel-init.S +8 -1
-	mov r1, #0xFFFFFFF0
+	/*
+	 * Disable the clocks for most devices on this chip.
+	 * They will be enabled again on demand
+	 */
+#ifdef CONFIG_S3C24XX_NAND_BOOT
+	ldr r1, =0x6010 /* (CLK_RTC | CLK_GPIO | CLK_NAND) */
+#else
+	mov r1, #0x6000 /* (CLK_RTC | CLK_GPIO) */

how about use the macro and define a macro to avoid the ifdef

Best Regards,
J.

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox

#2 lore raw
Quoted 11 lines · Jean-Christophe PLAGNIOL-VILLARD

arch/arm/mach-s3c24xx/lowlevel-init.S s3c24x0_pll_init: · line 94

Quoted 9 lines
arch/arm/mach-s3c24xx/lowlevel-init.S +8 -1
-	mov r1, #0xFFFFFFF0
+	/*
+	 * Disable the clocks for most devices on this chip.
+	 * They will be enabled again on demand
+	 */
+#ifdef CONFIG_S3C24XX_NAND_BOOT
+	ldr r1, =0x6010 /* (CLK_RTC | CLK_GPIO | CLK_NAND) */
+#else
+	mov r1, #0x6000 /* (CLK_RTC | CLK_GPIO) */

how about use the macro and define a macro to avoid the ifdef

I tried with macros, but the assembler failed. Can't remember why. But I tried again a few minutes ago .... and now it works (????).

Do you mean something like this instead?

[...]
#ifdef CONFIG_S3C24XX_NAND_BOOT

# define FORCED_CLOCKS (CLK_RTC | CLK_GPIO | CLK_NAND)
#else
# define FORCED_CLOCKS (CLK_RTC | CLK_GPIO)
#endif

/*
* Disable the clocks for most devices on this chip.
* They will be enabled again on demand
*/
ldr r1, =FORCED_CLOCKS
[...]

jbe

Signature · 9 lines
Pengutronix e.K.                              | Juergen Beisert             |
Linux Solutions for Science and Industry      | Phone: +49-8766-939 228     |
Vertretung Sued/Muenchen, Germany             | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686              | http://www.pengutronix.de/  |

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#3 lore raw
Quoted 13 lines · Juergen Beisert
Quoted 11 lines · Jean-Christophe PLAGNIOL-VILLARD

arch/arm/mach-s3c24xx/lowlevel-init.S s3c24x0_pll_init: · line 94

Quoted 9 lines
arch/arm/mach-s3c24xx/lowlevel-init.S +8 -1
-	mov r1, #0xFFFFFFF0
+	/*
+	 * Disable the clocks for most devices on this chip.
+	 * They will be enabled again on demand
+	 */
+#ifdef CONFIG_S3C24XX_NAND_BOOT
+	ldr r1, =0x6010 /* (CLK_RTC | CLK_GPIO | CLK_NAND) */
+#else
+	mov r1, #0x6000 /* (CLK_RTC | CLK_GPIO) */

how about use the macro and define a macro to avoid the ifdef

Quoted 2 lines

I tried with macros, but the assembler failed. Can't remember why. But I tried again a few minutes ago .... and now it works (????).

make because you had c definition in the header?

Quoted 10 lines

Do you mean something like this instead?

[...]
#ifdef CONFIG_S3C24XX_NAND_BOOT

# define FORCED_CLOCKS (CLK_RTC | CLK_GPIO | CLK_NAND)
#else
# define FORCED_CLOCKS (CLK_RTC | CLK_GPIO)
#endif
Quoted 5 lines

/*
* Disable the clocks for most devices on this chip.
* They will be enabled again on demand
*/
ldr r1, =FORCED_CLOCKS

yeah excalty

Best Regards,
J.

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox