Add GPIO WP and HW bus-width caps when support i.MX51 BBG board
Subsystems (6)
cover Add GPIO WP and HW bus-width caps when support i.MX51 BBG board
This serial patches are based on Wolfram and Eric's eSDHC driver patchs, and add the GPIO Write Protection, and HW bus-width cpas supports on i.MX51 BBG boards.
[PATCH 1/2] Add the GPIO Write Protection Solution on i.MX51 BBG boardarch/arm/mach-mx5/board-mx51_babbage.c | 16 ++++++++++++++--arch/arm/plat-mxc/include/mach/iomux-mx51.h | 8 +++++---
2 files changed, 19 insertions(+), 5 deletions(-)
[PATCH 2/2] Add the HW board caps flag for MX51 BBG
arch/arm/mach-mx5/board-mx51_babbage.c | 3 +++ arch/arm/plat-mxc/include/mach/esdhc.h | 1 + drivers/mmc/host/sdhci-esdhc-imx.c | 1 + drivers/mmc/host/sdhci.c | 8 ++++++-- 4 files changed, 11 insertions(+), 2 deletions(-)
PATCH 1/2 Add the GPIO Write Protection Solution on i.MX51 BBG board
--- arch/arm/mach-mx5/board-mx51_babbage.c | 16 ++++++++++++++-- arch/arm/plat-mxc/include/mach/iomux-mx51.h | 8 +++++--- 2 files changed, 19 insertions(+), 5 deletions(-)
arch/arm/mach-mx5/board-mx51_babbage.c +14 -2
@@ -34,6 +34,8 @@#include "devices-imx51.h" #include "devices.h" +#define BABBAGE_SDHCI1_WP (0*32 + 1)/* GPIO_1_1 */ +#define BABBAGE_SDHCI2_WP (0*32 + 5)/* GPIO_1_5 */ #define BABBAGE_USB_HUB_RESET (0*32 + 7)/* GPIO_1_7 */ #define BABBAGE_USBH1_STP (0*32 + 27)/* GPIO_1_27 */ #define BABBAGE_PHY_RESET (1*32 +5)/* GPIO_2_5 */
@@ -102,6 +104,7 @@ static struct pad_desc mx51babbage_pads[] = {MX51_PAD_SD1_DATA1__SD1_DATA1 ,MX51_PAD_SD1_DATA2__SD1_DATA2 ,MX51_PAD_SD1_DATA3__SD1_DATA3 , +MX51_PAD_GPIO_1_1__GPIO_1_1 ,/* SD 2 */ MX51_PAD_SD2_CMD__SD2_CMD,
@@ -110,6 +113,7 @@ static struct pad_desc mx51babbage_pads[] = {MX51_PAD_SD2_DATA1__SD2_DATA1 ,MX51_PAD_SD2_DATA2__SD2_DATA2 ,MX51_PAD_SD2_DATA3__SD2_DATA3 , + MX51_PAD_GPIO_1_5__GPIO_1_5, };/* Serial ports */
@@ -257,6 +261,14 @@ static int __init babbage_otg_mode(char *options) }__setup ("otg_mode=" , babbage_otg_mode); +static struct esdhc_platform_data esdhc_imx_pdata1 = { + .wp_gpio =BABBAGE_SDHCI1_WP , +}; + +static struct esdhc_platform_data esdhc_imx_pdata2 = { + .wp_gpio =BABBAGE_SDHCI2_WP , +}; +/* * Board specific initialization. */
@@ -286,8 +298,8 @@ static void __init mxc_board_init(void)mxc_iomux_v3_setup_pad (&usbh1stp);babbage_usbhub_reset (); -imx51_add_esdhc (0 ,NULL ); -imx51_add_esdhc (1 ,NULL ); +imx51_add_esdhc (0 , &esdhc_imx_pdata1); +imx51_add_esdhc (1 , &esdhc_imx_pdata2); }static void __init mx51_babbage_timer_init (void )
arch/arm/plat-mxc/include/mach/iomux-mx51.h +5 -3
@@ -43,7 +43,7 @@ typedef enum iomux_config {#define MX51_USBH1_PAD_CTRL (PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \ PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \ PAD_CTL_PKE | PAD_CTL_HYS) -#define MX51_GPIO_PAD_CTRL (PAD_CTL_DSE_HIGH | PAD_CTL_PKE | \ +#define MX51_GPIO_PAD_CTRL (PAD_CTL_DSE_HIGH | PAD_CTL_PKE | \ PAD_CTL_SRE_FAST)#define MX51_SDHCI_PAD_CTRL (PAD_CTL_DSE_HIGH | PAD_CTL_PUS_47K_UP | \ PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_SRE_FAST | \
@@ -310,7 +310,8 @@ typedef enum iomux_config {#define MX51_PAD_SD1_DATA3__SD1_DATA3 IOMUX_PAD(0x7B0, 0x3A8, IOMUX_CONFIG_SION, 0x0, 0, \ MX51_SDHCI_PAD_CTRL)#define MX51_PAD_GPIO_1_0__GPIO_1_0 IOMUX_PAD(0x7B4, 0x3AC, 1, 0x0, 0, NO_PAD_CTRL) -#define MX51_PAD_GPIO_1_1__GPIO_1_1 IOMUX_PAD(0x7B8, 0x3B0, 1, 0x0, 0, NO_PAD_CTRL) +#define MX51_PAD_GPIO_1_1__GPIO_1_1 IOMUX_PAD(0x7B8, 0x3B0, IOMUX_CONFIG_GPIO, 0x0, 0, \ + MX51_SDHCI_PAD_CTRL)#define MX51_PAD_SD2_CMD__SD2_CMD IOMUX_PAD(0x7BC, 0x3B4, IOMUX_CONFIG_SION, 0x0, 1, \ MX51_SDHCI_PAD_CTRL)#define MX51_PAD_SD2_CLK__SD2_CLK IOMUX_PAD(0x7C0, 0x3B8, IOMUX_CONFIG_SION, 0x0, 0, \
@@ -331,7 +332,8 @@ typedef enum iomux_config { 0x9bc, 3, MX51_I2C_PAD_CTRL)#define MX51_PAD_PMIC_INT_REQ__PMIC_INT_REQ IOMUX_PAD(0x7FC, 0x3D4, 0, 0x0, 0, NO_PAD_CTRL)#define MX51_PAD_GPIO_1_4__GPIO_1_4 IOMUX_PAD(0x804, 0x3D8, 0, 0x0, 0, NO_PAD_CTRL) -#define MX51_PAD_GPIO_1_5__GPIO_1_5 IOMUX_PAD(0x808, 0x3DC, 0, 0x0, 0, NO_PAD_CTRL) +#define MX51_PAD_GPIO_1_5__GPIO_1_5 IOMUX_PAD(0x808, 0x3DC, IOMUX_CONFIG_GPIO, 0x0, 1, \ + MX51_SDHCI_PAD_CTRL)#define MX51_PAD_GPIO_1_6__GPIO_1_6 IOMUX_PAD(0x80C, 0x3E0, 0, 0x0, 0, MX51_GPIO_PAD_CTRL)#define MX51_PAD_GPIO_1_7__GPIO_1_7 IOMUX_PAD(0x810, 0x3E4, 0, 0x0, 0, MX51_GPIO_PAD_CTRL)#define MX51_PAD_GPIO_1_8__GPIO_1_8 IOMUX_PAD(0x814, 0x3E8, 0, 0x0, 1, MX51_GPIO_PAD_CTRL)
Signature · 1 line
1.6.3.3
PATCH 2/2 Add the HW board caps flag for MX51 BBG
Some HW boards may have the bus-width caps limitation in HW design refer to the caps of the IC module.
For example, the MAX BUS width the eSDHC module on i.MX51 is up to 8bits.
But only the 1/4bits bus are supported on i.MX51 BBG boards.
--- arch/arm/mach-mx5/board-mx51_babbage.c | 3 +++ arch/arm/plat-mxc/include/mach/esdhc.h | 1 + drivers/mmc/host/sdhci-esdhc-imx.c | 1 + drivers/mmc/host/sdhci.c | 8 ++++++-- 4 files changed, 11 insertions(+), 2 deletions(-)
arch/arm/mach-mx5/board-mx51_babbage.c +3 -0
@@ -24,6 +24,7 @@#include <mach/iomux-mx51.h> #include <mach/i2c.h> #include <mach/mxc_ehci.h> +#include <mach/mmc.h> #include <asm/irq.h> #include <asm/setup.h>
@@ -263,10 +264,12 @@ __setup("otg_mode=", babbage_otg_mode);static struct esdhc_platform_data esdhc_imx_pdata1 = { .wp_gpio =BABBAGE_SDHCI1_WP , + .caps =MMC_CAP_4_BIT_DATA , };static struct esdhc_platform_data esdhc_imx_pdata2 = { .wp_gpio =BABBAGE_SDHCI2_WP , + .caps =MMC_CAP_4_BIT_DATA , };/*
arch/arm/plat-mxc/include/mach/esdhc.h +1 -0
@@ -12,5 +12,6 @@struct esdhc_platform_data {unsigned int wp_gpio;/* write protect pin */ +unsigned int caps;/* hw board esdhc caps */ };#endif /* __ASM_ARCH_IMX_ESDHC_H */
drivers/mmc/host/sdhci-esdhc-imx.c +1 -0
@@ -129,6 +129,7 @@ static int esdhc_pltfm_init(struct sdhci_host *host, struct sdhci_pltfm_data *pdif (boarddata) {gpio_request (boarddata->wp_gpio,"SD_WP" );gpio_direction_input (boarddata->wp_gpio); + host->caps |= boarddata->caps; }return 0 ; }
drivers/mmc/host/sdhci.c +6 -2
@@ -1848,8 +1848,12 @@ int sdhci_add_host(struct sdhci_host *host) mmc->f_max = host->max_clk; mmc->caps |=MMC_CAP_SDIO_IRQ ; -if (!(host->quirks &SDHCI_QUIRK_FORCE_1_BIT_DATA )) - mmc->caps |=MMC_CAP_4_BIT_DATA |MMC_CAP_8_BIT_DATA ; +if (!(host->quirks &SDHCI_QUIRK_FORCE_1_BIT_DATA )) { +if (host->caps &MMC_CAP_8_BIT_DATA ) + mmc->caps |=MMC_CAP_8_BIT_DATA ; +if (host->caps &MMC_CAP_4_BIT_DATA ) + mmc->caps |=MMC_CAP_4_BIT_DATA ; + }if (caps &SDHCI_CAN_DO_HISPD ) mmc->caps |=MMC_CAP_SD_HIGHSPEED |MMC_CAP_MMC_HIGHSPEED ;
Signature · 1 line
1.6.3.3
PATCH 1/2 Add the GPIO Write Protection Solution on i.MX51 BBG board
In reply to Richard ZhuHi Richard,
Quoted 10 lines · Richard Zhu
--- arch/arm/mach-mx5/board-mx51_babbage.c | 16 ++++++++++++++-- arch/arm/plat-mxc/include/mach/iomux-mx51.h | 8 +++++--- 2 files changed, 19 insertions(+), 5 deletions(-)arch/arm/mach-mx5/board-mx51_babbage.c +0
-0
arch/arm/mach-mx5/board-mx51_babbage.c line 38
Quoted 5 lines
arch/arm/mach-mx5/board-mx51_babbage.c +2
-0@@ -34,6 +34,8 @@#include "devices-imx51.h" #include "devices.h" +#define BABBAGE_SDHCI1_WP (0*32 + 1)/* GPIO_1_1 */ +#define BABBAGE_SDHCI2_WP (0*32 + 5)/* GPIO_1_5 */
Please mention in the subject of this patch that this "write protection" is related to the SDHCI device.
baruch
Signature · 3 lines
~. .~ Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
- baruch at tkos.co.il - tel: +972.2.679.5364, http://www.tkos.co.il -A message that is not in the archive (sent off-list or not yet received): 010C9052C42A00499CE76D637FA5EE90A516@039-SN1MPN1-002.039d.mgd.msft.net
Hi Richard,
Quoted 3 lines
Do you have any comments about the following patches? These patches add the GPIO write protection, and add the HW bus-width caps limitation.
First patch: The sdhci-part is okay (it's trivial enough), did not check the iomux-stuff, but I assume it works for you :) If you are basing your patch on my RFC-patches, it would be better for the process if you'd a) note the dependency in your patch and b) add some Acked-by or Tested-by to my original series.
Second patch: There is some discussion about the bus width currently going on. I'd suggest you join it.
BTW did you try adding regulator support yet?
Best regards,
Wolfram
Signature · 2 lines
Pengutronix e.K. | Wolfram Sang | Industrial Linux Solutions | http://www.pengutronix.de/ |