MPC52xx, motionpro: update default configuration
PATCH 1/1 MPC52xx, motionpro: update default configuration
Signed-off-by Wolfgang Denk <[email protected]>
--- include/configs/motionpro.h | 70 ++++++++++++++++-------------------------- 1 files changed, 27 insertions(+), 43 deletions(-)
include/configs/motionpro.h +27 -43
@@ -45,29 +45,27 @@#define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME -/* * Command line configuration. */ #include <config_cmd_default.h> #define CONFIG_CMD_ASKENV +#define CONFIG_CMD_BEDBUG +#define CONFIG_CMD_DATE #define CONFIG_CMD_DHCP -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_IMMAP +#define CONFIG_CMD_DTT +#define CONFIG_CMD_EEPROM #define CONFIG_CMD_ELF +#define CONFIG_CMD_FAT +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IDE +#define CONFIG_CMD_IMMAP +#define CONFIG_CMD_JFFS2 #define CONFIG_CMD_MII -#define CONFIG_CMD_BEDBUG #define CONFIG_CMD_NET #define CONFIG_CMD_PING -#define CONFIG_CMD_IDE -#define CONFIG_CMD_FAT -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_I2C -#define CONFIG_CMD_DATE -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_DTT - +#define CONFIG_CMD_REGINFO /* * Serial console configuration
@@ -77,7 +75,6 @@#define CONFIG_BAUDRATE 115200#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } -/* * Ethernet configuration */
@@ -99,11 +96,14 @@#define CONFIG_AUTOBOOT_PROMPT "Autobooting in %d seconds, " \ "press \"<Esc><Esc>\" to stop\n", bootdelay +#define CONFIG_CMDLINE_EDITING 1/* add command line history */ +#define CONFIG_SYS_HUSH_PARSER 1/* use "hush" command parser */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_ETHADDR 00:50:C2:40:10:00#define CONFIG_OVERWRITE_ETHADDR_ONCE 1#define CONFIG_VERSION_VARIABLE 1/* include version env variable */ -/* * Default environment settings */
@@ -115,21 +115,22 @@"serverip=192.168.1.1\0" \"gatewayip=192.168.1.1\0" \"console=ttyPSC0,115200\0" \ -"u-boot_addr=100000\0" \ -"kernel_addr=200000\0" \ -"fdt_addr=400000\0" \ -"ramdisk_addr=500000\0" \ +"u-boot_addr=400000\0" \ +"kernel_addr=400000\0" \ +"fdt_addr=700000\0" \ +"ramdisk_addr=800000\0" \"multi_image_addr=800000\0" \ -"rootpath=/opt/eldk-4.1/ppc_6xx\0" \ -"u-boot=/tftpboot/motionpro/u-boot.bin\0" \ -"bootfile=/tftpboot/motionpro/uImage\0" \ -"fdt_file=/tftpboot/motionpro/motionpro.dtb\0" \ -"ramdisk_file=/tftpboot/motionpro/uRamdisk\0" \ +"rootpath=/opt/eldk/ppc_6xx\0" \ +"u-boot=motionpro/u-boot.bin\0" \ +"bootfile=motionpro/uImage\0" \ +"fdt_file=motionpro/motionpro.dtb\0" \ +"ramdisk_file=motionpro/uRamdisk\0" \"multi_image_file=kernel+initrd+dtb.img\0" \"load=tftp ${u-boot_addr} ${u-boot}\0" \ -"update=prot off fff00000 fff3ffff; era fff00000 fff3ffff; " \ +"update=prot off fff00000 +${filesize};" \ +"era fff00000 +${filesize}; " \"cp.b ${u-boot_addr} fff00000 ${filesize};" \ -"prot on fff00000 fff3ffff\0" \ +"prot on fff00000 +${filesize}\0" \"ramargs=setenv bootargs root=/dev/ram rw\0" \"nfsargs=setenv bootargs root=/dev/nfs rw " \"nfsroot=${serverip}:${rootpath}\0" \
@@ -158,24 +159,20 @@*/ #define CONFIG_BOARD_EARLY_INIT_R 1 -/* * Low level configuration */ -/* * Clock configuration: SYS_XTALIN = 33MHz */ #define CONFIG_SYS_MPC5XXX_CLKIN 33000000 -/* * Set IPB speed to 100MHz */ #define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK -/* * Memory map */
@@ -184,7 +181,7 @@* Setting MBAR to otherwise will cause system hang when using SmartDMA such * as network commands. */ -#define CONFIG_SYS_MBAR 0xf0000000 +#define CONFIG_SYS_MBAR 0xf0000000#define CONFIG_SYS_SDRAM_BASE 0x00000000/*
@@ -216,7 +213,6 @@#define CONFIG_SYS_MALLOC_LEN (1024 << 10)/* 1 MiB for malloc() */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20)/* initial mem map for Linux */ -/* * Chip selects configuration */
@@ -249,7 +245,6 @@#define CONFIG_SYS_CS_BURST 0x00000000#define CONFIG_SYS_CS_DEADCYCLE 0x22222222 -/* * SDRAM configuration */
@@ -259,7 +254,6 @@#define SDRAM_CONTROL 0x504f0000#define SDRAM_MODE 0x00cd0000 -/* * Flash configuration */
@@ -297,7 +291,6 @@#define CONFIG_SYS_ATA_STRIDE 4#define CONFIG_DOS_PARTITION -/* * I2C configuration */
@@ -306,7 +299,6 @@#define CONFIG_SYS_I2C_SPEED 100000/* 100 kHz */ #define CONFIG_SYS_I2C_SLAVE 0x7F -/* * EEPROM configuration */
@@ -315,14 +307,12 @@#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5/* 2ms/cycle + 3ms extra */ #define CONFIG_SYS_I2C_MULTI_EEPROMS 1/* 2 EEPROMs (addr:50,52) */ -/* * RTC configuration */ #define CONFIG_RTC_DS1337 1#define CONFIG_SYS_I2C_RTC_ADDR 0x68 -/* * Status LED configuration */
@@ -344,14 +334,12 @@ extern void __led_toggle(led_id_t id);extern void __led_set (led_id_t id,int state);#endif /* __ASSEMBLY__ */ -/* * Temperature sensor */ #define CONFIG_DTT_LM75 1#define CONFIG_DTT_SENSORS { 0x49 } -/* * Environment settings */
@@ -379,13 +367,11 @@ extern void __led_set(led_id_t id, int state);*/ #define CONFIG_SYS_GPS_PORT_CONFIG 0x1105a004 -/* * Motion-PRO's CPLD revision control register */ #define CPLD_REV_REGISTER (CONFIG_SYS_CS2_START + 0x06) -/* * Miscellaneous configurable options */
@@ -404,7 +390,6 @@ extern void __led_set(led_id_t id, int state);#define CONFIG_SYS_HZ 1000/* decrementer freq: 1 ms ticks */ -/* * Various low-level settings */
@@ -416,7 +401,6 @@ extern void __led_set(led_id_t id, int state);#define CONFIG_SYS_CACHELINE_SIZE 32/* For MPC5xxx CPUs */ -/* Not needed for MPC 5xxx U-Boot, but used by tools/updater */ #define CONFIG_SYS_RESET_ADDRESS 0xfff00100
Signature · 1 line
1.7.2.3
Wolfgang Denk
AppliedPATCH 1/1 MPC52xx, motionpro: update default configuration
Quoted 4 lines · In message <[email protected]> I wrote:
Signed-off-by Wolfgang Denk <[email protected]>--- include/configs/motionpro.h | 70 ++++++++++++++++-------------------------- 1 files changed, 27 insertions(+), 43 deletions(-)
Applied.
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de A penny saved is a penny to squander. - Ambrose Bierce