hpsa updates, kdump fixes, PCI ID corrections and more

index c5d0606..030a880 100644
@@ -181,6 +181,10 @@ static int __devinit hpsa_find_cfg_addrs(struct pci_dev *pdev,
 static int __devinit hpsa_pci_find_memory_BAR(struct pci_dev *pdev,
 	unsigned long *memory_bar);
 static int __devinit hpsa_lookup_board_id(struct pci_dev *pdev, u32 *board_id);
+static int __devinit hpsa_wait_for_board_state(struct pci_dev *pdev,
+	void __iomem *vaddr, int wait_for_ready);
+#define BOARD_NOT_READY 0
+#define BOARD_READY 1
 
 static DEVICE_ATTR(raid_level, S_IRUGO, raid_level_show, NULL);
 static DEVICE_ATTR(lunid, S_IRUGO, lunid_show, NULL);

@@ -3260,6 +3264,20 @@ static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev)
 	   need a little pause here */
 	msleep(HPSA_POST_RESET_PAUSE_MSECS);
 
+	/* Wait for board to become not ready, then ready. */
+	dev_info(&pdev->dev, "Waiting for board to become ready.\n");
+	rc = hpsa_wait_for_board_state(pdev, vaddr, BOARD_NOT_READY);
+	if (rc)
+		dev_warn(&pdev->dev,
+			"failed waiting for board to become not ready\n");
+	rc = hpsa_wait_for_board_state(pdev, vaddr, BOARD_READY);
+	if (rc) {
+		dev_warn(&pdev->dev,
+			"failed waiting for board to become ready\n");
+		goto unmap_cfgtable;
+	}
+	dev_info(&pdev->dev, "board ready.\n");
+
 	/* Controller should be in simple mode at this point.  If it's not,
 	 * It means we're on one of those controllers which doesn't support
 	 * the doorbell reset method and on which the PCI power management reset

@@ -3455,18 +3473,28 @@ static int __devinit hpsa_pci_find_memory_BAR(struct pci_dev *pdev,
 	return -ENODEV;
 }
 
-static int __devinit hpsa_wait_for_board_ready(struct ctlr_info *h)
+static int __devinit hpsa_wait_for_board_state(struct pci_dev *pdev,
+	void __iomem *vaddr, int wait_for_ready)
 {
-	int i;
+	int i, iterations;
 	u32 scratchpad;
+	if (wait_for_ready)
+		iterations = HPSA_BOARD_READY_ITERATIONS;
+	else
+		iterations = HPSA_BOARD_NOT_READY_ITERATIONS;
 
-	for (i = 0; i < HPSA_BOARD_READY_ITERATIONS; i++) {
-		scratchpad = readl(h->vaddr + SA5_SCRATCHPAD_OFFSET);
-		if (scratchpad == HPSA_FIRMWARE_READY)
-			return 0;
+	for (i = 0; i < iterations; i++) {
+		scratchpad = readl(vaddr + SA5_SCRATCHPAD_OFFSET);
+		if (wait_for_ready) {
+			if (scratchpad == HPSA_FIRMWARE_READY)
+				return 0;
+		} else {
+			if (scratchpad != HPSA_FIRMWARE_READY)
+				return 0;
+		}
 		msleep(HPSA_BOARD_READY_POLL_INTERVAL_MSECS);
 	}
-	dev_warn(&h->pdev->dev, "board not ready, timed out.\n");
+	dev_warn(&pdev->dev, "board not ready, timed out.\n");
 	return -ENODEV;
 }
 

@@ -3658,7 +3686,7 @@ static int __devinit hpsa_pci_init(struct ctlr_info *h)
 		err = -ENOMEM;
 		goto err_out_free_res;
 	}
-	err = hpsa_wait_for_board_ready(h);
+	err = hpsa_wait_for_board_state(h->pdev, h->vaddr, BOARD_READY);
 	if (err)
 		goto err_out_free_res;
 	err = hpsa_find_cfgtables(h);

index a203ef6..9595c57 100644
@@ -155,12 +155,16 @@ struct ctlr_info {
  * HPSA_BOARD_READY_ITERATIONS are derived from those.
  */
 #define HPSA_BOARD_READY_WAIT_SECS (120)
+#define HPSA_BOARD_NOT_READY_WAIT_SECS (10)
 #define HPSA_BOARD_READY_POLL_INTERVAL_MSECS (100)
 #define HPSA_BOARD_READY_POLL_INTERVAL \
 	((HPSA_BOARD_READY_POLL_INTERVAL_MSECS * HZ) / 1000)
 #define HPSA_BOARD_READY_ITERATIONS \
 	((HPSA_BOARD_READY_WAIT_SECS * 1000) / \
 		HPSA_BOARD_READY_POLL_INTERVAL_MSECS)
+#define HPSA_BOARD_NOT_READY_ITERATIONS \
+	((HPSA_BOARD_NOT_READY_WAIT_SECS * 1000) / \
+		HPSA_BOARD_READY_POLL_INTERVAL_MSECS)
 #define HPSA_POST_RESET_PAUSE_MSECS (3000)
 #define HPSA_POST_RESET_NOOP_RETRIES (12)
 

index 030a880..542cb2b 100644
@@ -3076,38 +3076,6 @@ static __devinit int hpsa_message(struct pci_dev *pdev, unsigned char opcode,
 #define hpsa_soft_reset_controller(p) hpsa_message(p, 1, 0)
 #define hpsa_noop(p) hpsa_message(p, 3, 0)
 
-static __devinit int hpsa_reset_msi(struct pci_dev *pdev)
-{
-/* the #defines are stolen from drivers/pci/msi.h. */
-#define msi_control_reg(base)		(base + PCI_MSI_FLAGS)
-#define PCI_MSIX_FLAGS_ENABLE		(1 << 15)
-
-	int pos;
-	u16 control = 0;
-
-	pos = pci_find_capability(pdev, PCI_CAP_ID_MSI);
-	if (pos) {
-		pci_read_config_word(pdev, msi_control_reg(pos), &control);
-		if (control & PCI_MSI_FLAGS_ENABLE) {
-			dev_info(&pdev->dev, "resetting MSI\n");
-			pci_write_config_word(pdev, msi_control_reg(pos),
-					control & ~PCI_MSI_FLAGS_ENABLE);
-		}
-	}
-
-	pos = pci_find_capability(pdev, PCI_CAP_ID_MSIX);
-	if (pos) {
-		pci_read_config_word(pdev, msi_control_reg(pos), &control);
-		if (control & PCI_MSIX_FLAGS_ENABLE) {
-			dev_info(&pdev->dev, "resetting MSI-X\n");
-			pci_write_config_word(pdev, msi_control_reg(pos),
-					control & ~PCI_MSIX_FLAGS_ENABLE);
-		}
-	}
-
-	return 0;
-}
-
 static int hpsa_controller_hard_reset(struct pci_dev *pdev,
 	void * __iomem vaddr, bool use_doorbell)
 {

@@ -3163,17 +3131,17 @@ static int hpsa_controller_hard_reset(struct pci_dev *pdev,
  */
 static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev)
 {
-	u16 saved_config_space[32];
 	u64 cfg_offset;
 	u32 cfg_base_addr;
 	u64 cfg_base_addr_index;
 	void __iomem *vaddr;
 	unsigned long paddr;
 	u32 misc_fw_support, active_transport;
-	int rc, i;
+	int rc;
 	struct CfgTable __iomem *cfgtable;
 	bool use_doorbell;
 	u32 board_id;
+	u16 command_register;
 
 	/* For controllers as old as the P600, this is very nearly
 	 * the same thing as

@@ -3183,14 +3151,6 @@ static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev)
 	 * pci_set_power_state(pci_dev, PCI_D0);
 	 * pci_restore_state(pci_dev);
 	 *
-	 * but we can't use these nice canned kernel routines on
-	 * kexec, because they also check the MSI/MSI-X state in PCI
-	 * configuration space and do the wrong thing when it is
-	 * set/cleared.  Also, the pci_save/restore_state functions
-	 * violate the ordering requirements for restoring the
-	 * configuration space from the CCISS document (see the
-	 * comment below).  So we roll our own ....
-	 *
 	 * For controllers newer than the P600, the pci power state
 	 * method of resetting doesn't work so we have another way
 	 * using the doorbell register.

@@ -3207,9 +3167,13 @@ static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev)
 	if (board_id == 0x409C0E11 || board_id == 0x409D0E11)
 		return -ENOTSUPP;
 
-	for (i = 0; i < 32; i++)
-		pci_read_config_word(pdev, 2*i, &saved_config_space[i]);
-
+	/* Save the PCI command register */
+	pci_read_config_word(pdev, 4, &command_register);
+	/* Turn the board off.  This is so that later pci_restore_state()
+	 * won't turn the board on before the rest of config space is ready.
+	 */
+	pci_disable_device(pdev);
+	pci_save_state(pdev);
 
 	/* find the first memory BAR, so we can find the cfg table */
 	rc = hpsa_pci_find_memory_BAR(pdev, &paddr);

@@ -3235,30 +3199,17 @@ static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev)
 	misc_fw_support = readl(&cfgtable->misc_fw_support);
 	use_doorbell = misc_fw_support & MISC_FW_DOORBELL_RESET;
 
-	/* The doorbell reset seems to cause lockups on some Smart
-	 * Arrays (e.g. P410, P410i, maybe others).  Until this is
-	 * fixed or at least isolated, avoid the doorbell reset.
-	 */
-	use_doorbell = 0;
-
 	rc = hpsa_controller_hard_reset(pdev, vaddr, use_doorbell);
 	if (rc)
 		goto unmap_cfgtable;
 
-	/* Restore the PCI configuration space.  The Open CISS
-	 * Specification says, "Restore the PCI Configuration
-	 * Registers, offsets 00h through 60h. It is important to
-	 * restore the command register, 16-bits at offset 04h,
-	 * last. Do not restore the configuration status register,
-	 * 16-bits at offset 06h."  Note that the offset is 2*i.
-	 */
-	for (i = 0; i < 32; i++) {
-		if (i == 2 || i == 3)
-			continue;
-		pci_write_config_word(pdev, 2*i, saved_config_space[i]);
+	pci_restore_state(pdev);
+	rc = pci_enable_device(pdev);
+	if (rc) {
+		dev_warn(&pdev->dev, "failed to enable device.\n");
+		goto unmap_cfgtable;
 	}
-	wmb();
-	pci_write_config_word(pdev, 4, saved_config_space[2]);
+	pci_write_config_word(pdev, 4, command_register);
 
 	/* Some devices (notably the HP Smart Array 5i Controller)
 	   need a little pause here */

@@ -3755,8 +3706,6 @@ static __devinit int hpsa_init_reset_devices(struct pci_dev *pdev)
 		return 0; /* just try to do the kdump anyhow. */
 	if (rc)
 		return -ENODEV;
-	if (hpsa_reset_msi(pdev))
-		return -ENODEV;
 
 	/* Now try to get the controller to respond to a no-op */
 	for (i = 0; i < HPSA_POST_RESET_NOOP_RETRIES; i++) {

index 542cb2b..ba2becc 100644
@@ -3493,6 +3493,11 @@ static int __devinit hpsa_find_cfgtables(struct ctlr_info *h)
 static void __devinit hpsa_get_max_perf_mode_cmds(struct ctlr_info *h)
 {
 	h->max_commands = readl(&(h->cfgtable->MaxPerformantModeCommands));
+
+	/* Limit commands in memory limited kdump scenario. */
+	if (reset_devices && h->max_commands > 32)
+		h->max_commands = 32;
+
 	if (h->max_commands < 16) {
 		dev_warn(&h->pdev->dev, "Controller reports "
 			"max supported commands of %d, an obvious lie. "

index ba2becc..d618432 100644
@@ -3163,7 +3163,11 @@ static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev)
 	 * likely not be happy.  Just forbid resetting this conjoined mess.
 	 * The 640x isn't really supported by hpsa anyway.
 	 */
-	hpsa_lookup_board_id(pdev, &board_id);
+	rc = hpsa_lookup_board_id(pdev, &board_id);
+	if (rc < 0) {
+		dev_warn(&pdev->dev, "Not resetting device.\n");
+		return -ENODEV;
+	}
 	if (board_id == 0x409C0E11 || board_id == 0x409D0E11)
 		return -ENOTSUPP;
 

index d618432..ffc5f74 100644
@@ -3576,13 +3576,18 @@ static inline void hpsa_p600_dma_prefetch_quirk(struct ctlr_info *h)
 static void __devinit hpsa_wait_for_mode_change_ack(struct ctlr_info *h)
 {
 	int i;
+	u32 doorbell_value;
+	unsigned long flags;
 
 	/* under certain very rare conditions, this can take awhile.
 	 * (e.g.: hot replace a failed 144GB drive in a RAID 5 set right
 	 * as we enter this code.)
 	 */
 	for (i = 0; i < MAX_CONFIG_WAIT; i++) {
-		if (!(readl(h->vaddr + SA5_DOORBELL) & CFGTBL_ChangeReq))
+		spin_lock_irqsave(&h->lock, flags);
+		doorbell_value = readl(h->vaddr + SA5_DOORBELL);
+		spin_unlock_irqrestore(&h->lock, flags);
+		if (!doorbell_value & CFGTBL_ChangeReq)
 			break;
 		/* delay and try again */
 		msleep(10);

@@ -3754,6 +3759,8 @@ static int __devinit hpsa_init_one(struct pci_dev *pdev,
 	h->busy_initializing = 1;
 	INIT_HLIST_HEAD(&h->cmpQ);
 	INIT_HLIST_HEAD(&h->reqQ);
+	spin_lock_init(&h->lock);
+	spin_lock_init(&h->scan_lock);
 	rc = hpsa_pci_init(h);
 	if (rc != 0)
 		goto clean1;

@@ -3813,8 +3820,6 @@ static int __devinit hpsa_init_one(struct pci_dev *pdev,
 	}
 	if (hpsa_allocate_sg_chain_blocks(h))
 		goto clean4;
-	spin_lock_init(&h->lock);
-	spin_lock_init(&h->scan_lock);
 	init_waitqueue_head(&h->scan_wait_queue);
 	h->scan_finished = 1; /* no scan currently in progress */
 

index ffc5f74..a68dba7 100644
@@ -75,6 +75,10 @@ static int hpsa_allow_any;
 module_param(hpsa_allow_any, int, S_IRUGO|S_IWUSR);
 MODULE_PARM_DESC(hpsa_allow_any,
 		"Allow hpsa driver to access unknown HP Smart Array hardware");
+static int hpsa_simple_mode;
+module_param(hpsa_simple_mode, int, S_IRUGO|S_IWUSR);
+MODULE_PARM_DESC(hpsa_simple_mode,
+	"Use 'simple mode' rather than 'performant mode'");
 
 /* define the PCI info for the cards we can control */
 static const struct pci_device_id hpsa_pci_device_id[] = {

@@ -4061,6 +4065,9 @@ static __devinit void hpsa_put_ctlr_into_performant_mode(struct ctlr_info *h)
 {
 	u32 trans_support;
 
+	if (hpsa_simple_mode)
+		return;
+
 	trans_support = readl(&(h->cfgtable->TransportSupport));
 	if (!(trans_support & PERFORMANT_MODE))
 		return;

index a68dba7..c36427d 100644
@@ -3594,7 +3594,7 @@ static void __devinit hpsa_wait_for_mode_change_ack(struct ctlr_info *h)
 		if (!doorbell_value & CFGTBL_ChangeReq)
 			break;
 		/* delay and try again */
-		msleep(10);
+		usleep_range(10000, 20000);
 	}
 }
 

index c36427d..cba5bf4 100644
@@ -2458,15 +2458,17 @@ static int hpsa_passthru_ioctl(struct ctlr_info *h, void __user *argp)
 		buff = kmalloc(iocommand.buf_size, GFP_KERNEL);
 		if (buff == NULL)
 			return -EFAULT;
-	}
-	if (iocommand.Request.Type.Direction == XFER_WRITE) {
-		/* Copy the data into the buffer we created */
-		if (copy_from_user(buff, iocommand.buf, iocommand.buf_size)) {
-			kfree(buff);
-			return -EFAULT;
+		if (iocommand.Request.Type.Direction == XFER_WRITE) {
+			/* Copy the data into the buffer we created */
+			if (copy_from_user(buff, iocommand.buf,
+				iocommand.buf_size)) {
+				kfree(buff);
+				return -EFAULT;
+			}
+		} else {
+			memset(buff, 0, iocommand.buf_size);
 		}
-	} else
-		memset(buff, 0, iocommand.buf_size);
+	}
 	c = cmd_special_alloc(h);
 	if (c == NULL) {
 		kfree(buff);

@@ -2512,8 +2514,8 @@ static int hpsa_passthru_ioctl(struct ctlr_info *h, void __user *argp)
 		cmd_special_free(h, c);
 		return -EFAULT;
 	}
-
-	if (iocommand.Request.Type.Direction == XFER_READ) {
+	if (iocommand.Request.Type.Direction == XFER_READ &&
+		iocommand.buf_size > 0) {
 		/* Copy the data out of the buffer we created */
 		if (copy_to_user(iocommand.buf, buff, iocommand.buf_size)) {
 			kfree(buff);

@@ -2606,14 +2608,7 @@ static int hpsa_big_passthru_ioctl(struct ctlr_info *h, void __user *argp)
 	}
 	c->cmd_type = CMD_IOCTL_PEND;
 	c->Header.ReplyQueue = 0;
-
-	if (ioc->buf_size > 0) {
-		c->Header.SGList = sg_used;
-		c->Header.SGTotal = sg_used;
-	} else {
-		c->Header.SGList = 0;
-		c->Header.SGTotal = 0;
-	}
+	c->Header.SGList = c->Header.SGTotal = sg_used;
 	memcpy(&c->Header.LUN, &ioc->LUN_info, sizeof(c->Header.LUN));
 	c->Header.Tag.lower = c->busaddr;
 	memcpy(&c->Request, &ioc->Request, sizeof(c->Request));

@@ -2630,7 +2625,8 @@ static int hpsa_big_passthru_ioctl(struct ctlr_info *h, void __user *argp)
 		}
 	}
 	hpsa_scsi_do_simple_cmd_core(h, c);
-	hpsa_pci_unmap(h->pdev, c, sg_used, PCI_DMA_BIDIRECTIONAL);
+	if (sg_used)
+		hpsa_pci_unmap(h->pdev, c, sg_used, PCI_DMA_BIDIRECTIONAL);
 	check_ioctl_unit_attention(h, c);
 	/* Copy the error information out */
 	memcpy(&ioc->error_info, c->err_info, sizeof(ioc->error_info));

@@ -2639,7 +2635,7 @@ static int hpsa_big_passthru_ioctl(struct ctlr_info *h, void __user *argp)
 		status = -EFAULT;
 		goto cleanup1;
 	}
-	if (ioc->Request.Type.Direction == XFER_READ) {
+	if (ioc->Request.Type.Direction == XFER_READ && ioc->buf_size > 0) {
 		/* Copy the data out of the buffer we created */
 		BYTE __user *ptr = ioc->buf;
 		for (i = 0; i < sg_used; i++) {

index cba5bf4..862b0ae 100644
@@ -167,6 +167,8 @@ static ssize_t unique_id_show(struct device *dev,
 	struct device_attribute *attr, char *buf);
 static ssize_t host_show_firmware_revision(struct device *dev,
 	     struct device_attribute *attr, char *buf);
+static ssize_t host_show_commands_outstanding(struct device *dev,
+	     struct device_attribute *attr, char *buf);
 static void hpsa_update_scsi_devices(struct ctlr_info *h, int hostno);
 static ssize_t host_store_rescan(struct device *dev,
 	 struct device_attribute *attr, const char *buf, size_t count);

@@ -196,6 +198,8 @@ static DEVICE_ATTR(unique_id, S_IRUGO, unique_id_show, NULL);
 static DEVICE_ATTR(rescan, S_IWUSR, NULL, host_store_rescan);
 static DEVICE_ATTR(firmware_revision, S_IRUGO,
 	host_show_firmware_revision, NULL);
+static DEVICE_ATTR(commands_outstanding, S_IRUGO,
+	host_show_commands_outstanding, NULL);
 
 static struct device_attribute *hpsa_sdev_attrs[] = {
 	&dev_attr_raid_level,

@@ -207,6 +211,7 @@ static struct device_attribute *hpsa_sdev_attrs[] = {
 static struct device_attribute *hpsa_shost_attrs[] = {
 	&dev_attr_rescan,
 	&dev_attr_firmware_revision,
+	&dev_attr_commands_outstanding,
 	NULL,
 };
 

@@ -307,6 +312,15 @@ static ssize_t host_show_firmware_revision(struct device *dev,
 		fwrev[0], fwrev[1], fwrev[2], fwrev[3]);
 }
 
+static ssize_t host_show_commands_outstanding(struct device *dev,
+	     struct device_attribute *attr, char *buf)
+{
+	struct Scsi_Host *shost = class_to_shost(dev);
+	struct ctlr_info *h = shost_to_hba(shost);
+
+	return snprintf(buf, 20, "%d\n", h->commands_outstanding);
+}
+
 /* Enqueuing and dequeuing functions for cmdlists. */
 static inline void addQ(struct hlist_head *list, struct CommandList *c)
 {

index 862b0ae..d5bca36 100644
@@ -120,11 +120,11 @@ static struct board_type products[] = {
 	{0x324b103C, "Smart Array P711m", &SA5_access},
 	{0x3233103C, "StorageWorks P1210m", &SA5_access},
 	{0x333F103C, "StorageWorks P1210m", &SA5_access},
-	{0x3250103C, "Smart Array", &SA5_access},
-	{0x3250113C, "Smart Array", &SA5_access},
-	{0x3250123C, "Smart Array", &SA5_access},
-	{0x3250133C, "Smart Array", &SA5_access},
-	{0x3250143C, "Smart Array", &SA5_access},
+	{0x3350103C, "Smart Array", &SA5_access},
+	{0x3351103C, "Smart Array", &SA5_access},
+	{0x3352103C, "Smart Array", &SA5_access},
+	{0x3353103C, "Smart Array", &SA5_access},
+	{0x3354103C, "Smart Array", &SA5_access},
 	{0xFFFF103C, "Unknown Smart Array", &SA5_access},
 };