Skip to contentSkip to conversation

mx51evk: support new relocation scheme

PATCH Superseded Shawn Guo 5 participants 15 messages Oct 27, 2010 – Oct 28, 2010

Subsystems (2)
lore
Share & tools
lore

Shawn Guo

author
#0 lore raw

PATCH v2 1/1 mx51evk: support new relocation scheme

This patch is to fix build breakage and support new relocatoin scheme for mx51evk.

- Correct IRAM base address and add size definition

The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than 0x1FFE8000 which is for older revision.

- Include imx-regs.h in mx51evk.h

Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be referred to.

- Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE

This is something suggested by Wolfgang, and for automatic calculation of macros like CONFIG_SYS_GBL_DATA_SIZE (done) and CONFIG_SYS_INIT_SP_ADDR (later).

- Remove comment for CONFIG_SYS_GBL_DATA_SIZE which has been buried by Wolfgang's commit below

25ddd1fb: Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

---
Changes for v2:
- Combine two patches before into one, as the separation is not so logical.
- Define init stack at the end of init RAM to address comments from Stefano, Heiko and Wolfgang.

 arch/arm/include/asm/arch-mx5/imx-regs.h |    3 ++-
 board/freescale/mx51evk/mx51evk.c        |    6 +++---
 include/configs/mx51evk.h                |    9 +++++++--
 3 files changed, 12 insertions(+), 6 deletions(-)
arch/arm/include/asm/arch-mx5/imx-regs.h +2 -1
index 3ddda40..0b6249a 100644
@@ -26,7 +26,8 @@
 /*
  * IRAM
  */
-#define IRAM_BASE_ADDR		0x1FFE8000	/* internal ram */
+#define IRAM_BASE_ADDR		0x1FFE0000	/* internal ram */
+#define IRAM_SIZE		0x00020000	/* 128 KB */
 /*
  * Graphics Memory of GPU
  */
board/freescale/mx51evk/mx51evk.c +3 -3
index c8d7d39..8820698 100644
@@ -52,9 +52,9 @@ u32 get_board_rev(void)
 
 int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1,
-			PHYS_SDRAM_1_SIZE);
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_1_SIZE);
 	return 0;
 }
 
include/configs/mx51evk.h +7 -2
index f31fc4e..6dc1ffc 100644
@@ -24,11 +24,11 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#include <asm/arch/imx-regs.h>
 
  /* High Level Configuration Options */
 
 #define CONFIG_MX51	/* in a mx51 */
-#define CONFIG_SKIP_RELOCATE_UBOOT
 
 #define CONFIG_SYS_MX5_HCLK	24000000
 #define CONFIG_SYS_MX5_CLK32		32768
@@ -51,7 +51,6 @@
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2 * 1024 * 1024)
-/* size in bytes reserved for initial data */
 
 #define BOARD_LATE_INIT
 
@@ -174,6 +173,12 @@
 #define PHYS_SDRAM_1		CSD0_BASE_ADDR
 #define PHYS_SDRAM_1_SIZE	(512 * 1024 * 1024)
 
+#define CONFIG_SYS_SDRAM_BASE		(PHYS_SDRAM_1)
+#define CONFIG_SYS_INIT_RAM_ADDR	(IRAM_BASE_ADDR)
+#define CONFIG_SYS_INIT_RAM_SIZE	(IRAM_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR	\
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE)
+
 #define CONFIG_SYS_DDR_CLKSEL	0
 #define CONFIG_SYS_CLKTL_CBCDR	0x59E35100
 
Signature · 1 line
1.7.1
#1 lore raw

PATCH v2 1/1 mx51evk: support new relocation scheme

Quoted 19 lines · Shawn Guo

This patch is to fix build breakage and support new relocatoin scheme for mx51evk.

- Correct IRAM base address and add size definition

The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than 0x1FFE8000 which is for older revision.

- Include imx-regs.h in mx51evk.h

Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be referred to.

- Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE

This is something suggested by Wolfgang, and for automatic calculation of macros like CONFIG_SYS_GBL_DATA_SIZE (done) and CONFIG_SYS_INIT_SP_ADDR (later).

Quoted 6 lines

- Remove comment for CONFIG_SYS_GBL_DATA_SIZE which has been buried by Wolfgang's commit below

25ddd1fb: Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================
#2 lore raw

PATCH v2 1/1 mx51evk: support new relocation scheme

In reply to Shawn Guo

2010/10/27 Shawn Guo <[email protected]>:

Quoted 2 lines

This patch is to fix build breakage and support new relocatoin scheme for mx51evk.

What's change is for the build breakage fix? Please state it clearly.

Quoted 112 lines

- Correct IRAM base address and add size definition

?The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than ?0x1FFE8000 which is for older revision.

- Include imx-regs.h in mx51evk.h

?Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be ?referred to.

- Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE

?This is something suggested by Wolfgang, and for automatic ?calculation of macros like CONFIG_SYS_GBL_DATA_SIZE (done) and ?CONFIG_SYS_INIT_SP_ADDR (later).

- Remove comment for CONFIG_SYS_GBL_DATA_SIZE which has been ?buried by Wolfgang's commit below

?25ddd1fb: Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

---
Changes for v2:
?- Combine two patches before into one, as the separation is not ? so logical.
?- Define init stack at the end of init RAM to address comments ? from Stefano, Heiko and Wolfgang.

?arch/arm/include/asm/arch-mx5/imx-regs.h | ? ?3 ++-
?board/freescale/mx51evk/mx51evk.c ? ? ? ?| ? ?6 +++---
?include/configs/mx51evk.h ? ? ? ? ? ? ? ?| ? ?9 +++++++--

?3 files changed, 12 insertions(+), 6 deletions(-)

arch/arm/include/asm/arch-mx5/imx-regs.h +0 -0
index 3ddda40..0b6249a 100644
@@ -26,7 +26,8 @@

?/*
?* IRAM
?*/

arch/arm/include/asm/arch-mx5/imx-regs.h +2 -1
-#define IRAM_BASE_ADDR ? ? ? ? 0x1FFE8000 ? ? ?/* internal ram */
+#define IRAM_BASE_ADDR ? ? ? ? 0x1FFE0000 ? ? ?/* internal ram */
+#define IRAM_SIZE ? ? ? ? ? ? ?0x00020000 ? ? ?/* 128 KB */

?/*
?* Graphics Memory of GPU
?*/

board/freescale/mx51evk/mx51evk.c +3 -3
index c8d7d39..8820698 100644
@@ -52,9 +52,9 @@ u32 get_board_rev(void)
 
 ?int dram_init(void)
 ?{
- ? ? ? gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- ? ? ? gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1,
- ? ? ? ? ? ? ? ? ? ? ? PHYS_SDRAM_1_SIZE);
+ ? ? ? /* dram_init must store complete ramsize in gd->ram_size */
+ ? ? ? gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? PHYS_SDRAM_1_SIZE);
 ? ? ? ?return 0;
 ?}
 
include/configs/mx51evk.h +0 -0
index f31fc4e..6dc1ffc 100644
@@ -24,11 +24,11 @@

?#ifndef __CONFIG_H
?#define __CONFIG_H

+#include <asm/arch/imx-regs.h>

?/* High Level Configuration Options */

?#define CONFIG_MX51 ? ?/* in a mx51 */
-#define CONFIG_SKIP_RELOCATE_UBOOT

?#define CONFIG_SYS_MX5_HCLK ? ?24000000
?#define CONFIG_SYS_MX5_CLK32 ? ? ? ? ? 32768

include/configs/mx51evk.h +0 -0
@@ -51,7 +51,6 @@

?* Size of malloc() pool
?*/
?#define CONFIG_SYS_MALLOC_LEN ? ? ? ? ?(CONFIG_ENV_SIZE + 2 * 1024 * 1024) -/* size in bytes reserved for initial data */

?#define BOARD_LATE_INIT

include/configs/mx51evk.h +0 -0
@@ -174,6 +173,12 @@

?#define PHYS_SDRAM_1 ? ? ? ? ? CSD0_BASE_ADDR ?#define PHYS_SDRAM_1_SIZE ? ? ?(512 * 1024 * 1024)

include/configs/mx51evk.h +6 -0
+#define CONFIG_SYS_SDRAM_BASE ? ? ? ? ?(PHYS_SDRAM_1)
+#define CONFIG_SYS_INIT_RAM_ADDR ? ? ? (IRAM_BASE_ADDR)
+#define CONFIG_SYS_INIT_RAM_SIZE ? ? ? (IRAM_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR ? ? ? ?\
+ ? ? ? (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE)
+

?#define CONFIG_SYS_DDR_CLKSEL ?0
?#define CONFIG_SYS_CLKTL_CBCDR 0x59E35100

--
1.7.1

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

author
#3 lore raw

PATCH v2 1/1 mx51evk: support new relocation scheme

Quoted 6 lines · Jason Liu

2010/10/27 Shawn Guo <[email protected]>:

Quoted 2 lines

This patch is to fix build breakage and support new relocatoin scheme for mx51evk.

What's change is for the build breakage fix? Please state it clearly.

The new relocation scheme requires the definition of CONFIG_SYS_INIT_SP_ADDR and CONFIG_SYS_SDRAM_BASE. It's the reason that build on master has been in failure for some time.

Signature · 2 lines
Regards,
Shawn
#4 lore raw

PATCH v2 1/1 mx51evk: support new relocation scheme

2010/10/27 Shawn Guo <[email protected]>:

Quoted 10 lines · Jason Liu
Quoted 6 lines

2010/10/27 Shawn Guo <[email protected]>:

Quoted 2 lines

This patch is to fix build breakage and support new relocatoin scheme for mx51evk.

What's change is for the build breakage fix? Please state it clearly.

The new relocation scheme requires the definition of CONFIG_SYS_INIT_SP_ADDR and CONFIG_SYS_SDRAM_BASE. It's the reason that build on master has been in failure for some time.

Okay, I noticed that Stefano has already sent out patch before to fix relocation and I have applied his patch on my local tree, so I don't find build break.

Quoted 5 lines

--
Regards,
Shawn

#5 lore raw

PATCH v2 1/1 mx51evk: support new relocation scheme

In reply to Shawn Guo

Dear Shawn Guo,

Quoted 10 lines · In message <[email protected]> you wrote:

This patch is to fix build breakage and support new relocatoin scheme for mx51evk.

- Correct IRAM base address and add size definition

The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than 0x1FFE8000 which is for older revision.

- Include imx-regs.h in mx51evk.h

Quoted 8 lines

Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be referred to.

- Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE

This is something suggested by Wolfgang, and for automatic calculation of macros like CONFIG_SYS_GBL_DATA_SIZE (done) and CONFIG_SYS_INIT_SP_ADDR (later).

Um... this is NOT what we discussed.

include/configs/mx51evk.h line 181

Quoted 6 lines
include/configs/mx51evk.h +6 -0
+#define CONFIG_SYS_SDRAM_BASE		(PHYS_SDRAM_1)
+#define CONFIG_SYS_INIT_RAM_ADDR	(IRAM_BASE_ADDR)
+#define CONFIG_SYS_INIT_RAM_SIZE	(IRAM_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR	\
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE)
+

No. This is not what I want to se.

Memory allocation in the inital ram has the global data at the top.

Please use something like

#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"Whoever undertakes to set himself up as a judge of Truth  and  Know-
ledge is shipwrecked by the laughter of the gods."  - Albert Einstein
author
#6 lore raw

PATCH v2 1/1 mx51evk: support new relocation scheme

Quoted 16 lines · Wolfgang Denk

Dear Shawn Guo,

Quoted 13 lines · In message <[email protected]> you wrote:

This patch is to fix build breakage and support new relocatoin scheme for mx51evk.

- Correct IRAM base address and add size definition

? The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than ? 0x1FFE8000 which is for older revision.

- Include imx-regs.h in mx51evk.h

? Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be ? referred to.

Quoted 8 lines
Quoted 5 lines

- Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE

? This is something suggested by Wolfgang, and for automatic ? calculation of macros like CONFIG_SYS_GBL_DATA_SIZE (done) and ? CONFIG_SYS_INIT_SP_ADDR (later).

Um... this is NOT what we discussed.

Are you saying that automatic calculation of CONFIG_SYS_INIT_SP_ADDR will not happen?

Quoted 10 lines

No. ?This is not what I want to se.

Memory allocation in the inital ram has the global data at the top.

Please use something like

#define CONFIG_SYS_INIT_SP_OFFSET ?(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_ADDR ? ?(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

If the automatic calculation of CONFIG_SYS_INIT_SP_ADDR will not happen, I can send another patch to fix it, since it's been applied by Stefano already.

Signature · 2 lines
Regards,
Shawn
#7 lore raw

PATCH v2 1/1 mx51evk: support new relocation scheme

Quoted 33 lines · Shawn Guo
Quoted 16 lines · Wolfgang Denk

Dear Shawn Guo,

Quoted 13 lines · In message <[email protected]> you wrote:

This patch is to fix build breakage and support new relocatoin scheme for mx51evk.

- Correct IRAM base address and add size definition

The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than 0x1FFE8000 which is for older revision.

- Include imx-regs.h in mx51evk.h

Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be referred to.

Quoted 8 lines
Quoted 5 lines

- Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE

This is something suggested by Wolfgang, and for automatic calculation of macros like CONFIG_SYS_GBL_DATA_SIZE (done) and CONFIG_SYS_INIT_SP_ADDR (later).

Um... this is NOT what we discussed.

Are you saying that automatic calculation of CONFIG_SYS_INIT_SP_ADDR will not happen?

Quoted 5 lines

No. This is not what I want to se.

Memory allocation in the inital ram has the global data at the top.

Quoted 8 lines
Quoted 5 lines

Please use something like

#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

If the automatic calculation of CONFIG_SYS_INIT_SP_ADDR will not happen, I can send another patch to fix it, since it's been applied by Stefano already.

Sorry for that. I was too fast and I have not read the patch with attention. I revert the patch after I see Wolfgang's comment. You can send V3 version of this patch and you can forget the "applied" message.

Stefano

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================
#8 lore raw

PATCH v2 1/1 mx51evk: support new relocation scheme

In reply to Shawn Guo

Dear Shawn Guo,

Quoted 9 lines · In message <[email protected]> you…
Quoted 6 lines

Please use something like

#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

If the automatic calculation of CONFIG_SYS_INIT_SP_ADDR will not happen, I can send another patch to fix it, since it's been applied by Stefano already.

Yes, it will.

But the stack pointer will not start at the end of the initial ram area, but below the global data area which lies at the end.

Best regards,

Wolfgang Denk

Signature · 4 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Always leave room to add an explanation if it doesn't work out.
author
#9 lore raw

PATCH v2 1/1 mx51evk: support new relocation scheme

Quoted 9 lines · Wolfgang Denk

Dear Shawn Guo,

Quoted 6 lines · In message <[email protected]> you…
Quoted 6 lines

Please use something like

#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_ADDR ?(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

Quoted 9 lines
Quoted 3 lines

If the automatic calculation of CONFIG_SYS_INIT_SP_ADDR will not happen, I can send another patch to fix it, since it's been applied by Stefano already.

Yes, it will.

But the stack pointer will not start at the end of the initial ram area, but below the global data area which lies at the end.

I thought the manual definition of CONFIG_SYS_INIT_SP_ADDR is the near term solution, since it will be replaced by automatic calculation. So I did not put much attention to reflect the layout you want to see.

Anyway, v3 is coming soon.

Signature · 2 lines
Regards,
Shawn
#10 lore raw

PATCH v2 1/1 mx51evk: support new relocation scheme

Dear Shawn Guo,

Quoted 7 lines · In message <[email protected]> you…
Quoted 4 lines

But the stack pointer will not start at the end of the initial ram area, but below the global data area which lies at the end.

I thought the manual definition of CONFIG_SYS_INIT_SP_ADDR is the near term solution, since it will be replaced by automatic calculation. So I did not put much attention to reflect the layout you want to see.

Well, we can only calculate this automatically if all boards us the same layout of the internal RAM area. That's why this is needed.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
The more we disagree, the more chance there is that at least  one  of
us is right.
author
#11 lore raw

PATCH v2 1/1 mx51evk: support new relocation scheme

In reply to Wolfgang Denk
Quoted 33 lines · Wolfgang Denk

Dear Shawn Guo,

Quoted 10 lines · In message <[email protected]> you wrote:

This patch is to fix build breakage and support new relocatoin scheme for mx51evk.

- Correct IRAM base address and add size definition

? The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than ? 0x1FFE8000 which is for older revision.

- Include imx-regs.h in mx51evk.h

Quoted 8 lines

? Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be ? referred to.

- Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE

? This is something suggested by Wolfgang, and for automatic ? calculation of macros like CONFIG_SYS_GBL_DATA_SIZE (done) and ? CONFIG_SYS_INIT_SP_ADDR (later).

Um... this is NOT what we discussed.

Review

Quoted 6 lines
(quoted diff) +6 -0
+#define CONFIG_SYS_SDRAM_BASE ? ? ? ? ? ? ? ?(PHYS_SDRAM_1)
+#define CONFIG_SYS_INIT_RAM_ADDR ? ? (IRAM_BASE_ADDR)
+#define CONFIG_SYS_INIT_RAM_SIZE ? ? (IRAM_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR ? ? ?\
+ ? ? (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE)
+

No. ?This is not what I want to se.

Quoted 7 lines

Memory allocation in the inital ram has the global data at the top.

Please use something like

#define CONFIG_SYS_INIT_SP_OFFSET ?(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_ADDR ? ?(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

It ends up with the following compiling error.

start.S:175: Error: garbage following instruction -- `ldr sp,=(((0x1FFE0000)+((0x00020000)-#96)))'

Can we just go the current way for the near term, and wait for the auto calculation to clean it up?

Signature · 2 lines
Regards,
Shawn
#12 lore raw

PATCH v2 1/1 mx51evk: support new relocation scheme

Dear Shawn Guo,

Quoted 8 lines · In message <[email protected]> you…

It ends up with the following compiling error.

start.S:175: Error: garbage following instruction -- `ldr sp,=(((0x1FFE0000)+((0x00020000)-#96)))'

Can we just go the current way for the near term, and wait for the auto calculation to clean it up?

This has been fixed - see
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/87669

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
I'd like to meet the man who invented sex and see what  he's  working
on now.
#13 lore raw

PATCH v3 1/1 mx51evk: support new relocation scheme

In reply to Shawn Guo

From: Shawn Guo <[email protected]>

This patch is to fix build breakage and support new relocation scheme for mx51evk.

- Correct IRAM base address and add size definition

The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than 0x1FFE8000 which is for older revision.

- Include imx-regs.h in mx51evk.h

Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be referred to.

- Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE

They are used to define init RAM layout.

- Remove comment for CONFIG_SYS_GBL_DATA_SIZE which has been buried by Wolfgang's commit below

25ddd1fb: Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

---
Changes for v3:
- Correct init RAM layout to have global data at the top.

Changes for v2:
- Combine two patches before into one, as the separation is not so logical.
- Define init stack at the end of init RAM to address comments from Stefano, Heiko and Wolfgang.

 arch/arm/include/asm/arch-mx5/imx-regs.h |    3 ++-
 board/freescale/mx51evk/mx51evk.c        |    6 +++---
 include/configs/mx51evk.h                |   12 ++++++++++--
 3 files changed, 15 insertions(+), 6 deletions(-)
arch/arm/include/asm/arch-mx5/imx-regs.h +2 -1
index 3ddda40..0b6249a 100644
@@ -26,7 +26,8 @@
 /*
  * IRAM
  */
-#define IRAM_BASE_ADDR		0x1FFE8000	/* internal ram */
+#define IRAM_BASE_ADDR		0x1FFE0000	/* internal ram */
+#define IRAM_SIZE		0x00020000	/* 128 KB */
 /*
  * Graphics Memory of GPU
  */
board/freescale/mx51evk/mx51evk.c +3 -3
index c8d7d39..8820698 100644
@@ -52,9 +52,9 @@ u32 get_board_rev(void)
 
 int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1,
-			PHYS_SDRAM_1_SIZE);
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_1_SIZE);
 	return 0;
 }
 
include/configs/mx51evk.h +10 -2
index f31fc4e..6282467 100644
@@ -24,11 +24,11 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#include <asm/arch/imx-regs.h>
 
  /* High Level Configuration Options */
 
 #define CONFIG_MX51	/* in a mx51 */
-#define CONFIG_SKIP_RELOCATE_UBOOT
 
 #define CONFIG_SYS_MX5_HCLK	24000000
 #define CONFIG_SYS_MX5_CLK32		32768
@@ -51,7 +51,6 @@
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2 * 1024 * 1024)
-/* size in bytes reserved for initial data */
 
 #define BOARD_LATE_INIT
 
@@ -174,6 +173,15 @@
 #define PHYS_SDRAM_1		CSD0_BASE_ADDR
 #define PHYS_SDRAM_1_SIZE	(512 * 1024 * 1024)
 
+#define CONFIG_SYS_SDRAM_BASE		(PHYS_SDRAM_1)
+#define CONFIG_SYS_INIT_RAM_ADDR	(IRAM_BASE_ADDR)
+#define CONFIG_SYS_INIT_RAM_SIZE	(IRAM_SIZE)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
 #define CONFIG_SYS_DDR_CLKSEL	0
 #define CONFIG_SYS_CLKTL_CBCDR	0x59E35100
 
Signature · 1 line
1.7.1
#14 lore raw

PATCH v3 1/1 mx51evk: support new relocation scheme

Quoted 17 lines · Shawn.Guo at freescale.com

From: Shawn Guo <[email protected]>

This patch is to fix build breakage and support new relocation scheme for mx51evk.

- Correct IRAM base address and add size definition

The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than 0x1FFE8000 which is for older revision.

- Include imx-regs.h in mx51evk.h

Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be referred to.

- Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE

Quoted 8 lines

They are used to define init RAM layout.

- Remove comment for CONFIG_SYS_GBL_DATA_SIZE which has been buried by Wolfgang's commit below

25ddd1fb: Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================