Skip to contentSkip to conversation

Question/help re: themake scripts in 2.6.36

DISCUSSION JD 2 participants 3 messages Nov 7, 2010 – Nov 9, 2010 1 message not in the archive

lore
Share & tools
lore

JD

author
#0 lore raw

I have compiled 2.6.36 (i686) without any problems. Since then, I have decided to change a couple of config variables (using xconfig).
When done, running make all
causes the make scripts to stop compilation after building a few objects, and spawn a shell.
Since I have no idea what to do in that shell, I exit that shell, and the compilaton continues.
This takes place 3 times before compilation is complete.

Now, when I type make modules_install install,
only modules_install is done. /boot does not get
populated and /boot/grub/grub.conf is unchanged.

The currently installed and running 2.6.36-1
went through a similar scenario during build,
but at least install did work.
Now the install does not work.
Befor the present build attempt,
I had edited the Makefile to change the EXTRAVERSION to -2 in order not to clobber the installed 2.6.36-1

Could someone tell me what to do to force the install in /boot? /lib/modules does have 2.6.36-2.fc13.i686 fully populated.

Thanx,

JD

#1 lore raw
Quoted 3 lines · JD

I have compiled 2.6.36 (i686) without any problems. Since then, I have decided to change a couple of config variables (using xconfig).

You can use 'make oldconfig'.

Quoted 7 lines

When done, running make all
causes the make scripts to stop compilation after building a few objects, and spawn a shell.
Since I have no idea what to do in that shell, I exit that shell, and the compilaton continues.
This takes place 3 times before compilation is complete.

What? How can make spawn a shell...

Can you copy and paste what you see and what you get from your terminal?

Quoted 12 lines

Now, when I type make modules_install install,
only modules_install is done. /boot does not get
populated and /boot/grub/grub.conf is unchanged.

The currently installed and running 2.6.36-1
went through a similar scenario during build,
but at least install did work.
Now the install does not work.
Befor the present build attempt,
I had edited the Makefile to change the EXTRAVERSION to -2 in order not to clobber the installed 2.6.36-1

Quoted 3 lines

Could someone tell me what to do to force the install in /boot? /lib/modules does have 2.6.36-2.fc13.i686 fully populated.

Since you are using Fedora, you can try grubby or new-kernel-pkg.

Signature · 1 line
Live like a child, think like the god.

A message that is not in the archive (sent off-list or not yet received): [email protected]

#3 lore raw
Quoted 18 lines · JD
Quoted 17 lines · Américo Wang
Quoted 3 lines · JD

I have compiled 2.6.36 (i686) without any problems. Since then, I have decided to change a couple of config variables (using xconfig).

You can use 'make oldconfig'.

Quoted 7 lines

When done, running make all
causes the make scripts to stop compilation after building a few objects, and spawn a shell.
Since I have no idea what to do in that shell, I exit that shell, and the compilaton continues.
This takes place 3 times before compilation is complete.

What? How can make spawn a shell...

Quoted 9 lines
Quoted 2 lines

Can you copy and paste what you see and what you get from your terminal?

I have attached make.out.xz
(compressed with lzma).

Look for exit
because I had to exit the shell that gets forked in order to let make continue.

Well, that is not due to make, it is because you
used su -c 'make install modules_install'. :)

Try su -c 'make install && make modules_install'.