Skip to contentSkip to conversation

Patch IMX audmux debugfs.

PATCH New Bill Pringlemeir 4 participants 16 messages Nov 9, 2010 – Nov 30, 2010 5 messages not in the archive

Subsystems (3)
lore
Share & tools
lore
#0 lore raw
$ mount -t debugfs debugfs /sys/kernel/debug
$ cd /sys/kernel/debug/audmux
$ cat *
[crashes when accessing ssi7]

The index is one based, but the register map is zero based. So the ssi1 is actually sending info for ssi2. Also, the ssi7 touches non-existent data and can cause an exception (only registers sets 1-6 exist).

Alternatively, the MX31_AUDMUX_PORT6_SSI_PINS_6 and MX27_AUDMUX_PPCR3_SSI_PINS_3 constants could be used for the loop termination, but maybe that means conditionalization (and there are no MX25 constants).

arch/arm/plat-mxc/audmux-v2.c +2 -2
index f9e7cdb..0547145 100644
@@ -66,7 +66,7 @@ static ssize_t audmux_read_file(struct file *file, char __user *user_buf,
 {
        ssize_t ret;
        char *buf = kmalloc(PAGE_SIZE, GFP_KERNEL);
-       int port = (int)file->private_data;
+       int port = ((int)file->private_data) - 1;
        u32 pdcr, ptcr;
 
        if (!buf)
@@ -150,7 +150,7 @@ static void audmux_debugfs_init(void)
                return;
        }
 
-       for (i = 1; i < 8; i++) {
+       for (i = 1; i < 7; i++) {
                snprintf(buf, sizeof(buf), "ssi%d", i);
                if (!debugfs_create_file(buf, 0444, audmux_debugfs_root,
                                         (void *)i, &audmux_debugfs_fops))
#1 lore raw

Hello.

Quoted 20 lines · Bill Pringlemeir
$ mount -t debugfs debugfs /sys/kernel/debug
$ cd /sys/kernel/debug/audmux
$ cat *
[crashes when accessing ssi7]

The index is one based, but the register map is zero based. So the ssi1 is actually sending info for ssi2. Also, the ssi7 touches non-existent data and can cause an exception (only registers sets 1-6 exist).

Alternatively, the MX31_AUDMUX_PORT6_SSI_PINS_6 and MX27_AUDMUX_PPCR3_SSI_PINS_3 constants could be used for the loop termination, but maybe that means conditionalization (and there are no MX25 constants).

arch/arm/plat-mxc/audmux-v2.c +0 -0
index f9e7cdb..0547145 100644

arch/arm/plat-mxc/audmux-v2.c static ssize_t audmux_read_file(struct file *file, char __user *user_buf, · line 69

Quoted 5 lines
arch/arm/plat-mxc/audmux-v2.c +1 -1
@@ -66,7 +66,7 @@ static ssize_t audmux_read_file(struct file *file, char __user *user_buf,
  {
         ssize_t ret;
         char *buf = kmalloc(PAGE_SIZE, GFP_KERNEL);
-       int port = (int)file->private_data;
+       int port = ((int)file->private_data) - 1;

Parens around typecast not necessary.

WBR, Sergei

maintainer
#2 lore raw
In reply to Bill Pringlemeir

Hi Bill,

Quoted 30 lines · Bill Pringlemeir
$ mount -t debugfs debugfs /sys/kernel/debug
$ cd /sys/kernel/debug/audmux
$ cat *
[crashes when accessing ssi7]

The index is one based, but the register map is zero based. So the ssi1 is actually sending info for ssi2. Also, the ssi7 touches non-existent data and can cause an exception (only registers sets 1-6 exist).

Alternatively, the MX31_AUDMUX_PORT6_SSI_PINS_6 and MX27_AUDMUX_PPCR3_SSI_PINS_3 constants could be used for the loop termination, but maybe that means conditionalization (and there are no MX25 constants).

arch/arm/plat-mxc/audmux-v2.c +1 -1
index f9e7cdb..0547145 100644
@@ -66,7 +66,7 @@ static ssize_t audmux_read_file(struct file *file, char __user *user_buf,
 {
        ssize_t ret;
        char *buf = kmalloc(PAGE_SIZE, GFP_KERNEL);
-       int port = (int)file->private_data;
+       int port = ((int)file->private_data) - 1;
        u32 pdcr, ptcr;
 
        if (!buf)

arch/arm/plat-mxc/audmux-v2.c static void audmux_debugfs_init(void) · line 156

Quoted 8 lines
arch/arm/plat-mxc/audmux-v2.c +1 -1
@@ -150,7 +150,7 @@ static void audmux_debugfs_init(void)
                return;
        }
 
-       for (i = 1; i < 8; i++) {
+       for (i = 1; i < 7; i++) {
                snprintf(buf, sizeof(buf), "ssi%d", i);
                if (!debugfs_create_file(buf, 0444, audmux_debugfs_root,
                                         (void *)i, &audmux_debugfs_fops))

I prefer passing (void *)(i - 1) here and skipping the first hunk. Please add your Signed-off-by next time you send a patch.

Sascha

Signature · 4 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
#3 lore raw
Quoted 7 lines · s.hauer at pengutronix.de
Quoted 4 lines · Bill Pringlemeir
$ mount -t debugfs debugfs /sys/kernel/debug
$ cd /sys/kernel/debug/audmux
$ cat *
[crashes when accessing ssi7]
Quoted 7 lines
Quoted 4 lines

The index is one based, but the register map is zero based. So the ssi1 is actually sending info for ssi2. Also, the ssi7 touches non-existent data and can cause an exception (only registers sets 1-6 exist).

I prefer passing (void *)(i - 1) here and skipping the first hunk. Please add your Signed-off-by next time you send a patch.

Something similar occured in to me after reading Sergei message. This patch treats i as the port instead of the file name. The file name is generated from audmux_port_string making the filenames and file content the same.

arch/arm/plat-mxc/audmux-v2.c +3 -4
index f9e7cdb..ac30fdc 100644
@@ -142,7 +142,6 @@ static const struct file_operations audmux_debugfs_fops = {
 static void audmux_debugfs_init(void)
 {
        int i;
-       char buf[20];
 
        audmux_debugfs_root = debugfs_create_dir("audmux", NULL);
        if (!audmux_debugfs_root) {
@@ -150,9 +149,9 @@ static void audmux_debugfs_init(void)
                return;
        }
 
-       for (i = 1; i < 8; i++) {
-               snprintf(buf, sizeof(buf), "ssi%d", i);
-               if (!debugfs_create_file(buf, 0444, audmux_debugfs_root,
+       for (i = 0; i < 6; i++) {
+               if (!debugfs_create_file(audmux_port_string(i), 0444,
+                                        audmux_debugfs_root,
                                         (void *)i, &audmux_debugfs_fops))
                        pr_warning("Failed to create AUDMUX port %d debugfs file\n",
                                   i);
maintainer
#4 lore raw
Quoted 14 lines · Bill Pringlemeir
Quoted 11 lines · s.hauer at pengutronix.de
Quoted 9 lines · Bill Pringlemeir
$ mount -t debugfs debugfs /sys/kernel/debug
$ cd /sys/kernel/debug/audmux
$ cat *
[crashes when accessing ssi7]

The index is one based, but the register map is zero based. So the ssi1 is actually sending info for ssi2. Also, the ssi7 touches non-existent data and can cause an exception (only registers sets 1-6 exist).

Quoted 7 lines
Quoted 2 lines

I prefer passing (void *)(i - 1) here and skipping the first hunk. Please add your Signed-off-by next time you send a patch.

Something similar occured in to me after reading Sergei message. This patch treats i as the port instead of the file name. The file name is generated from audmux_port_string making the filenames and file content the same.

Ok, looks sensible to me. I added Mark Brown to Cc as he added the debugfs support in the first place. Maybe he has some comment to add.

Sascha

Quoted 28 lines
arch/arm/plat-mxc/audmux-v2.c +3 -4
index f9e7cdb..ac30fdc 100644
@@ -142,7 +142,6 @@ static const struct file_operations audmux_debugfs_fops = {
 static void audmux_debugfs_init(void)
 {
        int i;
-       char buf[20];
 
        audmux_debugfs_root = debugfs_create_dir("audmux", NULL);
        if (!audmux_debugfs_root) {
@@ -150,9 +149,9 @@ static void audmux_debugfs_init(void)
                return;
        }
 
-       for (i = 1; i < 8; i++) {
-               snprintf(buf, sizeof(buf), "ssi%d", i);
-               if (!debugfs_create_file(buf, 0444, audmux_debugfs_root,
+       for (i = 0; i < 6; i++) {
+               if (!debugfs_create_file(audmux_port_string(i), 0444,
+                                        audmux_debugfs_root,
                                         (void *)i, &audmux_debugfs_fops))
                        pr_warning("Failed to create AUDMUX port %d debugfs file\n",
                                   i);
Signature · 4 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
#5 lore raw
Quoted 2 lines · Sascha Hauer

Ok, looks sensible to me. I added Mark Brown to Cc as he added the debugfs support in the first place. Maybe he has some comment to add.

Not really, except that the numbers used correspond to the numbers used by the audmux APIs in the kernel IIRC.

#6 lore raw

On 12 Nov 2010, broonie at opensource.wolfsonmicro.com wrote:

Quoted 5 lines · Sascha Hauer
Quoted 2 lines

Ok, looks sensible to me. I added Mark Brown to Cc as he added the debugfs support in the first place. Maybe he has some comment to add.

Not really, except that the numbers used correspond to the numbers used by the audmux APIs in the kernel IIRC.

I guess that was non-obvious as 'port 0' (corresponding to imx-ssi.0) has no associated file in the current code. I can re-submit a patch with just this correction; add SSI0 and remove SSI6, SSI7 files.

However, as someone who is/was debugging an SOC audio system and stumbled upon this debugfs entry, I don't think those numbers are apparently obvious even with the fix. I think both Sascha and I had thought SSI1 corresponded to what should have been SSI0 (er, maybe I lead Sascha that way). I still think that having the 'port/channel' name used in the file correspond to the the actual file names is probably at least as debugfs user friendly. The files names/content are being viewed together so consistency seems in order.

Also, the kernel numbers *can* be referred to by macros and some users might not even realize these numbers exist. In any case, I would have probably clued in if SSI0 had existed. So I will fix that if we want to remain with it? The first patch submitted didn't do this.

Regards,
Bill Pringlemeir.

A message that is not in the archive (sent off-list or not yet received): [email protected]

#8 lore raw

PATCH v3 1/1 Fix audmuxv2 debugfs indexing. [was: Patch IMX audmux debugfs.]

On 14 Nov 2010, bpringle at sympatico.ca wrote:
On 12 Nov 2010, broonie at opensource.wolfsonmicro.com wrote:

Quoted 5 lines · Sascha Hauer
Quoted 5 lines
Quoted 2 lines

Ok, looks sensible to me. I added Mark Brown to Cc as he added the debugfs support in the first place. Maybe he has some comment to add.

Not really, except that the numbers used correspond to the numbers used by the audmux APIs in the kernel IIRC.

[snip]

Quoted 4 lines

Also, the kernel numbers *can* be referred to by macros and some users might not even realize these numbers exist. In any case, I would have probably clued in if SSI0 had existed. So I will fix that if we want to remain with it? The first patch submitted didn't do this.

Following is the simple patch which corrects improper file indexing of audmux port numbers. Ie, ssi6, ssi7. It also adds the ssi0 file. The directory looks like this,

root at uclibc /sys/kernel/debug/audmux$ ls
ssi0 ssi1 ssi2 ssi3 ssi4 ssi5

With the number in ssi[0-5], corresponding to the 'MX31_AUDMUX_PORT[1-6]_*' and 'MX27_AUDMUX_[PH]PCR[1-3]_*' in audmux.h or the raw value of the 'port' parameter of mxc_audmux_v2_configure_port().

arch/arm/plat-mxc/audmux-v2.c +1 -1
index f9e7cdb..2a1021f 100644
@@ -150,7 +150,7 @@ static void audmux_debugfs_init(void)
                return;
        }
 
-       for (i = 1; i < 8; i++) {
+       for (i = 0; i < 6; i++) {
                snprintf(buf, sizeof(buf), "ssi%d", i);
                if (!debugfs_create_file(buf, 0444, audmux_debugfs_root,
                                         (void *)i, &audmux_debugfs_fops))
#9 lore raw

PATCH v3 1/1 Fix audmuxv2 debugfs indexing. [was: Patch IMX audmux debugfs.]

arch/arm/plat-mxc/audmux-v2.c static void audmux_debugfs_init(void) · line 156

Quoted 5 lines · Bill Pringlemeir
arch/arm/plat-mxc/audmux-v2.c +1 -1
-       for (i = 1; i < 8; i++) {
+       for (i = 0; i < 6; i++) {
                snprintf(buf, sizeof(buf), "ssi%d", i);
                if (!debugfs_create_file(buf, 0444, audmux_debugfs_root,
                                         (void *)i, &audmux_debugfs_fops))

We appear to have misplaced a SSI port here...

#10 lore raw

PATCH v3 1/1 Fix audmuxv2 debugfs indexing.

On 15 Nov 2010, broonie at opensource.wolfsonmicro.com wrote:

Quoted 7 lines · Bill Pringlemeir
Quoted 5 lines
arch/arm/plat-mxc/audmux-v2.c +1 -1
-       for (i = 1; i < 8; i++) {
+       for (i = 0; i < 6; i++) {

snprintf(buf, sizeof(buf), "ssi%d", i);
if (!debugfs_create_file(buf, 0444, audmux_debugfs_root, (void *)i, &audmux_debugfs_fops))

We appear to have misplaced a SSI port here...

Hmm, that is right. SSI6 was returning bogus data (inside the debugfs file "UNKNOWN" occured)... Maybe it is just never setup right. I will look.

Signature · 1 line
Yow!  Legally-imposed CULTURE-reduction is CABBAGE-BRAINED!

A message that is not in the archive (sent off-list or not yet received): [email protected]

#12 lore raw

PATCH v3 1/1 Fix audmuxv2 debugfs indexing.

On 15 Nov 2010, bpringle at sympatico.ca wrote:
On 15 Nov 2010, broonie at opensource.wolfsonmicro.com wrote:

Quoted 11 lines · Bill Pringlemeir
Quoted 7 lines
Quoted 5 lines
arch/arm/plat-mxc/audmux-v2.c +1 -1
-       for (i = 1; i < 8; i++) {
+       for (i = 0; i < 6; i++) {

snprintf(buf, sizeof(buf), "ssi%d", i);
if (!debugfs_create_file(buf, 0444, audmux_debugfs_root, (void *)i, &audmux_debugfs_fops))

We appear to have misplaced a SSI port here...

Hmm, that is right. SSI6 was returning bogus data (inside the debugfs file "UNKNOWN" occured)... Maybe it is just never setup right. I will look.

I had thought the audmux_port_string() was correct and 'SSI6' was looking at some 'bad memory'.

Sorry, I should have waited to email. audmux_port_string() only handles six values (not seven). Also, the audmux.h only has six defines for both MX31 and MX27. There isn't an SSI7 that is being reported by the debugfs. However, a user of the audmux-v2.c code can call mxc_audmux_v2_configure_port() with a port value of '6' to configure audmux pin set 7 ;-)

The documentation we are working with isn't that helpful. For the iMx 25 pg 13-4, it says there are "Three internal ports", but I can only find two ssi devices (with two channels of audio each)...

fwiw,
Bill Pringlemeir.

#13 lore raw

PATCH v3 1/1 Fix audmuxv2 debugfs indexing.

Quoted 6 lines · Bill Pringlemeir

Sorry, I should have waited to email. audmux_port_string() only handles six values (not seven). Also, the audmux.h only has six defines for both MX31 and MX27. There isn't an SSI7 that is being reported by the debugfs. However, a user of the audmux-v2.c code can call mxc_audmux_v2_configure_port() with a port value of '6' to configure audmux pin set 7 ;-)

SSI7 is an internal network connection thing of some kind.

Quoted 3 lines

The documentation we are working with isn't that helpful. For the iMx 25 pg 13-4, it says there are "Three internal ports", but I can only find two ssi devices (with two channels of audio each)...

It's not an SSI port.

#14 lore raw

PATCH v3 1/1 Fix audmuxv2 debugfs indexing.

On 15 Nov 2010, broonie at opensource.wolfsonmicro.com wrote:

Quoted 8 lines · Bill Pringlemeir
Quoted 6 lines

Sorry, I should have waited to email. audmux_port_string() only handles six values (not seven). Also, the audmux.h only has six defines for both MX31 and MX27. There isn't an SSI7 that is being reported by the debugfs. However, a user of the audmux-v2.c code can call mxc_audmux_v2_configure_port() with a port value of '6' to configure audmux pin set 7 ;-)

SSI7 is an internal network connection thing of some kind.

On pg 4-60 of the IMX 25 reference manual, the IOMUX configuration for ALT3 is AUD7_TXFS. This makes me think it is a 'physical' pin after the IOMUX routing.

 $ grep AUD7 arch/arm/plat-mxc/include/mach/iomux-mx25.h
    364:#define MX25_PAD_SD1_DATA1__AUD7_RXD  
    469:#define MX25_PAD_GPIO_E__AUD7_TXD     
    472:#define MX25_PAD_GPIO_F__AUD7_TXC     
    481:#define MX25_PAD_VSTBY_REQ__AUD7_TXFS 
    487:#define MX25_PAD_POWER_FAIL__AUD7_RXD 

Oddly, the iomux-mx25.h is the only 'iomux-mx[1235]*.h' one with this audmux 7 configuration, but some of the ALT configuration values are missing from these files. Maybe the MX25 is different. It is the only IMX processor that I am familar with.

'iomux-mx25.h' has

     77:#define MX25_PAD_EB0__AUD4_TXD         
     81:#define MX25_PAD_EB1__AUD4_RXD         
     85:#define MX25_PAD_OE__AUD4_TXC          
    117:#define MX25_PAD_RW__AUD4_TXFS         
    364:#define MX25_PAD_SD1_DATA1__AUD7_RXD   
    394:#define MX25_PAD_KPP_COL0__AUD5_TXD    
    399:#define MX25_PAD_KPP_COL1__AUD5_RXD    
    404:#define MX25_PAD_KPP_COL2__AUD5_TXC    
    409:#define MX25_PAD_KPP_COL3__AUD5_TXFS   
    413:#define MX25_PAD_FEC_MDC__AUD4_TXD     
    417:#define MX25_PAD_FEC_MDIO__AUD4_RXD    
    424:#define MX25_PAD_FEC_TDATA1__AUD4_TXFS 
    469:#define MX25_PAD_GPIO_E__AUD7_TXD      
    472:#define MX25_PAD_GPIO_F__AUD7_TXC      
    481:#define MX25_PAD_VSTBY_REQ__AUD7_TXFS  
    487:#define MX25_PAD_POWER_FAIL__AUD7_RXD  

As well, chapter 4 (IOMUX) of the IMX25 RM has,

LD8, ALT4 -> AUD3_TXD
LD9, ALT4 -> AUD3_RXD
LD10, ALT4 -> AUD3_TXC
LD11, ALT4 -> AUD3_TXFS
LD14, ALT6 -> AUD3_RXC
LD15, ALT6 -> AUD3_RXFS

CSID8, ALT2 -> AUD6_RXC
... etc.

Quoted 5 lines
Quoted 3 lines

The documentation we are working with isn't that helpful. For the iMx 25 pg 13-4, it says there are "Three internal ports", but I can only find two ssi devices (with two channels of audio each)...

It's not an SSI port.

No, I don't think it is an SSI protocol device either. I think there are two internal ports and five external ports, at least on the IMX
25. Maybe the documentation is cut and paste from another processor?

There is this cryptic section of the on pg 13-4,

13.2 External Signal Description

Table 13-2 lists AUDMUX pin-level signals for the external ports, where:

? Pn is P4, through P7
? m = n ? 3.

The port is configured as an external port by a static system-level signal input pn_int_ext_select.

I guess they could be 'internal' if you didn't configure an external pin with the iomux module. Register IOMUXC_AUDMUX_P4_INPUT_DA_AMX_SELECT_INPUT (offset 0x460) might be what the above section refers to, but this involves 'daisy chaining' and only AUDMUX_P4 and AUDMUX_P7 are listed here (No P3,P5,P6).

Thanks for you help. I *think* I am getting closer to understanding this now.

Regards,
Bill Pringlemeir.

Signature · 1 line
Someday we'll look back on all this and plow into a parked car.

A message that is not in the archive (sent off-list or not yet received): [email protected]

#16 lore raw

PATCH v3 1/1 Fix audmuxv2 debugfs indexing.

Quoted 3 lines · bpringle at sympatico.ca

No, I don't think it is an SSI protocol device either. I think there are two internal ports and five external ports, at least on the IMX
25. Maybe the documentation is cut and paste from another processor?

[snip]

Quoted 2 lines

Thanks for you help. I *think* I am getting closer to understanding this now.

I sent a service request to Freescale,

[Technical Support Freescale Semiconductor]

In reply to your Service Request SR 1-694170620: The i.MX25 AUDMUX Port1 and Port2 are connected to the internal SSI modules, the Port3 to Port7 are connected to external pins through the IOMUX module. The Port7 can be always used as external port, regardless of the CE bus mode. Should you need to contact us with regard to this message, please see the notes below.

It looks like the i.MX25 is a mix of the i.MX31 and i.MX35. I think it makes the most sense to change the audmux_port_string() to return "SSI7" instead of "UNKNOWN" for this port and fix the loop indexes.

I will re-submit those patches later.

Regards,
Bill Pringlemeir.

A message that is not in the archive (sent off-list or not yet received): [email protected]

#18 lore raw

PATCH v3 1/1 Fix audmuxv2 debugfs indexing.

Quoted 1 line · bpringle at sympatico.ca

I will re-submit those patches later.

Here is the audmux debug directory after this patch,

root at freescale /sys/kernel/debug/audmux$ ls
SSI3 SSI4 SSI5 SSI6 SSI7 imx-ssi.0 imx-ssi.1
root at freescale /sys/kernel/debug/audmux$ cat SSI7
PDCR: 0000c000
PTCR: 00000800
TxFS input, TxClk input
Port is symmetric
Data received from SSI7

The ugly part is 'case 6:'. However, there currently is no constants defined in audmux.h for this port. Also, mxc_audmux_v2_configure_port() isn't protecting against ports out of range and there are no constants for the IMX25. I would need answers to what should be done to invent a define for 'port 6 (SSI7)'. Using MX31 constants seems incomplete as this code could be active for an MX35 and MX25 as well.

arch/arm/plat-mxc/audmux-v2.c +5 -4
index f9e7cdb..205de57 100644
@@ -56,6 +56,8 @@ static const char *audmux_port_string(int port)
                return "SSI5";
        case MX31_AUDMUX_PORT6_SSI_PINS_6:
                return "SSI6";
+       case 6: /* internal or pins AUDMUX_PORT7 */
+               return "SSI7";
        default:
                return "UNKNOWN";
        }
@@ -142,7 +144,6 @@ static const struct file_operations audmux_debugfs_fops = {
 static void audmux_debugfs_init(void)
 {
        int i;
-       char buf[20];
 
        audmux_debugfs_root = debugfs_create_dir("audmux", NULL);
        if (!audmux_debugfs_root) {
@@ -150,9 +151,9 @@ static void audmux_debugfs_init(void)
                return;
        }
 
-       for (i = 1; i < 8; i++) {
-               snprintf(buf, sizeof(buf), "ssi%d", i);
-               if (!debugfs_create_file(buf, 0444, audmux_debugfs_root,
+       for (i = 0; i < 7; i++) {
+               if (!debugfs_create_file(audmux_port_string(i), 0444,
+                                        audmux_debugfs_root,
                                         (void *)i, &audmux_debugfs_fops))
                        pr_warning("Failed to create AUDMUX port %d debugfs file\n",
                                   i);

A message that is not in the archive (sent off-list or not yet received): [email protected]

#20 lore raw

PATCH v3 1/1 Fix audmuxv2 debugfs indexing.

Quoted 6 lines · bpringle at sympatico.ca

Following is the simple patch which corrects improper file indexing of audmux port numbers. Ie, ssi6, ssi7. It also adds the ssi0 file. The directory looks like this,

root at uclibc /sys/kernel/debug/audmux$ ls
ssi0 ssi1 ssi2 ssi3 ssi4 ssi5

The attached incremental patch changes the audmux v2 file naming to correspond to the names used within the file.

root at uclibc /sys/kernel/debug/audmux$ ls
SSI3 SSI4 SSI5 SSI6 imx-ssi.0 imx-ssi.1

root at uclibc /sys/kernel/debug/audmux$ cat imx-ssi.1
PDCR: 00008000
PTCR: a5000800
TxFS output from SSI5, TxClk output from SSI5 Port is symmetric
Data received from SSI5

The file 'imx-ssi.1' was 'ssi1'. Here, the imx-ssi.1 driver is connected to audmux pin set 5. Perhaps 'audmux[3-5]' are better names than SSI[3-5], if we are updating the naming scheme. I think the upper case names shout hardware loud enough.

arch/arm/plat-mxc/audmux-v2.c +2 -3
index 2a1021f..8157704 100644
@@ -142,7 +142,6 @@ static const struct file_operations audmux_debugfs_fops = {
 static void audmux_debugfs_init(void)
 {
        int i;
-       char buf[20];
 
        audmux_debugfs_root = debugfs_create_dir("audmux", NULL);
        if (!audmux_debugfs_root) {
@@ -151,8 +150,8 @@ static void audmux_debugfs_init(void)
        }
 
        for (i = 0; i < 6; i++) {
-               snprintf(buf, sizeof(buf), "ssi%d", i);
-               if (!debugfs_create_file(buf, 0444, audmux_debugfs_root,
+               if (!debugfs_create_file(audmux_port_string(i), 0444,
+                                        audmux_debugfs_root,
                                         (void *)i, &audmux_debugfs_fops))
                        pr_warning("Failed to create AUDMUX port %d debugfs file\n",
                                   i);