Skip to contentSkip to conversation

ARM: Common GIC entry macro code V3

PATCH In review Magnus Damm 5 participants 12 messages Nov 12, 2010

Subsystems (6)
lore
Share & tools
lore
#0 lore raw

cover ARM: Common GIC entry macro code V3

ARM: Common GIC entry macro code V3

[PATCH 01/07] ARM: Introduce asm/hardware/entry-macro-gic.S [PATCH 02/07] ARM: Use shared GIC entry macros on CNS3XXX [PATCH 03/07] ARM: Use shared GIC entry macros on Realview [PATCH 04/07] ARM: Use shared GIC entry macros on Tegra [PATCH 05/07] ARM: Use shared GIC entry macros on UX500 [PATCH 06/07] ARM: Use shared GIC entry macros on Vexpress [PATCH 07/07] ARM: Use shared GIC entry macros on OMAP

Put GIC demux code in a common place to avoid duplicated code.

These patches are almost identical to 6284/1 in the RMKs patch tracker. The main difference is that these ones require each platform to specify base address using the macro get_irqnr_preable. Both Tegra and OMAP are supported in V3.

The s5pv310 subarch is excluded due to the special "addne" instruction in the get_irqnr_and_base macro.

The msm subarch is excluded as well since it treats PPIs differently than other platforms and needs a different version of the get_irqnr_and_base macro.

I intend to submit these patches to the RMK patch tracker unless I hear any objections.

---

 arch/arm/include/asm/hardware/entry-macro-gic.S   |   68 +++++++++++++++
 arch/arm/mach-cns3xxx/include/mach/entry-macro.S  |   61 -------------
 arch/arm/mach-omap2/include/mach/entry-macro.S    |   92 +++++++--------------
 arch/arm/mach-realview/include/mach/entry-macro.S |   60 -------------
 arch/arm/mach-tegra/include/mach/entry-macro.S    |   64 --------------
 arch/arm/mach-ux500/include/mach/entry-macro.S    |   67 ---------------
 arch/arm/mach-vexpress/include/mach/entry-macro.S |   57 -------------
 7 files changed, 104 insertions(+), 365 deletions(-)
#1 lore raw

PATCH 1/7 ARM: Introduce asm/hardware/entry-macro-gic.S

From: Magnus Damm <[email protected]>

This patch is the identical GIC demux implementation merge V3. Instead of implementing same code over and over simply share it in entry-macro-gic.S. The shared code is based on the realview implementation.

Each GIC demux instance still has to setup the base address of the controller using the get_irqnr_preamble macro. The rest of the GIC specific code can be shared.

---

Changes since V2:
- broke out patches into base + per sub-arch

 arch/arm/include/asm/hardware/entry-macro-gic.S |   68 +++++++++++++++++++++++
 1 file changed, 68 insertions(+)
arch/arm/include/asm/hardware/entry-macro-gic.S new file +68 -0
@@ -0,0 +1,68 @@
+/*
+ * arch/arm/include/asm/hardware/entry-macro-gic.S
+ *
+ * Low-level IRQ helper macros for GIC
+ *
+ * This file is licensed under  the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <asm/hardware/gic.h>
+
+/*
+ * The interrupt numbering scheme is defined in the
+ * interrupt controller spec.  To wit:
+ *
+ * Interrupts 0-15 are IPI
+ * 16-28 are reserved
+ * 29-31 are local.  We allow 30 to be used for the watchdog.
+ * 32-1020 are global
+ * 1021-1022 are reserved
+ * 1023 is "spurious" (no interrupt)
+ *
+ * For now, we ignore all local interrupts so only return an interrupt if it's
+ * between 30 and 1020.  The test_for_ipi routine below will pick up on IPIs.
+ *
+ * A simple read from the controller will tell us the number of the highest
+ * priority enabled interrupt.  We then just need to check whether it is in the
+ * valid range for an IRQ (30-1020 inclusive).
+ */
+
+	.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
+
+	ldr     \irqstat, [\base, #GIC_CPU_INTACK]
+	/* bits 12-10 = src CPU, 9-0 = int # */
+
+	ldr	\tmp, =1021
+	bic     \irqnr, \irqstat, #0x1c00
+	cmp     \irqnr, #29
+	cmpcc	\irqnr, \irqnr
+	cmpne	\irqnr, \tmp
+	cmpcs	\irqnr, \irqnr
+	.endm
+
+/* We assume that irqstat (the raw value of the IRQ acknowledge
+ * register) is preserved from the macro above.
+ * If there is an IPI, we immediately signal end of interrupt on the
+ * controller, since this requires the original irqstat value which
+ * we won't easily be able to recreate later.
+ */
+
+	.macro test_for_ipi, irqnr, irqstat, base, tmp
+	bic	\irqnr, \irqstat, #0x1c00
+	cmp	\irqnr, #16
+	strcc	\irqstat, [\base, #GIC_CPU_EOI]
+	cmpcs	\irqnr, \irqnr
+	.endm
+
+/* As above, this assumes that irqstat and base are preserved.. */
+
+	.macro test_for_ltirq, irqnr, irqstat, base, tmp
+	bic	\irqnr, \irqstat, #0x1c00
+	mov 	\tmp, #0
+	cmp	\irqnr, #29
+	moveq	\tmp, #1
+	streq	\irqstat, [\base, #GIC_CPU_EOI]
+	cmp	\tmp, #0
+	.endm
#2 lore raw

PATCH 2/7 ARM: Use shared GIC entry macros on CNS3XXX

In reply to Magnus Damm

From: Magnus Damm <[email protected]>

Use the GIC demux code in asm/hardware/entry-macro-gic.S on the CNS3XXX subarchitecture.

---

 arch/arm/mach-cns3xxx/include/mach/entry-macro.S |   61 ----------------------
 1 file changed, 1 insertion(+), 60 deletions(-)
arch/arm/mach-cns3xxx/include/mach/entry-macro.S +1 -60
@@ -9,7 +9,7 @@
  */
 
 #include <mach/hardware.h>
-#include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>
 
 		.macro	disable_fiq
 		.endm
@@ -21,62 +21,3 @@
 
 		.macro  arch_ret_to_user, tmp1, tmp2
 		.endm
-
-		/*
-		 * The interrupt numbering scheme is defined in the
-		 * interrupt controller spec.  To wit:
-		 *
-		 * Interrupts 0-15 are IPI
-		 * 16-28 are reserved
-		 * 29-31 are local.  We allow 30 to be used for the watchdog.
-		 * 32-1020 are global
-		 * 1021-1022 are reserved
-		 * 1023 is "spurious" (no interrupt)
-		 *
-		 * For now, we ignore all local interrupts so only return an interrupt if it's
-		 * between 30 and 1020.  The test_for_ipi routine below will pick up on IPIs.
-		 *
-		 * A simple read from the controller will tell us the number of the highest
-                 * priority enabled interrupt.  We then just need to check whether it is in the
-		 * valid range for an IRQ (30-1020 inclusive).
-		 */
-
-		.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-
-		ldr     \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */
-
-		ldr	\tmp, =1021
-
-		bic     \irqnr, \irqstat, #0x1c00
-
-		cmp     \irqnr, #29
-		cmpcc	\irqnr, \irqnr
-		cmpne	\irqnr, \tmp
-		cmpcs	\irqnr, \irqnr
-
-		.endm
-
-		/* We assume that irqstat (the raw value of the IRQ acknowledge
-		 * register) is preserved from the macro above.
-		 * If there is an IPI, we immediately signal end of interrupt on the
-		 * controller, since this requires the original irqstat value which
-		 * we won't easily be able to recreate later.
-		 */
-
-		.macro test_for_ipi, irqnr, irqstat, base, tmp
-		bic	\irqnr, \irqstat, #0x1c00
-		cmp	\irqnr, #16
-		strcc	\irqstat, [\base, #GIC_CPU_EOI]
-		cmpcs	\irqnr, \irqnr
-		.endm
-
-		/* As above, this assumes that irqstat and base are preserved.. */
-
-		.macro test_for_ltirq, irqnr, irqstat, base, tmp
-		bic	\irqnr, \irqstat, #0x1c00
-		mov 	\tmp, #0
-		cmp	\irqnr, #29
-		moveq	\tmp, #1
-		streq	\irqstat, [\base, #GIC_CPU_EOI]
-		cmp	\tmp, #0
-		.endm
#3 lore raw

PATCH 3/7 ARM: Use shared GIC entry macros on Realview

In reply to Magnus Damm

From: Magnus Damm <[email protected]>

Use the GIC demux code in asm/hardware/entry-macro-gic.S on the Realview subarchitecture.

---

 arch/arm/mach-realview/include/mach/entry-macro.S |   60 ---------------------
 1 file changed, 1 insertion(+), 59 deletions(-)
arch/arm/mach-realview/include/mach/entry-macro.S +1 -59
@@ -8,7 +8,7 @@
  * warranty of any kind, whether express or implied.
  */
 #include <mach/hardware.h>
-#include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>
 
 		.macro	disable_fiq
 		.endm
@@ -21,61 +21,3 @@
 		.macro  arch_ret_to_user, tmp1, tmp2
 		.endm
 
-		/*
-		 * The interrupt numbering scheme is defined in the
-		 * interrupt controller spec.  To wit:
-		 *
-		 * Interrupts 0-15 are IPI
-		 * 16-28 are reserved
-		 * 29-31 are local.  We allow 30 to be used for the watchdog.
-		 * 32-1020 are global
-		 * 1021-1022 are reserved
-		 * 1023 is "spurious" (no interrupt)
-		 *
-		 * For now, we ignore all local interrupts so only return an interrupt if it's
-		 * between 30 and 1020.  The test_for_ipi routine below will pick up on IPIs.
-		 *
-		 * A simple read from the controller will tell us the number of the highest
-                 * priority enabled interrupt.  We then just need to check whether it is in the
-		 * valid range for an IRQ (30-1020 inclusive).
-		 */
-
-		.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-
-		ldr     \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */
-
-		ldr	\tmp, =1021
-
-		bic     \irqnr, \irqstat, #0x1c00
-
-		cmp     \irqnr, #29
-		cmpcc	\irqnr, \irqnr
-		cmpne	\irqnr, \tmp
-		cmpcs	\irqnr, \irqnr
-
-		.endm
-
-		/* We assume that irqstat (the raw value of the IRQ acknowledge
-		 * register) is preserved from the macro above.
-		 * If there is an IPI, we immediately signal end of interrupt on the
-		 * controller, since this requires the original irqstat value which
-		 * we won't easily be able to recreate later.
-		 */
-
-		.macro test_for_ipi, irqnr, irqstat, base, tmp
-		bic	\irqnr, \irqstat, #0x1c00
-		cmp	\irqnr, #16
-		strcc	\irqstat, [\base, #GIC_CPU_EOI]
-		cmpcs	\irqnr, \irqnr
-		.endm
-
-		/* As above, this assumes that irqstat and base are preserved.. */
-
-		.macro test_for_ltirq, irqnr, irqstat, base, tmp
-		bic	\irqnr, \irqstat, #0x1c00
-		mov 	\tmp, #0
-		cmp	\irqnr, #29
-		moveq	\tmp, #1
-		streq	\irqstat, [\base, #GIC_CPU_EOI]
-		cmp	\tmp, #0
-		.endm
#4 lore raw

PATCH 4/7 ARM: Use shared GIC entry macros on Tegra

In reply to Magnus Damm

From: Magnus Damm <[email protected]>

Use the GIC demux code in asm/hardware/entry-macro-gic.S on the Tegra subarchitecture.

---

 arch/arm/mach-tegra/include/mach/entry-macro.S |   64 ------------------------
 1 file changed, 1 insertion(+), 63 deletions(-)
arch/arm/mach-tegra/include/mach/entry-macro.S +1 -63
@@ -17,7 +17,7 @@
 
 #if defined(CONFIG_ARM_GIC)
 
-#include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>
 
 	/* Uses the GIC interrupt controller built into the cpu */
 #define ICTRL_BASE (IO_CPU_VIRT + 0x100)
@@ -32,68 +32,6 @@
 
 	.macro  arch_ret_to_user, tmp1, tmp2
 	.endm
-
-	/*
-	 * The interrupt numbering scheme is defined in the
-	 * interrupt controller spec.  To wit:
-	 *
-	 * Interrupts 0-15 are IPI
-	 * 16-28 are reserved
-	 * 29-31 are local.  We allow 30 to be used for the watchdog.
-	 * 32-1020 are global
-	 * 1021-1022 are reserved
-	 * 1023 is "spurious" (no interrupt)
-	 *
-	 * For now, we ignore all local interrupts so only return an interrupt
-	 * if it's between 30 and 1020.  The test_for_ipi routine below will
-	 * pick up on IPIs.
-	 *
-	 * A simple read from the controller will tell us the number of the
-	 * highest priority enabled interrupt.  We then just need to check
-	 * whether it is in the valid range for an IRQ (30-1020 inclusive).
-	 */
-
-	.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-
-	/* bits 12-10 = src CPU, 9-0 = int # */
-	ldr     \irqstat, [\base, #GIC_CPU_INTACK]
-
-	ldr		\tmp, =1021
-
-	bic     \irqnr, \irqstat, #0x1c00
-
-	cmp     \irqnr, #29
-	cmpcc	\irqnr, \irqnr
-	cmpne	\irqnr, \tmp
-	cmpcs	\irqnr, \irqnr
-
-	.endm
-
-	/* We assume that irqstat (the raw value of the IRQ acknowledge
-	 * register) is preserved from the macro above.
-	 * If there is an IPI, we immediately signal end of interrupt on the
-	 * controller, since this requires the original irqstat value which
-	 * we won't easily be able to recreate later.
-	 */
-
-	.macro test_for_ipi, irqnr, irqstat, base, tmp
-	bic	\irqnr, \irqstat, #0x1c00
-	cmp	\irqnr, #16
-	strcc	\irqstat, [\base, #GIC_CPU_EOI]
-	cmpcs	\irqnr, \irqnr
-	.endm
-
-	/* As above, this assumes that irqstat and base are preserved.. */
-
-	.macro test_for_ltirq, irqnr, irqstat, base, tmp
-	bic	\irqnr, \irqstat, #0x1c00
-	mov 	\tmp, #0
-	cmp	\irqnr, #29
-	moveq	\tmp, #1
-	streq	\irqstat, [\base, #GIC_CPU_EOI]
-	cmp	\tmp, #0
-	.endm
-
 #else
 	/* legacy interrupt controller for AP16 */
 	.macro	disable_fiq
#6 lore raw

PATCH 5/7 ARM: Use shared GIC entry macros on UX500

In reply to Magnus Damm

From: Magnus Damm <[email protected]>

Use the GIC demux code in asm/hardware/entry-macro-gic.S on the UX500 subarchitecture.

---

 arch/arm/mach-ux500/include/mach/entry-macro.S |   67 ------------------------
 1 file changed, 1 insertion(+), 66 deletions(-)
arch/arm/mach-ux500/include/mach/entry-macro.S +1 -66
@@ -11,7 +11,7 @@
  * warranty of any kind, whether express or implied.
  */
 #include <mach/hardware.h>
-#include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>
 
 		.macro	disable_fiq
 		.endm
@@ -22,68 +22,3 @@
 
 		.macro  arch_ret_to_user, tmp1, tmp2
 		.endm
-
-		/*
-		 * The interrupt numbering scheme is defined in the
-		 * interrupt controller spec.  To wit:
-		 *
-		 * Interrupts 0-15 are IPI
-		 * 16-28 are reserved
-		 * 29-31 are local.  We allow 30 to be used for the watchdog.
-		 * 32-1020 are global
-		 * 1021-1022 are reserved
-		 * 1023 is "spurious" (no interrupt)
-		 *
-		 * For now, we ignore all local interrupts so only return an
-		 * interrupt if it's between 30 and 1020. The test_for_ipi
-		 * routine below will pick up on IPIs.
-		 *
-		 * A simple read from the controller will tell us the number
-		 * of the highest priority enabled interrupt. We then just
-		 * need to check whether it is in the valid range for an
-		 * IRQ (30-1020 inclusive).
-		 */
-
-		.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-
-		/* bits 12-10 = src CPU, 9-0 = int # */
-		ldr     \irqstat, [\base, #GIC_CPU_INTACK]
-
-		ldr	\tmp, =1021
-
-		bic     \irqnr, \irqstat, #0x1c00
-
-		cmp     \irqnr, #29
-		cmpcc	\irqnr, \irqnr
-		cmpne	\irqnr, \tmp
-		cmpcs	\irqnr, \irqnr
-
-		.endm
-
-		/* We assume that irqstat (the raw value of the IRQ
-		 * acknowledge register) is preserved from the macro above.
-		 * If there is an IPI, we immediately signal end of
-		 * interrupt on the controller, since this requires the
-		 * original irqstat value which we won't easily be able
-		 * to recreate later.
-		 */
-
-		.macro test_for_ipi, irqnr, irqstat, base, tmp
-		bic	\irqnr, \irqstat, #0x1c00
-		cmp	\irqnr, #16
-		strcc	\irqstat, [\base, #GIC_CPU_EOI]
-		cmpcs	\irqnr, \irqnr
-		.endm
-
-		/* As above, this assumes that irqstat and base
-		 * are preserved..
-		 */
-
-		.macro test_for_ltirq, irqnr, irqstat, base, tmp
-		bic	\irqnr, \irqstat, #0x1c00
-		mov 	\tmp, #0
-		cmp	\irqnr, #29
-		moveq	\tmp, #1
-		streq	\irqstat, [\base, #GIC_CPU_EOI]
-		cmp	\tmp, #0
-		.endm
#7 lore raw

PATCH 6/7 ARM: Use shared GIC entry macros on Vexpress

In reply to Magnus Damm

From: Magnus Damm <[email protected]>

Use the GIC demux code in asm/hardware/entry-macro-gic.S on the Versatile Express subarchitecture.

---

 arch/arm/mach-vexpress/include/mach/entry-macro.S |   57 ---------------------
 1 file changed, 1 insertion(+), 56 deletions(-)
arch/arm/mach-vexpress/include/mach/entry-macro.S +1 -56
@@ -1,4 +1,4 @@
-#include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>
 
 	.macro	disable_fiq
 	.endm
@@ -10,58 +10,3 @@
 
 	.macro	arch_ret_to_user, tmp1, tmp2
 	.endm
-
-	/*
-	 * The interrupt numbering scheme is defined in the
-	 * interrupt controller spec.  To wit:
-	 *
-	 * Interrupts 0-15 are IPI
-	 * 16-28 are reserved
-	 * 29-31 are local.  We allow 30 to be used for the watchdog.
-	 * 32-1020 are global
-	 * 1021-1022 are reserved
-	 * 1023 is "spurious" (no interrupt)
-	 *
-	 * For now, we ignore all local interrupts so only return an interrupt if it's
-	 * between 30 and 1020.  The test_for_ipi routine below will pick up on IPIs.
-	 *
-	 * A simple read from the controller will tell us the number of the highest
-	 * priority enabled interrupt.  We then just need to check whether it is in the
-	 * valid range for an IRQ (30-1020 inclusive).
-	 */
-
-	.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
-	ldr     \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */
-	ldr	\tmp, =1021
-	bic     \irqnr, \irqstat, #0x1c00
-	cmp     \irqnr, #29
-	cmpcc	\irqnr, \irqnr
-	cmpne	\irqnr, \tmp
-	cmpcs	\irqnr, \irqnr
-	.endm
-
-	/* We assume that irqstat (the raw value of the IRQ acknowledge
-	 * register) is preserved from the macro above.
-	 * If there is an IPI, we immediately signal end of interrupt on the
-	 * controller, since this requires the original irqstat value which
-	 * we won't easily be able to recreate later.
-	 */
-
-	.macro test_for_ipi, irqnr, irqstat, base, tmp
-	bic	\irqnr, \irqstat, #0x1c00
-	cmp	\irqnr, #16
-	strcc	\irqstat, [\base, #GIC_CPU_EOI]
-	cmpcs	\irqnr, \irqnr
-	.endm
-
-	/* As above, this assumes that irqstat and base are preserved.. */
-
-	.macro test_for_ltirq, irqnr, irqstat, base, tmp
-	bic	\irqnr, \irqstat, #0x1c00
-	mov 	\tmp, #0
-	cmp	\irqnr, #29
-	moveq	\tmp, #1
-	streq	\irqstat, [\base, #GIC_CPU_EOI]
-	cmp	\tmp, #0
-	.endm
-
#8 lore raw

PATCH 7/7 ARM: Use shared GIC entry macros on OMAP

In reply to Magnus Damm

From: Magnus Damm <[email protected]>

Common GIC entry macro for omap

---

 arch/arm/mach-omap2/include/mach/entry-macro.S |   92 ++++++++----------------
 1 file changed, 31 insertions(+), 61 deletions(-)
arch/arm/mach-omap2/include/mach/entry-macro.S +31 -61
@@ -105,6 +105,35 @@ omap_irq_base:	.word	0
 9999:
 		.endm
 
+#ifdef CONFIG_SMP
+		/* We assume that irqstat (the raw value of the IRQ acknowledge
+		 * register) is preserved from the macro above.
+		 * If there is an IPI, we immediately signal end of interrupt
+		 * on the controller, since this requires the original irqstat
+		 * value which we won't easily be able to recreate later.
+		 */
+
+		.macro test_for_ipi, irqnr, irqstat, base, tmp
+		bic	\irqnr, \irqstat, #0x1c00
+		cmp	\irqnr, #16
+		it	cc
+		strcc	\irqstat, [\base, #GIC_CPU_EOI]
+		it	cs
+		cmpcs	\irqnr, \irqnr
+		.endm
+
+		/* As above, this assumes that irqstat and base are preserved */
+
+		.macro test_for_ltirq, irqnr, irqstat, base, tmp
+		bic	\irqnr, \irqstat, #0x1c00
+		mov 	\tmp, #0
+		cmp	\irqnr, #29
+		itt	eq
+		moveq	\tmp, #1
+		streq	\irqstat, [\base, #GIC_CPU_EOI]
+		cmp	\tmp, #0
+		.endm
+#endif	/* CONFIG_SMP */
 
 #else	/* MULTI_OMAP2 */
 
@@ -141,74 +170,15 @@ omap_irq_base:	.word	0
 
 
 #ifdef CONFIG_ARCH_OMAP4
+#include <asm/hardware/entry-macro-gic.S>
 
 		.macro  get_irqnr_preamble, base, tmp
 		ldr     \base, =OMAP4_IRQ_BASE
 		.endm
 
-		/*
-		 * The interrupt numbering scheme is defined in the
-		 * interrupt controller spec.  To wit:
-		 *
-		 * Interrupts 0-15 are IPI
-		 * 16-28 are reserved
-		 * 29-31 are local.  We allow 30 to be used for the watchdog.
-		 * 32-1020 are global
-		 * 1021-1022 are reserved
-		 * 1023 is "spurious" (no interrupt)
-		 *
-		 * For now, we ignore all local interrupts so only return an
-		 * interrupt if it's between 30 and 1020.  The test_for_ipi
-		 * routine below will pick up on IPIs.
-		 * A simple read from the controller will tell us the number
-		 * of the highest priority enabled interrupt.
-		 * We then just need to check whether it is in the
-		 * valid range for an IRQ (30-1020 inclusive).
-		 */
-		.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-		ldr     \irqstat, [\base, #GIC_CPU_INTACK]
-
-		ldr     \tmp, =1021
-
-		bic     \irqnr, \irqstat, #0x1c00
-
-		cmp     \irqnr, #29
-		cmpcc   \irqnr, \irqnr
-		cmpne   \irqnr, \tmp
-		cmpcs   \irqnr, \irqnr
-		.endm
 #endif
-#endif	/* MULTI_OMAP2 */
-
-#ifdef CONFIG_SMP
-		/* We assume that irqstat (the raw value of the IRQ acknowledge
-		 * register) is preserved from the macro above.
-		 * If there is an IPI, we immediately signal end of interrupt
-		 * on the controller, since this requires the original irqstat
-		 * value which we won't easily be able to recreate later.
-		 */
-
-		.macro test_for_ipi, irqnr, irqstat, base, tmp
-		bic	\irqnr, \irqstat, #0x1c00
-		cmp	\irqnr, #16
-		it	cc
-		strcc	\irqstat, [\base, #GIC_CPU_EOI]
-		it	cs
-		cmpcs	\irqnr, \irqnr
-		.endm
-
-		/* As above, this assumes that irqstat and base are preserved */
 
-		.macro test_for_ltirq, irqnr, irqstat, base, tmp
-		bic	\irqnr, \irqstat, #0x1c00
-		mov 	\tmp, #0
-		cmp	\irqnr, #29
-		itt	eq
-		moveq	\tmp, #1
-		streq	\irqstat, [\base, #GIC_CPU_EOI]
-		cmp	\tmp, #0
-		.endm
-#endif	/* CONFIG_SMP */
+#endif	/* MULTI_OMAP2 */
 
 		.macro	irq_prio_table
 		.endm
Acked-by on v1 7/7
#9 lore raw

RE: [PATCH 07/07] ARM: Use shared GIC entry macros on OMAP

Quoted 11 lines

-----Original Message-----
From: Magnus Damm [mailto:magnus.damm at gmail.com]
Sent: Friday, November 12, 2010 1:52 PM
To: linux at arm.linux.org.uk
Cc: kgene.kim at samsung.com; kmpark at infradead.org; konkers at android.com; tony at atomide.com; adharmap at codeaurora.org; avorontsov at mvista.com; linux- kernel at vger.kernel.org; srinidhikasagar at gmail.com; dwalker at codeaurora.org; Shilimkar, Santosh; ccross at android.com; olof at lixom.net; Magnus Damm; linux-arm-kernel at lists.infradead.org
Subject: [PATCH 07/07] ARM: Use shared GIC entry macros on OMAP

Quoted 6 lines

From: Magnus Damm <[email protected]>

Common GIC entry macro for omap

Quoted 126 lines

---

 arch/arm/mach-omap2/include/mach/entry-macro.S |   92 ++++++++-----------
-----
 1 file changed, 31 insertions(+), 61 deletions(-)
arch/arm/mach-omap2/include/mach/entry-macro.S +0 -0

16:10:51.000000000 +0900

arch/arm/mach-omap2/include/mach/entry-macro.S +2 -0
@@ -105,6 +105,35 @@ omap_irq_base:	.word	0
 9999:
 		.endm
 
+#ifdef CONFIG_SMP
+		/* We assume that irqstat (the raw value of the IRQ

acknowledge

arch/arm/mach-omap2/include/mach/entry-macro.S +16 -0
+		 * register) is preserved from the macro above.
+		 * If there is an IPI, we immediately signal end of interrupt
+		 * on the controller, since this requires the original irqstat
+		 * value which we won't easily be able to recreate later.
+		 */
+
+		.macro test_for_ipi, irqnr, irqstat, base, tmp
+		bic	\irqnr, \irqstat, #0x1c00
+		cmp	\irqnr, #16
+		it	cc
+		strcc	\irqstat, [\base, #GIC_CPU_EOI]
+		it	cs
+		cmpcs	\irqnr, \irqnr
+		.endm
+
+		/* As above, this assumes that irqstat and base are preserved

*/

arch/arm/mach-omap2/include/mach/entry-macro.S +12 -35
+
+		.macro test_for_ltirq, irqnr, irqstat, base, tmp
+		bic	\irqnr, \irqstat, #0x1c00
+		mov 	\tmp, #0
+		cmp	\irqnr, #29
+		itt	eq
+		moveq	\tmp, #1
+		streq	\irqstat, [\base, #GIC_CPU_EOI]
+		cmp	\tmp, #0
+		.endm
+#endif	/* CONFIG_SMP */
 
 #else	/* MULTI_OMAP2 */
@@ -141,74 +170,15 @@ omap_irq_base:	.word	0
 
 
 #ifdef CONFIG_ARCH_OMAP4
+#include <asm/hardware/entry-macro-gic.S>
 
 		.macro  get_irqnr_preamble, base, tmp
 		ldr     \base, =OMAP4_IRQ_BASE
 		.endm
 
-		/*
-		 * The interrupt numbering scheme is defined in the
-		 * interrupt controller spec.  To wit:
-		 *
-		 * Interrupts 0-15 are IPI
-		 * 16-28 are reserved
-		 * 29-31 are local.  We allow 30 to be used for the watchdog.
-		 * 32-1020 are global
-		 * 1021-1022 are reserved
-		 * 1023 is "spurious" (no interrupt)
-		 *
-		 * For now, we ignore all local interrupts so only return an
-		 * interrupt if it's between 30 and 1020.  The test_for_ipi
-		 * routine below will pick up on IPIs.
-		 * A simple read from the controller will tell us the number
-		 * of the highest priority enabled interrupt.
-		 * We then just need to check whether it is in the
-		 * valid range for an IRQ (30-1020 inclusive).
-		 */
-		.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-		ldr     \irqstat, [\base, #GIC_CPU_INTACK]
-
-		ldr     \tmp, =1021
-
-		bic     \irqnr, \irqstat, #0x1c00
-
-		cmp     \irqnr, #29
-		cmpcc   \irqnr, \irqnr
-		cmpne   \irqnr, \tmp
-		cmpcs   \irqnr, \irqnr
-		.endm
 #endif
-#endif	/* MULTI_OMAP2 */
-
-#ifdef CONFIG_SMP
-		/* We assume that irqstat (the raw value of the IRQ

acknowledge

arch/arm/mach-omap2/include/mach/entry-macro.S +0 -16
-		 * register) is preserved from the macro above.
-		 * If there is an IPI, we immediately signal end of interrupt
-		 * on the controller, since this requires the original irqstat
-		 * value which we won't easily be able to recreate later.
-		 */
-
-		.macro test_for_ipi, irqnr, irqstat, base, tmp
-		bic	\irqnr, \irqstat, #0x1c00
-		cmp	\irqnr, #16
-		it	cc
-		strcc	\irqstat, [\base, #GIC_CPU_EOI]
-		it	cs
-		cmpcs	\irqnr, \irqnr
-		.endm
-
-		/* As above, this assumes that irqstat and base are preserved

*/

arch/arm/mach-omap2/include/mach/entry-macro.S +1 -10
-		.macro test_for_ltirq, irqnr, irqstat, base, tmp
-		bic	\irqnr, \irqstat, #0x1c00
-		mov 	\tmp, #0
-		cmp	\irqnr, #29
-		itt	eq
-		moveq	\tmp, #1
-		streq	\irqstat, [\base, #GIC_CPU_EOI]
-		cmp	\tmp, #0
-		.endm
-#endif	/* CONFIG_SMP */
+#endif	/* MULTI_OMAP2 */
 
 		.macro	irq_prio_table
 		.endm
maintainer
#10 lore raw

Re: [PATCH 07/07] ARM: Use shared GIC entry macros on OMAP

Quoted 11 lines · Shilimkar, Santosh
Quoted 11 lines

-----Original Message-----
From: Magnus Damm [mailto:magnus.damm at gmail.com]
Sent: Friday, November 12, 2010 1:52 PM
To: linux at arm.linux.org.uk
Cc: kgene.kim at samsung.com; kmpark at infradead.org; konkers at android.com; tony at atomide.com; adharmap at codeaurora.org; avorontsov at mvista.com; linux- kernel at vger.kernel.org; srinidhikasagar at gmail.com; dwalker at codeaurora.org; Shilimkar, Santosh; ccross at android.com; olof at lixom.net; Magnus Damm; linux-arm-kernel at lists.infradead.org
Subject: [PATCH 07/07] ARM: Use shared GIC entry macros on OMAP

Quoted 7 lines
Quoted 6 lines

From: Magnus Damm <[email protected]>

Common GIC entry macro for omap

Looks like the From: field got trashed on this one assuming you're using the patch I posted earlier :)

Tony

#11 lore raw
In reply to Magnus Damm
Quoted 10 lines · Magnus Damm

ARM: Common GIC entry macro code V3

[PATCH 01/07] ARM: Introduce asm/hardware/entry-macro-gic.S [PATCH 02/07] ARM: Use shared GIC entry macros on CNS3XXX [PATCH 03/07] ARM: Use shared GIC entry macros on Realview [PATCH 04/07] ARM: Use shared GIC entry macros on Tegra [PATCH 05/07] ARM: Use shared GIC entry macros on UX500 [PATCH 06/07] ARM: Use shared GIC entry macros on Vexpress [PATCH 07/07] ARM: Use shared GIC entry macros on OMAP

Quoted 2 lines

Put GIC demux code in a common place to avoid duplicated code.

Looks like a very nice cleanup!

Arnd