Skip to contentSkip to conversation

bnx2: Fix reset bug on 5709

PATCH Applied Michael Chan 2 participants 4 messages Nov 25, 2010 – Nov 28, 2010

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 bnx2: Fix reset bug on 5709

From: Eddie Wai <[email protected]>

The 5709 chip requires the BNX2_MISC_NEW_CORE_CTL_DMA_ENABLE bit to be cleared and polling for pending DMAs to complete before chip reset. Without this step, we've seen NMIs during repeated resets of the chip.

---
 drivers/net/bnx2.c |   29 ++++++++++++++++++++++-------
 drivers/net/bnx2.h |    2 ++
 2 files changed, 24 insertions(+), 7 deletions(-)
drivers/net/bnx2.c +22 -7
index 062600b..83af01d 100644
@@ -4645,13 +4645,28 @@ bnx2_reset_chip(struct bnx2 *bp, u32 reset_code)
 
 	/* Wait for the current PCI transaction to complete before
 	 * issuing a reset. */
-	REG_WR(bp, BNX2_MISC_ENABLE_CLR_BITS,
-	       BNX2_MISC_ENABLE_CLR_BITS_TX_DMA_ENABLE |
-	       BNX2_MISC_ENABLE_CLR_BITS_DMA_ENGINE_ENABLE |
-	       BNX2_MISC_ENABLE_CLR_BITS_RX_DMA_ENABLE |
-	       BNX2_MISC_ENABLE_CLR_BITS_HOST_COALESCE_ENABLE);
-	val = REG_RD(bp, BNX2_MISC_ENABLE_CLR_BITS);
-	udelay(5);
+	if ((CHIP_NUM(bp) == CHIP_NUM_5706) ||
+	    (CHIP_NUM(bp) == CHIP_NUM_5708)) {
+		REG_WR(bp, BNX2_MISC_ENABLE_CLR_BITS,
+		       BNX2_MISC_ENABLE_CLR_BITS_TX_DMA_ENABLE |
+		       BNX2_MISC_ENABLE_CLR_BITS_DMA_ENGINE_ENABLE |
+		       BNX2_MISC_ENABLE_CLR_BITS_RX_DMA_ENABLE |
+		       BNX2_MISC_ENABLE_CLR_BITS_HOST_COALESCE_ENABLE);
+		val = REG_RD(bp, BNX2_MISC_ENABLE_CLR_BITS);
+		udelay(5);
+	} else {  /* 5709 */
+		val = REG_RD(bp, BNX2_MISC_NEW_CORE_CTL);
+		val &= ~BNX2_MISC_NEW_CORE_CTL_DMA_ENABLE;
+		REG_WR(bp, BNX2_MISC_NEW_CORE_CTL, val);
+		val = REG_RD(bp, BNX2_MISC_NEW_CORE_CTL);
+
+		for (i = 0; i < 100; i++) {
+			msleep(1);
+			val = REG_RD(bp, BNX2_PCICFG_DEVICE_CONTROL);
+			if (!(val & BNX2_PCICFG_DEVICE_STATUS_NO_PEND))
+				break;
+		}
+	}
 
 	/* Wait for the firmware to tell us it is ok to issue a reset. */
 	bnx2_fw_sync(bp, BNX2_DRV_MSG_DATA_WAIT0 | reset_code, 1, 1);
drivers/net/bnx2.h +2 -0
index bf4c342..5488a2e 100644
@@ -461,6 +461,8 @@ struct l2_fhdr {
 #define BNX2_PCICFG_MAILBOX_QUEUE_ADDR			0x00000090
 #define BNX2_PCICFG_MAILBOX_QUEUE_DATA			0x00000094
 
+#define BNX2_PCICFG_DEVICE_CONTROL			0x000000b4
+#define BNX2_PCICFG_DEVICE_STATUS_NO_PEND		 ((1L<<5)<<16)
 
 /*
  *  pci_reg definition
Signature · 1 line
1.6.4.GIT
#1 lore raw

PATCH 2/2 bnx2: Remove config access to non-standard registers

In KVM passthrough mode, the driver may not have config access to non-standard registers. The BNX2_PCICFG_MISC_CONFIG config register access to setup mailbox swapping can be done using MMIO.

Update version to 2.0.20.

---
 drivers/net/bnx2.c |   16 ++++++++--------
 1 files changed, 8 insertions(+), 8 deletions(-)
drivers/net/bnx2.c +8 -8
index 83af01d..4c0106f 100644
@@ -56,8 +56,8 @@
 #include "bnx2_fw.h"
 
 #define DRV_MODULE_NAME		"bnx2"
-#define DRV_MODULE_VERSION	"2.0.18"
-#define DRV_MODULE_RELDATE	"Oct 7, 2010"
+#define DRV_MODULE_VERSION	"2.0.20"
+#define DRV_MODULE_RELDATE	"Nov 24, 2010"
 #define FW_MIPS_FILE_06		"bnx2/bnx2-mips-06-6.0.15.fw"
 #define FW_RV2P_FILE_06		"bnx2/bnx2-rv2p-06-6.0.15.fw"
 #define FW_MIPS_FILE_09		"bnx2/bnx2-mips-09-6.0.17.fw"
@@ -4688,7 +4688,7 @@ bnx2_reset_chip(struct bnx2 *bp, u32 reset_code)
 		val = BNX2_PCICFG_MISC_CONFIG_REG_WINDOW_ENA |
 		      BNX2_PCICFG_MISC_CONFIG_TARGET_MB_WORD_SWAP;
 
-		pci_write_config_dword(bp->pdev, BNX2_PCICFG_MISC_CONFIG, val);
+		REG_WR(bp, BNX2_PCICFG_MISC_CONFIG, val);
 
 	} else {
 		val = BNX2_PCICFG_MISC_CONFIG_CORE_RST_REQ |
@@ -7929,15 +7929,15 @@ bnx2_init_board(struct pci_dev *pdev, struct net_device *dev)
 		goto err_out_release;
 	}
 
+	bnx2_set_power_state(bp, PCI_D0);
+
 	/* Configure byte swap and enable write to the reg_window registers.
 	 * Rely on CPU to do target byte swapping on big endian systems
 	 * The chip's target access swapping will not swap all accesses
 	 */
-	pci_write_config_dword(bp->pdev, BNX2_PCICFG_MISC_CONFIG,
-			       BNX2_PCICFG_MISC_CONFIG_REG_WINDOW_ENA |
-			       BNX2_PCICFG_MISC_CONFIG_TARGET_MB_WORD_SWAP);
-
-	bnx2_set_power_state(bp, PCI_D0);
+	REG_WR(bp, BNX2_PCICFG_MISC_CONFIG,
+		   BNX2_PCICFG_MISC_CONFIG_REG_WINDOW_ENA |
+		   BNX2_PCICFG_MISC_CONFIG_TARGET_MB_WORD_SWAP);
 
 	bp->chip_id = REG_RD(bp, BNX2_MISC_ID);
 
Signature · 1 line
1.6.4.GIT
maintainer Applied
#2 lore raw

Re: [PATCH net-next 2/2] bnx2: Remove config access to non-standard registers

From: "Michael Chan" <[email protected]>
Date: Wed, 24 Nov 2010 15:48:55 -0800

Quoted 7 lines

In KVM passthrough mode, the driver may not have config access to non-standard registers. The BNX2_PCICFG_MISC_CONFIG config register access to setup mailbox swapping can be done using MMIO.

Update version to 2.0.20.

Applied.

maintainer Applied
#3 lore raw
In reply to Michael Chan

From: "Michael Chan" <[email protected]>
Date: Wed, 24 Nov 2010 15:48:54 -0800

Quoted 8 lines

From: Eddie Wai <[email protected]>

The 5709 chip requires the BNX2_MISC_NEW_CORE_CTL_DMA_ENABLE bit to be cleared and polling for pending DMAs to complete before chip reset. Without this step, we've seen NMIs during repeated resets of the chip.

Applied.