Skip to contentSkip to conversation

Kirkwood: Add support for 6282 based QNAP devices

PATCH New Martin Michlmayr 4 participants 8 messages Nov 29, 2010 – Dec 7, 2010

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Kirkwood: Add support for 6282 based QNAP devices

Add support for the QNAP NAS devices based on Marvell's 6282 Kirkwood chip (TS-119P+, TS-219P+ and TS-419P+). The differences to the 6281 based devices are:
- Ethernet PHY address
- GPIOs used for buttons (TS-119P+/TS-219P+)

arch/arm/mach-kirkwood/Kconfig +4 -4
@@ -48,15 +48,15 @@ config MACH_TS219
 	bool "QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P Turbo NAS"
 	help
 	  Say 'Y' here if you want your kernel to support the
-	  QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P Turbo NAS
-	  devices.
+	  QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and
+	  TS-219P+ Turbo NAS devices.
 
 config MACH_TS41X
 	bool "QNAP TS-410, TS-410U, TS-419P and TS-419U Turbo NAS"
 	help
 	  Say 'Y' here if you want your kernel to support the
-	  QNAP TS-410, TS-410U, TS-419P and TS-419U Turbo NAS
-	  devices.
+	  QNAP TS-410, TS-410U, TS-419P, TS-419P+ and TS-419U Turbo
+	  NAS devices.
 
 config MACH_DOCKSTAR
 	bool "Seagate FreeAgent DockStar"
arch/arm/mach-kirkwood/ts219-setup.c +14 -2
index 6710bd7..dc999c4 100644
@@ -80,15 +80,19 @@ static unsigned int qnap_ts219_mpp_config[] __initdata = {
 	MPP11_UART0_RXD,
 	MPP13_UART1_TXD,	/* PIC controller */
 	MPP14_UART1_RXD,	/* PIC controller */
-	MPP15_GPIO,		/* USB Copy button */
-	MPP16_GPIO,		/* Reset button */
+	MPP15_GPIO,		/* USB Copy button (on devices with 88F6281) */
+	MPP16_GPIO,		/* Reset button (on devices with 88F6281) */
 	MPP36_GPIO,		/* RAM: 0: 256 MB, 1: 512 MB */
+	MPP37_GPIO,		/* Reset button (on devices with 88F6282) */
+	MPP43_GPIO,		/* USB Copy button (on devices with 88F6282) */
 	MPP44_GPIO,		/* Board ID: 0: TS-11x, 1: TS-21x */
 	0
 };
 
 static void __init qnap_ts219_init(void)
 {
+	u32 dev, rev;
+
 	/*
 	 * Basic setup. Needs to be called early.
 	 */
@@ -100,6 +104,14 @@ static void __init qnap_ts219_init(void)
 	qnap_tsx1x_register_flash();
 	kirkwood_i2c_init();
 	i2c_register_board_info(0, &qnap_ts219_i2c_rtc, 1);
+
+	kirkwood_pcie_id(&dev, &rev);
+	if (dev == MV88F6282_DEV_ID) {
+		qnap_ts219_buttons[0].gpio = 43; /* USB Copy button */
+		qnap_ts219_buttons[1].gpio = 37; /* Reset button */
+		qnap_ts219_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
+	}
+
 	kirkwood_ge00_init(&qnap_ts219_ge00_data);
 	kirkwood_sata_init(&qnap_ts219_sata_data);
 	kirkwood_ehci_init();
arch/arm/mach-kirkwood/ts41x-setup.c +9 -0
index 3587a28..9a44029 100644
@@ -119,6 +119,8 @@ static unsigned int qnap_ts41x_mpp_config[] __initdata = {
 
 static void __init qnap_ts41x_init(void)
 {
+	u32 dev, rev;
+
 	/*
 	 * Basic setup. Needs to be called early.
 	 */
@@ -130,8 +132,15 @@ static void __init qnap_ts41x_init(void)
 	qnap_tsx1x_register_flash();
 	kirkwood_i2c_init();
 	i2c_register_board_info(0, &qnap_ts41x_i2c_rtc, 1);
+
+	kirkwood_pcie_id(&dev, &rev);
+	if (dev == MV88F6282_DEV_ID) {
+		qnap_ts41x_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
+		qnap_ts41x_ge01_data.phy_addr = MV643XX_ETH_PHY_ADDR(1);
+	}
 	kirkwood_ge00_init(&qnap_ts41x_ge00_data);
 	kirkwood_ge01_init(&qnap_ts41x_ge01_data);
+
 	kirkwood_sata_init(&qnap_ts41x_sata_data);
 	kirkwood_ehci_init();
 	platform_device_register(&qnap_ts41x_button_device);
Signature · 2 lines
Martin Michlmayr
http://www.cyrius.com/
#1 lore raw

PATCH 1/1 Kirkwood: Add support for 6282 based QNAP devices

Quoted 11 lines · Martin Michlmayr

Add support for the QNAP NAS devices based on Marvell's 6282 Kirkwood chip (TS-119P+, TS-219P+ and TS-419P+). ?The differences to the 6281 based devices are:
?- Ethernet PHY address
?- GPIOs used for buttons (TS-119P+/TS-219P+)

arch/arm/mach-kirkwood/Kconfig +0 -0
@@ -48,15 +48,15 @@ config MACH_TS219
Quoted 1 line

? ? ? ?bool "QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P Turbo NAS"

please add the new devices to the title as well.

Quoted 98 lines

? ? ? ?help
? ? ? ? ?Say 'Y' here if you want your kernel to support the
- ? ? ? ? QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P Turbo NAS
- ? ? ? ? devices.
+ ? ? ? ? QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and
+ ? ? ? ? TS-219P+ Turbo NAS devices.

?config MACH_TS41X
? ? ? ?bool "QNAP TS-410, TS-410U, TS-419P and TS-419U Turbo NAS" ? ? ? ?help
? ? ? ? ?Say 'Y' here if you want your kernel to support the
- ? ? ? ? QNAP TS-410, TS-410U, TS-419P and TS-419U Turbo NAS
- ? ? ? ? devices.
+ ? ? ? ? QNAP TS-410, TS-410U, TS-419P, TS-419P+ and TS-419U Turbo
+ ? ? ? ? NAS devices.

?config MACH_DOCKSTAR
? ? ? ?bool "Seagate FreeAgent DockStar"

arch/arm/mach-kirkwood/ts219-setup.c +0 -0
index 6710bd7..dc999c4 100644
@@ -80,15 +80,19 @@ static unsigned int qnap_ts219_mpp_config[] __initdata = {
 ? ? ? ?MPP11_UART0_RXD,

? ? ? ?MPP13_UART1_TXD, ? ? ? ?/* PIC controller */
? ? ? ?MPP14_UART1_RXD, ? ? ? ?/* PIC controller */
- ? ? ? MPP15_GPIO, ? ? ? ? ? ? /* USB Copy button */
- ? ? ? MPP16_GPIO, ? ? ? ? ? ? /* Reset button */
+ ? ? ? MPP15_GPIO, ? ? ? ? ? ? /* USB Copy button (on devices with 88F6281) */
+ ? ? ? MPP16_GPIO, ? ? ? ? ? ? /* Reset button (on devices with 88F6281) */ ? ? ? ?MPP36_GPIO, ? ? ? ? ? ? /* RAM: 0: 256 MB, 1: 512 MB */
+ ? ? ? MPP37_GPIO, ? ? ? ? ? ? /* Reset button (on devices with 88F6282) */
+ ? ? ? MPP43_GPIO, ? ? ? ? ? ? /* USB Copy button (on devices with 88F6282) */ ? ? ? ?MPP44_GPIO, ? ? ? ? ? ? /* Board ID: 0: TS-11x, 1: TS-21x */ ? ? ? ?0
?};

?static void __init qnap_ts219_init(void)
?{
+ ? ? ? u32 dev, rev;
+
? ? ? ?/*
? ? ? ? * Basic setup. Needs to be called early.
? ? ? ? */

arch/arm/mach-kirkwood/ts219-setup.c +8 -0
@@ -100,6 +104,14 @@ static void __init qnap_ts219_init(void)
 ? ? ? ?qnap_tsx1x_register_flash();
 ? ? ? ?kirkwood_i2c_init();
 ? ? ? ?i2c_register_board_info(0, &qnap_ts219_i2c_rtc, 1);
+
+ ? ? ? kirkwood_pcie_id(&dev, &rev);
+ ? ? ? if (dev == MV88F6282_DEV_ID) {
+ ? ? ? ? ? ? ? qnap_ts219_buttons[0].gpio = 43; /* USB Copy button */
+ ? ? ? ? ? ? ? qnap_ts219_buttons[1].gpio = 37; /* Reset button */
+ ? ? ? ? ? ? ? qnap_ts219_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
+ ? ? ? }
+
 ? ? ? ?kirkwood_ge00_init(&qnap_ts219_ge00_data);
 ? ? ? ?kirkwood_sata_init(&qnap_ts219_sata_data);
 ? ? ? ?kirkwood_ehci_init();
arch/arm/mach-kirkwood/ts41x-setup.c +2 -0
index 3587a28..9a44029 100644
@@ -119,6 +119,8 @@ static unsigned int qnap_ts41x_mpp_config[] __initdata = {
 
 ?static void __init qnap_ts41x_init(void)
 ?{
+ ? ? ? u32 dev, rev;
+

? ? ? ?/*
? ? ? ? * Basic setup. Needs to be called early.
? ? ? ? */

arch/arm/mach-kirkwood/ts41x-setup.c +7 -1
@@ -130,8 +132,15 @@ static void __init qnap_ts41x_init(void)
 ? ? ? ?qnap_tsx1x_register_flash();
 ? ? ? ?kirkwood_i2c_init();
 ? ? ? ?i2c_register_board_info(0, &qnap_ts41x_i2c_rtc, 1);
+
+ ? ? ? kirkwood_pcie_id(&dev, &rev);
+ ? ? ? if (dev == MV88F6282_DEV_ID) {
+ ? ? ? ? ? ? ? qnap_ts41x_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
+ ? ? ? ? ? ? ? qnap_ts41x_ge01_data.phy_addr = MV643XX_ETH_PHY_ADDR(1);
+ ? ? ? }
 ? ? ? ?kirkwood_ge00_init(&qnap_ts41x_ge00_data);
 ? ? ? ?kirkwood_ge01_init(&qnap_ts41x_ge01_data);
+
 ? ? ? ?kirkwood_sata_init(&qnap_ts41x_sata_data);
 ? ? ? ?kirkwood_ehci_init();
 ? ? ? ?platform_device_register(&qnap_ts41x_button_device);
 
--

Martin Michlmayr
http://www.cyrius.com/

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#2 lore raw

PATCH 1/1 Kirkwood: Add support for 6282 based QNAP devices

Quoted 2 lines · saeed bishara
Quoted 1 line

? ? ? ?bool "QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P Turbo NAS"

please add the new devices to the title as well.

Ok, here's a new version:

From: Martin Michlmayr <[email protected]>

Add support for the QNAP NAS devices based on Marvell's 6282 Kirkwood chip (TS-119P+, TS-219P+ and TS-419P+). The differences to the 6281 based devices are:
- Ethernet PHY address
- GPIOs used for buttons (TS-119P+/TS-219P+)

arch/arm/mach-kirkwood/Kconfig +6 -6
index 3410633..7fc603b 100644
@@ -45,18 +45,18 @@ config MACH_GURUPLUG
 	  Marvell GuruPlug Reference Board.
 
 config MACH_TS219
-	bool "QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P Turbo NAS"
+	bool "QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and TS-219P+ Turbo NAS"
 	help
 	  Say 'Y' here if you want your kernel to support the
-	  QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P Turbo NAS
-	  devices.
+	  QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and
+	  TS-219P+ Turbo NAS devices.
 
 config MACH_TS41X
-	bool "QNAP TS-410, TS-410U, TS-419P and TS-419U Turbo NAS"
+	bool "QNAP TS-410, TS-410U, TS-419P, TS-419P+ and TS-419U Turbo NAS"
 	help
 	  Say 'Y' here if you want your kernel to support the
-	  QNAP TS-410, TS-410U, TS-419P and TS-419U Turbo NAS
-	  devices.
+	  QNAP TS-410, TS-410U, TS-419P, TS-419P+ and TS-419U Turbo
+	  NAS devices.
 
 config MACH_DOCKSTAR
 	bool "Seagate FreeAgent DockStar"
arch/arm/mach-kirkwood/ts219-setup.c +14 -2
index 6710bd7..dc999c4 100644
@@ -80,15 +80,19 @@ static unsigned int qnap_ts219_mpp_config[] __initdata = {
 	MPP11_UART0_RXD,
 	MPP13_UART1_TXD,	/* PIC controller */
 	MPP14_UART1_RXD,	/* PIC controller */
-	MPP15_GPIO,		/* USB Copy button */
-	MPP16_GPIO,		/* Reset button */
+	MPP15_GPIO,		/* USB Copy button (on devices with 88F6281) */
+	MPP16_GPIO,		/* Reset button (on devices with 88F6281) */
 	MPP36_GPIO,		/* RAM: 0: 256 MB, 1: 512 MB */
+	MPP37_GPIO,		/* Reset button (on devices with 88F6282) */
+	MPP43_GPIO,		/* USB Copy button (on devices with 88F6282) */
 	MPP44_GPIO,		/* Board ID: 0: TS-11x, 1: TS-21x */
 	0
 };
 
 static void __init qnap_ts219_init(void)
 {
+	u32 dev, rev;
+
 	/*
 	 * Basic setup. Needs to be called early.
 	 */
@@ -100,6 +104,14 @@ static void __init qnap_ts219_init(void)
 	qnap_tsx1x_register_flash();
 	kirkwood_i2c_init();
 	i2c_register_board_info(0, &qnap_ts219_i2c_rtc, 1);
+
+	kirkwood_pcie_id(&dev, &rev);
+	if (dev == MV88F6282_DEV_ID) {
+		qnap_ts219_buttons[0].gpio = 43; /* USB Copy button */
+		qnap_ts219_buttons[1].gpio = 37; /* Reset button */
+		qnap_ts219_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
+	}
+
 	kirkwood_ge00_init(&qnap_ts219_ge00_data);
 	kirkwood_sata_init(&qnap_ts219_sata_data);
 	kirkwood_ehci_init();
arch/arm/mach-kirkwood/ts41x-setup.c +9 -0
index 3587a28..9a44029 100644
@@ -119,6 +119,8 @@ static unsigned int qnap_ts41x_mpp_config[] __initdata = {
 
 static void __init qnap_ts41x_init(void)
 {
+	u32 dev, rev;
+
 	/*
 	 * Basic setup. Needs to be called early.
 	 */
@@ -130,8 +132,15 @@ static void __init qnap_ts41x_init(void)
 	qnap_tsx1x_register_flash();
 	kirkwood_i2c_init();
 	i2c_register_board_info(0, &qnap_ts41x_i2c_rtc, 1);
+
+	kirkwood_pcie_id(&dev, &rev);
+	if (dev == MV88F6282_DEV_ID) {
+		qnap_ts41x_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
+		qnap_ts41x_ge01_data.phy_addr = MV643XX_ETH_PHY_ADDR(1);
+	}
 	kirkwood_ge00_init(&qnap_ts41x_ge00_data);
 	kirkwood_ge01_init(&qnap_ts41x_ge01_data);
+
 	kirkwood_sata_init(&qnap_ts41x_sata_data);
 	kirkwood_ehci_init();
 	platform_device_register(&qnap_ts41x_button_device);
Signature · 2 lines
Martin Michlmayr
http://www.cyrius.com/
#3 lore raw

PATCH 1/1 Kirkwood: Add support for 6282 based QNAP devices

Quoted 117 lines · Martin Michlmayr
Quoted 2 lines · saeed bishara
Quoted 1 line

? ? ? ?bool "QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P Turbo NAS"

please add the new devices to the title as well.

Ok, here's a new version:

From: Martin Michlmayr <[email protected]>

Add support for the QNAP NAS devices based on Marvell's 6282 Kirkwood chip (TS-119P+, TS-219P+ and TS-419P+). ?The differences to the 6281 based devices are:
?- Ethernet PHY address
?- GPIOs used for buttons (TS-119P+/TS-219P+)

arch/arm/mach-kirkwood/Kconfig +0 -0
index 3410633..7fc603b 100644
@@ -45,18 +45,18 @@ config MACH_GURUPLUG

? ? ? ? ?Marvell GuruPlug Reference Board.

?config MACH_TS219
- ? ? ? bool "QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P Turbo NAS"
+ ? ? ? bool "QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and TS-219P+ Turbo NAS" ? ? ? ?help
? ? ? ? ?Say 'Y' here if you want your kernel to support the
- ? ? ? ? QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P Turbo NAS
- ? ? ? ? devices.
+ ? ? ? ? QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and
+ ? ? ? ? TS-219P+ Turbo NAS devices.

?config MACH_TS41X
- ? ? ? bool "QNAP TS-410, TS-410U, TS-419P and TS-419U Turbo NAS"
+ ? ? ? bool "QNAP TS-410, TS-410U, TS-419P, TS-419P+ and TS-419U Turbo NAS" ? ? ? ?help
? ? ? ? ?Say 'Y' here if you want your kernel to support the
- ? ? ? ? QNAP TS-410, TS-410U, TS-419P and TS-419U Turbo NAS
- ? ? ? ? devices.
+ ? ? ? ? QNAP TS-410, TS-410U, TS-419P, TS-419P+ and TS-419U Turbo
+ ? ? ? ? NAS devices.

?config MACH_DOCKSTAR
? ? ? ?bool "Seagate FreeAgent DockStar"

arch/arm/mach-kirkwood/ts219-setup.c +0 -0
index 6710bd7..dc999c4 100644
@@ -80,15 +80,19 @@ static unsigned int qnap_ts219_mpp_config[] __initdata = {
 ? ? ? ?MPP11_UART0_RXD,

? ? ? ?MPP13_UART1_TXD, ? ? ? ?/* PIC controller */
? ? ? ?MPP14_UART1_RXD, ? ? ? ?/* PIC controller */
- ? ? ? MPP15_GPIO, ? ? ? ? ? ? /* USB Copy button */
- ? ? ? MPP16_GPIO, ? ? ? ? ? ? /* Reset button */
+ ? ? ? MPP15_GPIO, ? ? ? ? ? ? /* USB Copy button (on devices with 88F6281) */
+ ? ? ? MPP16_GPIO, ? ? ? ? ? ? /* Reset button (on devices with 88F6281) */ ? ? ? ?MPP36_GPIO, ? ? ? ? ? ? /* RAM: 0: 256 MB, 1: 512 MB */
+ ? ? ? MPP37_GPIO, ? ? ? ? ? ? /* Reset button (on devices with 88F6282) */
+ ? ? ? MPP43_GPIO, ? ? ? ? ? ? /* USB Copy button (on devices with 88F6282) */ ? ? ? ?MPP44_GPIO, ? ? ? ? ? ? /* Board ID: 0: TS-11x, 1: TS-21x */ ? ? ? ?0
?};

?static void __init qnap_ts219_init(void)
?{
+ ? ? ? u32 dev, rev;
+
? ? ? ?/*
? ? ? ? * Basic setup. Needs to be called early.
? ? ? ? */

arch/arm/mach-kirkwood/ts219-setup.c +8 -0
@@ -100,6 +104,14 @@ static void __init qnap_ts219_init(void)
 ? ? ? ?qnap_tsx1x_register_flash();
 ? ? ? ?kirkwood_i2c_init();
 ? ? ? ?i2c_register_board_info(0, &qnap_ts219_i2c_rtc, 1);
+
+ ? ? ? kirkwood_pcie_id(&dev, &rev);
+ ? ? ? if (dev == MV88F6282_DEV_ID) {
+ ? ? ? ? ? ? ? qnap_ts219_buttons[0].gpio = 43; /* USB Copy button */
+ ? ? ? ? ? ? ? qnap_ts219_buttons[1].gpio = 37; /* Reset button */
+ ? ? ? ? ? ? ? qnap_ts219_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
+ ? ? ? }
+
 ? ? ? ?kirkwood_ge00_init(&qnap_ts219_ge00_data);
 ? ? ? ?kirkwood_sata_init(&qnap_ts219_sata_data);
 ? ? ? ?kirkwood_ehci_init();
arch/arm/mach-kirkwood/ts41x-setup.c +2 -0
index 3587a28..9a44029 100644
@@ -119,6 +119,8 @@ static unsigned int qnap_ts41x_mpp_config[] __initdata = {
 
 ?static void __init qnap_ts41x_init(void)
 ?{
+ ? ? ? u32 dev, rev;
+

? ? ? ?/*
? ? ? ? * Basic setup. Needs to be called early.
? ? ? ? */

arch/arm/mach-kirkwood/ts41x-setup.c +7 -1
@@ -130,8 +132,15 @@ static void __init qnap_ts41x_init(void)
 ? ? ? ?qnap_tsx1x_register_flash();
 ? ? ? ?kirkwood_i2c_init();
 ? ? ? ?i2c_register_board_info(0, &qnap_ts41x_i2c_rtc, 1);
+
+ ? ? ? kirkwood_pcie_id(&dev, &rev);
+ ? ? ? if (dev == MV88F6282_DEV_ID) {
+ ? ? ? ? ? ? ? qnap_ts41x_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
+ ? ? ? ? ? ? ? qnap_ts41x_ge01_data.phy_addr = MV643XX_ETH_PHY_ADDR(1);
+ ? ? ? }
 ? ? ? ?kirkwood_ge00_init(&qnap_ts41x_ge00_data);
 ? ? ? ?kirkwood_ge01_init(&qnap_ts41x_ge01_data);
+
 ? ? ? ?kirkwood_sata_init(&qnap_ts41x_sata_data);
 ? ? ? ?kirkwood_ehci_init();
 ? ? ? ?platform_device_register(&qnap_ts41x_button_device);
 
--
Quoted 3 lines

Martin Michlmayr
http://www.cyrius.com/

looks fine to me, Nico, please merge
saeed

#4 lore raw

PATCH 1/1 Kirkwood: Add support for 6282 based QNAP devices

Quoted 8 lines · saeed bishara
Quoted 5 lines · Martin Michlmayr
Quoted 2 lines · saeed bishara
Quoted 1 line

? ? ? ?bool "QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P Turbo NAS"

please add the new devices to the title as well.

Ok, here's a new version:

looks fine to me, Nico, please merge
saeed

Done.

Nicolas

#5 lore raw

PATCH 1/1 Kirkwood: Add support for 6282 based QNAP devices

In reply to Martin Michlmayr
Quoted 7 lines · Martin Michlmayr

Add support for the QNAP NAS devices based on Marvell's 6282 Kirkwood chip (TS-119P+, TS-219P+ and TS-419P+). The differences to the 6281 based devices are:
- Ethernet PHY address
- GPIOs used for buttons (TS-119P+/TS-219P+)

Slightly off-topic, but AFAIK the 6282 is rated for up to 2.0 GHz clock speed, while QNap writes that these devices run at 1.6 GHz. Do you know if QNap has artificially rate-limited the processors, or if they're actually manufactured to only go up to 1.6 GHz?

/Mikael

#6 lore raw

PATCH 1/1 Kirkwood: Add support for 6282 based QNAP devices

Quoted 4 lines · Mikael Pettersson

Slightly off-topic, but AFAIK the 6282 is rated for up to 2.0 GHz clock speed, while QNap writes that these devices run at 1.6 GHz. Do you know if QNap has artificially rate-limited the processors, or if they're actually manufactured to only go up to 1.6 GHz?

There are different variants of the 6282, operating at 1.6 GHz, 1.8 GHz and 2.0 GHz. See
http://www.marvell.com/products/processors/embedded/armada_300/armada_310.pdf

Signature · 2 lines
Martin Michlmayr
http://www.cyrius.com/
#7 lore raw

PATCH 1/1 Kirkwood: Add support for 6282 based QNAP devices

Quoted 8 lines · Martin Michlmayr
Quoted 4 lines · Mikael Pettersson

Slightly off-topic, but AFAIK the 6282 is rated for up to 2.0 GHz clock speed, while QNap writes that these devices run at 1.6 GHz. Do you know if QNap has artificially rate-limited the processors, or if they're actually manufactured to only go up to 1.6 GHz?

There are different variants of the 6282, operating at 1.6 GHz, 1.8 GHz and 2.0 GHz.

Ok. Thanks.