Skip to contentSkip to conversation

mmci: supply per-instance regulator name

PATCH New Linus Walleij 4 participants 7 messages Dec 2, 2010

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 mmci: supply per-instance regulator name

On the Ux500 we have different regulators to different card slots and eMMCs, and some have no regulator. Move the hardcoded "vmmc" regulator name to platform data and supply it that way for the platforms that use it. Remove the ugly and unneeded #ifdef around the regulator fetch code at the same time.

Regression tested on Ux500, U300 and the ARM RealView PB1176.

---
 arch/arm/mach-u300/mmc.c               |    1 +
 arch/arm/mach-ux500/board-mop500-sdi.c |    3 +++
 drivers/mmc/host/mmci.c                |   25 +++++++++++++++++--------
 include/linux/amba/mmci.h              |    2 ++
 4 files changed, 23 insertions(+), 8 deletions(-)
arch/arm/mach-u300/mmc.c +1 -0
index de1ac9a..82e4843 100644
@@ -102,6 +102,7 @@ int __devinit mmc_init(struct amba_device *adev)
 	 * we have a regulator we can control instead.
 	 */
 	/* Nominally 2.85V on our platform */
+	mmci_card->mmc0_plat_data.vcard = "vmmc";
 	mmci_card->mmc0_plat_data.f_max = 24000000;
 	mmci_card->mmc0_plat_data.status = mmc_status;
 	mmci_card->mmc0_plat_data.gpio_wp = -1;
arch/arm/mach-ux500/board-mop500-sdi.c +3 -0
index be5e8cc..6f8d828 100644
@@ -87,6 +87,7 @@ static u32 mop500_sdi0_vdd_handler(struct device *dev, unsigned int vdd,
 }
 
 static struct mmci_platform_data mop500_sdi0_data = {
+	.vcard		= "V-MMC-SD",
 	.vdd_handler	= mop500_sdi0_vdd_handler,
 	.ocr_mask	= MMC_VDD_29_30,
 	.f_max		= 100000000,
@@ -117,6 +118,7 @@ void mop500_sdi_tc35892_init(void)
  */
 
 static struct mmci_platform_data mop500_sdi2_data = {
+	/* This is always on so needs no vcard regulator */
 	.ocr_mask	= MMC_VDD_165_195,
 	.f_max		= 100000000,
 	.capabilities	= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
@@ -129,6 +131,7 @@ static struct mmci_platform_data mop500_sdi2_data = {
  */
 
 static struct mmci_platform_data mop500_sdi4_data = {
+	.vcard		= "V-eMMC1",
 	.ocr_mask	= MMC_VDD_29_30,
 	.f_max		= 100000000,
 	.capabilities	= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA |
drivers/mmc/host/mmci.c +17 -8
index 3709ab3..23e6ebd 100644
@@ -844,14 +844,22 @@ static int __devinit mmci_probe(struct amba_device *dev, struct amba_id *id)
 		mmc->f_max = min(host->mclk, fmax);
 	dev_dbg(mmc_dev(mmc), "clocking block at %u Hz\n", mmc->f_max);
 
-#ifdef CONFIG_REGULATOR
-	/* If we're using the regulator framework, try to fetch a regulator */
-	host->vcc = regulator_get(&dev->dev, "vmmc");
-	if (IS_ERR(host->vcc))
-		host->vcc = NULL;
-	else {
-		int mask = mmc_regulator_get_ocrmask(host->vcc);
+	/* Use a host regulator for card power if one is supplied */
+	if (plat->vcard) {
+		int mask;
+
+		/*
+		 * If getting the regulators fails, or if the
+		 * regulator framework is disabled (yields a NULL
+		 * regulator) we leave this.
+		 */
+		host->vcc = regulator_get(&dev->dev, plat->vcard);
+		if (IS_ERR(host->vcc))
+			host->vcc = NULL;
+		if (host->vcc == NULL)
+			goto no_regulator;
 
+		mask = mmc_regulator_get_ocrmask(host->vcc);
 		if (mask < 0)
 			dev_err(&dev->dev, "error getting OCR mask (%d)\n",
 				mask);
@@ -863,8 +871,9 @@ static int __devinit mmci_probe(struct amba_device *dev, struct amba_id *id)
 				 "(using regulator instead)\n");
 		}
 	}
-#endif
+
 	/* Fall back to platform data if no regulator is found */
+no_regulator:
 	if (host->vcc == NULL)
 		mmc->ocr_avail = plat->ocr_mask;
 	mmc->caps = plat->capabilities;
include/linux/amba/mmci.h +2 -0
index f4ee9ac..614c2b6 100644
@@ -9,6 +9,7 @@
 /**
  * struct mmci_platform_data - platform configuration for the MMCI
  * (also known as PL180) block.
+ * @vcard: name of regulator for card
  * @f_max: the maximum operational frequency for this host in this
  * platform configuration. When this is specified it takes precedence
  * over the module parameter for the same frequency.
@@ -29,6 +30,7 @@
  * this platform, signify anything MMC_CAP_* from mmc/host.h
  */
 struct mmci_platform_data {
+	char *vcard;
 	unsigned int f_max;
 	unsigned int ocr_mask;
 	u32 (*vdd_handler)(struct device *, unsigned int vdd,
Signature · 1 line
1.7.3.2
#1 lore raw

PATCH 1/1 mmci: supply per-instance regulator name

Quoted 5 lines · Linus Walleij

On the Ux500 we have different regulators to different card slots and eMMCs, and some have no regulator. Move the hardcoded "vmmc" regulator name to platform data and supply it that way for the platforms that use it. Remove the ugly and unneeded #ifdef around the regulator fetch code at the same time.

It seems that the regulator code is making all the same mistakes that historically were made with the clk API code.

Rather than using the struct device, it's trying to use the regulator name to distinguish individual sources of supply. This can only lead to lots of regulator names being passed around from layer to layer, rather than the now proven cleaner method that the clk API always set out to do.

I'd like regulator people to think long and hard about the sanity of passing names all the way from platform code into drivers and back into the regulator code before I consider this patch any further.

#2 lore raw

PATCH 1/1 mmci: supply per-instance regulator name

Quoted 2 lines · Russell King - ARM Linux

It seems that the regulator code is making all the same mistakes that historically were made with the clk API code.

It's not...

Quoted 1 line

Rather than using the struct device, it's trying to use the regulator

...it does exactly this. Passing names is not good practice.

#3 lore raw

PATCH 1/1 mmci: supply per-instance regulator name

In reply to Linus Walleij
Quoted 3 lines · Linus Walleij

On the Ux500 we have different regulators to different card slots and eMMCs, and some have no regulator. Move the hardcoded "vmmc" regulator name to platform data and supply it that way for the

You should never be passing regulator names through platform data, this appears to be broken. You should be using the struct device to distingish between multiple instances and using whatever the actual supply names are for multiple supplies on the same device.

Looking at this without seeing the datasheet I'd expect these would end up as vmmcn for suitable values of n.

Quoted 2 lines

platforms that use it. Remove the ugly and unneeded #ifdef around the regulator fetch code at the same time.

This is a separate change and is OK - it's this way as historically the regulator API returned a non-NULL pointer when built out.

drivers/mmc/host/mmci.c static int __devinit mmci_probe(struct amba_device *dev, struct amba_id *id) · line 849

Quoted 2 lines
drivers/mmc/host/mmci.c +2 -0
+       if (plat->vcard) {
+               int mask;

This will break users of this driver on any other platform - the naming of the driver suggests that it's not specific to your SoC.

#4 lore raw

PATCH 1/1 mmci: supply per-instance regulator name

Quoted 5 lines · Mark Brown
Quoted 3 lines · Linus Walleij

On the Ux500 we have different regulators to different card slots and eMMCs, and some have no regulator. Move the hardcoded "vmmc" regulator name to platform data and supply it that way for the

Quoted 7 lines

You should never be passing regulator names through platform data, this appears to be broken. You should be using the struct device to distingish between multiple instances and using whatever the actual supply names are for multiple supplies on the same device.

Looking at this without seeing the datasheet I'd expect these would end up as vmmcn for suitable values of n.

The way the MMCI code is, it only requests one regulator per AMBA device, and therefore only one regulator per struct device. So I don't think the current code needs changing in any way provided the struct device is used to find the corresponding regulator.

#5 lore raw

PATCH 1/1 mmci: supply per-instance regulator name

Quoted 4 lines · Russell King - ARM Linux

The way the MMCI code is, it only requests one regulator per AMBA device, and therefore only one regulator per struct device. So I don't think the current code needs changing in any way provided the struct device is used to find the corresponding regulator.

Hrm. In that case I'm not sure what the problem Linus' patch fixes is - the driver is already requesting using the struct device, I was assuming that the supplies weren't being requested in a fine grained enough fashion.

#6 lore raw

PATCH 1/1 mmci: supply per-instance regulator name

2010/12/2 Mark Brown <[email protected]>:

Quoted 11 lines · Russell King - ARM Linux
Quoted 5 lines

The way the MMCI code is, it only requests one regulator per AMBA device, and therefore only one regulator per struct device. ?So I don't think the current code needs changing in any way provided the struct device is used to find the corresponding regulator.

Hrm. ?In that case I'm not sure what the problem Linus' patch fixes is - the driver is already requesting using the struct device, I was assuming that the supplies weren't being requested in a fine grained enough fashion.

Probably it's the platform board regulator config that needs fixing instead, so as to bind to the correct device.
I'll check...

I'll do another patch that simply gets rid of the #ifdef for now instead.

Thanks,
Linus Walleij