ath5k: Simplify powertable recalculation
PATCH 1/5 ath5k: Simplify powertable recalculation
Let ath5k_hw_txpower() decide if it can re-use the powertable or if it has to be recalculated instead of passing a 'fast' flag from the outside.
--- drivers/net/wireless/ath/ath5k/ath5k.h | 1 + drivers/net/wireless/ath/ath5k/phy.c | 35 ++++++++++++-------------------- 2 files changed, 14 insertions(+), 22 deletions(-)
drivers/net/wireless/ath/ath5k/ath5k.h +1 -0
@@ -1113,6 +1113,7 @@ struct ath5k_hw {s16 txp_cck_ofdm_gainf_delta;/* Value in dB units */ s16 txp_cck_ofdm_pwr_delta; +bool txp_setup; } ah_txpower;struct {
drivers/net/wireless/ath/ath5k/phy.c +13 -22
@@ -3004,6 +3004,8 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah,return -EINVAL ; } + ah->ah_txpower.txp_setup = true; +return 0 ; }
@@ -3105,9 +3107,10 @@ ath5k_setup_rate_powertable(struct ath5k_hw *ah, u16 max_pwr,*/ static int ath5k_hw_txpower (struct ath5k_hw *ah,struct ieee80211_channel *channel, -u8 ee_mode,u8 txpower,bool fast) +u8 ee_mode,u8 txpower) {struct ath5k_rate_pcal_info rate_info; +struct ieee80211_channel *curr_channel = ah->ah_current_channel;u8 type;int ret;
@@ -3138,10 +3141,13 @@ ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel,return -EINVAL ; } -/* If fast is set it means we are on the same channel/mode -* so there is no need to recalculate the powertable, we 'll -* just use the cached one */ -if (!fast) { +/* +* If we don't change channel/mode skip tx powertable calculation +* and use the cached one. +*/ +if (!ah->ah_txpower.txp_setup || + (channel->hw_value != curr_channel->hw_value) || + (channel->center_freq != curr_channel->center_freq)) {/* Reset TX power values */ memset (&ah->ah_txpower,0 ,sizeof (ah->ah_txpower)); ah->ah_txpower.txp_tpc =AR5K_TUNE_TPC_TXPOWER ;
@@ -3159,8 +3165,6 @@ ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel,else ath5k_setup_pcdac_table (ah); - -/* Limit max power if we have a CTL available */ ath5k_get_max_ctl_power (ah, channel);
@@ -3238,7 +3242,7 @@ int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 txpower)ATH5K_DBG (ah->ah_sc,ATH5K_DEBUG_TXPOWER ,"changing txpower to %d\n" , txpower); -return ath5k_hw_txpower (ah, channel, ee_mode, txpower, true); +return ath5k_hw_txpower (ah, channel, ee_mode, txpower); }/*************\
@@ -3251,7 +3255,6 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,struct ieee80211_channel *curr_channel;int ret, i;u32 phy_tst1; -bool fast_txp; ret =0 ;/*
@@ -3282,17 +3285,6 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel, }/* -* If we don't change channel/mode skip -* tx powertable calculation and use the -* cached one. -*/ -if ((channel->hw_value == curr_channel->hw_value) && - (channel->center_freq == curr_channel->center_freq)) - fast_txp = true; -else - fast_txp = false; - -/* * Set TX power * * Note: We need to do that before we set
@@ -3300,8 +3292,7 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,* properly set curve indices. */ ret =ath5k_hw_txpower (ah, channel, ee_mode, - ah->ah_txpower.txp_max_pwr /2 , - fast_txp); + ah->ah_txpower.txp_max_pwr /2 );if (ret)return ret;
PATCH 2/5 ath5k: Separate powertable setup and writing
And rename functions which write the powertable to make it clearer.
--- drivers/net/wireless/ath/ath5k/phy.c | 34 ++++++++++++++++------------------ 1 files changed, 16 insertions(+), 18 deletions(-)
drivers/net/wireless/ath/ath5k/phy.c +16 -18
@@ -2593,7 +2593,7 @@ ath5k_combine_linear_pcdac_curves(struct ath5k_hw *ah, s16* table_min,/* Write PCDAC values on hw */ static void -ath5k_setup_pcdac_table (struct ath5k_hw *ah) +ath5k_write_pcdac_table (struct ath5k_hw *ah) {u8 *pcdac_out = ah->ah_txpower.txp_pd_table;int i;
@@ -2742,7 +2742,7 @@ ath5k_combine_pwr_to_pdadc_curves(struct ath5k_hw *ah,/* Write PDADC values on hw */ static void -ath5k_setup_pwr_to_pdadc_table (struct ath5k_hw *ah,u8 ee_mode) +ath5k_write_pwr_to_pdadc_table (struct ath5k_hw *ah,u8 ee_mode) {struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;u8 *pdadc_out = ah->ah_txpower.txp_pd_table;
@@ -2957,8 +2957,7 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah, (s16 ) pcinfo_R->freq, pcinfo_L->max_pwr, pcinfo_R->max_pwr); -/* We are ready to go, fill PCDAC/PDADC -* table and write settings on hardware */ +/* Fill PCDAC/PDADC table */ switch (type) {case AR5K_PWRTABLE_LINEAR_PCDAC :/* For RF5112 we can have one or two curves
@@ -2971,9 +2970,6 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah,* match max power value with max * table index */ ah->ah_txpower.txp_offset =64 - (table_max[0 ] /2 ); - -/* Write settings on hw */ -ath5k_setup_pcdac_table (ah);break ;case AR5K_PWRTABLE_PWR_TO_PCDAC :/* We are done for RF5111 since it has only
@@ -2983,9 +2979,6 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah,/* No rate powertable adjustment for RF5111 */ ah->ah_txpower.txp_min_idx =0 ; ah->ah_txpower.txp_offset =0 ; - -/* Write settings on hw */ -ath5k_setup_pcdac_table (ah);break ;case AR5K_PWRTABLE_PWR_TO_PDADC :/* Set PDADC boundaries and fill
@@ -2993,9 +2986,6 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah,ath5k_combine_pwr_to_pdadc_curves (ah, table_min, table_max, ee->ee_pd_gains[ee_mode]); -/* Write settings on hw */ -ath5k_setup_pwr_to_pdadc_table (ah, ee_mode); -/* Set txp.offset, note that table_min * can be negative */ ah->ah_txpower.txp_offset = table_min[0 ];
@@ -3009,6 +2999,15 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah,return 0 ; } +/* Write power table for current channel to hw */ +static void +ath5k_write_channel_powertable (struct ath5k_hw *ah,u8 ee_mode,u8 type) +{ +if (type ==AR5K_PWRTABLE_PWR_TO_PDADC ) +ath5k_write_pwr_to_pdadc_table (ah, ee_mode); +else +ath5k_write_pcdac_table (ah); +}/* * Per-rate tx power setting
@@ -3159,11 +3158,10 @@ ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel, ee_mode, type);if (ret)return ret; -/* Write cached table on hw */ - }else if (type ==AR5K_PWRTABLE_PWR_TO_PDADC ) -ath5k_setup_pwr_to_pdadc_table (ah, ee_mode); -else -ath5k_setup_pcdac_table (ah); + } + +/* Write table on hw */ +ath5k_write_channel_powertable (ah, ee_mode, type);/* Limit max power if we have a CTL available */ ath5k_get_max_ctl_power (ah, channel);
Re: [PATCH 2/5] ath5k: Separate powertable setup and writing
2010/12/21 Bruno Randolf <[email protected]>:
Quoted 93 lines
And rename functions which write the powertable to make it clearer.
Signed-off-by Bruno Randolf <[email protected]>---
drivers/net/wireless/ath/ath5k/phy.c | 34 ++++++++++++++++------------------1 files changed, 16 insertions(+), 18 deletions(-)drivers/net/wireless/ath/ath5k/phy.c +0
-0@@ -2593,7 +2593,7 @@ ath5k_combine_linear_pcdac_curves(struct ath5k_hw *ah, s16* table_min, /* Write PCDAC values on hw */static void
drivers/net/wireless/ath/ath5k/phy.c +1
-1-ath5k_setup_pcdac_table(struct ath5k_hw *ah) +ath5k_write_pcdac_table(struct ath5k_hw *ah){
u8 *pcdac_out =ah->ah_txpower.txp_pd_table; int i;drivers/net/wireless/ath/ath5k/phy.c +0
-0@@ -2742,7 +2742,7 @@ ath5k_combine_pwr_to_pdadc_curves(struct ath5k_hw *ah, /* Write PDADC values on hw */static void
drivers/net/wireless/ath/ath5k/phy.c +1
-1-ath5k_setup_pwr_to_pdadc_table(struct ath5k_hw *ah, u8 ee_mode) +ath5k_write_pwr_to_pdadc_table(struct ath5k_hw *ah, u8 ee_mode){
structath5k_eeprom_info*ee =&ah->ah_capabilities.cap_eeprom; u8*pdadc_out=ah->ah_txpower.txp_pd_table;drivers/net/wireless/ath/ath5k/phy.c +1
-2@@ -2957,8 +2957,7 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah, (s16) pcinfo_R->freq, pcinfo_L->max_pwr, pcinfo_R->max_pwr); - /* We are ready to go, fill PCDAC/PDADC - * table and write settings on hardware */ + /* Fill PCDAC/PDADC table */ switch (type) {case
AR5K_PWRTABLE_LINEAR_PCDAC:
/* For RF5112 we can have one or two curvesdrivers/net/wireless/ath/ath5k/phy.c +0
-3@@ -2971,9 +2970,6 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah,* match max power value with max * table index */ ah->ah_txpower.txp_offset = 64 - (table_max[0] / 2); - - /* Write settings on hw */ - ath5k_setup_pcdac_table(ah); break;case
AR5K_PWRTABLE_PWR_TO_PCDAC:
/* We are done for RF5111 since it has onlydrivers/net/wireless/ath/ath5k/phy.c +0
-3@@ -2983,9 +2979,6 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah, /* No rate powertable adjustment for RF5111 */ ah->ah_txpower.txp_min_idx = 0; ah->ah_txpower.txp_offset = 0; - - /* Write settings on hw */ - ath5k_setup_pcdac_table(ah); break;case
AR5K_PWRTABLE_PWR_TO_PDADC:
/* Set PDADC boundaries and filldrivers/net/wireless/ath/ath5k/phy.c +9
-5@@ -2993,9 +2986,6 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah, ath5k_combine_pwr_to_pdadc_curves(ah, table_min, table_max, ee->ee_pd_gains[ee_mode]); - /* Write settings on hw */ - ath5k_setup_pwr_to_pdadc_table(ah, ee_mode); - /* Set txp.offset, note that table_min * can be negative */ ah->ah_txpower.txp_offset = table_min[0];@@ -3009,6 +2999,15 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah, return 0; } +/* Write power table for current channel to hw */ +static void +ath5k_write_channel_powertable (struct ath5k_hw *ah,u8 ee_mode,u8 type) +{ + if (type == AR5K_PWRTABLE_PWR_TO_PDADC) + ath5k_write_pwr_to_pdadc_table(ah, ee_mode); + else + ath5k_write_pcdac_table(ah); +} /** Per-rate tx power setting @@ -3159,11 +3158,10 @@ ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel, ee_mode, type); if (ret) return ret; - /* Write cached table on hw */ - } else if (type == AR5K_PWRTABLE_PWR_TO_PDADC)
drivers/net/wireless/ath/ath5k/phy.c ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel, · line 3167
Quoted 10 lines
drivers/net/wireless/ath/ath5k/phy.c +4
-3- ath5k_setup_pwr_to_pdadc_table(ah, ee_mode); - else - ath5k_setup_pcdac_table(ah); + } + + /* Write table on hw */ + ath5k_write_channel_powertable(ah, ee_mode, type); /* Limit max power if we have a CTL available */ ath5k_get_max_ctl_power(ah, channel);
Signature · 3 lines
GPG ID: 0xD21DB2DB As you read this post global entropy rises. Have Fun ;-) Nick
PATCH 3/5 ath5k: Track current TX power separately from max TX power
In reply to Bruno RandolfAdd a new variable to keep track of the currently configured tx power. Before max_pwr was re-used for keeping the maximum allowed power as well as the current configuration. Doing a min() on it allows you to lower the txpower, but how would you be able to make it higher again?
This patch fixes that by adding a new variable ah_cur_pwr which is used instead of txp_max_pwr to keep the current configuration. txp_max_pwr is used to check if we are within the limits.
Another problem fixed by this patch is that it avoids setting a zero txpower when things are initialized first and the current power is not yet set.
--- drivers/net/wireless/ath/ath5k/ath5k.h | 1 + drivers/net/wireless/ath/ath5k/phy.c | 7 +++---- 2 files changed, 4 insertions(+), 4 deletions(-)
drivers/net/wireless/ath/ath5k/ath5k.h +1 -0
@@ -1107,6 +1107,7 @@ struct ath5k_hw {/* Values in 0.25dB units */ s16 txp_min_pwr;s16 txp_max_pwr; +s16 txp_cur_pwr;/* Values in 0.5dB units */ s16 txp_offset;s16 txp_ofdm;
drivers/net/wireless/ath/ath5k/phy.c +3 -4
@@ -3096,7 +3096,7 @@ ath5k_setup_rate_powertable(struct ath5k_hw *ah, u16 max_pwr,/* Min/max in 0.25dB units */ ah->ah_txpower.txp_min_pwr =2 * rates[7 ]; - ah->ah_txpower.txp_max_pwr =2 * rates[0 ]; + ah->ah_txpower.txp_cur_pwr =2 * rates[0 ]; ah->ah_txpower.txp_ofdm = rates[7 ]; }
@@ -3150,8 +3150,6 @@ ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel,/* Reset TX power values */ memset (&ah->ah_txpower,0 ,sizeof (ah->ah_txpower)); ah->ah_txpower.txp_tpc =AR5K_TUNE_TPC_TXPOWER ; - ah->ah_txpower.txp_min_pwr =0 ; - ah->ah_txpower.txp_max_pwr =AR5K_TUNE_MAX_TXPOWER ;/* Calculate the powertable */ ret = ath5k_setup_channel_powertable(ah, channel,
@@ -3290,7 +3288,8 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,* properly set curve indices. */ ret =ath5k_hw_txpower (ah, channel, ee_mode, - ah->ah_txpower.txp_max_pwr /2 ); + ah->ah_txpower.txp_cur_pwr ? + ah->ah_txpower.txp_cur_pwr /2 :AR5K_TUNE_MAX_TXPOWER );if (ret)return ret;
Re: [PATCH 3/5] ath5k: Track current TX power separately from max TX power
2010/12/21 Bruno Randolf <[email protected]>:
Quoted 55 lines
Add a new variable to keep track of the currently configured tx power. Before
max_pwrwas re-used for keeping the maximum allowed power as well as the current configuration. Doing amin()on it allows you to lower the txpower, but how would you be able to make it higher again?This patch fixes that by adding a new variable
ah_cur_pwrwhich is used instead oftxp_max_pwrto keep the current configuration.txp_max_pwris used to check if we are within the limits.Another problem fixed by this patch is that it avoids setting a zero txpower when things are initialized first and the current power is not yet set.
Signed-off-by Bruno Randolf <[email protected]>---
drivers/net/wireless/ath/ath5k/ath5k.h | 1 +drivers/net/wireless/ath/ath5k/phy.c| 7 +++----2 files changed, 4 insertions(+), 4 deletions(-)drivers/net/wireless/ath/ath5k/ath5k.h +1
-0@@ -1107,6 +1107,7 @@ struct ath5k_hw { /* Values in 0.25dB units */ s16 txp_min_pwr; s16 txp_max_pwr; + s16 txp_cur_pwr; /* Values in 0.5dB units */ s16 txp_offset; s16 txp_ofdm;drivers/net/wireless/ath/ath5k/phy.c +1
-3@@ -3096,7 +3096,7 @@ ath5k_setup_rate_powertable(struct ath5k_hw *ah, u16 max_pwr, /* Min/max in 0.25dB units */ ah->ah_txpower.txp_min_pwr = 2 * rates[7]; - ah->ah_txpower.txp_max_pwr = 2 * rates[0]; + ah->ah_txpower.txp_cur_pwr = 2 * rates[0]; ah->ah_txpower.txp_ofdm = rates[7]; }@@ -3150,8 +3150,6 @@ ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel, /* Reset TX power values */ memset(&ah->ah_txpower, 0, sizeof(ah->ah_txpower)); ah->ah_txpower.txp_tpc = AR5K_TUNE_TPC_TXPOWER; - ah->ah_txpower.txp_min_pwr = 0; - ah->ah_txpower.txp_max_pwr = AR5K_TUNE_MAX_TXPOWER; /* Calculate the powertable */ ret = ath5k_setup_channel_powertable(ah, channel,
drivers/net/wireless/ath/ath5k/phy.c int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel, · line 3295
Quoted 9 lines
drivers/net/wireless/ath/ath5k/phy.c +2
-1@@ -3290,7 +3288,8 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,* properly set curve indices. */ ret = ath5k_hw_txpower(ah, channel, ee_mode, - ah->ah_txpower.txp_max_pwr / 2); + ah->ah_txpower.txp_cur_pwr ? + ah->ah_txpower.txp_cur_pwr / 2 : AR5K_TUNE_MAX_TXPOWER); if (ret) return ret;
Signature · 3 lines
GPG ID: 0xD21DB2DB As you read this post global entropy rises. Have Fun ;-) Nick
PATCH 4/5 ath5k: Remove ATH5K_INI_RFGAIN defines, use band instead
In reply to Bruno RandolfRemove redundant defines.
--- drivers/net/wireless/ath/ath5k/ath5k.h | 6 +----- drivers/net/wireless/ath/ath5k/phy.c | 18 ++++++------------ drivers/net/wireless/ath/ath5k/reset.c | 11 +++-------- 3 files changed, 10 insertions(+), 25 deletions(-)
drivers/net/wireless/ath/ath5k/ath5k.h +1 -5
@@ -154,10 +154,6 @@udelay (1 ); \ }while (0 ) -/* Register dumps are done per operation mode */ -#define AR5K_INI_RFGAIN_5GHZ 0 -#define AR5K_INI_RFGAIN_2GHZ 1 -/* * Some tuneable values (these should be changeable by the user) * TODO: Make use of them and add more options OR use debug/configfs
@@ -1322,7 +1318,7 @@ void ath5k_hw_set_antenna_switch(struct ath5k_hw *ah, u8 ee_mode);int ath5k_hw_set_txpower_limit (struct ath5k_hw *ah,u8 txpower);/* Init function */ int ath5k_hw_phy_init (struct ath5k_hw *ah,struct ieee80211_channel *channel, -u8 mode,u8 ee_mode,u8 freq,bool fast); +u8 mode,u8 ee_mode,bool fast);/* * Functions used internaly
drivers/net/wireless/ath/ath5k/phy.c +6 -12
@@ -609,10 +609,10 @@ done:/* Write initial RF gain table to set the RF sensitivity * this one works on all RF chips and has nothing to do * with gain_F calibration */ -static int ath5k_hw_rfgain_init (struct ath5k_hw *ah,unsigned int freq) +static int ath5k_hw_rfgain_init (struct ath5k_hw *ah,enum ieee80211_band band) {const struct ath5k_ini_rfgain *ath5k_rfg; -unsigned int i, size; +unsigned int i, size, index;switch (ah->ah_radio) {case AR5K_RF5111 :
@@ -644,17 +644,11 @@ static int ath5k_hw_rfgain_init(struct ath5k_hw *ah, unsigned int freq)return -EINVAL ; } -switch (freq) { -case AR5K_INI_RFGAIN_2GHZ : -case AR5K_INI_RFGAIN_5GHZ : -break ; -default : -return -EINVAL ; - } + index = (band ==IEEE80211_BAND_2GHZ ) ?1 :0 ;for (i =0 ; i < size; i++) {AR5K_REG_WAIT (i); -ath5k_hw_reg_write (ah, ath5k_rfg[i].rfg_value[freq], +ath5k_hw_reg_write (ah, ath5k_rfg[i].rfg_value[index], (u32 )ath5k_rfg[i].rfg_register); }
@@ -3246,7 +3240,7 @@ int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 txpower)\*************/ int ath5k_hw_phy_init (struct ath5k_hw *ah,struct ieee80211_channel *channel, -u8 mode,u8 ee_mode,u8 freq,bool fast) +u8 mode,u8 ee_mode,bool fast) {struct ieee80211_channel *curr_channel;int ret, i;
@@ -3305,7 +3299,7 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,* Write initial RF gain settings * This should work for both 5111/5112 */ - ret =ath5k_hw_rfgain_init (ah, freq); + ret =ath5k_hw_rfgain_init (ah, channel->band);if (ret)return ret;
drivers/net/wireless/ath/ath5k/reset.c +3 -8
@@ -1020,13 +1020,12 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, struct ieee80211_channel *channel, bool fast, bool skip_pcu) { u32 s_seq[10], s_led[3], tsf_up, tsf_lo; -u8 mode, freq, ee_mode; +u8 mode, ee_mode;int i, ret; ee_mode =0 ; tsf_up =0 ; tsf_lo =0 ; - freq =0 ; mode =0 ;/*
@@ -1071,7 +1070,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,switch (channel->hw_value &CHANNEL_MODES ) {case CHANNEL_A : mode =AR5K_MODE_11A ; - freq =AR5K_INI_RFGAIN_5GHZ ; ee_mode =AR5K_EEPROM_MODE_11A ;break ;case CHANNEL_G :
@@ -1083,7 +1081,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, } mode =AR5K_MODE_11G ; - freq =AR5K_INI_RFGAIN_2GHZ ; ee_mode =AR5K_EEPROM_MODE_11G ;break ;case CHANNEL_B :
@@ -1095,7 +1092,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, } mode =AR5K_MODE_11B ; - freq =AR5K_INI_RFGAIN_2GHZ ; ee_mode =AR5K_EEPROM_MODE_11B ;break ;case CHANNEL_XR :
@@ -1105,7 +1101,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,return -EINVAL ; } mode =AR5K_MODE_XR ; - freq =AR5K_INI_RFGAIN_5GHZ ; ee_mode =AR5K_EEPROM_MODE_11A ;break ;default :
@@ -1120,7 +1115,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,*/ if (fast) { ret =ath5k_hw_phy_init (ah, channel, mode, - ee_mode, freq, true); + ee_mode, true);if (ret) {ATH5K_DBG (ah->ah_sc,ATH5K_DEBUG_RESET ,"fast chan change failed, falling back to normal reset\n" );
@@ -1256,7 +1251,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,/* * Initialize PHY */ - ret =ath5k_hw_phy_init (ah, channel, mode, ee_mode, freq, false); + ret =ath5k_hw_phy_init (ah, channel, mode, ee_mode, false);if (ret) {ATH5K_ERR (ah->ah_sc,"failed to initialize PHY (%i) !\n" , ret);
Re: [PATCH 4/5] ath5k: Remove ATH5K_INI_RFGAIN defines, use band instead
2010/12/21 Bruno Randolf <[email protected]>:
Quoted 151 lines
Remove redundant defines.
Signed-off-by Bruno Randolf <[email protected]>---
drivers/net/wireless/ath/ath5k/ath5k.h | 6 +-----drivers/net/wireless/ath/ath5k/phy.c| 18 ++++++------------drivers/net/wireless/ath/ath5k/reset.c| 11 +++--------3 files changed, 10 insertions(+), 25 deletions(-)drivers/net/wireless/ath/ath5k/ath5k.h +1
-5@@ -154,10 +154,6 @@ udelay(1); \ } while (0) -/* Register dumps are done per operation mode */ -#define AR5K_INI_RFGAIN_5GHZ 0 -#define AR5K_INI_RFGAIN_2GHZ 1 - /** Some tuneable values (these should be changeable by the user) * TODO: Make use of them and add more options OR use debug/configfs @@ -1322,7 +1318,7 @@ void ath5k_hw_set_antenna_switch(struct ath5k_hw *ah, u8 ee_mode); int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 txpower); /* Init function */ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel, - u8 mode, u8 ee_mode, u8 freq, bool fast); + u8 mode, u8 ee_mode, bool fast); /** Functions used internaly drivers/net/wireless/ath/ath5k/phy.c +2
-2@@ -609,10 +609,10 @@ done: /* Write initial RF gain table to set the RF sensitivity* this one works on all RF chips and has nothing to do * with gain_F calibration */ -static int ath5k_hw_rfgain_init (struct ath5k_hw *ah,unsigned int freq) +static int ath5k_hw_rfgain_init (struct ath5k_hw *ah,enum ieee80211_band band) { const struct ath5k_ini_rfgain *ath5k_rfg; - unsigned int i, size; + unsigned int i, size, index; switch (ah->ah_radio) {case
AR5K_RF5111:drivers/net/wireless/ath/ath5k/phy.c +2
-8@@ -644,17 +644,11 @@ static int ath5k_hw_rfgain_init(struct ath5k_hw *ah, unsigned int freq) return -EINVAL; } - switch (freq) { - case AR5K_INI_RFGAIN_2GHZ: - case AR5K_INI_RFGAIN_5GHZ: - break; - default: - return -EINVAL; - } + index = (band == IEEE80211_BAND_2GHZ) ? 1 : 0; for (i = 0; i < size; i++) { AR5K_REG_WAIT(i); - ath5k_hw_reg_write(ah, ath5k_rfg[i].rfg_value[freq], + ath5k_hw_reg_write(ah, ath5k_rfg[i].rfg_value[index], (u32)ath5k_rfg[i].rfg_register); }@@ -3246,7 +3240,7 @@ int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 txpower)\*************/
int ath5k_hw_phy_init(struct
ath5k_hw*ah, structieee80211_channel*channel,
- u8 mode, u8ee_mode, u8 freq, bool fast)
+ u8 mode, u8ee_mode, bool fast)
{
structieee80211_channel*curr_channel;
int ret, i;drivers/net/wireless/ath/ath5k/phy.c +1
-1@@ -3305,7 +3299,7 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,* Write initial RF gain settings * This should work for both 5111/5112 */ - ret = ath5k_hw_rfgain_init(ah, freq); + ret = ath5k_hw_rfgain_init(ah, channel->band); if (ret) return ret;drivers/net/wireless/ath/ath5k/reset.c +1
-2@@ -1020,13 +1020,12 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, struct ieee80211_channel *channel, bool fast, bool skip_pcu) { u32 s_seq[10], s_led[3], tsf_up, tsf_lo; - u8 mode, freq, ee_mode; + u8 mode, ee_mode; int i, ret; ee_mode = 0; tsf_up = 0; tsf_lo = 0; - freq = 0; mode = 0; /*@@ -1071,7 +1070,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, switch (channel->hw_value & CHANNEL_MODES) {case
CHANNEL_A:
mode =AR5K_MODE_11A;
- freq =AR5K_INI_RFGAIN_5GHZ;
ee_mode =AR5K_EEPROM_MODE_11A;
break;
caseCHANNEL_G:drivers/net/wireless/ath/ath5k/reset.c +0
-1@@ -1083,7 +1081,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, } mode = AR5K_MODE_11G; - freq = AR5K_INI_RFGAIN_2GHZ; ee_mode = AR5K_EEPROM_MODE_11G; break;case
CHANNEL_B:drivers/net/wireless/ath/ath5k/reset.c +0
-1@@ -1095,7 +1092,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, } mode = AR5K_MODE_11B; - freq = AR5K_INI_RFGAIN_2GHZ; ee_mode = AR5K_EEPROM_MODE_11B; break;case
CHANNEL_XR:drivers/net/wireless/ath/ath5k/reset.c +0
-1@@ -1105,7 +1101,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, return -EINVAL; } mode = AR5K_MODE_XR; - freq = AR5K_INI_RFGAIN_5GHZ; ee_mode = AR5K_EEPROM_MODE_11A; break;default:
drivers/net/wireless/ath/ath5k/reset.c +1
-1@@ -1120,7 +1115,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,*/ if (fast) { ret = ath5k_hw_phy_init(ah, channel, mode, - ee_mode, freq, true); + ee_mode, true); if (ret) { ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_RESET, "fast chan change failed, falling back to normal reset\n");
drivers/net/wireless/ath/ath5k/reset.c int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, · line 1257
Quoted 8 lines
drivers/net/wireless/ath/ath5k/reset.c +1
-1@@ -1256,7 +1251,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, /* * Initialize PHY */ - ret = ath5k_hw_phy_init(ah, channel, mode, ee_mode, freq, false); + ret = ath5k_hw_phy_init(ah, channel, mode, ee_mode, false); if (ret) { ATH5K_ERR(ah->ah_sc, "failed to initialize PHY (%i) !\n", ret);
Signature · 3 lines
GPG ID: 0xD21DB2DB As you read this post global entropy rises. Have Fun ;-) Nick
PATCH 5/5 ath5k: Use helper function to get eeprom mode from channel
In reply to Bruno RandolfIntroduce a helper function to get the EEPROM mode from channel and remove multiple similar switch statements. Also since it's now easy to get the EEPROM mode from the channel, use them inside the functions which need it, instead of passing a redundant ee_mode parameter.
--- drivers/net/wireless/ath/ath5k/ath5k.h | 2 - drivers/net/wireless/ath/ath5k/eeprom.c | 16 +++++++ drivers/net/wireless/ath/ath5k/eeprom.h | 2 + drivers/net/wireless/ath/ath5k/phy.c | 68 +++++++------------------------ drivers/net/wireless/ath/ath5k/reset.c | 19 ++++----- 5 files changed, 42 insertions(+), 65 deletions(-)
drivers/net/wireless/ath/ath5k/ath5k.h +1 -1
@@ -1318,7 +1318,7 @@ void ath5k_hw_set_antenna_switch(struct ath5k_hw *ah, u8 ee_mode);int ath5k_hw_set_txpower_limit (struct ath5k_hw *ah,u8 txpower);/* Init function */ int ath5k_hw_phy_init (struct ath5k_hw *ah,struct ieee80211_channel *channel, -u8 mode,u8 ee_mode,bool fast); +u8 mode,bool fast);/* * Functions used internaly
drivers/net/wireless/ath/ath5k/eeprom.c +16 -0
@@ -1802,3 +1802,19 @@ ath5k_eeprom_detach(struct ath5k_hw *ah)for (mode =AR5K_EEPROM_MODE_11A ; mode <=AR5K_EEPROM_MODE_11G ; mode++)ath5k_eeprom_free_pcal_info (ah, mode); } + +int +ath5k_eeprom_mode_from_channel (struct ieee80211_channel *channel) +{ +switch (channel->hw_value &CHANNEL_MODES ) { +case CHANNEL_A : +case CHANNEL_XR : +return AR5K_EEPROM_MODE_11A ; +case CHANNEL_G : +return AR5K_EEPROM_MODE_11G ; +case CHANNEL_B : +return AR5K_EEPROM_MODE_11B ; +default : +return -1 ; + } +}
drivers/net/wireless/ath/ath5k/eeprom.h +2 -0
@@ -517,3 +517,5 @@ struct ath5k_eeprom_info {u32 ee_antenna[AR5K_EEPROM_N_MODES ][AR5K_ANT_MAX ]; }; +int +ath5k_eeprom_mode_from_channel (struct ieee80211_channel *channel);
drivers/net/wireless/ath/ath5k/phy.c +15 -53
116 lines not on this page · raw message
drivers/net/wireless/ath/ath5k/reset.c +8 -11
@@ -866,15 +866,18 @@ static void ath5k_hw_tweak_initval_settings(struct ath5k_hw *ah, }static void ath5k_hw_commit_eeprom_settings (struct ath5k_hw *ah, -struct ieee80211_channel *channel,u8 ee_mode) +struct ieee80211_channel *channel) {struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;s16 cck_ofdm_pwr_delta; +u8 ee_mode;/* TODO: Add support for AR5210 EEPROM */ if (ah->ah_version ==AR5K_AR5210 )return ; + ee_mode =ath5k_eeprom_mode_from_channel (channel); +/* Adjust power delta for channel 14 */ if (channel->center_freq ==2484 ) cck_ofdm_pwr_delta =
@@ -1020,10 +1023,9 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, struct ieee80211_channel *channel, bool fast, bool skip_pcu) { u32 s_seq[10], s_led[3], tsf_up, tsf_lo; -u8 mode, ee_mode; +u8 mode;int i, ret; - ee_mode =0 ; tsf_up =0 ; tsf_lo =0 ; mode =0 ;
@@ -1070,7 +1072,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,switch (channel->hw_value &CHANNEL_MODES ) {case CHANNEL_A : mode =AR5K_MODE_11A ; - ee_mode =AR5K_EEPROM_MODE_11A ;break ;case CHANNEL_G :
@@ -1081,7 +1082,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, } mode =AR5K_MODE_11G ; - ee_mode =AR5K_EEPROM_MODE_11G ;break ;case CHANNEL_B :
@@ -1092,7 +1092,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, } mode =AR5K_MODE_11B ; - ee_mode =AR5K_EEPROM_MODE_11B ;break ;case CHANNEL_XR :if (ah->ah_version ==AR5K_AR5211 ) {
@@ -1101,7 +1100,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,return -EINVAL ; } mode =AR5K_MODE_XR ; - ee_mode =AR5K_EEPROM_MODE_11A ;break ;default : ATH5K_ERR(ah->ah_sc,
@@ -1114,8 +1112,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,* go on. If it fails continue with a normal reset. */ if (fast) { - ret =ath5k_hw_phy_init (ah, channel, mode, - ee_mode, true); + ret =ath5k_hw_phy_init (ah, channel, mode, true);if (ret) {ATH5K_DBG (ah->ah_sc,ATH5K_DEBUG_RESET ,"fast chan change failed, falling back to normal reset\n" );
@@ -1212,7 +1209,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,ath5k_hw_tweak_initval_settings (ah, channel);/* Commit values from EEPROM */ -ath5k_hw_commit_eeprom_settings (ah, channel, ee_mode); +ath5k_hw_commit_eeprom_settings (ah, channel);/*
@@ -1251,7 +1248,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,/* * Initialize PHY */ - ret =ath5k_hw_phy_init (ah, channel, mode, ee_mode, false); + ret =ath5k_hw_phy_init (ah, channel, mode, false);if (ret) {ATH5K_ERR (ah->ah_sc,"failed to initialize PHY (%i) !\n" , ret);
Re: [PATCH 5/5] ath5k: Use helper function to get eeprom mode from channel
2010/12/21 Bruno Randolf <[email protected]>:
Quoted 278 lines
Introduce a helper function to get the EEPROM mode from channel and remove multiple similar switch statements. Also since it's now easy to get the EEPROM mode from the channel, use them inside the functions which need it, instead of passing a redundant
ee_modeparameter.Signed-off-by Bruno Randolf <[email protected]>---
drivers/net/wireless/ath/ath5k/ath5k.h | 2 -drivers/net/wireless/ath/ath5k/eeprom.c| 16 +++++++drivers/net/wireless/ath/ath5k/eeprom.h| 2 +drivers/net/wireless/ath/ath5k/phy.c| 68 +++++++------------------------drivers/net/wireless/ath/ath5k/reset.c| 19 ++++-----5 files changed, 42 insertions(+), 65 deletions(-)drivers/net/wireless/ath/ath5k/ath5k.h +1
-1@@ -1318,7 +1318,7 @@ void ath5k_hw_set_antenna_switch(struct ath5k_hw *ah, u8 ee_mode); int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 txpower); /* Init function */ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel, - u8 mode, u8 ee_mode, bool fast); + u8 mode, bool fast); /** Functions used internaly drivers/net/wireless/ath/ath5k/eeprom.c +16
-0@@ -1802,3 +1802,19 @@ ath5k_eeprom_detach(struct ath5k_hw *ah) for (mode = AR5K_EEPROM_MODE_11A; mode <= AR5K_EEPROM_MODE_11G; mode++) ath5k_eeprom_free_pcal_info(ah, mode); } + +int +ath5k_eeprom_mode_from_channel (struct ieee80211_channel *channel) +{ + switch (channel->hw_value & CHANNEL_MODES) { + case CHANNEL_A: + case CHANNEL_XR: + return AR5K_EEPROM_MODE_11A; + case CHANNEL_G: + return AR5K_EEPROM_MODE_11G; + case CHANNEL_B: + return AR5K_EEPROM_MODE_11B; + default: + return -1; + } +}drivers/net/wireless/ath/ath5k/eeprom.h +2
-0@@ -517,3 +517,5 @@ struct ath5k_eeprom_info { u32 ee_antenna[AR5K_EEPROM_N_MODES][AR5K_ANT_MAX]; }; +int +ath5k_eeprom_mode_from_channel (struct ieee80211_channel *channel);drivers/net/wireless/ath/ath5k/phy.c +3
-26@@ -1355,20 +1355,7 @@ void ath5k_hw_update_noise_floor(struct ath5k_hw *ah) return; } - switch (ah->ah_current_channel->hw_value & CHANNEL_MODES) { - case CHANNEL_A: - case CHANNEL_XR: - ee_mode = AR5K_EEPROM_MODE_11A; - break; - case CHANNEL_G: - ee_mode = AR5K_EEPROM_MODE_11G; - break; - default: - case CHANNEL_B: - ee_mode = AR5K_EEPROM_MODE_11B; - break; - } - + ee_mode = ath5k_eeprom_mode_from_channel(ah->ah_current_channel); /* completed NF calibration, test threshold */ nf = ath5k_hw_read_measured_noise_floor(ah);@@ -1941,18 +1928,8 @@ ath5k_hw_set_antenna_mode(struct ath5k_hw *ah, u8 ant_mode) def_ant = ah->ah_def_ant; - switch (channel->hw_value & CHANNEL_MODES) { - case CHANNEL_A: - case CHANNEL_XR: - ee_mode = AR5K_EEPROM_MODE_11A; - break; - case CHANNEL_G: - ee_mode = AR5K_EEPROM_MODE_11G; - break; - case CHANNEL_B: - ee_mode = AR5K_EEPROM_MODE_11B; - break; - default: + ee_mode = ath5k_eeprom_mode_from_channel(channel); + if (ee_mode < 0) { ATH5K_ERR(ah->ah_sc, "invalid channel: %d\n", channel->center_freq); return;@@ -3100,11 +3077,11 @@ ath5k_setup_rate_powertable(struct ath5k_hw *ah, u16 max_pwr,*/ static int
ath5k_hw_txpower(structath5k_hw*ah, structieee80211_channel*channel,
- u8ee_mode, u8 txpower)
+ u8 txpower)
{
structath5k_rate_pcal_inforate_info;
structieee80211_channel*curr_channel=ah->ah_current_channel;
- u8 type;
+ u8 type,ee_mode;
int ret;if (txpower >
AR5K_TUNE_MAX_TXPOWER) {drivers/net/wireless/ath/ath5k/phy.c +7
-0@@ -3112,6 +3089,13 @@ ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel, return -EINVAL; } + ee_mode = ath5k_eeprom_mode_from_channel(channel); + if (ee_mode < 0) { + ATH5K_ERR(ah->ah_sc, + "invalid channel: %d\n", channel->center_freq); + return -EINVAL; + } + /* Initialize TX power table */ switch (ah->ah_radio) {case
AR5K_RF5110:drivers/net/wireless/ath/ath5k/phy.c +1
-22@@ -3208,31 +3192,10 @@ ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel, int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 txpower) { - /*Just a try M.F.*/ - struct ieee80211_channel *channel = ah->ah_current_channel; - u8 ee_mode; - - switch (channel->hw_value & CHANNEL_MODES) { - case CHANNEL_A: - case CHANNEL_XR: - ee_mode = AR5K_EEPROM_MODE_11A; - break; - case CHANNEL_G: - ee_mode = AR5K_EEPROM_MODE_11G; - break; - case CHANNEL_B: - ee_mode = AR5K_EEPROM_MODE_11B; - break; - default: - ATH5K_ERR(ah->ah_sc, - "invalid channel: %d\n", channel->center_freq); - return -EINVAL; - } - ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_TXPOWER, "changing txpower to %d\n", txpower); - return ath5k_hw_txpower(ah, channel, ee_mode, txpower); + return ath5k_hw_txpower(ah, ah->ah_current_channel, txpower); } /*************\@@ -3240,7 +3203,7 @@ int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 txpower)\*************/
int ath5k_hw_phy_init(struct
ath5k_hw*ah, structieee80211_channel*channel,
- u8 mode, u8ee_mode, bool fast)
+ u8 mode, bool fast)
{
structieee80211_channel*curr_channel;
int ret, i;drivers/net/wireless/ath/ath5k/phy.c +1
-2@@ -3281,8 +3244,7 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,* RF buffer settings on 5211/5212+ so that we * properly set curve indices. */ - ret = ath5k_hw_txpower(ah, channel, ee_mode, - ah->ah_txpower.txp_cur_pwr ? + ret = ath5k_hw_txpower(ah, channel, ah->ah_txpower.txp_cur_pwr ? ah->ah_txpower.txp_cur_pwr / 2 : AR5K_TUNE_MAX_TXPOWER); if (ret) return ret;drivers/net/wireless/ath/ath5k/reset.c +4
-1@@ -866,15 +866,18 @@ static void ath5k_hw_tweak_initval_settings(struct ath5k_hw *ah, } static void ath5k_hw_commit_eeprom_settings(struct ath5k_hw *ah, - struct ieee80211_channel *channel, u8 ee_mode) + struct ieee80211_channel *channel) { struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; s16 cck_ofdm_pwr_delta; + u8 ee_mode; /* TODO: Add support for AR5210 EEPROM */ if (ah->ah_version == AR5K_AR5210) return; + ee_mode = ath5k_eeprom_mode_from_channel(channel); + /* Adjust power delta for channel 14 */ if (channel->center_freq == 2484)cck_ofdm_pwr_delta =
drivers/net/wireless/ath/ath5k/reset.c +1
-2@@ -1020,10 +1023,9 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, struct ieee80211_channel *channel, bool fast, bool skip_pcu) { u32 s_seq[10], s_led[3], tsf_up, tsf_lo; - u8 mode, ee_mode; + u8 mode; int i, ret; - ee_mode = 0; tsf_up = 0; tsf_lo = 0; mode = 0;@@ -1070,7 +1072,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, switch (channel->hw_value & CHANNEL_MODES) {case
CHANNEL_A:
mode =AR5K_MODE_11A;
-ee_mode=AR5K_EEPROM_MODE_11A;
break;
caseCHANNEL_G:drivers/net/wireless/ath/ath5k/reset.c +0
-1@@ -1081,7 +1082,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, } mode = AR5K_MODE_11G; - ee_mode = AR5K_EEPROM_MODE_11G; break;case
CHANNEL_B:drivers/net/wireless/ath/ath5k/reset.c +0
-1@@ -1092,7 +1092,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, } mode = AR5K_MODE_11B; - ee_mode = AR5K_EEPROM_MODE_11B; break;case
CHANNEL_XR:
if (ah->ah_version==AR5K_AR5211) {drivers/net/wireless/ath/ath5k/reset.c +0
-1@@ -1101,7 +1100,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, return -EINVAL; } mode = AR5K_MODE_XR; - ee_mode = AR5K_EEPROM_MODE_11A; break;default:
ATH5K_ERR(ah->ah_sc,drivers/net/wireless/ath/ath5k/reset.c +2
-3@@ -1114,8 +1112,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,* go on. If it fails continue with a normal reset. */ if (fast) { - ret = ath5k_hw_phy_init(ah, channel, mode, - ee_mode, true); + ret = ath5k_hw_phy_init(ah, channel, mode, true); if (ret) { ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_RESET, "fast chan change failed, falling back to normal reset\n");@@ -1212,7 +1209,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, ath5k_hw_tweak_initval_settings(ah, channel); /* Commit values from EEPROM */ - ath5k_hw_commit_eeprom_settings(ah, channel, ee_mode); + ath5k_hw_commit_eeprom_settings(ah, channel); /*
drivers/net/wireless/ath/ath5k/reset.c int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, · line 1254
Quoted 8 lines
drivers/net/wireless/ath/ath5k/reset.c +1
-1@@ -1251,7 +1248,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, /* * Initialize PHY */ - ret = ath5k_hw_phy_init(ah, channel, mode, ee_mode, false); + ret = ath5k_hw_phy_init(ah, channel, mode, false); if (ret) { ATH5K_ERR(ah->ah_sc, "failed to initialize PHY (%i) !\n", ret);
Signature · 3 lines
GPG ID: 0xD21DB2DB As you read this post global entropy rises. Have Fun ;-) Nick
2010/12/21 Bruno Randolf <[email protected]>:
Quoted 111 lines
Let
ath5k_hw_txpower()decide if it can re-use the powertable or if it has to be recalculated instead of passing a 'fast' flag from the outside.Signed-off-by Bruno Randolf <[email protected]>---
drivers/net/wireless/ath/ath5k/ath5k.h | 1 +drivers/net/wireless/ath/ath5k/phy.c| 35 ++++++++++++--------------------2 files changed, 14 insertions(+), 22 deletions(-)drivers/net/wireless/ath/ath5k/ath5k.h +1
-0@@ -1113,6 +1113,7 @@ struct ath5k_hw { s16 txp_cck_ofdm_gainf_delta; /* Value in dB units */ s16 txp_cck_ofdm_pwr_delta; + bool txp_setup; } ah_txpower; struct {drivers/net/wireless/ath/ath5k/phy.c +2
-0@@ -3004,6 +3004,8 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah, return -EINVAL; } + ah->ah_txpower.txp_setup = true; + return 0; }@@ -3105,9 +3107,10 @@ ath5k_setup_rate_powertable(struct ath5k_hw *ah, u16 max_pwr,*/ static int
ath5k_hw_txpower(structath5k_hw*ah, structieee80211_channel*channel,
- u8ee_mode, u8 txpower, bool fast)
+ u8ee_mode, u8 txpower)
{
structath5k_rate_pcal_inforate_info;
+ structieee80211_channel*curr_channel=ah->ah_current_channel; u8 type;
int ret;drivers/net/wireless/ath/ath5k/phy.c +7
-4@@ -3138,10 +3141,13 @@ ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel, return -EINVAL; } - /* If fast is set it means we are on the same channel/mode - * so there is no need to recalculate the powertable, we 'll - * just use the cached one */ - if (!fast) { + /* + * If we don't change channel/mode skip tx powertable calculation + * and use the cached one. + */ + if (!ah->ah_txpower.txp_setup || + (channel->hw_value != curr_channel->hw_value) || + (channel->center_freq != curr_channel->center_freq)) { /* Reset TX power values */ memset(&ah->ah_txpower, 0, sizeof(ah->ah_txpower)); ah->ah_txpower.txp_tpc = AR5K_TUNE_TPC_TXPOWER;@@ -3159,8 +3165,6 @@ ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel,else
ath5k_setup_pcdac_table(ah);drivers/net/wireless/ath/ath5k/phy.c +0
-2- -/* Limit max power if we have a CTL available */
ath5k_get_max_ctl_power(ah, channel);drivers/net/wireless/ath/ath5k/phy.c +1
-13@@ -3238,7 +3242,7 @@ int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 txpower) ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_TXPOWER, "changing txpower to %d\n", txpower); - return ath5k_hw_txpower(ah, channel, ee_mode, txpower, true); + return ath5k_hw_txpower(ah, channel, ee_mode, txpower); } /*************\@@ -3251,7 +3255,6 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel, struct ieee80211_channel *curr_channel; int ret, i; u32 phy_tst1; - bool fast_txp; ret = 0; /*@@ -3282,17 +3285,6 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel, } /* - * If we don't change channel/mode skip - * tx powertable calculation and use the - * cached one. - */ - if ((channel->hw_value == curr_channel->hw_value) && - (channel->center_freq == curr_channel->center_freq)) - fast_txp = true; - else - fast_txp = false; - - /** Set TX power * * Note: We need to do that before we set
drivers/net/wireless/ath/ath5k/phy.c int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel, · line 3298
Quoted 9 lines
drivers/net/wireless/ath/ath5k/phy.c +1
-2@@ -3300,8 +3292,7 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,* properly set curve indices. */ ret = ath5k_hw_txpower(ah, channel, ee_mode, - ah->ah_txpower.txp_max_pwr / 2, - fast_txp); + ah->ah_txpower.txp_max_pwr / 2); if (ret) return ret;
Signature · 3 lines
GPG ID: 0xD21DB2DB As you read this post global entropy rises. Have Fun ;-) Nick