Skip to contentSkip to conversation

fix i810 i2c bug

PATCH Applied Stefani Seibold 2 participants 2 messages Jan 3, 2011 – Jan 6, 2011 Framebuffer layer

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 fix i810 i2c bug

These patch fix a longstanding bug in the i810 frame buffer driver.

The handling of the i2c bus is wrong: A 1 bit should not written to the i2c, these will be done by switch the i2c to input. Driving an 1 bit active is against the i2c spec.

An active driven of a 1 bit will result in very strange error, depending which side is the more powerful one. In my case it depends on the temperature of the Display-Controller-EEprom: With an cold eprom a got the correct EDID datas, with a warm one some of the 1 bits was 0 :-(

The same bug is also in the intelfb driver in the file drivers/video/intelfb/intelfb_i2c.c. The functions intelfb_gpio_setscl() and intelfb_gpio_setsda() do drive the 1 bit active to the i2c bus. But since i have no card which is used by the intelfb driver i cannot fix it.

The patch is against linux next-20101231

- Stefani

---
 i810-i2c.c |   12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)
drivers/video/i810/i810-i2c.c +8 -4
diff -u -N -r -p linux-2.6.35.orig/drivers/video/i810/i810-i2c.c linux-2.6.35/drivers/video/i810/i810-i2c.c
@@ -45,8 +45,10 @@ static void i810i2c_setscl(void *data, i
         struct i810fb_par         *par = chan->par;
 	u8                        __iomem *mmio = par->mmio_start_virtual;
 
-	i810_writel(mmio, chan->ddc_base, (state ? SCL_VAL_OUT : 0) | SCL_DIR |
-		    SCL_DIR_MASK | SCL_VAL_MASK);
+	if (state)
+		i810_writel(mmio, chan->ddc_base, SCL_DIR_MASK | SCL_VAL_MASK);
+	else
+		i810_writel(mmio, chan->ddc_base, SCL_DIR | SCL_DIR_MASK | SCL_VAL_MASK);
 	i810_readl(mmio, chan->ddc_base);	/* flush posted write */
 }
 
@@ -56,8 +58,10 @@ static void i810i2c_setsda(void *data, i
         struct i810fb_par         *par = chan->par;
 	u8                        __iomem *mmio = par->mmio_start_virtual;
 
- 	i810_writel(mmio, chan->ddc_base, (state ? SDA_VAL_OUT : 0) | SDA_DIR |
-		    SDA_DIR_MASK | SDA_VAL_MASK);
+	if (state)
+		i810_writel(mmio, chan->ddc_base, SDA_DIR_MASK | SDA_VAL_MASK);
+	else
+		i810_writel(mmio, chan->ddc_base, SDA_DIR | SDA_DIR_MASK | SDA_VAL_MASK);
 	i810_readl(mmio, chan->ddc_base);	/* flush posted write */
 }
 
Applied
#1 lore raw
Quoted 17 lines · Stefani Seibold

These patch fix a longstanding bug in the i810 frame buffer driver.

The handling of the i2c bus is wrong: A 1 bit should not written to the i2c, these will be done by switch the i2c to input. Driving an 1 bit active is against the i2c spec.

An active driven of a 1 bit will result in very strange error, depending which side is the more powerful one. In my case it depends on the temperature of the Display-Controller-EEprom: With an cold eprom a got the correct EDID datas, with a warm one some of the 1 bits was 0 :-(

The same bug is also in the intelfb driver in the file drivers/video/intelfb/intelfb_i2c.c. The functions intelfb_gpio_setscl() and intelfb_gpio_setsda() do drive the 1 bit active to the i2c bus. But since i have no card which is used by the intelfb driver i cannot fix it.

Quoted 5 lines

The patch is against linux next-20101231

- Stefani

Applied, thanks.

Also adding intelfb people to the Cc so they're aware of the problem, and can follow suit.