bma023: Support for Bosch BMA023 and SMB380 accelerometers

new file mode 100644
index 0000000..04a293c
@@ -0,0 +1,93 @@
+*Note*: It is anticpated that if IIO ever makes it upstream that the
+preferred general purpose non-input interface to this hardware will become IIO.
+
+What:		/sys/bus/i2c/devices/<busnum>-<devaddr>/range
+Date:		February 2011
+Contact:	Alan Cox <[email protected]>
+Description:	Configure the sensing range of the device
+		0: +/- 2G
+		1: +/- 4G
+		2: +/- 8G
+
+What:		/sys/bus/i2c/devices/<busnum>-<devaddr>/bandwidth
+Date:		February 2011
+Contact:	Alan Cox <[email protected]>
+Description:	Digital filtering on ADC output data
+		0: 25Hz
+		1: 50Hz
+		2: 100Hz
+		3: 190Hz
+		4: 375Hz
+		5: 750Hz
+		6: 1500Hz
+
+What:		/sys/bus/i2c/devices/<busnum>-<devaddr>/new_data_int
+Date:		February 2011
+Contact:	Alan Cox <[email protected]>
+Description:	Generate an interrupt when the axes values are changed
+		0: disable
+		1: enable
+
+What:		/sys/bus/i2c/devices/<busnum>-<devaddr>/hg_int
+Date:		February 2011
+Contact:	Alan Cox <[email protected]>
+Description:	Generate an interrupt when the high-g threshold is met
+		0: disable
+		1: enable
+
+What:		/sys/bus/i2c/devices/<busnum>-<devaddr>/lg_int
+Date:		February 2011
+Contact:	Alan Cox <[email protected]>
+Description:	Generate an interrupt when the low-g threshold is met
+		0: disable
+		1: enable
+
+What:		/sys/bus/i2c/devices/<busnum>-<devaddr>/hg_dur
+Date:		February 2011
+Contact:	Alan Cox <[email protected]>
+Description:	High G duration required to trigger.
+		(See the equations in the data sheet)
+
+What:		/sys/bus/i2c/devices/<busnum>-<devaddr>/hg_hyst
+Date:		February 2011
+Contact:	Alan Cox <[email protected]>
+Description:	High G duration hysteresis
+		(See the equations in the data sheet)
+
+What:		/sys/bus/i2c/devices/<busnum>-<devaddr>/hg_thres
+Date:		February 2011
+Contact:	Alan Cox <[email protected]>
+Description:	High G threshold
+		(See the equations in the data sheet)
+
+What:		/sys/bus/i2c/devices/<busnum>-<devaddr>/lg_dur
+Date:		February 2011
+Contact:	Alan Cox <[email protected]>
+Description:	Low G duration required to trigger
+		(See the equations in the data sheet)
+
+What:		/sys/bus/i2c/devices/<busnum>-<devaddr>/lg_hyst
+Date:		February 2011
+Contact:	Alan Cox <[email protected]>
+Description:	Low G duration hysteresis
+		(See the equations in the data sheet)
+
+What:		/sys/bus/i2c/devices/<busnum>-<devaddr>/lg_thres
+Date:		February 2011
+Contact:	Alan Cox <[email protected]>
+Description:	Low G threshold
+		(See the equations in the data sheet)
+
+What:		/sys/bus/i2c/devices/<busnum>-<devaddr>/power_mode
+Date:		February 2011
+Contact:	Alan Cox <[email protected]>
+Description:	Power mode
+		0: Use runtime PM
+		1: Forced on
+
+What:		/sys/bus/i2c/devices/<busnum>-<devaddr>/accel_data
+Date:		February 2011
+Contact:	Alan Cox <[email protected]>
+Description:	Raw XYZ co-ordinate data, each ranges from -512 to +511,
+		formatted as (x,y,z) to match existing similar interfaces
+

index b0c6772..3b595b8 100644
@@ -454,4 +454,14 @@ config INPUT_CMA3000_I2C
 	  To compile this driver as a module, choose M here: the
 	  module will be called cma3000_d0x_i2c.
 
+config INPUT_BMA023
+	tristate "BMA023/SMB380 Triaxial acceleration sensor"
+	depends on I2C
+	help
+	  Say Y here if you want to support Bosch BMA023/SMB380
+	  connected via an I2C bus.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called bma023.
+
 endif

index 9b47971..79b3f66 100644
@@ -36,6 +36,7 @@ obj-$(CONFIG_INPUT_PWM_BEEPER)		+= pwm-beeper.o
 obj-$(CONFIG_INPUT_RB532_BUTTON)	+= rb532_button.o
 obj-$(CONFIG_INPUT_GPIO_ROTARY_ENCODER)	+= rotary_encoder.o
 obj-$(CONFIG_INPUT_SGI_BTNS)		+= sgi_btns.o
+obj-$(CONFIG_INPUT_BMA023)			+= bma023.o
 obj-$(CONFIG_INPUT_SPARCSPKR)		+= sparcspkr.o
 obj-$(CONFIG_INPUT_TWL4030_PWRBUTTON)	+= twl4030-pwrbutton.o
 obj-$(CONFIG_INPUT_TWL4030_VIBRA)	+= twl4030-vibra.o