Skip to contentSkip to conversation

Using CONFIG_PHYSICAL_START

DISCUSSION Meador Inge 2 participants 3 messages Feb 16, 2011

lore
Share & tools
lore
#0 lore raw

Hi Kumar,

Quick question about the support for booting at a non-zero base address (as committed here: http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=37dd2badcfcec35f5e21a0926968d77a404f03c3).
Is booting from a non-zero address as simple as changing
"CONFIG_PHYSICAL_START" (assuming it meets the alignment constraints, of course)?

For example, I want to boot from a non-zero address on the P1022DS. I should just be able to change "CONFIG_PHYSICAL_START" to, say, 0x08000000, and it should work, right? Any other bits that need to be done (i.e. U-Boot or device tree magic)?

Signature · 2 lines
Meador Inge     | meador_inge AT mentor.com
Mentor Embedded | http://www.mentor.com/embedded-software
#1 lore raw
Quoted 8 lines · On Wed, 16 Feb 2011 12:00:25 -0600 Meador Inge <[email protected]> wrote:

Hi Kumar,

Quick question about the support for booting at a non-zero base address (as committed here:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=37dd2badcfcec35f5e21a0926968d77a404f03c3).
Is booting from a non-zero address as simple as changing
"CONFIG_PHYSICAL_START" (assuming it meets the alignment constraints, of course)?

Another option is to turn on CONFIG_RELOCATABLE. Note that you'll still have the same alignment constraints; it doesn't generate a truly relocatable binary (the effective addresses are fixed). But you don't have to specify the physical address at compile-time. This allows you to use the same kernel image for multiple AMP partitions.

Quoted 4 lines

For example, I want to boot from a non-zero address on the P1022DS. I should just be able to change "CONFIG_PHYSICAL_START" to, say, 0x08000000, and it should work, right? Any other bits that need to be done (i.e. U-Boot or device tree magic)?

You'll want the memory node adjusted for your restricted address range (I'm assuming that this is why you want to start at non-zero, and that you're not trying to have the kernel be located in the middle of its partition).

There are some special u-boot variables (bootm_low/bootm_size) that govern placement of the kernel, fdt, etc.

-Scott

#2 lore raw
Quoted 23 lines · Scott Wood
Quoted 8 lines · On Wed, 16 Feb 2011 12:00:25 -0600 Meador Inge<[email protected]> wrote:

Hi Kumar,

Quick question about the support for booting at a non-zero base address (as committed here:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=37dd2badcfcec35f5e21a0926968d77a404f03c3).
Is booting from a non-zero address as simple as changing
"CONFIG_PHYSICAL_START" (assuming it meets the alignment constraints, of course)?

Another option is to turn on CONFIG_RELOCATABLE. Note that you'll still have the same alignment constraints; it doesn't generate a truly relocatable binary (the effective addresses are fixed). But you don't have to specify the physical address at compile-time. This allows you to use the same kernel image for multiple AMP partitions.

Quoted 4 lines

For example, I want to boot from a non-zero address on the P1022DS. I should just be able to change "CONFIG_PHYSICAL_START" to, say, 0x08000000, and it should work, right? Any other bits that need to be done (i.e. U-Boot or device tree magic)?

Quoted 7 lines

You'll want the memory node adjusted for your restricted address range (I'm assuming that this is why you want to start at non-zero, and that you're not trying to have the kernel be located in the middle of its partition).

There are some special u-boot variables (bootm_low/bootm_size) that govern placement of the kernel, fdt, etc.

Thanks Scott. I should have looked in the u-boot docs. There are very clear instructions on how to setup an AMP environment in '.../doc/README.mpc8572ds' (http://git.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=blob;f=doc/README.mpc8572ds;h=06dab596bea52ab8d8c2ba89d86f793cc4881ccb;hb=HEAD).

Quoted 3 lines

-Scott

Signature · 2 lines
Meador Inge     | meador_inge AT mentor.com
Mentor Embedded | http://www.mentor.com/embedded-software