ARM: imx53_loco: add all pad configure.

PATCH RESEND New Richard Zhao 3 participants 7 messages Feb 18, 2011

Subsystems (3)

Arm (32-bit) Arm sub-architectures Arm i.MX and Layerscape

lore

Share & tools

lore

Richard Zhao

author

2011-02-18 04:36 UTC #0 lore raw

PATCH RESEND 1/4 ARM: imx53_loco: add all pad configure.

Signed-off-by Richard Zhao <[email protected]>

arch/arm/mach-mx5/board-mx53_loco.c +137 -0

index 0fea252..b8241bd 100644
@@ -39,8 +39,145 @@
 #define LOCO_FEC_PHY_RST		IMX_GPIO_NR(7, 6)
 
 static iomux_v3_cfg_t mx53_loco_pads[] = {
+	/* FEC */
+	MX53_PAD_FEC_MDC__FEC_MDC,
+	MX53_PAD_FEC_MDIO__FEC_MDIO,
+	MX53_PAD_FEC_REF_CLK__FEC_TX_CLK,
+	MX53_PAD_FEC_RX_ER__FEC_RX_ER,
+	MX53_PAD_FEC_CRS_DV__FEC_RX_DV,
+	MX53_PAD_FEC_RXD1__FEC_RDATA_1,
+	MX53_PAD_FEC_RXD0__FEC_RDATA_0,
+	MX53_PAD_FEC_TX_EN__FEC_TX_EN,
+	MX53_PAD_FEC_TXD1__FEC_TDATA_1,
+	MX53_PAD_FEC_TXD0__FEC_TDATA_0,
+	/* FEC_nRST */
+	MX53_PAD_PATA_DA_0__GPIO7_6,
+	/* FEC_nINT */
+	MX53_PAD_PATA_DATA4__GPIO2_4,
+	/* AUDMUX5 */
+	MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC,
+	MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD,
+	MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS,
+	MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD,
+	/* I2C2 */
+	MX53_PAD_KEY_COL3__I2C2_SCL,
+	MX53_PAD_KEY_ROW3__I2C2_SDA,
+	/* SD1 */
+	MX53_PAD_SD1_CMD__ESDHC1_CMD,
+	MX53_PAD_SD1_CLK__ESDHC1_CLK,
+	MX53_PAD_SD1_DATA0__ESDHC1_DAT0,
+	MX53_PAD_SD1_DATA1__ESDHC1_DAT1,
+	MX53_PAD_SD1_DATA2__ESDHC1_DAT2,
+	MX53_PAD_SD1_DATA3__ESDHC1_DAT3,
+	/* SD3 */
+	MX53_PAD_PATA_DATA8__ESDHC3_DAT0,
+	MX53_PAD_PATA_DATA9__ESDHC3_DAT1,
+	MX53_PAD_PATA_DATA10__ESDHC3_DAT2,
+	MX53_PAD_PATA_DATA11__ESDHC3_DAT3,
+	MX53_PAD_PATA_DATA0__ESDHC3_DAT4,
+	MX53_PAD_PATA_DATA1__ESDHC3_DAT5,
+	MX53_PAD_PATA_DATA2__ESDHC3_DAT6,
+	MX53_PAD_PATA_DATA3__ESDHC3_DAT7,
+	MX53_PAD_PATA_IORDY__ESDHC3_CLK,
+	MX53_PAD_PATA_RESET_B__ESDHC3_CMD,
+	/* SD3_CD */
+	MX53_PAD_EIM_DA11__GPIO3_11,
+	/* SD3_WP */
+	MX53_PAD_EIM_DA12__GPIO3_12,
+	/* VGA */
+	MX53_PAD_EIM_OE__IPU_DI1_PIN7,
+	MX53_PAD_EIM_RW__IPU_DI1_PIN8,
+	/* DISPLB */
+	MX53_PAD_EIM_D20__IPU_SER_DISP0_CS,
+	MX53_PAD_EIM_D21__IPU_DISPB0_SER_CLK,
+	MX53_PAD_EIM_D22__IPU_DISPB0_SER_DIN,
+	MX53_PAD_EIM_D23__IPU_DI0_D0_CS,
+	/* DISP0_POWER_EN */
+	MX53_PAD_EIM_D24__GPIO3_24,
+	/* DISP0 DET INT */
+	MX53_PAD_EIM_D31__GPIO3_31,
+	/* LVDS */
+	MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3,
+	MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK,
+	MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2,
+	MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1,
+	MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0,
+	MX53_PAD_LVDS1_TX3_P__LDB_LVDS1_TX3,
+	MX53_PAD_LVDS1_TX2_P__LDB_LVDS1_TX2,
+	MX53_PAD_LVDS1_CLK_P__LDB_LVDS1_CLK,
+	MX53_PAD_LVDS1_TX1_P__LDB_LVDS1_TX1,
+	MX53_PAD_LVDS1_TX0_P__LDB_LVDS1_TX0,
+	/* I2C1 */
+	MX53_PAD_CSI0_DAT8__I2C1_SDA,
+	MX53_PAD_CSI0_DAT9__I2C1_SCL,
+	/* UART1 */
 	MX53_PAD_CSI0_DAT10__UART1_TXD_MUX,
 	MX53_PAD_CSI0_DAT11__UART1_RXD_MUX,
+	/* CSI0 */
+	MX53_PAD_CSI0_DAT12__IPU_CSI0_D_12,
+	MX53_PAD_CSI0_DAT13__IPU_CSI0_D_13,
+	MX53_PAD_CSI0_DAT14__IPU_CSI0_D_14,
+	MX53_PAD_CSI0_DAT15__IPU_CSI0_D_15,
+	MX53_PAD_CSI0_DAT16__IPU_CSI0_D_16,
+	MX53_PAD_CSI0_DAT17__IPU_CSI0_D_17,
+	MX53_PAD_CSI0_DAT18__IPU_CSI0_D_18,
+	MX53_PAD_CSI0_DAT19__IPU_CSI0_D_19,
+	MX53_PAD_CSI0_VSYNC__IPU_CSI0_VSYNC,
+	MX53_PAD_CSI0_MCLK__IPU_CSI0_HSYNC,
+	MX53_PAD_CSI0_PIXCLK__IPU_CSI0_PIXCLK,
+	/* DISPLAY */
+	MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK,
+	MX53_PAD_DI0_PIN15__IPU_DI0_PIN15,
+	MX53_PAD_DI0_PIN2__IPU_DI0_PIN2,
+	MX53_PAD_DI0_PIN3__IPU_DI0_PIN3,
+	MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0,
+	MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1,
+	MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2,
+	MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3,
+	MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4,
+	MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5,
+	MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6,
+	MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7,
+	MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8,
+	MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9,
+	MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10,
+	MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11,
+	MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12,
+	MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13,
+	MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14,
+	MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15,
+	MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16,
+	MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17,
+	MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18,
+	MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19,
+	MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20,
+	MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21,
+	MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22,
+	MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23,
+	/* Audio CLK*/
+	MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK,
+	/* PWM */
+	MX53_PAD_GPIO_1__PWM2_PWMO,
+	/* SPDIF */
+	MX53_PAD_GPIO_7__SPDIF_PLOCK,
+	MX53_PAD_GPIO_17__SPDIF_OUT1,
+	/* GPIO */
+	MX53_PAD_PATA_DA_1__GPIO7_7,
+	MX53_PAD_PATA_DA_2__GPIO7_8,
+	MX53_PAD_PATA_DATA5__GPIO2_5,
+	MX53_PAD_PATA_DATA6__GPIO2_6,
+	MX53_PAD_PATA_DATA14__GPIO2_14,
+	MX53_PAD_PATA_DATA15__GPIO2_15,
+	MX53_PAD_PATA_INTRQ__GPIO7_2,
+	MX53_PAD_EIM_WAIT__GPIO5_0,
+	MX53_PAD_NANDF_WP_B__GPIO6_9,
+	MX53_PAD_NANDF_RB0__GPIO6_10,
+	MX53_PAD_NANDF_CS1__GPIO6_14,
+	MX53_PAD_NANDF_CS2__GPIO6_15,
+	MX53_PAD_NANDF_CS3__GPIO6_16,
+	MX53_PAD_GPIO_5__GPIO1_5,
+	MX53_PAD_GPIO_16__GPIO7_11,
+	MX53_PAD_GPIO_8__GPIO1_8,
 };
 
 static inline void mx53_loco_fec_reset(void)

Signature · 1 line

1.7.1

Richard Zhao

author

2011-02-18 04:36 UTC #1 lore raw

PATCH RESEND 2/4 ARM: imx53_loco add uncompress print

Signed-off-by Richard Zhao <[email protected]>

arch/arm/plat-mxc/include/mach/uncompress.h +1 -0

index e634d6c..b702884 100644
@@ -111,6 +111,7 @@ static __inline__ void __arch_decomp_setup(unsigned long arch_id)
 		uart_base = MX50_UART1_BASE_ADDR;
 		break;
 	case MACH_TYPE_MX53_EVK:
+	case MACH_TYPE_MX53_LOCO:
 		uart_base = MX53_UART1_BASE_ADDR;
 		break;
 	default:

Signature · 1 line

1.7.1

Richard Zhao

author

2011-02-18 04:36 UTC #2 lore raw

PATCH RESEND 3/4 ARM: imx53_loco: add i2c device support

In reply to Richard Zhao

Signed-off-by Richard Zhao <[email protected]>

arch/arm/mach-mx5/Kconfig +1 -0

index 10b6008..abea297 100644
@@ -146,6 +146,7 @@ config MACH_MX53_LOCO
 	bool "Support MX53 LOCO platforms"
 	select SOC_IMX53
 	select IMX_HAVE_PLATFORM_IMX_UART
+	select IMX_HAVE_PLATFORM_IMX_I2C
 	help
 	  Include support for MX53 LOCO platform. This includes specific
 	  configurations for the board and its peripherals.

arch/arm/mach-mx5/board-mx53_loco.c +6 -0

index b8241bd..ec9ea9c 100644
@@ -199,6 +199,10 @@ static struct fec_platform_data mx53_loco_fec_data = {
 	.phy = PHY_INTERFACE_MODE_RMII,
 };
 
+static const struct imxi2c_platform_data mx53_loco_i2c_data __initconst = {
+	.bitrate = 100000,
+};
+
 static void __init mx53_loco_board_init(void)
 {
 	mxc_iomux_v3_setup_multiple_pads(mx53_loco_pads,

@@ -206,6 +210,8 @@ static void __init mx53_loco_board_init(void)
 	imx53_add_imx_uart(0, NULL);
 	mx53_loco_fec_reset();
 	imx53_add_fec(&mx53_loco_fec_data);
+	imx53_add_imx_i2c(0, &mx53_loco_i2c_data);
+	imx53_add_imx_i2c(1, &mx53_loco_i2c_data);
 }
 
 static void __init mx53_loco_timer_init(void)

Signature · 1 line

1.7.1

Uwe Kleine-König

2011-02-18 08:45 UTC #3 lore raw

PATCH RESEND 3/4 ARM: imx53_loco: add i2c device support

arch/arm/mach-mx5/Kconfig config MACH_MX53_LOCO · line 149

Quoted 11 lines · Richard Zhao

Signed-off-by Richard Zhao <[email protected]>

arch/arm/mach-mx5/Kconfig +1 -0

index 10b6008..abea297 100644
@@ -146,6 +146,7 @@ config MACH_MX53_LOCO
 	bool "Support MX53 LOCO platforms"
 	select SOC_IMX53
 	select IMX_HAVE_PLATFORM_IMX_UART
+	select IMX_HAVE_PLATFORM_IMX_I2C

please keep these sorted alphabetically

Best regards
Uwe

Signature · 2 lines

Pengutronix e.K.                           | Uwe Kleine-K?nig            |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |

Richard Zhao

author

2011-02-18 08:59 UTC #4 lore raw

PATCH RESEND 3/4 ARM: imx53_loco: add i2c device support

Hi Uwe,

Quoted 13 lines · Uwe Kleine-K?nig

arch/arm/mach-mx5/Kconfig config MACH_MX53_LOCO · line 149
Quoted 11 lines · Richard Zhao
Signed-off-by Richard Zhao <[email protected]>
arch/arm/mach-mx5/Kconfig +1 -0
index 10b6008..abea297 100644
@@ -146,6 +146,7 @@ config MACH_MX53_LOCO
 	bool "Support MX53 LOCO platforms"
 	select SOC_IMX53
 	select IMX_HAVE_PLATFORM_IMX_UART
+	select IMX_HAVE_PLATFORM_IMX_I2C
please keep these sorted alphabetically

ok. I will move it up by one line.

Thanks
Richard

Quoted 13 lines

Best regards
Uwe

Signature · 7 lines

Pengutronix e.K.                           | Uwe Kleine-K?nig            |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Sascha Hauer

maintainer

2011-02-18 10:01 UTC #5 lore raw

PATCH RESEND 3/4 ARM: imx53_loco: add i2c device support

Quoted 16 lines · Richard Zhao

Hi Uwe,
Quoted 13 lines · Uwe Kleine-K?nig
arch/arm/mach-mx5/Kconfig config MACH_MX53_LOCO · line 149
Quoted 11 lines · Richard Zhao
Signed-off-by Richard Zhao <[email protected]>
arch/arm/mach-mx5/Kconfig +1 -0
index 10b6008..abea297 100644
@@ -146,6 +146,7 @@ config MACH_MX53_LOCO
 	bool "Support MX53 LOCO platforms"
 	select SOC_IMX53
 	select IMX_HAVE_PLATFORM_IMX_UART
+	select IMX_HAVE_PLATFORM_IMX_I2C
please keep these sorted alphabetically

Quoted 1 line

ok. I will move it up by one line.

Fixed while applying.

Sascha

Signature · 4 lines

Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

Richard Zhao

author

2011-02-18 04:36 UTC #6 lore raw

PATCH RESEND 4/4 ARM: imx50: correct iomux-mx50.h wrong daisy chain settings

In reply to Richard Zhao

Most fix is for uart txd/cts. They don't need to select input. And fix some other pads with wrong select input.

Signed-off-by Richard Zhao <[email protected]>

arch/arm/plat-mxc/include/mach/iomux-mx50.h +22 ~~-22~~

index 058a922..98e7fd0 100644
@@ -86,7 +86,7 @@
 #define MX50_PAD_I2C1_SCL__I2C1_SCL	IOMUX_PAD(0x2EC, 0x40, IOMUX_CONFIG_SION, 0x0, 0, \
 							MX50_I2C_PAD_CTRL)
 #define MX50_PAD_I2C1_SCL__GPIO_6_18	IOMUX_PAD(0x2EC, 0x40, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX50_PAD_I2C1_SCL__UART2_TXD	IOMUX_PAD(0x2EC, 0x40, 2, 0x7cc, 0, MX50_UART_PAD_CTRL)
+#define MX50_PAD_I2C1_SCL__UART2_TXD	IOMUX_PAD(0x2EC, 0x40, 2, 0x0, 0, MX50_UART_PAD_CTRL)
 
 #define MX50_PAD_I2C1_SDA__I2C1_SDA	IOMUX_PAD(0x2F0, 0x44, IOMUX_CONFIG_SION, 0x0, 0, \
 							MX50_I2C_PAD_CTRL)

@@ -96,7 +96,7 @@
 #define MX50_PAD_I2C2_SCL__I2C2_SCL	IOMUX_PAD(0x2F4, 0x48, IOMUX_CONFIG_SION, 0x0, 0, \
 							MX50_I2C_PAD_CTRL)
 #define MX50_PAD_I2C2_SCL__GPIO_6_20	IOMUX_PAD(0x2F4, 0x48, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX50_PAD_I2C2_SCL__UART2_CTS	IOMUX_PAD(0x2F4, 0x48, 2, 0x7c8, 0, MX50_UART_PAD_CTRL)
+#define MX50_PAD_I2C2_SCL__UART2_CTS	IOMUX_PAD(0x2F4, 0x48, 2, 0x0, 0, MX50_UART_PAD_CTRL)
 #define MX50_PAD_I2C2_SCL__DCDC_OK	IOMUX_PAD(0x2F4, 0x48, 7, 0x0, 0, NO_PAD_CTRL)
 
 #define MX50_PAD_I2C2_SDA__I2C2_SDA	IOMUX_PAD(0x2F8, 0x4C, IOMUX_CONFIG_SION, 0x0, 0, \

@@ -172,7 +172,7 @@
 
 #define MX50_PAD_SSI_RXFS__AUD3_RXFS	IOMUX_PAD(0x328, 0x7C, 0, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_SSI_RXFS__GPIO_6_4	IOMUX_PAD(0x328, 0x7C, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX50_PAD_SSI_RXFS__UART5_TXD	IOMUX_PAD(0x328, 0x7C, 2, 0x7e4, 0, MX50_UART_PAD_CTRL)
+#define MX50_PAD_SSI_RXFS__UART5_TXD	IOMUX_PAD(0x328, 0x7C, 2, 0x0, 0, MX50_UART_PAD_CTRL)
 #define MX50_PAD_SSI_RXFS__WEIM_D6	IOMUX_PAD(0x328, 0x7C, 3, 0x804, 0, NO_PAD_CTRL)
 #define MX50_PAD_SSI_RXFS__CSPI_SS2	IOMUX_PAD(0x328, 0x7C, 4, 0x6f0, 0, MX50_CSPI_SS_PAD)
 #define MX50_PAD_SSI_RXFS__FEC_COL	IOMUX_PAD(0x328, 0x7C, 5, 0x770, 0, PAD_CTL_DSE_HIGH)

@@ -186,25 +186,25 @@
 #define MX50_PAD_SSI_RXC__FEC_RX_CLK	IOMUX_PAD(0x32C, 0x80, 5, 0x780, 0, NO_PAD_CTRL)
 #define MX50_PAD_SSI_RXC__FEC_MDIO	IOMUX_PAD(0x32C, 0x80, 6, 0x774, 1, MX50_FEC_PAD_CTRL)
 
-#define MX50_PAD_UART1_TXD__UART1_TXD	IOMUX_PAD(0x330, 0x84, 0, 0x7c4, 0, MX50_UART_PAD_CTRL)
+#define MX50_PAD_UART1_TXD__UART1_TXD	IOMUX_PAD(0x330, 0x84, 0, 0x0, 0, MX50_UART_PAD_CTRL)
 #define MX50_PAD_UART1_TXD__GPIO_6_6	IOMUX_PAD(0x330, 0x84, 1, 0x0, 0, NO_PAD_CTRL)
 
 #define MX50_PAD_UART1_RXD__UART1_RXD	IOMUX_PAD(0x334, 0x88, 0, 0x7c4, 1, MX50_UART_PAD_CTRL)
 #define MX50_PAD_UART1_RXD__GPIO_6_7	IOMUX_PAD(0x334, 0x88, 1, 0x0, 0, NO_PAD_CTRL)
 
-#define MX50_PAD_UART1_CTS__UART1_CTS	IOMUX_PAD(0x338, 0x8C, 0, 0x7c0, 0, MX50_UART_PAD_CTRL)
+#define MX50_PAD_UART1_CTS__UART1_CTS	IOMUX_PAD(0x338, 0x8C, 0, 0x0, 0, MX50_UART_PAD_CTRL)
 #define MX50_PAD_UART1_CTS__GPIO_6_8	IOMUX_PAD(0x338, 0x8C, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX50_PAD_UART1_CTS__UART5_TXD	IOMUX_PAD(0x338, 0x8C, 2, 0x7e4, 2, MX50_UART_PAD_CTRL)
+#define MX50_PAD_UART1_CTS__UART5_TXD	IOMUX_PAD(0x338, 0x8C, 2, 0x0, 0, MX50_UART_PAD_CTRL)
 #define MX50_PAD_UART1_CTS__SD4_D4	IOMUX_PAD(0x338, 0x8C, 4, 0x760, 0, MX50_SD_PAD_CTRL)
 #define MX50_PAD_UART1_CTS__SD4_CMD	IOMUX_PAD(0x338, 0x8C, 5, 0x74c, 0, MX50_SD_PAD_CTRL)
 
 #define MX50_PAD_UART1_RTS__UART1_RTS	IOMUX_PAD(0x33C, 0x90, 0, 0x7c0, 1, MX50_UART_PAD_CTRL)
 #define MX50_PAD_UART1_RTS__GPIO_6_9	IOMUX_PAD(0x33C, 0x90, 1, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_UART1_RTS__UART5_RXD	IOMUX_PAD(0x33C, 0x90, 2, 0x7e4, 3, MX50_UART_PAD_CTRL)
-#define MX50_PAD_UART1_RTS__SD4_D5	IOMUX_PAD(0x33C, 0x90, 4, 0x0, 1, MX50_SD_PAD_CTRL)
-#define MX50_PAD_UART1_RTS__SD4_CLK	IOMUX_PAD(0x33C, 0x90, 5, 0x0, 1, MX50_SD_PAD_CTRL)
+#define MX50_PAD_UART1_RTS__SD4_D5	IOMUX_PAD(0x33C, 0x90, 4, 0x764, 0, MX50_SD_PAD_CTRL)
+#define MX50_PAD_UART1_RTS__SD4_CLK	IOMUX_PAD(0x33C, 0x90, 5, 0x748, 0, MX50_SD_PAD_CTRL)
 
-#define MX50_PAD_UART2_TXD__UART2_TXD	IOMUX_PAD(0x340, 0x94, 0, 0x7cc, 2, MX50_UART_PAD_CTRL)
+#define MX50_PAD_UART2_TXD__UART2_TXD	IOMUX_PAD(0x340, 0x94, 0, 0x0, 0, MX50_UART_PAD_CTRL)
 #define MX50_PAD_UART2_TXD__GPIO_6_10	IOMUX_PAD(0x340, 0x94, 1, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_UART2_TXD__SD4_D6	IOMUX_PAD(0x340, 0x94, 4, 0x768, 0, MX50_SD_PAD_CTRL)
 #define MX50_PAD_UART2_TXD__SD4_D4	IOMUX_PAD(0x340, 0x94, 5, 0x760, 1, MX50_SD_PAD_CTRL)

@@ -214,7 +214,7 @@
 #define MX50_PAD_UART2_RXD__SD4_D7	IOMUX_PAD(0x344, 0x98, 4, 0x76c, 0, MX50_SD_PAD_CTRL)
 #define MX50_PAD_UART2_RXD__SD4_D5	IOMUX_PAD(0x344, 0x98, 5, 0x764, 1, MX50_SD_PAD_CTRL)
 
-#define MX50_PAD_UART2_CTS__UART2_CTS	IOMUX_PAD(0x348, 0x9C, 0, 0x7c8, 2, MX50_UART_PAD_CTRL)
+#define MX50_PAD_UART2_CTS__UART2_CTS	IOMUX_PAD(0x348, 0x9C, 0, 0x0, 0, MX50_UART_PAD_CTRL)
 #define MX50_PAD_UART2_CTS__GPIO_6_12	IOMUX_PAD(0x348, 0x9C, 1, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_UART2_CTS__SD4_CMD	IOMUX_PAD(0x348, 0x9C, 4, 0x74c, 1, MX50_SD_PAD_CTRL)
 #define MX50_PAD_UART2_CTS__SD4_D6	IOMUX_PAD(0x348, 0x9C, 5, 0x768, 1, MX50_SD_PAD_CTRL)

@@ -224,7 +224,7 @@
 #define MX50_PAD_UART2_RTS__SD4_CLK	IOMUX_PAD(0x34C, 0xA0, 4, 0x748, 1, MX50_SD_PAD_CTRL)
 #define MX50_PAD_UART2_RTS__SD4_D7	IOMUX_PAD(0x34C, 0xA0, 5, 0x76c, 1, MX50_SD_PAD_CTRL)
 
-#define MX50_PAD_UART3_TXD__UART3_TXD	IOMUX_PAD(0x350, 0xA4, 0, 0x7d4, 0, MX50_UART_PAD_CTRL)
+#define MX50_PAD_UART3_TXD__UART3_TXD	IOMUX_PAD(0x350, 0xA4, 0, 0x0, 0, MX50_UART_PAD_CTRL)
 #define MX50_PAD_UART3_TXD__GPIO_6_14	IOMUX_PAD(0x350, 0xA4, 1, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_UART3_TXD__SD1_D4	IOMUX_PAD(0x350, 0xA4, 3, 0x0, 0, MX50_SD_PAD_CTRL)
 #define MX50_PAD_UART3_TXD__SD4_D0	IOMUX_PAD(0x350, 0xA4, 4, 0x750, 0, MX50_SD_PAD_CTRL)

@@ -238,9 +238,9 @@
 #define MX50_PAD_UART3_RXD__SD2_CD	IOMUX_PAD(0x354, 0xA8, 5, 0x740, 0, MX50_SD_PAD_CTRL)
 #define MX50_PAD_UART3_RXD__WEIM_D13	IOMUX_PAD(0x354, 0xA8, 6, 0x820, 0, NO_PAD_CTRL)
 
-#define MX50_PAD_UART4_TXD__UART4_TXD	IOMUX_PAD(0x358, 0xAC, 0, 0x7dc, 0, MX50_UART_PAD_CTRL)
+#define MX50_PAD_UART4_TXD__UART4_TXD	IOMUX_PAD(0x358, 0xAC, 0, 0x0, 0, MX50_UART_PAD_CTRL)
 #define MX50_PAD_UART4_TXD__GPIO_6_16	IOMUX_PAD(0x358, 0xAC, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX50_PAD_UART4_TXD__UART3_CTS	IOMUX_PAD(0x358, 0xAC, 2, 0x7d0, 0, MX50_UART_PAD_CTRL)
+#define MX50_PAD_UART4_TXD__UART3_CTS	IOMUX_PAD(0x358, 0xAC, 2, 0x0, 0, MX50_UART_PAD_CTRL)
 #define MX50_PAD_UART4_TXD__SD1_D6	IOMUX_PAD(0x358, 0xAC, 3, 0x0, 0, MX50_SD_PAD_CTRL)
 #define MX50_PAD_UART4_TXD__SD4_D2	IOMUX_PAD(0x358, 0xAC, 4, 0x758, 0, MX50_SD_PAD_CTRL)
 #define MX50_PAD_UART4_TXD__SD2_LCTL	IOMUX_PAD(0x358, 0xAC, 5, 0x0, 0, MX50_SD_PAD_CTRL)

@@ -278,7 +278,7 @@
 #define MX50_PAD_ECSPI1_MOSI__GPIO_4_13		IOMUX_PAD(0x374, 0xC8, 1, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_ECSPI1_MOSI__CSPI_SS1		IOMUX_PAD(0x374, 0xC8, 2, 0x6ec, 1, MX50_CSPI_SS_PAD)
 #define MX50_PAD_ECSPI1_MOSI__ECSPI2_SS1	IOMUX_PAD(0x374, 0xC8, 3, 0x0, 0, MX50_CSPI_SS_PAD)
-#define MX50_PAD_ECSPI1_MOSI__UART3_CTS		IOMUX_PAD(0x374, 0xC8, 4, 0x7d0, 3, MX50_UART_PAD_CTRL)
+#define MX50_PAD_ECSPI1_MOSI__UART3_CTS		IOMUX_PAD(0x374, 0xC8, 4, 0x0, 0, MX50_UART_PAD_CTRL)
 #define MX50_PAD_ECSPI1_MOSI__EPDC_SDCE7	IOMUX_PAD(0x374, 0xC8, 5, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_ECSPI1_MOSI__WEIM_D9		IOMUX_PAD(0x374, 0xC8, 7, 0x810, 0, NO_PAD_CTRL)

@@ -294,7 +294,7 @@
 #define MX50_PAD_ECSPI1_SS0__GPIO_4_15		IOMUX_PAD(0x37C, 0xD0, 1, 0x0, 0, PAD_CTL_PUS_100K_UP)
 #define MX50_PAD_ECSPI1_SS0__CSPI_SS3		IOMUX_PAD(0x37C, 0xD0, 2, 0x6f4, 1, MX50_CSPI_SS_PAD)
 #define MX50_PAD_ECSPI1_SS0__ECSPI2_SS3		IOMUX_PAD(0x37C, 0xD0, 3, 0x0, 0, MX50_CSPI_SS_PAD)
-#define MX50_PAD_ECSPI1_SS0__UART4_CTS		IOMUX_PAD(0x37C, 0xD0, 4, 0x7d8, 1, MX50_UART_PAD_CTRL)
+#define MX50_PAD_ECSPI1_SS0__UART4_CTS		IOMUX_PAD(0x37C, 0xD0, 4, 0x0, 0, MX50_UART_PAD_CTRL)
 #define MX50_PAD_ECSPI1_SS0__EPDC_SDCE9		IOMUX_PAD(0x37C, 0xD0, 5, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_ECSPI1_SS0__WEIM_D11		IOMUX_PAD(0x37C, 0xD0, 7, 0x818, 0, NO_PAD_CTRL)

@@ -311,17 +311,17 @@
 #define MX50_PAD_ECSPI2_MOSI__GPIO_4_17		IOMUX_PAD(0x384, 0xD8, 1, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_ECSPI2_MOSI__ELCDIF_RD		IOMUX_PAD(0x384, 0xD8, 2, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_ECSPI2_MOSI__ECSPI1_SS1	IOMUX_PAD(0x384, 0xD8, 3, 0x0, 0, MX50_CSPI_SS_PAD)
-#define MX50_PAD_ECSPI2_MOSI__UART5_CTS		IOMUX_PAD(0x384, 0xD8, 4, 0x7e0, 1, MX50_UART_PAD_CTRL)
+#define MX50_PAD_ECSPI2_MOSI__UART5_CTS		IOMUX_PAD(0x384, 0xD8, 4, 0x0, 0, MX50_UART_PAD_CTRL)
 #define MX50_PAD_ECSPI2_MOSI__ELCDIF_EN		IOMUX_PAD(0x384, 0xD8, 5, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_ECSPI2_MOSI__NANDF_CEN5	IOMUX_PAD(0x384, 0xD8, 6, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_ECSPI2_MOSI__WEIM_D9		IOMUX_PAD(0x384, 0xD8, 7, 0x810, 1, NO_PAD_CTRL)
 
-#define MX50_PAD_ECSPI2_MISO__ECSPI2_MISO	IOMUX_PAD(0x388, 0xDC, 0, 0x73c, 0, NO_PAD_CTRL)
+#define MX50_PAD_ECSPI2_MISO__ECSPI2_MISO	IOMUX_PAD(0x388, 0xDC, 0, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_ECSPI2_MISO__GPIO_4_18		IOMUX_PAD(0x388, 0xDC, 1, 0x0, 0, PAD_CTL_PUS_100K_UP)
 #define MX50_PAD_ECSPI2_MISO__ELCDIF_RS		IOMUX_PAD(0x388, 0xDC, 2, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_ECSPI2_MISO__ECSPI1_SS2	IOMUX_PAD(0x388, 0xDC, 3, 0x0, 0, MX50_CSPI_SS_PAD)
-#define MX50_PAD_ECSPI2_MISO__UART5_TXD		IOMUX_PAD(0x388, 0xDC, 4, 0x7e4, 4, MX50_UART_PAD_CTRL)
-#define MX50_PAD_ECSPI2_MISO__ELCDIF_VSYNC	IOMUX_PAD(0x388, 0xDC, 5, 0x0, 0, NO_PAD_CTRL)
+#define MX50_PAD_ECSPI2_MISO__UART5_TXD		IOMUX_PAD(0x388, 0xDC, 4, 0x0, 0, MX50_UART_PAD_CTRL)
+#define MX50_PAD_ECSPI2_MISO__ELCDIF_VSYNC	IOMUX_PAD(0x388, 0xDC, 5, 0x73c, 0, NO_PAD_CTRL)
 #define MX50_PAD_ECSPI2_MISO__NANDF_CEN6	IOMUX_PAD(0x388, 0xDC, 6, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_ECSPI2_MISO__WEIM_D10		IOMUX_PAD(0x388, 0xDC, 7, 0x814, 1, NO_PAD_CTRL)

@@ -503,7 +503,7 @@
 #define MX50_PAD_DISP_RD__ELCDIF_EN	IOMUX_PAD(0x430, 0x150, 2, 0x0, 0, MX50_ELCDIF_PAD_CTRL)
 #define MX50_PAD_DISP_RD__WEIM_A25	IOMUX_PAD(0x430, 0x150, 3, 0x0, 0, NO_PAD_CTRL)
 
-#define MX50_PAD_DISP_RS__ELCDIF_RS	IOMUX_PAD(0x434, 0x154, 0, 0x73c, 1, MX50_ELCDIF_PAD_CTRL)
+#define MX50_PAD_DISP_RS__ELCDIF_RS	IOMUX_PAD(0x434, 0x154, 0, 0x0, 0, MX50_ELCDIF_PAD_CTRL)
 #define MX50_PAD_DISP_RS__GPIO_2_17	IOMUX_PAD(0x434, 0x154, 1, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_DISP_RS__ELCDIF_VSYNC	IOMUX_PAD(0x434, 0x154, 2, 0x73c, 1, MX50_ELCDIF_PAD_CTRL)
 #define MX50_PAD_DISP_RS__WEIM_A26	IOMUX_PAD(0x434, 0x154, 3, 0x0, 0, NO_PAD_CTRL)

@@ -691,8 +691,8 @@
 
 #define MX50_PAD_EPDC_D9__EPDC_D9	IOMUX_PAD(0x570, 0x1D4, 0, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_EPDC_D9__GPIO_3_9	IOMUX_PAD(0x570, 0x1D4, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX50_PAD_EPDC_D9__WEIM_D9	IOMUX_PAD(0x570, 0x1D4, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX50_PAD_EPDC_D9__ELCDIF_D25	IOMUX_PAD(0x570, 0x1D4, 3, 0x810, 2, MX50_ELCDIF_PAD_CTRL)
+#define MX50_PAD_EPDC_D9__WEIM_D9	IOMUX_PAD(0x570, 0x1D4, 2, 0x810, 2, NO_PAD_CTRL)
+#define MX50_PAD_EPDC_D9__ELCDIF_D25	IOMUX_PAD(0x570, 0x1D4, 3, 0x0, 0, MX50_ELCDIF_PAD_CTRL)
 
 #define MX50_PAD_EPDC_D10__EPDC_D10	IOMUX_PAD(0x574, 0x1D8, 0, 0x0, 0, NO_PAD_CTRL)
 #define MX50_PAD_EPDC_D10__GPIO_3_10	IOMUX_PAD(0x574, 0x1D8, 1, 0x0, 0, NO_PAD_CTRL)

Signature · 1 line

1.7.1