MAX3107 driver faulty
Hello,
i want to use the MAX3107 driver,
thats included in the kernel 2.6.37.
I think the driver is faulty.
I have done several changes,
before the driver works rudimentary.
I have check the datasheet and found
inconsistence between chip and driver.
In AutoCTS AutoRTS Mode the Register
txdisable and rxdisable should be set.
But txdisable isnt set, so the max3107 sends
data even the cts signal is high.
The IntOscen Flag (enable internal Oscilator) is never set.
Different register write operations are done in one stream.
Example: http://lxr.free-electrons.com/ident?a=arm;i=max3107_register_init
But in the datasheet it is explained:
"If the SPI burst address is different to 0x00, the MAX3107 automatically increments the register address after each SPI data byte."
So it is impossible to write in the register 0x1D, 0x1C, 0x1B in one stream.
after the first address 0x1D the maxim increment the address automatically to 0x1E.
Have somebody test the driver,
or have although trouble with the chip?
Because i am really new with the kernel hacking,
what are the next steps, build an patch?
thanks a lot
Quoted 31 lines · Nico Becker
Hello,
i want to use the MAX3107 driver,
thats included in the kernel 2.6.37.I think the driver is faulty.
I have done several changes,
before the driver works rudimentary.I have check the datasheet and found
inconsistence between chip and driver.In AutoCTS AutoRTS Mode the Register
txdisable and rxdisable should be set.
But txdisable isnt set, so the max3107 sends
data even the cts signal is high.The IntOscen Flag (enable internal Oscilator) is never set.
Different register write operations are done in one stream.
Example: http://lxr.free-electrons.com/ident?a=arm;i=max3107_register_init
But in the datasheet it is explained:
"If the SPI burst address is different to0x00, the MAX3107 automatically increments the register address after each SPI data byte."
So it is impossible to write in the register0x1D,0x1C,0x1Bin one stream.
after the first address0x1Dthe maxim increment the address automatically to0x1E.
Quoted 2 lines
Have somebody test the driver,
or have although trouble with the chip?
I haven't, but I'll add the people who brought the driver to the kernel to CC. Maybe they can comment.
Quoted 2 lines
Because i am really new with the kernel hacking,
what are the next steps, build an patch?
Doing patches (one per issue) might be an idea. It is usually easier to talk about code. Reading Documentation/SubmittingPatches will probably make the process easier.
Thanks,
Wolfram
Signature · 2 lines
Pengutronix e.K. | Wolfram Sang | Industrial Linux Solutions | http://www.pengutronix.de/ |
Quoted 5 lines
Quoted 2 lines
Have somebody test the driver,
or have although trouble with the chip?I haven't, but I'll add the people who brought the driver to the kernel to CC. Maybe they can comment.
It had some testing but in a limited configuration and mostly for a device that then got canned. Thus I can well believe the autocts/rts isn't set right, and IntOscen may well only get set if the firmware happens to do it etc
Quoted 6 lines
Quoted 2 lines
Because i am really new with the kernel hacking,
what are the next steps, build an patch?Doing patches (one per issue) might be an idea. It is usually easier to talk about code. Reading
Documentation/SubmittingPatcheswill probably make the process easier.
I would probably send it as four patches
1. A patch for the IntOscen configuration
2. A patch to fix autocts/rts
3. A patch to fix the register updates
4. A patch to add any platform specific stuff you need for your device.
Thanks
Alan