Add Board Support for Siemens L0 Board
PATCH 1/1 Add Board Support for Siemens L0 Board
Add Board Support for Siemens L0 Board
Siemens L0 is a ARM9 AT91 SAM9263 SoC based board with NAND Flash.
arch/arm/mach-at91/Kconfig +6 -0
@@ -306,6 +306,12 @@ Select this if you are using Atmel's AT91SAM9263-EK Evaluation Kit. <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4057> +config MACH_SIEMENS_L0 + bool "Siemens L0" + select HAVE_NAND_ATMEL_BUSWIDTH_16 + help + Select this if you are using the Siemens L0 board. + config MACH_USB_A9263 bool "CALAO USB-A9263" help
arch/arm/mach-at91/Makefile +1 -0
@@ -54,6 +54,7 @@ # AT91SAM9263 board-specific support obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o +obj-$(CONFIG_MACH_SIEMENS_L0) += board-siemens-l0.o obj-$(CONFIG_MACH_USB_A9263) += board-usb-a9263.o obj-$(CONFIG_MACH_NEOCORE926) += board-neocore926.o
arch/arm/mach-at91/board-siemens-l0.c new file +189 -0
189 lines not on this page · raw message
PATCH 1/1 Add Board Support for Siemens L0 Board
Quoted 5 lines · Manuel Traut
Add Board Support for Siemens L0 Board
Siemens L0 is a ARM9 AT91 SAM9263 SoC based board with NAND Flash.
Signed-off-by Manuel Traut <[email protected]>
can you rebase on my as patch that merge all 9263 defconfig
and can we also merge this board with an other one? such as the 9263ek?
Best Regards,
J.
PATCH 1/1 Add Board Support for Siemens L0 Board
In reply to Manuel TrautQuoted 11 lines · Manuel Traut
Add Board Support for Siemens L0 Board
Siemens L0 is a ARM9 AT91 SAM9263 SoC based board with NAND Flash.
Signed-off-by Manuel Traut <[email protected]>Index: linux-2.6.39-rc1/arch/arm/mach-at91/Kconfig
===================================================================
arch/arm/mach-at91/Kconfig line 311
Quoted 6 lines
arch/arm/mach-at91/Kconfig +3
-0@@ -306,6 +306,12 @@ Select this if you are using Atmel's AT91SAM9263-EK Evaluation Kit. <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4057> +config MACH_SIEMENS_L0 + bool "Siemens L0" + select HAVE_NAND_ATMEL_BUSWIDTH_16
hmm, isn't that a stopper for a multi-machine kernel? I havn't checked deeply, but the only thing HAVE_NAND_ATMEL_BUSWIDTH_16 does is allowing to select CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16. When looking at arch/arm/mach-at91/board-at572d940hf_ek.c the latter looks like something that should be possible to be different per board. (Obviously that's not a comment that should stop your patch getting in, but (maybe) a for the at91 maintainers to solve.)
Quoted 34 lines
arch/arm/mach-at91/Kconfig +3
-0+ help + Select this if you are using the Siemens L0 board. + config MACH_USB_A9263 bool "CALAO USB-A9263" helpIndex: linux-2.6.39-rc1/arch/arm/mach-at91/Makefile
===================================================================arch/arm/mach-at91/Makefile +1
-0@@ -54,6 +54,7 @@ # AT91SAM9263 board-specific support obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o +obj-$(CONFIG_MACH_SIEMENS_L0) += board-siemens-l0.o obj-$(CONFIG_MACH_USB_A9263) += board-usb-a9263.o obj-$(CONFIG_MACH_NEOCORE926) += board-neocore926.oIndex:
linux-2.6.39-rc1/arch/arm/mach-at91/board-siemens-l0.c
===================================================================arch/arm/mach-at91/board-siemens-l0.c new file +11
-0@@ -0,0 +1,189 @@ +/* +* linux/arch/arm/mach-at91/board-siemens-l0.c +* based on linux/arch/arm/mach-at91/board-sam9263ek.c +* +* Copyright (C) 2005 SAN People +* Copyright (C) 2007 Atmel Corporation. +* Copyright (C) 2011 Linutronix GmbH +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or
arch/arm/mach-at91/board-siemens-l0.c line 21
Quoted 10 lines
arch/arm/mach-at91/board-siemens-l0.c new file +10
-0+* (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
This address isn't valid any more. I suggest to just skip the whole paragraph as this should be already handled good enough by the toplevel copyright file.
Quoted 153 lines
arch/arm/mach-at91/board-siemens-l0.c new file +153
-0+*/ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/mm.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/mtd/physmap.h> +#include <linux/gpio_keys.h> + +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/irq.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <mach/hardware.h> +#include <mach/board.h> +#include <mach/gpio.h> +#include <mach/at91sam9_smc.h> +#include <mach/at91_shdwc.h> + +#include "sam9_smc.h" +#include "generic.h" + +static void __init l0_map_io (void ) +{ +/* Initialize processor: 16.000 MHz crystal */ +at91sam9263_initialize (16000000 ); + +/* DBGU on ttyS0. (Rx & Tx only) */ +at91_register_uart (0 ,0 ,0 ); + +/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */ +at91_register_uart (AT91SAM9263_ID_US0 ,1 , +ATMEL_UART_CTS |ATMEL_UART_RTS ); + +/* set serial console to ttyS0 (ie, DBGU) */ +at91_set_serial_console (0 ); +} + +static void __init l0_init_irq (void ) +{ +at91sam9263_init_interrupts (NULL ); +} + +/* +* USB Host port +*/ +static struct at91_usbh_data __initdata l0_usbh_data = { + .ports =2 , + .vbus_pin = {AT91_PIN_PE2 ,AT91_PIN_PE5 }, +}; + +/* +* USB Device port +*/ +static struct at91_udc_data __initdata l0_udc_data = { + .vbus_pin =AT91_PIN_PE1 , + .pullup_pin =0 ,/* pull-up driven by UDC */ +}; + +/* +* MCI (SD/MMC) +*/ +static struct at91_mmc_data __initdata l0_mmc_data = { + .slot_b =0 , + .wire4 =1 , + .det_pin =AT91_PIN_PA16 , + .wp_pin =AT91_PIN_PE0 , +/* .vcc_pin = ... not connected */ +}; + +/* +* MACB Ethernet device +*/ +static struct at91_eth_data __initdata l0_macb_data = { + .phy_irq_pin =AT91_PIN_PE31 , + .is_rmii =1 , +}; + +/* +* CAN +*/ +static void sam9263l0_transceiver_switch (int on) +{ +if (on) { +at91_set_gpio_output (AT91_PIN_PA18 ,1 );/* CANRXEN */ +at91_set_gpio_output (AT91_PIN_PA19 ,0 );/* CANRS */ + }else { +at91_set_gpio_output (AT91_PIN_PA18 ,0 );/* CANRXEN */ +at91_set_gpio_output (AT91_PIN_PA19 ,1 );/* CANRS */ + } +} + +static struct at91_can_data l0_can_data = { + .transceiver_switch = sam9263l0_transceiver_switch, +}; + +/* +* Nand flash +*/ +static struct mtd_partition __initdata l0_nand_partition[] = { + { + .name ="bootloader" , + .offset =0 , + .size =SZ_256K , + }, + { + .name ="ubi" , + .offset =MTDPART_OFS_NXTBLK , + .size =MTDPART_SIZ_FULL , + }, +}; + +static struct mtd_partition *__init nand_partitions (int size, +int *num_partitions) +{ + *num_partitions =ARRAY_SIZE (l0_nand_partition); +return l0_nand_partition; +} + +static struct atmel_nand_data __initdata l0_nand_data = { + .ale =21 , + .cle =22 , +/* .det_pin = ... not connected */ + .rdy_pin =AT91_PIN_PA22 , + .enable_pin =AT91_PIN_PD15 , + .partition_info = nand_partitions, + .bus_width_16 =1 , +}; + +static void __init l0_add_device_nand (void ) +{ +at91_add_device_nand (&l0_nand_data); +} + +/* +* Init Board +*/ +static void __init l0_board_init (void ) +{ +/* Serial */ +at91_add_device_serial (); +/* USB Host */ +at91_add_device_usbh (&l0_usbh_data); +/* USB Device */ +at91_add_device_udc (&l0_udc_data); +/* MMC */ +at91_add_device_mmc (1 , &l0_mmc_data); +/* Ethernet */
arch/arm/mach-at91/board-siemens-l0.c line 184
Quoted 10 lines
arch/arm/mach-at91/board-siemens-l0.c new file +10
-0+at91_add_device_eth (&l0_macb_data); +/* NAND */ +l0_add_device_nand (); +/* CAN */ +at91_add_device_can (&l0_can_data); +} + +MACHINE_START (SIEMENS_L0 ,"Siemens L0" ) +/* Maintainer: Atmel */ + .boot_params = AT91_SDRAM_BASE + 0x100,
Do you really need this? With a recent bootloader it's not necessary.
arch/arm/mach-at91/board-siemens-l0.c line 188
Quoted 4 lines
arch/arm/mach-at91/board-siemens-l0.c new file +4
-0+ .timer = &at91sam926x_timer, + .map_io = l0_map_io, + .init_irq = l0_init_irq, + .init_machine = l0_board_init,
Regarding http://article.gmane.org/gmane.linux.ports.arm.omap/50721
this isn't in the right order.
Best regards
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-K?nig | Industrial Linux Solutions | http://www.pengutronix.de/ |