xilinx_ppc_boards: Change address of RESET_VECTOR
PATCH 1/1 xilinx_ppc_boards: Change address of RESET_VECTOR
Old address of RESET_VECTOR were overwritten by the bss sector, making impossible its run from xmd.
--- boards.cfg | 10 +++++----- 1 files changed, 5 insertions(+), 5 deletions(-)
boards.cfg +5 -5
@@ -675,9 +675,9 @@ yellowstone powerpc ppc4xx yosemite amcc yosemite powerpc ppc4xx yosemite amcc - yosemite:YOSEMITE yucca powerpc ppc4xx - amcc AP1000 powerpc ppc4xx ap1000 amirix -fx12mm powerpc ppc4xx fx12mm avnet - fx12mm:SYS_TEXT_BASE=0x04000000,RESET_VECTOR_ADDRESS=0x03FFFFFC,INIT_TLB=board/xilinx/ppc405-generic/init.o +fx12mm powerpc ppc4xx fx12mm avnet - fx12mm:SYS_TEXT_BASE=0x04000000,RESET_VECTOR_ADDRESS=0x04100000,INIT_TLB=board/xilinx/ppc405-generic/init.o fx12mm_flash powerpc ppc4xx fx12mm avnet - fx12mm:SYS_TEXT_BASE=0xF7F60000,RESET_VECTOR_ADDRESS=0xF7FFFFFC,INIT_TLB=board/xilinx/ppc405-generic/init.o -v5fx30teval powerpc ppc4xx v5fx30teval avnet - v5fx30teval:SYS_TEXT_BASE=0x04000000,RESET_VECTOR_ADDRESS=0x03FFFFFC,BOOT_FROM_XMD=1,INIT_TLB=board/xilinx/ppc440-generic/init.o +v5fx30teval powerpc ppc4xx v5fx30teval avnet - v5fx30teval:SYS_TEXT_BASE=0x04000000,RESET_VECTOR_ADDRESS=0x04100000,BOOT_FROM_XMD=1,INIT_TLB=board/xilinx/ppc440-generic/init.o v5fx30teval_flash powerpc ppc4xx v5fx30teval avnet - v5fx30teval:SYS_TEXT_BASE=0xF7F60000,RESET_VECTOR_ADDRESS=0xF7FFFFFC,INIT_TLB=board/xilinx/ppc440-generic/init.o CRAYL1 powerpc ppc4xx L1 cray CATcenter powerpc ppc4xx PPChameleonEVB dave - CATcenter:PPCHAMELEON_MODULE_MODEL=1
@@ -736,11 +736,11 @@ p3p440 powerpc ppc4xx - prodriv KAREF powerpc ppc4xx karef sandburst METROBOX powerpc ppc4xx metrobox sandburst xpedite1000 powerpc ppc4xx - xes -ml507 powerpc ppc4xx ml507 xilinx - ml507:SYS_TEXT_BASE=0x04000000,RESET_VECTOR_ADDRESS=0x03FFFFFC,BOOT_FROM_XMD=1,INIT_TLB=board/xilinx/ppc440-generic/init.o +ml507 powerpc ppc4xx ml507 xilinx - ml507:SYS_TEXT_BASE=0x04000000,RESET_VECTOR_ADDRESS=0x04100000,BOOT_FROM_XMD=1,INIT_TLB=board/xilinx/ppc440-generic/init.o ml507_flash powerpc ppc4xx ml507 xilinx - ml507:SYS_TEXT_BASE=0xF7F60000,RESET_VECTOR_ADDRESS=0xF7FFFFFC,INIT_TLB=board/xilinx/ppc440-generic/init.o -xilinx-ppc405-generic powerpc ppc4xx ppc405-generic xilinx - xilinx-ppc405-generic:SYS_TEXT_BASE=0x04000000,RESET_VECTOR_ADDRESS=0x03FFFFFC +xilinx-ppc405-generic powerpc ppc4xx ppc405-generic xilinx - xilinx-ppc405-generic:SYS_TEXT_BASE=0x04000000,RESET_VECTOR_ADDRESS=0x04100000 xilinx-ppc405-generic_flash powerpc ppc4xx ppc405-generic xilinx - xilinx-ppc405-generic:SYS_TEXT_BASE=0xF7F60000,RESET_VECTOR_ADDRESS=0xF7FFFFFC -xilinx-ppc440-generic powerpc ppc4xx ppc440-generic xilinx - xilinx-ppc440-generic:SYS_TEXT_BASE=0x04000000,RESET_VECTOR_ADDRESS=0x03FFFFFC,BOOT_FROM_XMD=1 +xilinx-ppc440-generic powerpc ppc4xx ppc440-generic xilinx - xilinx-ppc440-generic:SYS_TEXT_BASE=0x04000000,RESET_VECTOR_ADDRESS=0x04100000,BOOT_FROM_XMD=1 xilinx-ppc440-generic_flash powerpc ppc4xx ppc440-generic xilinx - xilinx-ppc440-generic:SYS_TEXT_BASE=0xF7F60000,RESET_VECTOR_ADDRESS=0xF7FFFFFC rsk7203 sh sh2 rsk7203 renesas - mpr2 sh sh3 mpr2 - -
Signature · 1 line
1.7.2.3
PATCH 1/1 xilinx_ppc_boards: Change address of RESET_VECTOR
Dear Ricardo Ribalda Delgado,
Quoted 4 lines · In message <[email protected]> you…
Old address of
RESET_VECTORwere overwritten by the bss sector, making impossible its run from xmd.Signed-off-by Ricardo Ribalda Delgado <[email protected]>
I would like to minimize the configuration information present in boards.cfg; the current state resulted just from the attempt to minimize changes when converting to from Makefile to boards.cfg, but that should not be the final state.
When you touch all of this anyway (and re-test it, obviously), can you then please take the chance and move all tis stuff from boards.cfg into your respective board config files, where it aktucally belongs?
Thanks.
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de The best things in life are for a fee.
PATCH 1/1 xilinx_ppc_boards: Change address of RESET_VECTOR
In reply to Ricardo Ribalda DelgadoQuoted 2 lines · On Wednesday 12 January 2011 10:14:42 Ricardo Ribalda Delgado wrote:
Old address of
RESET_VECTORwere overwritten by the bss sector, making impossible its run from xmd.
Applied to u-boot-ppc4xx/master. Thanks.
Cheers,
Stefan
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de