2.6.38.3 and 2.6.39-rc4 hangs after "Booting the kernel" on quad Pentium Pro system

DISCUSSION Chris Samuel 8 participants 40 messages Apr 22, 2011 – May 30, 2011 3 messages not in the archive x86

Share & tools

Chris Samuel

author

2011-04-22 13:39 UTC #0 lore raw

/* Please CC me in any response, I'm not on LKML or the x86 list */

Hi all, I'm afraid "perl scripts/get_maintainer.pl -f arch/x86/boot/compressed/misc.c" has pointed to you as the people to report this to.. ;-)

I've got an ancient Olivetti Netstrada, a deskside server system with quad Pentium Pro 200MHz processors, 256MB RAM, dual power supplies and five 4GB SCSI drives. I've been trying to get a newer distro on for a little while and you can read the backstory elsewhere [1].

Current problem is that I am unable to get either 2.6.38.3 or 2.6.39-rc4 (or the Debian Squeeze 686 and 486 2.6.32 based kernels) to boot, the final message I see is:

Booting the kernel.

The 2.6.18 based kernel from Debian Etch works with no problems, but the Lenny 2.6.26 based kernel panics when decompressing the initramfs claiming it's out of memory.

So far I've tried with a combination of 2.6.38.3 and 2.6.39-rc4:

1) A config based upon Debian's 2.6.32 kernel
2) A minimal config starting from an "allnoconfig" base.
3) An "allnoconfig" with the processor set to Pentium Pro and with all the "panic on hang" type checks turned on and the "panic=30" boot option.
4) An "allnoconfig" with verbose debug and boot messages and the processor set to i386.

All result in the same behaviour and I'm somewhat at a loss as to how to debug this further, being a sysadmin rather than a real kernel hacker. :-(

I've attached the 2.6.39-rc4 kernel config from point 4, and the kernel config for the working Debian kernel (2.6.18-6-686).

I've also attached the contents of /proc/cpuinfo, /proc/io*, /proc/scsi/scsi, /proc/modules and the output of lspci -vvv and of dmesg from Debian Sarge running the Debian Etch kernel (2.6.18-6-686).

This box has given me good service over the past 8 years or so and I'd hate to have to retire it now due to this when I feel Linux should still work on it..

Any ideas please ?

All the best,
Chris

[1] - http://www.csamuel.org/2011/04/22/modern-kernels-fail-to-boot-on-old-quad-processor-pentium-pro-server

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

#
# Automatically generated make config: don't edit
# Linux/i386 2.6.39-rc4 Kernel Configuration
# Fri Apr 22 12:13:20 2011
#
# CONFIG_64BIT is not set
CONFIG_X86_32=y
# CONFIG_X86_64 is not set
CONFIG_X86=y
CONFIG_INSTRUCTION_DECODER=y CONFIG_OUTPUT_FORMAT="elf32-i386" CONFIG_ARCH_DEFCONFIG="arch/x86/configs/i386_defconfig" CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_CLOCKSOURCE_WATCHDOG=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
# CONFIG_NEED_DMA_MAP_STATE is not set CONFIG_NEED_SG_DMA_LENGTH=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_HWEIGHT=y CONFIG_ARCH_MAY_HAVE_PC_FDC=y CONFIG_RWSEM_GENERIC_SPINLOCK=y
# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y CONFIG_GENERIC_CALIBRATE_DELAY=y
# CONFIG_GENERIC_TIME_VSYSCALL is not set CONFIG_ARCH_HAS_CPU_RELAX=y CONFIG_ARCH_HAS_DEFAULT_IDLE=y CONFIG_ARCH_HAS_CACHE_LINE_SIZE=y CONFIG_HAVE_SETUP_PER_CPU_AREA=y CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK=y CONFIG_NEED_PER_CPU_PAGE_FIRST_CHUNK=y
# CONFIG_HAVE_CPUMASK_OF_CPU_MAP is not set CONFIG_ARCH_HIBERNATION_POSSIBLE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y
# CONFIG_ZONE_DMA32 is not set CONFIG_ARCH_POPULATES_NODE_MAP=y
# CONFIG_AUDIT_ARCH is not set CONFIG_ARCH_SUPPORTS_OPTIMIZED_INLINING=y CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_X86_32_LAZY_GS=y CONFIG_ARCH_HWEIGHT_CFLAGS="-fcall-saved-ecx -fcall-saved-edx" CONFIG_KTIME_SCALAR=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" CONFIG_CONSTRUCTORS=y
CONFIG_HAVE_IRQ_WORK=y
CONFIG_IRQ_WORK=y

#
# General setup
#
# CONFIG_EXPERIMENTAL is not set
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_CROSS_COMPILE=""
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_HAVE_KERNEL_GZIP=y
CONFIG_HAVE_KERNEL_BZIP2=y
CONFIG_HAVE_KERNEL_LZMA=y
CONFIG_HAVE_KERNEL_XZ=y
CONFIG_HAVE_KERNEL_LZO=y
CONFIG_KERNEL_GZIP=y
# CONFIG_KERNEL_BZIP2 is not set
# CONFIG_KERNEL_LZMA is not set
# CONFIG_KERNEL_XZ is not set
# CONFIG_KERNEL_LZO is not set
# CONFIG_SWAP is not set
# CONFIG_SYSVIPC is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_FHANDLE is not set
CONFIG_HAVE_GENERIC_HARDIRQS=y

#
# IRQ subsystem
#
CONFIG_GENERIC_HARDIRQS=y
CONFIG_HAVE_SPARSE_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_IRQ_FORCED_THREADING=y
# CONFIG_SPARSE_IRQ is not set

#
# RCU Subsystem
#
CONFIG_TINY_RCU=y
# CONFIG_PREEMPT_RCU is not set
# CONFIG_RCU_TRACE is not set
# CONFIG_TREE_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=17
CONFIG_HAVE_UNSTABLE_SCHED_CLOCK=y
# CONFIG_CGROUPS is not set
CONFIG_NAMESPACES=y
# CONFIG_UTS_NS is not set
# CONFIG_PID_NS is not set
# CONFIG_SCHED_AUTOGROUP is not set
# CONFIG_SYSFS_DEPRECATED is not set
# CONFIG_RELAY is not set
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
# CONFIG_EXPERT is not set
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_PCSPKR_PLATFORM=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
CONFIG_HAVE_PERF_EVENTS=y

#
# Kernel Performance Events And Counters
#
CONFIG_PERF_EVENTS=y
# CONFIG_PERF_COUNTERS is not set
# CONFIG_DEBUG_PERF_USE_VMALLOC is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLUB_DEBUG=y
# CONFIG_COMPAT_BRK is not set
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_PROFILING is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_JUMP_LABEL is not set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_OPTPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_DMA_ATTRS=y
CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
CONFIG_HAVE_DMA_API_DEBUG=y
CONFIG_HAVE_HW_BREAKPOINT=y
CONFIG_HAVE_MIXED_BREAKPOINTS_REGS=y
CONFIG_HAVE_USER_RETURN_NOTIFIER=y
CONFIG_HAVE_PERF_EVENTS_NMI=y
CONFIG_HAVE_ARCH_JUMP_LABEL=y

#
# GCOV-based kernel profiling
#
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
# CONFIG_MODULES is not set
CONFIG_BLOCK=y
# CONFIG_LBDAF is not set
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set CONFIG_DEFAULT_NOOP=y CONFIG_DEFAULT_IOSCHED="noop"
# CONFIG_INLINE_SPIN_TRYLOCK is not set
# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set # CONFIG_INLINE_SPIN_LOCK is not set
# CONFIG_INLINE_SPIN_LOCK_BH is not set
# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set CONFIG_INLINE_SPIN_UNLOCK=y
# CONFIG_INLINE_SPIN_UNLOCK_BH is not set CONFIG_INLINE_SPIN_UNLOCK_IRQ=y
# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set # CONFIG_INLINE_READ_TRYLOCK is not set
# CONFIG_INLINE_READ_LOCK is not set
# CONFIG_INLINE_READ_LOCK_BH is not set
# CONFIG_INLINE_READ_LOCK_IRQ is not set
# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set CONFIG_INLINE_READ_UNLOCK=y
# CONFIG_INLINE_READ_UNLOCK_BH is not set CONFIG_INLINE_READ_UNLOCK_IRQ=y
# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set # CONFIG_INLINE_WRITE_TRYLOCK is not set
# CONFIG_INLINE_WRITE_LOCK is not set
# CONFIG_INLINE_WRITE_LOCK_BH is not set
# CONFIG_INLINE_WRITE_LOCK_IRQ is not set # CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set CONFIG_INLINE_WRITE_UNLOCK=y
# CONFIG_INLINE_WRITE_UNLOCK_BH is not set CONFIG_INLINE_WRITE_UNLOCK_IRQ=y
# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set # CONFIG_MUTEX_SPIN_ON_OWNER is not set
# CONFIG_FREEZER is not set

#
# Processor type and features
#
# CONFIG_NO_HZ is not set
# CONFIG_HIGH_RES_TIMERS is not set
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
# CONFIG_SMP is not set
# CONFIG_X86_EXTENDED_PLATFORM is not set
# CONFIG_X86_32_IRIS is not set
# CONFIG_SCHED_OMIT_FRAME_POINTER is not set
# CONFIG_PARAVIRT_GUEST is not set
CONFIG_NO_BOOTMEM=y
# CONFIG_MEMTEST is not set
CONFIG_M386=y
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MGEODE_LX is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_MVIAC7 is not set
# CONFIG_MCORE2 is not set
# CONFIG_MATOM is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_INTERNODE_CACHE_SHIFT=4
# CONFIG_X86_CMPXCHG is not set
# CONFIG_CMPXCHG_LOCAL is not set
CONFIG_X86_L1_CACHE_SHIFT=4
# CONFIG_X86_PPRO_FENCE is not set
CONFIG_X86_F00F_BUG=y
CONFIG_X86_INVD_BUG=y
CONFIG_X86_MINIMUM_CPU_FAMILY=3
CONFIG_CPU_SUP_INTEL=y
CONFIG_CPU_SUP_CYRIX_32=y
CONFIG_CPU_SUP_AMD=y
CONFIG_CPU_SUP_CENTAUR=y
CONFIG_CPU_SUP_TRANSMETA_32=y
CONFIG_CPU_SUP_UMC_32=y
# CONFIG_HPET_TIMER is not set
CONFIG_DMI=y
# CONFIG_IOMMU_HELPER is not set
# CONFIG_IOMMU_API is not set
CONFIG_NR_CPUS=1
# CONFIG_IRQ_TIME_ACCOUNTING is not set
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
# CONFIG_X86_UP_APIC is not set
# CONFIG_X86_MCE is not set
CONFIG_VM86=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_X86_REBOOTFIXUPS is not set
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
# CONFIG_X86_CPUID is not set
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_HIGHMEM=y
# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
# CONFIG_ARCH_DMA_ADDR_T_64BIT is not set
CONFIG_ILLEGAL_POINTER_VALUE=0
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_HAVE_MEMBLOCK=y
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_COMPACTION is not set
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_VIRT_TO_BUS=y
# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
# CONFIG_TRANSPARENT_HUGEPAGE is not set
CONFIG_NEED_PER_CPU_KM=y
# CONFIG_HIGHPTE is not set
# CONFIG_X86_CHECK_BIOS_CORRUPTION is not set
CONFIG_X86_RESERVE_LOW=64
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_MTRR_SANITIZER is not set
CONFIG_X86_PAT=y
CONFIG_ARCH_USES_PG_UNCACHED=y
# CONFIG_SECCOMP is not set
# CONFIG_CC_STACKPROTECTOR is not set
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
# CONFIG_SCHED_HRTICK is not set
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_PHYSICAL_START=0x1000000
# CONFIG_RELOCATABLE is not set
CONFIG_PHYSICAL_ALIGN=0x1000000
# CONFIG_COMPAT_VDSO is not set
# CONFIG_CMDLINE_BOOL is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y

#
# Power management and ACPI options
#
# CONFIG_SUSPEND is not set
# CONFIG_PM_RUNTIME is not set
# CONFIG_SFI is not set

#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set
# CONFIG_CPU_IDLE is not set

#
# Bus options (PCI etc.)
#
# CONFIG_PCI is not set
# CONFIG_ARCH_SUPPORTS_MSI is not set
CONFIG_ISA_DMA_API=y
# CONFIG_ISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
# CONFIG_OLPC is not set
# CONFIG_PCCARD is not set

#
# Executable file formats / Emulations
#
# CONFIG_BINFMT_ELF is not set
CONFIG_HAVE_AOUT=y
# CONFIG_BINFMT_AOUT is not set
# CONFIG_BINFMT_MISC is not set
CONFIG_HAVE_ATOMIC_IOMAP=y
CONFIG_HAVE_TEXT_POKE_SMP=y
# CONFIG_NET is not set

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH=""
# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
CONFIG_FW_LOADER=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_ARCH_NO_SYSDEV_OPS=y
# CONFIG_MTD is not set
# CONFIG_PARPORT is not set
# CONFIG_BLK_DEV is not set
# CONFIG_SENSORS_LIS3LV02D is not set
# CONFIG_MISC_DEVICES is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set

#
# SCSI device support
#
CONFIG_SCSI_MOD=y
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
# CONFIG_SCSI_DMA is not set
# CONFIG_SCSI_NETLINK is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
# CONFIG_MACINTOSH_DRIVERS is not set
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_POLLDEV is not set
# CONFIG_INPUT_SPARSEKMAP is not set

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_SERIO_ALTERA_PS2 is not set
# CONFIG_SERIO_PS2MULT is not set
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
CONFIG_UNIX98_PTYS=y
# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
# CONFIG_LEGACY_PTYS is not set
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_DEVKMEM is not set

#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set
CONFIG_FIX_EARLYCON_MEM=y

#
# Non-8250 serial port support
#
# CONFIG_SERIAL_TIMBERDALE is not set
# CONFIG_SERIAL_ALTERA_JTAGUART is not set
# CONFIG_SERIAL_ALTERA_UART is not set
# CONFIG_IPMI_HANDLER is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_NVRAM is not set
# CONFIG_RTC is not set
# CONFIG_GEN_RTC is not set
# CONFIG_R3964 is not set
# CONFIG_MWAVE is not set
# CONFIG_PC8736x_GPIO is not set
# CONFIG_NSC_GPIO is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_HANGCHECK_TIMER is not set
# CONFIG_RAMOOPS is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set

#
# PPS support
#

#
# PPS generators support
#
CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
# CONFIG_GPIOLIB is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y

#
# Sonics Silicon Backplane
#
# CONFIG_SSB is not set
# CONFIG_MFD_SUPPORT is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set

#
# Graphics support
#
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set

#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VGACON_SOFT_SCROLLBACK is not set
CONFIG_DUMMY_CONSOLE=y
# CONFIG_SOUND is not set
# CONFIG_HID_SUPPORT is not set
# CONFIG_USB_SUPPORT is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_NFC_DEVICES is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_EDAC is not set
# CONFIG_RTC_CLASS is not set
# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set
# CONFIG_STAGING is not set
# CONFIG_X86_PLATFORM_DEVICES is not set

#
# Firmware Drivers
#
# CONFIG_EDD is not set
CONFIG_FIRMWARE_MEMMAP=y
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set
# CONFIG_DMIID is not set
# CONFIG_DMI_SYSFS is not set
# CONFIG_ISCSI_IBFT_FIND is not set

#
# File systems
#
# CONFIG_EXT2_FS is not set
# CONFIG_EXT3_FS is not set
# CONFIG_EXT4_FS is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_XFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
CONFIG_FILE_LOCKING=y
# CONFIG_FSNOTIFY is not set
# CONFIG_DNOTIFY is not set
# CONFIG_INOTIFY_USER is not set
# CONFIG_FANOTIFY is not set
# CONFIG_QUOTA is not set
# CONFIG_QUOTACTL is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set

#
# Caches
#
# CONFIG_FSCACHE is not set

#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set

#
# DOS/FAT/NT Filesystems
#
# CONFIG_MSDOS_FS is not set
# CONFIG_VFAT_FS is not set
# CONFIG_NTFS_FS is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
# CONFIG_PROC_KCORE is not set
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
# CONFIG_TMPFS is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
# CONFIG_MISC_FILESYSTEMS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
# CONFIG_NLS is not set

#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_PRINTK_TIME=y
CONFIG_DEFAULT_MESSAGE_LOGLEVEL=4
# CONFIG_ENABLE_WARN_DEPRECATED is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_SECTION_MISMATCH is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_LOCKUP_DETECTOR=y
CONFIG_HARDLOCKUP_DETECTOR=y
CONFIG_BOOTPARAM_HARDLOCKUP_PANIC=y
CONFIG_BOOTPARAM_HARDLOCKUP_PANIC_VALUE=1
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC=y
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=1
CONFIG_DETECT_HUNG_TASK=y
CONFIG_BOOTPARAM_HUNG_TASK_PANIC=y
CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=1
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_SLUB_DEBUG_ON is not set
# CONFIG_SLUB_STATS is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_SPARSE_RCU_POINTER is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_HIGHMEM is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_VIRTUAL is not set
# CONFIG_DEBUG_WRITECOUNT is not set
CONFIG_DEBUG_MEMORY_INIT=y
# CONFIG_DEBUG_LIST is not set
# CONFIG_TEST_LIST_SORT is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_ARCH_WANT_FRAME_POINTERS=y
# CONFIG_FRAME_POINTER is not set
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
# CONFIG_DEBUG_PAGEALLOC is not set
CONFIG_USER_STACKTRACE_SUPPORT=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_FP_TEST=y
CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_HAVE_C_RECORDMCOUNT=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
# CONFIG_ATOMIC64_SELFTEST is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
CONFIG_HAVE_ARCH_KMEMCHECK=y
# CONFIG_KMEMCHECK is not set
# CONFIG_TEST_KSTRTOX is not set
# CONFIG_STRICT_DEVMEM is not set
CONFIG_X86_VERBOSE_BOOTUP=y
CONFIG_EARLY_PRINTK=y
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_X86_PTDUMP is not set
CONFIG_DEBUG_RODATA=y
CONFIG_DEBUG_RODATA_TEST=y
CONFIG_DOUBLEFAULT=y
# CONFIG_IOMMU_STRESS is not set
CONFIG_HAVE_MMIOTRACE_SUPPORT=y
CONFIG_IO_DELAY_TYPE_0X80=0
CONFIG_IO_DELAY_TYPE_0XED=1
CONFIG_IO_DELAY_TYPE_UDELAY=2
CONFIG_IO_DELAY_TYPE_NONE=3
CONFIG_IO_DELAY_0X80=y
# CONFIG_IO_DELAY_0XED is not set
# CONFIG_IO_DELAY_UDELAY is not set
# CONFIG_IO_DELAY_NONE is not set
CONFIG_DEFAULT_IO_DELAY_TYPE=0
# CONFIG_CPA_DEBUG is not set
# CONFIG_OPTIMIZE_INLINING is not set
# CONFIG_DEBUG_STRICT_USER_COPY_CHECKS is not set

#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY_DMESG_RESTRICT is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITYFS is not set
CONFIG_DEFAULT_SECURITY_DAC=y
CONFIG_DEFAULT_SECURITY=""
# CONFIG_CRYPTO is not set
CONFIG_HAVE_KVM=y
# CONFIG_VIRTUALIZATION is not set
# CONFIG_BINARY_PRINTF is not set

#
# Library routines
#
CONFIG_GENERIC_FIND_FIRST_BIT=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_FIND_LAST_BIT=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
# CONFIG_CRC32 is not set
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
# CONFIG_XZ_DEC is not set
# CONFIG_XZ_DEC_BCJ is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
# CONFIG_AVERAGE is not set

#
# Automatically generated make config: don't edit # Linux kernel version: 2.6.18
# Fri Feb 19 23:18:37 2010
#
CONFIG_X86_32=y
CONFIG_GENERIC_TIME=y
CONFIG_LOCKDEP_SUPPORT=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_HWEIGHT=y CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_DMI=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32

#
# General setup
#
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
# CONFIG_TASKSTATS is not set
CONFIG_AUDIT=y
# CONFIG_AUDITSYSCALL is not set
# CONFIG_IKCONFIG is not set
CONFIG_CPUSETS=y
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set

#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y

#
# Block layer
#
CONFIG_LBD=y
# CONFIG_BLK_DEV_IO_TRACE is not set
CONFIG_LSF=y

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"

#
# Processor type and features
#
CONFIG_SMP=y
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
CONFIG_M686=y
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MGEODE_LX is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=5
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_PPRO_FENCE=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_CMPXCHG64=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_TSC=y
CONFIG_HPET_TIMER=y
CONFIG_NR_CPUS=8
CONFIG_SCHED_SMT=y
CONFIG_SCHED_MC=y
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
# CONFIG_PREEMPT_BKL is not set
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=m
CONFIG_X86_MCE_P4THERMAL=y
CONFIG_VM86=y
CONFIG_TOSHIBA=m
CONFIG_I8K=m
# CONFIG_X86_REBOOTFIXUPS is not set
CONFIG_MICROCODE=m
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m

#
# Firmware Drivers
#
CONFIG_EDD=m
CONFIG_EFI_VARS=m
CONFIG_DELL_RBU=m
CONFIG_DCDBAS=m
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_HIGHMEM=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
# CONFIG_HIGHPTE is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
CONFIG_EFI=y
CONFIG_IRQBALANCE=y
CONFIG_BOOT_IOREMAP=y
CONFIG_REGPARM=y
# CONFIG_SECCOMP is not set
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
CONFIG_KEXEC=y
# CONFIG_CRASH_DUMP is not set
CONFIG_PHYSICAL_START=0x100000
CONFIG_HOTPLUG_CPU=y
CONFIG_COMPAT_VDSO=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y

#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
CONFIG_SOFTWARE_SUSPEND=y
CONFIG_PM_STD_PARTITION=""
CONFIG_SUSPEND_SMP=y

#
# ACPI (Advanced Configuration and Power Interface) Support #
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
# CONFIG_ACPI_SLEEP_PROC_SLEEP is not set CONFIG_ACPI_AC=m
CONFIG_ACPI_BATTERY=m
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_VIDEO=m
CONFIG_ACPI_HOTKEY=m
CONFIG_ACPI_FAN=m
CONFIG_ACPI_DOCK=m
CONFIG_ACPI_PROCESSOR=m
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=m
CONFIG_ACPI_ASUS=m
CONFIG_ACPI_IBM=m
CONFIG_ACPI_TOSHIBA=m
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=m
CONFIG_ACPI_SBS=m

#
# APM (Advanced Power Management) BIOS Support
#
CONFIG_APM=m
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
# CONFIG_APM_CPU_IDLE is not set
# CONFIG_APM_DISPLAY_BLANK is not set
# CONFIG_APM_RTC_IS_GMT is not set
# CONFIG_APM_ALLOW_INTS is not set
# CONFIG_APM_REAL_MODE_POWER_OFF is not set

#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=m
# CONFIG_CPU_FREQ_DEBUG is not set CONFIG_CPU_FREQ_STAT=m
# CONFIG_CPU_FREQ_STAT_DETAILS is not set CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y # CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set CONFIG_CPU_FREQ_GOV_PERFORMANCE=y CONFIG_CPU_FREQ_GOV_POWERSAVE=m CONFIG_CPU_FREQ_GOV_USERSPACE=m CONFIG_CPU_FREQ_GOV_ONDEMAND=m CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m

#
# CPUFreq processor drivers
#
CONFIG_X86_ACPI_CPUFREQ=m
CONFIG_X86_POWERNOW_K6=m
CONFIG_X86_POWERNOW_K7=m
CONFIG_X86_POWERNOW_K7_ACPI=y
CONFIG_X86_POWERNOW_K8=m
CONFIG_X86_POWERNOW_K8_ACPI=y
CONFIG_X86_GX_SUSPMOD=m
CONFIG_X86_SPEEDSTEP_CENTRINO=m
CONFIG_X86_SPEEDSTEP_CENTRINO_ACPI=y
CONFIG_X86_SPEEDSTEP_CENTRINO_TABLE=y
CONFIG_X86_SPEEDSTEP_ICH=m
CONFIG_X86_SPEEDSTEP_SMI=m
CONFIG_X86_P4_CLOCKMOD=m
CONFIG_X86_CPUFREQ_NFORCE2=m
CONFIG_X86_LONGRUN=m
CONFIG_X86_LONGHAUL=m

# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
CONFIG_X86_SPEEDSTEP_LIB=m
CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK=y

#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA) #
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCIEPORTBUS=y CONFIG_HOTPLUG_PCI_PCIE=m
# CONFIG_HOTPLUG_PCI_PCIE_POLL_EVENT_MODE is not set CONFIG_PCI_MSI=y
CONFIG_ISA_DMA_API=y
CONFIG_ISA=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
CONFIG_SCx200=m
CONFIG_SCx200HR_TIMER=m
CONFIG_K8_NB=y

#
# PCCARD (PCMCIA/CardBus) support
#
CONFIG_PCCARD=m
# CONFIG_PCMCIA_DEBUG is not set
CONFIG_PCMCIA=m
CONFIG_PCMCIA_LOAD_CIS=y
CONFIG_PCMCIA_IOCTL=y
CONFIG_CARDBUS=y

#
# PC-card bridges
#
CONFIG_YENTA=m
CONFIG_YENTA_O2=y
CONFIG_YENTA_RICOH=y
CONFIG_YENTA_TI=y
CONFIG_YENTA_ENE_TUNE=y
CONFIG_YENTA_TOSHIBA=y
CONFIG_PD6729=m
CONFIG_I82092=m
CONFIG_I82365=m
CONFIG_TCIC=m
CONFIG_PCMCIA_PROBE=y
CONFIG_PCCARD_NONSTATIC=m

#
# PCI Hotplug Support
#
CONFIG_HOTPLUG_PCI=m CONFIG_HOTPLUG_PCI_FAKE=m CONFIG_HOTPLUG_PCI_COMPAQ=m
# CONFIG_HOTPLUG_PCI_COMPAQ_NVRAM is not set CONFIG_HOTPLUG_PCI_IBM=m CONFIG_HOTPLUG_PCI_ACPI=m CONFIG_HOTPLUG_PCI_ACPI_IBM=m CONFIG_HOTPLUG_PCI_CPCI=y CONFIG_HOTPLUG_PCI_CPCI_ZT5550=m CONFIG_HOTPLUG_PCI_CPCI_GENERIC=m CONFIG_HOTPLUG_PCI_SHPC=m
# CONFIG_HOTPLUG_PCI_SHPC_POLL_EVENT_MODE is not set

#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m

#
# Networking
#
CONFIG_NET=y

#
# Networking options
#
# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
CONFIG_NET_KEY=m
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_ASK_IP_FIB_HASH=y
# CONFIG_IP_FIB_TRIE is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_FWMARK=y
CONFIG_IP_ROUTE_MULTIPATH=y
# CONFIG_IP_ROUTE_MULTIPATH_CACHED is not set
CONFIG_IP_ROUTE_VERBOSE=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_TUNNEL=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_DIAG=m
CONFIG_INET_TCP_DIAG=m
CONFIG_TCP_CONG_ADVANCED=y

#
# TCP congestion control
#
CONFIG_TCP_CONG_BIC=y
CONFIG_TCP_CONG_CUBIC=m
CONFIG_TCP_CONG_WESTWOOD=m
CONFIG_TCP_CONG_HTCP=m
CONFIG_TCP_CONG_HSTCP=m
CONFIG_TCP_CONG_HYBLA=m
CONFIG_TCP_CONG_VEGAS=m
CONFIG_TCP_CONG_SCALABLE=m
CONFIG_TCP_CONG_LP=m
CONFIG_TCP_CONG_VENO=m

#
# IP: Virtual Server Configuration
#
CONFIG_IP_VS=m
# CONFIG_IP_VS_DEBUG is not set
CONFIG_IP_VS_TAB_BITS=12

#
# IPVS transport protocol load balancing support
#
CONFIG_IP_VS_PROTO_TCP=y
CONFIG_IP_VS_PROTO_UDP=y
CONFIG_IP_VS_PROTO_ESP=y
CONFIG_IP_VS_PROTO_AH=y

#
# IPVS scheduler
#
CONFIG_IP_VS_RR=m
CONFIG_IP_VS_WRR=m
CONFIG_IP_VS_LC=m
CONFIG_IP_VS_WLC=m
CONFIG_IP_VS_LBLC=m
CONFIG_IP_VS_LBLCR=m
CONFIG_IP_VS_DH=m
CONFIG_IP_VS_SH=m
CONFIG_IP_VS_SED=m
CONFIG_IP_VS_NQ=m

#
# IPVS application helper
#
CONFIG_IP_VS_FTP=m
CONFIG_IPV6=m
CONFIG_IPV6_PRIVACY=y
# CONFIG_IPV6_ROUTER_PREF is not set
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
CONFIG_INET6_XFRM_TUNNEL=m
CONFIG_INET6_TUNNEL=m
CONFIG_INET6_XFRM_MODE_TRANSPORT=m
CONFIG_INET6_XFRM_MODE_TUNNEL=m
CONFIG_IPV6_TUNNEL=m
CONFIG_NETWORK_SECMARK=y
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_BRIDGE_NETFILTER=y

#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_NETLINK=m
CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NETFILTER_NETLINK_LOG=m
CONFIG_NETFILTER_XTABLES=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
CONFIG_NETFILTER_XT_TARGET_SECMARK=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
CONFIG_NETFILTER_XT_MATCH_DCCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HELPER=m
CONFIG_NETFILTER_XT_MATCH_LENGTH=m
CONFIG_NETFILTER_XT_MATCH_LIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_QUOTA=m
CONFIG_NETFILTER_XT_MATCH_REALM=m
CONFIG_NETFILTER_XT_MATCH_SCTP=m
CONFIG_NETFILTER_XT_MATCH_STATE=m
CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
CONFIG_NETFILTER_XT_MATCH_STRING=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m

#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
CONFIG_IP_NF_CT_ACCT=y
CONFIG_IP_NF_CONNTRACK_MARK=y
# CONFIG_IP_NF_CONNTRACK_SECMARK is not set
CONFIG_IP_NF_CONNTRACK_EVENTS=y
CONFIG_IP_NF_CONNTRACK_NETLINK=m
CONFIG_IP_NF_CT_PROTO_SCTP=m
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
CONFIG_IP_NF_NETBIOS_NS=m
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
CONFIG_IP_NF_PPTP=m
CONFIG_IP_NF_H323=m
CONFIG_IP_NF_SIP=m
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_HASHLIMIT=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
CONFIG_IP_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_NAT_AMANDA=m
CONFIG_IP_NF_NAT_PPTP=m
CONFIG_IP_NF_NAT_H323=m
CONFIG_IP_NF_NAT_SIP=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_TTL=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m

#
# IPv6: Netfilter Configuration (EXPERIMENTAL)
#
CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_MATCH_OPTS=m
CONFIG_IP6_NF_MATCH_FRAG=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_OWNER=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_TARGET_HL=m
CONFIG_IP6_NF_RAW=m

#
# DECnet: Netfilter Configuration
#
CONFIG_DECNET_NF_GRABULATOR=m

#
# Bridge: Netfilter Configuration
#
CONFIG_BRIDGE_NF_EBTABLES=m
CONFIG_BRIDGE_EBT_BROUTE=m
CONFIG_BRIDGE_EBT_T_FILTER=m
CONFIG_BRIDGE_EBT_T_NAT=m
CONFIG_BRIDGE_EBT_802_3=m
CONFIG_BRIDGE_EBT_AMONG=m
CONFIG_BRIDGE_EBT_ARP=m
CONFIG_BRIDGE_EBT_IP=m
CONFIG_BRIDGE_EBT_LIMIT=m
CONFIG_BRIDGE_EBT_MARK=m
CONFIG_BRIDGE_EBT_PKTTYPE=m
CONFIG_BRIDGE_EBT_STP=m
CONFIG_BRIDGE_EBT_VLAN=m
CONFIG_BRIDGE_EBT_ARPREPLY=m
CONFIG_BRIDGE_EBT_DNAT=m
CONFIG_BRIDGE_EBT_MARK_T=m
CONFIG_BRIDGE_EBT_REDIRECT=m
CONFIG_BRIDGE_EBT_SNAT=m
CONFIG_BRIDGE_EBT_LOG=m
CONFIG_BRIDGE_EBT_ULOG=m

#
# DCCP Configuration (EXPERIMENTAL)
#
CONFIG_IP_DCCP=m
CONFIG_INET_DCCP_DIAG=m
CONFIG_IP_DCCP_ACKVEC=y

#
# DCCP CCIDs Configuration (EXPERIMENTAL)
#
CONFIG_IP_DCCP_CCID2=m
CONFIG_IP_DCCP_CCID3=m
CONFIG_IP_DCCP_TFRC_LIB=m

#
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_IP_SCTP=m
# CONFIG_SCTP_DBG_MSG is not set
# CONFIG_SCTP_DBG_OBJCNT is not set
# CONFIG_SCTP_HMAC_NONE is not set
# CONFIG_SCTP_HMAC_SHA1 is not set
CONFIG_SCTP_HMAC_MD5=y

#
# TIPC Configuration (EXPERIMENTAL)
#
CONFIG_TIPC=m
CONFIG_TIPC_ADVANCED=y
CONFIG_TIPC_ZONES=3
CONFIG_TIPC_CLUSTERS=1
CONFIG_TIPC_NODES=255
CONFIG_TIPC_SLAVE_NODES=0
CONFIG_TIPC_PORTS=8191
CONFIG_TIPC_LOG=0
# CONFIG_TIPC_DEBUG is not set
CONFIG_ATM=y
CONFIG_ATM_CLIP=y
# CONFIG_ATM_CLIP_NO_ICMP is not set
CONFIG_ATM_LANE=m
CONFIG_ATM_MPOA=m
CONFIG_ATM_BR2684=m
# CONFIG_ATM_BR2684_IPFILTER is not set
CONFIG_BRIDGE=m
CONFIG_VLAN_8021Q=m
CONFIG_DECNET=m
# CONFIG_DECNET_ROUTER is not set
CONFIG_LLC=y
CONFIG_LLC2=m
CONFIG_IPX=m
# CONFIG_IPX_INTERN is not set
CONFIG_ATALK=m
CONFIG_DEV_APPLETALK=m
CONFIG_LTPC=m
CONFIG_IPDDP=m
CONFIG_IPDDP_ENCAP=y
CONFIG_IPDDP_DECAP=y
CONFIG_X25=m
CONFIG_LAPB=m
CONFIG_ECONET=m
CONFIG_ECONET_AUNUDP=y
CONFIG_ECONET_NATIVE=y
CONFIG_WAN_ROUTER=m

#
# QoS and/or fair queueing
#
CONFIG_NET_SCHED=y
CONFIG_NET_SCH_CLK_JIFFIES=y
# CONFIG_NET_SCH_CLK_GETTIMEOFDAY is not set
# CONFIG_NET_SCH_CLK_CPU is not set

#
# Queueing/Scheduling
#
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_HFSC=m
CONFIG_NET_SCH_ATM=m
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_NETEM=m
CONFIG_NET_SCH_INGRESS=m

#
# Classification
#
CONFIG_NET_CLS=y
CONFIG_NET_CLS_BASIC=m
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
CONFIG_CLS_U32_PERF=y
CONFIG_CLS_U32_MARK=y
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
CONFIG_NET_EMATCH=y
CONFIG_NET_EMATCH_STACK=32
CONFIG_NET_EMATCH_CMP=m
CONFIG_NET_EMATCH_NBYTE=m
CONFIG_NET_EMATCH_U32=m
CONFIG_NET_EMATCH_META=m
CONFIG_NET_EMATCH_TEXT=m
CONFIG_NET_CLS_ACT=y
CONFIG_NET_ACT_POLICE=m
CONFIG_NET_ACT_GACT=m
CONFIG_GACT_PROB=y
CONFIG_NET_ACT_MIRRED=m
CONFIG_NET_ACT_IPT=m
CONFIG_NET_ACT_PEDIT=m
CONFIG_NET_ACT_SIMP=m
CONFIG_NET_CLS_IND=y
CONFIG_NET_ESTIMATOR=y

#
# Network testing
#
CONFIG_NET_PKTGEN=m
CONFIG_HAMRADIO=y

#
# Packet Radio protocols
#
CONFIG_AX25=m
# CONFIG_AX25_DAMA_SLAVE is not set
CONFIG_NETROM=m
CONFIG_ROSE=m

#
# AX.25 network device drivers
#
CONFIG_MKISS=m
CONFIG_6PACK=m
CONFIG_BPQETHER=m
CONFIG_SCC=m
# CONFIG_SCC_DELAY is not set
# CONFIG_SCC_TRXECHO is not set
CONFIG_BAYCOM_SER_FDX=m
CONFIG_BAYCOM_SER_HDX=m
CONFIG_BAYCOM_PAR=m
CONFIG_BAYCOM_EPP=m
CONFIG_YAM=m
CONFIG_IRDA=m

#
# IrDA protocols
#
CONFIG_IRLAN=m
CONFIG_IRNET=m
CONFIG_IRCOMM=m
# CONFIG_IRDA_ULTRA is not set

#
# IrDA options
#
CONFIG_IRDA_CACHE_LAST_LSAP=y
CONFIG_IRDA_FAST_RR=y
CONFIG_IRDA_DEBUG=y

#
# Infrared-port device drivers
#

#
# SIR device drivers
#
CONFIG_IRTTY_SIR=m

#
# Dongle support
#
CONFIG_DONGLE=y
CONFIG_ESI_DONGLE=m
CONFIG_ACTISYS_DONGLE=m
CONFIG_TEKRAM_DONGLE=m
CONFIG_TOIM3232_DONGLE=m
CONFIG_LITELINK_DONGLE=m
CONFIG_MA600_DONGLE=m
CONFIG_GIRBIL_DONGLE=m
CONFIG_MCP2120_DONGLE=m
CONFIG_OLD_BELKIN_DONGLE=m
CONFIG_ACT200L_DONGLE=m

#
# Old SIR device drivers
#

#
# Old Serial dongle support
#

#
# FIR device drivers
#
CONFIG_USB_IRDA=m
CONFIG_SIGMATEL_FIR=m
CONFIG_NSC_FIR=m
CONFIG_WINBOND_FIR=m
CONFIG_TOSHIBA_FIR=m
CONFIG_SMC_IRCC_FIR=m
CONFIG_ALI_FIR=m
CONFIG_VLSI_FIR=m
CONFIG_VIA_FIR=m
CONFIG_MCS_FIR=m
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_CMTP=m
CONFIG_BT_HIDP=m

#
# Bluetooth device drivers
#
CONFIG_BT_HCIUSB=m
CONFIG_BT_HCIUSB_SCO=y
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
CONFIG_BT_HCIBCM203X=m
CONFIG_BT_HCIBPA10X=m
CONFIG_BT_HCIBFUSB=m
CONFIG_BT_HCIDTL1=m
CONFIG_BT_HCIBT3C=m
CONFIG_BT_HCIBLUECARD=m
CONFIG_BT_HCIBTUART=m
CONFIG_BT_HCIVHCI=m
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_CRYPT_CCMP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
CONFIG_IEEE80211_SOFTMAC=m
# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set
CONFIG_WIRELESS_EXT=y

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
# CONFIG_SYS_HYPERVISOR is not set

#
# Connector - unified userspace <-> kernelspace linker #
CONFIG_CONNECTOR=m

#
# Memory Technology Devices (MTD)
#
CONFIG_MTD=m
# CONFIG_MTD_DEBUG is not set
CONFIG_MTD_CONCAT=m
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_REDBOOT_PARTS=m
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
# CONFIG_MTD_CMDLINE_PARTS is not set

#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=m
CONFIG_MTD_BLOCK=m
CONFIG_MTD_BLOCK_RO=m
CONFIG_FTL=m
CONFIG_NFTL=m
CONFIG_NFTL_RW=y
CONFIG_INFTL=m
CONFIG_RFD_FTL=m

#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=m
CONFIG_MTD_JEDECPROBE=m
CONFIG_MTD_GEN_PROBE=m
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
CONFIG_MTD_CFI_INTELEXT=m
CONFIG_MTD_CFI_AMDSTD=m
CONFIG_MTD_CFI_STAA=m
CONFIG_MTD_CFI_UTIL=m
CONFIG_MTD_RAM=m
CONFIG_MTD_ROM=m
CONFIG_MTD_ABSENT=m
# CONFIG_MTD_OBSOLETE_CHIPS is not set

#
# Mapping drivers for chip access
#
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=m
CONFIG_MTD_PHYSMAP_START=0x8000000
CONFIG_MTD_PHYSMAP_LEN=0x4000000
CONFIG_MTD_PHYSMAP_BANKWIDTH=2
CONFIG_MTD_PNC2000=m
CONFIG_MTD_SC520CDP=m
CONFIG_MTD_NETSC520=m
CONFIG_MTD_TS5500=m
CONFIG_MTD_SBC_GXX=m
CONFIG_MTD_SCx200_DOCFLASH=m
# CONFIG_MTD_AMD76XROM is not set
# CONFIG_MTD_ICHXROM is not set
# CONFIG_MTD_SCB2_FLASH is not set
CONFIG_MTD_NETtel=m
CONFIG_MTD_DILNETPC=m
CONFIG_MTD_DILNETPC_BOOTSIZE=0x80000
# CONFIG_MTD_L440GX is not set
CONFIG_MTD_PCI=m
CONFIG_MTD_PLATRAM=m

#
# Self-contained MTD device drivers
#
CONFIG_MTD_PMC551=m
# CONFIG_MTD_PMC551_BUGFIX is not set
# CONFIG_MTD_PMC551_DEBUG is not set
CONFIG_MTD_DATAFLASH=m
CONFIG_MTD_M25P80=m
CONFIG_MTD_SLRAM=m
CONFIG_MTD_PHRAM=m
CONFIG_MTD_MTDRAM=m
CONFIG_MTDRAM_TOTAL_SIZE=4096
CONFIG_MTDRAM_ERASE_SIZE=128
CONFIG_MTD_BLOCK2MTD=m

#
# Disk-On-Chip Device Drivers
#
CONFIG_MTD_DOC2000=m
CONFIG_MTD_DOC2001=m
CONFIG_MTD_DOC2001PLUS=m
CONFIG_MTD_DOCPROBE=m
CONFIG_MTD_DOCECC=m
# CONFIG_MTD_DOCPROBE_ADVANCED is not set
CONFIG_MTD_DOCPROBE_ADDRESS=0

#
# NAND Flash Device Drivers
#
CONFIG_MTD_NAND=m
# CONFIG_MTD_NAND_VERIFY_WRITE is not set
# CONFIG_MTD_NAND_ECC_SMC is not set CONFIG_MTD_NAND_IDS=m CONFIG_MTD_NAND_DISKONCHIP=m
# CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED is not set CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0
# CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE is not set CONFIG_MTD_NAND_CS553X=m
# CONFIG_MTD_NAND_NANDSIM is not set

#
# OneNAND Flash Device Drivers
#
CONFIG_MTD_ONENAND=m
CONFIG_MTD_ONENAND_VERIFY_WRITE=y
# CONFIG_MTD_ONENAND_OTP is not set

#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_SERIAL=m
CONFIG_PARPORT_PC_FIFO=y
# CONFIG_PARPORT_PC_SUPERIO is not set
CONFIG_PARPORT_PC_PCMCIA=m
CONFIG_PARPORT_NOT_PC=y
# CONFIG_PARPORT_GSC is not set
CONFIG_PARPORT_AX88796=m
CONFIG_PARPORT_1284=y

#
# Plug and Play support
#
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set

#
# Protocols
#
CONFIG_ISAPNP=y
CONFIG_PNPBIOS=y
CONFIG_PNPBIOS_PROC_FS=y
CONFIG_PNPACPI=y

#
# Block devices
#
CONFIG_BLK_DEV_FD=m
CONFIG_BLK_DEV_XD=m
CONFIG_PARIDE=m
CONFIG_PARIDE_PARPORT=m

#
# Parallel IDE high-level drivers
#
CONFIG_PARIDE_PD=m
CONFIG_PARIDE_PCD=m
CONFIG_PARIDE_PF=m
CONFIG_PARIDE_PT=m
CONFIG_PARIDE_PG=m

#
# Parallel IDE protocol modules
#
CONFIG_PARIDE_ATEN=m
CONFIG_PARIDE_BPCK=m
CONFIG_PARIDE_BPCK6=m
CONFIG_PARIDE_COMM=m
CONFIG_PARIDE_DSTR=m
CONFIG_PARIDE_FIT2=m
CONFIG_PARIDE_FIT3=m
CONFIG_PARIDE_EPAT=m
# CONFIG_PARIDE_EPATC8 is not set
CONFIG_PARIDE_EPIA=m
CONFIG_PARIDE_FRIQ=m
CONFIG_PARIDE_FRPW=m
CONFIG_PARIDE_KBIC=m
CONFIG_PARIDE_KTTI=m
CONFIG_PARIDE_ON20=m
CONFIG_PARIDE_ON26=m
CONFIG_BLK_CPQ_DA=m
CONFIG_BLK_CPQ_CISS_DA=m
CONFIG_CISS_SCSI_TAPE=y
CONFIG_BLK_DEV_DAC960=m
CONFIG_BLK_DEV_UMEM=m
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_SX8=m
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_BLK_DEV_INITRD=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m

#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=m
CONFIG_BLK_DEV_IDE=m

#
# Please see Documentation/ide.txt for help/info on IDE drives #
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set CONFIG_BLK_DEV_IDEDISK=m
# CONFIG_IDEDISK_MULTI_MODE is not set CONFIG_BLK_DEV_IDECS=m
CONFIG_BLK_DEV_IDECD=m
CONFIG_BLK_DEV_IDETAPE=m
CONFIG_BLK_DEV_IDEFLOPPY=m
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=m
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
CONFIG_BLK_DEV_IDEPNP=m
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=m
CONFIG_BLK_DEV_OPTI621=m
CONFIG_BLK_DEV_RZ1000=m
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_AEC62XX=m
CONFIG_BLK_DEV_ALI15X3=m
# CONFIG_WDC_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=m
CONFIG_BLK_DEV_ATIIXP=m
CONFIG_BLK_DEV_CMD64X=m
CONFIG_BLK_DEV_TRIFLEX=m
CONFIG_BLK_DEV_CY82C693=m
CONFIG_BLK_DEV_CS5520=m
CONFIG_BLK_DEV_CS5530=m
CONFIG_BLK_DEV_CS5535=m
CONFIG_BLK_DEV_HPT34X=m
# CONFIG_HPT34X_AUTODMA is not set
CONFIG_BLK_DEV_HPT366=m
CONFIG_BLK_DEV_JMICRON=m
CONFIG_BLK_DEV_SC1200=m
CONFIG_BLK_DEV_PIIX=m
CONFIG_BLK_DEV_IT821X=m
CONFIG_BLK_DEV_NS87415=m
CONFIG_BLK_DEV_PDC202XX_OLD=m
CONFIG_PDC202XX_BURST=y
CONFIG_BLK_DEV_PDC202XX_NEW=m
CONFIG_BLK_DEV_SVWKS=m
CONFIG_BLK_DEV_SIIMAGE=m
CONFIG_BLK_DEV_SIS5513=m
CONFIG_BLK_DEV_SLC90E66=m
CONFIG_BLK_DEV_TRM290=m
CONFIG_BLK_DEV_VIA82CXXX=m
# CONFIG_IDE_ARM is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
CONFIG_RAID_ATTRS=m
CONFIG_SCSI=m
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=m
CONFIG_CHR_DEV_ST=m
CONFIG_CHR_DEV_OSST=m
CONFIG_BLK_DEV_SR=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_CHR_DEV_SCH=m

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs #
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y

#
# SCSI Transport Attributes
#
CONFIG_SCSI_SPI_ATTRS=m
CONFIG_SCSI_FC_ATTRS=m
CONFIG_SCSI_ISCSI_ATTRS=m
CONFIG_SCSI_SAS_ATTRS=m

#
# SCSI low-level drivers
#
CONFIG_ISCSI_TCP=m
CONFIG_BLK_DEV_3W_XXXX_RAID=m
CONFIG_SCSI_3W_9XXX=m
CONFIG_SCSI_7000FASST=m
CONFIG_SCSI_ACARD=m
CONFIG_SCSI_AHA152X=m
CONFIG_SCSI_AHA1542=m
CONFIG_SCSI_AACRAID=m
CONFIG_SCSI_AIC7XXX=m
CONFIG_AIC7XXX_CMDS_PER_DEVICE=8
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
CONFIG_AIC7XXX_DEBUG_ENABLE=y
CONFIG_AIC7XXX_DEBUG_MASK=0
CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
CONFIG_SCSI_AIC7XXX_OLD=m
CONFIG_SCSI_AIC79XX=m
CONFIG_AIC79XX_CMDS_PER_DEVICE=32
CONFIG_AIC79XX_RESET_DELAY_MS=15000
CONFIG_AIC79XX_ENABLE_RD_STRM=y
CONFIG_AIC79XX_DEBUG_ENABLE=y
CONFIG_AIC79XX_DEBUG_MASK=0
CONFIG_AIC79XX_REG_PRETTY_PRINT=y
CONFIG_SCSI_DPT_I2O=m
CONFIG_SCSI_ADVANSYS=m
CONFIG_SCSI_IN2000=m
CONFIG_SCSI_ARCMSR=m
CONFIG_MEGARAID_NEWGEN=y
CONFIG_MEGARAID_MM=m
CONFIG_MEGARAID_MAILBOX=m
CONFIG_MEGARAID_LEGACY=m
CONFIG_MEGARAID_SAS=m
CONFIG_SCSI_SATA=m
CONFIG_SCSI_SATA_AHCI=m
CONFIG_SCSI_SATA_SVW=m
CONFIG_SCSI_ATA_PIIX=m
CONFIG_SCSI_SATA_MV=m
CONFIG_SCSI_SATA_NV=m
CONFIG_SCSI_PDC_ADMA=m
CONFIG_SCSI_HPTIOP=m
CONFIG_SCSI_SATA_QSTOR=m
CONFIG_SCSI_SATA_PROMISE=m
CONFIG_SCSI_SATA_SX4=m
CONFIG_SCSI_SATA_SIL=m
CONFIG_SCSI_SATA_SIL24=m
CONFIG_SCSI_SATA_SIS=m
CONFIG_SCSI_SATA_ULI=m
CONFIG_SCSI_SATA_VIA=m
CONFIG_SCSI_SATA_VITESSE=m
CONFIG_SCSI_BUSLOGIC=m
# CONFIG_SCSI_OMIT_FLASHPOINT is not set
CONFIG_SCSI_DMX3191D=m
CONFIG_SCSI_DTC3280=m
CONFIG_SCSI_EATA=m
CONFIG_SCSI_EATA_TAGGED_QUEUE=y
CONFIG_SCSI_EATA_LINKED_COMMANDS=y
CONFIG_SCSI_EATA_MAX_TAGS=16
CONFIG_SCSI_FUTURE_DOMAIN=m
CONFIG_SCSI_GDTH=m
CONFIG_SCSI_GENERIC_NCR5380=m
CONFIG_SCSI_GENERIC_NCR5380_MMIO=m
CONFIG_SCSI_GENERIC_NCR53C400=y
CONFIG_SCSI_IPS=m
CONFIG_SCSI_INITIO=m
# CONFIG_SCSI_INIA100 is not set
CONFIG_SCSI_PPA=m
CONFIG_SCSI_IMM=m
# CONFIG_SCSI_IZIP_EPP16 is not set
# CONFIG_SCSI_IZIP_SLOW_CTR is not set
CONFIG_SCSI_NCR53C406A=m
CONFIG_SCSI_SYM53C8XX_2=m
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
CONFIG_SCSI_SYM53C8XX_MMIO=y
CONFIG_SCSI_IPR=m
# CONFIG_SCSI_IPR_TRACE is not set
# CONFIG_SCSI_IPR_DUMP is not set
CONFIG_SCSI_PAS16=m
CONFIG_SCSI_PSI240I=m
CONFIG_SCSI_QLOGIC_FAS=m
CONFIG_SCSI_QLOGIC_1280=m
CONFIG_SCSI_QLA_FC=m
CONFIG_SCSI_LPFC=m
CONFIG_SCSI_SYM53C416=m
CONFIG_SCSI_DC395x=m
CONFIG_SCSI_DC390T=m
CONFIG_SCSI_T128=m
CONFIG_SCSI_U14_34F=m
CONFIG_SCSI_U14_34F_TAGGED_QUEUE=y
CONFIG_SCSI_U14_34F_LINKED_COMMANDS=y
CONFIG_SCSI_U14_34F_MAX_TAGS=8
CONFIG_SCSI_ULTRASTOR=m
CONFIG_SCSI_NSP32=m
CONFIG_SCSI_DEBUG=m

#
# PCMCIA SCSI adapter support
#
CONFIG_PCMCIA_AHA152X=m
CONFIG_PCMCIA_FDOMAIN=m
CONFIG_PCMCIA_NINJA_SCSI=m
CONFIG_PCMCIA_QLOGIC=m
CONFIG_PCMCIA_SYM53C500=m

#
# Old CD-ROM drivers (not SCSI, not IDE)
#
CONFIG_CD_NO_IDESCSI=y
CONFIG_AZTCD=m
CONFIG_GSCD=m
CONFIG_MCDX=m
CONFIG_OPTCD=m
CONFIG_SJCD=m
CONFIG_ISP16_CDI=m
CONFIG_CDU535=m

#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=m
CONFIG_MD_RAID10=m
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
CONFIG_MD_MULTIPATH=m
CONFIG_MD_FAULTY=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_MULTIPATH_EMC=m

#
# Fusion MPT device support
#
CONFIG_FUSION=y
CONFIG_FUSION_SPI=m
CONFIG_FUSION_FC=m
CONFIG_FUSION_SAS=m
CONFIG_FUSION_MAX_SGE=40
CONFIG_FUSION_CTL=m
CONFIG_FUSION_LAN=m

#
# IEEE 1394 (FireWire) support
#
CONFIG_IEEE1394=m

#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_IEEE1394_OUI_DB is not set
CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y
CONFIG_IEEE1394_CONFIG_ROM_IP1394=y
# CONFIG_IEEE1394_EXPORT_FULL_API is not set

#
# Device Drivers
#
CONFIG_IEEE1394_PCILYNX=m
CONFIG_IEEE1394_OHCI1394=m

#
# Protocol Drivers
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
# CONFIG_IEEE1394_SBP2_PHYS_DMA is not set
CONFIG_IEEE1394_ETH1394=m
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=m

#
# I2O device support
#
CONFIG_I2O=m
CONFIG_I2O_LCT_NOTIFY_ON_CHANGES=y
CONFIG_I2O_EXT_ADAPTEC=y
CONFIG_I2O_CONFIG=m
CONFIG_I2O_CONFIG_OLD_IOCTL=y
CONFIG_I2O_BUS=m
CONFIG_I2O_BLOCK=m
CONFIG_I2O_SCSI=m
CONFIG_I2O_PROC=m

#
# Network device support
#
CONFIG_NETDEVICES=y
CONFIG_IFB=m
CONFIG_DUMMY=m
CONFIG_BONDING=m
CONFIG_EQUALIZER=m
CONFIG_TUN=m
CONFIG_NET_SB1000=m

#
# ARCnet devices
#
CONFIG_ARCNET=m
CONFIG_ARCNET_1201=m
CONFIG_ARCNET_1051=m
CONFIG_ARCNET_RAW=m
CONFIG_ARCNET_CAP=m
CONFIG_ARCNET_COM90xx=m
CONFIG_ARCNET_COM90xxIO=m
CONFIG_ARCNET_RIM_I=m
CONFIG_ARCNET_COM20020=m
CONFIG_ARCNET_COM20020_ISA=m
CONFIG_ARCNET_COM20020_PCI=m

#
# PHY device support
#
CONFIG_PHYLIB=m

#
# MII PHY device drivers
#
CONFIG_MARVELL_PHY=m
CONFIG_DAVICOM_PHY=m
CONFIG_QSEMI_PHY=m
CONFIG_LXT_PHY=m
CONFIG_CICADA_PHY=m
CONFIG_VITESSE_PHY=m
CONFIG_SMSC_PHY=m
CONFIG_FIXED_PHY=m
# CONFIG_FIXED_MII_10_FDX is not set
# CONFIG_FIXED_MII_100_FDX is not set

#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
CONFIG_HAPPYMEAL=m
CONFIG_SUNGEM=m
CONFIG_CASSINI=m
CONFIG_NET_VENDOR_3COM=y
CONFIG_EL1=m
CONFIG_EL2=m
CONFIG_ELPLUS=m
CONFIG_EL16=m
CONFIG_EL3=m
CONFIG_3C515=m
CONFIG_VORTEX=m
CONFIG_TYPHOON=m
CONFIG_LANCE=m
CONFIG_NET_VENDOR_SMC=y
CONFIG_WD80x3=m
CONFIG_ULTRA=m
CONFIG_SMC9194=m
CONFIG_NET_VENDOR_RACAL=y
CONFIG_NI52=m
CONFIG_NI65=m

#
# Tulip family network device support
#
CONFIG_NET_TULIP=y
CONFIG_DE2104X=m
CONFIG_TULIP=m
# CONFIG_TULIP_MWI is not set
# CONFIG_TULIP_MMIO is not set
CONFIG_TULIP_NAPI=y
CONFIG_TULIP_NAPI_HW_MITIGATION=y
CONFIG_DE4X5=m
CONFIG_WINBOND_840=m
CONFIG_DM9102=m
CONFIG_ULI526X=m
CONFIG_PCMCIA_XIRCOM=m
CONFIG_AT1700=m
CONFIG_DEPCA=m
CONFIG_HP100=m
CONFIG_NET_ISA=y
CONFIG_E2100=m
CONFIG_EWRK3=m
CONFIG_EEXPRESS=m
CONFIG_EEXPRESS_PRO=m
CONFIG_HPLAN_PLUS=m
CONFIG_HPLAN=m
CONFIG_LP486E=m
CONFIG_ETH16I=m
CONFIG_NE2000=m
CONFIG_ZNET=m
CONFIG_SEEQ8005=m
CONFIG_NET_PCI=y
CONFIG_PCNET32=m
CONFIG_AMD8111_ETH=m
CONFIG_AMD8111E_NAPI=y
CONFIG_ADAPTEC_STARFIRE=m
CONFIG_ADAPTEC_STARFIRE_NAPI=y
CONFIG_AC3200=m
CONFIG_APRICOT=m
CONFIG_B44=m
CONFIG_FORCEDETH=m
CONFIG_CS89x0=m
CONFIG_EEPRO100=m
CONFIG_E100=m
CONFIG_FEALNX=m
CONFIG_NATSEMI=m
CONFIG_NE2K_PCI=m
CONFIG_8139CP=m
CONFIG_8139TOO=m
CONFIG_8139TOO_PIO=y
CONFIG_8139TOO_TUNE_TWISTER=y
CONFIG_8139TOO_8129=y
# CONFIG_8139_OLD_RX_RESET is not set
CONFIG_SIS900=m
CONFIG_EPIC100=m
CONFIG_SUNDANCE=m
# CONFIG_SUNDANCE_MMIO is not set
CONFIG_TLAN=m
CONFIG_VIA_RHINE=m
# CONFIG_VIA_RHINE_MMIO is not set
CONFIG_VIA_RHINE_NAPI=y
# CONFIG_NET_POCKET is not set

#
# Ethernet (1000 Mbit)
#
CONFIG_ACENIC=m
# CONFIG_ACENIC_OMIT_TIGON_I is not set
CONFIG_DL2K=m
CONFIG_E1000=m
CONFIG_E1000_NAPI=y
# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
CONFIG_NS83820=m
CONFIG_HAMACHI=m
CONFIG_YELLOWFIN=m
CONFIG_R8169=m
CONFIG_R8169_NAPI=y
CONFIG_R8169_VLAN=y
CONFIG_SIS190=m
CONFIG_SKGE=m
CONFIG_SKY2=m
# CONFIG_SK98LIN is not set
CONFIG_VIA_VELOCITY=m
CONFIG_TIGON3=m
CONFIG_BNX2=m

#
# Ethernet (10000 Mbit)
#
CONFIG_CHELSIO_T1=m
CONFIG_IXGB=m
CONFIG_IXGB_NAPI=y
CONFIG_S2IO=m
CONFIG_S2IO_NAPI=y
CONFIG_MYRI10GE=m

#
# Token Ring devices
#
CONFIG_TR=y
CONFIG_IBMTR=m
CONFIG_IBMOL=m
CONFIG_IBMLS=m
CONFIG_TMS380TR=m
CONFIG_TMSPCI=m
CONFIG_SKISA=m
CONFIG_PROTEON=m
CONFIG_ABYSS=m

#
# Wireless LAN (non-hamradio)
#
CONFIG_NET_RADIO=y
CONFIG_NET_WIRELESS_RTNETLINK=y

#
# Obsolete Wireless cards support (pre-802.11)
#
CONFIG_STRIP=m
CONFIG_ARLAN=m
CONFIG_WAVELAN=m
CONFIG_PCMCIA_WAVELAN=m
CONFIG_PCMCIA_NETWAVE=m

#
# Wireless 802.11 Frequency Hopping cards support
#
CONFIG_PCMCIA_RAYCS=m

#
# Wireless 802.11b ISA/PCI cards support
#
CONFIG_IPW2100=m
CONFIG_IPW2100_MONITOR=y
# CONFIG_IPW2100_DEBUG is not set
CONFIG_IPW2200=m
CONFIG_IPW2200_MONITOR=y
# CONFIG_IPW2200_RADIOTAP is not set
# CONFIG_IPW2200_PROMISCUOUS is not set
CONFIG_IPW2200_QOS=y
# CONFIG_IPW2200_DEBUG is not set
CONFIG_AIRO=m
CONFIG_HERMES=m
CONFIG_PLX_HERMES=m
CONFIG_TMD_HERMES=m
CONFIG_NORTEL_HERMES=m
CONFIG_PCI_HERMES=m
CONFIG_ATMEL=m
CONFIG_PCI_ATMEL=m

#
# Wireless 802.11b Pcmcia/Cardbus cards support
#
CONFIG_PCMCIA_HERMES=m
CONFIG_PCMCIA_SPECTRUM=m
CONFIG_AIRO_CS=m
CONFIG_PCMCIA_ATMEL=m
CONFIG_PCMCIA_WL3501=m

#
# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support #
CONFIG_PRISM54=m
CONFIG_USB_ZD1201=m
CONFIG_HOSTAP=m
CONFIG_HOSTAP_FIRMWARE=y
# CONFIG_HOSTAP_FIRMWARE_NVRAM is not set CONFIG_HOSTAP_PLX=m
CONFIG_HOSTAP_PCI=m
CONFIG_HOSTAP_CS=m
CONFIG_BCM43XX=m
CONFIG_BCM43XX_DEBUG=y
CONFIG_BCM43XX_DMA=y
CONFIG_BCM43XX_PIO=y CONFIG_BCM43XX_DMA_AND_PIO_MODE=y
# CONFIG_BCM43XX_DMA_MODE is not set
# CONFIG_BCM43XX_PIO_MODE is not set CONFIG_ZD1211RW=m
# CONFIG_ZD1211RW_DEBUG is not set CONFIG_NET_WIRELESS=y

#
# PCMCIA network device support
#
CONFIG_NET_PCMCIA=y
CONFIG_PCMCIA_3C589=m
CONFIG_PCMCIA_3C574=m
CONFIG_PCMCIA_FMVJ18X=m
CONFIG_PCMCIA_PCNET=m
CONFIG_PCMCIA_NMCLAN=m
CONFIG_PCMCIA_SMC91C92=m
CONFIG_PCMCIA_XIRC2PS=m
CONFIG_PCMCIA_AXNET=m
CONFIG_ARCNET_COM20020_CS=m
CONFIG_PCMCIA_IBMTR=m

#
# Wan interfaces
#
CONFIG_WAN=y
CONFIG_HOSTESS_SV11=m
CONFIG_COSA=m
CONFIG_DSCC4=m
CONFIG_DSCC4_PCISYNC=y
CONFIG_DSCC4_PCI_RST=y
CONFIG_LANMEDIA=m
CONFIG_SEALEVEL_4021=m
CONFIG_HDLC=m
CONFIG_HDLC_RAW=y
CONFIG_HDLC_RAW_ETH=y
CONFIG_HDLC_CISCO=y
CONFIG_HDLC_FR=y
CONFIG_HDLC_PPP=y
CONFIG_HDLC_X25=y
CONFIG_PCI200SYN=m
CONFIG_WANXL=m
CONFIG_PC300=m
CONFIG_PC300_MLPPP=y
CONFIG_N2=m
CONFIG_C101=m
CONFIG_FARSYNC=m
CONFIG_DLCI=m
CONFIG_DLCI_COUNT=24
CONFIG_DLCI_MAX=8
CONFIG_SDLA=m
CONFIG_WAN_ROUTER_DRIVERS=y
CONFIG_CYCLADES_SYNC=m
CONFIG_CYCLOMX_X25=y
CONFIG_LAPBETHER=m
CONFIG_X25_ASY=m
CONFIG_SBNI=m
# CONFIG_SBNI_MULTILINE is not set

#
# ATM drivers
#
CONFIG_ATM_DUMMY=m
CONFIG_ATM_TCP=m
CONFIG_ATM_LANAI=m
CONFIG_ATM_ENI=m
# CONFIG_ATM_ENI_DEBUG is not set
# CONFIG_ATM_ENI_TUNE_BURST is not set
CONFIG_ATM_FIRESTREAM=m
CONFIG_ATM_ZATM=m
# CONFIG_ATM_ZATM_DEBUG is not set
CONFIG_ATM_NICSTAR=m
# CONFIG_ATM_NICSTAR_USE_SUNI is not set
# CONFIG_ATM_NICSTAR_USE_IDT77105 is not set
CONFIG_ATM_IDT77252=m
# CONFIG_ATM_IDT77252_DEBUG is not set
# CONFIG_ATM_IDT77252_RCV_ALL is not set
CONFIG_ATM_IDT77252_USE_SUNI=y
CONFIG_ATM_AMBASSADOR=m
# CONFIG_ATM_AMBASSADOR_DEBUG is not set
CONFIG_ATM_HORIZON=m
# CONFIG_ATM_HORIZON_DEBUG is not set
CONFIG_ATM_IA=m
# CONFIG_ATM_IA_DEBUG is not set
CONFIG_ATM_FORE200E_MAYBE=m
CONFIG_ATM_FORE200E_PCA=y
CONFIG_ATM_FORE200E_PCA_DEFAULT_FW=y
# CONFIG_ATM_FORE200E_USE_TASKLET is not set
CONFIG_ATM_FORE200E_TX_RETRY=16
CONFIG_ATM_FORE200E_DEBUG=0
CONFIG_ATM_FORE200E=m
CONFIG_ATM_HE=m
CONFIG_ATM_HE_USE_SUNI=y
CONFIG_FDDI=y
CONFIG_DEFXX=m
CONFIG_SKFP=m
CONFIG_HIPPI=y
CONFIG_ROADRUNNER=m
# CONFIG_ROADRUNNER_LARGE_RINGS is not set
CONFIG_PLIP=m
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
CONFIG_PPPOATM=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
CONFIG_NET_FC=y
CONFIG_SHAPER=m
CONFIG_NETCONSOLE=m
CONFIG_NETPOLL=y
# CONFIG_NETPOLL_RX is not set
# CONFIG_NETPOLL_TRAP is not set
CONFIG_NET_POLL_CONTROLLER=y

#
# ISDN subsystem
#
CONFIG_ISDN=m

#
# Old ISDN4Linux
#
CONFIG_ISDN_I4L=m
CONFIG_ISDN_PPP=y
CONFIG_ISDN_PPP_VJ=y
CONFIG_ISDN_MPP=y
CONFIG_IPPP_FILTER=y
CONFIG_ISDN_PPP_BSDCOMP=m
CONFIG_ISDN_AUDIO=y
CONFIG_ISDN_TTY_FAX=y
CONFIG_ISDN_X25=y

#
# ISDN feature submodules
#
# CONFIG_ISDN_DIVERSION is not set

#
# ISDN4Linux hardware drivers
#

#
# Passive cards
#
CONFIG_ISDN_DRV_HISAX=m

#
# D-channel protocol features
#
CONFIG_HISAX_EURO=y
CONFIG_DE_AOC=y
# CONFIG_HISAX_NO_SENDCOMPLETE is not set
# CONFIG_HISAX_NO_LLC is not set
# CONFIG_HISAX_NO_KEYPAD is not set
CONFIG_HISAX_1TR6=y
CONFIG_HISAX_NI1=y
CONFIG_HISAX_MAX_CARDS=8

#
# HiSax supported cards
#
CONFIG_HISAX_16_0=y
CONFIG_HISAX_16_3=y
CONFIG_HISAX_TELESPCI=y
CONFIG_HISAX_S0BOX=y
CONFIG_HISAX_AVM_A1=y
CONFIG_HISAX_FRITZPCI=y
CONFIG_HISAX_AVM_A1_PCMCIA=y
CONFIG_HISAX_ELSA=y
CONFIG_HISAX_IX1MICROR2=y
CONFIG_HISAX_DIEHLDIVA=y
CONFIG_HISAX_ASUSCOM=y
CONFIG_HISAX_TELEINT=y
CONFIG_HISAX_HFCS=y
CONFIG_HISAX_SEDLBAUER=y
CONFIG_HISAX_SPORTSTER=y
CONFIG_HISAX_MIC=y
CONFIG_HISAX_NETJET=y
CONFIG_HISAX_NETJET_U=y
CONFIG_HISAX_NICCY=y
CONFIG_HISAX_ISURF=y
CONFIG_HISAX_HSTSAPHIR=y
CONFIG_HISAX_BKM_A4T=y
CONFIG_HISAX_SCT_QUADRO=y
CONFIG_HISAX_GAZEL=y
CONFIG_HISAX_HFC_PCI=y
CONFIG_HISAX_W6692=y
CONFIG_HISAX_HFC_SX=y
CONFIG_HISAX_ENTERNOW_PCI=y
# CONFIG_HISAX_DEBUG is not set

#
# HiSax PCMCIA card service modules
#
CONFIG_HISAX_SEDLBAUER_CS=m
CONFIG_HISAX_ELSA_CS=m
CONFIG_HISAX_AVM_A1_CS=m
CONFIG_HISAX_TELES_CS=m

#
# HiSax sub driver modules
#
CONFIG_HISAX_ST5481=m
CONFIG_HISAX_HFCUSB=m
CONFIG_HISAX_HFC4S8S=m
CONFIG_HISAX_FRITZ_PCIPNP=m
CONFIG_HISAX_HDLC=y

#
# Active cards
#
CONFIG_ISDN_DRV_ICN=m
CONFIG_ISDN_DRV_PCBIT=m
CONFIG_ISDN_DRV_SC=m
CONFIG_ISDN_DRV_ACT2000=m

#
# Siemens Gigaset
#
CONFIG_ISDN_DRV_GIGASET=m
CONFIG_GIGASET_BASE=m
CONFIG_GIGASET_M105=m
# CONFIG_GIGASET_DEBUG is not set
# CONFIG_GIGASET_UNDOCREQ is not set

#
# CAPI subsystem
#
CONFIG_ISDN_CAPI=m
CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON=y
CONFIG_ISDN_CAPI_MIDDLEWARE=y
CONFIG_ISDN_CAPI_CAPI20=m
CONFIG_ISDN_CAPI_CAPIFS_BOOL=y
CONFIG_ISDN_CAPI_CAPIFS=m
CONFIG_ISDN_CAPI_CAPIDRV=m

#
# CAPI hardware drivers
#

#
# Active AVM cards
#
CONFIG_CAPI_AVM=y
CONFIG_ISDN_DRV_AVMB1_B1ISA=m
CONFIG_ISDN_DRV_AVMB1_B1PCI=m
# CONFIG_ISDN_DRV_AVMB1_B1PCIV4 is not set
CONFIG_ISDN_DRV_AVMB1_T1ISA=m
CONFIG_ISDN_DRV_AVMB1_B1PCMCIA=m
# CONFIG_ISDN_DRV_AVMB1_AVM_CS is not set
CONFIG_ISDN_DRV_AVMB1_T1PCI=m
CONFIG_ISDN_DRV_AVMB1_C4=m

#
# Active Eicon DIVA Server cards
#
CONFIG_CAPI_EICON=y
CONFIG_ISDN_DIVAS=m
CONFIG_ISDN_DIVAS_BRIPCI=y
CONFIG_ISDN_DIVAS_PRIPCI=y
CONFIG_ISDN_DIVAS_DIVACAPI=m
CONFIG_ISDN_DIVAS_USERIDI=m
CONFIG_ISDN_DIVAS_MAINT=m

#
# Telephony Support
#
CONFIG_PHONE=m
CONFIG_PHONE_IXJ=m
CONFIG_PHONE_IXJ_PCMCIA=m

#
# Input device support
#
CONFIG_INPUT=y

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=m
CONFIG_INPUT_TSDEV=m
CONFIG_INPUT_TSDEV_SCREEN_X=240
CONFIG_INPUT_TSDEV_SCREEN_Y=320
CONFIG_INPUT_EVDEV=m
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
CONFIG_KEYBOARD_SUNKBD=m
CONFIG_KEYBOARD_LKKBD=m
CONFIG_KEYBOARD_XTKBD=m
CONFIG_KEYBOARD_NEWTON=m
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=m
CONFIG_MOUSE_SERIAL=m
CONFIG_MOUSE_INPORT=m
# CONFIG_MOUSE_ATIXL is not set
CONFIG_MOUSE_LOGIBM=m
CONFIG_MOUSE_PC110PAD=m
CONFIG_MOUSE_VSXXXAA=m
CONFIG_INPUT_JOYSTICK=y
CONFIG_JOYSTICK_ANALOG=m
CONFIG_JOYSTICK_A3D=m
CONFIG_JOYSTICK_ADI=m
CONFIG_JOYSTICK_COBRA=m
CONFIG_JOYSTICK_GF2K=m
CONFIG_JOYSTICK_GRIP=m
CONFIG_JOYSTICK_GRIP_MP=m
CONFIG_JOYSTICK_GUILLEMOT=m
CONFIG_JOYSTICK_INTERACT=m
CONFIG_JOYSTICK_SIDEWINDER=m
CONFIG_JOYSTICK_TMDC=m
CONFIG_JOYSTICK_IFORCE=m
CONFIG_JOYSTICK_IFORCE_USB=y
CONFIG_JOYSTICK_IFORCE_232=y
CONFIG_JOYSTICK_WARRIOR=m
CONFIG_JOYSTICK_MAGELLAN=m
CONFIG_JOYSTICK_SPACEORB=m
CONFIG_JOYSTICK_SPACEBALL=m
CONFIG_JOYSTICK_STINGER=m
CONFIG_JOYSTICK_TWIDJOY=m
CONFIG_JOYSTICK_DB9=m
CONFIG_JOYSTICK_GAMECON=m
CONFIG_JOYSTICK_TURBOGRAFX=m
CONFIG_JOYSTICK_JOYDUMP=m
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ADS7846=m
CONFIG_TOUCHSCREEN_GUNZE=m
CONFIG_TOUCHSCREEN_ELO=m
CONFIG_TOUCHSCREEN_MTOUCH=m
CONFIG_TOUCHSCREEN_MK712=m
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
CONFIG_INPUT_WISTRON_BTNS=m
CONFIG_INPUT_UINPUT=m

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=m
CONFIG_SERIO_CT82C710=m
CONFIG_SERIO_PARKBD=m
CONFIG_SERIO_PCIPS2=m
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=m
CONFIG_GAMEPORT=m
CONFIG_GAMEPORT_NS558=m
CONFIG_GAMEPORT_L4=m
CONFIG_GAMEPORT_EMU10K1=m
CONFIG_GAMEPORT_FM801=m

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
CONFIG_ROCKETPORT=m
CONFIG_CYCLADES=m
# CONFIG_CYZ_INTR is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_ESPSERIAL is not set
# CONFIG_MOXA_INTELLIO is not set
CONFIG_MOXA_SMARTIO=m
# CONFIG_ISI is not set
CONFIG_SYNCLINK=m
CONFIG_SYNCLINKMP=m
CONFIG_SYNCLINK_GT=m
CONFIG_N_HDLC=m
# CONFIG_SPECIALIX is not set
CONFIG_SX=m
# CONFIG_RIO is not set
CONFIG_STALDRV=y

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_PNP=y
CONFIG_SERIAL_8250_CS=m
CONFIG_SERIAL_8250_NR_UARTS=16
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
CONFIG_SERIAL_8250_RSA=y
CONFIG_SERIAL_8250_FOURPORT=m
CONFIG_SERIAL_8250_ACCENT=m
CONFIG_SERIAL_8250_BOCA=m
CONFIG_SERIAL_8250_HUB6=m

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_JSM=m
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=16
CONFIG_PRINTER=m
# CONFIG_LP_CONSOLE is not set
CONFIG_PPDEV=m
CONFIG_TIPAR=m

#
# IPMI
#
CONFIG_IPMI_HANDLER=m
# CONFIG_IPMI_PANIC_EVENT is not set
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_SI=m
CONFIG_IPMI_WATCHDOG=m
CONFIG_IPMI_POWEROFF=m

#
# Watchdog Cards
#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set

#
# Watchdog Device Drivers
#
CONFIG_SOFT_WATCHDOG=m
CONFIG_ACQUIRE_WDT=m
CONFIG_ADVANTECH_WDT=m
CONFIG_ALIM1535_WDT=m
CONFIG_ALIM7101_WDT=m
CONFIG_SC520_WDT=m
CONFIG_EUROTECH_WDT=m
CONFIG_IB700_WDT=m
CONFIG_IBMASR=m
CONFIG_WAFER_WDT=m
CONFIG_I6300ESB_WDT=m
CONFIG_I8XX_TCO=m
CONFIG_SC1200_WDT=m
CONFIG_SCx200_WDT=m
CONFIG_60XX_WDT=m
CONFIG_SBC8360_WDT=m
CONFIG_CPU5_WDT=m
CONFIG_W83627HF_WDT=m
CONFIG_W83877F_WDT=m
CONFIG_W83977F_WDT=m
CONFIG_MACHZ_WDT=m
CONFIG_SBC_EPX_C3_WATCHDOG=m

#
# ISA-based Watchdog Cards
#
CONFIG_PCWATCHDOG=m
CONFIG_MIXCOMWD=m
CONFIG_WDT=m
CONFIG_WDT_501=y

#
# PCI-based Watchdog Cards
#
CONFIG_PCIPCWATCHDOG=m
CONFIG_WDTPCI=m
CONFIG_WDT_501_PCI=y

#
# USB-based Watchdog Cards
#
CONFIG_USBPCWATCHDOG=m
CONFIG_HW_RANDOM=y
CONFIG_HW_RANDOM_INTEL=m
CONFIG_HW_RANDOM_AMD=m
CONFIG_HW_RANDOM_GEODE=m
CONFIG_HW_RANDOM_VIA=m
CONFIG_NVRAM=m
CONFIG_RTC=m
CONFIG_GEN_RTC=m
CONFIG_GEN_RTC_X=y
CONFIG_DTLK=m
CONFIG_R3964=m
CONFIG_APPLICOM=m
CONFIG_SONYPI=m

#
# Ftape, the floppy tape device driver
#
CONFIG_AGP=m
CONFIG_AGP_ALI=m
CONFIG_AGP_ATI=m
CONFIG_AGP_AMD=m
CONFIG_AGP_AMD64=m
CONFIG_AGP_INTEL=m
CONFIG_AGP_NVIDIA=m
CONFIG_AGP_SIS=m
CONFIG_AGP_SWORKS=m
CONFIG_AGP_VIA=m
CONFIG_AGP_EFFICEON=m
CONFIG_DRM=m
CONFIG_DRM_TDFX=m
CONFIG_DRM_R128=m
CONFIG_DRM_RADEON=m
CONFIG_DRM_I810=m
CONFIG_DRM_I830=m
CONFIG_DRM_I915=m
CONFIG_DRM_MGA=m
CONFIG_DRM_SIS=m
CONFIG_DRM_VIA=m
CONFIG_DRM_SAVAGE=m

#
# PCMCIA character devices
#
CONFIG_SYNCLINK_CS=m
CONFIG_CARDMAN_4000=m
CONFIG_CARDMAN_4040=m
CONFIG_MWAVE=m
CONFIG_SCx200_GPIO=m
CONFIG_PC8736x_GPIO=m
CONFIG_NSC_GPIO=m
CONFIG_CS5535_GPIO=m
CONFIG_RAW_DRIVER=m
CONFIG_MAX_RAW_DEVS=256
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
CONFIG_HANGCHECK_TIMER=m

#
# TPM devices
#
# CONFIG_TCG_TPM is not set
CONFIG_TELCLOCK=m

#
# I2C support
#
CONFIG_I2C=m
CONFIG_I2C_CHARDEV=m

#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_ALGOPCF=m
CONFIG_I2C_ALGOPCA=m

#
# I2C Hardware Bus support
#
CONFIG_I2C_ALI1535=m
CONFIG_I2C_ALI1563=m
CONFIG_I2C_ALI15X3=m
CONFIG_I2C_AMD756=m
CONFIG_I2C_AMD756_S4882=m
CONFIG_I2C_AMD8111=m
# CONFIG_I2C_ELEKTOR is not set
CONFIG_I2C_I801=m
CONFIG_I2C_I810=m
CONFIG_I2C_PIIX4=m
CONFIG_I2C_ISA=m
CONFIG_I2C_NFORCE2=m
CONFIG_I2C_OCORES=m
CONFIG_I2C_PARPORT=m
CONFIG_I2C_PARPORT_LIGHT=m
CONFIG_I2C_PROSAVAGE=m
CONFIG_I2C_SAVAGE4=m
CONFIG_SCx200_I2C=m
CONFIG_SCx200_I2C_SCL=12
CONFIG_SCx200_I2C_SDA=13
CONFIG_SCx200_ACB=m
CONFIG_I2C_SIS5595=m
CONFIG_I2C_SIS630=m
CONFIG_I2C_SIS96X=m
CONFIG_I2C_STUB=m
CONFIG_I2C_VIA=m
CONFIG_I2C_VIAPRO=m
CONFIG_I2C_VOODOO3=m
CONFIG_I2C_PCA_ISA=m

#
# Miscellaneous I2C Chip support
#
CONFIG_SENSORS_DS1337=m
CONFIG_SENSORS_DS1374=m
CONFIG_SENSORS_EEPROM=m
CONFIG_SENSORS_PCF8574=m
CONFIG_SENSORS_PCA9539=m
CONFIG_SENSORS_PCF8591=m
CONFIG_SENSORS_MAX6875=m
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set

#
# SPI support
#
CONFIG_SPI=y
CONFIG_SPI_MASTER=y

#
# SPI Master Controller Drivers
#
CONFIG_SPI_BITBANG=m
CONFIG_SPI_BUTTERFLY=m

#
# SPI Protocol Masters
#

#
# Dallas's 1-wire bus
#
CONFIG_W1=m
CONFIG_W1_CON=y

#
# 1-wire Bus Masters
#
CONFIG_W1_MASTER_MATROX=m
CONFIG_W1_MASTER_DS2490=m
CONFIG_W1_MASTER_DS2482=m

#
# 1-wire Slaves
#
CONFIG_W1_SLAVE_THERM=m
CONFIG_W1_SLAVE_SMEM=m
CONFIG_W1_SLAVE_DS2433=m
# CONFIG_W1_SLAVE_DS2433_CRC is not set

#
# Hardware Monitoring support
#
CONFIG_HWMON=y
CONFIG_HWMON_VID=m
CONFIG_SENSORS_ABITUGURU=m
CONFIG_SENSORS_ADM1021=m
CONFIG_SENSORS_ADM1025=m
CONFIG_SENSORS_ADM1026=m
CONFIG_SENSORS_ADM1031=m
CONFIG_SENSORS_ADM9240=m
CONFIG_SENSORS_ASB100=m
CONFIG_SENSORS_ATXP1=m
CONFIG_SENSORS_DS1621=m
CONFIG_SENSORS_F71805F=m
# CONFIG_SENSORS_F75375S is not set
CONFIG_SENSORS_FSCHER=m
CONFIG_SENSORS_FSCPOS=m
CONFIG_SENSORS_GL518SM=m
CONFIG_SENSORS_GL520SM=m
CONFIG_SENSORS_IT87=m
CONFIG_SENSORS_LM63=m
CONFIG_SENSORS_LM70=m
CONFIG_SENSORS_LM75=m
CONFIG_SENSORS_LM77=m
CONFIG_SENSORS_LM78=m
CONFIG_SENSORS_LM80=m
CONFIG_SENSORS_LM83=m
CONFIG_SENSORS_LM85=m
CONFIG_SENSORS_LM87=m
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_LM92=m
CONFIG_SENSORS_MAX1619=m
CONFIG_SENSORS_PC87360=m
CONFIG_SENSORS_SIS5595=m
CONFIG_SENSORS_SMSC47M1=m
CONFIG_SENSORS_SMSC47M192=m
CONFIG_SENSORS_SMSC47B397=m
CONFIG_SENSORS_VIA686A=m
CONFIG_SENSORS_VT8231=m
CONFIG_SENSORS_W83781D=m
CONFIG_SENSORS_W83791D=m
CONFIG_SENSORS_W83792D=m
CONFIG_SENSORS_W83793=m
CONFIG_SENSORS_W83L785TS=m
CONFIG_SENSORS_W83627HF=m
CONFIG_SENSORS_W83627EHF=m
CONFIG_SENSORS_HDAPS=m
# CONFIG_HWMON_DEBUG_CHIP is not set

#
# Misc devices
#
CONFIG_IBM_ASM=m

#
# Multimedia devices
#
CONFIG_VIDEO_DEV=m
CONFIG_VIDEO_V4L1=y
CONFIG_VIDEO_V4L1_COMPAT=y
CONFIG_VIDEO_V4L2=y

#
# Video Capture Adapters
#

#
# Video Capture Adapters
#
# CONFIG_VIDEO_ADV_DEBUG is not set
CONFIG_VIDEO_VIVI=m
CONFIG_VIDEO_BT848=m
CONFIG_VIDEO_BT848_DVB=y
CONFIG_VIDEO_SAA6588=m
CONFIG_VIDEO_PMS=m
CONFIG_VIDEO_BWQCAM=m
CONFIG_VIDEO_CQCAM=m
CONFIG_VIDEO_W9966=m
CONFIG_VIDEO_CPIA=m
CONFIG_VIDEO_CPIA_PP=m
CONFIG_VIDEO_CPIA_USB=m
CONFIG_VIDEO_CPIA2=m
CONFIG_VIDEO_SAA5246A=m
CONFIG_VIDEO_SAA5249=m
CONFIG_TUNER_3036=m
CONFIG_VIDEO_STRADIS=m
CONFIG_VIDEO_ZORAN=m
CONFIG_VIDEO_ZORAN_BUZ=m
CONFIG_VIDEO_ZORAN_DC10=m
CONFIG_VIDEO_ZORAN_DC30=m
CONFIG_VIDEO_ZORAN_LML33=m
CONFIG_VIDEO_ZORAN_LML33R10=m
CONFIG_VIDEO_ZORAN_AVS6EYES=m
CONFIG_VIDEO_MEYE=m
CONFIG_VIDEO_SAA7134=m
CONFIG_VIDEO_SAA7134_ALSA=m
CONFIG_VIDEO_SAA7134_OSS=m
CONFIG_VIDEO_SAA7134_DVB=m
CONFIG_VIDEO_SAA7134_DVB_ALL_FRONTENDS=y
CONFIG_VIDEO_MXB=m
CONFIG_VIDEO_DPC=m
CONFIG_VIDEO_HEXIUM_ORION=m
CONFIG_VIDEO_HEXIUM_GEMINI=m
CONFIG_VIDEO_CX88_VP3054=m
CONFIG_VIDEO_CX88=m
CONFIG_VIDEO_CX88_ALSA=m
CONFIG_VIDEO_CX88_BLACKBIRD=m
CONFIG_VIDEO_CX88_DVB=m
CONFIG_VIDEO_CX88_DVB_ALL_FRONTENDS=y

#
# Encoders and Decoders
#
CONFIG_VIDEO_MSP3400=m
CONFIG_VIDEO_CS53L32A=m
CONFIG_VIDEO_TLV320AIC23B=m
CONFIG_VIDEO_WM8775=m
CONFIG_VIDEO_WM8739=m
CONFIG_VIDEO_CX2341X=m
CONFIG_VIDEO_CX25840=m
CONFIG_VIDEO_SAA711X=m
CONFIG_VIDEO_SAA7127=m
CONFIG_VIDEO_UPD64031A=m
CONFIG_VIDEO_UPD64083=m

#
# V4L USB devices
#
CONFIG_VIDEO_PVRUSB2=m
CONFIG_VIDEO_PVRUSB2_24XXX=y
CONFIG_VIDEO_PVRUSB2_SYSFS=y
# CONFIG_VIDEO_PVRUSB2_DEBUGIFC is not set
CONFIG_VIDEO_EM28XX=m
CONFIG_VIDEO_USBVIDEO=m
CONFIG_USB_VICAM=m
CONFIG_USB_IBMCAM=m
CONFIG_USB_KONICAWC=m
CONFIG_USB_QUICKCAM_MESSENGER=m
CONFIG_USB_ET61X251=m
CONFIG_VIDEO_OVCAMCHIP=m
# CONFIG_USB_W9968CF is not set
CONFIG_USB_OV511=m
CONFIG_USB_SE401=m
CONFIG_USB_SN9C102=m
CONFIG_USB_STV680=m
CONFIG_USB_ZC0301=m
CONFIG_USB_PWC=m
# CONFIG_USB_PWC_DEBUG is not set

#
# Radio Adapters
#
CONFIG_RADIO_CADET=m
CONFIG_RADIO_RTRACK=m
CONFIG_RADIO_RTRACK2=m
CONFIG_RADIO_AZTECH=m
CONFIG_RADIO_GEMTEK=m
CONFIG_RADIO_GEMTEK_PCI=m
CONFIG_RADIO_MAXIRADIO=m
CONFIG_RADIO_MAESTRO=m
CONFIG_RADIO_SF16FMI=m
CONFIG_RADIO_SF16FMR2=m
CONFIG_RADIO_TERRATEC=m
CONFIG_RADIO_TRUST=m
CONFIG_RADIO_TYPHOON=m
CONFIG_RADIO_TYPHOON_PROC_FS=y
CONFIG_RADIO_ZOLTRIX=m
CONFIG_USB_DSBR=m

#
# Digital Video Broadcasting Devices
#
CONFIG_DVB=y
CONFIG_DVB_CORE=m

#
# Supported SAA7146 based PCI Adapters
#
CONFIG_DVB_AV7110=m
CONFIG_DVB_AV7110_OSD=y
CONFIG_DVB_BUDGET=m
CONFIG_DVB_BUDGET_CI=m
CONFIG_DVB_BUDGET_AV=m
CONFIG_DVB_BUDGET_PATCH=m

#
# Supported USB Adapters
#
CONFIG_DVB_USB=m
# CONFIG_DVB_USB_DEBUG is not set
CONFIG_DVB_USB_A800=m
CONFIG_DVB_USB_DIBUSB_MB=m
CONFIG_DVB_USB_DIBUSB_MB_FAULTY=y
CONFIG_DVB_USB_DIBUSB_MC=m
CONFIG_DVB_USB_UMT_010=m
CONFIG_DVB_USB_CXUSB=m
CONFIG_DVB_USB_DIGITV=m
CONFIG_DVB_USB_VP7045=m
CONFIG_DVB_USB_VP702X=m
CONFIG_DVB_USB_GP8PSK=m
CONFIG_DVB_USB_NOVA_T_USB2=m
CONFIG_DVB_USB_DTT200U=m
CONFIG_DVB_TTUSB_BUDGET=m
CONFIG_DVB_TTUSB_DEC=m
CONFIG_DVB_CINERGYT2=m
# CONFIG_DVB_CINERGYT2_TUNING is not set

#
# Supported FlexCopII (B2C2) Adapters
#
CONFIG_DVB_B2C2_FLEXCOP=m
CONFIG_DVB_B2C2_FLEXCOP_PCI=m
CONFIG_DVB_B2C2_FLEXCOP_USB=m
# CONFIG_DVB_B2C2_FLEXCOP_DEBUG is not set

#
# Supported BT878 Adapters
#
CONFIG_DVB_BT8XX=m

#
# Supported Pluto2 Adapters
#
CONFIG_DVB_PLUTO2=m

#
# Supported DVB Frontends
#

#
# Customise DVB Frontends
#

#
# DVB-S (satellite) frontends
#
CONFIG_DVB_STV0299=m
CONFIG_DVB_CX24110=m
CONFIG_DVB_CX24123=m
CONFIG_DVB_TDA8083=m
CONFIG_DVB_MT312=m
CONFIG_DVB_VES1X93=m
CONFIG_DVB_S5H1420=m

#
# DVB-T (terrestrial) frontends
#
CONFIG_DVB_SP8870=m
CONFIG_DVB_SP887X=m
CONFIG_DVB_CX22700=m
CONFIG_DVB_CX22702=m
CONFIG_DVB_L64781=m
CONFIG_DVB_TDA1004X=m
CONFIG_DVB_NXT6000=m
CONFIG_DVB_MT352=m
CONFIG_DVB_ZL10353=m
CONFIG_DVB_DIB3000MB=m
CONFIG_DVB_DIB3000MC=m

#
# DVB-C (cable) frontends
#
CONFIG_DVB_VES1820=m
CONFIG_DVB_TDA10021=m
CONFIG_DVB_STV0297=m

#
# ATSC (North American/Korean Terrestrial/Cable DTV) frontends #
CONFIG_DVB_NXT200X=m
CONFIG_DVB_OR51211=m
CONFIG_DVB_OR51132=m
CONFIG_DVB_BCM3510=m
CONFIG_DVB_LGDT330X=m

#
# Miscellaneous devices
#
CONFIG_DVB_PLL=m
CONFIG_DVB_LNBP21=m
CONFIG_DVB_ISL6421=m
CONFIG_VIDEO_SAA7146=m
CONFIG_VIDEO_SAA7146_VV=m
CONFIG_VIDEO_VIDEOBUF=m
CONFIG_VIDEO_TUNER=m
CONFIG_VIDEO_BUF=m
CONFIG_VIDEO_BUF_DVB=m
CONFIG_VIDEO_BTCX=m
CONFIG_VIDEO_IR=m
CONFIG_VIDEO_TVEEPROM=m

#
# Graphics support
#
CONFIG_FIRMWARE_EDID=y
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
CONFIG_FB_CIRRUS=m
CONFIG_FB_PM2=m
CONFIG_FB_PM2_FIFO_DISCONNECT=y
CONFIG_FB_CYBER2000=m
CONFIG_FB_ARC=m
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
CONFIG_FB_VGA16=m
CONFIG_FB_VESA=y
# CONFIG_FB_IMAC is not set
CONFIG_FB_HGA=m
# CONFIG_FB_HGA_ACCEL is not set
CONFIG_FB_S1D13XXX=m
CONFIG_FB_NVIDIA=m
CONFIG_FB_NVIDIA_I2C=y
# CONFIG_FB_RIVA is not set
CONFIG_FB_I810=m
# CONFIG_FB_I810_GTF is not set
CONFIG_FB_INTEL=m
# CONFIG_FB_INTEL_DEBUG is not set
CONFIG_FB_MATROX=m
CONFIG_FB_MATROX_MILLENIUM=y
CONFIG_FB_MATROX_MYSTIQUE=y
CONFIG_FB_MATROX_G=y
CONFIG_FB_MATROX_I2C=m
CONFIG_FB_MATROX_MAVEN=m
CONFIG_FB_MATROX_MULTIHEAD=y
CONFIG_FB_RADEON=m
CONFIG_FB_RADEON_I2C=y
# CONFIG_FB_RADEON_DEBUG is not set
CONFIG_FB_ATY128=m
CONFIG_FB_ATY=m
CONFIG_FB_ATY_CT=y
CONFIG_FB_ATY_GENERIC_LCD=y
CONFIG_FB_ATY_GX=y
CONFIG_FB_SAVAGE=m
CONFIG_FB_SAVAGE_I2C=y
# CONFIG_FB_SAVAGE_ACCEL is not set
CONFIG_FB_SIS=m
CONFIG_FB_SIS_300=y
CONFIG_FB_SIS_315=y
CONFIG_FB_NEOMAGIC=m
CONFIG_FB_KYRO=m
CONFIG_FB_3DFX=m
# CONFIG_FB_3DFX_ACCEL is not set
CONFIG_FB_VOODOO1=m
CONFIG_FB_CYBLA=m
CONFIG_FB_TRIDENT=m
# CONFIG_FB_TRIDENT_ACCEL is not set
CONFIG_FB_GEODE=y
CONFIG_FB_GEODE_GX=m
CONFIG_FB_GEODE_GX1=m
CONFIG_FB_VIRTUAL=m

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VGACON_SOFT_SCROLLBACK is not set
CONFIG_VIDEO_SELECT=y
CONFIG_MDA_CONSOLE=m
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y

#
# Logo configuration
#
# CONFIG_LOGO is not set
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_BACKLIGHT_CLASS_DEVICE=m
CONFIG_BACKLIGHT_DEVICE=y
# CONFIG_LCD_CLASS_DEVICE is not set

#
# Sound
#
CONFIG_SOUND=m

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
# CONFIG_SND_DYNAMIC_MINORS is not set
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set

#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
CONFIG_SND_OPL3_LIB=m
CONFIG_SND_OPL4_LIB=m
CONFIG_SND_VX_LIB=m
CONFIG_SND_AC97_CODEC=m
CONFIG_SND_AC97_BUS=m
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
CONFIG_SND_MTPAV=m
CONFIG_SND_SERIAL_U16550=m
CONFIG_SND_MPU401=m

#
# ISA devices
#
CONFIG_SND_AD1848_LIB=m
CONFIG_SND_CS4231_LIB=m
CONFIG_SND_ADLIB=m
CONFIG_SND_AD1816A=m
CONFIG_SND_AD1848=m
CONFIG_SND_ALS100=m
CONFIG_SND_AZT2320=m
CONFIG_SND_CMI8330=m
CONFIG_SND_CS4231=m
CONFIG_SND_CS4232=m
CONFIG_SND_CS4236=m
CONFIG_SND_DT019X=m
CONFIG_SND_ES968=m
CONFIG_SND_ES1688=m
CONFIG_SND_ES18XX=m
CONFIG_SND_GUS_SYNTH=m
CONFIG_SND_GUSCLASSIC=m
CONFIG_SND_GUSEXTREME=m
CONFIG_SND_GUSMAX=m
CONFIG_SND_INTERWAVE=m
CONFIG_SND_INTERWAVE_STB=m
CONFIG_SND_OPL3SA2=m
CONFIG_SND_OPTI92X_AD1848=m
CONFIG_SND_OPTI92X_CS4231=m
CONFIG_SND_OPTI93X=m
CONFIG_SND_MIRO=m
CONFIG_SND_SB8=m
CONFIG_SND_SB16=m
CONFIG_SND_SBAWE=m
CONFIG_SND_SB16_CSP=y
CONFIG_SND_SGALAXY=m
CONFIG_SND_SSCAPE=m
CONFIG_SND_WAVEFRONT=m

#
# PCI devices
#
CONFIG_SND_AD1889=m
CONFIG_SND_ALS300=m
CONFIG_SND_ALS4000=m
CONFIG_SND_ALI5451=m
CONFIG_SND_ATIIXP=m
CONFIG_SND_ATIIXP_MODEM=m
CONFIG_SND_AU8810=m
CONFIG_SND_AU8820=m
CONFIG_SND_AU8830=m
CONFIG_SND_AZT3328=m
CONFIG_SND_BT87X=m
# CONFIG_SND_BT87X_OVERCLOCK is not set
CONFIG_SND_CA0106=m
CONFIG_SND_CMIPCI=m
CONFIG_SND_CS4281=m
CONFIG_SND_CS46XX=m
CONFIG_SND_CS46XX_NEW_DSP=y
CONFIG_SND_CS5535AUDIO=m
CONFIG_SND_DARLA20=m
CONFIG_SND_GINA20=m
CONFIG_SND_LAYLA20=m
CONFIG_SND_DARLA24=m
CONFIG_SND_GINA24=m
CONFIG_SND_LAYLA24=m
CONFIG_SND_MONA=m
CONFIG_SND_MIA=m
CONFIG_SND_ECHO3G=m
CONFIG_SND_INDIGO=m
CONFIG_SND_INDIGOIO=m
CONFIG_SND_INDIGODJ=m
CONFIG_SND_EMU10K1=m
CONFIG_SND_EMU10K1X=m
CONFIG_SND_ENS1370=m
CONFIG_SND_ENS1371=m
CONFIG_SND_ES1938=m
CONFIG_SND_ES1968=m
CONFIG_SND_FM801=m
CONFIG_SND_FM801_TEA575X_BOOL=y
CONFIG_SND_FM801_TEA575X=m
CONFIG_SND_HDA_INTEL=m
CONFIG_SND_HDSP=m
CONFIG_SND_HDSPM=m
CONFIG_SND_ICE1712=m
CONFIG_SND_ICE1724=m
CONFIG_SND_INTEL8X0=m
CONFIG_SND_INTEL8X0M=m
CONFIG_SND_KORG1212=m
CONFIG_SND_MAESTRO3=m
CONFIG_SND_MIXART=m
CONFIG_SND_NM256=m
CONFIG_SND_PCXHR=m
CONFIG_SND_RIPTIDE=m
CONFIG_SND_RME32=m
CONFIG_SND_RME96=m
CONFIG_SND_RME9652=m
CONFIG_SND_SONICVIBES=m
CONFIG_SND_TRIDENT=m
CONFIG_SND_VIA82XX=m
CONFIG_SND_VIA82XX_MODEM=m
CONFIG_SND_VX222=m
CONFIG_SND_YMFPCI=m

#
# USB devices
#
CONFIG_SND_USB_AUDIO=m
CONFIG_SND_USB_USX2Y=m

#
# PCMCIA devices
#
CONFIG_SND_VXPOCKET=m
CONFIG_SND_PDAUDIOCF=m

#
# Open Sound System
#
CONFIG_SOUND_PRIME=m
# CONFIG_OSS_OBSOLETE_DRIVER is not set
CONFIG_SOUND_BT878=m
CONFIG_SOUND_ES1371=m
CONFIG_SOUND_ICH=m
CONFIG_SOUND_TRIDENT=m
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
CONFIG_SOUND_VIA82CXXX=m
CONFIG_MIDI_VIA82CXXX=y
CONFIG_SOUND_OSS=m
# CONFIG_SOUND_TRACEINIT is not set
# CONFIG_SOUND_DMAP is not set
CONFIG_SOUND_CS4232=m
CONFIG_SOUND_SSCAPE=m
CONFIG_SOUND_VMIDI=m
CONFIG_SOUND_TRIX=m
CONFIG_SOUND_MSS=m
CONFIG_SOUND_MPU401=m
CONFIG_SOUND_PAS=m
CONFIG_SOUND_PSS=m
CONFIG_PSS_MIXER=y
CONFIG_SOUND_SB=m
CONFIG_SOUND_YM3812=m
CONFIG_SOUND_UART6850=m
CONFIG_SOUND_AEDSP16=m
CONFIG_SC6600=y
CONFIG_SC6600_JOY=y
CONFIG_SC6600_CDROM=4
CONFIG_SC6600_CDROMBASE=0x0
# CONFIG_AEDSP16_MSS is not set
# CONFIG_AEDSP16_SBPRO is not set
# CONFIG_AEDSP16_MPU401 is not set
CONFIG_SOUND_TVMIXER=m
CONFIG_SOUND_KAHLUA=m

#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
CONFIG_USB_SUSPEND=y
# CONFIG_USB_OTG is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
CONFIG_USB_ISP116X_HCD=m
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
CONFIG_USB_SL811_HCD=m
CONFIG_USB_SL811_CS=m

#
# USB Device Class drivers
#
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m

#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' #

# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
CONFIG_USB_STORAGE_ALAUDA=y
# CONFIG_USB_LIBUSUAL is not set

#
# USB Input Devices
#
CONFIG_USB_HID=m
CONFIG_USB_HIDINPUT=y
CONFIG_USB_HIDINPUT_POWERBOOK=y
# CONFIG_HID_FF is not set
CONFIG_USB_HIDDEV=y

#
# USB HID Boot Protocol drivers
#
CONFIG_USB_KBD=m
CONFIG_USB_MOUSE=m
CONFIG_USB_AIPTEK=m
CONFIG_USB_WACOM=m
CONFIG_USB_ACECAD=m
CONFIG_USB_KBTAB=m
CONFIG_USB_POWERMATE=m
CONFIG_USB_TOUCHSCREEN=m
CONFIG_USB_TOUCHSCREEN_EGALAX=y
CONFIG_USB_TOUCHSCREEN_PANJIT=y
CONFIG_USB_TOUCHSCREEN_3M=y
CONFIG_USB_TOUCHSCREEN_ITM=y
CONFIG_USB_YEALINK=m
CONFIG_USB_XPAD=m
CONFIG_USB_ATI_REMOTE=m
CONFIG_USB_ATI_REMOTE2=m
CONFIG_USB_KEYSPAN_REMOTE=m
CONFIG_USB_APPLETOUCH=m

#
# USB Imaging devices
#
CONFIG_USB_MDC800=m
CONFIG_USB_MICROTEK=m

#
# USB Network Adapters
#
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
CONFIG_USB_NET_GL620A=m
CONFIG_USB_NET_NET1080=m
CONFIG_USB_NET_PLUSB=m
CONFIG_USB_NET_RNDIS_HOST=m
CONFIG_USB_NET_CDC_SUBSET=m
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_BELKIN=y
CONFIG_USB_ARMLINUX=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_NET_ZAURUS=m
CONFIG_USB_MON=y

#
# USB port drivers
#
CONFIG_USB_USS720=m

#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_AIRPRIME=m
CONFIG_USB_SERIAL_ARK3116=m
CONFIG_USB_SERIAL_BELKIN=m
# CONFIG_USB_SERIAL_WHITEHEAT is not set
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
CONFIG_USB_SERIAL_CP2101=m
CONFIG_USB_SERIAL_CYPRESS_M8=m
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_FUNSOFT=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
CONFIG_USB_SERIAL_IR=m
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
CONFIG_USB_SERIAL_GARMIN=m
CONFIG_USB_SERIAL_IPW=m
CONFIG_USB_SERIAL_KEYSPAN_PDA=m
CONFIG_USB_SERIAL_KLSI=m
CONFIG_USB_SERIAL_KOBIL_SCT=m
CONFIG_USB_SERIAL_MCT_U232=m
CONFIG_USB_SERIAL_NAVMAN=m
CONFIG_USB_SERIAL_PL2303=m
CONFIG_USB_SERIAL_HP4X=m
CONFIG_USB_SERIAL_SAFE=m
# CONFIG_USB_SERIAL_SAFE_PADDED is not set
CONFIG_USB_SERIAL_SIERRAWIRELESS=m
CONFIG_USB_SERIAL_TI=m
CONFIG_USB_SERIAL_CYBERJACK=m
CONFIG_USB_SERIAL_XIRCOM=m
CONFIG_USB_SERIAL_OPTION=m
CONFIG_USB_SERIAL_OMNINET=m
CONFIG_USB_EZUSB=y

#
# USB Miscellaneous drivers
#
CONFIG_USB_AUERSWALD=m
CONFIG_USB_RIO500=m
CONFIG_USB_LEGOTOWER=m
CONFIG_USB_LCD=m
CONFIG_USB_LED=m
CONFIG_USB_CYPRESS_CY7C63=m
CONFIG_USB_CYTHERM=m
CONFIG_USB_PHIDGETKIT=m
CONFIG_USB_PHIDGETSERVO=m
CONFIG_USB_IDMOUSE=m
CONFIG_USB_APPLEDISPLAY=m
CONFIG_USB_SISUSBVGA=m
CONFIG_USB_SISUSBVGA_CON=y
CONFIG_USB_LD=m
CONFIG_USB_TEST=m

#
# USB DSL modem support
#
CONFIG_USB_ATM=m
CONFIG_USB_SPEEDTOUCH=m
CONFIG_USB_CXACRU=m
CONFIG_USB_UEAGLEATM=m
CONFIG_USB_XUSBATM=m

#
# USB Gadget Support
#
CONFIG_USB_GADGET=m
# CONFIG_USB_GADGET_DEBUG_FILES is not set
CONFIG_USB_GADGET_SELECTED=y
CONFIG_USB_GADGET_NET2280=y
CONFIG_USB_NET2280=m
# CONFIG_USB_GADGET_PXA2XX is not set
# CONFIG_USB_GADGET_GOKU is not set
# CONFIG_USB_GADGET_LH7A40X is not set
# CONFIG_USB_GADGET_OMAP is not set
# CONFIG_USB_GADGET_AT91 is not set
# CONFIG_USB_GADGET_DUMMY_HCD is not set
CONFIG_USB_GADGET_DUALSPEED=y
CONFIG_USB_ZERO=m
CONFIG_USB_ETH=m
CONFIG_USB_ETH_RNDIS=y
CONFIG_USB_GADGETFS=m
CONFIG_USB_FILE_STORAGE=m
# CONFIG_USB_FILE_STORAGE_TEST is not set
CONFIG_USB_G_SERIAL=m

#
# MMC/SD Card support
#
CONFIG_MMC=m
# CONFIG_MMC_DEBUG is not set
CONFIG_MMC_BLOCK=m
CONFIG_MMC_SDHCI=m
CONFIG_MMC_WBSD=m

#
# LED devices
#
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=m

#
# LED drivers
#
CONFIG_LEDS_NET48XX=m

#
# LED Triggers
#
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=m
CONFIG_LEDS_TRIGGER_IDE_DISK=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=m

#
# InfiniBand support
#
CONFIG_INFINIBAND=m
CONFIG_INFINIBAND_USER_MAD=m
CONFIG_INFINIBAND_USER_ACCESS=m
CONFIG_INFINIBAND_ADDR_TRANS=y
CONFIG_INFINIBAND_MTHCA=m
CONFIG_INFINIBAND_MTHCA_DEBUG=y
CONFIG_INFINIBAND_IPOIB=m
CONFIG_INFINIBAND_IPOIB_DEBUG=y
# CONFIG_INFINIBAND_IPOIB_DEBUG_DATA is not set
CONFIG_INFINIBAND_SRP=m
CONFIG_INFINIBAND_ISER=m

#
# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) #
CONFIG_EDAC=m

#
# Reporting subsystems
#
# CONFIG_EDAC_DEBUG is not set
CONFIG_EDAC_MM_EDAC=m
CONFIG_EDAC_AMD76X=m
CONFIG_EDAC_E7XXX=m
CONFIG_EDAC_E752X=m
CONFIG_EDAC_I82875P=m
CONFIG_EDAC_I82860=m
CONFIG_EDAC_R82600=m
CONFIG_EDAC_POLL=y

#
# Real Time Clock
#
CONFIG_RTC_LIB=m
CONFIG_RTC_CLASS=m

#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=m
CONFIG_RTC_INTF_PROC=m
CONFIG_RTC_INTF_DEV=m
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set

#
# RTC drivers
#
CONFIG_RTC_DRV_X1205=m
CONFIG_RTC_DRV_DS1307=m
CONFIG_RTC_DRV_DS1553=m
CONFIG_RTC_DRV_ISL1208=m
CONFIG_RTC_DRV_DS1672=m
CONFIG_RTC_DRV_DS1742=m
CONFIG_RTC_DRV_PCF8563=m
CONFIG_RTC_DRV_PCF8583=m
CONFIG_RTC_DRV_RS5C348=m
CONFIG_RTC_DRV_RS5C372=m
CONFIG_RTC_DRV_M48T86=m
# CONFIG_RTC_DRV_TEST is not set
CONFIG_RTC_DRV_MAX6902=m
CONFIG_RTC_DRV_V3020=m

#
# DMA Engine support
#
CONFIG_DMA_ENGINE=y

#
# DMA Clients
#
CONFIG_NET_DMA=y

#
# DMA Devices
#
CONFIG_INTEL_IOATDMA=m

#
# File systems
#
CONFIG_EXT2_FS=m
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=m
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_JBD=m
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=m
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
CONFIG_REISERFS_FS_SECURITY=y
CONFIG_JFS_FS=m
CONFIG_JFS_POSIX_ACL=y
CONFIG_JFS_SECURITY=y
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=m
CONFIG_XFS_QUOTA=y
CONFIG_XFS_SECURITY=y
CONFIG_XFS_POSIX_ACL=y
CONFIG_XFS_RT=y
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_DEBUG_MASKLOG=y
CONFIG_MINIX_FS=m
CONFIG_ROMFS_FS=m
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
CONFIG_QUOTA=y
CONFIG_QFMT_V1=m
CONFIG_QFMT_V2=m
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=m
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
CONFIG_NTFS_RW=y

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
CONFIG_CONFIGFS_FS=m

#
# Miscellaneous filesystems
#
CONFIG_ADFS_FS=m
# CONFIG_ADFS_FS_RW is not set
CONFIG_AFFS_FS=m
# CONFIG_ASFS_FS is not set
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_BEFS_FS=m
# CONFIG_BEFS_DEBUG is not set
CONFIG_BFS_FS=m
CONFIG_EFS_FS=m
CONFIG_JFFS_FS=m
CONFIG_JFFS_FS_VERBOSE=0
CONFIG_JFFS_PROC_FS=y
CONFIG_JFFS2_FS=m
CONFIG_JFFS2_FS_DEBUG=0
CONFIG_JFFS2_FS_WRITEBUFFER=y
# CONFIG_JFFS2_SUMMARY is not set
CONFIG_JFFS2_FS_XATTR=y
CONFIG_JFFS2_FS_POSIX_ACL=y
CONFIG_JFFS2_FS_SECURITY=y
# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
CONFIG_JFFS2_ZLIB=y
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
CONFIG_CRAMFS=y
CONFIG_VXFS_FS=m
CONFIG_HPFS_FS=m
CONFIG_QNX4FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
# CONFIG_UFS_FS_WRITE is not set
# CONFIG_UFS_DEBUG is not set

#
# Network File Systems
#
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=m
CONFIG_NFSD_V2_ACL=y
CONFIG_NFSD_V3=y
CONFIG_NFSD_V3_ACL=y
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_ACL_SUPPORT=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
CONFIG_RPCSEC_GSS_KRB5=m
CONFIG_RPCSEC_GSS_SPKM3=m
CONFIG_SMB_FS=m
# CONFIG_SMB_NLS_DEFAULT is not set
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
# CONFIG_CIFS_WEAK_PW_HASH is not set
# CONFIG_CIFS_XATTR is not set
# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
CONFIG_NCP_FS=m
CONFIG_NCPFS_PACKET_SIGNING=y
CONFIG_NCPFS_IOCTL_LOCKING=y
CONFIG_NCPFS_STRONG=y
CONFIG_NCPFS_NFS_NS=y
CONFIG_NCPFS_OS2_NS=y
# CONFIG_NCPFS_SMALLDOS is not set
CONFIG_NCPFS_NLS=y
CONFIG_NCPFS_EXTRAS=y
CONFIG_CODA_FS=m
# CONFIG_CODA_FS_OLD_API is not set
CONFIG_AFS_FS=m
CONFIG_RXRPC=m
CONFIG_9P_FS=m

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
CONFIG_ACORN_PARTITION=y
# CONFIG_ACORN_PARTITION_CUMANA is not set
# CONFIG_ACORN_PARTITION_EESOX is not set
CONFIG_ACORN_PARTITION_ICS=y
# CONFIG_ACORN_PARTITION_ADFS is not set
# CONFIG_ACORN_PARTITION_POWERTEC is not set
CONFIG_ACORN_PARTITION_RISCIX=y
CONFIG_OSF_PARTITION=y
CONFIG_AMIGA_PARTITION=y
CONFIG_ATARI_PARTITION=y
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
CONFIG_BSD_DISKLABEL=y
CONFIG_MINIX_SUBPARTITION=y
CONFIG_SOLARIS_X86_PARTITION=y
CONFIG_UNIXWARE_DISKLABEL=y
CONFIG_LDM_PARTITION=y
# CONFIG_LDM_DEBUG is not set
CONFIG_SGI_PARTITION=y
CONFIG_ULTRIX_PARTITION=y
CONFIG_SUN_PARTITION=y
CONFIG_KARMA_PARTITION=y
CONFIG_EFI_PARTITION=y

#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m

#
# Instrumentation Support
#
CONFIG_PROFILING=y
CONFIG_OPROFILE=m
# CONFIG_KPROBES is not set

#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
CONFIG_MAGIC_SYSRQ=y
CONFIG_UNUSED_SYMBOLS=y
# CONFIG_DEBUG_KERNEL is not set
CONFIG_LOG_BUF_SHIFT=15
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_FS=y
# CONFIG_UNWIND_INFO is not set
CONFIG_EARLY_PRINTK=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
CONFIG_DOUBLEFAULT=y

#
# Security options
#
CONFIG_KEYS=y
# CONFIG_KEYS_DEBUG_PROC_KEYS is not set CONFIG_SECURITY=y
CONFIG_SECURITY_NETWORK=y CONFIG_SECURITY_NETWORK_XFRM=y CONFIG_SECURITY_CAPABILITIES=y
# CONFIG_SECURITY_ROOTPLUG is not set CONFIG_SECURITY_SELINUX=y CONFIG_SECURITY_SELINUX_BOOTPARAM=y CONFIG_SECURITY_SELINUX_BOOTPARAM_VALUE=0 CONFIG_SECURITY_SELINUX_DISABLE=y CONFIG_SECURITY_SELINUX_DEVELOP=y CONFIG_SECURITY_SELINUX_AVC_STATS=y CONFIG_SECURITY_SELINUX_CHECKREQPROT_VALUE=1
# CONFIG_SECURITY_SELINUX_ENABLE_SECMARK_DEFAULT is not set

#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_AES_586=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
CONFIG_CRYPTO_TEST=m

#
# Hardware crypto devices
#
CONFIG_CRYPTO_DEV_PADLOCK=m
CONFIG_CRYPTO_DEV_PADLOCK_AES=y

#
# Library routines
#
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_AUDIT_GENERIC=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_REED_SOLOMON=m
CONFIG_REED_SOLOMON_DEC16=y
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_PLIST=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_KTIME_SCALAR=y

processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 1
model name : Pentium Pro
stepping : 9
cpu MHz : 200.027
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov
bogomips : 400.96

processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 1
model name : Pentium Pro
stepping : 9
cpu MHz : 200.027
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov
bogomips : 400.07

processor : 2
vendor_id : GenuineIntel
cpu family : 6
model : 1
model name : Pentium Pro
stepping : 9
cpu MHz : 200.027
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov
bogomips : 400.09

processor : 3
vendor_id : GenuineIntel
cpu family : 6
model : 1
model name : Pentium Pro
stepping : 9
cpu MHz : 200.027
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov
bogomips : 400.07

00000000-0009efff : System RAM
00000000-00000000 : Crash kernel
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000c8000-000cbfff : Adapter ROM
000f0000-000fffff : System ROM
00100000-0fffffff : System RAM
00100000-00281e12 : Kernel code
00281e13-003127b3 : Kernel data
20000000-2000ffff : 0000:01:00.0
80000000-8000ffff : 0000:00:03.0
d8000000-dbffffff : 0000:00:03.0
de000000-de0fffff : 0000:01:01.0
df000000-df0fffff : 0000:01:01.0
df000000-df0fffff : e100
df100000-df100fff : 0000:01:01.0
df100000-df100fff : e100
df101000-df101fff : 0000:01:00.0
df101000-df101fff : aic7xxx

0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0213-0213 : ISAPnP
02f8-02ff : serial
03c0-03df : vga+
03f8-03ff : serial
0a79-0a79 : isapnp write
0cf8-0cff : PCI conf1
f400-f4ff : 0000:01:00.0
fc00-fc1f : 0000:01:01.0
fc00-fc1f : e100

Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: SEAGATE Model: ST34572WC Rev: 0732
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: SEAGATE Model: ST34572WC Rev: 0732
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 02 Lun: 00
Vendor: SEAGATE Model: ST34572WC Rev: 0732
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 03 Lun: 00
Vendor: SEAGATE Model: ST34572WC Rev: 0732
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: SEAGATE Model: ST34572WC Rev: 0732
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 05 Lun: 00
Vendor: MATSHITA Model: CD-ROM CR-506 Rev: 8S05
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 06 Lun: 00
Vendor: SONY Model: SDT-7000 Rev: 0195
Type: Sequential-Access ANSI SCSI revision: 02

ipv6 226304 18 - Live 0xd09b2000
loop 15048 0 - Live 0xd084d000
ext3 119336 2 - Live 0xd0912000
jbd 52456 1 ext3, Live 0xd088e000
mbcache 8356 1 ext3, Live 0xd0825000
raid1 21056 3 - Live 0xd0840000
md_mod 70388 4 raid1, Live 0xd087b000
ide_generic 1408 0 [permanent], Live 0xd081f000
ide_core 110504 1 ide_generic, Live 0xd08d2000
sd_mod 19040 20 - Live 0xd083a000
aic7xxx 150932 15 - Live 0xd08ac000
scsi_transport_spi 22336 1 aic7xxx, Live 0xd0833000 scsi_mod 124168 3 sd_mod,aic7xxx,scsi_transport_spi, Live 0xd085b000 e100 32232 0 - Live 0xd082a000
mii 5344 1 e100, Live 0xd080f000
processor 28840 0 - Live 0xd0816000

00:03.0 VGA compatible controller: S3 Inc. 86c375 [ViRGE/DX] or 86c385 [ViRGE/GX] (rev 01) (prog-if 00 [VGA controller])
Subsystem: Compaq Computer Corporation ViRGE/GX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 96 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 15
Region 0: Memory at d8000000 (32-bit, non-prefetchable) [size=64M]
Expansion ROM at 80000000 [disabled] [size=64K]
Kernel modules: ipmi_si

00:05.0 EISA bridge: Intel Corporation 82375EB/SB PCI to EISA Bridge (rev 15)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248
Kernel modules: ipmi_si

00:14.0 RAM memory: Intel Corporation 450KX/GX [Orion] - 82453KX/GX Memory controller (rev 05)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Kernel modules: ipmi_si

00:19.0 Host bridge: Intel Corporation 450KX/GX [Orion] - 82454KX/GX PCI bridge (rev 06)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 96, Cache Line Size: 32 bytes
Kernel modules: ipmi_si

00:1a.0 Host bridge: Intel Corporation 450KX/GX [Orion] - 82454KX/GX PCI bridge (rev 06)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 96, Cache Line Size: 32 bytes
Kernel modules: ipmi_si

01:00.0 SCSI storage controller: Adaptec AHA-294x / AIC-7870 (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 96 (2000ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at f400 [disabled] [size=256]
Region 1: Memory at df101000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 20000000 [disabled] [size=64K]
Kernel driver in use: aic7xxx
Kernel modules: ipmi_si, aic7xxx

01:01.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 05)

	Subsystem: Intel Corporation 82558B PRO/100+ PCI (TP)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 96 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 14
	Region 0: Memory at df100000 (32-bit, prefetchable) [size=4K]
	Region 1: I/O ports at fc00 [size=32]
	Region 2: Memory at df000000 (32-bit, non-prefetchable) [size=1M]
	Expansion ROM at de000000 [disabled] [size=1M]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: e100
	Kernel modules: e100, eepro100, ipmi_si

Linux version 2.6.18-6-686 (Debian 2.6.18.dfsg.1-26etch2) ([email protected]) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Fri Feb 19 23:40:03 UTC 2010 BIOS-provided physical RAM map:
BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
BIOS-e801: 0000000000100000 - 0000000010000000 (usable)
0MB HIGHMEM available.
256MB LOWMEM available.
found SMP MP-table at 000f0800
On node 0 totalpages: 65536
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 61440 pages, LIFO batch:15
DMI not present or invalid.
ACPI: Unable to locate RSDP
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OLIVETTI Product ID: CONDOR APIC at: 0xFEE00000
Processor #3 6:1 APIC version 17
Processor #0 6:1 APIC version 17
Processor #1 6:1 APIC version 17
Processor #2 6:1 APIC version 17
I/O APIC #4 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 4
Allocating PCI resources starting at 20000000 (gap: 10000000:f0000000)
Detected 200.027 MHz processor.
Built 1 zonelists. Total pages: 65536
Kernel command line: root=/dev/md1 ro nousb panic=30 pnpbios=off edd=off
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 251956k/262144k available (1543k kernel code, 9644k reserved, 578k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 400.96 BogoMIPS (lpj=801924)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0000fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0000fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 8K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: 0000f3ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
CPU0: Intel Pentium Pro stepping 09
SMP alternatives: switching to SMP code
Booting processor 1/0 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 400.07 BogoMIPS (lpj=800149)
CPU: After generic identify, caps: 0000fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0000fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 8K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: 0000f3ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium Pro stepping 09
SMP alternatives: switching to SMP code
Booting processor 2/1 eip 3000
Initializing CPU#2
Calibrating delay using timer specific routine.. 400.09 BogoMIPS (lpj=800197)
CPU: After generic identify, caps: 0000fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0000fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 8K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: 0000f3ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#2.
CPU2: Intel Pentium Pro stepping 09
SMP alternatives: switching to SMP code
Booting processor 3/2 eip 3000
Initializing CPU#3
Calibrating delay using timer specific routine.. 400.07 BogoMIPS (lpj=800146)
CPU: After generic identify, caps: 0000fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0000fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 8K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: 0000f3ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#3.
CPU3: Intel Pentium Pro stepping 09
Total of 4 processors activated (1601.20 BogoMIPS).
ExtINT not setup in hardware but reported by MP table
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
checking TSC synchronization across 4 CPUs: passed.
Brought up 4 CPUs
migration_cost=6510
checking if image is initramfs... it is
Freeing initrd memory: 4617k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0c2d, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Disabled
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:03.0
PCI: i440KX/GX host bridge 0000:00:19.0: secondary bus 00
PCI: i440KX/GX host bridge 0000:00:1a.0: secondary bus 01
PCI: Firmware left 0000:01:01.0 e100 interrupts enabled, disabling
PCI BIOS passed nonexistent PCI bus 0!
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1303477888.168:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
pnp: SB audio device quirk - increasing port range
pnp: AWE32 quirk - adding two ports
isapnp: Card 'Creative SB AWE64 PnP'
isapnp: 1 Plug & Play card detected total
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Starting balanced_irq
Using IPI No-Shortcut mode
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 196k freed
input: AT Translated Set 2 keyboard as /class/input/input0
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
e100: eth0: e100_probe: addr 0xdf100000, irq 14, MAC addr 00:90:27:13:AC:29
SCSI subsystem initialized
ahc_pci:1:0:0: Using left over BIOS settings
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec aic7870 SCSI adapter>
aic7870: Wide Channel A, SCSI Id=7, 16/253 SCBs

Vendor: SEAGATE Model: ST34572WC Rev: 0732
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled. Depth 8
target0:0:0: Beginning Domain Validation
target0:0:0: wide asynchronous
target0:0:0: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) target0:0:0: Domain Validation skipping write tests target0:0:0: Ending Domain Validation
Vendor: SEAGATE Model: ST34572WC Rev: 0732
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:1:0: Tagged Queuing enabled. Depth 8
target0:0:1: Beginning Domain Validation
target0:0:1: wide asynchronous
target0:0:1: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) target0:0:1: Domain Validation skipping write tests target0:0:1: Ending Domain Validation
Vendor: SEAGATE Model: ST34572WC Rev: 0732
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:2:0: Tagged Queuing enabled. Depth 8
target0:0:2: Beginning Domain Validation
target0:0:2: wide asynchronous
target0:0:2: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) target0:0:2: Domain Validation skipping write tests target0:0:2: Ending Domain Validation
Vendor: SEAGATE Model: ST34572WC Rev: 0732
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:3:0: Tagged Queuing enabled. Depth 8
target0:0:3: Beginning Domain Validation
target0:0:3: wide asynchronous
target0:0:3: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) target0:0:3: Domain Validation skipping write tests target0:0:3: Ending Domain Validation
Vendor: SEAGATE Model: ST34572WC Rev: 0732
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:4:0: Tagged Queuing enabled. Depth 8
target0:0:4: Beginning Domain Validation
target0:0:4: wide asynchronous
target0:0:4: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) target0:0:4: Domain Validation skipping write tests target0:0:4: Ending Domain Validation
Vendor: MATSHITA Model: CD-ROM CR-506 Rev: 8S05
Type: CD-ROM ANSI SCSI revision: 02
target0:0:5: Beginning Domain Validation
target0:0:5: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) target0:0:5: Domain Validation skipping write tests target0:0:5: Ending Domain Validation
Vendor: SONY Model: SDT-7000 Rev: 0195
Type: Sequential-Access ANSI SCSI revision: 02
target0:0:6: Beginning Domain Validation
target0:0:6: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) target0:0:6: Domain Validation skipping write tests target0:0:6: Ending Domain Validation
target0:0:0: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
SCSI device sda: 8250001 512-byte hdwr sectors (4224 MB)
sda: Write Protect is off
sda: Mode Sense: 9f 00 10 08
SCSI device sda: drive cache: write through w/ FUA
SCSI device sda: 8250001 512-byte hdwr sectors (4224 MB)
sda: Write Protect is off
sda: Mode Sense: 9f 00 10 08
SCSI device sda: drive cache: write through w/ FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
target0:0:1: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
SCSI device sdb: 8250001 512-byte hdwr sectors (4224 MB)
sdb: Write Protect is off
sdb: Mode Sense: 9f 00 10 08
SCSI device sdb: drive cache: write through w/ FUA
SCSI device sdb: 8250001 512-byte hdwr sectors (4224 MB)
sdb: Write Protect is off
sdb: Mode Sense: 9f 00 10 08
SCSI device sdb: drive cache: write through w/ FUA
sdb: sdb1 sdb2 sdb3
sd 0:0:1:0: Attached scsi disk sdb
target0:0:2: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
SCSI device sdc: 8250001 512-byte hdwr sectors (4224 MB)
sdc: Write Protect is off
sdc: Mode Sense: 9f 00 10 08
SCSI device sdc: drive cache: write through w/ FUA
SCSI device sdc: 8250001 512-byte hdwr sectors (4224 MB)
sdc: Write Protect is off
sdc: Mode Sense: 9f 00 10 08
SCSI device sdc: drive cache: write through w/ FUA
sdc: sdc1 sdc2 sdc3
sd 0:0:2:0: Attached scsi disk sdc
target0:0:3: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
SCSI device sdd: 8250001 512-byte hdwr sectors (4224 MB)
sdd: Write Protect is off
sdd: Mode Sense: 9f 00 10 08
SCSI device sdd: drive cache: write through w/ FUA
SCSI device sdd: 8250001 512-byte hdwr sectors (4224 MB)
sdd: Write Protect is off
sdd: Mode Sense: 9f 00 10 08
SCSI device sdd: drive cache: write through w/ FUA
sdd: sdd1 sdd2 sdd3
sd 0:0:3:0: Attached scsi disk sdd
target0:0:4: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
SCSI device sde: 8250001 512-byte hdwr sectors (4224 MB)
sde: Write Protect is off
sde: Mode Sense: 9f 00 10 08
SCSI device sde: drive cache: write through w/ FUA
SCSI device sde: 8250001 512-byte hdwr sectors (4224 MB)
sde: Write Protect is off
sde: Mode Sense: 9f 00 10 08
SCSI device sde: drive cache: write through w/ FUA
sde: sde1 sde2 sde3
sd 0:0:4:0: Attached scsi disk sde
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Probing IDE interface ide0...
Probing IDE interface ide1...
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
md: raid1 personality registered for level 1
md: md0 stopped.
md: bind<sdb1>
md: bind<sdc1>
md: bind<sdd1>
md: bind<sde1>
md: bind<sda1>
raid1: raid set md0 active with 5 out of 5 mirrors
md: md1 stopped.
md: bind<sdb2>
md: bind<sdc2>
md: bind<sdd2>
md: bind<sde2>
md: bind<sda2>
raid1: raid set md1 active with 5 out of 5 mirrors
md: md2 stopped.
md: bind<sdb3>
md: bind<sdc3>
md: bind<sdd3>
md: bind<sde3>
md: bind<sda3>
raid1: raid set md2 active with 5 out of 5 mirrors
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 489848k swap on /dev/md2. Priority:-1 extents:1 across:489848k EXT3 FS on md1, internal journal
loop: loaded (max 8 devices)
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ADDRCONF(NETDEV_UP): eth0: link is not ready
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present

Ingo Molnar

2011-04-22 13:47 UTC #1 lore raw

Quoted 5 lines · Chris Samuel

This box has given me good service over the past 8 years or so and I'd hate to have to retire it now due to this when I feel Linux should still work on it..
Any ideas please ?

Have you tried the earlyprintk=vga boot parameter yet? Maybe that shows more than just a silent hang ...

Other than that, do you have some other box where you can build bzImages for this system in reasonable time? If yes then you might be able to bisect to the commit that broke it.

Thanks,

Ingo

Yinghai Lu

2011-04-22 19:09 UTC #2 lore raw

Quoted 7 lines · Ingo Molnar

Quoted 4 lines · Chris Samuel
This box has given me good service over the past 8 years or so and I'd hate to have to retire it now due to this when I feel Linux should still work on it..

Quoted 8 lines

Quoted 1 line
Any ideas please ?
Have you tried the earlyprintk=vga boot parameter yet? Maybe that shows more than just a silent hang ...
Other than that, do you have some other box where you can build bzImages for this system in reasonable time? If yes then you might be able to bisect to the commit that broke it.

with Chris's config for 2.6.39-rc4, current tip tree says:

kernel/sched.c: In function ‘sched_init’:
kernel/sched.c:7845:28: error: ‘load_balance_tmpmask’ undeclared (first use in this function)
kernel/sched.c:7845:28: note: each undeclared identifier is reported only once for each function it appears in kernel/sched.c:7845:3: warning: type defaults to ‘int’ in type name kernel/sched.c:7845:28: warning: initialization makes pointer from integer without a cast
kernel/sched.c:7845:3: warning: type defaults to ‘int’ in type name

Ingo Molnar

2011-04-22 19:29 UTC #3 lore raw

Quoted 11 lines · Yinghai Lu

with Chris's config for 2.6.39-rc4, current tip tree says:
kernel/sched.c: In function ‘sched_init’:
kernel/sched.c:7845:28: error: ‘load_balance_tmpmask’ undeclared (first use in this function)
kernel/sched.c:7845:28: note: each undeclared identifier is reported only once for each function it appears in kernel/sched.c:7845:3: warning: type defaults to ‘int’ in type name kernel/sched.c:7845:28: warning: initialization makes pointer from integer without a cast
kernel/sched.c:7845:3: warning: type defaults to ‘int’ in type name

Which sha1? It builds fine here on:

ae1e16c: Merge branch 'perf/urgent'

Thanks,

Ingo

Yinghai Lu

2011-04-22 19:47 UTC #4 lore raw

Quoted 15 lines · Ingo Molnar

Quoted 11 lines · Yinghai Lu
with Chris's config for 2.6.39-rc4, current tip tree says:
kernel/sched.c: In function ‘sched_init’:
kernel/sched.c:7845:28: error: ‘load_balance_tmpmask’ undeclared (first use in this function)
kernel/sched.c:7845:28: note: each undeclared identifier is reported only once for each function it appears in kernel/sched.c:7845:3: warning: type defaults to ‘int’ in type name kernel/sched.c:7845:28: warning: initialization makes pointer from integer without a cast
kernel/sched.c:7845:3: warning: type defaults to ‘int’ in type name

Quoted 4 lines

Which sha1? It builds fine here on:
ae1e16c: Merge branch 'perf/urgent'

one local patch caused the problem.

kernel/sched.c +4 -9

Index: linux-2.6/kernel/sched.c
===================================================================
@@ -7808,9 +7808,6 @@ void __init sched_init(void)
 #ifdef CONFIG_RT_GROUP_SCHED
 	alloc_size += 2 * nr_cpu_ids * sizeof(void **);
 #endif
-#ifdef CONFIG_CPUMASK_OFFSTACK
-	alloc_size += num_possible_cpus() * cpumask_size();
-#endif
 	if (alloc_size) {
 		ptr = (unsigned long)kzalloc(alloc_size, GFP_NOWAIT);

@@ -7830,14 +7827,12 @@ void __init sched_init(void)
 		ptr += nr_cpu_ids * sizeof(void **);
 
 #endif /* CONFIG_RT_GROUP_SCHED */
-#ifdef CONFIG_CPUMASK_OFFSTACK
-		for_each_possible_cpu(i) {
-			per_cpu(load_balance_tmpmask, i) = (void *)ptr;
-			ptr += cpumask_size();
-		}
-#endif /* CONFIG_CPUMASK_OFFSTACK */
 	}
 
+	for_each_possible_cpu(i)
+		zalloc_cpumask_var_node(&per_cpu(load_balance_tmpmask, i),
+					GFP_NOWAIT, cpu_to_node(i));
+
 #ifdef CONFIG_SMP
 	init_defrootdomain();
 #endif

Sorry for noisy.

Thanks

Yinghai

Chris Samuel

author

2011-04-23 00:20 UTC #5 lore raw

In reply to Ingo Molnar

Hi Ingo,

Quoted 2 lines · Ingo Molnar

Have you tried the earlyprintk=vga boot parameter yet? Maybe that shows more than just a silent hang ...

Thanks for that, just responded to Alan's email mentioning the same option - I'd not come stumbled across it before. It reveals the cause is the kernel misdetecting the amount of LOWMEM as 16MB and, I suspect, is the same issue as I had an offlist conversation with H. Peter Anvin with in 2008 which tailed off due to work pressure on his part. There are more details in my response to Alan.

Quoted 3 lines

Other than that, do you have some other box where you can build bzImages for this system in reasonable time? If yes then you might be able to bisect to the commit that broke it.

I can indeed, I'm lucky enough to be able to build that image in about 4 minutes on my production desktop. Is that still of use given that there's now a better view of what's going on ?

All the best,
Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

Alan Cox

2011-04-22 16:33 UTC #6 lore raw

In reply to Chris Samuel

Quoted 12 lines

All result in the same behaviour and I'm somewhat at a loss as to how to debug this further, being a sysadmin rather than a real kernel hacker. :-(
I've attached the 2.6.39-rc4 kernel config from point 4, and the kernel config for the working Debian kernel (2.6.18-6-686).
I've also attached the contents of /proc/cpuinfo, /proc/io*, /proc/scsi/scsi, /proc/modules and the output of lspci -vvv and of dmesg from Debian Sarge running the Debian Etch kernel (2.6.18-6-686).

Quoted 5 lines

This box has given me good service over the past 8 years or so and I'd hate to have to retire it now due to this when I feel Linux should still work on it..
Any ideas please ?

earlyprintk=vga

(or better yet earlyprintk=ttyS0 and a serial port)

There are a couple of PPro funnies - there's an area of memory that must be excluded due to a chip errata and I seem to remember some PPro boxes also having slightly quirking E820 (BIOS memory reporting behaviour)

Alan

Chris Samuel

author

2011-04-23 00:16 UTC #7 lore raw

Syt mae Alan! ;-)

Quoted 1 line · Alan Cox

earlyprintk=vga

Ahh, that's a new one on me, and it reveals that the kernel has gone from 2.6.18 detecting:

256MB LOWMEM available.

to 2.6.39-rc4 detecting:

16MB LOWMEM available.

That would explain an awful lot..

Quoted 1 line

(or better yet earlyprintk=ttyS0 and a serial port)

Hmm, I might still have a null modem cable hanging around..

Quoted 4 lines

There are a couple of PPro funnies - there's an area of memory that must be excluded due to a chip errata and I seem to remember some PPro boxes also having slightly quirking E820 (BIOS memory reporting behaviour)

Sigh, that's just reminded me that a couple of years ago I had a private discussion with H. Peter Anvin about 2.6.25 panic'ing on boot with:

initrd extends beyond end of memory (0x0ffef173 > ox01000000)

He gave me a modified syslinux to dump out memory information and it reported:

INT 15h = f000:f859 DOS RAM: 638K (0x9f800) INT 12h: 638K (0x9f800) INT 15 88: 0x3c00 (15360K) INT 15 E801: 0x0000 (0K) 0x0000 (0K)

He responded with:

# Right... you have a system dependent on E801, and somehow E801

# returns crap.
#
# I'm going to cook up a modified meminfo.c32 for you and see if
# we can't track this down.

Unfortunately nothing happened and when I prodded him it turned out he'd been too busy, so I just kept on running old kernels from that point on and completely forgot about why. :-(

Hope life is still good in Abertawe!

Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

Yuhong Bao

2011-04-23 01:34 UTC #8 lore raw

Quoted 13 lines

Sigh, that's just reminded me that a couple of years ago I had a private discussion with H. Peter Anvin about 2.6.25 panic'ing on boot with:
initrd extends beyond end of memory (0x0ffef173 > ox01000000)
He gave me a modified syslinux to dump out memory information and it reported:
INT 15h = f000:f859 DOS RAM: 638K (0x9f800) INT 12h: 638K (0x9f800) INT 15 88: 0x3c00 (15360K) INT 15 E801: 0x0000 (0K) 0x0000 (0K)

Quoted 7 lines

He responded with:
# Right... you have a system dependent on E801, and somehow E801
# returns crap.
#
# I'm going to cook up a modified meminfo.c32 for you and see if
# we can't track this down.

This is a stupid BIOS, but do you know if it used E820 in the old kernel?
I wonder if this has something to do with the changes made to support ACPI 3.0 changes to E820? This would be easy to diagnose with DOS DEBUG with no himem.sys loaded.

Yuhong Bao

Chris Samuel

author

2011-04-23 01:36 UTC #9 lore raw

Quoted 1 line · Yuhong Bao

This is a stupid BIOS,

I won't argue with that, it is at least 15 years old..

Quoted 1 line

but do you know if it used E820 in the old kernel?

No, it was using E801:

BIOS-provided physical RAM map:
BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
BIOS-e801: 0000000000100000 - 0000000010000000 (usable)

The new kernel has the '1' in the top end of the second part being one place to the right:

BIOS-provided physical RAM map:
BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
BIOS-e801: 0000000000100000 - 0000000001000000 (usable)

Quoted 2 lines

I wonder if this has something to do with the changes made to support ACPI 3.0 changes to E820?

I suspect not, given it's not using E820. But could be wrong. ;-)

Quoted 2 lines

This would be easy to diagnose with DOS DEBUG with no himem.sys loaded.

Would be happy to try with some instructions if it would help.

cheers,
Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

Yuhong Bao

2011-04-23 01:46 UTC #10 lore raw

If it was really BIOS-e801 and not BIOS-88 returning this, looks like this is probably a kernel bug in the parsing of the results.

Quoted 4 lines

Quoted 2 lines
This would be easy to diagnose with DOS DEBUG with no himem.sys loaded.
Would be happy to try with some instructions if it would help.

Enter these instructions using the A command and execute with the T command:
mov AX, E801
INT 15
INT 3
And provide the results of the AX, BX, CX, and DX registers after the INT 15h.

Yuhong Bao

H. Peter Anvin

reviewer

2011-04-23 02:26 UTC #11 lore raw

Quoted 5 lines · Yuhong Bao

If it was really BIOS-e801 and not BIOS-88 returning this, looks like this is probably a kernel bug in the parsing of the results.
Quoted 3 lines
Quoted 2 lines
This would be easy to diagnose with DOS DEBUG with no himem.sys loaded.

Quoted 7 lines

Quoted 1 line
Would be happy to try with some instructions if it would help.
Enter these instructions using the A command and execute with the T command:
mov AX, E801
INT 15
INT 3
And provide the results of the AX, BX, CX, and DX registers after the INT 15h.

Executing these from DOS DEBUG won't give you real results, because DOS intercepts this call.

-hpa

Signature · 2 lines

H. Peter Anvin, Intel Open Source Technology Center
I work for Intel.  I don't speak on their behalf.

Yuhong Bao

2011-04-23 02:31 UTC #12 lore raw

Quoted 4 lines

Executing these from DOS DEBUG won't give you real results, because DOS intercepts this call.

Which is why I said to do it without himem.sys loaded in a previous email. Yuhong Bao

Chris Samuel

author

2011-04-23 04:34 UTC #13 lore raw

In reply to Yuhong Bao

Quoted 8 lines · Yuhong Bao

Quoted 1 line
Would be happy to try with some instructions if it would help.
Enter these instructions using the A command and execute with the T
command: mov AX, E801
INT 15
INT 3
And provide the results of the AX, BX, CX, and DX registers after the INT 15h.

I should have asked previously - is this possible with FreeDOS ?

I don't have an DOS media myself.

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

Chris Samuel

author

2011-04-23 05:22 UTC #14 lore raw

In reply to Yuhong Bao

Quoted 7 lines · Yuhong Bao

Enter these instructions using the A command and execute with the T
command: mov AX, E801
INT 15
INT 3
And provide the results of the AX, BX, CX, and DX registers after the INT 15h.

OK, so I'm a novice so I'll recap what I did. Starting with FreeDOS boot floppy and copied debug.com and debug98.com to the FreeDOS directory on it. Booted from the floppy, selected option 2 (safe mode, no drivers loaded). Typed debug and then:

- A
2890:0100 mov AX, E801
2890:0103 int 15
2890:0105 int 3
2890:0106
- t
AX=E801 BX=0000 CX=0000 DX=0000 SP=FFFE BP=0000 SI=0000 DI=0000 DS=2890 ES=2890 SS=2890 CS=2890 IP=0103 NV UP DI PL NZ NA PO NC
2890:0103 CD15 INT 15
-

Does that look correct ? I presume it was just <enter> to leave the 'A' mode to go back to the command mode ?

cheers,
Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

A message that is not in the archive (sent off-list or not yet received): [email protected]

Yuhong Bao

2011-04-23 10:47 UTC #17 lore raw

FYI, I walked Chris on how to use DOS DEBUG via private email, and below is the results after the INT 15, using the instruction sequence I posted on the mailing list.Notice HIMEM was not loaded.

----------------------------------------

Quoted 31 lines

From: [email protected]
To: [email protected]
Subject: Re: 2.6.38.3 and 2.6.39-rc4 hangs after "Booting the kernel" on quad Pentium Pro system
Date: Sat, 23 Apr 2011 18:55:44 +1000
Quoted 2 lines · Yuhong Bao
Actually, execute with G instead, and do it without HIMEM.SYS loaded.
I couldn't see any HIMEM.SYS on the FreeDOS floppy (including looking for hidden files) so I'm presuming it's not there. There was a HIMEM.EXE so I've renamed it to NOHIMEM.OFF in the hope that it won't get executed, even in the safe mode I was using.
Using G instead of A I now get:
-G
Unexpected breakpoint interrupt.
AX=3C00 BX=0F00 CX=0000 DX=0000 SP=FFFE BP=0000 SI=0000 DI=0000 DS=2890 ES=2890 SS=2890 CS=2890 IP=0106 NV UP DI PL NZ NA PE NC 2890:0106 0000 ADD [BX+SI], AL D:0F00=00
-
cheers,
Chris
--
Chris Samuel : http://www.csamuel.org/ : Melbourne, VIC
This email may come with a PGP signature as a file. Do not panic. For more info see: http://en.wikipedia.org/wiki/OpenPGP

Thomas Meyer

2011-04-23 13:52 UTC #18 lore raw

Am Samstag, den 23.04.2011, 03:47 -0700 schrieb Yuhong Bao:

Quoted 20 lines

FYI, I walked Chris on how to use DOS DEBUG via private email, and below is the results after the INT 15, using the instruction sequence I posted on the mailing list.Notice HIMEM was not loaded.
----------------------------------------
Quoted 17 lines
From: [email protected]
To: [email protected]
Subject: Re: 2.6.38.3 and 2.6.39-rc4 hangs after "Booting the kernel" on quad Pentium Pro system
Date: Sat, 23 Apr 2011 18:55:44 +1000
Quoted 2 lines · Yuhong Bao
Actually, execute with G instead, and do it without HIMEM.SYS loaded.
I couldn't see any HIMEM.SYS on the FreeDOS floppy (including looking for hidden files) so I'm presuming it's not there. There was a HIMEM.EXE so I've renamed it to NOHIMEM.OFF in the hope that it won't get executed, even in the safe mode I was using.
Using G instead of A I now get:

Quoted 7 lines

Quoted 7 lines
-G
Unexpected breakpoint interrupt.
AX=3C00 BX=0F00 CX=0000 DX=0000 SP=FFFE BP=0000 SI=0000 DI=0000 DS=2890 ES=2890 SS=2890 CS=2890 IP=0106 NV UP DI PL NZ NA PE NC 2890:0106 0000 ADD [BX+SI], AL D:0F00=00
-

so your bios seems to report the size in AX/BX. the code in arch/x86/boot/memory.c move the return sizes from CX/DX into AX/BX, when CX or DX is not zero.

Could you try to change the line:

	} else if (oreg.ax == 15*1024) {
		boot_params.alt_mem_k = (oreg.dx << 6) + oreg.ax;

	} else if (oreg.ax == 15*1024) {
		boot_params.alt_mem_k = (oreg.bx << 6) + oreg.ax;

That should fix your misdetection.

The assembler code in arch/i386/boot/setup.S seemed to move AX/BX into CX/DX, when CX and(!) DX were zero. Then used CX/DX to calc the memory size.

PS: gitk --follow arch/x86/boot/memory.c seems to react strangley...

H. Peter Anvin

reviewer

2011-04-23 17:52 UTC #19 lore raw

Quoted 14 lines · Thomas Meyer

so your bios seems to report the size in AX/BX. the code in arch/x86/boot/memory.c move the return sizes from CX/DX into AX/BX, when CX or DX is not zero.
Could you try to change the line:
	} else if (oreg.ax == 15*1024) {
		boot_params.alt_mem_k = (oreg.dx<<  6) + oreg.ax;
to
	} else if (oreg.ax == 15*1024) {
		boot_params.alt_mem_k = (oreg.bx<<  6) + oreg.ax;

Quoted 8 lines

That should fix your misdetection.
The assembler code in arch/i386/boot/setup.S seemed to move AX/BX into CX/DX, when CX and(!) DX were zero. Then used CX/DX to calc the memory size.
PS: gitk --follow arch/x86/boot/memory.c seems to react strangley...

Ah yes, this should have been bx; ax/bx and cx/dx forms pairs (unlike the normal x86 convention of DX:AX and BX:CX forming pairs), and it doesn't make sense to mix and match them.

-hpa

Chris Samuel

author

2011-04-23 23:24 UTC #20 lore raw

In reply to Thomas Meyer

Hi Thomas,

Quoted 10 lines · Thomas Meyer

Could you try to change the line:

        } else if (oreg.ax == 15*1024) {
                boot_params.alt_mem_k = (oreg.dx << 6) + oreg.ax;

        } else if (oreg.ax == 15*1024) {
                boot_params.alt_mem_k = (oreg.bx << 6) + oreg.ax;

That should fix your misdetection.

Took me a while to spot the D->B change - good catch!

I can confirm the allnoconfig now no longer hangs and proceeds to panic about not being able to mount the rootfs, which is good. I'll build a more functional kernel now and check it boots OK.

All the best,
Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

Chris Samuel

author

2011-04-24 00:16 UTC #21 lore raw

In reply to Thomas Meyer

Quoted 1 line · Thomas Meyer

That should fix your misdetection.

A fuller kernel does proceed further than before, before running into issues where both the e100 and aix7xxx drivers complain about not being able to find their IRQ's and that this might be due to a buggy MP table.

I presume this is unrelated to the initial problem ?

cheers,
Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

Chris Samuel

author

2011-04-24 00:22 UTC #22 lore raw

Quoted 4 lines · Chris Samuel

A fuller kernel does proceed further than before, before running into issues where both the e100 and aix7xxx drivers complain about not being able to find their IRQ's and that this might be due to a buggy MP table.

Booting with noapic nolapic removes the IRQ warning but the system still times out trying to mount the root filesystem and reboots itself.

I'll be away for a day or two now.

All the best,
Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

Yinghai Lu

2011-04-24 08:46 UTC #23 lore raw

Quoted 10 lines · Chris Samuel

Quoted 4 lines · Chris Samuel
A fuller kernel does proceed further than before, before running into issues where both the e100 and aix7xxx drivers complain about not being able to find their IRQ's and that this might be due to a buggy MP table.
Booting with noapic nolapic removes the IRQ warning but the system still times out trying to mount the root filesystem and reboots itself.

You may need to your .config to have
CONFIG_SMP
CONFIG_PCI
CONFIG_X86_MPPARSE
set to use mptable from BIOS.

Thanks

Yinghai

Chris Samuel

author

2011-04-25 11:14 UTC #24 lore raw

Hello Yinghai,

Quoted 5 lines · Yinghai Lu

You may need to your .config to have
CONFIG_SMP
CONFIG_PCI
CONFIG_X86_MPPARSE
set to use mptable from BIOS.

Thanks for that - I already have all 3 of those set I'm afraid.

All the best,
Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

tip-bot for H. Peter Anvin

2011-04-25 23:27 UTC #25 lore raw

[tip:x86/urgent] x86, setup: When probing memory with e801, use ax/bx as a pair

In reply to Thomas Meyer

Commit-ID:  39b68976ac653cfdc7f872a293e8b7928de2dcc6
Gitweb:     http://git.kernel.org/tip/39b68976ac653cfdc7f872a293e8b7928de2dcc6
Author:     H. Peter Anvin <[email protected]>
AuthorDate: Mon, 25 Apr 2011 14:52:37 -0700
Committer:  H. Peter Anvin <[email protected]>
CommitDate: Mon, 25 Apr 2011 14:52:37 -0700

x86, setup: When probing memory with e801, use ax/bx as a pair

When we use BIOS function e801 to probe memory, we should use ax/bx (or cx/dx) as a pair, not mix and match. This was a typo during the translation from assembly code, and breaks at least one set of machines in the field (which return cx = dx = 0).

Reported-and-tested-by Chris Samuel <[email protected]>

Fix-proposed-by Thomas Meyer <[email protected]>

Link http://lkml.kernel.org/r/[email protected] open here

---
 arch/x86/boot/memory.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

arch/x86/boot/memory.c +1 -1

index cae3feb..db75d07 100644
@@ -91,7 +91,7 @@ static int detect_memory_e801(void)
 	if (oreg.ax > 15*1024) {
 		return -1;	/* Bogus! */
 	} else if (oreg.ax == 15*1024) {
-		boot_params.alt_mem_k = (oreg.dx << 6) + oreg.ax;
+		boot_params.alt_mem_k = (oreg.bx << 6) + oreg.ax;
 	} else {
 		/*
 		 * This ignores memory above 16MB if we have a memory

Chris Samuel

author

2011-04-26 04:50 UTC #26 lore raw

Re: [tip:x86/urgent] x86, setup: When probing memory with e801, use ax/bx as a pair

Quoted 1 line · tip-bot for H. Peter Anvin

x86, setup: When probing memory with e801, use ax/bx as a pair

ACK. Thanks!

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

Ingo Molnar

2011-04-26 08:12 UTC #27 lore raw

Re: [tip:x86/urgent] x86, setup: When probing memory with e801, use ax/bx as a pair

Quoted 5 lines · Chris Samuel

Quoted 1 line · tip-bot for H. Peter Anvin
x86, setup: When probing memory with e801, use ax/bx as a pair
ACK. Thanks!

Nice!

Just asking, does the box now boot to user-space, or are there other regressions left?

Thanks,

Ingo

Chris Samuel

author

2011-04-27 03:30 UTC #28 lore raw

Re: [tip:x86/urgent] x86, setup: When probing memory with e801, use ax/bx as a pair

Hi Ingo,

Quoted 2 lines · Ingo Molnar

Just asking, does the box now boot to user-space, or are there other regressions left?

Well I now have to boot the box with "noapic" otherwise I hit IRQ problems in the e100 and aic7xxx drivers, they report:

can't find IRQ for PCI INT A; probably buggy MP table

Even with "noapic" the user space seems to try and load the software RAID before the SCSI driver resulting in it timing out locating the root filesystem and resetting the box. I suspect that may be an initramfs issue though..

cheers,
Chris

Signature · 1 line

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

Chris Samuel

author

2011-05-05 11:57 UTC #29 lore raw

Re: [tip:x86/urgent] x86, setup: When probing memory with e801, use ax/bx as a pair

In reply to Ingo Molnar

Quoted 2 lines · Ingo Molnar

Just asking, does the box now boot to user-space, or are there other regressions left?

Final update on this - I can now boot all the way to userspace successfully using an unpatched 2.6.39-rc6 with the parameters:

noapic scsi_mod.scan=sync

So I'm really happy, thanks so much to everyone for their help!

All the best,
Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

Ingo Molnar

2011-05-05 12:11 UTC #30 lore raw

Re: [tip:x86/urgent] x86, setup: When probing memory with e801, use ax/bx as a pair

Quoted 11 lines · Chris Samuel

Quoted 2 lines · Ingo Molnar
Just asking, does the box now boot to user-space, or are there other regressions left?
Final update on this - I can now boot all the way to userspace successfully using an unpatched 2.6.39-rc6 with the parameters:
noapic scsi_mod.scan=sync
So I'm really happy, thanks so much to everyone for their help!

Thanks for the update!

Note that the noapic and the scsi-sync-scan boot parameter suggests that there's two regressions remaining.

The stock kernel wont boot - you can work it around via boot options but most users wont be able to do that.

Thanks,

Ingo

Chris Samuel

author

2011-05-06 11:47 UTC #31 lore raw

Re: [tip:x86/urgent] x86, setup: When probing memory with e801, use ax/bx as a pair

Quoted 1 line · Ingo Molnar

Thanks for the update!

My pleasure.

Quoted 2 lines

Note that the noapic and the scsi-sync-scan boot parameter suggests that there's two regressions remaining.

Understood, I would guess that the SCSI one would map to the introduction of the async scsi scanning patch in 2.6.19-rc2 and its enablement in later Ubuntu kernels.

No idea on the APIC one but I'm happy to try and bisect both cases if you'd like me to try ?

Quoted 2 lines

The stock kernel wont boot - you can work it around via boot options but most users wont be able to do that.

Indeed - though at the moment you can't even install a current Debian release as the boot loader on the install CD locks the box up. :-(

cheers,
Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

Ingo Molnar

2011-05-06 12:05 UTC #32 lore raw

Re: [tip:x86/urgent] x86, setup: When probing memory with e801, use ax/bx as a pair

Quoted 4 lines · Chris Samuel

Quoted 1 line · Ingo Molnar
Thanks for the update!

Quoted 8 lines

My pleasure.
Quoted 2 lines
Note that the noapic and the scsi-sync-scan boot parameter suggests that there's two regressions remaining.
Understood, I would guess that the SCSI one would map to the introduction of the async scsi scanning patch in 2.6.19-rc2 and its enablement in later Ubuntu kernels.

Yeah. Async SCSI scanning was not supposed to break any existing setup.

Quoted 2 lines

No idea on the APIC one but I'm happy to try and bisect both cases if you'd like me to try ?

I could definitely do something about the APIC regression if managed to narrow down the commit range (a specific guilty commit would be fantastic of course). If the regression got introduced after the e801 regression you'll need to run:

git cherry-pick 39b68976ac65

at every bisection step that needs that fix - but still bisect as if that extra commit was not there. (bisection will throw away that cherry-picking temporary tree so you will have to re-pick the commit again and again)

Note that during bisection the current tree might jump in and out of regions that need this fix, so be prepared to have to do the cherry-picking at random places. You can attempt the cherry-pick at every step and you will get a conflict and it will not succeed if the fix is not needed. You can throw away the conflicting state via 'git reset --hard'.

Quoted 6 lines

Quoted 2 lines
The stock kernel wont boot - you can work it around via boot options but most users wont be able to do that.
Indeed - though at the moment you can't even install a current Debian release as the boot loader on the install CD locks the box up. :-(

Is that hang due to one of these 3 regressions - or is it a fourth regression perhaps?

While the installed base of your hardware is small, i think such old-hardware testing is still very valuable feedback to us: it gives us a feel for how corrosive our development process is to long-term (10+ years) stability.

Thanks,

Ingo

Chris Samuel

author

2011-05-06 12:10 UTC #33 lore raw

Re: [tip:x86/urgent] x86, setup: When probing memory with e801, use ax/bx as a pair

Quoted 8 lines · Ingo Molnar

Quoted 3 lines · Chris Samuel
Understood, I would guess that the SCSI one would map to the introduction of the async scsi scanning patch in 2.6.19-rc2 and its enablement in later Ubuntu kernels.
Yeah. Async SCSI scanning was not supposed to break any existing setup.

Well that'd be about my luck at the moment. ;-)

Quoted 8 lines

Quoted 2 lines
No idea on the APIC one but I'm happy to try and bisect both cases if you'd like me to try ?
I could definitely do something about the APIC regression if managed to narrow down the commit range (a specific guilty commit would be fantastic of course). If the regression got introduced after the e801 regression you'll need to run:

Quoted 6 lines

git cherry-pick 39b68976ac65
at every bisection step that needs that fix - but still bisect as if that extra commit was not there. (bisection will throw away that cherry-picking temporary tree so you will have to re-pick the commit again and again)

That's great, will try and see what I can do. It might take a little bit of time due to work commitments prior to a (planned) trip to hospital next Thursday.

Quoted 6 lines

Note that during bisection the current tree might jump in and out of regions that need this fix, so be prepared to have to do the cherry-picking at random places. You can attempt the cherry-pick at every step and you will get a conflict and it will not succeed if the fix is not needed. You can throw away the conflicting state via 'git reset --hard'.

Understood, thanks!

Quoted 6 lines

Quoted 3 lines
Indeed - though at the moment you can't even install a current Debian release as the boot loader on the install CD locks the box up. :-(
Is that hang due to one of these 3 regressions - or is it a fourth regression perhaps?

This is before it boots the kernel, so I'd guess something in whatever they are using for the Squeeze install CD - perhaps grub2 now ?

Quoted 4 lines

While the installed base of your hardware is small, i think such old-hardware testing is still very valuable feedback to us: it gives us a feel for how corrosive our development process is to long-term (10+ years) stability.

Great, as long as this is more useful than just fixing my problems!

cheers,
Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

Yuhong Bao

2011-05-30 04:55 UTC #34 lore raw

Re: [tip:x86/urgent] x86, setup: When probing memory with e801, use ax/bx as a pair

In reply to tip-bot for H. Peter Anvin

Quoted 1 line

x86, setup: When probing memory with e801, use ax/bx as a pair

I think it is time to push this patch into stable branches too.

H. Peter Anvin

reviewer

2011-04-23 02:04 UTC #35 lore raw

In reply to Yuhong Bao

Quoted 7 lines · Yuhong Bao

This is a stupid BIOS, but do you know if it used E820 in the old kernel?
I wonder if this has something to do with the changes made to support ACPI 3.0 changes to E820? This would be easy to diagnose with DOS DEBUG with no himem.sys loaded.
Yuhong Bao

I suspect this broke during the rewrite of the setup code to C in 2007.

-hpa

Signature · 2 lines

H. Peter Anvin, Intel Open Source Technology Center
I work for Intel.  I don't speak on their behalf.

Chris Samuel

author

2011-04-23 06:44 UTC #36 lore raw

Quoted 2 lines · H. Peter Anvin

I suspect this broke during the rewrite of the setup code to C in 2007.

Looking at arch/x86/boot/memory.c I see the snipped:

} else {
/*
* This ignores memory above 16MB if we have a memory
* hole there. If someone actually finds a machine
* with a memory hole at 16MB and no support for
* 0E820h they should probably generate a fake e820
* map.
*/
boot_params.alt_mem_k = oreg.ax;
}

Could this be what's going on ? Or am I just grasping at straws ? :-)

cheers,
Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

A message that is not in the archive (sent off-list or not yet received): [email protected]

Chris Samuel

author

2011-04-23 01:37 UTC #38 lore raw

Quoted 1 line · H. Peter Anvin

Sorry, I had forgotten... let's see if we can't make this happen.

Thanks and not a problem, my fault for having let it lapse in 2008!

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

Alan Cox

2011-04-23 09:34 UTC #39 lore raw

In reply to Chris Samuel

Quoted 1 line · On Sat, 23 Apr 2011 10:16:18 +1000 Chris Samuel <[email protected]> wrote:

Syt mae Alan! ;-)

G'day ;)

Quoted 10 lines

Ahh, that's a new one on me, and it reveals that the kernel has gone from 2.6.18 detecting:
256MB LOWMEM available.
to 2.6.39-rc4 detecting:
16MB LOWMEM available.
That would explain an awful lot..

Could be something has disturbed its memory detect or could be a bug in the PPro memory quirk.

If you boot with mem= and force the memory size what happens ?

Quoted 2 lines

INT 15h = f000:f859 DOS RAM: 638K (0x9f800) INT 12h: 638K (0x9f800) INT 15 88: 0x3c00 (15360K) INT 15 E801: 0x0000 (0K) 0x0000 (0K)

Ah.. do you have a BIOS setting called something like OS/2 compatibility ?

Quoted 1 line

Hope life is still good in Abertawe!

This part of the world has changed rather a lot. Not sure you'd recognize half of it.

Alan

Chris Samuel

author

2011-04-23 10:36 UTC #40 lore raw

Quoted 5 lines · Alan Cox

Quoted 1 line · On Sat, 23 Apr 2011 10:16:18 +1000 Chris Samuel <[email protected]> wrote:
Syt mae Alan! ;-)
G'day ;)

Touché!

Quoted 6 lines

Quoted 1 line
That would explain an awful lot..
Could be something has disturbed its memory detect or could be a bug in the PPro memory quirk.
If you boot with mem= and force the memory size what happens ?

Same behaviour I'm afraid, hangs claiming 16MB of LOWMEM. :-(

Quoted 6 lines

Quoted 3 lines
INT 15h = f000:f859 DOS RAM: 638K (0x9f800) INT 12h: 638K (0x9f800) INT 15 88: 0x3c00 (15360K) INT 15 E801: 0x0000 (0K) 0x0000 (0K)
Ah.. do you have a BIOS setting called something like OS/2 compatibility ?

That's the really odd thing, I am yet to find a way to access the BIOS settings on this beast. I've tried the usual DEL, F2 and F1 with no success and there is no prompt I've ever seen to offer access to one. I do have a ZIP file that contains the last BIOS upgrade for it that was released so I'll see if I can make that bootable and see if that reveals any options.

Quoted 4 lines

Quoted 1 line
Hope life is still good in Abertawe!
This part of the world has changed rather a lot. Not sure you'd recognize half of it.

I can imagine, it's been a while since I've been back in South Wales!

Take care,
Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

Chris Samuel

author

2011-04-23 11:32 UTC #41 lore raw

Hi Alan,

Quoted 11 lines · Chris Samuel

Quoted 2 lines · Alan Cox
Ah.. do you have a BIOS setting called something like OS/2 compatibility ?
That's the really odd thing, I am yet to find a way to access the BIOS settings on this beast. I've tried the usual DEL, F2 and F1 with no success and there is no prompt I've ever seen to offer access to one. I do have a ZIP file that contains the last BIOS upgrade for it that was released so I'll see if I can make that bootable and see if that reveals any options.

OK, that ZIP file doesn't have a BIOS but it did have a BIOS configuration program. I have a "Primary Operating System" option which is currently:

UNIX, Novell, Windows NT, OS/2, Other (Multi-Processor)

The alternatives for that option are:

UNIX, Novell, Windows NT, Others (Single-Processor) DOS, OS/2

The README accompanying the ZIP says:

# Due to a PentiumPro bug the BIOS need to know if a Multi-Processor

# or Single Processor Operating System is installed to correctly
# set-up the local APIC and MP table.

The only other options that seem like they might be relevant are:

Extended Memory Above 64MB Support - Enabled
Video Shadowing - Shadowed at C000: and C400:

As regards memory it reports:

Base Memory: 640KB
Extended Memory (Contiguous): 255MB
Extended Memory (Non-contiguous): 0KB

Anything ring any bells there ?

cheers,
Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP

Chris Samuel

author

2011-04-23 13:12 UTC #42 lore raw

In reply to Alan Cox

Quoted 1 line · Alan Cox

If you boot with mem= and force the memory size what happens ?

Using memmap=636K@0 memmap=255M@1M (from just naively converting the e801 numbers from the 2.6.18 boot) it appears to get past that issue and then panic because of no root filesystem (unsurprisingly as it's based on an allnoconfig config).

Trying the same with the Debian Squeeze 2.6.32 based kernel results in it not panic'ing when unpacking the initramfs but there are many complaints about IRQ's happening and nobody caring and the system ends up shutting itself down due to timing out bringing up the root filesystem from the software RAID.

I'll be away from email for a few days now because of the Easter holidays here, but I'll catch up when I'm back.

All the best, and thanks to everyone for the help so far!

Chris

Signature · 4 lines

 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP