Overview

index 857bcad..6d92c53 100644
@@ -621,9 +621,12 @@ int npe_initialize(bd_t * bis)
 			if (ixFeatureCtrlDeviceRead() == IX_FEATURE_CTRL_DEVICE_TYPE_IXP42X) {
 				switch (ixFeatureCtrlProductIdRead() & IX_FEATURE_CTRL_SILICON_STEPPING_MASK) {
 				case IX_FEATURE_CTRL_SILICON_TYPE_B0:
+				default: /* newer than B0 */
 					/*
-					 * If it is B0 Silicon, we only enable port when its corresponding
-					 * Eth Coprocessor is available.
+					 * If it is B0 or newer Silicon, we
+					 * only enable port when its
+					 * corresponding Eth Coprocessor is
+					 * available.
 					 */
 					if (ixFeatureCtrlComponentCheck(IX_FEATURECTRL_ETH0) ==
 					    IX_FEATURE_CTRL_COMPONENT_ENABLED)

index dd26af4..a9acd47 100644
@@ -30,6 +30,7 @@
 
 #include <common.h>
 #include <asm/arch/ixp425.h>
+#include <watchdog.h>
 
 /*
  *               14.7456 MHz

@@ -85,7 +86,8 @@ int serial_init (void)
 void serial_putc (const char c)
 {
 	/* wait for room in the tx FIFO on UART */
-	while ((LSR(CONFIG_SYS_IXP425_CONSOLE) & LSR_TEMT) == 0);
+	while ((LSR(CONFIG_SYS_IXP425_CONSOLE) & LSR_TEMT) == 0)
+		WATCHDOG_RESET();	/* Reset HW Watchdog, if needed */
 
 	THR(CONFIG_SYS_IXP425_CONSOLE) = c;
 

@@ -111,7 +113,8 @@ int serial_tstc (void)
  */
 int serial_getc (void)
 {
-	while (!(LSR(CONFIG_SYS_IXP425_CONSOLE) & LSR_DR));
+	while (!(LSR(CONFIG_SYS_IXP425_CONSOLE) & LSR_DR))
+		WATCHDOG_RESET();	/* Reset HW Watchdog, if needed */
 
 	return (char) RBR(CONFIG_SYS_IXP425_CONSOLE) & 0xff;
 }

index ce275e5..942845d 100644
@@ -36,8 +36,6 @@
 #include <asm/arch/ixp425.h>
 #include <asm/system.h>
 
-ulong loops_per_jiffy;
-
 static void cache_flush(void);
 
 #if defined(CONFIG_DISPLAY_CPUINFO)

@@ -51,17 +49,14 @@ int print_cpuinfo (void)
 	puts("CPU:   Intel IXP425 at ");
 	switch ((id & 0x000003f0) >> 4) {
 	case 0x1c:
-		loops_per_jiffy = 887467;
 		speed = 533;
 		break;
 
 	case 0x1d:
-		loops_per_jiffy = 666016;
 		speed = 400;
 		break;
 
 	case 0x1f:
-		loops_per_jiffy = 442901;
 		speed = 266;
 		break;
 	}

167 lines not on this page · raw message

index 2114437..5132607 100644
@@ -391,9 +391,8 @@
 #define IXP425_TIMER_REG(x) (IXP425_TIMER_BASE_PHYS+(x))
 #endif
 
-#if 0 /* test-only: also defined in npe/include/... */
-#define IXP425_OSTS	IXP425_TIMER_REG(IXP425_OSTS_OFFSET)
-#endif
+/* _B to avoid collision: also defined in npe/include/... */
+#define IXP425_OSTS_B	IXP425_TIMER_REG(IXP425_OSTS_OFFSET)
 #define IXP425_OST1	IXP425_TIMER_REG(IXP425_OST1_OFFSET)
 #define IXP425_OSRT1	IXP425_TIMER_REG(IXP425_OSRT1_OFFSET)
 #define IXP425_OST2	IXP425_TIMER_REG(IXP425_OST2_OFFSET)

index 2a84d27..c1a59f2 100644
@@ -64,6 +64,9 @@ typedef	struct	global_data {
 	unsigned long long	timer_reset_value;
 	unsigned long	lastinc;
 #endif
+#ifdef CONFIG_IXP425
+	unsigned long	timestamp;
+#endif
 	unsigned long	relocaddr;	/* Start address of U-Boot in RAM */
 	phys_size_t	ram_size;	/* RAM size */
 	unsigned long	mon_len;	/* monitor len */

index 85e3f9e..2f631b7 100644
@@ -37,49 +37,57 @@
 #include <asm/arch/ixp425.h>
 #include <asm/io.h>
 #include <miiphy.h>
+#ifdef CONFIG_PCI
+#include <pci.h>
+#include <asm/arch/ixp425pci.h>
+#endif
 
 #include "actux1_hw.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
-int board_init (void)
+int board_early_init_f(void)
+{
+	/* CS5: Debug port */
+	writel(0x9d520003, IXP425_EXP_CS5);
+	/* CS6: HwRel */
+	writel(0x81860001, IXP425_EXP_CS6);
+	/* CS7: LEDs */
+	writel(0x80900003, IXP425_EXP_CS7);
+	return 0;
+}
+
+int board_init(void)
 {
 	gd->bd->bi_arch_number = MACH_TYPE_ACTUX1;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x00000100;
 
-	GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_IORST);
+	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST);
 
-	/* Setup GPIO's for PCI INTA */
-	GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_PCI1_INTA);
-	GPIO_INT_ACT_LOW_SET (CONFIG_SYS_GPIO_PCI1_INTA);
+	/* Setup GPIOs for PCI INTA */
+	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI1_INTA);
+	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI1_INTA);
 
-	/* Setup GPIO's for 33MHz clock output */
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_PCI_CLK);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_EXTBUS_CLK);
-	*IXP425_GPIO_GPCLKR = 0x011001FF;
+	/* Setup GPIOs for 33MHz clock output */
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
+	writel(0x011001FF, IXP425_GPIO_GPCLKR);
 
-	/* CS5: Debug port */
-	*IXP425_EXP_CS5 = 0x9d520003;
-	/* CS6: HwRel */
-	*IXP425_EXP_CS6 = 0x81860001;
-	/* CS7: LEDs */
-	*IXP425_EXP_CS7 = 0x80900003;
-
-	udelay (533);
-	GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_IORST);
+	udelay(533);
+	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
 
-	ACTUX1_LED1 (2);
-	ACTUX1_LED2 (2);
-	ACTUX1_LED3 (0);
-	ACTUX1_LED4 (0);
-	ACTUX1_LED5 (0);
-	ACTUX1_LED6 (0);
-	ACTUX1_LED7 (0);
+	ACTUX1_LED1(2);
+	ACTUX1_LED2(2);
+	ACTUX1_LED3(0);
+	ACTUX1_LED4(0);
+	ACTUX1_LED5(0);
+	ACTUX1_LED6(0);
+	ACTUX1_LED7(0);
 
-	ACTUX1_HS (ACTUX1_HS_DCD);
+	ACTUX1_HS(ACTUX1_HS_DCD);
 
 	return 0;
 }

@@ -87,21 +95,21 @@ int board_init (void)
 /*
  * Check Board Identity
  */
-int checkboard (void)
+int checkboard(void)
 {
 	char buf[64];
 	int i = getenv_f("serial#", buf, sizeof(buf));
 
-	puts ("Board: AcTux-1 rev.");
-	putc (ACTUX1_BOARDREL + 'A' - 1);
+	puts("Board: AcTux-1 rev.");
+	putc(ACTUX1_BOARDREL + 'A' - 1);
 
 	if (i > 0) {
 		puts(", serial# ");
 		puts(buf);
 	}
-	putc ('\n');
+	putc('\n');
 
-	return (0);
+	return 0;
 }
 
 /*************************************************************************

@@ -110,39 +118,36 @@ int checkboard (void)
  * 1 = Rev. A
  * 2 = Rev. B
  *************************************************************************/
-u32 get_board_rev (void)
+u32 get_board_rev(void)
 {
 	return ACTUX1_BOARDREL;
 }
 
-int dram_init (void)
+int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
-	return (0);
+	gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
+	return 0;
 }
 
-#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
-extern struct pci_controller hose;
-extern void pci_ixp_init (struct pci_controller *hose);
 
-void pci_init_board (void)
+#ifdef CONFIG_PCI
+struct pci_controller hose;
+
+void pci_init_board(void)
 {
-	extern void pci_ixp_init (struct pci_controller *hose);
-	pci_ixp_init (&hose);
+	pci_ixp_init(&hose);
 }
 #endif
 
-void reset_phy (void)
+void reset_phy(void)
 {
 	u16 id1, id2;
 
 	/* initialize the PHY */
-	miiphy_reset ("NPE0", CONFIG_PHY_ADDR);
+	miiphy_reset("NPE0", CONFIG_PHY_ADDR);
 
-	miiphy_read ("NPE0", CONFIG_PHY_ADDR, MII_PHYSID1, &id1);
-	miiphy_read ("NPE0", CONFIG_PHY_ADDR, MII_PHYSID2, &id2);
+	miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID1, &id1);
+	miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID2, &id2);
 
 	id2 &= 0xFFF0;		/* mask out revision bits */
 

@@ -153,9 +158,9 @@ void reset_phy (void)
 		 * LED2 (unused) = LINK,
 		 * LED3(red) = Coll
 		 */
-		miiphy_write ("NPE0", CONFIG_PHY_ADDR, 20, 0xD432);
+		miiphy_write("NPE0", CONFIG_PHY_ADDR, 20, 0xD432);
 	} else if (id1 == 0x143 && id2 == 0xbc30) {
 		/* BCM5241: default values are OK */
 	} else
-		printf ("unknown ethernet PHY ID: %x %x\n", id1, id2);
+		printf("unknown ethernet PHY ID: %x %x\n", id1, id2);
 }

165 lines not on this page · raw message

index 0d67f80..9040a09 100644
@@ -43,50 +43,55 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-int board_init (void)
+int board_early_init_f(void)
+{
+	/* CS1: IPAC-X */
+	writel(0x94d10013, IXP425_EXP_CS1);
+	/* CS5: Debug port */
+	writel(0x9d520003, IXP425_EXP_CS5);
+	/* CS6: HW release register */
+	writel(0x81860001, IXP425_EXP_CS6);
+	/* CS7: LEDs */
+	writel(0x80900003, IXP425_EXP_CS7);
+
+	return 0;
+}
+
+int board_init(void)
 {
 	gd->bd->bi_arch_number = MACH_TYPE_ACTUX2;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x00000100;
 
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_ETHRST);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_DSR);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_DCD);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_ETHRST);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DSR);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DCD);
 
-	GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_ETHRST);
+	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
+	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_ETHRST);
 
-	GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_DSR);
-	GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_DCD);
+	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DSR);
+	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DCD);
 
-	/* Setup GPIO's for Interrupt inputs */
-	GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_DBGINT);
-	GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_ETHINT);
+	/* Setup GPIOs for Interrupt inputs */
+	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_DBGINT);
+	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_ETHINT);
 
-	/* Setup GPIO's for 33MHz clock output */
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_PCI_CLK);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_EXTBUS_CLK);
-	*IXP425_GPIO_GPCLKR = 0x011001FF;
+	/* Setup GPIOs for 33MHz clock output */
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
+	writel(0x011001FF, IXP425_GPIO_GPCLKR);
 
-	/* CS1: IPAC-X */
-	*IXP425_EXP_CS1 = 0x94d10013;
-	/* CS5: Debug port */
-	*IXP425_EXP_CS5 = 0x9d520003;
-	/* CS6: HW release register */
-	*IXP425_EXP_CS6 = 0x81860001;
-	/* CS7: LEDs */
-	*IXP425_EXP_CS7 = 0x80900003;
+	udelay(533);
+	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
+	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_ETHRST);
 
-	udelay (533);
-	GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_ETHRST);
-
-	ACTUX2_LED1 (1);
-	ACTUX2_LED2 (0);
-	ACTUX2_LED3 (0);
-	ACTUX2_LED4 (0);
+	ACTUX2_LED1(1);
+	ACTUX2_LED2(0);
+	ACTUX2_LED3(0);
+	ACTUX2_LED4(0);
 
 	return 0;
 }

@@ -94,29 +99,27 @@ int board_init (void)
 /*
  * Check Board Identity
  */
-int checkboard (void)
+int checkboard(void)
 {
 	char buf[64];
 	int i = getenv_f("serial#", buf, sizeof(buf));
 
-	puts ("Board: AcTux-2 rev.");
-	putc (ACTUX2_BOARDREL + 'A' - 1);
+	puts("Board: AcTux-2 rev.");
+	putc(ACTUX2_BOARDREL + 'A' - 1);
 
 	if (i > 0) {
 		puts(", serial# ");
 		puts(buf);
 	}
-	putc ('\n');
+	putc('\n');
 
-	return (0);
+	return 0;
 }
 
-int dram_init (void)
+int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
-	return (0);
+	gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
+	return 0;
 }
 
 /*************************************************************************

@@ -125,13 +128,13 @@ int dram_init (void)
  * 1 = Rev. A
  * 2 = Rev. B
  *************************************************************************/
-u32 get_board_rev (void)
+u32 get_board_rev(void)
 {
 	return ACTUX2_BOARDREL;
 }
 
-void reset_phy (void)
+void reset_phy(void)
 {
 	/* init IcPlus IP175C ethernet switch to native IP175C mode */
-	miiphy_write ("NPE0", 29, 31, 0x175C);
+	miiphy_write("NPE0", 29, 31, 0x175C);
 }

index 8ab3b19..eca814b 100644
@@ -37,12 +37,12 @@
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_BOOTDELAY		5
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_BOARD_EARLY_INIT_F	1
+#define CONFIG_SYS_LDSCRIPT	"board/actux2/u-boot.lds"
 
 /***************************************************************
  * U-boot generic defines start here.
  ***************************************************************/
-#undef CONFIG_USE_IRQ
-
 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN			(CONFIG_ENV_SIZE + 128*1024)
 

@@ -84,8 +84,9 @@
 #define CONFIG_SYS_MEMTEST_START		0x00400000
 #define CONFIG_SYS_MEMTEST_END			0x00800000
 
-/* spec says 66.666 MHz, but it appears to be 33 */
-#define CONFIG_SYS_HZ				3333333
+/* timer clock - 2* OSC_IN system clock */
+#define CONFIG_IXP425_TIMER_CLK                 66666666
+#define CONFIG_SYS_HZ				1000
 
 /* default load address */
 #define CONFIG_SYS_LOAD_ADDR			0x00010000

@@ -100,10 +101,6 @@
  * The stack sizes are set up in start.S using the settings below
  */
 #define CONFIG_STACKSIZE		(128*1024)	/* regular stack */
-#ifdef CONFIG_USE_IRQ
-# define CONFIG_STACKSIZE_IRQ		(4*1024)	/* IRQ stack */
-# define CONFIG_STACKSIZE_FIQ		(4*1024)	/* FIQ stack */
-#endif
 
 /* Expansion bus settings */
 #define CONFIG_SYS_EXP_CS0			0xbd113042

@@ -111,7 +108,7 @@
 /* SDRAM settings */
 #define CONFIG_NR_DRAM_BANKS		1
 #define PHYS_SDRAM_1			0x00000000
-#define CONFIG_SYS_DRAM_BASE			0x00000000
+#define CONFIG_SYS_SDRAM_BASE			0x00000000
 
 /* 16MB SDRAM */
 #define CONFIG_SYS_SDR_CONFIG			0x3A

@@ -121,6 +118,7 @@
 #define CONFIG_SYS_DRAM_SIZE			0x01000000
 
 /* FLASH organization */
+#define CONFIG_SYS_TEXT_BASE		0x50000000
 #define CONFIG_SYS_MAX_FLASH_BANKS		1
 /* max number of sectors on one chip */
 #define CONFIG_SYS_MAX_FLASH_SECT		140

@@ -130,6 +128,7 @@
 #define CONFIG_SYS_FLASH_BASE			PHYS_FLASH_1
 #define CONFIG_SYS_MONITOR_BASE		PHYS_FLASH_1
 #define CONFIG_SYS_MONITOR_LEN			(256 << 10)
+#define CONFIG_BOARD_SIZE_LIMIT			262144
 
 /* Use common CFI driver */
 #define CONFIG_SYS_FLASH_CFI

@@ -149,6 +148,11 @@
 #define	CONFIG_PHY_ADDR			0x00
 /* MII PHY management */
 #define CONFIG_MII			1
+/* fixed-speed switch without standard PHY registers on MII */
+#define CONFIG_MII_NPE0_FIXEDLINK       1
+#define CONFIG_MII_NPE0_SPEED           100
+#define CONFIG_MII_NPE0_FULLDUPLEX      1
+
 /* Number of ethernet rx buffers & descriptors */
 #define CONFIG_SYS_RX_ETH_BUFFER		16
 #define CONFIG_RESET_PHY_R		1

@@ -183,13 +187,15 @@
 	"npe_ucode=50040000\0"						\
 	"mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \
 	"kerneladdr=50050000\0"						\
+	"kernelfile=actux2/uImage\0"					\
+	"rootfile=actux2/rootfs\0"					\
 	"rootaddr=50170000\0"						\
 	"loadaddr=10000\0"						\
 	"updateboot_ser=mw.b 10000 ff 40000;"				\
 	" loady ${loadaddr};"						\
 	" run eraseboot writeboot\0"					\
 	"updateboot_net=mw.b 10000 ff 40000;"				\
-	" tftp ${loadaddr} u-boot.bin;"					\
+	" tftp ${loadaddr} actux2/u-boot.bin;"				\
 	" run eraseboot writeboot\0"					\
 	"eraseboot=protect off 50000000 50003fff;"			\
 	" protect off 50006000 5003ffff;"				\

@@ -197,8 +203,9 @@
 	" erase 50006000 5003ffff\0"					\
 	"writeboot=cp.b 10000 50000000 4000;"				\
 	" cp.b 16000 50006000 3a000\0"					\
-	"eraseenv=protect off 50004000 50005fff;"			\
-	" erase 50004000 50005fff\0"					\
+	"updateucode=loady;"						\
+	" era ${npe_ucode} +${filesize};"				\
+	" cp.b ${loadaddr} ${npe_ucode} ${filesize}\0"			\
 	"updateroot=tftp ${loadaddr} ${rootfile};"			\
 	" era ${rootaddr} +${filesize};"				\
 	" cp.b ${loadaddr} ${rootaddr} ${filesize}\0"			\

@@ -217,4 +224,8 @@
 	" tftpboot ${loadaddr} ${kernelfile};"				\
 	" bootm\0"
 
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_INIT_SP_ADDR						\
+	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
 #endif /* __CONFIG_H */

index bace254..64e5215 100644
@@ -36,72 +36,76 @@
 #include <malloc.h>
 #include <asm/arch/ixp425.h>
 #include <asm/io.h>
-
 #include <miiphy.h>
-
 #include "actux3_hw.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
-int board_init (void)
+int board_early_init_f(void)
+{
+	/* CS1: IPAC-X */
+	writel(0x94d10013, IXP425_EXP_CS1);
+	/* CS5: Debug port */
+	writel(0x9d520003, IXP425_EXP_CS5);
+	/* CS6: Release/Option register */
+	writel(0x81860001, IXP425_EXP_CS6);
+	/* CS7: LEDs */
+	writel(0x80900003, IXP425_EXP_CS7);
+
+	return 0;
+}
+
+int board_init(void)
 {
 	gd->bd->bi_arch_number = MACH_TYPE_ACTUX3;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x00000100;
 
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_ETHRST);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_DSR);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_DCD);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_LED5_GN);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_LED6_RT);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_LED6_GN);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_ETHRST);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DSR);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DCD);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED5_GN);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED6_RT);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED6_GN);
 
-	GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_ETHRST);
+	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
+	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_ETHRST);
 
-	GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_DSR);
-	GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_DCD);
+	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DSR);
+	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DCD);
 
-	GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_LED5_GN);
-	GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_LED6_RT);
-	GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_LED6_GN);
+	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED5_GN);
+	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED6_RT);
+	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED6_GN);
 
 	/*
 	 * Setup GPIO's for Interrupt inputs
 	 */
-	GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_DBGINT);
-	GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_ETHINT);
+	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_DBGINT);
+	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_ETHINT);
 
 	/*
 	 * Setup GPIO's for 33MHz clock output
 	 */
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_PCI_CLK);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_EXTBUS_CLK);
-	*IXP425_GPIO_GPCLKR = 0x011001FF;
-
-	/* CS1: IPAC-X */
-	*IXP425_EXP_CS1 = 0x94d10013;
-	/* CS5: Debug port */
-	*IXP425_EXP_CS5 = 0x9d520003;
-	/* CS6: Release/Option register */
-	*IXP425_EXP_CS6 = 0x81860001;
-	/* CS7: LEDs */
-	*IXP425_EXP_CS7 = 0x80900003;
-
-	udelay (533);
-	GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_ETHRST);
-
-	ACTUX3_LED1_RT (1);
-	ACTUX3_LED1_GN (0);
-	ACTUX3_LED2_RT (0);
-	ACTUX3_LED2_GN (0);
-	ACTUX3_LED3_RT (0);
-	ACTUX3_LED3_GN (0);
-	ACTUX3_LED4_GN (0);
-	ACTUX3_LED5_RT (0);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
+	writel(0x011001FF, IXP425_GPIO_GPCLKR);
+
+	/* we need a minimum PCI reset pulse width after enabling the clock */
+	udelay(533);
+	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
+	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_ETHRST);
+
+	ACTUX3_LED1_RT(1);
+	ACTUX3_LED1_GN(0);
+	ACTUX3_LED2_RT(0);
+	ACTUX3_LED2_GN(0);
+	ACTUX3_LED3_RT(0);
+	ACTUX3_LED3_GN(0);
+	ACTUX3_LED4_GN(0);
+	ACTUX3_LED5_RT(0);
 
 	return 0;
 }

@@ -109,21 +113,21 @@ int board_init (void)
 /*
  * Check Board Identity
  */
-int checkboard (void)
+int checkboard(void)
 {
 	char buf[64];
 	int i = getenv_f("serial#", buf, sizeof(buf));
 
-	puts ("Board: AcTux-3 rev.");
-	putc (ACTUX3_BOARDREL + 'A' - 1);
+	puts("Board: AcTux-3 rev.");
+	putc(ACTUX3_BOARDREL + 'A' - 1);
 
 	if (i > 0) {
 		puts (", serial# ");
 		puts (buf);
 	}
-	putc ('\n');
+	putc('\n');
 
-	return (0);
+	return 0;
 }
 
 /*************************************************************************

@@ -132,34 +136,32 @@ int checkboard (void)
  * 1 = Rev. A
  * 2 = Rev. B
  *************************************************************************/
-u32 get_board_rev (void)
+u32 get_board_rev(void)
 {
 	return ACTUX3_BOARDREL;
 }
 
-int dram_init (void)
+int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
-	return (0);
+	gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
+	return 0;
 }
 
-void reset_phy (void)
+void reset_phy(void)
 {
 	int i;
 
 	/* initialize the PHY */
-	miiphy_reset ("NPE0", CONFIG_PHY_ADDR);
+	miiphy_reset("NPE0", CONFIG_PHY_ADDR);
 
 	/* all LED outputs = Link/Act */
-	miiphy_write ("NPE0", CONFIG_PHY_ADDR, 0x16, 0x0AAA);
+	miiphy_write("NPE0", CONFIG_PHY_ADDR, 0x16, 0x0AAA);
 
 	/*
 	 * The Marvell 88E6060 switch comes up with all ports disabled.
 	 * set all ethernet switch ports to forwarding state
 	*/
 	for (i = 1; i <= 5; i++)
-		miiphy_write ("NPE0", CONFIG_PHY_ADDR + 8 + i, 0x04, 0x03);
+		miiphy_write("NPE0", CONFIG_PHY_ADDR + 8 + i, 0x04, 0x03);
 
 }

index 91987cb..c103312 100644
@@ -37,12 +37,12 @@
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_BOOTDELAY		3
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_BOARD_EARLY_INIT_F	1
+#define CONFIG_SYS_LDSCRIPT	"board/actux3/u-boot.lds"
 
 /***************************************************************
  * U-boot generic defines start here.
  ***************************************************************/
-#undef CONFIG_USE_IRQ
-
 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN			(CONFIG_ENV_SIZE + 128*1024)
 

@@ -82,8 +82,9 @@
 #define CONFIG_SYS_MEMTEST_START		0x00400000
 #define CONFIG_SYS_MEMTEST_END			0x00800000
 
-/* spec says 66.666 MHz, but it appears to be 33 */
-#define CONFIG_SYS_HZ				3333333
+/* timer clock - 2* OSC_IN system clock */
+#define CONFIG_IXP425_TIMER_CLK                 66666666
+#define CONFIG_SYS_HZ				1000
 
 /* default load address */
 #define CONFIG_SYS_LOAD_ADDR			0x00010000

@@ -99,10 +100,6 @@
  * The stack sizes are set up in start.S using the settings below
  */
 #define CONFIG_STACKSIZE		(128*1024)	/* regular stack */
-#ifdef CONFIG_USE_IRQ
-# define CONFIG_STACKSIZE_IRQ		(4*1024)	/* IRQ stack */
-# define CONFIG_STACKSIZE_FIQ		(4*1024)	/* FIQ stack */
-#endif
 
 /* Expansion bus settings */
 #define CONFIG_SYS_EXP_CS0			0xbd113442

@@ -110,7 +107,7 @@
 /* SDRAM settings */
 #define CONFIG_NR_DRAM_BANKS		1
 #define PHYS_SDRAM_1			0x00000000
-#define CONFIG_SYS_DRAM_BASE			0x00000000
+#define CONFIG_SYS_SDRAM_BASE			0x00000000
 
 /* 16MB SDRAM */
 #define CONFIG_SYS_SDR_CONFIG			0x3A

@@ -120,6 +117,7 @@
 #define CONFIG_SYS_DRAM_SIZE			0x01000000
 
 /* FLASH organization */
+#define CONFIG_SYS_TEXT_BASE		0x50000000
 #define CONFIG_SYS_MAX_FLASH_BANKS		1
 /* max number of sectors on one chip */
 #define CONFIG_SYS_MAX_FLASH_SECT		140

@@ -129,6 +127,7 @@
 #define CONFIG_SYS_FLASH_BASE			PHYS_FLASH_1
 #define CONFIG_SYS_MONITOR_BASE		PHYS_FLASH_1
 #define CONFIG_SYS_MONITOR_LEN			(256 << 10)
+#define CONFIG_BOARD_SIZE_LIMIT			262144
 
 /* Use common CFI driver */
 #define CONFIG_SYS_FLASH_CFI

@@ -149,6 +148,11 @@
 #define	CONFIG_PHY_ADDR			0x10
 /* MII PHY management */
 #define CONFIG_MII			1
+/* fixed-speed switch without standard PHY registers on MII */
+#define CONFIG_MII_NPE0_FIXEDLINK       1
+#define CONFIG_MII_NPE0_SPEED           100
+#define CONFIG_MII_NPE0_FULLDUPLEX      1
+
 /* Number of ethernet rx buffers & descriptors */
 #define CONFIG_SYS_RX_ETH_BUFFER		16
 #define CONFIG_RESET_PHY_R		1

@@ -183,13 +187,15 @@
 	"npe_ucode=50040000\0"						\
 	"mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \
 	"kerneladdr=50050000\0"						\
+	"kernelfile=actux3/uImage\0"					\
+	"rootfile=actux3/rootfs\0"					\
 	"rootaddr=50170000\0"						\
 	"loadaddr=10000\0"						\
 	"updateboot_ser=mw.b 10000 ff 40000;"				\
 	" loady ${loadaddr};"						\
 	" run eraseboot writeboot\0"					\
 	"updateboot_net=mw.b 10000 ff 40000;"				\
-	" tftp ${loadaddr} u-boot.bin;"					\
+	" tftp ${loadaddr} actux3/u-boot.bin;"				\
 	" run eraseboot writeboot\0"					\
 	"eraseboot=protect off 50000000 50003fff;"			\
 	" protect off 50006000 5003ffff;"				\

@@ -197,8 +203,9 @@
 	" erase 50006000 5003ffff\0"					\
 	"writeboot=cp.b 10000 50000000 4000;"				\
 	" cp.b 16000 50006000 3a000\0"					\
-	"eraseenv=protect off 50004000 50005fff;"			\
-	" erase 50004000 50005fff\0"					\
+	"updateucode=loady;"						\
+	" era ${npe_ucode} +${filesize};"				\
+	" cp.b ${loadaddr} ${npe_ucode} ${filesize}\0"			\
 	"updateroot=tftp ${loadaddr} ${rootfile};"			\
 	" era ${rootaddr} +${filesize};"				\
 	" cp.b ${loadaddr} ${rootaddr} ${filesize}\0"			\

@@ -209,7 +216,7 @@
 	" rootfstype=squashfs,jffs2 init=/etc/preinit\0"		\
 	"netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3"	\
 	" rootfstype=squashfs,jffs2 init=/etc/preinit\0"		\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
+	"addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0" \
 	"addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0"	\
 	"boot_flash=run flashargs addtty addeth;"			\
 	" bootm ${kerneladdr}\0"					\

@@ -217,4 +224,8 @@
 	" tftpboot ${loadaddr} ${kernelfile};"				\
 	" bootm\0"
 
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_INIT_SP_ADDR						\
+	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
 #endif /* __CONFIG_H */

index f373b58..d20d881 100644
@@ -35,92 +35,107 @@
 #include <command.h>
 #include <malloc.h>
 #include <asm/arch/ixp425.h>
-
+#include <asm/io.h>
 #include <miiphy.h>
+#ifdef CONFIG_PCI
+#include <pci.h>
+#include <asm/arch/ixp425pci.h>
+#endif
 
 #include "actux4_hw.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
-int board_init (void)
+int board_early_init_f(void)
+{
+	writel(0xbd113c42, IXP425_EXP_CS1);
+	return 0;
+}
+
+int board_init(void)
 {
 	gd->bd->bi_arch_number = MACH_TYPE_ACTUX4;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x00000100;
 
-	GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_nPWRON);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_nPWRON);
+	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_nPWRON);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_nPWRON);
 
-	GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_IORST);
+	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST);
 
 	/* led not populated on board*/
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_LED3);
-	GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_LED3);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED3);
+	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED3);
 
 	/* middle LED */
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_LED2);
-	GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_LED2);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED2);
+	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED2);
 
 	/* right LED */
 	/* weak pulldown = LED weak on */
-	GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_LED1);
-	GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_LED1);
+	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_LED1);
+	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED1);
 
 	/* Setup GPIO's for Interrupt inputs */
-	GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_USBINTA);
-	GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_USBINTB);
-	GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_USBINTC);
-	GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_RTCINT);
-	GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_PCI_INTA);
-	GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_PCI_INTB);
-
-	GPIO_INT_ACT_LOW_SET (CONFIG_SYS_GPIO_USBINTA);
-	GPIO_INT_ACT_LOW_SET (CONFIG_SYS_GPIO_USBINTB);
-	GPIO_INT_ACT_LOW_SET (CONFIG_SYS_GPIO_USBINTC);
-	GPIO_INT_ACT_LOW_SET (CONFIG_SYS_GPIO_RTCINT);
-	GPIO_INT_ACT_LOW_SET (CONFIG_SYS_GPIO_PCI_INTA);
-	GPIO_INT_ACT_LOW_SET (CONFIG_SYS_GPIO_PCI_INTB);
+	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTA);
+	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTB);
+	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTC);
+	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_RTCINT);
+	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTA);
+	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTB);
+
+	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTA);
+	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTB);
+	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTC);
+	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_RTCINT);
+	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTA);
+	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTB);
 
 	/* Setup GPIO's for 33MHz clock output */
-	*IXP425_GPIO_GPCLKR = 0x011001FF;
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_EXTBUS_CLK);
-	GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_PCI_CLK);
-
-	*IXP425_EXP_CS1 = 0xbd113c42;
+	writel(0x011001FF, IXP425_GPIO_GPCLKR);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
+	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
 
-	udelay (10000);
-	GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_IORST);
-	udelay (10000);
-	GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_IORST);
-	udelay (10000);
-	GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_IORST);
+	udelay(10000);
+	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
+	udelay(10000);
+	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
+	udelay(10000);
+	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
 
 	return 0;
 }
 
 /* Check Board Identity */
-int checkboard (void)
+int checkboard(void)
 {
-	puts ("Board: AcTux-4\n");
-	return (0);
+	puts("Board: AcTux-4\n");
+	return 0;
 }
 
-int dram_init (void)
+int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+	gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
+	return 0;
+}
 
-	return (0);
+#ifdef CONFIG_PCI
+struct pci_controller hose;
+
+void pci_init_board(void)
+{
+	pci_ixp_init(&hose);
 }
+#endif
 
 /*
  * Hardcoded flash setup:
  * Flash 0 is a non-CFI SST 39VF020 flash, 8 bit flash / 8 bit bus.
  * Flash 1 is an Intel *16 flash using the CFI driver.
  */
-ulong board_flash_get_legacy (ulong base, int banknum, flash_info_t * info)
+ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
 {
 	if (banknum == 0) {	/* non-CFI boot flash */
 		info->portwidth = 1;

index 6718921..190de5a 100644
@@ -37,12 +37,11 @@
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_BOOTDELAY		3
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_BOARD_EARLY_INIT_F	1
 
 /***************************************************************
  * U-boot generic defines start here.
  ***************************************************************/
-#undef CONFIG_USE_IRQ
-
 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN			(CONFIG_ENV_SIZE + 128*1024)
 

@@ -54,6 +53,15 @@
 
 #define CONFIG_CMD_ELF
 
+#define CONFIG_PCI
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_PCI_PNP
+#define CONFIG_IXP_PCI
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_CMD_PCI_ENUM
+#endif
+
 #define CONFIG_BOOTCOMMAND		"run boot_flash"
 /* enable passing of ATAGs */
 #define CONFIG_CMDLINE_TAG		1

@@ -81,8 +89,9 @@
 #define CONFIG_SYS_MEMTEST_START		0x00400000
 #define CONFIG_SYS_MEMTEST_END			0x00800000
 
-/* spec says 66.666 MHz, but it appears to be 33 */
-#define CONFIG_SYS_HZ				3333333
+/* timer clock - 2* OSC_IN system clock */
+#define CONFIG_IXP425_TIMER_CLK                 66000000
+#define CONFIG_SYS_HZ				1000
 
 /* default load address */
 #define CONFIG_SYS_LOAD_ADDR			0x00010000

@@ -97,10 +106,6 @@
  * The stack sizes are set up in start.S using the settings below
  */
 #define CONFIG_STACKSIZE		(128*1024)	/* regular stack */
-#ifdef CONFIG_USE_IRQ
-# define CONFIG_STACKSIZE_IRQ		(4*1024)	/* IRQ stack */
-# define CONFIG_STACKSIZE_FIQ		(4*1024)	/* FIQ stack */
-#endif
 
 /* Expansion bus settings */
 #define CONFIG_SYS_EXP_CS0			0xbd113003

@@ -108,7 +113,7 @@
 /* SDRAM settings */
 #define CONFIG_NR_DRAM_BANKS		1
 #define PHYS_SDRAM_1			0x00000000
-#define CONFIG_SYS_DRAM_BASE			0x00000000
+#define CONFIG_SYS_SDRAM_BASE			0x00000000
 
 /* 32MB SDRAM */
 #define CONFIG_SYS_SDR_CONFIG			0x18

@@ -118,6 +123,7 @@
 #define CONFIG_SYS_DRAM_SIZE			0x02000000
 
 /* FLASH organization */
+#define CONFIG_SYS_TEXT_BASE		0x50000000
 #define CONFIG_SYS_MAX_FLASH_BANKS		2
 /* max # of sectors per chip */
 #define CONFIG_SYS_MAX_FLASH_SECT		70

@@ -128,6 +134,7 @@
 #define CONFIG_SYS_FLASH_BASE			PHYS_FLASH_1
 #define CONFIG_SYS_MONITOR_BASE		PHYS_FLASH_1
 #define CONFIG_SYS_MONITOR_LEN			(252 << 10)
+#define CONFIG_BOARD_SIZE_LIMIT			258048
 
 /* Use common CFI driver */
 #define CONFIG_SYS_FLASH_CFI

@@ -152,6 +159,7 @@
 #define	CONFIG_PHY_ADDR			0x1C
 /* MII PHY management */
 #define CONFIG_MII			1
+
 /* Number of ethernet rx buffers & descriptors */
 #define CONFIG_SYS_RX_ETH_BUFFER		16
 

@@ -180,19 +188,22 @@
 	"mtd=IXP4XX-Flash.0:252k(uboot),4k(uboot_env);"			\
 	"IXP4XX-Flash.1:128k(ucode),1280k(linux),-(root)\0"		\
 	"kerneladdr=51020000\0"						\
+	"kernelfile=actux4/uImage\0"					\
+	"rootfile=actux4/rootfs\0"					\
 	"rootaddr=51160000\0"						\
 	"loadaddr=10000\0"						\
 	"updateboot_ser=mw.b 10000 ff 40000;"				\
 	" loady ${loadaddr};"						\
 	" run eraseboot writeboot\0"					\
 	"updateboot_net=mw.b 10000 ff 40000;"				\
-	" tftp ${loadaddr} u-boot.bin;"					\
+	" tftp ${loadaddr} actux4/u-boot.bin;"					\
 	" run eraseboot writeboot\0"					\
 	"eraseboot=protect off 50000000 5003efff;"			\
 	" erase 50000000 +${filesize}\0"				\
 	"writeboot=cp.b 10000 50000000 ${filesize}\0"			\
-	"eraseenv=protect off 5003f000 5003ffff;"			\
-	" erase 5003f000 5003ffff\0"					\
+	"updateucode=loady;"						\
+	" era ${npe_ucode} +${filesize};"				\
+	" cp.b ${loadaddr} ${npe_ucode} ${filesize}\0"			\
 	"updateroot=tftp ${loadaddr} ${rootfile};"			\
 	" era ${rootaddr} +${filesize};"				\
 	" cp.b ${loadaddr} ${rootaddr} ${filesize}\0"			\

@@ -211,4 +222,8 @@
 	" tftpboot ${loadaddr} ${kernelfile};"				\
 	" bootm\0"
 
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_INIT_SP_ADDR						\
+	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
 #endif /* __CONFIG_H */

index 6d92c53..f0e02bf 100644
@@ -359,36 +359,53 @@ static int npe_init(struct eth_device *dev, bd_t * bis)
 
 	debug("%s: 1\n", __FUNCTION__);
 
-	miiphy_read (dev->name, p_npe->phy_no, MII_BMSR, &reg_short);
-
-	/*
-	 * Wait if PHY is capable of autonegotiation and autonegotiation is not complete
-	 */
-	if ((reg_short & BMSR_ANEGCAPABLE) && !(reg_short & BMSR_ANEGCOMPLETE)) {
-		puts ("Waiting for PHY auto negotiation to complete");
-		i = 0;
-		while (!(reg_short & BMSR_ANEGCOMPLETE)) {
-			/*
-			 * Timeout reached ?
-			 */
-			if (i > PHY_AUTONEGOTIATE_TIMEOUT) {
-				puts (" TIMEOUT !\n");
-				break;
-			}
+#ifdef CONFIG_MII_NPE0_FIXEDLINK
+	if (0 == p_npe->eth_id) {
+		speed = CONFIG_MII_NPE0_SPEED;
+		duplex = CONFIG_MII_NPE0_FULLDUPLEX ? FULL : HALF;
+	} else
+#endif
+#ifdef CONFIG_MII_NPE1_FIXEDLINK
+	if (1 == p_npe->eth_id) {
+		speed = CONFIG_MII_NPE1_SPEED;
+		duplex = CONFIG_MII_NPE1_FULLDUPLEX ? FULL : HALF;
+	} else
+#endif
+	{
+		miiphy_read(dev->name, p_npe->phy_no, MII_BMSR, &reg_short);
+
+		/*
+		 * Wait if PHY is capable of autonegotiation and
+		 * autonegotiation is not complete
+		 */
+		if ((reg_short & BMSR_ANEGCAPABLE) &&
+		    !(reg_short & BMSR_ANEGCOMPLETE)) {
+			puts("Waiting for PHY auto negotiation to complete");
+			i = 0;
+			while (!(reg_short & BMSR_ANEGCOMPLETE)) {
+				/*
+				 * Timeout reached ?
+				 */
+				if (i > PHY_AUTONEGOTIATE_TIMEOUT) {
+					puts(" TIMEOUT !\n");
+					break;
+				}
 
-			if ((i++ % 1000) == 0) {
-				putc ('.');
-				miiphy_read (dev->name, p_npe->phy_no, MII_BMSR, &reg_short);
+				if ((i++ % 1000) == 0) {
+					putc('.');
+					miiphy_read(dev->name, p_npe->phy_no,
+						     MII_BMSR, &reg_short);
+				}
+				udelay(1000);	/* 1 ms */
 			}
-			udelay (1000);	/* 1 ms */
+			puts(" done\n");
+			/* another 500 ms (results in faster booting) */
+			udelay(500000);
 		}
-		puts (" done\n");
-		udelay (500000);	/* another 500 ms (results in faster booting) */
+		speed = miiphy_speed(dev->name, p_npe->phy_no);
+		duplex = miiphy_duplex(dev->name, p_npe->phy_no);
 	}
 
-	speed = miiphy_speed (dev->name, p_npe->phy_no);
-	duplex = miiphy_duplex (dev->name, p_npe->phy_no);
-
 	if (p_npe->print_speed) {
 		p_npe->print_speed = 0;
 		printf ("ENET Speed is %d Mbps - %s duplex connection\n",

130 lines not on this page · raw message

47 lines not on this page · raw message

43 lines not on this page · raw message

248 lines not on this page · raw message

427 lines not on this page · raw message

206 lines not on this page · raw message

284 lines not on this page · raw message

index 637fd7d..3de0013 100644
@@ -53,9 +53,6 @@
 /*
  * Misc configuration options
  */
-#undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff	*/
-#define CONFIG_USE_IRQ          1	/* we need IRQ stuff for timer	*/
-#define CONFIG_TIMER_IRQ
 
 #define CONFIG_BOOTCOUNT_LIMIT		/* support for bootcount limit	*/
 #define CONFIG_SYS_BOOTCOUNT_ADDR	0x60003000 /* inside qmrg sram		*/

@@ -115,6 +112,7 @@
 #define CONFIG_SYS_MEMTEST_END         0x00800000      /* 4 ... 8 MB in DRAM   */
 #define CONFIG_SYS_LOAD_ADDR           0x00010000      /* default load address */
 
+#define CONFIG_IXP425_TIMER_CLK		66666666
 #define CONFIG_SYS_HZ			1000		/* decrementer freq: 1 ms ticks */
 
 						/* valid baudrates */

@@ -179,6 +177,8 @@
 #define PHYS_SDRAM_1            0x00000000 /* SDRAM Bank #1 */
 #define PHYS_SDRAM_1_SIZE       0x02000000 /* 32 MB */
 
+#define CONFIG_SYS_TEXT_BASE	0x50000000
+
 #define PHYS_FLASH_1            0x50000000 /* Flash Bank #1 */
 #define PHYS_FLASH_SIZE         0x01000000 /* 16 MB */
 #define PHYS_FLASH_BANK_SIZE    0x01000000 /* 16 MB Banks */

@@ -248,4 +248,9 @@
  */
 #define CONFIG_SYS_CACHELINE_SIZE	32
 
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_SDRAM_BASE 0
+#define CONFIG_SYS_INIT_SP_ADDR						\
+	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
 #endif  /* __CONFIG_H */

index 33fa6ee..7fe9e5b 100644
@@ -50,9 +50,6 @@
 /*
  * Misc configuration options
  */
-#define CONFIG_USE_IRQ          1	/* we need IRQ stuff for timer	*/
-#define CONFIG_TIMER_IRQ
-
 #define CONFIG_BOOTCOUNT_LIMIT		/* support for bootcount limit	*/
 #define CONFIG_SYS_BOOTCOUNT_ADDR	0x60003000 /* inside qmrg sram		*/
 

@@ -117,6 +114,7 @@
 #define CONFIG_SYS_MEMTEST_END         0x00800000      /* 4 ... 8 MB in DRAM   */
 #define CONFIG_SYS_LOAD_ADDR           0x00010000      /* default load address */
 
+#define CONFIG_IXP425_TIMER_CLK		66666666
 #define CONFIG_SYS_HZ			1000		/* decrementer freq: 1 ms ticks */
 						/* valid baudrates */
 #define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }

@@ -188,6 +186,7 @@
 #define PHYS_SDRAM_1            0x00000000 /* SDRAM Bank #1 */
 #define PHYS_SDRAM_1_SIZE       0x02000000 /* 32 MB */
 
+#define CONFIG_SYS_TEXT_BASE	       0x50000000
 #define CONFIG_SYS_FLASH_BASE          0x50000000
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
 #if defined(CONFIG_SCPU)

@@ -345,4 +344,9 @@
  */
 #define CONFIG_SYS_CACHELINE_SIZE	32
 
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_INIT_SP_ADDR        \
+	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
 #endif  /* __CONFIG_H */

index 9ea3319..acafea7 100644
@@ -22,88 +22,21 @@
  * MA 02111-1307 USA
  */
 
-#ifndef _IXP425PCI_H_
-#define _IXP425PCI_H_
+#ifndef _IXP425PCI_H
+#define _IXP425PCI_H
 
-#define TRUE	1
-#define FALSE	0
 #define OK	0
 #define ERROR	-1
-#define BOOL	int
 
-#define IXP425_PCI_MAX_BAR_PER_FUNC  6
-#define IXP425_PCI_MAX_BAR (IXP425_PCI_MAX_BAR_PER_FUNC * \
-			    IXP425_PCI_MAX_FUNC_ON_BUS)
-
-enum PciBarId
-{
-	CSR_BAR=0,
-	IO_BAR,
-	SD_BAR,
-	NO_BAR
-};
-
-/*Base address register descriptor*/
-typedef struct
-{
-	unsigned int size;
-	unsigned int address;
-} PciBar;
-
-typedef struct
-{
-	unsigned int bus;
-	unsigned int device;
-	unsigned int func;
-	unsigned int irq;
-	BOOL error;
-	unsigned short vendor_id;
-	unsigned short device_id;
-	/*We need an extra entry in this array for dummy placeholder*/
-	PciBar bar[IXP425_PCI_MAX_BAR_PER_FUNC + 1];
-} PciDevice;
+struct pci_controller;
+extern void pci_ixp_init(struct pci_controller *hose);
 
 /* Mask definitions*/
-#define IXP425_PCI_TOP_WORD_OF_LONG_MASK	0xffff0000
-#define IXP425_PCI_TOP_BYTE_OF_LONG_MASK	0xff000000
-#define IXP425_PCI_BOTTOM_WORD_OF_LONG_MASK	0x0000ffff
-#define IXP425_PCI_BOTTOM_TRIBYTES_OF_LONG_MASK 0x00ffffff
 #define IXP425_PCI_BOTTOM_NIBBLE_OF_LONG_MASK	0x0000000f
-#define IXP425_PCI_MAX_UINT32			0xffffffff
-
-
-#define IXP425_PCI_BAR_QUERY			0xffffffff
-
-#define IXP425_PCI_BAR_MEM_BASE 0x100000
-#define IXP425_PCI_BAR_IO_BASE	0x000000
-
-/*define the maximum number of bus segments - we support a single segment*/
-#define IXP425_PCI_MAX_BUS  1
-/*define the maximum number of cards per bus segment*/
-#define IXP425_PCI_MAX_DEV  4
-/*define the maximum number of functions per device*/
-#define IXP425_PCI_MAX_FUNC 8
-/* define the maximum number of separate functions that we can
-   potentially have on the bus*/
-#define IXP425_PCI_MAX_FUNC_ON_BUS (1+ IXP425_PCI_MAX_FUNC *	\
-				    IXP425_PCI_MAX_DEV *	\
-				    IXP425_PCI_MAX_BUS)
-/*define the maximum number of BARs per function*/
-#define IXP425_PCI_MAX_BAR_PER_FUNC  6
-#define IXP425_PCI_MAX_BAR (IXP425_PCI_MAX_BAR_PER_FUNC *	\
-			    IXP425_PCI_MAX_FUNC_ON_BUS)
 
 #define PCI_NP_CBE_BESL	 (4)
 #define PCI_NP_AD_FUNCSL (8)
 
-#define REG_WRITE(b,o,v) (*(volatile unsigned int*)((b+o))=(v))
-#define REG_READ(b,o,v)	 ((v)=(*(volatile unsigned int*)((b+o))))
-
-#define PCI_DELAY	500
-#define USEC_LOOP_COUNT 533
-#define PCI_SETTLE_USEC 200
-#define PCI_MIN_RESET_ASSERT_USEC 2000
-
 /*Register addressing definitions for PCI controller configuration
   and status registers*/
 

@@ -150,28 +83,6 @@ typedef struct
 #define NP_CMD_CONFIGWRITE (0xb)
 */
 
-/*define the default setting of the AHB memory base reg*/
-#define IXP425_PCI_AHBMEMBASE_DEFAULT 0x00010203
-#define IXP425_PCI_AHBIOBASE_DEFAULT  0x0
-#define IXP425_PCI_PCIMEMBASE_DEFAULT 0x0
-
-/*define the default settings for the controller's BARs*/
-#ifdef IXP425_PCI_SIMPLE_MAPPING
-#define IXP425_PCI_BAR_0_DEFAULT 0x00000000
-#define IXP425_PCI_BAR_1_DEFAULT 0x01000000
-#define IXP425_PCI_BAR_2_DEFAULT 0x02000000
-#define IXP425_PCI_BAR_3_DEFAULT 0x03000000
-#define IXP425_PCI_BAR_4_DEFAULT 0x00000000
-#define IXP425_PCI_BAR_5_DEFAULT 0x00000000
-#else
-#define IXP425_PCI_BAR_0_DEFAULT 0x40000000
-#define IXP425_PCI_BAR_1_DEFAULT 0x41000000
-#define IXP425_PCI_BAR_2_DEFAULT 0x42000000
-#define IXP425_PCI_BAR_3_DEFAULT 0x43000000
-#define IXP425_PCI_BAR_4_DEFAULT 0x00000000
-#define IXP425_PCI_BAR_5_DEFAULT 0x00000000
-#endif
-
 /*Configuration Port register bit definitions*/
 #define PCI_CRP_WRITE BIT(16)
 

@@ -228,17 +139,6 @@ typedef struct
 #define PCI_CFG_SPECIAL_USE	0x41
 #define PCI_CFG_MODE		0x43
 
-/*Specify the initial command we send to PCI devices*/
-#define INITIAL_PCI_CMD (PCI_CMD_IO_ENABLE	   \
-			 | PCI_CMD_MEM_ENABLE	   \
-			 | PCI_CMD_MASTER_ENABLE   \
-			 | PCI_CMD_WI_ENABLE)
-
-/*define the sub vendor and subsystem to be used */
-#define IXP425_PCI_SUB_VENDOR_SYSTEM 0x00000000
-
-#define PCI_IRQ_LINES		4
-
 #define PCI_CMD_IO_ENABLE	0x0001	/* IO access enable */
 #define PCI_CMD_MEM_ENABLE	0x0002	/* memory access enable */
 #define PCI_CMD_MASTER_ENABLE	0x0004	/* bus master enable */

@@ -287,26 +187,4 @@ typedef struct
 #define PCI_DMACTRL_PADC1   BIT(14)
 #define PCI_DMACTRL_PADE1   BIT(15)
 
-/* GPIO related register */
-#undef IXP425_GPIO_GPOUTR
-#undef IXP425_GPIO_GPOER
-#undef IXP425_GPIO_GPINR
-#undef IXP425_GPIO_GPISR
-#undef IXP425_GPIO_GPIT1R
-#undef IXP425_GPIO_GPIT2R
-#undef IXP425_GPIO_GPCLKR
-
-#define IXP425_GPIO_GPOUTR	0xC8004000
-#define IXP425_GPIO_GPOER	0xC8004004
-#define IXP425_GPIO_GPINR	0xC8004008
-#define IXP425_GPIO_GPISR	0xC800400C
-#define IXP425_GPIO_GPIT1R	0xC8004010
-#define IXP425_GPIO_GPIT2R	0xC8004014
-#define IXP425_GPIO_GPCLKR	0xC8004018
-
-#define READ_GPIO_REG(addr,val) \
-		(val) = *((volatile int *)(addr));
-#define WRITE_GPIO_REG(addr,val) \
-		*((volatile int *)(addr)) = (val);
-
 #endif

index cdfc4fb..1a0b14c 100644
@@ -50,7 +50,6 @@ PCI_HOSE_OP(write, byte, u8)
 PCI_HOSE_OP(write, word, u16)
 PCI_HOSE_OP(write, dword, u32)
 
-#ifndef CONFIG_IXP425
 #define PCI_OP(rw, size, type, error_code)				\
 int pci_##rw##_config_##size(pci_dev_t dev, int offset, type value)	\
 {									\

@@ -71,7 +70,6 @@ PCI_OP(read, dword, u32 *, *value = 0xffffffff)
 PCI_OP(write, byte, u8, )
 PCI_OP(write, word, u16, )
 PCI_OP(write, dword, u32, )
-#endif	/* CONFIG_IXP425 */
 
 #define PCI_READ_VIA_DWORD_OP(size, type, off_mask)			\
 int pci_hose_read_config_##size##_via_dword(struct pci_controller *hose,\

@@ -190,7 +188,6 @@ int pci_last_busno(void)
 	return hose->last_busno;
 }
 
-#ifndef CONFIG_IXP425
 pci_dev_t pci_find_devices(struct pci_device_id *ids, int index)
 {
 	struct pci_controller * hose;

@@ -246,7 +243,6 @@ pci_dev_t pci_find_devices(struct pci_device_id *ids, int index)
 
 	return (-1);
 }
-#endif	/* CONFIG_IXP425 */
 
 pci_dev_t pci_find_device(unsigned int vendor, unsigned int device, int index)
 {

index 2070d01..526a55c 100644
@@ -11,7 +11,7 @@
 
 #include <common.h>
 
-#if (!defined(__I386__) && !defined(CONFIG_IXDP425))
+#if !defined(__I386__)
 
 #include <asm/processor.h>
 #include <asm/io.h>

@@ -20,15 +20,6 @@
 #define cfg_read(val, addr, type, op)	*val = op((type)(addr))
 #define cfg_write(val, addr, type, op)	op((type *)(addr), (val))
 
-#ifdef CONFIG_IXP425
-extern unsigned char	in_8 (volatile unsigned *addr);
-extern unsigned short	in_le16 (volatile unsigned *addr);
-extern unsigned		in_le32 (volatile unsigned *addr);
-extern void		out_8 (volatile unsigned *addr, char val);
-extern void		out_le16 (volatile unsigned *addr, unsigned short val);
-extern void		out_le32 (volatile unsigned *addr, unsigned int val);
-#endif	/* CONFIG_IXP425 */
-
 #if defined(CONFIG_MPC8260)
 #define INDIRECT_PCI_OP(rw, size, type, op, mask)			 \
 static int								 \

@@ -134,4 +125,4 @@ void pci_setup_indirect(struct pci_controller* hose, u32 cfg_addr, u32 cfg_data)
 	hose->cfg_data = (unsigned char *) cfg_data;
 }
 
-#endif	/* !__I386__ && !CONFIG_IXDP425 */
+#endif	/* !__I386__ */

758 lines not on this page · raw message

index 1a784a1..99bc2c7 100644
@@ -262,9 +262,6 @@ init_fnc_t *init_sequence[] = {
 	init_func_i2c,
 #endif
 	dram_init,		/* configure available RAM banks */
-#if defined(CONFIG_CMD_PCI) || defined (CONFIG_PCI)
-	arm_pci_init,
-#endif
 	NULL,
 };
 

@@ -533,6 +530,9 @@ void board_init_r (gd_t *id, ulong dest_addr)
 	/* initialize environment */
 	env_relocate ();
 
+#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
+	arm_pci_init();
+#endif
 #ifdef CONFIG_VFD
 	/* must do this after the framebuffer is allocated */
 	drv_vfd_init();