ARM:OMAP4 add Phytec phyCORE-OMAP4 board

728 lines not on this page · raw message

index ac4b60d..10507a6 100644
@@ -164,6 +164,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
 		/* omap4 based boards using UART3 */
 		DEBUG_LL_OMAP4(3, omap_4430sdp);
 		DEBUG_LL_OMAP4(3, omap4_panda);
+		DEBUG_LL_OMAP4(3, pcm049);
 
 		/* zoom2/3 external uart */
 		DEBUG_LL_ZOOM(omap_zoom2);

602 lines not on this page · raw message

index 2b71b17..cb4a6c2 100644
@@ -166,6 +166,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
 		/* omap4 based boards using UART3 */
 		DEBUG_LL_OMAP4(3, omap_4430sdp);
 		DEBUG_LL_OMAP4(3, omap4_panda);
+		DEBUG_LL_OMAP4(3, pcm049);
 
 		/* zoom2/3 external uart */
 		DEBUG_LL_ZOOM(omap_zoom2);

index ad8cb46..85193ec 100644
@@ -227,18 +227,6 @@ static struct platform_device pcm049_vcc_3v3_device = {
 	},
 };
 
-static struct regulator_init_data pcm049_vusim = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 3300000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask	 =	REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-};
-
 static struct at24_platform_data board_eeprom = {
 	.byte_len = 4096,
 	.page_size = 32,

@@ -318,9 +306,7 @@ static struct i2c_board_info __initdata pcm049_i2c_4_boardinfo[] = {
 	}
 };
 
-static struct twl4030_platform_data pcm049_twldata = {
-	.vusim		= &pcm049_vusim,
-};
+static struct twl4030_platform_data pcm049_twldatai;
 
 static int __init pcm049_i2c_init(void)
 {

index ad8cb46..707929d 100644
@@ -227,18 +227,6 @@ static struct platform_device pcm049_vcc_3v3_device = {
 	},
 };
 
-static struct regulator_init_data pcm049_vusim = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 3300000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask	 =	REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-};
-
 static struct at24_platform_data board_eeprom = {
 	.byte_len = 4096,
 	.page_size = 32,

@@ -318,9 +306,7 @@ static struct i2c_board_info __initdata pcm049_i2c_4_boardinfo[] = {
 	}
 };
 
-static struct twl4030_platform_data pcm049_twldata = {
-	.vusim		= &pcm049_vusim,
-};
+static struct twl4030_platform_data pcm049_twldata;
 
 static int __init pcm049_i2c_init(void)
 {

index 0cfe200..dff174c 100644
@@ -681,20 +681,44 @@ void omap4_panda_display_init(void)
        omap_display_init(&omap4_panda_dss_data);
 }
 
+static struct omap_smsc911x_platform_data board_smsc911x_data __initdata = {
+       .cs             = OMAP4_SMSC911X_ETH_CS,
+       .gpio_irq       = OMAP4_SMSC911X_ETH_GPIO_IRQ,
+       .gpio_reset     = -EINVAL,
+       .flags          = SMSC911X_USE_16BIT,
+};
+
+static void __init omap4_panda_smsc91xx_init(void)
+{
+       if (!machine_is_pcm049())
+               return;
+
+       omap_mux_init_gpio(OMAP4_PCM049_ETH_GPIO_IRQ, OMAP_PIN_INPUT);
+       gpmc_smsc911x_init(&board_smsc911x_data);
+}
+
 static void __init omap4_panda_init(void)
 {
        int package = OMAP_PACKAGE_CBS;
 
        if (omap_rev() == OMAP4430_REV_ES1_0)
                package = OMAP_PACKAGE_CBL;
+
        omap4_mux_init(board_mux, NULL, package);
 
-       if (wl12xx_set_platform_data(&omap_panda_wlan_data))
-               pr_err("error setting wl12xx data\n");
+       if (machine_is_omap4panda()) {
+               int             ret;
+
+               ret = wl12xx_set_platform_data(&omap_panda_wlan_data);
+               if (ret)
+                       pr_err("error setting wl12xx data\n");
+
+               platform_device_register(&omap_vwlan_device);
+       }
 
+       omap4_panda_smsc91xx_init();
        omap4_panda_i2c_init();
        platform_add_devices(panda_devices, ARRAY_SIZE(panda_devices));
-       platform_device_register(&omap_vwlan_device);
        board_serial_init();
        omap4_twl6030_hsmmc_init(mmc);
 

380 lines not on this page · raw message

new file mode 100644
index 0000000..1c6a723
@@ -0,0 +1,39 @@
+#ifndef __BOAR_OAMP4PANDA_COMMON_H__
+#define __BOAR_OAMP4PANDA_COMMON_H__
+
+struct panda_board_data {
+	int hup_power_gpio;
+	int hup_nreset_gpio;
+	struct gpio_led_platform_data gpio_led_info;
+	struct omap2_hsmmc_info *mmc;
+	struct twl4030_platform_data twldata;
+	struct i2c_board_info *i2c_2_board_info;
+	int i2c_2_board_size;
+	int i2c_2_board_speed;
+	struct i2c_board_info *i2c_3_board_info;
+	int i2c_3_board_size;
+	int i2c_3_board_speed;
+	struct i2c_board_info *i2c_4_board_info;
+	int i2c_4_board_size;
+	int i2c_4_board_speed;
+	struct omap_board_data *serial1;
+	struct omap_board_data *serial2;
+	struct omap_board_data *serial3;
+	struct omap_board_data *serial4;
+
+};
+
+extern struct omap_board_data bdata;
+extern struct omap_board_data serial2_data;
+extern struct omap_board_data serial3_data;
+extern struct omap_board_data serial4_data;
+extern const struct usbhs_omap_board_data usbhs_bdata;
+extern struct omap_musb_board_data musb_board_datai;
+
+void __init omap4_panda_init_early(void);
+void omap4_common_hdmi_mux_init(void);
+
+void __init omap4_common_preinit(void);
+void __init omap4_common_init(struct panda_board_data *config);
+
+#endif /* __BOAR_OAMP4PANDA_COMMON_H__ */

476 lines not on this page · raw message

368 lines not on this page · raw message

index 2b71b17..cb4a6c2 100644
@@ -166,6 +166,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
 		/* omap4 based boards using UART3 */
 		DEBUG_LL_OMAP4(3, omap_4430sdp);
 		DEBUG_LL_OMAP4(3, omap4_panda);
+		DEBUG_LL_OMAP4(3, pcm049);
 
 		/* zoom2/3 external uart */
 		DEBUG_LL_ZOOM(omap_zoom2);

index 9aaa960..b9bea86 100644
@@ -47,23 +47,11 @@
 #include "mux.h"
 #include "common-board-devices.h"
 
-#define GPIO_HUB_POWER		1
-#define GPIO_HUB_NRESET		62
 #define GPIO_WIFI_PMENA		43
 #define GPIO_WIFI_IRQ		53
 #define HDMI_GPIO_HPD 60 /* Hot plug pin for HDMI */
 #define HDMI_GPIO_LS_OE 41 /* Level shifter for HDMI */
 
-/* wl127x BT, FM, GPS connectivity chip */
-static int wl1271_gpios[] = {46, -1, -1};
-static struct platform_device wl1271_device = {
-	.name	= "kim",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &wl1271_gpios,
-	},
-};
-
 static struct gpio_led gpio_leds[] = {
 	{
 		.name			= "pandaboard::status1",

@@ -77,21 +65,219 @@ static struct gpio_led gpio_leds[] = {
 	},
 };
 
-static struct gpio_led_platform_data gpio_led_info = {
-	.leds		= gpio_leds,
-	.num_leds	= ARRAY_SIZE(gpio_leds),
+/*
+ * Display monitor features are burnt in their EEPROM as EDID data. The EEPROM
+ * is connected as I2C slave device, and can be accessed at address 0x50
+ */
+static struct i2c_board_info __initdata panda_i2c_eeprom[] = {
+	{
+		I2C_BOARD_INFO("eeprom", 0x50),
+	},
+};
+
+#ifdef CONFIG_OMAP_MUX
+static struct omap_board_mux board_mux[] __initdata = {
+	/* dispc2_data23 */
+	OMAP4_MUX(USBB2_ULPITLL_STP, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data22 */
+	OMAP4_MUX(USBB2_ULPITLL_DIR, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data21 */
+	OMAP4_MUX(USBB2_ULPITLL_NXT, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data20 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT0, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data19 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT1, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data18 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT2, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data15 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT3, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data14 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT4, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data13 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT5, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data12 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT6, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data11 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT7, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data10 */
+	OMAP4_MUX(DPM_EMU3, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data9 */
+	OMAP4_MUX(DPM_EMU4, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data16 */
+	OMAP4_MUX(DPM_EMU5, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data17 */
+	OMAP4_MUX(DPM_EMU6, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_hsync */
+	OMAP4_MUX(DPM_EMU7, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_pclk */
+	OMAP4_MUX(DPM_EMU8, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_vsync */
+	OMAP4_MUX(DPM_EMU9, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_de */
+	OMAP4_MUX(DPM_EMU10, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data8 */
+	OMAP4_MUX(DPM_EMU11, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data7 */
+	OMAP4_MUX(DPM_EMU12, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data6 */
+	OMAP4_MUX(DPM_EMU13, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data5 */
+	OMAP4_MUX(DPM_EMU14, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data4 */
+	OMAP4_MUX(DPM_EMU15, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data3 */
+	OMAP4_MUX(DPM_EMU16, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data2 */
+	OMAP4_MUX(DPM_EMU17, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data1 */
+	OMAP4_MUX(DPM_EMU18, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data0 */
+	OMAP4_MUX(DPM_EMU19, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	{ .reg_offset = OMAP_MUX_TERMINATOR },
+};
+
+static struct omap_device_pad serial2_pads[] __initdata = {
+	OMAP_MUX_STATIC("uart2_cts.uart2_cts",
+			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
+	OMAP_MUX_STATIC("uart2_rts.uart2_rts",
+			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
+	OMAP_MUX_STATIC("uart2_rx.uart2_rx",
+			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
+	OMAP_MUX_STATIC("uart2_tx.uart2_tx",
+			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
+};
+
+static struct omap_device_pad serial3_pads[] __initdata = {
+	OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
+			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
+	OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
+			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
+	OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
+			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
+	OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
+			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
+};
+
+static struct omap_device_pad serial4_pads[] __initdata = {
+	OMAP_MUX_STATIC("uart4_rx.uart4_rx",
+			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
+	OMAP_MUX_STATIC("uart4_tx.uart4_tx",
+			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
+};
+
+static struct omap_board_data serial2_data __initdata = {
+	.id             = 1,
+	.pads           = serial2_pads,
+	.pads_cnt       = ARRAY_SIZE(serial2_pads),
+};
+
+static struct omap_board_data serial3_data __initdata = {
+	.id             = 2,
+	.pads           = serial3_pads,
+	.pads_cnt       = ARRAY_SIZE(serial3_pads),
+};
+
+static struct omap_board_data serial4_data __initdata = {
+	.id             = 3,
+	.pads           = serial4_pads,
+	.pads_cnt       = ARRAY_SIZE(serial4_pads),
+};
+#else
+#define board_mux	NULL
+#endif
+
+/* dummy data for UART1 */
+struct omap_board_data bdata;
+
+static struct omap2_hsmmc_info omap4_panda_mmc[] = {
+	{
+		.mmc		= 1,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
+		.gpio_wp	= -EINVAL,
+		.gpio_cd	= -EINVAL,
+	},
+	{
+		.name		= "wl1271",
+		.mmc		= 5,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD,
+		.gpio_wp	= -EINVAL,
+		.gpio_cd	= -EINVAL,
+		.ocr_mask	= MMC_VDD_165_195,
+		.nonremovable	= true,
+	},
+	{}	/* Terminator */
+};
+
+/*
+ * Board-specific configuration
+ */
+static struct {
+	int hup_power_gpio;
+	int hup_nreset_gpio;
+	struct gpio_led_platform_data gpio_led_info;
+	struct omap2_hsmmc_info *mmc;
+	struct twl4030_platform_data twldata;
+	struct i2c_board_info *i2c_2_board_info;
+	int i2c_2_board_size;
+	int i2c_2_board_speed;
+	struct i2c_board_info *i2c_3_board_info;
+	int i2c_3_board_size;
+	int i2c_3_board_speed;
+	struct i2c_board_info *i2c_4_board_info;
+	int i2c_4_board_size;
+	int i2c_4_board_speed;
+	struct omap_board_data *serial1;
+	struct omap_board_data *serial2;
+	struct omap_board_data *serial3;
+	struct omap_board_data *serial4;
+} omap4_panda_config = {
+	.hup_power_gpio = 1,
+	.hup_nreset_gpio = 62,
+	.gpio_led_info.leds = gpio_leds,
+	.gpio_led_info.num_leds	= ARRAY_SIZE(gpio_leds),
+	.mmc = omap4_panda_mmc,
+	.i2c_2_board_info = NULL,
+	.i2c_2_board_size = 0,
+	.i2c_2_board_speed = 400,
+	.i2c_3_board_info = panda_i2c_eeprom,
+	.i2c_3_board_size = ARRAY_SIZE(panda_i2c_eeprom),
+	/*
+	 * Bus 3 is attached to the DVI port where devices like the pico DLP
+	 * projector don't work reliably with 400kHz
+	 */
+	.i2c_3_board_speed = 100,
+	.i2c_4_board_info = NULL,
+	.i2c_4_board_size = 0,
+	.i2c_4_board_speed = 400,
+	.serial1 = &bdata,
+	.serial2 = &serial2_data,
+	.serial3 = &serial3_data,
+	.serial4 = &serial4_data,
+};
+
+/* wl127x BT, FM, GPS connectivity chip */
+static int wl1271_gpios[] = {46, -1, -1};
+static struct platform_device wl1271_device = {
+	.name	= "kim",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &wl1271_gpios,
+	},
 };
 
 static struct platform_device leds_gpio = {
 	.name	= "leds-gpio",
 	.id	= -1,
 	.dev	= {
-		.platform_data	= &gpio_led_info,
+		.platform_data	= &omap4_panda_config.gpio_led_info,
 	},
 };
 
-static struct platform_device *panda_devices[] __initdata = {
+static struct platform_device *common_devices[] __initdata = {
 	&leds_gpio,
+};
+
+static struct platform_device *panda_devices[] __initdata = {
 	&wl1271_device,
 };
 

@@ -111,11 +297,6 @@ static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
 	.reset_gpio_port[2]  = -EINVAL
 };
 
-static struct gpio panda_ehci_gpios[] __initdata = {
-	{ GPIO_HUB_POWER,	GPIOF_OUT_INIT_LOW,  "hub_power"  },
-	{ GPIO_HUB_NRESET,	GPIOF_OUT_INIT_LOW,  "hub_nreset" },
-};
-
 static void __init omap4_ehci_init(void)
 {
 	int ret;

@@ -131,21 +312,32 @@ static void __init omap4_ehci_init(void)
 	clk_enable(phy_ref_clk);
 
 	/* disable the power to the usb hub prior to init and reset phy+hub */
-	ret = gpio_request_array(panda_ehci_gpios,
-				 ARRAY_SIZE(panda_ehci_gpios));
-	if (ret) {
-		pr_err("Unable to initialize EHCI power/reset\n");
-		return;
+	if (omap4_panda_config.hup_power_gpio != -EINVAL) {
+		ret = gpio_request_one(omap4_panda_config.hup_power_gpio, 
+				GPIOF_OUT_INIT_LOW,  "hub_power");
+		if (ret) {
+			pr_err("Unable to initialize EHCI power\n");
+			return;
+		}
+		gpio_export(omap4_panda_config.hup_power_gpio, 0);
 	}
 
-	gpio_export(GPIO_HUB_POWER, 0);
-	gpio_export(GPIO_HUB_NRESET, 0);
-	gpio_set_value(GPIO_HUB_NRESET, 1);
+	if (omap4_panda_config.hup_nreset_gpio != -EINVAL) {
+		ret = gpio_request_one(omap4_panda_config.hup_nreset_gpio,
+				GPIOF_OUT_INIT_LOW,  "hub_nreset");
+		if (ret) {
+			pr_err("Unable to initialize EHCI reset\n");
+			return;
+		}
+		gpio_export(omap4_panda_config.hup_nreset_gpio, 0);
+		gpio_set_value(omap4_panda_config.hup_nreset_gpio, 1);
+	}
 
 	usbhs_init(&usbhs_bdata);
 
 	/* enable power to hub */
-	gpio_set_value(GPIO_HUB_POWER, 1);
+	if (omap4_panda_config.hup_power_gpio != -EINVAL)
+		gpio_set_value(omap4_panda_config.hup_power_gpio, 1);
 }
 
 static struct omap_musb_board_data musb_board_data = {

@@ -154,25 +346,6 @@ static struct omap_musb_board_data musb_board_data = {
 	.power			= 100,
 };
 
-static struct omap2_hsmmc_info mmc[] = {
-	{
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
-		.gpio_wp	= -EINVAL,
-		.gpio_cd	= -EINVAL,
-	},
-	{
-		.name		= "wl1271",
-		.mmc		= 5,
-		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD,
-		.gpio_wp	= -EINVAL,
-		.gpio_cd	= -EINVAL,
-		.ocr_mask	= MMC_VDD_165_195,
-		.nonremovable	= true,
-	},
-	{}	/* Terminator */
-};
-
 static struct regulator_consumer_supply omap4_panda_vmmc5_supply[] = {
 	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.4"),
 };

@@ -257,22 +430,10 @@ static int __init omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers)
 	return 0;
 }
 
-/* Panda board uses the common PMIC configuration */
-static struct twl4030_platform_data omap4_panda_twldata;
-
-/*
- * Display monitor features are burnt in their EEPROM as EDID data. The EEPROM
- * is connected as I2C slave device, and can be accessed at address 0x50
- */
-static struct i2c_board_info __initdata panda_i2c_eeprom[] = {
-	{
-		I2C_BOARD_INFO("eeprom", 0x50),
-	},
-};
-
 static int __init omap4_panda_i2c_init(void)
 {
-	omap4_pmic_get_config(&omap4_panda_twldata, TWL_COMMON_PDATA_USB,
+	omap4_pmic_get_config(&omap4_panda_config.twldata, 
+			TWL_COMMON_PDATA_USB,
 			TWL_COMMON_REGULATOR_VDAC |
 			TWL_COMMON_REGULATOR_VAUX2 |
 			TWL_COMMON_REGULATOR_VAUX3 |

@@ -282,157 +443,40 @@ static int __init omap4_panda_i2c_init(void)
 			TWL_COMMON_REGULATOR_VCXIO |
 			TWL_COMMON_REGULATOR_VUSB |
 			TWL_COMMON_REGULATOR_CLK32KG);
-	omap4_pmic_init("twl6030", &omap4_panda_twldata);
-	omap_register_i2c_bus(2, 400, NULL, 0);
-	/*
-	 * Bus 3 is attached to the DVI port where devices like the pico DLP
-	 * projector don't work reliably with 400kHz
-	 */
-	omap_register_i2c_bus(3, 100, panda_i2c_eeprom,
-					ARRAY_SIZE(panda_i2c_eeprom));
-	omap_register_i2c_bus(4, 400, NULL, 0);
+	omap4_pmic_init("twl6030", &omap4_panda_config.twldata);
+	if (!omap4_panda_config.i2c_2_board_speed)
+		omap_register_i2c_bus(2, omap4_panda_config.i2c_2_board_speed,
+				omap4_panda_config.i2c_2_board_info, 
+				omap4_panda_config.i2c_2_board_size);
+	if (!omap4_panda_config.i2c_3_board_speed)
+		omap_register_i2c_bus(3, omap4_panda_config.i2c_3_board_speed,
+				omap4_panda_config.i2c_3_board_info,
+				omap4_panda_config.i2c_3_board_size);
+	if (!omap4_panda_config.i2c_4_board_speed)
+		omap_register_i2c_bus(4, omap4_panda_config.i2c_4_board_speed, 
+				omap4_panda_config.i2c_4_board_info,
+				omap4_panda_config.i2c_4_board_size);
 	return 0;
 }
 
 #ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	/* WLAN IRQ - GPIO 53 */
-	OMAP4_MUX(GPMC_NCS3, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	/* WLAN POWER ENABLE - GPIO 43 */
-	OMAP4_MUX(GPMC_A19, OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT),
-	/* WLAN SDIO: MMC5 CMD */
-	OMAP4_MUX(SDMMC5_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	/* WLAN SDIO: MMC5 CLK */
-	OMAP4_MUX(SDMMC5_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	/* WLAN SDIO: MMC5 DAT[0-3] */
-	OMAP4_MUX(SDMMC5_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	OMAP4_MUX(SDMMC5_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	OMAP4_MUX(SDMMC5_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	OMAP4_MUX(SDMMC5_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	/* gpio 0 - TFP410 PD */
-	OMAP4_MUX(KPD_COL1, OMAP_PIN_OUTPUT | OMAP_MUX_MODE3),
-	/* dispc2_data23 */
-	OMAP4_MUX(USBB2_ULPITLL_STP, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data22 */
-	OMAP4_MUX(USBB2_ULPITLL_DIR, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data21 */
-	OMAP4_MUX(USBB2_ULPITLL_NXT, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data20 */
-	OMAP4_MUX(USBB2_ULPITLL_DAT0, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data19 */
-	OMAP4_MUX(USBB2_ULPITLL_DAT1, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data18 */
-	OMAP4_MUX(USBB2_ULPITLL_DAT2, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data15 */
-	OMAP4_MUX(USBB2_ULPITLL_DAT3, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data14 */
-	OMAP4_MUX(USBB2_ULPITLL_DAT4, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data13 */
-	OMAP4_MUX(USBB2_ULPITLL_DAT5, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data12 */
-	OMAP4_MUX(USBB2_ULPITLL_DAT6, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data11 */
-	OMAP4_MUX(USBB2_ULPITLL_DAT7, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data10 */
-	OMAP4_MUX(DPM_EMU3, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data9 */
-	OMAP4_MUX(DPM_EMU4, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data16 */
-	OMAP4_MUX(DPM_EMU5, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data17 */
-	OMAP4_MUX(DPM_EMU6, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_hsync */
-	OMAP4_MUX(DPM_EMU7, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_pclk */
-	OMAP4_MUX(DPM_EMU8, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_vsync */
-	OMAP4_MUX(DPM_EMU9, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_de */
-	OMAP4_MUX(DPM_EMU10, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data8 */
-	OMAP4_MUX(DPM_EMU11, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data7 */
-	OMAP4_MUX(DPM_EMU12, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data6 */
-	OMAP4_MUX(DPM_EMU13, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data5 */
-	OMAP4_MUX(DPM_EMU14, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data4 */
-	OMAP4_MUX(DPM_EMU15, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data3 */
-	OMAP4_MUX(DPM_EMU16, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data2 */
-	OMAP4_MUX(DPM_EMU17, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data1 */
-	OMAP4_MUX(DPM_EMU18, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	/* dispc2_data0 */
-	OMAP4_MUX(DPM_EMU19, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-
-static struct omap_device_pad serial2_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart2_cts.uart2_cts",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rts.uart2_rts",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rx.uart2_rx",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_tx.uart2_tx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial3_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
-			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial4_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart4_rx.uart4_rx",
-			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart4_tx.uart4_tx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_board_data serial2_data __initdata = {
-	.id             = 1,
-	.pads           = serial2_pads,
-	.pads_cnt       = ARRAY_SIZE(serial2_pads),
-};
-
-static struct omap_board_data serial3_data __initdata = {
-	.id             = 2,
-	.pads           = serial3_pads,
-	.pads_cnt       = ARRAY_SIZE(serial3_pads),
-};
-
-static struct omap_board_data serial4_data __initdata = {
-	.id             = 3,
-	.pads           = serial4_pads,
-	.pads_cnt       = ARRAY_SIZE(serial4_pads),
-};
-
 static inline void board_serial_init(void)
 {
-	struct omap_board_data bdata;
+	/* pass dummy data for UART1 */
 	bdata.flags     = 0;
 	bdata.pads      = NULL;
 	bdata.pads_cnt  = 0;
 	bdata.id        = 0;
-	/* pass dummy data for UART1 */
-	omap_serial_init_port(&bdata);
-
-	omap_serial_init_port(&serial2_data);
-	omap_serial_init_port(&serial3_data);
-	omap_serial_init_port(&serial4_data);
+	if (omap4_panda_config.serial1)
+		omap_serial_init_port(omap4_panda_config.serial1);
+	if (omap4_panda_config.serial2)
+		omap_serial_init_port(omap4_panda_config.serial2);
+	if (omap4_panda_config.serial3)
+		omap_serial_init_port(omap4_panda_config.serial3);
+	if (omap4_panda_config.serial4)
+		omap_serial_init_port(omap4_panda_config.serial4);
 }
 #else
-#define board_mux	NULL
 
 static inline void board_serial_init(void)
 {

@@ -554,7 +598,9 @@ void omap4_panda_display_init(void)
 	omap_display_init(&omap4_panda_dss_data);
 }
 
-static void __init omap4_panda_init(void)
+static struct omap_mux_partition *partition;
+
+static void __init omap4_common_preinit(void)
 {
 	int package = OMAP_PACKAGE_CBS;
 

@@ -562,16 +608,50 @@ static void __init omap4_panda_init(void)
 		package = OMAP_PACKAGE_CBL;
 	omap4_mux_init(board_mux, NULL, package);
 
-	if (wl12xx_set_platform_data(&omap_panda_wlan_data))
-		pr_err("error setting wl12xx data\n");
+	partition = omap_mux_get("core");
+}
 
+static void __init omap4_common_init(void)
+{
+	platform_add_devices(common_devices, ARRAY_SIZE(common_devices));
+	omap4_twl6030_hsmmc_init(omap4_panda_config.mmc);
 	omap4_panda_i2c_init();
-	platform_add_devices(panda_devices, ARRAY_SIZE(panda_devices));
-	platform_device_register(&omap_vwlan_device);
 	board_serial_init();
-	omap4_twl6030_hsmmc_init(mmc);
 	omap4_ehci_init();
 	usb_musb_init(&musb_board_data);
+}
+
+static struct omap_board_mux omap4_panda_mux[] = {
+#ifdef CONFIG_OMAP_MUX
+	/* WLAN IRQ - GPIO 53 */
+	OMAP4_MUX(GPMC_NCS3, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
+	/* WLAN POWER ENABLE - GPIO 43 */
+	OMAP4_MUX(GPMC_A19, OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT),
+	/* WLAN SDIO: MMC5 CMD */
+	OMAP4_MUX(SDMMC5_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	/* WLAN SDIO: MMC5 CLK */
+	OMAP4_MUX(SDMMC5_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	/* WLAN SDIO: MMC5 DAT[0-3] */
+	OMAP4_MUX(SDMMC5_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP4_MUX(SDMMC5_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP4_MUX(SDMMC5_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP4_MUX(SDMMC5_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	/* gpio 0 - TFP410 PD */
+	OMAP4_MUX(KPD_COL1, OMAP_PIN_OUTPUT | OMAP_MUX_MODE3),
+#endif
+	{ .reg_offset = OMAP_MUX_TERMINATOR },
+};
+
+static void __init omap4_panda_init(void)
+{
+	omap4_common_preinit();
+	omap_mux_write_array(partition, omap4_panda_mux);
+	omap4_common_init();
+	if (wl12xx_set_platform_data(&omap_panda_wlan_data))
+		pr_err("error setting wl12xx data\n");
+
+	platform_add_devices(panda_devices, ARRAY_SIZE(panda_devices));
+	platform_device_register(&omap_vwlan_device);
 	omap4_panda_display_init();
 }
 

345 lines not on this page · raw message

index 2b71b17..cb4a6c2 100644
@@ -166,6 +166,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
 		/* omap4 based boards using UART3 */
 		DEBUG_LL_OMAP4(3, omap_4430sdp);
 		DEBUG_LL_OMAP4(3, omap4_panda);
+		DEBUG_LL_OMAP4(3, pcm049);
 
 		/* zoom2/3 external uart */
 		DEBUG_LL_ZOOM(omap_zoom2);

index ac4b60d..10507a6 100644
@@ -164,6 +164,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
 		/* omap4 based boards using UART3 */
 		DEBUG_LL_OMAP4(3, omap_4430sdp);
 		DEBUG_LL_OMAP4(3, omap4_panda);
+		DEBUG_LL_OMAP4(3, pcm049);
 
 		/* zoom2/3 external uart */
 		DEBUG_LL_ZOOM(omap_zoom2);

new file mode 100644
index 0000000..51bb7a7
@@ -0,0 +1,728 @@
+/*
+ * Board support file for Phytec phyCORE-OMAP4 Board.
+ *
+ * Copyright (C) 2011 Phytec Messtechnik GmbH
+ *
+ * Author: Jan Weitzel <[email protected]>
+ *
+ * Based on mach-omap2/board-omap4panda.c
+ *
+ * Author: David Anders <[email protected]>
+ *
+ * Author: Santosh Shilimkar <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/gpio.h>
+#include <linux/usb/otg.h>
+#include <linux/i2c/twl.h>
+#include <linux/i2c/at24.h>
+#include <linux/mfd/stmpe.h>
+#include <linux/leds-pca9532.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
+#include <linux/smsc911x.h>
+
+#include <mach/hardware.h>
+#include <mach/omap4-common.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <video/omapdss.h>
+
+#include <plat/board.h>
+#include <plat/common.h>
+#include <plat/usb.h>
+#include <plat/gpmc.h>
+#include <plat/gpmc-smsc911x.h>
+#include <plat/mmc.h>
+#include <video/omap-panel-generic-dpi.h>
+#include "timer-gp.h"
+
+#include "hsmmc.h"
+#include "control.h"
+#include "mux.h"
+#include "common-board-devices.h"
+
+#define OMAP4_PCM049_ETH_GPIO_IRQ	121
+#define OMAP4_PCM049_ETH_CS		5
+#define OMAP4_PCM049_STMPE811_GPIO_IRQ	117
+#define OMAP4_PCM049_LCD_ENABLE		118
+
+static struct gpio_led gpio_leds[] = {
+	{
+		.name			= "modul:red:status1",
+		.default_trigger	= "heartbeat",
+		.gpio			= 152,
+	},
+	{
+		.name			= "modul:green:status2",
+		.default_trigger	= "mmc0",
+		.gpio			= 153,
+	},
+};
+
+static struct gpio_led_platform_data gpio_led_info = {
+	.leds		= gpio_leds,
+	.num_leds	= ARRAY_SIZE(gpio_leds),
+};
+
+static struct platform_device leds_gpio = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &gpio_led_info,
+	},
+};
+
+static void __init pcm049_init_early(void)
+{
+	omap2_init_common_infrastructure();
+	omap2_init_common_devices(NULL, NULL);
+}
+
+static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
+	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+	.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
+	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+	.phy_reset  = false,
+	.reset_gpio_port[0]  = -EINVAL,
+	.reset_gpio_port[1]  = -EINVAL,
+	.reset_gpio_port[2]  = -EINVAL
+};
+
+static void __init omap4_ehci_init(void)
+{
+	struct clk *phy_ref_clk;
+	/* FREF_CLK3 provides the 19.2 MHz reference clock to the PHY */
+	phy_ref_clk = clk_get(NULL, "auxclk3_ck");
+	if (IS_ERR(phy_ref_clk)) {
+		pr_err("Cannot request auxclk3\n");
+		return;
+	}
+	clk_set_rate(phy_ref_clk, 19200000);
+	clk_enable(phy_ref_clk);
+
+	usbhs_init(&usbhs_bdata);
+	return;
+}
+
+static struct omap_musb_board_data musb_board_data = {
+	.interface_type		= MUSB_INTERFACE_UTMI,
+	.mode			= MUSB_OTG,
+	.power			= 100,
+};
+
+static struct twl4030_usb_data omap4_usbphy_data = {
+	.phy_init	= omap4430_phy_init,
+	.phy_exit	= omap4430_phy_exit,
+	.phy_power	= omap4430_phy_power,
+	.phy_set_clock	= omap4430_phy_set_clk,
+	.phy_suspend	= omap4430_phy_suspend,
+};
+
+static struct omap2_hsmmc_info mmc[] = {
+	{
+		.mmc		= 1,
+		.caps		= MMC_CAP_4_BIT_DATA,
+		.gpio_wp	= -EINVAL,
+		.gpio_cd	= -EINVAL,
+	}, {
+		.mmc		= 5,
+		.caps		= MMC_CAP_4_BIT_DATA,
+		.gpio_wp	= -EINVAL,
+		.gpio_cd	= 30,	/* wk30 */
+		.ocr_mask	= MMC_VDD_32_33 | MMC_VDD_33_34, /* 3V3 */
+	}, {}	/* Terminator */
+};
+
+static struct regulator_consumer_supply pcm049_vmmc_supply[] = {
+	{
+		.supply = "vmmc",
+		.dev_name = "omap_hsmmc.0",
+	},
+};
+
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+static struct omap_smsc911x_platform_data __initdata board_smsc911x_data = {
+	.cs             = OMAP4_PCM049_ETH_CS,
+	.gpio_irq       = OMAP4_PCM049_ETH_GPIO_IRQ,
+	.gpio_reset     = -EINVAL,
+	.flags          = SMSC911X_USE_16BIT,
+};
+
+static inline void __init pcm049_init_smsc911x(void)
+{
+	omap_mux_init_gpio(OMAP4_PCM049_ETH_GPIO_IRQ, OMAP_PIN_INPUT);
+	gpmc_smsc911x_init(&board_smsc911x_data);
+}
+#else
+static inline void __init pcm049_init_smsc911x(void) { return; }
+#endif
+
+static int omap4_twl6030_hsmmc_late_init(struct device *dev)
+{
+	int ret = 0;
+	struct platform_device *pdev = container_of(dev,
+				struct platform_device, dev);
+	struct omap_mmc_platform_data *pdata = dev->platform_data;
+
+	/* Setting MMC1 Card detect Irq */
+	if (pdev->id == 0) {
+		ret = twl6030_mmc_card_detect_config();
+		if (ret)
+			dev_err(dev, "%s: Error card detect config(%d)\n",
+				__func__, ret);
+		pdata->slots[0].card_detect_irq = TWL6030_IRQ_BASE +
+						MMCDETECT_INTR_OFFSET;
+		pdata->slots[0].card_detect = twl6030_mmc_card_detect;
+	}
+	return ret;
+}
+
+static __init void omap4_twl6030_hsmmc_set_late_init(struct device *dev)
+{
+	struct omap_mmc_platform_data *pdata;
+
+	/* dev can be null if CONFIG_MMC_OMAP_HS is not set */
+	if (!dev) {
+		pr_err("Failed omap4_twl6030_hsmmc_set_late_init\n");
+		return;
+	}
+	pdata = dev->platform_data;
+
+	pdata->init =	omap4_twl6030_hsmmc_late_init;
+}
+
+static int __init omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers)
+{
+	struct omap2_hsmmc_info *c;
+
+	omap2_hsmmc_init(controllers);
+	for (c = controllers; c->mmc; c++)
+		omap4_twl6030_hsmmc_set_late_init(c->dev);
+
+	return 0;
+}
+
+/* Fixed regulator for max1027 */
+static struct regulator_consumer_supply pcm049_vcc_3v3_consumer_supply[] = {
+	REGULATOR_SUPPLY("vcc", "4-0064"),
+};
+
+struct regulator_init_data pcm049_vcc_3v3_initdata = {
+	.consumer_supplies = pcm049_vcc_3v3_consumer_supply,
+	.num_consumer_supplies = ARRAY_SIZE(pcm049_vcc_3v3_consumer_supply),
+	.constraints = {
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static struct fixed_voltage_config pcm049_vcc_3v3_config = {
+	.supply_name		= "pcm049_vcc_3v3",
+	.microvolts		= 3300000,
+	.gpio			= -EINVAL,
+	.enabled_at_boot	= 1,
+	.init_data		= &pcm049_vcc_3v3_initdata,
+};
+
+static struct platform_device pcm049_vcc_3v3_device = {
+	.name	= "reg-fixed-voltage",
+	.id	= 0,
+	.dev	= {
+		.platform_data = &pcm049_vcc_3v3_config,
+	},
+};
+
+static struct regulator_init_data pcm049_vaux2 = {
+	.constraints = {
+		.min_uV			= 1200000,
+		.max_uV			= 2800000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask	 = REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static struct regulator_init_data pcm049_vaux3 = {
+	.constraints = {
+		.min_uV			= 1000000,
+		.max_uV			= 3000000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask	 = REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+/* VMMC1 for MMC1 card */
+static struct regulator_init_data pcm049_vmmc = {
+	.constraints = {
+		.min_uV			= 1200000,
+		.max_uV			= 3000000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask	 = REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies  = 1,
+	.consumer_supplies      = pcm049_vmmc_supply,
+};
+
+static struct regulator_init_data pcm049_vpp = {
+	.constraints = {
+		.min_uV			= 1800000,
+		.max_uV			= 2500000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask	 = REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static struct regulator_init_data pcm049_vana = {
+	.constraints = {
+		.min_uV			= 2100000,
+		.max_uV			= 2100000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask	 = REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static struct regulator_init_data pcm049_vcxio = {
+	.constraints = {
+		.min_uV			= 1800000,
+		.max_uV			= 1800000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask	 = REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static struct regulator_init_data pcm049_vdac = {
+	.constraints = {
+		.min_uV			= 1800000,
+		.max_uV			= 1800000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask	 = REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static struct regulator_init_data pcm049_vusb = {
+	.constraints = {
+		.min_uV			= 3300000,
+		.max_uV			= 3300000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask	 =	REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static struct regulator_init_data pcm049_vusim = {
+	.constraints = {
+		.min_uV			= 1800000,
+		.max_uV			= 3300000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask	 =	REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static struct regulator_init_data pcm049_clk32kg = {
+	.constraints = {
+		.valid_ops_mask		= REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static struct twl4030_platform_data pcm049_twldata = {
+	.irq_base	= TWL6030_IRQ_BASE,
+	.irq_end	= TWL6030_IRQ_END,
+
+	/* Regulators */
+	.vmmc		= &pcm049_vmmc,
+	.vpp		= &pcm049_vpp,
+	.vana		= &pcm049_vana,
+	.vcxio		= &pcm049_vcxio,
+	.vdac		= &pcm049_vdac,
+	.vusb		= &pcm049_vusb,
+	.vaux2		= &pcm049_vaux2,
+	.vaux3		= &pcm049_vaux3,
+	.clk32kg	= &pcm049_clk32kg,
+	.usb		= &omap4_usbphy_data,
+	.vusim		= &pcm049_vusim,
+};
+
+static struct at24_platform_data board_eeprom = {
+	.byte_len = 4096,
+	.page_size = 32,
+	.flags = AT24_FLAG_ADDR16,
+};
+
+static struct stmpe_gpio_platform_data pba_gpio_stm_data = {
+	.gpio_base = -1,
+	.norequest_mask = STMPE_GPIO_NOREQ_811_TOUCH,
+};
+
+static struct stmpe_ts_platform_data pba_ts_stm_pdata = {
+	.sample_time = 4,
+	.mod_12b = 1,
+	.ref_sel = 0,
+	.adc_freq = 1,
+	.ave_ctrl = 3,
+	.touch_det_delay = 3,
+	.settling = 3,
+	.fraction_z = 7,
+	.i_drive = 0,
+};
+
+static struct stmpe_platform_data pba_stm_pdata = {
+	.blocks = STMPE_BLOCK_GPIO | STMPE_BLOCK_TOUCHSCREEN,
+	.irq_base = TWL6030_IRQ_END,
+	.irq_trigger = IRQF_TRIGGER_RISING,
+	.irq_invert_polarity = true,
+	.gpio = &pba_gpio_stm_data,
+	.ts = &pba_ts_stm_pdata,
+};
+
+static struct pca9532_platform_data pba_pca9532 = {
+	.leds = {
+		{
+			.name = "board:red:free_use1",
+			.state = PCA9532_OFF,
+			.type = PCA9532_TYPE_LED,
+		}, {
+			.name = "board:yellow:free_use2",
+			.state = PCA9532_OFF,
+			.type = PCA9532_TYPE_LED,
+		}, {
+			.name = "board:yellow:free_use3",
+			.state = PCA9532_OFF,
+			.type = PCA9532_TYPE_LED,
+		}, {
+			.name = "board:green:free_use4",
+			.state = PCA9532_OFF,
+			.type = PCA9532_TYPE_LED,
+		},
+	},
+	.psc = { 1, 1 },
+	.pwm = { 1, 1 },
+};
+
+static struct i2c_board_info __initdata pcm049_i2c_1_boardinfo[] = {
+	{
+		I2C_BOARD_INFO("at24", 0x57), /* E0=1, E1=1, E2=1 */
+		.platform_data = &board_eeprom,
+	},
+};
+
+static struct i2c_board_info __initdata pcm049_i2c_3_boardinfo[] = {
+};
+
+static struct i2c_board_info __initdata pcm049_i2c_4_boardinfo[] = {
+	{
+		I2C_BOARD_INFO("stmpe811", 0x41),	/* Touch controller */
+		.irq = OMAP_GPIO_IRQ(OMAP4_PCM049_STMPE811_GPIO_IRQ),
+		.platform_data = &pba_stm_pdata,
+	}, {
+		I2C_BOARD_INFO("max1037", 0x64),	/* A/D converter */
+	}, {
+		I2C_BOARD_INFO("pca9533", 0x62),	/* Leds pca9533 */
+		.platform_data = &pba_pca9532,
+	}
+};
+
+static int __init pcm049_i2c_init(void)
+{
+	/* I2C1 */
+	omap4_pmic_init("twl6030", &pcm049_twldata);
+	i2c_register_board_info(1, pcm049_i2c_1_boardinfo,
+				ARRAY_SIZE(pcm049_i2c_1_boardinfo));
+
+	/* I2C3 */
+	omap_register_i2c_bus(3, 400, pcm049_i2c_3_boardinfo,
+				ARRAY_SIZE(pcm049_i2c_3_boardinfo));
+
+	/* I2C4 */
+	if (omap_mux_init_gpio(OMAP4_PCM049_STMPE811_GPIO_IRQ, OMAP_PIN_INPUT))
+		printk(KERN_ERR "Failed to mux GPIO%d for STMPE811 IRQ\n",
+			OMAP4_PCM049_STMPE811_GPIO_IRQ);
+	else if (gpio_request(OMAP4_PCM049_STMPE811_GPIO_IRQ, "STMPE811 irq"))
+		printk(KERN_ERR "Failed to request GPIO%d for STMPE811 IRQ\n",
+			OMAP4_PCM049_STMPE811_GPIO_IRQ);
+	else
+		gpio_direction_input(OMAP4_PCM049_STMPE811_GPIO_IRQ);
+
+	omap_register_i2c_bus(4, 400, pcm049_i2c_4_boardinfo,
+				ARRAY_SIZE(pcm049_i2c_4_boardinfo));
+	return 0;
+}
+
+#ifdef CONFIG_OMAP_MUX
+static struct omap_board_mux board_mux[] __initdata = {
+	OMAP4_MUX(SDMMC5_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP4_MUX(SDMMC5_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP4_MUX(SDMMC5_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP4_MUX(SDMMC5_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+
+	/* dispc2_data23 */
+	OMAP4_MUX(USBB2_ULPITLL_STP, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data22 */
+	OMAP4_MUX(USBB2_ULPITLL_DIR, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data21 */
+	OMAP4_MUX(USBB2_ULPITLL_NXT, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data20 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT0, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data19 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT1, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data18 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT2, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data15 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT3, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data14 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT4, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data13 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT5, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data12 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT6, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data11 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT7, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data10 */
+	OMAP4_MUX(DPM_EMU3, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data9 */
+	OMAP4_MUX(DPM_EMU4, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data16 */
+	OMAP4_MUX(DPM_EMU5, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data17 */
+	OMAP4_MUX(DPM_EMU6, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_hsync */
+	OMAP4_MUX(DPM_EMU7, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_pclk */
+	OMAP4_MUX(DPM_EMU8, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_vsync */
+	OMAP4_MUX(DPM_EMU9, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_de */
+	OMAP4_MUX(DPM_EMU10, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data8 */
+	OMAP4_MUX(DPM_EMU11, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data7 */
+	OMAP4_MUX(DPM_EMU12, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data6 */
+	OMAP4_MUX(DPM_EMU13, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data5 */
+	OMAP4_MUX(DPM_EMU14, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data4 */
+	OMAP4_MUX(DPM_EMU15, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data3 */
+	OMAP4_MUX(DPM_EMU16, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data2 */
+	OMAP4_MUX(DPM_EMU17, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data1 */
+	OMAP4_MUX(DPM_EMU18, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data0 */
+	OMAP4_MUX(DPM_EMU19, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+
+	{ .reg_offset = OMAP_MUX_TERMINATOR },
+};
+
+static struct omap_device_pad serial2_pads[] __initdata = {
+	OMAP_MUX_STATIC("uart2_cts.uart2_cts",
+			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
+	OMAP_MUX_STATIC("uart2_rts.uart2_rts",
+			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
+	OMAP_MUX_STATIC("uart2_rx.uart2_rx",
+			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
+	OMAP_MUX_STATIC("uart2_tx.uart2_tx",
+			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
+};
+
+static struct omap_device_pad serial3_pads[] __initdata = {
+	OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
+			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
+	OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
+			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
+	OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
+			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
+	OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
+			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
+};
+
+static struct omap_board_data serial2_data __initdata = {
+	.id             = 1,
+	.pads           = serial2_pads,
+	.pads_cnt       = ARRAY_SIZE(serial2_pads),
+};
+
+static struct omap_board_data serial3_data __initdata = {
+	.id             = 2,
+	.pads           = serial3_pads,
+	.pads_cnt       = ARRAY_SIZE(serial3_pads),
+};
+
+static inline void board_serial_init(void)
+{
+	omap_serial_init_port(&serial2_data);
+	omap_serial_init_port(&serial3_data);
+}
+#else
+#define board_mux	NULL
+
+static inline void board_serial_init(void)
+{
+	omap_serial_init();
+}
+#endif
+
+/* Display */
+static int pcm049_panel_enable_lcd(struct omap_dss_device *dssdev)
+{
+	return gpio_direction_output(OMAP4_PCM049_LCD_ENABLE, 1);
+}
+
+static void pcm049_panel_disable_lcd(struct omap_dss_device *dssdev)
+{
+	gpio_direction_output(OMAP4_PCM049_LCD_ENABLE, 0);
+	return;
+}
+
+/* Using generic display panel */
+static struct panel_generic_dpi_data omap4_dpi_panel = {
+	.name			= "pd050vl1",
+	.platform_enable	= pcm049_panel_enable_lcd,
+	.platform_disable	= pcm049_panel_disable_lcd,
+};
+
+struct omap_dss_device pcm049_dpi_device = {
+	.type			= OMAP_DISPLAY_TYPE_DPI,
+	.name			= "dpi",
+	.driver_name		= "generic_dpi_panel",
+	.data			= &omap4_dpi_panel,
+	.phy.dpi.data_lines	= 24,
+	.channel		= OMAP_DSS_CHANNEL_LCD2,
+};
+
+static void pcm049_dvi_mux_init(void)
+{
+	/* PAD0_HDMI_HPD_PAD1_HDMI_CEC */
+	omap_mux_init_signal("hdmi_hpd",
+			OMAP_PIN_INPUT_PULLUP);
+	omap_mux_init_signal("hdmi_cec",
+			OMAP_PIN_INPUT_PULLUP);
+	/* PAD0_HDMI_DDC_SCL_PAD1_HDMI_DDC_SDA */
+	omap_mux_init_signal("hdmi_ddc_scl",
+			OMAP_PIN_INPUT_PULLUP);
+	omap_mux_init_signal("hdmi_ddc_sda",
+			OMAP_PIN_INPUT_PULLUP);
+}
+
+static struct omap_dss_device  pcm049_dvi_device = {
+	.name = "dvi",
+	.driver_name = "hdmi_panel",
+	.type = OMAP_DISPLAY_TYPE_HDMI,
+	.clocks	= {
+		.dispc	= {
+			.dispc_fclk_src	= OMAP_DSS_CLK_SRC_FCK,
+		},
+		.hdmi	= {
+			.regn	= 15,
+			.regm2	= 1,
+		},
+	},
+	.channel = OMAP_DSS_CHANNEL_DIGIT,
+};
+
+static struct omap_dss_device *pcm049_dss_devices[] = {
+	&pcm049_dpi_device,
+	&pcm049_dvi_device,
+};
+
+static struct omap_dss_board_info pcm049_dss_data = {
+	.num_devices	= ARRAY_SIZE(pcm049_dss_devices),
+	.devices	= pcm049_dss_devices,
+	.default_device = &pcm049_dpi_device,
+};
+
+void pcm049_display_init(void)
+{
+	omap_mux_init_gpio(OMAP4_PCM049_LCD_ENABLE, OMAP_PIN_OUTPUT);
+
+	if ((gpio_request(OMAP4_PCM049_LCD_ENABLE, "DISP_ENA") == 0) &&
+		(gpio_direction_output(OMAP4_PCM049_LCD_ENABLE, 1) == 0)) {
+		gpio_export(OMAP4_PCM049_LCD_ENABLE, 0);
+		gpio_set_value(OMAP4_PCM049_LCD_ENABLE, 0);
+	} else
+		printk(KERN_ERR "could not obtain gpio for DISP_ENA");
+	pcm049_dvi_mux_init();
+	omap_display_init(&pcm049_dss_data);
+}
+
+static struct platform_device *pcm049_devices[] __initdata = {
+	&pcm049_vcc_3v3_device,
+	&leds_gpio,
+};
+
+#define	TWL_PHOENIX_DEV_ON	0x25
+
+static void pcm049_power_off(void)
+{
+	printk(KERN_INFO "Goodbye phyCORE OMAP4!\n");
+	twl_i2c_write_u8(TWL6030_MODULE_ID0, 0x7, TWL_PHOENIX_DEV_ON);
+}
+
+
+static void __init pcm049_init(void)
+{
+	pm_power_off = pcm049_power_off;
+	omap4_mux_init(board_mux, NULL, OMAP_PACKAGE_CBS);
+	pcm049_init_smsc911x();
+	pcm049_i2c_init();
+	platform_add_devices(pcm049_devices, ARRAY_SIZE(pcm049_devices));
+	board_serial_init();
+	omap4_twl6030_hsmmc_init(mmc);
+	omap4_ehci_init();
+	usb_musb_init(&musb_board_data);
+	pcm049_display_init();
+}
+
+static void __init pcm049_map_io(void)
+{
+	omap2_set_globals_443x();
+	omap44xx_map_common_io();
+}
+
+MACHINE_START(PCM049, "phyCORE OMAP4")
+	/* Maintainer: Jan Weitzel - Phytec Messtechnik GmbH */
+	.boot_params	= 0x80000100,
+	.reserve	= omap_reserve,
+	.map_io		= pcm049_map_io,
+	.init_early	= pcm049_init_early,
+	.init_irq	= gic_init_irq,
+	.init_machine	= pcm049_init,
+	.timer		= &omap_timer,
+MACHINE_END