ARM: AT91: update gpio implementation

index ecdd54d..fe00dce 100644
@@ -296,19 +296,19 @@ void __init at91cap9_set_console_clock(int id)
 static struct at91_gpio_bank at91cap9_gpio[] = {
 	{
 		.id		= AT91CAP9_ID_PIOABCD,
-		.offset		= AT91_PIOA,
+		.regbase	= AT91CAP9_BASE_PIOA,
 		.clock		= &pioABCD_clk,
 	}, {
 		.id		= AT91CAP9_ID_PIOABCD,
-		.offset		= AT91_PIOB,
+		.regbase	= AT91CAP9_BASE_PIOB,
 		.clock		= &pioABCD_clk,
 	}, {
 		.id		= AT91CAP9_ID_PIOABCD,
-		.offset		= AT91_PIOC,
+		.regbase	= AT91CAP9_BASE_PIOC,
 		.clock		= &pioABCD_clk,
 	}, {
 		.id		= AT91CAP9_ID_PIOABCD,
-		.offset		= AT91_PIOD,
+		.regbase	= AT91CAP9_BASE_PIOD,
 		.clock		= &pioABCD_clk,
 	}
 };

index 713d3bd..8ce8675 100644
@@ -271,19 +271,19 @@ void __init at91rm9200_set_console_clock(int id)
 static struct at91_gpio_bank at91rm9200_gpio[] = {
 	{
 		.id		= AT91RM9200_ID_PIOA,
-		.offset		= AT91_PIOA,
+		.regbase	= AT91RM9200_BASE_PIOA,
 		.clock		= &pioA_clk,
 	}, {
 		.id		= AT91RM9200_ID_PIOB,
-		.offset		= AT91_PIOB,
+		.regbase	= AT91RM9200_BASE_PIOB,
 		.clock		= &pioB_clk,
 	}, {
 		.id		= AT91RM9200_ID_PIOC,
-		.offset		= AT91_PIOC,
+		.regbase	= AT91RM9200_BASE_PIOC,
 		.clock		= &pioC_clk,
 	}, {
 		.id		= AT91RM9200_ID_PIOD,
-		.offset		= AT91_PIOD,
+		.regbase	= AT91RM9200_BASE_PIOD,
 		.clock		= &pioD_clk,
 	}
 };

index a9be758..d7ad3e0 100644
@@ -265,15 +265,15 @@ void __init at91sam9260_set_console_clock(int id)
 static struct at91_gpio_bank at91sam9260_gpio[] = {
 	{
 		.id		= AT91SAM9260_ID_PIOA,
-		.offset		= AT91_PIOA,
+		.regbase	= AT91SAM9260_BASE_PIOA,
 		.clock		= &pioA_clk,
 	}, {
 		.id		= AT91SAM9260_ID_PIOB,
-		.offset		= AT91_PIOB,
+		.regbase	= AT91SAM9260_BASE_PIOB,
 		.clock		= &pioB_clk,
 	}, {
 		.id		= AT91SAM9260_ID_PIOC,
-		.offset		= AT91_PIOC,
+		.regbase	= AT91SAM9260_BASE_PIOC,
 		.clock		= &pioC_clk,
 	}
 };

index 658a518..574aa6b 100644
@@ -254,15 +254,15 @@ void __init at91sam9261_set_console_clock(int id)
 static struct at91_gpio_bank at91sam9261_gpio[] = {
 	{
 		.id		= AT91SAM9261_ID_PIOA,
-		.offset		= AT91_PIOA,
+		.regbase	= AT91SAM9261_BASE_PIOA,
 		.clock		= &pioA_clk,
 	}, {
 		.id		= AT91SAM9261_ID_PIOB,
-		.offset		= AT91_PIOB,
+		.regbase	= AT91SAM9261_BASE_PIOB,
 		.clock		= &pioB_clk,
 	}, {
 		.id		= AT91SAM9261_ID_PIOC,
-		.offset		= AT91_PIOC,
+		.regbase	= AT91SAM9261_BASE_PIOC,
 		.clock		= &pioC_clk,
 	}
 };

index f83fbb0..dee0ed7 100644
@@ -266,23 +266,23 @@ void __init at91sam9263_set_console_clock(int id)
 static struct at91_gpio_bank at91sam9263_gpio[] = {
 	{
 		.id		= AT91SAM9263_ID_PIOA,
-		.offset		= AT91_PIOA,
+		.regbase	= AT91SAM9263_BASE_PIOA,
 		.clock		= &pioA_clk,
 	}, {
 		.id		= AT91SAM9263_ID_PIOB,
-		.offset		= AT91_PIOB,
+		.regbase	= AT91SAM9263_BASE_PIOB,
 		.clock		= &pioB_clk,
 	}, {
 		.id		= AT91SAM9263_ID_PIOCDE,
-		.offset		= AT91_PIOC,
+		.regbase	= AT91SAM9263_BASE_PIOC,
 		.clock		= &pioCDE_clk,
 	}, {
 		.id		= AT91SAM9263_ID_PIOCDE,
-		.offset		= AT91_PIOD,
+		.regbase	= AT91SAM9263_BASE_PIOD,
 		.clock		= &pioCDE_clk,
 	}, {
 		.id		= AT91SAM9263_ID_PIOCDE,
-		.offset		= AT91_PIOE,
+		.regbase	= AT91SAM9263_BASE_PIOE,
 		.clock		= &pioCDE_clk,
 	}
 };

index 8f5db7b..753df63 100644
@@ -282,23 +282,23 @@ void __init at91sam9g45_set_console_clock(int id)
 static struct at91_gpio_bank at91sam9g45_gpio[] = {
 	{
 		.id		= AT91SAM9G45_ID_PIOA,
-		.offset		= AT91_PIOA,
+		.regbase	= AT91SAM9G45_BASE_PIOA,
 		.clock		= &pioA_clk,
 	}, {
 		.id		= AT91SAM9G45_ID_PIOB,
-		.offset		= AT91_PIOB,
+		.regbase	= AT91SAM9G45_BASE_PIOB,
 		.clock		= &pioB_clk,
 	}, {
 		.id		= AT91SAM9G45_ID_PIOC,
-		.offset		= AT91_PIOC,
+		.regbase	= AT91SAM9G45_BASE_PIOC,
 		.clock		= &pioC_clk,
 	}, {
 		.id		= AT91SAM9G45_ID_PIODE,
-		.offset		= AT91_PIOD,
+		.regbase	= AT91SAM9G45_BASE_PIOD,
 		.clock		= &pioDE_clk,
 	}, {
 		.id		= AT91SAM9G45_ID_PIODE,
-		.offset		= AT91_PIOE,
+		.regbase	= AT91SAM9G45_BASE_PIOE,
 		.clock		= &pioDE_clk,
 	}
 };

index a238105..c4004e2 100644
@@ -246,19 +246,19 @@ void __init at91sam9rl_set_console_clock(int id)
 static struct at91_gpio_bank at91sam9rl_gpio[] = {
 	{
 		.id		= AT91SAM9RL_ID_PIOA,
-		.offset		= AT91_PIOA,
+		.regbase	= AT91SAM9RL_BASE_PIOA,
 		.clock		= &pioA_clk,
 	}, {
 		.id		= AT91SAM9RL_ID_PIOB,
-		.offset		= AT91_PIOB,
+		.regbase	= AT91SAM9RL_BASE_PIOB,
 		.clock		= &pioB_clk,
 	}, {
 		.id		= AT91SAM9RL_ID_PIOC,
-		.offset		= AT91_PIOC,
+		.regbase	= AT91SAM9RL_BASE_PIOC,
 		.clock		= &pioC_clk,
 	}, {
 		.id		= AT91SAM9RL_ID_PIOD,
-		.offset		= AT91_PIOD,
+		.regbase	= AT91SAM9RL_BASE_PIOD,
 		.clock		= &pioD_clk,
 	}
 };

index 938b34f..11d7297 100644
@@ -65,7 +65,7 @@ extern void at91sam9_alt_reset(void);
 
 struct at91_gpio_bank {
 	unsigned short id;		/* peripheral ID */
-	unsigned long offset;		/* offset from system peripheral base */
+	unsigned long regbase;		/* offset from system peripheral base */
 	struct clk *clock;		/* associated clock */
 };
 extern void __init at91_gpio_init(struct at91_gpio_bank *, int nr_banks);

index 4615528..04beff1 100644
@@ -616,8 +616,12 @@ void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks)
 
 		at91_gpio->bank = &data[i];
 		at91_gpio->chip.base = PIN_BASE + i * 32;
-		at91_gpio->regbase = at91_gpio->bank->offset +
-			(void __iomem *)AT91_VA_BASE_SYS;
+
+		at91_gpio->regbase = ioremap(at91_gpio->bank->regbase, 512);
+		if (!at91_gpio->regbase) {
+			pr_err("at91_gpio.%d, failed to map registers, ignoring.\n", i);
+			continue;
+		}
 
 		/* enable PIO controller's clock */
 		clk_enable(at91_gpio->bank->clock);

index c5df1e8..f65d083 100644
@@ -88,10 +88,6 @@
 #define AT91_DMA	(0xffffec00 - AT91_BASE_SYS)
 #define AT91_DBGU	(0xffffee00 - AT91_BASE_SYS)
 #define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
-#define AT91_PIOA	(0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOB	(0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOC	(0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOD	(0xfffff800 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
 #define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
 #define AT91_SHDWC	(0xfffffd10 - AT91_BASE_SYS)

@@ -102,6 +98,11 @@
 			(0xfffffd50 - AT91_BASE_SYS) :	\
 			(0xfffffd60 - AT91_BASE_SYS))
 
+#define AT91CAP9_BASE_PIOA	0xfffff200
+#define AT91CAP9_BASE_PIOB	0xfffff400
+#define AT91CAP9_BASE_PIOC	0xfffff600
+#define AT91CAP9_BASE_PIOD	0xfffff800
+
 #define AT91_USART0	AT91CAP9_BASE_US0
 #define AT91_USART1	AT91CAP9_BASE_US1
 #define AT91_USART2	AT91CAP9_BASE_US2

index e4037b5..5740954 100644
@@ -81,15 +81,16 @@
  */
 #define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)	/* Advanced Interrupt Controller */
 #define AT91_DBGU	(0xfffff200 - AT91_BASE_SYS)	/* Debug Unit */
-#define AT91_PIOA	(0xfffff400 - AT91_BASE_SYS)	/* PIO Controller A */
-#define AT91_PIOB	(0xfffff600 - AT91_BASE_SYS)	/* PIO Controller B */
-#define AT91_PIOC	(0xfffff800 - AT91_BASE_SYS)	/* PIO Controller C */
-#define AT91_PIOD	(0xfffffa00 - AT91_BASE_SYS)	/* PIO Controller D */
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)	/* Power Management Controller */
 #define AT91_ST		(0xfffffd00 - AT91_BASE_SYS)	/* System Timer */
 #define AT91_RTC	(0xfffffe00 - AT91_BASE_SYS)	/* Real-Time Clock */
 #define AT91_MC		(0xffffff00 - AT91_BASE_SYS)	/* Memory Controllers */
 
+#define AT91RM9200_BASE_PIOA	0xfffff400	/* PIO Controller A */
+#define AT91RM9200_BASE_PIOB	0xfffff600	/* PIO Controller B */
+#define AT91RM9200_BASE_PIOC	0xfffff800	/* PIO Controller C */
+#define AT91RM9200_BASE_PIOD	0xfffffa00	/* PIO Controller D */
+
 #define AT91_USART0	AT91RM9200_BASE_US0
 #define AT91_USART1	AT91RM9200_BASE_US1
 #define AT91_USART2	AT91RM9200_BASE_US2

index 9a79116..1bea3dc 100644
@@ -87,9 +87,6 @@
 #define AT91_CCFG	(0xffffef10 - AT91_BASE_SYS)
 #define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
 #define AT91_DBGU	(0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOA	(0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOB	(0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOC	(0xfffff800 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
 #define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
 #define AT91_SHDWC	(0xfffffd10 - AT91_BASE_SYS)

@@ -98,6 +95,10 @@
 #define AT91_WDT	(0xfffffd40 - AT91_BASE_SYS)
 #define AT91_GPBR	(0xfffffd50 - AT91_BASE_SYS)
 
+#define AT91SAM9260_BASE_PIOA	0xfffff400
+#define AT91SAM9260_BASE_PIOB	0xfffff600
+#define AT91SAM9260_BASE_PIOC	0xfffff800
+
 #define AT91_USART0	AT91SAM9260_BASE_US0
 #define AT91_USART1	AT91SAM9260_BASE_US1
 #define AT91_USART2	AT91SAM9260_BASE_US2

index ce59620..17ae9c7 100644
@@ -70,9 +70,6 @@
 #define AT91_MATRIX	(0xffffee00 - AT91_BASE_SYS)
 #define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
 #define AT91_DBGU	(0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOA	(0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOB	(0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOC	(0xfffff800 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
 #define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
 #define AT91_SHDWC	(0xfffffd10 - AT91_BASE_SYS)

@@ -81,6 +78,10 @@
 #define AT91_WDT	(0xfffffd40 - AT91_BASE_SYS)
 #define AT91_GPBR	(0xfffffd50 - AT91_BASE_SYS)
 
+#define AT91SAM9261_BASE_PIOA	0xfffff400
+#define AT91SAM9261_BASE_PIOB	0xfffff600
+#define AT91SAM9261_BASE_PIOC	0xfffff800
+
 #define AT91_USART0	AT91SAM9261_BASE_US0
 #define AT91_USART1	AT91SAM9261_BASE_US1
 #define AT91_USART2	AT91SAM9261_BASE_US2

index f1b9296..dd54079 100644
@@ -84,11 +84,6 @@
 #define AT91_CCFG	(0xffffed10 - AT91_BASE_SYS)
 #define AT91_DBGU	(0xffffee00 - AT91_BASE_SYS)
 #define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
-#define AT91_PIOA	(0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOB	(0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOC	(0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOD	(0xfffff800 - AT91_BASE_SYS)
-#define AT91_PIOE	(0xfffffa00 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
 #define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
 #define AT91_SHDWC	(0xfffffd10 - AT91_BASE_SYS)

@@ -98,6 +93,12 @@
 #define AT91_RTT1	(0xfffffd50 - AT91_BASE_SYS)
 #define AT91_GPBR	(0xfffffd60 - AT91_BASE_SYS)
 
+#define AT91SAM9263_BASE_PIOA	0xfffff200
+#define AT91SAM9263_BASE_PIOB	0xfffff400
+#define AT91SAM9263_BASE_PIOC	0xfffff600
+#define AT91SAM9263_BASE_PIOD	0xfffff800
+#define AT91SAM9263_BASE_PIOE	0xfffffa00
+
 #define AT91_USART0	AT91SAM9263_BASE_US0
 #define AT91_USART1	AT91SAM9263_BASE_US1
 #define AT91_USART2	AT91SAM9263_BASE_US2

index 2c611b9..ec370cc 100644
@@ -94,11 +94,6 @@
 #define AT91_DMA	(0xffffec00 - AT91_BASE_SYS)
 #define AT91_DBGU	(0xffffee00 - AT91_BASE_SYS)
 #define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
-#define AT91_PIOA	(0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOB	(0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOC	(0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOD	(0xfffff800 - AT91_BASE_SYS)
-#define AT91_PIOE	(0xfffffa00 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
 #define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
 #define AT91_SHDWC	(0xfffffd10 - AT91_BASE_SYS)

@@ -108,6 +103,12 @@
 #define AT91_GPBR	(0xfffffd60 - AT91_BASE_SYS)
 #define AT91_RTC	(0xfffffdb0 - AT91_BASE_SYS)
 
+#define AT91SAM9G45_BASE_PIOA	0xfffff200
+#define AT91SAM9G45_BASE_PIOB	0xfffff400
+#define AT91SAM9G45_BASE_PIOC	0xfffff600
+#define AT91SAM9G45_BASE_PIOD	0xfffff800
+#define AT91SAM9G45_BASE_PIOE	0xfffffa00
+
 #define AT91_USART0	AT91SAM9G45_BASE_US0
 #define AT91_USART1	AT91SAM9G45_BASE_US1
 #define AT91_USART2	AT91SAM9G45_BASE_US2

index 1aabacd..d3ef11a 100644
@@ -77,10 +77,6 @@
 #define AT91_CCFG	(0xffffef10 - AT91_BASE_SYS)
 #define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
 #define AT91_DBGU	(0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOA	(0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOB	(0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOC	(0xfffff800 - AT91_BASE_SYS)
-#define AT91_PIOD	(0xfffffa00 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
 #define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
 #define AT91_SHDWC	(0xfffffd10 - AT91_BASE_SYS)

@@ -91,6 +87,11 @@
 #define AT91_GPBR	(0xfffffd60 - AT91_BASE_SYS)
 #define AT91_RTC	(0xfffffe00 - AT91_BASE_SYS)
 
+#define AT91SAM9RL_BASE_PIOA	0xfffff400
+#define AT91SAM9RL_BASE_PIOB	0xfffff600
+#define AT91SAM9RL_BASE_PIOC	0xfffff800
+#define AT91SAM9RL_BASE_PIOD	0xfffffa00
+
 #define AT91_USART0	AT91SAM9RL_BASE_US0
 #define AT91_USART1	AT91SAM9RL_BASE_US1
 #define AT91_USART2	AT91SAM9RL_BASE_US2

index 5aa5885..ebd47bf 100644
@@ -70,6 +70,7 @@ static struct at91_eth_data __initdata onearm_eth_data = {
 
 static struct at91_usbh_data __initdata onearm_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata onearm_udc_data = {

index b0c796d..68a3e90 100644
@@ -75,6 +75,7 @@ static void __init afeb9260_init_early(void)
  */
 static struct at91_usbh_data __initdata afeb9260_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 /*

@@ -82,7 +83,7 @@ static struct at91_usbh_data __initdata afeb9260_usbh_data = {
  */
 static struct at91_udc_data __initdata afeb9260_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 

@@ -143,6 +144,7 @@ static struct atmel_nand_data __initdata afeb9260_nand_data = {
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
 	.bus_width_16	= 0,
+	.det_pin	= -EINVAL,
 };
 
 

@@ -154,6 +156,7 @@ static struct at91_mmc_data __initdata afeb9260_mmc_data = {
 	.wp_pin 	= AT91_PIN_PC4,
 	.slot_b		= 1,
 	.wire4		= 1,
+	.vcc_pin	= -EINVAL,
 };
 
 

@@ -174,6 +177,8 @@ static struct i2c_board_info __initdata afeb9260_i2c_devices[] = {
 static struct at91_cf_data afeb9260_cf_data = {
 	.chipselect = 4,
 	.irq_pin    = AT91_PIN_PA6,
+	.det_pin	= -EINVAL,
+	.vcc_pin	= -EINVAL,
 	.rst_pin    = AT91_PIN_PA7,
 	.flags      = AT91_CF_TRUE_IDE,
 };

index d1abd58..73f105b 100644
@@ -62,6 +62,7 @@ static void __init cam60_init_early(void)
  */
 static struct at91_usbh_data __initdata cam60_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 

@@ -141,7 +142,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata cam60_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-	// .det_pin	= ... not there
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PA9,
 	.enable_pin	= AT91_PIN_PA7,
 	.partition_info	= nand_partitions,

index 679b0b7..22b62a4 100644
@@ -70,6 +70,7 @@ static void __init cap9adk_init_early(void)
  */
 static struct at91_usbh_data __initdata cap9adk_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 /*

@@ -144,9 +145,9 @@ static struct spi_board_info cap9adk_spi_devices[] = {
  */
 static struct at91_mmc_data __initdata cap9adk_mmc_data = {
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 

@@ -154,6 +155,7 @@ static struct at91_mmc_data __initdata cap9adk_mmc_data = {
  * MACB Ethernet device
  */
 static struct at91_eth_data __initdata cap9adk_macb_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 

@@ -178,8 +180,8 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata cap9adk_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
-//	.rdy_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.rdy_pin	= -EINVAL,
 	.enable_pin	= AT91_PIN_PD15,
 	.partition_info	= nand_partitions,
 };

@@ -356,7 +358,7 @@ static struct atmel_lcdfb_info __initdata cap9adk_lcdc_data;
  * AC97
  */
 static struct ac97c_platform_data cap9adk_ac97_data = {
-//	.reset_pin	= ... not connected
+	.reset_pin	= -EINVAL,
 };
 
 

index c578c5d..eb875db 100644
@@ -64,6 +64,7 @@ static struct at91_eth_data __initdata carmeva_eth_data = {
 
 static struct at91_usbh_data __initdata carmeva_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata carmeva_udc_data = {

@@ -75,8 +76,8 @@ static struct at91_udc_data __initdata carmeva_udc_data = {
 // static struct at91_cf_data __initdata carmeva_cf_data = {
 //	.det_pin	= AT91_PIN_PB0,
 //	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
+	// .irq_pin	= -EINVAL,
+	// .vcc_pin	= -EINVAL,
 // };
 
 static struct at91_mmc_data __initdata carmeva_mmc_data = {

@@ -84,6 +85,7 @@ static struct at91_mmc_data __initdata carmeva_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PB10,
 	.wp_pin		= AT91_PIN_PC14,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct spi_board_info carmeva_spi_devices[] = {

index f4da8a1..84e5753 100644
@@ -86,6 +86,7 @@ static void __init cpu9krea_init_early(void)
  */
 static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 /*

@@ -93,13 +94,14 @@ static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
  */
 static struct at91_udc_data __initdata cpu9krea_udc_data = {
 	.vbus_pin	= AT91_PIN_PC8,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /*
  * MACB Ethernet device
  */
 static struct at91_eth_data __initdata cpu9krea_macb_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 

@@ -112,6 +114,7 @@ static struct atmel_nand_data __initdata cpu9krea_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.bus_width_16	= 0,
+	.det_pin	= -EINVAL,
 };
 
 #ifdef CONFIG_MACH_CPU9260

@@ -337,6 +340,8 @@ static struct at91_mmc_data __initdata cpu9krea_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PA29,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static void __init cpu9krea_board_init(void)

index 2d919f5..95f4b3d 100644
@@ -83,11 +83,13 @@ static void __init cpuat91_init_early(void)
 }
 
 static struct at91_eth_data __initdata cpuat91_eth_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata cpuat91_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata cpuat91_udc_data = {

@@ -98,6 +100,8 @@ static struct at91_udc_data __initdata cpuat91_udc_data = {
 static struct at91_mmc_data __initdata cpuat91_mmc_data = {
 	.det_pin	= AT91_PIN_PC2,
 	.wire4		= 1,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct physmap_flash_data cpuat91_flash_data = {

index 17654d5..e3b90cc 100644
@@ -65,11 +65,12 @@ static struct at91_eth_data __initdata csb337_eth_data = {
 
 static struct at91_usbh_data __initdata csb337_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata csb337_udc_data = {
-	// this has no VBUS sensing pin
 	.pullup_pin	= AT91_PIN_PA24,
+	.vbus_pin	= -EINVAL,
 };
 
 static struct i2c_board_info __initdata csb337_i2c_devices[] = {

@@ -98,6 +99,7 @@ static struct at91_mmc_data __initdata csb337_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PD6,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct spi_board_info csb337_spi_devices[] = {

index 72b5567..a3f717c 100644
@@ -59,6 +59,7 @@ static struct at91_eth_data __initdata csb637_eth_data = {
 
 static struct at91_usbh_data __initdata csb637_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata csb637_udc_data = {

index 01170a2..a88d1b5 100644
@@ -67,6 +67,7 @@ static struct at91_eth_data __initdata eb9200_eth_data = {
 
 static struct at91_usbh_data __initdata eb9200_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata eb9200_udc_data = {

@@ -75,15 +76,18 @@ static struct at91_udc_data __initdata eb9200_udc_data = {
 };
 
 static struct at91_cf_data __initdata eb9200_cf_data = {
+	.irq_pin	= -EINVAL,
 	.det_pin	= AT91_PIN_PB0,
+	.vcc_pin	= -EINVAL,
 	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
 };
 
 static struct at91_mmc_data __initdata eb9200_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct i2c_board_info __initdata eb9200_i2c_devices[] = {

index 7c0313c..5847823 100644
@@ -71,11 +71,15 @@ static struct at91_eth_data __initdata ecb_at91eth_data = {
 
 static struct at91_usbh_data __initdata ecb_at91usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 static struct at91_mmc_data __initdata ecb_at91mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 

index 8252c72..e203ccc 100644
@@ -54,6 +54,7 @@ static struct at91_eth_data __initdata eco920_eth_data = {
 
 static struct at91_usbh_data __initdata eco920_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata eco920_udc_data = {

@@ -64,6 +65,9 @@ static struct at91_udc_data __initdata eco920_udc_data = {
 static struct at91_mmc_data __initdata eco920_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 0,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct physmap_flash_data eco920_flash_data = {

index 4c3f65d..40d896a 100644
@@ -52,12 +52,13 @@ static void __init flexibity_init_early(void)
 /* USB Host port */
 static struct at91_usbh_data __initdata flexibity_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 /* USB Device port */
 static struct at91_udc_data __initdata flexibity_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /* SPI devices */

@@ -76,6 +77,7 @@ static struct at91_mmc_data __initdata flexibity_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC9,
 	.wp_pin		= AT91_PIN_PC4,
+	.vcc_pin	= -EINVAL,
 };
 
 /* LEDs */

index f27d1a7..1f2d55b 100644
@@ -106,6 +106,7 @@ static void __init foxg20_init_early(void)
  */
 static struct at91_usbh_data __initdata foxg20_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 /*

@@ -113,7 +114,7 @@ static struct at91_usbh_data __initdata foxg20_usbh_data = {
  */
 static struct at91_udc_data __initdata foxg20_udc_data = {
 	.vbus_pin	= AT91_PIN_PC6,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 

@@ -147,6 +148,9 @@ static struct at91_eth_data __initdata foxg20_macb_data = {
 static struct at91_mmc_data __initdata foxg20_mmc_data = {
 	.slot_b		= 1,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 

index 2e95949..7eb8eae 100644
@@ -80,6 +80,7 @@ static void __init gsia18s_init_early(void)
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 /*

@@ -87,7 +88,7 @@ static struct at91_usbh_data __initdata usbh_data = {
  */
 static struct at91_udc_data __initdata udc_data = {
 	.vbus_pin	= AT91_PIN_PA22,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /*

@@ -530,6 +531,7 @@ static struct i2c_board_info __initdata gsia18s_i2c_devices[] = {
 static struct at91_cf_data __initdata gsia18s_cf1_data = {
 	.irq_pin	= AT91_PIN_PA27,
 	.det_pin	= AT91_PIN_PB30,
+	.vcc_pin	= -EINVAL,
 	.rst_pin	= AT91_PIN_PB31,
 	.chipselect	= 5,
 	.flags		= AT91_CF_TRUE_IDE,

index 4a17089..18d46d0 100644
@@ -68,6 +68,7 @@ static struct at91_eth_data __initdata kafa_eth_data = {
 
 static struct at91_usbh_data __initdata kafa_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata kafa_udc_data = {

index 9dc8d49..e0c4d98 100644
@@ -76,6 +76,7 @@ static struct at91_eth_data __initdata kb9202_eth_data = {
 
 static struct at91_usbh_data __initdata kb9202_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata kb9202_udc_data = {

@@ -87,6 +88,8 @@ static struct at91_mmc_data __initdata kb9202_mmc_data = {
 	.det_pin	= AT91_PIN_PB2,
 	.slot_b		= 0,
 	.wire4		= 1,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct mtd_partition __initdata kb9202_nand_partition[] = {

@@ -106,7 +109,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata kb9202_nand_data = {
 	.ale		= 22,
 	.cle		= 21,
-	// .det_pin	= ... not there
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC29,
 	.enable_pin	= AT91_PIN_PC28,
 	.partition_info	= nand_partitions,

index 9bc6ab3..2451b98 100644
@@ -79,7 +79,7 @@ static struct at91_usbh_data __initdata neocore926_usbh_data = {
  */
 static struct at91_udc_data __initdata neocore926_udc_data = {
 	.vbus_pin	= AT91_PIN_PA25,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 

@@ -149,6 +149,7 @@ static struct at91_mmc_data __initdata neocore926_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PE18,
 	.wp_pin		= AT91_PIN_PE19,
+	.vcc_pin	= -EINVAL,
 };
 
 

@@ -195,6 +196,7 @@ static struct atmel_nand_data __initdata neocore926_nand_data = {
 	.rdy_pin_active_low	= 1,
 	.enable_pin		= AT91_PIN_PD15,
 	.partition_info		= nand_partitions,
+	.det_pin		= -EINVAL,
 };
 
 static struct sam9_smc_config __initdata neocore926_nand_smc_config = {

index 49e3f69..4724595 100644
@@ -107,6 +107,7 @@ static void __init add_device_pcontrol(void)
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 

index b7b8390..8155208 100644
@@ -67,6 +67,7 @@ static struct at91_eth_data __initdata picotux200_eth_data = {
 
 static struct at91_usbh_data __initdata picotux200_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 static struct at91_mmc_data __initdata picotux200_mmc_data = {

@@ -74,6 +75,7 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PA17,
+	.vcc_pin	= -EINVAL,
 };
 
 #define PICOTUX200_FLASH_BASE	AT91_CHIPSELECT_0

index 81f9110..4299421 100644
@@ -77,6 +77,7 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 /*

@@ -84,7 +85,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /*

@@ -139,7 +140,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,

@@ -177,9 +178,9 @@ static void __init ek_add_device_nand(void)
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 /*

index 6f08faa..d791683 100644
@@ -72,6 +72,7 @@ static struct at91_eth_data __initdata dk_eth_data = {
 
 static struct at91_usbh_data __initdata dk_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata dk_udc_data = {

@@ -80,16 +81,19 @@ static struct at91_udc_data __initdata dk_udc_data = {
 };
 
 static struct at91_cf_data __initdata dk_cf_data = {
+	.irq_pin	= -EINVAL,
 	.det_pin	= AT91_PIN_PB0,
+	.vcc_pin	= -EINVAL,
 	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
 };
 
 #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
 static struct at91_mmc_data __initdata dk_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 

@@ -149,7 +153,7 @@ static struct atmel_nand_data __initdata dk_nand_data = {
 	.cle		= 21,
 	.det_pin	= AT91_PIN_PB1,
 	.rdy_pin	= AT91_PIN_PC2,
-	// .enable_pin	= ... not there
+	.enable_pin	= -EINVAL,
 	.partition_info	= nand_partitions,
 };
 

index 85bcccd..242ed49 100644
@@ -72,6 +72,7 @@ static struct at91_eth_data __initdata ek_eth_data = {
 
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata ek_udc_data = {

@@ -85,6 +86,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PA17,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 

index 4d3a02f..00cf076 100644
@@ -72,6 +72,7 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 /*

@@ -79,7 +80,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 

@@ -140,7 +141,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,

@@ -181,7 +182,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC8,
 	.wp_pin		= AT91_PIN_PC4,
-//	.vcc_pin	= ... not connected
+	.vcc_pin	= -EINVAL,
 };
 
 static void __init ek_board_init(void)

index 8a50c3e..8f89951 100644
@@ -75,6 +75,7 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 /*

@@ -82,7 +83,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 

@@ -182,7 +183,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,

@@ -228,9 +229,9 @@ static void __init ek_add_device_nand(void)
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 1,
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 

index 5096a0e..e778d2c 100644
@@ -151,6 +151,7 @@ static void __init ek_add_device_dm9000(void) {}
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 

@@ -159,7 +160,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PB29,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 

@@ -188,7 +189,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 22,
 	.cle		= 21,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC15,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,

@@ -350,6 +351,9 @@ static struct spi_board_info ek_spi_devices[] = {
  */
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 #endif /* CONFIG_SPI_ATMEL_* */

index ea8f185..814381a 100644
@@ -81,7 +81,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PA25,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 

@@ -151,7 +151,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PE18,
 	.wp_pin		= AT91_PIN_PE19,
-//	.vcc_pin	= ... not connected
+	.vcc_pin	= -EINVAL,
 };
 
 

@@ -189,7 +189,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PA22,
 	.enable_pin	= AT91_PIN_PD15,
 	.partition_info	= nand_partitions,

@@ -358,6 +358,7 @@ static void __init ek_add_device_buttons(void) {}
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -EINVAL,
 };
 
 

index 817f59d..b3ec5e6 100644
@@ -86,6 +86,7 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 /*

@@ -93,7 +94,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 

@@ -170,6 +171,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
+	.det_pin	= -EINVAL,
 };
 
 static struct sam9_smc_config __initdata ek_nand_smc_config = {

@@ -215,6 +217,7 @@ static struct mci_platform_data __initdata ek_mmc_data = {
 	.slot[1] = {
 		.bus_width	= 4,
 		.detect_pin	= AT91_PIN_PC9,
+		.wp_pin		= -1;
 	},
 
 };

@@ -223,6 +226,8 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 1,	/* Only one slot so use slot B */
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC9,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 

@@ -232,6 +237,7 @@ static void __init ek_add_device_mmc(void)
 	if (ek_have_2mmc()) {
 		ek_mmc_data.slot[0].bus_width = 4;
 		ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2;
+		ek_mmc_data.slot[0].wp_pin = -1;
 	}
 	at91_add_device_mci(0, &ek_mmc_data);
 #else

index ad234cc..3c36f9f 100644
@@ -100,6 +100,7 @@ static struct mci_platform_data __initdata mci0_data = {
 	.slot[0] = {
 		.bus_width	= 4,
 		.detect_pin	= AT91_PIN_PD10,
+		.wp_pin		= -1;
 	},
 };
 

@@ -150,6 +151,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC8,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
+	.det_pin	= -EINVAL,
 };
 
 static struct sam9_smc_config __initdata ek_nand_smc_config = {

@@ -335,6 +337,7 @@ static void __init ek_add_device_buttons(void) {}
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -EINVAL,
 };
 
 

index 4f14b54..39fc576 100644
@@ -67,8 +67,8 @@ static struct usba_platform_data __initdata ek_usba_udc_data = {
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PA15,
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 

@@ -97,7 +97,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PD17,
 	.enable_pin	= AT91_PIN_PB6,
 	.partition_info	= nand_partitions,

@@ -209,6 +209,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data;
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -EINVAL,
 };
 
 

index c73d25e..17dae50 100644
@@ -57,15 +57,18 @@ static void __init snapper9260_init_early(void)
 
 static struct at91_usbh_data __initdata snapper9260_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata snapper9260_udc_data = {
 	.vbus_pin		= SNAPPER9260_IO_EXP_GPIO(5),
 	.vbus_active_low	= 1,
 	.vbus_polled		= 1,
+	.pullup_pin		= -EINVAL,
 };
 
 static struct at91_eth_data snapper9260_macb_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 

@@ -110,6 +113,8 @@ static struct atmel_nand_data __initdata snapper9260_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.partition_info	= snapper9260_nand_partition_info,
 	.bus_width_16	= 0,
+	.enable_pin	= -EINVAL,
+	.det_pin	= -EINVAL,
 };
 
 static struct sam9_smc_config __initdata snapper9260_nand_smc_config = {

index 936e5fd..3c0cc86 100644
@@ -85,6 +85,7 @@ static struct atmel_nand_data __initdata nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.bus_width_16	= 0,
+	.det_pin	= -EINVAL,
 };
 
 static struct sam9_smc_config __initdata nand_smc_config = {

@@ -122,12 +123,17 @@ static void __init add_device_nand(void)
 static struct mci_platform_data __initdata mmc_data = {
 	.slot[0] = {
 		.bus_width	= 4,
+		.detect_pin	= -1;
+		.wp_pin		= -1;
 	},
 };
 #else
 static struct at91_mmc_data __initdata mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 

@@ -137,6 +143,7 @@ static struct at91_mmc_data __initdata mmc_data = {
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 

@@ -145,12 +152,12 @@ static struct at91_usbh_data __initdata usbh_data = {
  */
 static struct at91_udc_data __initdata portuxg20_udc_data = {
 	.vbus_pin	= AT91_PIN_PC7,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 static struct at91_udc_data __initdata stamp9g20evb_udc_data = {
 	.vbus_pin	= AT91_PIN_PA22,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 

index 260260b..e5e78dd 100644
@@ -66,6 +66,7 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
 };
 
 /*

@@ -73,7 +74,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PB11,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 static void __init ek_add_device_udc(void)

@@ -199,7 +200,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PA22,
 	.enable_pin	= AT91_PIN_PD15,
 	.partition_info	= nand_partitions,

index 95edcbd..ecb8378 100644
@@ -120,6 +120,7 @@ static struct at91_eth_data __initdata yl9200_eth_data = {
  */
 static struct at91_usbh_data __initdata yl9200_usbh_data = {
 	.ports			= 1,	/* PQFP version of AT91RM9200 */
+	.vbus_pin		= {-EINVAL, -EINVAL},
 };
 
 /*

@@ -137,8 +138,9 @@ static struct at91_udc_data __initdata yl9200_udc_data = {
  */
 static struct at91_mmc_data __initdata yl9200_mmc_data = {
 	.det_pin	= AT91_PIN_PB9,
-	// .wp_pin	= ... not connected
 	.wire4		= 1,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 /*

@@ -181,7 +183,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata yl9200_nand_data = {
 	.ale		= 6,
 	.cle		= 7,
-	// .det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC14,	/* R/!B (Sheet10) */
 	.enable_pin	= AT91_PIN_PC15,	/* !CE  (Sheet10) */
 	.partition_info	= nand_partitions,

index dba0d8d..2838f8b 100644
@@ -76,7 +76,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 

@@ -173,7 +173,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 	usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
 	memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
 
-	if (data && data->vbus_pin > 0) {
+	if (data && gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 		usba_udc_data.pdata.vbus_pin = data->vbus_pin;

@@ -226,7 +226,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}

@@ -326,13 +326,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	if (mmc_id == 0) {		/* MCI0 */

@@ -419,15 +419,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;

@@ -801,7 +801,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PA9, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;

index 7227755..ff90b63 100644
@@ -106,11 +106,11 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}
-	if (data->pullup_pin)
+	if (gpio_is_valid(data->pullup_pin))
 		at91_set_gpio_output(data->pullup_pin, 0);
 
 	udc_data = *data;

@@ -159,7 +159,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}

@@ -252,7 +252,7 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	);
 
 	/* input/irq */
-	if (data->irq_pin) {
+	if (gpio_is_valid(data->irq_pin)) {
 		at91_set_gpio_input(data->irq_pin, 1);
 		at91_set_deglitch(data->irq_pin, 1);
 	}

@@ -260,7 +260,7 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	at91_set_deglitch(data->det_pin, 1);
 
 	/* outputs, initially off */
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 	at91_set_gpio_output(data->rst_pin, 0);
 

@@ -320,13 +320,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */

@@ -411,15 +411,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	at91_set_A_periph(AT91_PIN_PC1, 0);		/* SMOE */

index 39f81f4..b981a5c 100644
@@ -107,7 +107,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}

@@ -160,7 +160,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}

@@ -235,13 +235,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */

@@ -322,11 +322,11 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 	for (i = 0; i < ATMEL_MCI_MAX_NR_SLOTS; i++) {
 		if (data->slot[i].bus_width) {
 			/* input/irq */
-			if (data->slot[i].detect_pin) {
+			if (gpio_is_valid(data->slot[i].detect_pin)) {
 				at91_set_gpio_input(data->slot[i].detect_pin, 1);
 				at91_set_deglitch(data->slot[i].detect_pin, 1);
 			}
-			if (data->slot[i].wp_pin)
+			if (gpio_is_valid(data->slot[i].wp_pin))
 				at91_set_gpio_input(data->slot[i].wp_pin, 1);
 
 			switch (i) {

@@ -418,15 +418,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;

@@ -1274,17 +1274,17 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 
 	at91_sys_write(AT91_MATRIX_EBICSA, csa);
 
-	if (data->rst_pin) {
+	if (gpio_is_valid(data->rst_pin)) {
 		at91_set_multi_drive(data->rst_pin, 0);
 		at91_set_gpio_output(data->rst_pin, 1);
 	}
 
-	if (data->irq_pin) {
+	if (gpio_is_valid(data->irq_pin)) {
 		at91_set_gpio_input(data->irq_pin, 0);
 		at91_set_deglitch(data->irq_pin, 1);
 	}
 
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 0);
 		at91_set_deglitch(data->det_pin, 1);
 	}

index 0f91792..0dd3960 100644
@@ -110,7 +110,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}

@@ -163,13 +163,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */

@@ -232,15 +232,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	at91_set_A_periph(AT91_PIN_PC0, 0);		/* NANDOE */

index a050f41..077d853 100644
@@ -70,7 +70,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 

@@ -117,7 +117,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}

@@ -170,7 +170,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}

@@ -270,13 +270,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	if (mmc_id == 0) {		/* MCI0 */

@@ -424,17 +424,17 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	}
 	at91_sys_write(AT91_MATRIX_EBI0CSA, ebi0_csa);
 
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
 
-	if (data->irq_pin) {
+	if (gpio_is_valid(data->irq_pin)) {
 		at91_set_gpio_input(data->irq_pin, 1);
 		at91_set_deglitch(data->irq_pin, 1);
 	}
 
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		/* initially off */
 		at91_set_gpio_output(data->vcc_pin, 0);
 

@@ -494,15 +494,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;

@@ -743,7 +743,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PB3, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;

index 600bffb..3a0daa3 100644
@@ -120,7 +120,7 @@ void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 

@@ -175,7 +175,7 @@ void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 

@@ -257,7 +257,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 	usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
 	memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
 
-	if (data && data->vbus_pin > 0) {
+	if (data && gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 		usba_udc_data.pdata.vbus_pin = data->vbus_pin;

@@ -310,7 +310,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}

@@ -443,11 +443,11 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 
 
 	/* input/irq */
-	if (data->slot[0].detect_pin) {
+	if (gpio_is_valid(data->slot[0].detect_pin)) {
 		at91_set_gpio_input(data->slot[0].detect_pin, 1);
 		at91_set_deglitch(data->slot[0].detect_pin, 1);
 	}
-	if (data->slot[0].wp_pin)
+	if (gpio_is_valid(data->slot[0].wp_pin))
 		at91_set_gpio_input(data->slot[0].wp_pin, 1);
 
 	if (mmc_id == 0) {		/* MCI0 */

@@ -550,15 +550,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;

@@ -853,7 +853,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PD6, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;

index aacb19d..56cb73d 100644
@@ -147,7 +147,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 	usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
 	memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
 
-	if (data && data->vbus_pin > 0) {
+	if (data && gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 		usba_udc_data.pdata.vbus_pin = data->vbus_pin;

@@ -201,13 +201,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */

@@ -275,15 +275,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	at91_set_A_periph(AT91_PIN_PB4, 0);		/* NANDOE */

@@ -483,7 +483,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PD4, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;

index 960c725..3915353 100644
@@ -360,7 +360,7 @@ static int __devinit pata_at91_probe(struct platform_device *pdev)
 	ap->flags |= ATA_FLAG_SLAVE_POSS;
 	ap->pio_mask = ATA_PIO4;
 
-	if (!irq) {
+	if (!gpio_is_valid(irq)) {
 		ap->flags |= ATA_FLAG_PIO_POLLING;
 		ata_port_desc(ap, "no IRQ, using PIO polling");
 	}

@@ -414,8 +414,8 @@ static int __devinit pata_at91_probe(struct platform_device *pdev)
 
 	host->private_data = info;
 
-	return ata_host_activate(host, irq ? gpio_to_irq(irq) : 0,
-			irq ? ata_sff_interrupt : NULL,
+	return ata_host_activate(host, gpio_is_valid(irq) ? gpio_to_irq(irq) : 0,
+			gpio_is_valid(irq) ? ata_sff_interrupt : NULL,
 			irq_flags, &pata_at91_sht);
 
 err_put:

index 000a78e..ba2eda3 100644
@@ -314,7 +314,7 @@ static int __init at91_ide_probe(struct platform_device *pdev)
 	apply_timings(board->chipselect, 0, ide_timing_find_mode(XFER_PIO_0), 0);
 
 	/* with GPIO interrupt we have to do quirks in handler */
-	if (board->irq_pin >= PIN_BASE)
+	if (gpio_is_valid(board->irq_pin))
 		host->irq_handler = at91_irq_handler;
 
 	host->ports[0]->select_data = board->chipselect;

index a4aa3af..7504b22 100644
@@ -741,7 +741,7 @@ static void at91_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	at91_mci_write(host, AT91_MCI_MR, (at91_mci_read(host, AT91_MCI_MR) & ~AT91_MCI_CLKDIV) | clkdiv);
 
 	/* maybe switch power to the card */
-	if (host->board->vcc_pin) {
+	if (gpio_is_valid(host->board->vcc_pin)) {
 		switch (ios->power_mode) {
 			case MMC_POWER_OFF:
 				gpio_set_value(host->board->vcc_pin, 0);

@@ -893,7 +893,7 @@ static int at91_mci_get_ro(struct mmc_host *mmc)
 {
 	struct at91mci_host *host = mmc_priv(mmc);
 
-	if (host->board->wp_pin)
+	if (gpio_is_valid(host->board->wp_pin))
 		return !!gpio_get_value(host->board->wp_pin);
 	/*
 	 * Board doesn't support read only detection; let the mmc core

@@ -987,21 +987,21 @@ static int __init at91_mci_probe(struct platform_device *pdev)
 	 * Reserve GPIOs ... board init code makes sure these pins are set
 	 * up as GPIOs with the right direction (input, except for vcc)
 	 */
-	if (host->board->det_pin) {
+	if (gpio_is_valid(host->board->det_pin)) {
 		ret = gpio_request(host->board->det_pin, "mmc_detect");
 		if (ret < 0) {
 			dev_dbg(&pdev->dev, "couldn't claim card detect pin\n");
 			goto fail4b;
 		}
 	}
-	if (host->board->wp_pin) {
+	if (gpio_is_valid(host->board->wp_pin)) {
 		ret = gpio_request(host->board->wp_pin, "mmc_wp");
 		if (ret < 0) {
 			dev_dbg(&pdev->dev, "couldn't claim wp sense pin\n");
 			goto fail4;
 		}
 	}
-	if (host->board->vcc_pin) {
+	if (gpio_is_valid(host->board->vcc_pin)) {
 		ret = gpio_request(host->board->vcc_pin, "mmc_vcc");
 		if (ret < 0) {
 			dev_dbg(&pdev->dev, "couldn't claim vcc switch pin\n");

@@ -1053,7 +1053,7 @@ static int __init at91_mci_probe(struct platform_device *pdev)
 	/*
 	 * Add host to MMC layer
 	 */
-	if (host->board->det_pin) {
+	if (gpio_is_valid(host->board->det_pin)) {
 		host->present = !gpio_get_value(host->board->det_pin);
 	}
 	else

@@ -1064,7 +1064,7 @@ static int __init at91_mci_probe(struct platform_device *pdev)
 	/*
 	 * monitor card insertion/removal if we can
 	 */
-	if (host->board->det_pin) {
+	if (gpio_is_valid(host->board->det_pin)) {
 		ret = request_irq(gpio_to_irq(host->board->det_pin),
 				at91_mmc_det_irq, 0, mmc_hostname(mmc), host);
 		if (ret)

@@ -1083,13 +1083,13 @@ fail0:
 fail1:
 	clk_put(host->mci_clk);
 fail2:
-	if (host->board->vcc_pin)
+	if (gpio_is_valid(host->board->vcc_pin))
 		gpio_free(host->board->vcc_pin);
 fail3:
-	if (host->board->wp_pin)
+	if (gpio_is_valid(host->board->wp_pin))
 		gpio_free(host->board->wp_pin);
 fail4:
-	if (host->board->det_pin)
+	if (gpio_is_valid(host->board->det_pin))
 		gpio_free(host->board->det_pin);
 fail4b:
 	if (host->buffer)

@@ -1121,7 +1121,7 @@ static int __exit at91_mci_remove(struct platform_device *pdev)
 		dma_free_coherent(&pdev->dev, MCI_BUFSIZE,
 				host->buffer, host->physical_address);
 
-	if (host->board->det_pin) {
+	if (gpio_is_valid(host->board->det_pin)) {
 		if (device_can_wakeup(&pdev->dev))
 			free_irq(gpio_to_irq(host->board->det_pin), host);
 		device_init_wakeup(&pdev->dev, 0);

@@ -1136,9 +1136,9 @@ static int __exit at91_mci_remove(struct platform_device *pdev)
 	clk_disable(host->mci_clk);			/* Disable the peripheral clock */
 	clk_put(host->mci_clk);
 
-	if (host->board->vcc_pin)
+	if (gpio_is_valid(host->board->vcc_pin))
 		gpio_free(host->board->vcc_pin);
-	if (host->board->wp_pin)
+	if (gpio_is_valid(host->board->wp_pin))
 		gpio_free(host->board->wp_pin);
 
 	iounmap(host->baseaddr);

@@ -1159,7 +1159,7 @@ static int at91_mci_suspend(struct platform_device *pdev, pm_message_t state)
 	struct at91mci_host *host = mmc_priv(mmc);
 	int ret = 0;
 
-	if (host->board->det_pin && device_may_wakeup(&pdev->dev))
+	if (gpio_is_valid(host->board->det_pin) && device_may_wakeup(&pdev->dev))
 		enable_irq_wake(host->board->det_pin);
 
 	if (mmc)

@@ -1174,7 +1174,7 @@ static int at91_mci_resume(struct platform_device *pdev)
 	struct at91mci_host *host = mmc_priv(mmc);
 	int ret = 0;
 
-	if (host->board->det_pin && device_may_wakeup(&pdev->dev))
+	if (gpio_is_valid(host->board->det_pin) && device_may_wakeup(&pdev->dev))
 		disable_irq_wake(host->board->det_pin);
 
 	if (mmc)

index 55da20c..e20ac1f 100644
@@ -113,7 +113,7 @@ static int cpu_has_dma(void)
  */
 static void atmel_nand_enable(struct atmel_nand_host *host)
 {
-	if (host->board->enable_pin)
+	if (gpio_is_valid(host->board->enable_pin))
 		gpio_set_value(host->board->enable_pin, 0);
 }
 

@@ -122,7 +122,7 @@ static void atmel_nand_enable(struct atmel_nand_host *host)
  */
 static void atmel_nand_disable(struct atmel_nand_host *host)
 {
-	if (host->board->enable_pin)
+	if (gpio_is_valid(host->board->enable_pin))
 		gpio_set_value(host->board->enable_pin, 1);
 }
 

@@ -535,7 +535,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
 	nand_chip->IO_ADDR_W = host->io_base;
 	nand_chip->cmd_ctrl = atmel_nand_cmd_ctrl;
 
-	if (host->board->rdy_pin)
+	if (gpio_is_valid(host->board->rdy_pin))
 		nand_chip->dev_ready = atmel_nand_device_ready;
 
 	regs = platform_get_resource(pdev, IORESOURCE_MEM, 1);

@@ -573,7 +573,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, host);
 	atmel_nand_enable(host);
 
-	if (host->board->det_pin) {
+	if (gpio_is_valid(host->board->det_pin)) {
 		if (gpio_get_value(host->board->det_pin)) {
 			printk(KERN_INFO "No SmartMedia card inserted.\n");
 			res = -ENXIO;

index ddb118a..205498d 100644
@@ -1758,7 +1758,7 @@ static int __init at91udc_probe(struct platform_device *pdev)
 
 	/* rm9200 needs manual D+ pullup; off by default */
 	if (cpu_is_at91rm9200()) {
-		if (udc->board.pullup_pin <= 0) {
+		if (gpio_is_valid(udc->board.pullup_pin)) {
 			DBG("no D+ pullup?\n");
 			retval = -ENODEV;
 			goto fail0;

@@ -1825,7 +1825,7 @@ static int __init at91udc_probe(struct platform_device *pdev)
 		DBG("request irq %d failed\n", udc->udp_irq);
 		goto fail1;
 	}
-	if (udc->board.vbus_pin > 0) {
+	if (gpio_is_valid(udc->board.vbus_pin)) {
 		retval = gpio_request(udc->board.vbus_pin, "udc_vbus");
 		if (retval < 0) {
 			DBG("request vbus pin failed\n");

@@ -1869,10 +1869,10 @@ static int __init at91udc_probe(struct platform_device *pdev)
 	INFO("%s version %s\n", driver_name, DRIVER_VERSION);
 	return 0;
 fail4:
-	if (udc->board.vbus_pin > 0 && !udc->board.vbus_polled)
+	if (gpio_is_valid(udc->board.vbus_pin) && !udc->board.vbus_polled)
 		free_irq(udc->board.vbus_pin, udc);
 fail3:
-	if (udc->board.vbus_pin > 0)
+	if (gpio_is_valid(udc->board.vbus_pin))
 		gpio_free(udc->board.vbus_pin);
 fail2:
 	free_irq(udc->udp_irq, udc);

@@ -1907,7 +1907,7 @@ static int __exit at91udc_remove(struct platform_device *pdev)
 
 	device_init_wakeup(&pdev->dev, 0);
 	remove_debug_file(udc);
-	if (udc->board.vbus_pin > 0) {
+	if (gpio_is_valid(udc->board.vbus_pin)) {
 		free_irq(udc->board.vbus_pin, udc);
 		gpio_free(udc->board.vbus_pin);
 	}

@@ -1951,7 +1951,7 @@ static int at91udc_suspend(struct platform_device *pdev, pm_message_t mesg)
 		enable_irq_wake(udc->udp_irq);
 
 	udc->active_suspend = wake;
-	if (udc->board.vbus_pin > 0 && !udc->board.vbus_polled && wake)
+	if (gpio_is_valid(udc->board.vbus_pin) && !udc->board.vbus_polled && wake)
 		enable_irq_wake(udc->board.vbus_pin);
 	return 0;
 }

@@ -1961,7 +1961,7 @@ static int at91udc_resume(struct platform_device *pdev)
 	struct at91_udc *udc = platform_get_drvdata(pdev);
 	unsigned long	flags;
 
-	if (udc->board.vbus_pin > 0 && !udc->board.vbus_polled &&
+	if (gpio_is_valid(udc->board.vbus_pin) && !udc->board.vbus_polled &&
 	    udc->active_suspend)
 		disable_irq_wake(udc->board.vbus_pin);
 

index e08cb10..70701f4 100644
@@ -276,7 +276,7 @@ static int ohci_hcd_at91_drv_probe(struct platform_device *pdev)
 		 * active-low power switches.
 		 */
 		for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) {
-			if (pdata->vbus_pin[i] <= 0)
+			if (!gpio_is_valid(pdata->vbus_pin[i]))
 				continue;
 			gpio_request(pdata->vbus_pin[i], "ohci_vbus");
 			gpio_direction_output(pdata->vbus_pin[i], 0);

@@ -294,7 +294,7 @@ static int ohci_hcd_at91_drv_remove(struct platform_device *pdev)
 
 	if (pdata) {
 		for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) {
-			if (pdata->vbus_pin[i] <= 0)
+			if (!gpio_is_valid(pdata->vbus_pin[i]))
 				continue;
 			gpio_direction_output(pdata->vbus_pin[i], 1);
 			gpio_free(pdata->vbus_pin[i]);

index 04beff1..e709406 100644
@@ -60,18 +60,17 @@ static int at91_gpiolib_direction_input(struct gpio_chip *chip,
 	}
 
 static struct at91_gpio_chip gpio_chip[] = {
-	AT91_GPIO_CHIP("A", 0x00 + PIN_BASE, 32),
-	AT91_GPIO_CHIP("B", 0x20 + PIN_BASE, 32),
-	AT91_GPIO_CHIP("C", 0x40 + PIN_BASE, 32),
-	AT91_GPIO_CHIP("D", 0x60 + PIN_BASE, 32),
-	AT91_GPIO_CHIP("E", 0x80 + PIN_BASE, 32),
+	AT91_GPIO_CHIP("A", 0x00, 32),
+	AT91_GPIO_CHIP("B", 0x20, 32),
+	AT91_GPIO_CHIP("C", 0x40, 32),
+	AT91_GPIO_CHIP("D", 0x60, 32),
+	AT91_GPIO_CHIP("E", 0x80, 32),
 };
 
 static int gpio_banks;
 
 static inline void __iomem *pin_to_controller(unsigned pin)
 {
-	pin -= PIN_BASE;
 	pin /= 32;
 	if (likely(pin < gpio_banks))
 		return gpio_chip[pin].regbase;

@@ -81,7 +80,6 @@ static inline void __iomem *pin_to_controller(unsigned pin)
 
 static inline unsigned pin_to_mask(unsigned pin)
 {
-	pin -= PIN_BASE;
 	return 1 << (pin % 32);
 }
 

@@ -276,8 +274,9 @@ static u32 backups[MAX_GPIO_BANKS];
 
 static int gpio_irq_set_wake(struct irq_data *d, unsigned state)
 {
-	unsigned	mask = pin_to_mask(d->irq);
-	unsigned	bank = (d->irq - PIN_BASE) / 32;
+	unsigned	pin = irq_to_gpio(d->irq);
+	unsigned	mask = pin_to_mask(pin);
+	unsigned	bank = pin / 32;
 
 	if (unlikely(bank >= MAX_GPIO_BANKS))
 		return -EINVAL;

@@ -346,8 +345,9 @@ void at91_gpio_resume(void)
 
 static void gpio_irq_mask(struct irq_data *d)
 {
-	void __iomem	*pio = pin_to_controller(d->irq);
-	unsigned	mask = pin_to_mask(d->irq);
+	unsigned	pin = irq_to_gpio(d->irq);
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
 
 	if (pio)
 		__raw_writel(mask, pio + PIO_IDR);

@@ -355,8 +355,9 @@ static void gpio_irq_mask(struct irq_data *d)
 
 static void gpio_irq_unmask(struct irq_data *d)
 {
-	void __iomem	*pio = pin_to_controller(d->irq);
-	unsigned	mask = pin_to_mask(d->irq);
+	unsigned	pin = irq_to_gpio(d->irq);
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
 
 	if (pio)
 		__raw_writel(mask, pio + PIO_IER);

@@ -384,7 +385,7 @@ static struct irq_chip gpio_irqchip = {
 
 static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
 {
-	unsigned	pin;
+	unsigned	irq_pin;
 	struct irq_data *idata = irq_desc_get_irq_data(desc);
 	struct irq_chip *chip = irq_data_get_irq_chip(idata);
 	struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(idata);

@@ -407,12 +408,12 @@ static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
 			continue;
 		}
 
-		pin = at91_gpio->chip.base;
+		irq_pin = gpio_to_irq(at91_gpio->chip.base);
 
 		while (isr) {
 			if (isr & 1)
-				generic_handle_irq(pin);
-			pin++;
+				generic_handle_irq(irq_pin);
+			irq_pin++;
 			isr >>= 1;
 		}
 	}

@@ -440,7 +441,7 @@ static int at91_gpio_show(struct seq_file *s, void *unused)
 		seq_printf(s, "%i:\t", j);
 
 		for (bank = 0; bank < gpio_banks; bank++) {
-			unsigned	pin  = PIN_BASE + (32 * bank) + j;
+			unsigned	pin  = (32 * bank) + j;
 			void __iomem	*pio = pin_to_controller(pin);
 			unsigned	mask = pin_to_mask(pin);
 

@@ -493,10 +494,10 @@ static struct lock_class_key gpio_lock_class;
  */
 void __init at91_gpio_irq_setup(void)
 {
-	unsigned		pioc, pin;
+	unsigned		pioc, irq = gpio_to_irq(0);
 	struct at91_gpio_chip	*this, *prev;
 
-	for (pioc = 0, pin = PIN_BASE, this = gpio_chip, prev = NULL;
+	for (pioc = 0, this = gpio_chip, prev = NULL;
 			pioc++ < gpio_banks;
 			prev = this, this++) {
 		unsigned	id = this->bank->id;

@@ -504,16 +505,17 @@ void __init at91_gpio_irq_setup(void)
 
 		__raw_writel(~0, this->regbase + PIO_IDR);
 
-		for (i = 0, pin = this->chip.base; i < 32; i++, pin++) {
-			irq_set_lockdep_class(pin, &gpio_lock_class);
+		for (i = 0, irq = gpio_to_irq(this->chip.base); i < 32;
+		     i++, irq++) {
+			irq_set_lockdep_class(irq, &gpio_lock_class);
 
 			/*
 			 * Can use the "simple" and not "edge" handler since it's
 			 * shorter, and the AIC handles interrupts sanely.
 			 */
-			irq_set_chip_and_handler(pin, &gpio_irqchip,
+			irq_set_chip_and_handler(irq, &gpio_irqchip,
 						 handle_simple_irq);
-			set_irq_flags(pin, IRQF_VALID);
+			set_irq_flags(irq, IRQF_VALID);
 		}
 
 		/* The toplevel handler handles one bank of GPIOs, except

@@ -526,7 +528,7 @@ void __init at91_gpio_irq_setup(void)
 		irq_set_chip_data(id, this);
 		irq_set_chained_handler(id, gpio_irq_handler);
 	}
-	pr_info("AT91: %d gpio irqs in %d banks\n", pin - PIN_BASE, gpio_banks);
+	pr_info("AT91: %d gpio irqs in %d banks\n", irq, gpio_banks);
 }
 
 /* gpiolib support */

@@ -615,7 +617,7 @@ void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks)
 		at91_gpio = &gpio_chip[i];
 
 		at91_gpio->bank = &data[i];
-		at91_gpio->chip.base = PIN_BASE + i * 32;
+		at91_gpio->chip.base = i * 32;
 
 		at91_gpio->regbase = ioremap(at91_gpio->bank->regbase, 512);
 		if (!at91_gpio->regbase) {

454 lines not on this page · raw message

index e709406..743f668 100644
@@ -528,7 +528,7 @@ void __init at91_gpio_irq_setup(void)
 		irq_set_chip_data(id, this);
 		irq_set_chained_handler(id, gpio_irq_handler);
 	}
-	pr_info("AT91: %d gpio irqs in %d banks\n", irq, gpio_banks);
+	pr_info("AT91: %d gpio irqs in %d banks\n", irq - gpio_to_irq(0), gpio_banks);
 }
 
 /* gpiolib support */