Skip to contentSkip to conversation

r8169: Add 64bit statistics

PATCH Superseded Junchang Wang 5 participants 16 messages Nov 17, 2011 – Nov 18, 2011

Subsystems (3)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 r8169: Add 64bit statistics

Switch to use ndo_get_stats64 to get 64bit statistics. Per cpu data is used to avoid lock operations.

---
 drivers/net/ethernet/realtek/r8169.c |  113 ++++++++++++++++++++++++++++------
 1 files changed, 93 insertions(+), 20 deletions(-)
drivers/net/ethernet/realtek/r8169.c +93 -20
index cdf66d6..0165646 100644
@@ -670,11 +670,31 @@ struct rtl8169_counters {
 	__le16	tx_underun;
 };
 
+struct rtl8169_pcpu_stats {
+	u64			rx_packets;
+	u64			rx_bytes;
+	u64			tx_packets;
+	u64			tx_bytes;
+	struct u64_stats_sync	syncp;
+	/*
+	 * The following variables are updated
+	 * without syncp protection.
+	 */
+	unsigned long		rx_dropped;
+	unsigned long		tx_dropped;
+	unsigned long		rx_length_errors;
+	unsigned long		rx_errors;
+	unsigned long		rx_crc_errors;
+	unsigned long		rx_fifo_errors;
+	unsigned long		rx_missed_errors;
+};
+
 struct rtl8169_private {
 	void __iomem *mmio_addr;	/* memory map physical address */
 	struct pci_dev *pci_dev;
 	struct net_device *dev;
 	struct napi_struct napi;
+	struct rtl8169_pcpu_stats __percpu *pcpu_stats;
 	spinlock_t lock;
 	u32 msg_enable;
 	u16 txd_version;
@@ -766,7 +786,9 @@ static void rtl_hw_start(struct net_device *dev);
 static int rtl8169_close(struct net_device *dev);
 static void rtl_set_rx_mode(struct net_device *dev);
 static void rtl8169_tx_timeout(struct net_device *dev);
-static struct net_device_stats *rtl8169_get_stats(struct net_device *dev);
+static struct rtnl_link_stats64 *rtl8169_get_stats64(struct net_device *dev,
+						     struct rtnl_link_stats64
+						     *stats);
 static int rtl8169_rx_interrupt(struct net_device *, struct rtl8169_private *,
 				void __iomem *, u32 budget);
 static int rtl8169_change_mtu(struct net_device *dev, int new_mtu);
@@ -3454,7 +3476,7 @@ static void rtl_disable_msi(struct pci_dev *pdev, struct rtl8169_private *tp)
 static const struct net_device_ops rtl8169_netdev_ops = {
 	.ndo_open		= rtl8169_open,
 	.ndo_stop		= rtl8169_close,
-	.ndo_get_stats		= rtl8169_get_stats,
+	.ndo_get_stats64	= rtl8169_get_stats64,
 	.ndo_start_xmit		= rtl8169_start_xmit,
 	.ndo_tx_timeout		= rtl8169_tx_timeout,
 	.ndo_validate_addr	= eth_validate_addr,
@@ -4138,6 +4160,7 @@ rtl8169_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 
 	tp->rtl_fw = RTL_FIRMWARE_UNKNOWN;
 
+	tp->pcpu_stats = alloc_percpu(struct rtl8169_pcpu_stats);
 	rc = register_netdev(dev);
 	if (rc < 0)
 		goto err_out_msi_4;
@@ -4196,6 +4219,7 @@ static void __devexit rtl8169_remove_one(struct pci_dev *pdev)
 
 	cancel_delayed_work_sync(&tp->task);
 
+	free_percpu(tp->pcpu_stats);
 	unregister_netdev(dev);
 
 	rtl_release_firmware(tp);
@@ -5310,7 +5334,7 @@ static void rtl8169_tx_clear_range(struct rtl8169_private *tp, u32 start,
 			rtl8169_unmap_tx_skb(&tp->pci_dev->dev, tx_skb,
 					     tp->TxDescArray + entry);
 			if (skb) {
-				tp->dev->stats.tx_dropped++;
+				this_cpu_inc(tp->pcpu_stats->tx_dropped);
 				dev_kfree_skb(skb);
 				tx_skb->skb = NULL;
 			}
@@ -5562,12 +5586,12 @@ err_dma_1:
 	rtl8169_unmap_tx_skb(d, tp->tx_skb + entry, txd);
 err_dma_0:
 	dev_kfree_skb(skb);
-	dev->stats.tx_dropped++;
+	this_cpu_inc(tp->pcpu_stats->tx_dropped);
 	return NETDEV_TX_OK;
 
 err_stop_0:
 	netif_stop_queue(dev);
-	dev->stats.tx_dropped++;
+	this_cpu_inc(tp->pcpu_stats->tx_dropped);
 	return NETDEV_TX_BUSY;
 }
 
@@ -5641,8 +5665,13 @@ static void rtl8169_tx_interrupt(struct net_device *dev,
 		rtl8169_unmap_tx_skb(&tp->pci_dev->dev, tx_skb,
 				     tp->TxDescArray + entry);
 		if (status & LastFrag) {
-			dev->stats.tx_packets++;
-			dev->stats.tx_bytes += tx_skb->skb->len;
+			struct rtl8169_pcpu_stats *pcpu_stats;
+
+			pcpu_stats = this_cpu_ptr(tp->pcpu_stats);
+			u64_stats_update_begin(&pcpu_stats->syncp);
+			pcpu_stats->tx_packets++;
+			pcpu_stats->tx_bytes += tx_skb->skb->len;
+			u64_stats_update_end(&pcpu_stats->syncp);
 			dev_kfree_skb(tx_skb->skb);
 			tx_skb->skb = NULL;
 		}
@@ -5728,20 +5757,21 @@ static int rtl8169_rx_interrupt(struct net_device *dev,
 		if (unlikely(status & RxRES)) {
 			netif_info(tp, rx_err, dev, "Rx ERROR. status = %08x\n",
 				   status);
-			dev->stats.rx_errors++;
+			this_cpu_inc(tp->pcpu_stats->rx_errors);
 			if (status & (RxRWT | RxRUNT))
-				dev->stats.rx_length_errors++;
+				this_cpu_inc(tp->pcpu_stats->rx_length_errors);
 			if (status & RxCRC)
-				dev->stats.rx_crc_errors++;
+				this_cpu_inc(tp->pcpu_stats->rx_crc_errors);
 			if (status & RxFOVF) {
 				rtl8169_schedule_work(dev, rtl8169_reset_task);
-				dev->stats.rx_fifo_errors++;
+				this_cpu_inc(tp->pcpu_stats->rx_fifo_errors);
 			}
 			rtl8169_mark_to_asic(desc, rx_buf_sz);
 		} else {
 			struct sk_buff *skb;
 			dma_addr_t addr = le64_to_cpu(desc->addr);
 			int pkt_size = (status & 0x00003fff) - 4;
+			struct rtl8169_pcpu_stats *pcpu_stats;
 
 			/*
 			 * The driver does not support incoming fragmented
@@ -5749,8 +5779,8 @@ static int rtl8169_rx_interrupt(struct net_device *dev,
 			 * sized frames.
 			 */
 			if (unlikely(rtl8169_fragmented_frame(status))) {
-				dev->stats.rx_dropped++;
-				dev->stats.rx_length_errors++;
+				this_cpu_inc(tp->pcpu_stats->rx_dropped);
+				this_cpu_inc(tp->pcpu_stats->rx_length_errors);
 				rtl8169_mark_to_asic(desc, rx_buf_sz);
 				continue;
 			}
@@ -5759,7 +5789,7 @@ static int rtl8169_rx_interrupt(struct net_device *dev,
 						  tp, pkt_size, addr);
 			rtl8169_mark_to_asic(desc, rx_buf_sz);
 			if (!skb) {
-				dev->stats.rx_dropped++;
+				this_cpu_inc(tp->pcpu_stats->rx_dropped);
 				continue;
 			}
 
@@ -5771,8 +5801,11 @@ static int rtl8169_rx_interrupt(struct net_device *dev,
 
 			napi_gro_receive(&tp->napi, skb);
 
-			dev->stats.rx_bytes += pkt_size;
-			dev->stats.rx_packets++;
+			pcpu_stats = this_cpu_ptr(tp->pcpu_stats);
+			u64_stats_update_begin(&pcpu_stats->syncp);
+			pcpu_stats->rx_bytes += pkt_size;
+			pcpu_stats->rx_packets++;
+			u64_stats_update_end(&pcpu_stats->syncp);
 		}
 
 		/* Work around for AMD plateform. */
@@ -5916,7 +5949,8 @@ static void rtl8169_rx_missed(struct net_device *dev, void __iomem *ioaddr)
 	if (tp->mac_version > RTL_GIGA_MAC_VER_06)
 		return;
 
-	dev->stats.rx_missed_errors += (RTL_R32(RxMissed) & 0xffffff);
+	this_cpu_add(tp->pcpu_stats->rx_missed_errors,
+		     (RTL_R32(RxMissed) & 0xffffff));
 	RTL_W32(RxMissed, 0);
 }
 
@@ -6034,16 +6068,24 @@ static void rtl_set_rx_mode(struct net_device *dev)
 }
 
 /**
- *  rtl8169_get_stats - Get rtl8169 read/write statistics
+ *  rtl8169_get_stats64 - Get rtl8169 read/write statistics
  *  @dev: The Ethernet Device to get statistics for
  *
  *  Get TX/RX statistics for rtl8169
  */
-static struct net_device_stats *rtl8169_get_stats(struct net_device *dev)
+static struct rtnl_link_stats64 *
+rtl8169_get_stats64(struct net_device *dev, struct rtnl_link_stats64 *stats)
 {
 	struct rtl8169_private *tp = netdev_priv(dev);
 	void __iomem *ioaddr = tp->mmio_addr;
+	struct rtl8169_pcpu_stats *pcpu_stats;
+	u64 rx_packets, rx_bytes, tx_packets, tx_bytes;
+	unsigned long rx_dropped = 0, tx_dropped = 0, rx_length_errors = 0;
+	unsigned long rx_errors = 0, rx_crc_errors = 0, rx_fifo_errors = 0;
+	unsigned long rx_missed_errors = 0;
 	unsigned long flags;
+	unsigned int start;
+	int i;
 
 	if (netif_running(dev)) {
 		spin_lock_irqsave(&tp->lock, flags);
@@ -6051,7 +6093,38 @@ static struct net_device_stats *rtl8169_get_stats(struct net_device *dev)
 		spin_unlock_irqrestore(&tp->lock, flags);
 	}
 
-	return &dev->stats;
+	for_each_possible_cpu(i) {
+		pcpu_stats = per_cpu_ptr(tp->pcpu_stats, i);
+		do {
+			start = u64_stats_fetch_begin_bh(&pcpu_stats->syncp);
+			rx_packets	= pcpu_stats->rx_packets;
+			rx_bytes	= pcpu_stats->rx_bytes;
+			tx_packets	= pcpu_stats->tx_packets;
+			tx_bytes	= pcpu_stats->tx_bytes;
+		} while (u64_stats_fetch_retry_bh(&pcpu_stats->syncp, start));
+
+		stats->rx_packets	+= rx_packets;
+		stats->rx_bytes		+= rx_bytes;
+		stats->tx_packets	+= tx_packets;
+		stats->tx_bytes		+= tx_bytes;
+
+		rx_dropped		+= pcpu_stats->rx_dropped;
+		tx_dropped		+= pcpu_stats->tx_dropped;
+		rx_length_errors	+= pcpu_stats->rx_length_errors;
+		rx_errors		+= pcpu_stats->rx_errors;
+		rx_crc_errors		+= pcpu_stats->rx_crc_errors;
+		rx_fifo_errors		+= pcpu_stats->rx_fifo_errors;
+		rx_missed_errors	+= pcpu_stats->rx_missed_errors;
+	}
+	stats->rx_dropped	= rx_dropped;
+	stats->tx_dropped	= tx_dropped;
+	stats->rx_length_errors = rx_length_errors;
+	stats->rx_errors	= rx_errors;
+	stats->rx_crc_errors	= rx_crc_errors;
+	stats->rx_fifo_errors	= rx_fifo_errors;
+	stats->rx_missed_errors = rx_missed_errors;
+
+	return stats;
 }
 
 static void rtl8169_net_suspend(struct net_device *dev)
#1 lore raw
Quoted 6 lines

Switch to use ndo_get_stats64 to get 64bit statistics. Per cpu data is used to avoid lock operations.

This was recently brought up in the proposed forcedeth patch. You dont need per-cpu since Tx is locked by dev->xmit_lock and rx is implicitly single threaded by NAPI. You do need to have two u64_stat_sync entries (one for Tx and one for Rx).

#2 lore raw
Quoted 2 lines

You dont need per-cpu since Tx is locked by dev->xmit_lock and rx is implicitly single threaded by NAPI.

Thanks.

Quoted 2 lines

You do need to have
two u64_stat_sync entries (one for Tx and one for Rx).

You mean Rx and Tx will perform on different cores at one moment. So I need a sync for Tx to protect tx_xxx, and another for Rx to protect rx_xxx. Is that right?

Thanks.

Signature · 1 line
--Junchang
#3 lore raw
Quoted 12 lines · Junchang Wang
Quoted 2 lines

You dont need per-cpu since Tx is locked by dev->xmit_lock and rx is implicitly single threaded by NAPI.

Thanks.

Quoted 2 lines

You do need to have
two u64_stat_sync entries (one for Tx and one for Rx).

You mean Rx and Tx will perform on different cores at one moment. So I need a sync for Tx to protect tx_xxx, and another for Rx to protect rx_xxx. Is that right?

Yes, look at sky2.c for a template

drivers/net/ethernet/marvell/sky2.c contains code like that (different syncp for rx/tx)

TX path:

                        u64_stats_update_begin(&sky2->tx_stats.syncp);
                        ++sky2->tx_stats.packets;
                        sky2->tx_stats.bytes += skb->len;
                        u64_stats_update_end(&sky2->tx_stats.syncp);

RX path:

        u64_stats_update_begin(&sky2->rx_stats.syncp);
        sky2->rx_stats.packets += packets;
        sky2->rx_stats.bytes += bytes;
        u64_stats_update_end(&sky2->rx_stats.syncp);
#4 lore raw
Quoted 12 lines

Yes, look at sky2.c for a template

drivers/net/ethernet/marvell/sky2.c contains code like that (different syncp for rx/tx)

TX path:
                       u64_stats_update_begin(&sky2->tx_stats.syncp); ++sky2->tx_stats.packets; sky2->tx_stats.bytes += skb->len; u64_stats_update_end(&sky2->tx_stats.syncp);

Quoted 7 lines

RX path:

       u64_stats_update_begin(&sky2->rx_stats.syncp); sky2->rx_stats.packets += packets; sky2->rx_stats.bytes += bytes; u64_stats_update_end(&sky2->rx_stats.syncp);

Thanks, Eric.

I'm still confused about why we need two sync entries. Please correct me if I'm wrong.

Take r8169 for example, All statistic entries are updated in rtl8169_rx_interrupt() or rtl8169_tx_interrupt(). Those two functions are called in rtl8169_poll().
As far as I know, rtl8169_poll() is protected by NAPI_STATE_SCHED bit to run on a single core at one moment. So there is not compulsory to use two sync entries.

One benefit from two sync is that readers can avoid many retries.

Thanks.

Signature · 1 line
--Junchang
#5 lore raw

The 64bit stats update sequence used to get valid counts on 32bit systems (that can't do locked 64bit memory access) seems to be:

Quoted 4 lines

    u64_stats_update_begin(&sky2->tx_stats.syncp); ++sky2->tx_stats.packets; sky2->tx_stats.bytes += skb->len; u64_stats_update_end(&sky2->tx_stats.syncp);

I'm not sure what the begin/end markers do, but they need to hold off the readers during updates and the writers during reads - this is probably expensive on the update path.

A thought that might work is for the writer to write the middle bits of the 64 bit walue to another location, eg:

       count = sky2->tx_stats.bytes + skb->len;
       sky2->tx_stats.bytes = count;
       sky2->tx_stats.bytes_check = count >> 16;

The reader then loops until the two value are consistent.

I think this doesn't even require a memory barrier in the ISR since the order of the reads an writes doesn't matter at all.

David

#6 lore raw
Quoted 20 lines · David Laight

The 64bit stats update sequence used to get valid counts on 32bit systems (that can't do locked 64bit memory access) seems to be:

Quoted 4 lines
    u64_stats_update_begin(&sky2->tx_stats.syncp);
    ++sky2->tx_stats.packets;
    sky2->tx_stats.bytes += skb->len;
    u64_stats_update_end(&sky2->tx_stats.syncp);

I'm not sure what the begin/end markers do, but they need to hold off the readers during updates and the writers during reads - this is probably expensive on the update path.

A thought that might work is for the writer to write the middle bits of the 64 bit walue to another location, eg:

       count = sky2->tx_stats.bytes + skb->len;
       sky2->tx_stats.bytes = count;
       sky2->tx_stats.bytes_check = count >> 16;
Quoted 10 lines

The reader then loops until the two value are consistent.

I think this doesn't even require a memory barrier in the ISR since the order of the reads an writes doesn't matter at all.

David

Oh well...

Before claiming all this, you really should read
include/linux/u64_stats_sync.h

This should answer all your questions.

#7 lore raw
Quoted 33 lines

From: Eric Dumazet [mailto:[email protected]]

Quoted 20 lines · David Laight

The 64bit stats update sequence used to get valid counts on 32bit systems (that can't do locked 64bit memory access) seems to be:

Quoted 4 lines
    u64_stats_update_begin(&sky2->tx_stats.syncp);
    ++sky2->tx_stats.packets;
    sky2->tx_stats.bytes += skb->len;
    u64_stats_update_end(&sky2->tx_stats.syncp);

I'm not sure what the begin/end markers do, but they need to hold off the readers during updates and the writers during reads - this is probably expensive on the update path.

A thought that might work is for the writer to write the middle bits of the 64 bit walue to another location, eg:

       count = sky2->tx_stats.bytes + skb->len;
       sky2->tx_stats.bytes = count;
       sky2->tx_stats.bytes_check = count >> 16;
Quoted 10 lines

The reader then loops until the two value are consistent.

I think this doesn't even require a memory barrier in the ISR since the order of the reads an writes doesn't matter at all.

David

Quoted 6 lines

Oh well...

Before claiming all this, you really should read
include/linux/u64_stats_sync.h

This should answer all your questions.

Ah yes ...

Both u64_stats_update_begin & _end increment a numeric field with an appropriate memory barrier. So the 'update' path has two extra read-modify-write sequences (possibly the 2nd read can be optimised out), and two smp_wmb() that may introduce bus delays.

Would be fine if it were guaranteed to work!
Consider the following sequence of events:

       u64_stats_update_begin()
       calculate 'count+1'
                                read_seqcount_begin()
                                read count_hi
       write count_lo
                                read count_lo
       write count_hi
                                read_seqcount_retry()
       ... update other counters ...
       u64_stats_update_end()

The reader gets an invalid value since it reads the same 'sequence' both times.

Could be fixed by using '|= 1' in update_begin and looping on odd values in read_seqcount_begin().

David

#8 lore raw
Quoted 20 lines · David Laight

Ah yes ...

Both u64_stats_update_begin & _end increment a numeric field with an appropriate memory barrier. So the 'update' path has two extra read-modify-write sequences (possibly the 2nd read can be optimised out), and two smp_wmb() that may introduce bus delays.

Would be fine if it were guaranteed to work!
Consider the following sequence of events:

       u64_stats_update_begin()
       calculate 'count+1'
                                read_seqcount_begin()
                                read count_hi
       write count_lo
                                read count_lo
       write count_hi
                                read_seqcount_retry()
       ... update other counters ...
       u64_stats_update_end()
Quoted 6 lines

The reader gets an invalid value since it reads the same 'sequence' both times.

Could be fixed by using '|= 1' in update_begin and looping on odd values in read_seqcount_begin().

I am a bit tired of this discussion.

You obviously dont understand how the thing is working.

Spend some time on it before claiming there are bugs.

#9 lore raw
In reply to Junchang Wang
Quoted 25 lines · Junchang Wang
Quoted 12 lines

Yes, look at sky2.c for a template

drivers/net/ethernet/marvell/sky2.c contains code like that (different syncp for rx/tx)

TX path:

                       u64_stats_update_begin(&sky2->tx_stats.syncp);
                       ++sky2->tx_stats.packets;
                       sky2->tx_stats.bytes += skb->len;
                       u64_stats_update_end(&sky2->tx_stats.syncp);
Quoted 7 lines

RX path:

       u64_stats_update_begin(&sky2->rx_stats.syncp);
       sky2->rx_stats.packets += packets;
       sky2->rx_stats.bytes += bytes;
       u64_stats_update_end(&sky2->rx_stats.syncp);

Thanks, Eric.

I'm still confused about why we need two sync entries. Please correct me if I'm wrong.

Quoted 9 lines

Take r8169 for example, All statistic entries are updated in rtl8169_rx_interrupt() or rtl8169_tx_interrupt(). Those two functions are called in rtl8169_poll().
As far as I know, rtl8169_poll() is protected by NAPI_STATE_SCHED bit to run on a single core at one moment. So there is not compulsory to use two sync entries.

One benefit from two sync is that readers can avoid many retries.

Oh well...

Dont try to optimize all this stuff, I spent some time on it already, just use the infrastructure and forget about races and bugs.

The short answer is :

CPU1 CPU2
TX path RX path

since CPU1 & CPU2 will do the update_begin(), and the memory increment is not atomic, we might lose one increment, and block a stat reader forever.

#10 lore raw
In reply to Junchang Wang
Quoted 26 lines · Junchang Wang

Switch to use ndo_get_stats64 to get 64bit statistics. Per cpu data is used to avoid lock operations.

---
 drivers/net/ethernet/realtek/r8169.c |  113 ++++++++++++++++++++++++++++------
 1 files changed, 93 insertions(+), 20 deletions(-)
drivers/net/ethernet/realtek/r8169.c +9 -0
index cdf66d6..0165646 100644
@@ -670,11 +670,31 @@ struct rtl8169_counters {
 	__le16	tx_underun;
 };
 
+struct rtl8169_pcpu_stats {
+	u64			rx_packets;
+	u64			rx_bytes;
+	u64			tx_packets;
+	u64			tx_bytes;
+	struct u64_stats_sync	syncp;
+	/*
+	 * The following variables are updated
+	 * without syncp protection.

drivers/net/ethernet/realtek/r8169.c struct rtl8169_counters { · line 691

Quoted 10 lines
drivers/net/ethernet/realtek/r8169.c +10 -0
+	 */
+	unsigned long		rx_dropped;
+	unsigned long		tx_dropped;
+	unsigned long		rx_length_errors;
+	unsigned long		rx_errors;
+	unsigned long		rx_crc_errors;
+	unsigned long		rx_fifo_errors;
+	unsigned long		rx_missed_errors;
+};
+

Thats overkill. Dont copy what have been done for virtual devices (loopback, tunnels, ...)

RX and TX path are serialized (only one cpu can fly at one moment)

#11 lore raw
Quoted 41 lines · Eric Dumazet
Quoted 26 lines · Junchang Wang

Switch to use ndo_get_stats64 to get 64bit statistics. Per cpu data is used to avoid lock operations.

---
 drivers/net/ethernet/realtek/r8169.c |  113 ++++++++++++++++++++++++++++------

 1 files changed, 93 insertions(+), 20 deletions(-)
drivers/net/ethernet/realtek/r8169.c +9 -0
index cdf66d6..0165646 100644
@@ -670,11 +670,31 @@ struct rtl8169_counters {
       __le16  tx_underun;
  };
 
+struct rtl8169_pcpu_stats {
+     u64                     rx_packets;
+     u64                     rx_bytes;
+     u64                     tx_packets;
+     u64                     tx_bytes;
+     struct u64_stats_sync   syncp;
+     /*
+      * The following variables are updated
+      * without syncp protection.

drivers/net/ethernet/realtek/r8169.c struct rtl8169_counters { · line 691

Quoted 10 lines
drivers/net/ethernet/realtek/r8169.c +10 -0
+      */
+     unsigned long           rx_dropped;
+     unsigned long           tx_dropped;
+     unsigned long           rx_length_errors;
+     unsigned long           rx_errors;
+     unsigned long           rx_crc_errors;
+     unsigned long           rx_fifo_errors;
+     unsigned long           rx_missed_errors;
+};
+

Thats overkill. Dont copy what have been done for virtual devices (loopback, tunnels, ...)

Quoted 2 lines

RX and TX path are serialized (only one cpu can fly at one moment)

Thanks. I'll submit a new version.

Signature · 1 line
--Junchang
#12 lore raw
In reply to Junchang Wang

Junchang Wang <[email protected]> :

Quoted 3 lines

Switch to use ndo_get_stats64 to get 64bit statistics. Per cpu data is used to avoid lock operations.

The 816x chipsets have hardware stats registers. The driver already use them. Please use them more.

Signature · 1 line
Ueimor
#13 lore raw
Quoted 8 lines · Francois Romieu

Junchang Wang <[email protected]> :

Quoted 3 lines

Switch to use ndo_get_stats64 to get 64bit statistics. Per cpu data is used to avoid lock operations.

The 816x chipsets have hardware stats registers. The driver already use them. Please use them more.

I would like to mention a possible bias.

I know for that tg3 includes in RX counters frames/bytes that were dropped (because napi handler couldnot keep up with the load)

They also include FCS in the byte count.

When using software counters, we can compare "ethtool -S" and "ifconfig" ones.

But generaly speaking, if hardware stats are available we should use them and save few instructions per packet ;)

#14 lore raw
In reply to Francois Romieu
Quoted 2 lines

The 816x chipsets have hardware stats registers. The driver already use them. Please use them more.

Hi Francois,

I'm not sure which hardware stats registers are accurate. Besides, it seem r8169.c are also designed for other chipsets (8129?).

I would like other people who are quite familiar with those chipsets to do this job.

Is that OK? Thanks.

Signature · 1 line
--Junchang
#15 lore raw

Junchang Wang <[email protected]> :
[...]

Quoted 1 line

I'm not sure which hardware stats registers are accurate.

See rtl8169_gstrings.

Quoted 1 line

Besides, it seem r8169.c are also designed for other chipsets (8129?).

Afaik the basic statistics are consistent through the 816x and 810{2, 3} family.

Quoted 4 lines

I would like other people who are quite familiar with those chipsets to do this job.

Is that OK ? Thanks.

Fair enough.

Eric's "ethtool -S = hardware, ip -s = software" remark makes sense anyway. So there is no reason to be retentive.

Signature · 1 line
Ueimor