Skip to contentSkip to conversation

MRST/Medfield thermal updates

PATCH New Alan Cox 1 participant 5 messages Dec 15, 2011

Subsystems (2)
lore
Share & tools
lore

Alan Cox

author
#0 lore raw

cover MRST/Medfield thermal updates

Update the thermal driver to use the MSIC MFD layer, and make sure we turn off the thermistor by default
---

Mika Westerberg (4):
x86, mrst: add msic_thermal platform support
platform-x86: intel_mid_thermal: turn off thermistor voltage by default
platform-x86: intel_mid_thermal: convert to use Intel MSIC API
platform-x86: intel_mid_thermal: add msic_thermal alias

 arch/x86/platform/mrst/mrst.c            |    6 ++++
 drivers/platform/x86/Kconfig             |    2 +
 drivers/platform/x86/intel_mid_thermal.c |   46 +++++++++++++++---------------
 3 files changed, 30 insertions(+), 24 deletions(-)
author
#1 lore raw

PATCH 1/4 platform-x86: intel_mid_thermal: add msic_thermal alias

From: Mika Westerberg <[email protected]>

In newer boards this device is called "msic_thermal" instead of "msic_sensor". To support both we add suitable alias for the driver.

---

 drivers/platform/x86/intel_mid_thermal.c |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)
drivers/platform/x86/intel_mid_thermal.c +1 -0
index ccd7b1f..de2e62e 100644
@@ -550,6 +550,7 @@ static int mid_thermal_remove(struct platform_device *pdev)
 
 static const struct platform_device_id therm_id_table[] = {
 	{ DRIVER_NAME, 1 },
+	{ "msic_thermal", 1 },
 	{ }
 };
 
author
#2 lore raw

PATCH 2/4 platform-x86: intel_mid_thermal: convert to use Intel MSIC API

In reply to Alan Cox

From: Mika Westerberg <[email protected]>

Intel MSIC MFD driver provides common register access interface to the devices in the MSIC die so we use that instead of SCU IPC.

---

 drivers/platform/x86/Kconfig             |    2 +-
 drivers/platform/x86/intel_mid_thermal.c |   39 ++++++++++++++----------------
 2 files changed, 19 insertions(+), 22 deletions(-)
drivers/platform/x86/Kconfig +1 -1
index f995e6e..7c03c4c 100644
@@ -672,7 +672,7 @@ config INTEL_MID_POWER_BUTTON
 
 config INTEL_MFLD_THERMAL
        tristate "Thermal driver for Intel Medfield platform"
-       depends on INTEL_SCU_IPC && THERMAL
+       depends on MFD_INTEL_MSIC && THERMAL
        help
          Say Y here to enable thermal driver support for the  Intel Medfield
          platform.
drivers/platform/x86/intel_mid_thermal.c +18 -21
index de2e62e..aef4979 100644
@@ -33,18 +33,15 @@
 #include <linux/slab.h>
 #include <linux/pm.h>
 #include <linux/thermal.h>
-
-#include <asm/intel_scu_ipc.h>
+#include <linux/mfd/intel_msic.h>
 
 /* Number of thermal sensors */
 #define MSIC_THERMAL_SENSORS	4
 
 /* ADC1 - thermal registers */
-#define MSIC_THERM_ADC1CNTL1	0x1C0
 #define MSIC_ADC_ENBL		0x10
 #define MSIC_ADC_START		0x08
 
-#define MSIC_THERM_ADC1CNTL3	0x1C2
 #define MSIC_ADCTHERM_ENBL	0x04
 #define MSIC_ADCRRDATA_ENBL	0x05
 #define MSIC_CHANL_MASK_VAL	0x0F
@@ -75,8 +72,8 @@
 #define ADC_VAL60C		315
 
 /* ADC base addresses */
-#define ADC_CHNL_START_ADDR	0x1C5	/* increments by 1 */
-#define ADC_DATA_START_ADDR	0x1D4	/* increments by 2 */
+#define ADC_CHNL_START_ADDR	INTEL_MSIC_ADC1ADDR0	/* increments by 1 */
+#define ADC_DATA_START_ADDR	INTEL_MSIC_ADC1SNS0H	/* increments by 2 */
 
 /* MSIC die attributes */
 #define MSIC_DIE_ADC_MIN	488
@@ -189,17 +186,17 @@ static int mid_read_temp(struct thermal_zone_device *tzd, unsigned long *temp)
 	addr = td_info->chnl_addr;
 
 	/* Enable the msic for conversion before reading */
-	ret = intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL3, MSIC_ADCRRDATA_ENBL);
+	ret = intel_msic_reg_write(INTEL_MSIC_ADC1CNTL3, MSIC_ADCRRDATA_ENBL);
 	if (ret)
 		return ret;
 
 	/* Re-toggle the RRDATARD bit (temporary workaround) */
-	ret = intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL3, MSIC_ADCTHERM_ENBL);
+	ret = intel_msic_reg_write(INTEL_MSIC_ADC1CNTL3, MSIC_ADCTHERM_ENBL);
 	if (ret)
 		return ret;
 
 	/* Read the higher bits of data */
-	ret = intel_scu_ipc_ioread8(addr, &data);
+	ret = intel_msic_reg_read(addr, &data);
 	if (ret)
 		return ret;
 
@@ -207,7 +204,7 @@ static int mid_read_temp(struct thermal_zone_device *tzd, unsigned long *temp)
 	adc_val = (data << 2);
 	addr++;
 
-	ret = intel_scu_ipc_ioread8(addr, &data);/* Read lower bits */
+	ret = intel_msic_reg_read(addr, &data);/* Read lower bits */
 	if (ret)
 		return ret;
 
@@ -235,7 +232,7 @@ static int configure_adc(int val)
 	int ret;
 	uint8_t data;
 
-	ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL1, &data);
+	ret = intel_msic_reg_read(INTEL_MSIC_ADC1CNTL1, &data);
 	if (ret)
 		return ret;
 
@@ -246,7 +243,7 @@ static int configure_adc(int val)
 		/* Just stop the ADC */
 		data &= (~MSIC_ADC_START);
 	}
-	return intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL1, data);
+	return intel_msic_reg_write(INTEL_MSIC_ADC1CNTL1, data);
 }
 
 /**
@@ -262,21 +259,21 @@ static int set_up_therm_channel(u16 base_addr)
 	int ret;
 
 	/* Enable all the sensor channels */
-	ret = intel_scu_ipc_iowrite8(base_addr, SKIN_SENSOR0_CODE);
+	ret = intel_msic_reg_write(base_addr, SKIN_SENSOR0_CODE);
 	if (ret)
 		return ret;
 
-	ret = intel_scu_ipc_iowrite8(base_addr + 1, SKIN_SENSOR1_CODE);
+	ret = intel_msic_reg_write(base_addr + 1, SKIN_SENSOR1_CODE);
 	if (ret)
 		return ret;
 
-	ret = intel_scu_ipc_iowrite8(base_addr + 2, SYS_SENSOR_CODE);
+	ret = intel_msic_reg_write(base_addr + 2, SYS_SENSOR_CODE);
 	if (ret)
 		return ret;
 
 	/* Since this is the last channel, set the stop bit
 	 * to 1 by ORing the DIE_SENSOR_CODE with 0x10 */
-	ret = intel_scu_ipc_iowrite8(base_addr + 3,
+	ret = intel_msic_reg_write(base_addr + 3,
 			(MSIC_DIE_SENSOR_CODE | 0x10));
 	if (ret)
 		return ret;
@@ -295,11 +292,11 @@ static int reset_stopbit(uint16_t addr)
 {
 	int ret;
 	uint8_t data;
-	ret = intel_scu_ipc_ioread8(addr, &data);
+	ret = intel_msic_reg_read(addr, &data);
 	if (ret)
 		return ret;
 	/* Set the stop bit to zero */
-	return intel_scu_ipc_iowrite8(addr, (data & 0xEF));
+	return intel_msic_reg_write(addr, (data & 0xEF));
 }
 
 /**
@@ -322,7 +319,7 @@ static int find_free_channel(void)
 	uint8_t data;
 
 	/* check whether ADC is enabled */
-	ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL1, &data);
+	ret = intel_msic_reg_read(INTEL_MSIC_ADC1CNTL1, &data);
 	if (ret)
 		return ret;
 
@@ -331,7 +328,7 @@ static int find_free_channel(void)
 
 	/* ADC is already enabled; Looking for an empty channel */
 	for (i = 0; i < ADC_CHANLS_MAX; i++) {
-		ret = intel_scu_ipc_ioread8(ADC_CHNL_START_ADDR + i, &data);
+		ret = intel_msic_reg_read(ADC_CHNL_START_ADDR + i, &data);
 		if (ret)
 			return ret;
 
@@ -359,7 +356,7 @@ static int mid_initialize_adc(struct device *dev)
 	 * Ensure that adctherm is disabled before we
 	 * initialize the ADC
 	 */
-	ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL3, &data);
+	ret = intel_msic_reg_read(INTEL_MSIC_ADC1CNTL3, &data);
 	if (ret)
 		return ret;
 
author
#3 lore raw

PATCH 3/4 platform-x86: intel_mid_thermal: turn off thermistor voltage by default

In reply to Alan Cox

From: Mika Westerberg <[email protected]>

Instead of complaining that the voltage is on, we can just ask the MSIC to turn the voltage off. This should save some power.

Voltage for thermistors is turned on when ADC conversion is initiated.

---

 drivers/platform/x86/intel_mid_thermal.c |    6 ++++--
 1 files changed, 4 insertions(+), 2 deletions(-)
drivers/platform/x86/intel_mid_thermal.c +4 -2
index aef4979..a4e56be 100644
@@ -360,8 +360,10 @@ static int mid_initialize_adc(struct device *dev)
 	if (ret)
 		return ret;
 
-	if (data & MSIC_ADCTHERM_MASK)
-		dev_warn(dev, "ADCTHERM already set");
+	data &= ~MSIC_ADCTHERM_MASK;
+	ret = intel_msic_reg_write(INTEL_MSIC_ADC1CNTL3, data);
+	if (ret)
+		return ret;
 
 	/* Index of the first channel in which the stop bit is set */
 	channel_index = find_free_channel();
author
#4 lore raw

PATCH 4/4 x86, mrst: add msic_thermal platform support

In reply to Alan Cox

From: Mika Westerberg <[email protected]>

This will let the MSIC driver to create platform device for the thermal driver.

---

 arch/x86/platform/mrst/mrst.c |    6 ++++++
 1 files changed, 6 insertions(+), 0 deletions(-)
arch/x86/platform/mrst/mrst.c +6 -0
index 4c2235d..a9a4732 100644
@@ -686,6 +686,11 @@ static void *msic_ocd_platform_data(void *info)
 	return msic_generic_platform_data(info, INTEL_MSIC_BLOCK_OCD);
 }
 
+static void *msic_thermal_platform_data(void *info)
+{
+	return msic_generic_platform_data(info, INTEL_MSIC_BLOCK_THERMAL);
+}
+
 static const struct devs_id __initconst device_ids[] = {
 	{"bma023", SFI_DEV_TYPE_I2C, 1, &no_platform_data},
 	{"pmic_gpio", SFI_DEV_TYPE_SPI, 1, &pmic_gpio_platform_data},
@@ -705,6 +710,7 @@ static const struct devs_id __initconst device_ids[] = {
 	{"msic_audio", SFI_DEV_TYPE_IPC, 1, &msic_audio_platform_data},
 	{"msic_power_btn", SFI_DEV_TYPE_IPC, 1, &msic_power_btn_platform_data},
 	{"msic_ocd", SFI_DEV_TYPE_IPC, 1, &msic_ocd_platform_data},
+	{"msic_thermal", SFI_DEV_TYPE_IPC, 1, &msic_thermal_platform_data},
 
 	{},
 };