mx28evk: add RTC support

PATCH New Matthias Fuchs 4 participants 18 messages Jan 18, 2012 – Feb 7, 2012

lore

Share & tools

lore

Matthias Fuchs

author

2012-01-18 11:33 UTC #0 lore raw

PATCH 1/3 mx28evk: add RTC support

This patch adds support for the MX28 internal RTC
and enables u-boot's date command.

Signed-off-by Matthias Fuchs <[email protected]>

---
 include/configs/mx28evk.h |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)

include/configs/mx28evk.h +8 -0

index bea46e7..8a752aa 100644
@@ -56,6 +56,7 @@
 #define CONFIG_CMD_FAT
 
 #define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_GPIO
 #define CONFIG_CMD_MII

@@ -150,6 +151,13 @@
 #endif
 
 /*
+ * RTC
+ */
+#ifdef	CONFIG_CMD_DATE
+#define	CONFIG_RTC_MXS
+#endif
+
+/*
  * Boot Linux
  */
 #define CONFIG_CMDLINE_TAG

Signature · 1 line

1.6.1

Matthias Fuchs

author

2012-01-18 11:33 UTC #1 lore raw

PATCH 2/3 mx28evk: add USB support

This patch enables USB host support on the MX28EVK board.

Signed-off-by Matthias Fuchs <[email protected]>

---
 board/freescale/mx28evk/mx28evk.c |    7 +++++++
 include/configs/mx28evk.h         |   12 ++++++++++++
 2 files changed, 19 insertions(+), 0 deletions(-)

board/freescale/mx28evk/mx28evk.c +7 -0

index 0d04d44..1bc83e9 100644
@@ -52,6 +52,13 @@ int board_early_init_f(void)
 	/* SSP2 clock at 96MHz */
 	mx28_set_sspclk(MXC_SSPCLK2, 96000, 0);
 
+#ifdef	CONFIG_CMD_USB
+	mxs_iomux_setup_pad(MX28_PAD_SSP2_SS1__USB1_OVERCURRENT);
+	mxs_iomux_setup_pad(MX28_PAD_AUART2_RX__GPIO_3_8 |
+			MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL);
+	gpio_direction_output(MX28_PAD_AUART2_RX__GPIO_3_8, 1);
+#endif
+
 	return 0;
 }

include/configs/mx28evk.h +12 -0

index 8a752aa..8f791aa 100644
@@ -64,6 +64,7 @@
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
 
 /*
  * Memory configurations

@@ -158,6 +159,17 @@
 #endif
 
 /*
+ * USB
+ */
+#ifdef	CONFIG_CMD_USB
+#define	CONFIG_USB_EHCI
+#define	CONFIG_USB_EHCI_MXS
+#define	CONFIG_EHCI_MXS_PORT 1
+#define	CONFIG_EHCI_IS_TDI
+#define	CONFIG_USB_STORAGE
+#endif
+
+/*
  * Boot Linux
  */
 #define CONFIG_CMDLINE_TAG

Signature · 1 line

1.6.1

Matthias Fuchs

author

2012-01-18 11:33 UTC #2 lore raw

PATCH 3/3 mx28evk: add SPI support

This patch adds SPI support for the MX28EVK. Support for an optionally installed SPI flash is also added. An example configuration for redundant envrionment from SPI flash is also added but disabled by default.

This patch has been tested on a MX28EVK Rev. D with an installed SST25VF032B 32Mbit SPI flash.

Signed-off-by Matthias Fuchs <[email protected]>

---
 board/freescale/mx28evk/iomux.c |    8 +++++++
 include/configs/mx28evk.h       |   44 ++++++++++++++++++++++++++++++++++++--
 2 files changed, 49 insertions(+), 3 deletions(-)

board/freescale/mx28evk/iomux.c +8 -0

index 904e3f3..396761b 100644
@@ -28,6 +28,7 @@
 #define	MUX_CONFIG_SSP0	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
 #define	MUX_CONFIG_ENET	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
 #define	MUX_CONFIG_EMI	(MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
+#define	MUX_CONFIG_SSP2	(MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_PULLUP)
 
 const iomux_cfg_t iomux_setup[] = {
 	/* DUART */

@@ -130,6 +131,13 @@ const iomux_cfg_t iomux_setup[] = {
 	MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
 	MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
 	MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
+
+	/* SPI2 (for SPI flash) */
+	MX28_PAD_SSP2_SCK__SSP2_SCK | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_MOSI__SSP2_CMD | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_MISO__SSP2_D0 | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_SS0__SSP2_D3 |
+		(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP),
 };
 
 void board_init_ll(void)

include/configs/mx28evk.h +41 -3

62 lines not on this page · raw message

Signature · 1 line

1.6.1

Marek Vasut

2012-01-18 16:07 UTC #3 lore raw

PATCH 3/3 mx28evk: add SPI support

Quoted 100 lines

This patch has been tested on a MX28EVK Rev. D with an installed SST25VF032B 32Mbit SPI flash.

Signed-off-by Matthias Fuchs <[email protected]>

---
 board/freescale/mx28evk/iomux.c |    8 +++++++
 include/configs/mx28evk.h       |   44

++++++++++++++++++++++++++++++++++++-- 2 files changed, 49 insertions(+), 3 deletions(-)

(quoted diff) +0 -0

b/board/freescale/mx28evk/iomux.c index 904e3f3..396761b 100644

board/freescale/mx28evk/iomux.c +8 -0

@@ -28,6 +28,7 @@
 #define	MUX_CONFIG_SSP0	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
 #define	MUX_CONFIG_ENET	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
 #define	MUX_CONFIG_EMI	(MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
+#define	MUX_CONFIG_SSP2	(MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_PULLUP)
 
 const iomux_cfg_t iomux_setup[] = {
 	/* DUART */

@@ -130,6 +131,13 @@ const iomux_cfg_t iomux_setup[] = {
 	MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
 	MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
 	MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
+
+	/* SPI2 (for SPI flash) */
+	MX28_PAD_SSP2_SCK__SSP2_SCK | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_MOSI__SSP2_CMD | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_MISO__SSP2_D0 | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_SS0__SSP2_D3 |
+		(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP),
 };
 
 void board_init_ll(void)

include/configs/mx28evk.h +34 -3

index 8f791aa..04967d7 100644
@@ -64,6 +64,8 @@
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_PING
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
 #define CONFIG_CMD_USB
 
 /*

@@ -127,9 +129,11 @@
  * MMC Driver
  */
 #define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_ENV_OFFSET	(256 * 1024)
-#define CONFIG_ENV_SIZE	(16 * 1024)
-#define CONFIG_SYS_MMC_ENV_DEV 0
+#ifdef CONFIG_ENV_IS_IN_MMC
+ #define CONFIG_ENV_OFFSET	(256 * 1024)
+ #define CONFIG_ENV_SIZE	(16 * 1024)
+ #define CONFIG_SYS_MMC_ENV_DEV 0
+#endif
 #define CONFIG_CMD_SAVEENV
 #ifdef	CONFIG_CMD_MMC
 #define CONFIG_MMC

@@ -170,6 +174,40 @@
 #endif
 
 /*
+ * SPI
+ */
+#ifdef CONFIG_CMD_SPI
+#define CONFIG_HARD_SPI
+#define CONFIG_MXS_SPI
+#define CONFIG_SPI_HALF_DUPLEX
+#define CONFIG_DEFAULT_SPI_BUS		2
+#define CONFIG_DEFAULT_SPI_MODE		SPI_MODE_0
+
+/* SPI Flash */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH
+/* this may vary and depends on the installed chip */
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+#define CONFIG_SF_DEFAULT_SPEED		24000000
+
+/* (redundant) environemnt in SPI flash */
+#undef CONFIG_ENV_IS_IN_SPI_FLASH
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_SIZE			0x1000		/* 4KB */
+#define CONFIG_ENV_OFFSET		0x40000		/* 256K */
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SECT_SIZE		0x1000
+#define CONFIG_ENV_SPI_CS		0
+#define CONFIG_ENV_SPI_BUS		2

include/configs/mx28evk.h line 213

Quoted 10 lines

include/configs/mx28evk.h +7 -0

+#define CONFIG_ENV_SPI_MAX_HZ		24000000
+#define CONFIG_ENV_SPI_MODE		SPI_MODE_0
+#endif
+#endif
+#endif
+
+/*
  * Boot Linux
  */
 #define CONFIG_CMDLINE_TAG

Hm, good ... so the SPI flash works now with no modifications ?

Matthias Fuchs

author

2012-01-18 18:49 UTC #4 lore raw

PATCH 3/3 mx28evk: add SPI support

Quoted 104 lines · Marek Vasut

Quoted 104 lines

This patch has been tested on a MX28EVK Rev. D with an installed SST25VF032B 32Mbit SPI flash.

Signed-off-by Matthias Fuchs <[email protected]>

---
 board/freescale/mx28evk/iomux.c |    8 +++++++
 include/configs/mx28evk.h       |   44

++++++++++++++++++++++++++++++++++++-- 2 files changed, 49 insertions(+), 3 deletions(-)

(quoted diff) +0 -0

b/board/freescale/mx28evk/iomux.c index 904e3f3..396761b 100644

board/freescale/mx28evk/iomux.c +8 -0

@@ -28,6 +28,7 @@
 #define	MUX_CONFIG_SSP0	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
 #define	MUX_CONFIG_ENET	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
 #define	MUX_CONFIG_EMI	(MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
+#define	MUX_CONFIG_SSP2	(MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_PULLUP)
 
 const iomux_cfg_t iomux_setup[] = {
 	/* DUART */

@@ -130,6 +131,13 @@ const iomux_cfg_t iomux_setup[] = {
 	MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
 	MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
 	MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
+
+	/* SPI2 (for SPI flash) */
+	MX28_PAD_SSP2_SCK__SSP2_SCK | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_MOSI__SSP2_CMD | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_MISO__SSP2_D0 | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_SS0__SSP2_D3 |
+		(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP),
 };
 
 void board_init_ll(void)

include/configs/mx28evk.h +38 -3

index 8f791aa..04967d7 100644
@@ -64,6 +64,8 @@
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_PING
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
 #define CONFIG_CMD_USB
 
 /*

@@ -127,9 +129,11 @@
  * MMC Driver
  */
 #define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_ENV_OFFSET	(256 * 1024)
-#define CONFIG_ENV_SIZE	(16 * 1024)
-#define CONFIG_SYS_MMC_ENV_DEV 0
+#ifdef CONFIG_ENV_IS_IN_MMC
+ #define CONFIG_ENV_OFFSET	(256 * 1024)
+ #define CONFIG_ENV_SIZE	(16 * 1024)
+ #define CONFIG_SYS_MMC_ENV_DEV 0
+#endif
 #define CONFIG_CMD_SAVEENV
 #ifdef	CONFIG_CMD_MMC
 #define CONFIG_MMC

@@ -170,6 +174,40 @@
 #endif
 
 /*
+ * SPI
+ */
+#ifdef CONFIG_CMD_SPI
+#define CONFIG_HARD_SPI
+#define CONFIG_MXS_SPI
+#define CONFIG_SPI_HALF_DUPLEX
+#define CONFIG_DEFAULT_SPI_BUS		2
+#define CONFIG_DEFAULT_SPI_MODE		SPI_MODE_0
+
+/* SPI Flash */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH
+/* this may vary and depends on the installed chip */
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+#define CONFIG_SF_DEFAULT_SPEED		24000000
+
+/* (redundant) environemnt in SPI flash */
+#undef CONFIG_ENV_IS_IN_SPI_FLASH
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_SIZE			0x1000		/* 4KB */
+#define CONFIG_ENV_OFFSET		0x40000		/* 256K */
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SECT_SIZE		0x1000
+#define CONFIG_ENV_SPI_CS		0
+#define CONFIG_ENV_SPI_BUS		2
+#define CONFIG_ENV_SPI_MAX_HZ		24000000
+#define CONFIG_ENV_SPI_MODE		SPI_MODE_0
+#endif
+#endif

Quoted 8 lines

include/configs/mx28evk.h line 213
Quoted 6 lines
include/configs/mx28evk.h +3 -0
+#endif
+
+/*
  * Boot Linux
  */
 #define CONFIG_CMDLINE_TAG
Hm, good ... so the SPI flash works now with no modifications ?

Of course not! The SPI driver needs to be fixed. Either by my previously posted patch or by god's hands :-)

Fabio asked for this patch in order to test my SPI driver fix. But I think this is independant from each other.

Matthias

Marek Vasut

2012-01-18 19:11 UTC #5 lore raw

PATCH 3/3 mx28evk: add SPI support

Quoted 137 lines · Marek Vasut

Quoted 129 lines

This patch has been tested on a MX28EVK Rev. D with an installed SST25VF032B 32Mbit SPI flash.

Signed-off-by Matthias Fuchs <[email protected]>

---

 board/freescale/mx28evk/iomux.c |    8 +++++++
 include/configs/mx28evk.h       |   44

++++++++++++++++++++++++++++++++++++-- 2 files changed, 49 insertions(+), 3 deletions(-)

(quoted diff) +0 -0

b/board/freescale/mx28evk/iomux.c index 904e3f3..396761b 100644

board/freescale/mx28evk/iomux.c +1 -0

@@ -28,6 +28,7 @@
 
 #define	MUX_CONFIG_SSP0	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
 #define	MUX_CONFIG_ENET	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
 #define	MUX_CONFIG_EMI	(MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
 
+#define	MUX_CONFIG_SSP2	(MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_PULLUP)

const iomux_cfg_t iomux_setup[] = {

board/freescale/mx28evk/iomux.c +7 -0

 	/* DUART */

@@ -130,6 +131,13 @@ const iomux_cfg_t iomux_setup[] = {
 
 	MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
 	MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
 	MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
 
+
+	/* SPI2 (for SPI flash) */
+	MX28_PAD_SSP2_SCK__SSP2_SCK | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_MOSI__SSP2_CMD | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_MISO__SSP2_D0 | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_SS0__SSP2_D3 |
+		(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP),

};

void board_init_ll(void)

include/configs/mx28evk.h +2 -0

index 8f791aa..04967d7 100644
@@ -64,6 +64,8 @@
 
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_PING
 
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI

#define CONFIG_CMD_USB

include/configs/mx28evk.h +5 -3

@@ -127,9 +129,11 @@
 
  * MMC Driver
  */
 
 #define CONFIG_ENV_IS_IN_MMC
 
-#define CONFIG_ENV_OFFSET	(256 * 1024)
-#define CONFIG_ENV_SIZE	(16 * 1024)
-#define CONFIG_SYS_MMC_ENV_DEV 0
+#ifdef CONFIG_ENV_IS_IN_MMC
+ #define CONFIG_ENV_OFFSET	(256 * 1024)
+ #define CONFIG_ENV_SIZE	(16 * 1024)
+ #define CONFIG_SYS_MMC_ENV_DEV 0
+#endif

#define CONFIG_CMD_SAVEENV
#ifdef CONFIG_CMD_MMC
#define CONFIG_MMC

include/configs/mx28evk.h +34 -0

@@ -170,6 +174,40 @@
 
 #endif
 
 /*
 
+ * SPI
+ */
+#ifdef CONFIG_CMD_SPI
+#define CONFIG_HARD_SPI
+#define CONFIG_MXS_SPI
+#define CONFIG_SPI_HALF_DUPLEX
+#define CONFIG_DEFAULT_SPI_BUS		2
+#define CONFIG_DEFAULT_SPI_MODE		SPI_MODE_0
+
+/* SPI Flash */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH
+/* this may vary and depends on the installed chip */
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+#define CONFIG_SF_DEFAULT_SPEED		24000000
+
+/* (redundant) environemnt in SPI flash */
+#undef CONFIG_ENV_IS_IN_SPI_FLASH
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_SIZE			0x1000		/* 4KB */
+#define CONFIG_ENV_OFFSET		0x40000		/* 256K */
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SECT_SIZE		0x1000
+#define CONFIG_ENV_SPI_CS		0
+#define CONFIG_ENV_SPI_BUS		2
+#define CONFIG_ENV_SPI_MAX_HZ		24000000
+#define CONFIG_ENV_SPI_MODE		SPI_MODE_0
+#endif
+#endif
+#endif
+
+/*

Quoted 6 lines

Quoted 4 lines
* Boot Linux
*/
#define CONFIG_CMDLINE_TAG
Hm, good ... so the SPI flash works now with no modifications ?

Quoted 7 lines

Of course not! The SPI driver needs to be fixed. Either by my previously posted patch or by god's hands :-)
Fabio asked for this patch in order to test my SPI driver fix. But I think this is independant from each other.
Matthias

Ok, I see ... sigh, can you please do such negotiations on the mailing list so people are informed about such?

Fabio Estevam

2012-01-23 21:34 UTC #6 lore raw

PATCH 3/3 mx28evk: add SPI support

In reply to Matthias Fuchs

Quoted 9 lines · Matthias Fuchs

This patch adds SPI support for the MX28EVK. Support for an optionally installed SPI flash is also added. An example configuration for redundant envrionment from SPI flash is also added but disabled by default.
This patch has been tested on a MX28EVK Rev. D with an installed SST25VF032B 32Mbit SPI flash.
Signed-off-by Matthias Fuchs <[email protected]>

Acked-by Fabio Estevam <[email protected]>

Stefano Babic

2012-02-07 08:14 UTC #7 lore raw

PATCH 3/3 mx28evk: add SPI support

In reply to Matthias Fuchs

Quoted 10 lines · Matthias Fuchs

This patch adds SPI support for the MX28EVK. Support for an optionally installed SPI flash is also added. An example configuration for redundant envrionment from SPI flash is also added but disabled by default.
This patch has been tested on a MX28EVK Rev. D with an installed SST25VF032B 32Mbit SPI flash.
Signed-off-by Matthias Fuchs <[email protected]>
---

Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

Signature · 5 lines

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

Fabio Estevam

2012-01-30 16:14 UTC #8 lore raw

PATCH 2/3 mx28evk: add USB support

In reply to Matthias Fuchs

Quoted 3 lines · Matthias Fuchs

This patch enables USB host support on the MX28EVK board.
Signed-off-by Matthias Fuchs <[email protected]>

Tested-by Fabio Estevam <[email protected]>

Thanks

Fabio Estevam

2012-01-30 16:14 UTC #9 lore raw

PATCH 2/3 mx28evk: add USB support

Quoted 6 lines · Fabio Estevam

Quoted 3 lines · Matthias Fuchs
This patch enables USB host support on the MX28EVK board.
Signed-off-by Matthias Fuchs <[email protected]>
Tested-by Fabio Estevam <[email protected]>

Adding Stefano.

Stefano Babic

2012-02-07 08:13 UTC #10 lore raw

PATCH 2/3 mx28evk: add USB support

In reply to Matthias Fuchs

Quoted 4 lines · Matthias Fuchs

This patch enables USB host support on the MX28EVK board.
Signed-off-by Matthias Fuchs <[email protected]>
---

Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

Signature · 5 lines

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

Marek Vasut

2012-01-18 16:07 UTC #11 lore raw

PATCH 1/3 mx28evk: add RTC support

In reply to Matthias Fuchs

Quoted 24 lines

This patch adds support for the MX28 internal RTC
and enables u-boot's date command.

Signed-off-by Matthias Fuchs <[email protected]>

---
 include/configs/mx28evk.h |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)

include/configs/mx28evk.h +1 -0

index bea46e7..8a752aa 100644
@@ -56,6 +56,7 @@
 #define CONFIG_CMD_FAT
 
 #define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_GPIO
 #define CONFIG_CMD_MII

@@ -150,6 +151,13 @@
 #endif
 
 /*

include/configs/mx28evk.h line 163

Quoted 10 lines

include/configs/mx28evk.h +7 -0

+ * RTC
+ */
+#ifdef	CONFIG_CMD_DATE
+#define	CONFIG_RTC_MXS
+#endif
+
+/*
  * Boot Linux
  */
 #define CONFIG_CMDLINE_TAG

Fabio, can you please test this and 2/3 ?
TIA
M

Fabio Estevam

2012-01-20 03:23 UTC #12 lore raw

PATCH 1/3 mx28evk: add RTC support

Quoted 1 line · Marek Vasut

Fabio, can you please test this and 2/3 ?

Yes, will test them soon.

Regards,

Fabio Estevam

Marek Vasut

2012-01-20 03:55 UTC #13 lore raw

PATCH 1/3 mx28evk: add RTC support

Quoted 8 lines · Marek Vasut

Quoted 1 line
Fabio, can you please test this and 2/3 ?
Yes, will test them soon.
Regards,
Fabio Estevam

Thanks a lot!

Fabio Estevam

2012-01-23 20:01 UTC #14 lore raw

PATCH 1/3 mx28evk: add RTC support

In reply to Matthias Fuchs

Quoted 4 lines · Matthias Fuchs

This patch adds support for the MX28 internal RTC
and enables u-boot's date command.
Signed-off-by Matthias Fuchs <[email protected]>

Tested-by Fabio Estevam <[email protected]>

Fabio Estevam

2012-02-06 12:51 UTC #15 lore raw

PATCH 1/3 mx28evk: add RTC support

Hi Stefano,

Quoted 7 lines · Fabio Estevam

Quoted 4 lines · Matthias Fuchs
This patch adds support for the MX28 internal RTC
and enables u-boot's date command.
Signed-off-by Matthias Fuchs <[email protected]>
Tested-by Fabio Estevam <[email protected]>

Any issues with this patch series?

If not, is it possible to apply them?

Thanks,

Fabio Estevam

Stefano Babic

2012-02-06 13:11 UTC #16 lore raw

PATCH 1/3 mx28evk: add RTC support

Quoted 7 lines · Fabio Estevam

Hi Stefano,
Quoted 4 lines · Fabio Estevam
Quoted 3 lines · Matthias Fuchs
This patch adds support for the MX28 internal RTC
and enables u-boot's date command.

Quoted 7 lines

Quoted 3 lines
Quoted 1 line
Signed-off-by Matthias Fuchs <[email protected]>
Tested-by Fabio Estevam <[email protected]>
Any issues with this patch series?
If not, is it possible to apply them?

No issue, I am going to apply them.

Best regards,
Stefano Babic

Signature · 5 lines

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

Stefano Babic

2012-02-07 08:12 UTC #17 lore raw

PATCH 1/3 mx28evk: add RTC support

In reply to Matthias Fuchs

Quoted 5 lines · Matthias Fuchs

This patch adds support for the MX28 internal RTC
and enables u-boot's date command.
Signed-off-by Matthias Fuchs <[email protected]>
---

Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

Signature · 5 lines

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================