libevas: Add new package.
PATCH 3/7 libevas: Add new package.
--- package/efl/Config.in | 1 + package/efl/libevas/Config.in | 199 ++++++++++++++++++++++++++++++++++++++++ package/efl/libevas/libevas.mk | 165 +++++++++++++++++++++++++++++++++ 3 files changed, 365 insertions(+), 0 deletions(-) create mode 100644 package/efl/libevas/Config.in create mode 100644 package/efl/libevas/libevas.mk
package/efl/Config.in +1 -0
@@ -10,6 +10,7 @@ if BR2_PACKAGE_EFL source "package/efl/libeina/Config.in" source "package/efl/libeet/Config.in" +source "package/efl/libevas/Config.in" endif # BR2_PACKAGE_EFL
package/efl/libevas/Config.in new file +199 -0
199 lines not on this page · raw message
package/efl/libevas/libevas.mk new file +165 -0
165 lines not on this page · raw message
Signature · 2 lines
1.7.1 -------------- next part --------------
PATCH 3/7 libevas: Add new package.
Quoted 1 line · On Wednesday 18 January 2012 12:15:31 Will Newton wrote:
Signed-off-by Will Newton <[email protected]>
[snip]
package/efl/libevas/Config.in line 98
Quoted 2 lines
package/efl/libevas/Config.in new file +2
-0+config BR2_PACKAGE_LIBEVAS_SDL + bool "libevas sdl backend"
I would expect a select BR2_PACKAGE_SDL here.
Quoted 4 lines
package/efl/libevas/Config.in new file +4
-0+ help + This is the sdl engine that uses sdl library + (http://www.libsdl.org). This library should work on many + operating system.
[snip]
Quoted 1 line
+comment "libevas code tunning"
tuning, not tunning
I would expect the following to be a choice rather than a set of bools.
Or can you sensibly compile libevas with no code?
package/efl/libevas/Config.in line 122
Quoted 3 lines
package/efl/libevas/Config.in new file +3
-0+ +config BR2_PACKAGE_LIBEVAS_C + bool "libevas c code"
This probably needs a 'default y'.
package/efl/libevas/Config.in line 130
Quoted 8 lines
package/efl/libevas/Config.in new file +8
-0+ help + This enabled the c code. you can actually build the code + without the c fallback code and only have the mmx routines + for example. + +config BR2_PACKAGE_LIBEVAS_MMX + bool "libevas mmx routines" + depends on BR2_i386 || BR2_x86_64
These dependencies could be a bit more accurate. You can find in 'man gcc'
which architectures support MMX. I guess something like this should work:
depends on (BR2_i386 && !BR2_x86_i386 && !BR2_x86_i486 && !BR2_x86_i586 && !BR2_x86_i686 && !BR2_x86_pentiumpro) || BR2_x86_64
package/efl/libevas/Config.in line 138
Quoted 8 lines
package/efl/libevas/Config.in new file +8
-0+ help + This enables the mmx optimised routines. this works for + pentium, pentium2, pentium3, pentium4, athlon and duron + processors. + +config BR2_PACKAGE_LIBEVAS_SSE + bool "libevas sse routines" + depends on BR2_i386 || BR2_x86_64
Same remark, but here you should find out of it is SSE, SSE2, SSE3, or
SSSE3 is required.
Quoted 4 lines
package/efl/libevas/Config.in new file +4
-0+ help + This enables sse optimizations availbale in he pentium3 and + 4 cpus (not athlon and duron or pentium 2 or pentium cpu's). +
[snip]
Quoted 7 lines
package/efl/libevas/libevas.mk new file +1
-0@@ -0,0 +1,165 @@ +#############################################################
package/efl/libevas/libevas.mk line 11
Quoted 10 lines
package/efl/libevas/libevas.mk new file +10
-0+# +# libevas +# +############################################################# + +LIBEVAS_VERSION = 1.1.0 +LIBEVAS_SOURCE = evas-$(LIBEVAS_VERSION).tar.bz2 +LIBEVAS_SITE = http://download.enlightenment.org/releases/ +LIBEVAS_INSTALL_STAGING = YES +LIBEVAS_INSTALL_TARGET = YES
_INSTALL_TARGET already defaults to YES.
package/efl/libevas/libevas.mk line 15
Quoted 3 lines
package/efl/libevas/libevas.mk new file +3
-0+LIBEVAS_DEPENDENCIES = host-pkg-config zlib libeina freetype + +LIBEVAS_CONF_OPT =
_CONF_OPT defaults to empty. It's OK to immediately assign using +=.
[snip]
package/efl/libevas/libevas.mk line 70
Quoted 4 lines
package/efl/libevas/libevas.mk new file +4
-0+ifeq ($(BR2_PACKAGE_LIBEVAS_GL_X11),y) + +LIBEVAS_CONF_OPT += --enable-gl-x11 +LIBEVAS_DEPENDENCIES += xserver_xorg-server
This doesn't correspond to the dependency in Config.in.
[snip]
Regards,
Arnout
Signature · 6 lines
Arnout Vandecappelle arnout at mind be Senior Embedded Software Architect +32-16-286540 Essensium/Mind http://www.mind.be G.Geenslaan 9, 3001 Leuven, Belgium BE 872 984 063 RPR Leuven LinkedIn profile: http://www.linkedin.com/in/arnoutvandecappelle GPG fingerprint: 7CB5 E4CC 6C2E EFD4 6E3D A754 F963 ECAB 2450 2F1F