VT1705 : Mic not working with power_save
Hi,
On the hardware described in attached alsa-info (VT1705), I have the following problem:
- mic doesn't work
- if, while recording, we switch "input source", mic works during the recording session.
Passing power_save=0 as a parameter to snd-hda-intel solves the problem.
It was reproduced on linus' master branch, tiwai's for-next branch, and 3.2 branch.
Regards,
Anisse
A message that is not in the archive (sent off-list or not yet received): [email protected]
(adding back list in Cc, it was lost)
Quoted 24 lines · On Mon, 13 Feb 2012 10:02:27 +0800, <[email protected]> wrote :
Quoted 15 lines
-----邮件原件-----
发件人: Anisse Astier [mailto:[email protected]]
发送时间: 2012年2月11日 1:56
收件人: [email protected]
抄送: Takashi Iwai; Lydia Wang
主题: VT1705 : Mic not working withpower_saveHi,
On the hardware described in attached alsa-info (VT1705), I have the following problem:
- mic doesn't work
- if, while recording, we switch "input source", mic works during the recording session.Quoted 8 lines
Passing power_save=0 as a parameter to snd-hda-intel solves the problem.
It was reproduced on linus' master branch, tiwai's for-next branch, and 3.2 branch.
Regards,
Anisse
Quoted 7 lines
Hi,
The log showed that your machine had two microphones, one is an internal mic, and the other is a rear mic. Which microphone did you use? The log showed currently used mic is the internal mic. The rear mic was not plugged in a jack.
Lydia
On this hardware, there's only an internal mic, and no physical jack to plug another input.
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Quoted 40 lines
-----邮件原件-----
发件人: Anisse Astier [mailto:[email protected]]
发送时间: 2012年2月13日 17:20
收件人: Lydia Wang
抄送: [email protected]; [email protected]
主题: Re: VT1705 : Mic not working withpower_save(adding back list in Cc, it was lost)
Quoted 22 lines · On Mon, 13 Feb 2012 10:02:27 +0800, <[email protected]> wrote :
Quoted 22 lines
-----邮件原件-----
发件人: Anisse Astier [mailto:[email protected]]
发送时间: 2012年2月11日 1:56
收件人: [email protected]
抄送: Takashi Iwai; Lydia Wang
主题: VT1705 : Mic not working withpower_saveHi,
On the hardware described in attached alsa-info (VT1705), I have the following problem:
- mic doesn't work
- if, while recording, we switch "input source", mic works during the recording session.Passing power_save=0 as a parameter to snd-hda-intel solves the problem.
It was reproduced on linus' master branch, tiwai's for-next branch, and 3.2 branch.
Regards,
Quoted 7 lines
Quoted 1 line
Anisse
Hi,
The log showed that your machine had two microphones, one is an internal mic, and the other is a rear mic. Which microphone did you use? The log showed currently used mic is the internal mic. The rear mic was not plugged in a
Quoted 6 lines
jack.
Quoted 2 lines
Lydia
On this hardware, there's only an internal mic, and no physical jack to plug another input.
So " mic doesn't work " means recording fail or playback as aa-path fail? And could you mail me log file when power_saver=1? Thanks.
Lydia
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Quoted 19 lines · On Mon, 13 Feb 2012 17:30:57 +0800, <[email protected]> wrote :
Quoted 19 lines
-----邮件原件-----
发件人: Anisse Astier [mailto:[email protected]]
发送时间: 2012年2月13日 17:20
收件人: Lydia Wang
抄送: [email protected]; [email protected]
主题: Re: VT1705 : Mic not working withpower_save(adding back list in Cc, it was lost)
Quoted 6 lines · On Mon, 13 Feb 2012 10:02:27 +0800, <[email protected]> wrote :
Hi,
The log showed that your machine had two microphones, one is an internal mic, and the other is a rear mic. Which microphone did you use? The log showed currently used mic is the internal mic. The rear mic was not plugged in a
jack.
Quoted 1 line
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
Lydia
On this hardware, there's only an internal mic, and no physical jack to plug another input.
So " mic doesn't work " means recording fail or playback as aa-path fail? And could you mail me log file when power_saver=1? Thanks.
Mic doesn't work means recording fails. Except if, during the recording, I use the "Input Source" control to change to another input, *and then back* to "Internal Mic".
If I start another recording, it will still be silent unless I repeat the previous sequence.
I don't use mic directly for playback (with hardware a-a path)
Please find the full log and alsa-info in attachment with power_save=1.
Anisse
At Mon, 13 Feb 2012 11:06:53 +0100,
Quoted 36 lines · Anisse Astier
Quoted 19 lines · On Mon, 13 Feb 2012 17:30:57 +0800, <[email protected]> wrote :
Quoted 19 lines
-----邮件原件-----
发件人: Anisse Astier [mailto:[email protected]]
发送时间: 2012年2月13日 17:20
收件人: Lydia Wang
抄送: [email protected]; [email protected]
主题: Re: VT1705 : Mic not working withpower_save(adding back list in Cc, it was lost)
Quoted 6 lines · On Mon, 13 Feb 2012 10:02:27 +0800, <[email protected]> wrote :
Hi,
The log showed that your machine had two microphones, one is an internal mic, and the other is a rear mic. Which microphone did you use? The log showed currently used mic is the internal mic. The rear mic was not plugged in a
jack.
Quoted 1 line
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
Lydia
On this hardware, there's only an internal mic, and no physical jack to plug another input.
So " mic doesn't work " means recording fail or playback as aa-path fail? And could you mail me log file when power_saver=1? Thanks.
Mic doesn't work means recording fails. Except if, during the recording, I use the "Input Source" control to change to another input, *and then back* to "Internal Mic".
If I start another recording, it will still be silent unless I repeat the previous sequence.
Quoted 3 lines
I don't use mic directly for playback (with hardware a-a path)
Please find the full log and alsa-info in attachment with power_save=1.
Thanks.
I found the culprit. It's because VT1705 has a secondary ADC that has no input-mux while the primary ADC has one. At the initialization, the secondary ADC overwrites the MUX value always to zero because of it.
The patch below should fix the problem. Let me know if it works (at best give your tested-by line).
thanks,
Takashi
---
sound/pci/hda/patch_via.c +2 -0
@@ -666,6 +666,8 @@ static void via_auto_init_analog_input(struct hda_codec *codec)/* init input-src */ for (i =0 ; i < spec->num_adc_nids; i++) {int adc_idx = spec->inputs[spec->cur_mux[i]].adc_idx; +if (i >0 && !spec->mux_nids[i]) +break ;if (spec->mux_nids[adc_idx]) {int mux_idx = spec->inputs[spec->cur_mux[i]].mux_idx; snd_hda_codec_write(codec, spec->mux_nids[adc_idx], 0,
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Anisse Astier
Tested-byQuoted 63 lines · Takashi Iwai
At Mon, 13 Feb 2012 11:06:53 +0100,
Quoted 36 lines · Anisse Astier
Quoted 19 lines · On Mon, 13 Feb 2012 17:30:57 +0800, <[email protected]> wrote :
Quoted 19 lines
-----邮件原件-----
发件人: Anisse Astier [mailto:[email protected]]
发送时间: 2012年2月13日 17:20
收件人: Lydia Wang
抄送: [email protected]; [email protected]
主题: Re: VT1705 : Mic not working withpower_save(adding back list in Cc, it was lost)
Quoted 6 lines · On Mon, 13 Feb 2012 10:02:27 +0800, <[email protected]> wrote :
Hi,
The log showed that your machine had two microphones, one is an internal mic, and the other is a rear mic. Which microphone did you use? The log showed currently used mic is the internal mic. The rear mic was not plugged in a
jack.
Quoted 1 line
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
Lydia
On this hardware, there's only an internal mic, and no physical jack to plug another input.
So " mic doesn't work " means recording fail or playback as aa-path fail? And could you mail me log file when power_saver=1? Thanks.
Mic doesn't work means recording fails. Except if, during the recording, I use the "Input Source" control to change to another input, *and then back* to "Internal Mic".
If I start another recording, it will still be silent unless I repeat the previous sequence.Quoted 3 lines
I don't use mic directly for playback (with hardware a-a path)
Please find the full log and alsa-info in attachment with power_save=1.
Thanks.
I found the culprit. It's because VT1705 has a secondary ADC that has no input-mux while the primary ADC has one. At the initialization, the secondary ADC overwrites the MUX value always to zero because of it.
The patch below should fix the problem. Let me know if it works (at best give your tested-by line).
thanks,
Takashi
---
sound/pci/hda/patch_via.c +0
-0
sound/pci/hda/patch_via.c static void via_auto_init_analog_input(struct hda_codec *codec) · line 673
Quoted 8 lines
sound/pci/hda/patch_via.c +2
-0@@ -666,6 +666,8 @@ static void via_auto_init_analog_input(struct hda_codec *codec)/* init input-src */ for (i =0 ; i < spec->num_adc_nids; i++) {int adc_idx = spec->inputs[spec->cur_mux[i]].adc_idx; +if (i >0 && !spec->mux_nids[i]) +break ;if (spec->mux_nids[adc_idx]) {int mux_idx = spec->inputs[spec->cur_mux[i]].mux_idx; snd_hda_codec_write(codec, spec->mux_nids[adc_idx], 0,
It works!
I wouldn't mind a Cc: stable too.
Thanks,
Anisse
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
At Mon, 13 Feb 2012 14:59:16 +0100,
Quoted 76 lines · Anisse Astier
Quoted 63 lines · Takashi Iwai
At Mon, 13 Feb 2012 11:06:53 +0100,
Quoted 36 lines · Anisse Astier
Quoted 19 lines · On Mon, 13 Feb 2012 17:30:57 +0800, <[email protected]> wrote :
Quoted 19 lines
-----邮件原件-----
发件人: Anisse Astier [mailto:[email protected]]
发送时间: 2012年2月13日 17:20
收件人: Lydia Wang
抄送: [email protected]; [email protected]
主题: Re: VT1705 : Mic not working withpower_save(adding back list in Cc, it was lost)
Quoted 6 lines · On Mon, 13 Feb 2012 10:02:27 +0800, <[email protected]> wrote :
Hi,
The log showed that your machine had two microphones, one is an internal mic, and the other is a rear mic. Which microphone did you use? The log showed currently used mic is the internal mic. The rear mic was not plugged in a
jack.
Quoted 1 line
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
Lydia
On this hardware, there's only an internal mic, and no physical jack to plug another input.
So " mic doesn't work " means recording fail or playback as aa-path fail? And could you mail me log file when power_saver=1? Thanks.
Mic doesn't work means recording fails. Except if, during the recording, I use the "Input Source" control to change to another input, *and then back* to "Internal Mic".
If I start another recording, it will still be silent unless I repeat the previous sequence.Quoted 3 lines
I don't use mic directly for playback (with hardware a-a path)
Please find the full log and alsa-info in attachment with power_save=1.
Thanks.
I found the culprit. It's because VT1705 has a secondary ADC that has no input-mux while the primary ADC has one. At the initialization, the secondary ADC overwrites the MUX value always to zero because of it.
The patch below should fix the problem. Let me know if it works (at best give your tested-by line).
thanks,
Takashi
---
sound/pci/hda/patch_via.c +0
-0sound/pci/hda/patch_via.c static void via_auto_init_analog_input(struct hda_codec *codec) · line 673
Quoted 8 lines
sound/pci/hda/patch_via.c +2
-0@@ -666,6 +666,8 @@ static void via_auto_init_analog_input(struct hda_codec *codec)/* init input-src */ for (i =0 ; i < spec->num_adc_nids; i++) {int adc_idx = spec->inputs[spec->cur_mux[i]].adc_idx; +if (i >0 && !spec->mux_nids[i]) +break ;if (spec->mux_nids[adc_idx]) {int mux_idx = spec->inputs[spec->cur_mux[i]].mux_idx; snd_hda_codec_write(codec, spec->mux_nids[adc_idx], 0,It works!
Quoted 3 lines
Tested-by Anisse Astier <[email protected]>I wouldn't mind a Cc: stable too.
Yes, definitely. I applied the patch now to the sound git tree.
thanks,
Takashi
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel