Microblaze: build kernel with device tree
PATCH 1/2 Microblaze: build kernel with device tree
This patch adds the options needed to build the SimpleImage containing the device tree structure needed for the Microblaze architecture.
Handling Device Tree and SimpleImage will be handled in a general way in the future.
I provide this patch to be able to build the system in the meantime.
--- linux/Config.in | 8 ++++++++ linux/linux.mk | 16 ++++++++++++++++ 2 files changed, 24 insertions(+), 0 deletions(-)
linux/Config.in +8 -0
@@ -120,6 +120,14 @@ config BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE help Path to the kernel configuration file +config BR2_LINUX_KERNEL_DTS_FILE + string "Device Tree dts file location" + depends on BR2_microblaze + help + Path from where the dts file has to be copied + The final "custom target" name depends on the + dts file name: + <name>.dts --> simpleImage.<name> # # Binary format #
linux/linux.mk +16 -0
@@ -117,6 +117,18 @@ endef LINUX_POST_PATCH_HOOKS += LINUX_APPLY_PATCHES +ifeq ($(KERNEL_ARCH),microblaze) +# on microblaze, we always want mkimage +LINUX_DEPENDENCIES+=host-uboot-tools + +define LINUX_COPY_DTS + if test -f "$(BR2_LINUX_KERNEL_DTS_FILE)" ; then \ + cp $(BR2_LINUX_KERNEL_DTS_FILE) $(@D)/arch/microblaze/boot/dts ; \ + else \ + echo "Cannot copy dts file!" ; \ + fi +endef +endif ifeq ($(BR2_LINUX_KERNEL_USE_DEFCONFIG),y) KERNEL_SOURCE_CONFIG = $(KERNEL_ARCH_PATH)/configs/$(call qstrip,$(BR2_LINUX_KERNEL_DEFCONFIG))_defconfig
@@ -131,6 +143,8 @@ define LINUX_CONFIGURE_CMDS $(if $(BR2_ARM_EABI), $(call KCONFIG_ENABLE_OPT,CONFIG_AEABI,$(@D)/.config), $(call KCONFIG_DISABLE_OPT,CONFIG_AEABI,$(@D)/.config)) + $(if $(BR2_microblaze), + $(call LINUX_COPY_DTS)) # As the kernel gets compiled before root filesystems are # built, we create a fake cpio file. It'll be # replaced later by the real cpio archive, and the kernel will be
@@ -215,6 +229,8 @@ $(LINUX_DIR)/.stamp_initramfs_rebuilt: $(LINUX_DIR)/.stamp_target_installed $(LI $(TARGET_MAKE_ENV) $(MAKE) $(LINUX_MAKE_FLAGS) -C $(@D) $(LINUX_IMAGE_NAME) # Copy the kernel image to its final destination cp $(LINUX_IMAGE_PATH) $(BINARIES_DIR) + # If there is a .ub file copy it to the final destination + test -f $(LINUX_IMAGE_PATH).ub && cp $(LINUX_IMAGE_PATH).ub $(BINARIES_DIR) $(Q)touch $@ # The initramfs building code must make sure this target gets called
Signature · 1 line
1.7.0.4
PATCH 2/2 Microblaze: added defconfig for Avnet S6LX9 Microboard
The Avnet S6LX9 Microboard is a small USB-Stick sized module containing a Spartan6 FPGA capable of running the Microblaze softcore processor together with RAM and FLASH memory.
This board support pachage assumes that the Microblaze Bitfile available from the Avnet website is programmed into the FPGA.
--- board/avnet/s6lx9_microboard/lx9_mmu.dts | 247 ++++++++++++++++++++++++ board/avnet/s6lx9_microboard/lx9_mmu_defconfig | 68 +++++++ board/avnet/s6lx9_microboard/readme.txt | 70 +++++++ configs/s6lx9_microboard_defconfig | 17 ++ 4 files changed, 402 insertions(+), 0 deletions(-) create mode 100644 board/avnet/s6lx9_microboard/lx9_mmu.dts create mode 100644 board/avnet/s6lx9_microboard/lx9_mmu_defconfig create mode 100644 board/avnet/s6lx9_microboard/readme.txt create mode 100644 configs/s6lx9_microboard_defconfig
board/avnet/s6lx9_microboard/lx9_mmu.dts new file +247 -0
@@ -0,0 +1,247 @@ +/* + * Device Tree Generator version: 1.3 + * + * (C) Copyright 2007-2008 Xilinx, Inc. + * (C) Copyright 2007-2009 Michal Simek + * + * Michal SIMEK <[email protected]> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + * CAUTION: This file is automatically generated by libgen. + * Version: Xilinx EDK 13.2 EDK_O.61xd + * + * XPS project directory: device-tree_bsp_230-orig + */ + +/dts-v1/; +/ { + #address-cells = <1>; + #size-cells = <1>; + compatible = "xlnx,microblaze"; + model = "testing"; + MCB3_LPDDR: memory at 80000000 { + device_type = "memory"; + reg = < 0x80000000 0x4000000 >; + } ; + aliases { + ethernet0 = &Ethernet_MAC; + serial0 = &USB_Uart; + } ; + chosen { + bootargs = "console=ttyUL0"; + linux,stdout-path = "/axi at 0/serial at 40600000"; + } ; + cpus { + #address-cells = <1>; + #cpus = <0x1>; + #size-cells = <0>; + microblaze_0: cpu at 0 { + clock-frequency = <66666667>; + compatible = "xlnx,microblaze-8.20.a"; + d-cache-baseaddr = <0x80000000>; + d-cache-highaddr = <0x83ffffff>; + d-cache-line-size = <0x10>; + d-cache-size = <0x2000>; + device_type = "cpu"; + i-cache-baseaddr = <0x80000000>; + i-cache-highaddr = <0x83ffffff>; + i-cache-line-size = <0x10>; + i-cache-size = <0x2000>; + model = "microblaze,8.20.a"; + reg = <0>; + timebase-frequency = <66666667>; + xlnx,addr-tag-bits = <0xd>; + xlnx,allow-dcache-wr = <0x1>; + xlnx,allow-icache-wr = <0x1>; + xlnx,area-optimized = <0x0>; + xlnx,avoid-primitives = <0x0>; + xlnx,branch-target-cache-size = <0x0>; + xlnx,cache-byte-size = <0x2000>; + xlnx,d-axi = <0x1>; + xlnx,d-lmb = <0x1>; + xlnx,d-plb = <0x0>; + xlnx,data-size = <0x20>; + xlnx,dcache-addr-tag = <0xd>; + xlnx,dcache-always-used = <0x1>; + xlnx,dcache-byte-size = <0x2000>; + xlnx,dcache-data-width = <0x0>; + xlnx,dcache-force-tag-lutram = <0x0>; + xlnx,dcache-interface = <0x0>; + xlnx,dcache-line-len = <0x4>; + xlnx,dcache-use-fsl = <0x0>; + xlnx,dcache-use-writeback = <0x0>; + xlnx,dcache-victims = <0x0>; + xlnx,debug-enabled = <0x1>; + xlnx,div-zero-exception = <0x0>; + xlnx,dynamic-bus-sizing = <0x1>; + xlnx,ecc-use-ce-exception = <0x0>; + xlnx,edge-is-positive = <0x1>; + xlnx,endianness = <0x1>; + xlnx,family = "spartan6"; + xlnx,fault-tolerant = <0x0>; + xlnx,fpu-exception = <0x0>; + xlnx,freq = <0x3f940ab>; + xlnx,fsl-data-size = <0x20>; + xlnx,fsl-exception = <0x0>; + xlnx,fsl-links = <0x0>; + xlnx,i-axi = <0x0>; + xlnx,i-lmb = <0x1>; + xlnx,i-plb = <0x0>; + xlnx,icache-always-used = <0x1>; + xlnx,icache-data-width = <0x0>; + xlnx,icache-force-tag-lutram = <0x0>; + xlnx,icache-interface = <0x0>; + xlnx,icache-line-len = <0x4>; + xlnx,icache-streams = <0x0>; + xlnx,icache-use-fsl = <0x0>; + xlnx,icache-victims = <0x0>; + xlnx,ill-opcode-exception = <0x0>; + xlnx,instance = "microblaze_0"; + xlnx,interconnect = <0x2>; + xlnx,interconnect-m-axi-dc-aw-register = <0x0>; + xlnx,interconnect-m-axi-dc-read-issuing = <0x2>; + xlnx,interconnect-m-axi-dc-w-register = <0x0>; + xlnx,interconnect-m-axi-dc-write-issuing = <0x20>; + xlnx,interconnect-m-axi-dp-read-issuing = <0x1>; + xlnx,interconnect-m-axi-dp-write-issuing = <0x1>; + xlnx,interconnect-m-axi-ic-read-issuing = <0x2>; + xlnx,interconnect-m-axi-ip-read-issuing = <0x1>; + xlnx,interrupt-is-edge = <0x0>; + xlnx,lockstep-slave = <0x0>; + xlnx,mmu-dtlb-size = <0x1>; + xlnx,mmu-itlb-size = <0x1>; + xlnx,mmu-privileged-instr = <0x0>; + xlnx,mmu-tlb-access = <0x3>; + xlnx,mmu-zones = <0x2>; + xlnx,number-of-pc-brk = <0x1>; + xlnx,number-of-rd-addr-brk = <0x0>; + xlnx,number-of-wr-addr-brk = <0x0>; + xlnx,opcode-0x0-illegal = <0x0>; + xlnx,optimization = <0x0>; + xlnx,pvr = <0x0>; + xlnx,pvr-user1 = <0x0>; + xlnx,pvr-user2 = <0x0>; + xlnx,reset-msr = <0x0>; + xlnx,sco = <0x0>; + xlnx,stream-interconnect = <0x0>; + xlnx,unaligned-exceptions = <0x0>; + xlnx,use-barrel = <0x1>; + xlnx,use-branch-target-cache = <0x0>; + xlnx,use-dcache = <0x1>; + xlnx,use-div = <0x0>; + xlnx,use-ext-brk = <0x1>; + xlnx,use-ext-nm-brk = <0x1>; + xlnx,use-extended-fsl-instr = <0x0>; + xlnx,use-fpu = <0x0>; + xlnx,use-hw-mul = <0x1>; + xlnx,use-icache = <0x1>; + xlnx,use-interrupt = <0x1>; + xlnx,use-mmu = <0x3>; + xlnx,use-msr-instr = <0x1>; + xlnx,use-pcmp-instr = <0x0>; + xlnx,use-stack-protection = <0x0>; + } ; + } ; + axi4lite_0: axi at 0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "xlnx,axi-interconnect-1.03.a", "simple-bus"; + ranges ; + Ethernet_MAC: ethernet at 40e00000 { + compatible = "xlnx,axi-ethernetlite-1.00.a", "xlnx,xps-ethernetlite-1.00.a"; + device_type = "network"; + interrupt-parent = <µblaze_0_intc>; + interrupts = < 2 0 >; + local-mac-address = [ 00 0a 35 aa de 00 ]; +// phy-handle = <&phy0>; + reg = < 0x40e00000 0x10000 >; + xlnx,duplex = <0x1>; + xlnx,family = "spartan6"; + xlnx,include-global-buffers = <0x0>; + xlnx,include-internal-loopback = <0x0>; + xlnx,include-mdio = <0x1>; + xlnx,include-phy-constraints = <0x1>; + xlnx,interconnect-s-axi-read-acceptance = <0x1>; + xlnx,interconnect-s-axi-write-acceptance = <0x1>; + xlnx,rx-ping-pong = <0x0>; + xlnx,s-axi-aclk-period-ps = <0x3a98>; + xlnx,s-axi-id-width = <0x1>; + xlnx,s-axi-supports-narrow-burst = <0x0>; + xlnx,tx-ping-pong = <0x0>; +/* + mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: phy at 7 { + compatible = "marvell,88e1111"; + device_type = "ethernet-phy"; + reg = <7>; + } ; + } ; +*/ + } ; + SPI_FLASH: spi at 40a00000 { + compatible = "xlnx,axi-spi-1.01.a", "xlnx,xps-spi-2.00.a"; + interrupt-parent = <µblaze_0_intc>; + interrupts = < 1 2 >; + reg = < 0x40a00000 0x10000 >; + xlnx,family = "spartan6"; + xlnx,fifo-exist = <0x1>; + xlnx,num-ss-bits = <0x1>; + xlnx,num-transfer-bits = <0x8>; + xlnx,sck-ratio = <0x4>; + } ; + USB_Uart: serial at 40600000 { + clock-frequency = <66666667>; + compatible = "xlnx,axi-uartlite-1.02.a", "xlnx,xps-uartlite-1.00.a"; + current-speed = <115200>; + device_type = "serial"; + interrupt-parent = <µblaze_0_intc>; + interrupts = < 3 0 >; + port-number = <0>; + reg = < 0x40600000 0x10000 >; + xlnx,baudrate = <0x1c200>; + xlnx,data-bits = <0x8>; + xlnx,family = "spartan6"; + xlnx,odd-parity = <0x1>; + xlnx,s-axi-aclk-freq-hz = <0x3f940ab>; + xlnx,use-parity = <0x0>; + } ; + microblaze_0_intc: interrupt-controller at 41200000 { + #interrupt-cells = <0x2>; + compatible = "xlnx,axi-intc-1.01.a", "xlnx,xps-intc-1.00.a"; + interrupt-controller ; + reg = < 0x41200000 0x10000 >; + xlnx,kind-of-intr = <0xc>; + xlnx,num-intr-inputs = <0x4>; + } ; + system_timer: timer at 41c00000 { + clock-frequency = <66666667>; + compatible = "xlnx,axi-timer-1.02.a", "xlnx,xps-timer-1.00.a"; + interrupt-parent = <µblaze_0_intc>; + interrupts = < 0 2 >; + reg = < 0x41c00000 0x10000 >; + xlnx,count-width = <0x20>; + xlnx,family = "spartan6"; + xlnx,gen0-assert = <0x1>; + xlnx,gen1-assert = <0x1>; + xlnx,one-timer-only = <0x0>; + xlnx,trig0-assert = <0x1>; + xlnx,trig1-assert = <0x1>; + } ; + } ; +} ;
board/avnet/s6lx9_microboard/lx9_mmu_defconfig new file +68 -0
68 lines not on this page · raw message
board/avnet/s6lx9_microboard/readme.txt new file +70 -0
70 lines not on this page · raw message
configs/s6lx9_microboard_defconfig new file +17 -0
@@ -0,0 +1,17 @@ +BR2_microblaze=y +BR2_microblazeel=y +BR2_TOOLCHAIN_EXTERNAL=y +BR2_TOOLCHAIN_EXTERNAL_XILINX_MICROBLAZEEL_V2=y +BR2_TOOLCHAIN_EXTERNAL_DOWNLOAD=y +BR2_TOOLCHAIN_EXTERNAL_CUSTOM_PREFIX="microblazeel-unknown-linux-gnu" +BR2_TOOLCHAIN_EXTERNAL_CUSTOM_GLIBC=y +BR2_TOOLCHAIN_EXTERNAL_CXX=y +BR2_TARGET_GENERIC_GETTY_PORT="ttyUL0" +# BR2_TARGET_ROOTFS_TAR is not set +BR2_TARGET_ROOTFS_INITRAMFS=y +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y +BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/avnet/s6lx9_microboard/lx9_mmu_defconfig" +BR2_LINUX_KERNEL_DTS_FILE="board/avnet/s6lx9_microboard/lx9_mmu.dts" +BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y +BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="simpleImage.lx9_mmu"
Signature · 1 line
1.7.0.4
PATCH 1/1 Microblaze: added defconfig for Avnet S6LX9 Microboard
From: Stephan Hoffmann <[email protected]>
The Avnet S6LX9 Microboard is a small USB-Stick sized module containing a Spartan6 FPGA capable of running the Microblaze softcore processor together with RAM and FLASH memory.
This board support package assumes that the Microblaze Bitfile available from the Avnet website is programmed into the FPGA.
---
I removed a whitespace in board/avnet/s6lx9_microboard/readme.txt (don't like them) and changed pachage -> package in the commit message. Everything else is the same.
board/avnet/s6lx9_microboard/lx9_mmu.dts | 247 ++++++++++++++++++++++++ board/avnet/s6lx9_microboard/lx9_mmu_defconfig | 68 +++++++ board/avnet/s6lx9_microboard/readme.txt | 70 +++++++ configs/s6lx9_microboard_defconfig | 17 ++ 4 files changed, 402 insertions(+), 0 deletions(-) create mode 100644 board/avnet/s6lx9_microboard/lx9_mmu.dts create mode 100644 board/avnet/s6lx9_microboard/lx9_mmu_defconfig create mode 100644 board/avnet/s6lx9_microboard/readme.txt create mode 100644 configs/s6lx9_microboard_defconfig
board/avnet/s6lx9_microboard/lx9_mmu.dts new file +247 -0
@@ -0,0 +1,247 @@ +/* + * Device Tree Generator version: 1.3 + * + * (C) Copyright 2007-2008 Xilinx, Inc. + * (C) Copyright 2007-2009 Michal Simek + * + * Michal SIMEK <[email protected]> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + * CAUTION: This file is automatically generated by libgen. + * Version: Xilinx EDK 13.2 EDK_O.61xd + * + * XPS project directory: device-tree_bsp_230-orig + */ + +/dts-v1/; +/ { + #address-cells = <1>; + #size-cells = <1>; + compatible = "xlnx,microblaze"; + model = "testing"; + MCB3_LPDDR: memory at 80000000 { + device_type = "memory"; + reg = < 0x80000000 0x4000000 >; + } ; + aliases { + ethernet0 = &Ethernet_MAC; + serial0 = &USB_Uart; + } ; + chosen { + bootargs = "console=ttyUL0"; + linux,stdout-path = "/axi at 0/serial at 40600000"; + } ; + cpus { + #address-cells = <1>; + #cpus = <0x1>; + #size-cells = <0>; + microblaze_0: cpu at 0 { + clock-frequency = <66666667>; + compatible = "xlnx,microblaze-8.20.a"; + d-cache-baseaddr = <0x80000000>; + d-cache-highaddr = <0x83ffffff>; + d-cache-line-size = <0x10>; + d-cache-size = <0x2000>; + device_type = "cpu"; + i-cache-baseaddr = <0x80000000>; + i-cache-highaddr = <0x83ffffff>; + i-cache-line-size = <0x10>; + i-cache-size = <0x2000>; + model = "microblaze,8.20.a"; + reg = <0>; + timebase-frequency = <66666667>; + xlnx,addr-tag-bits = <0xd>; + xlnx,allow-dcache-wr = <0x1>; + xlnx,allow-icache-wr = <0x1>; + xlnx,area-optimized = <0x0>; + xlnx,avoid-primitives = <0x0>; + xlnx,branch-target-cache-size = <0x0>; + xlnx,cache-byte-size = <0x2000>; + xlnx,d-axi = <0x1>; + xlnx,d-lmb = <0x1>; + xlnx,d-plb = <0x0>; + xlnx,data-size = <0x20>; + xlnx,dcache-addr-tag = <0xd>; + xlnx,dcache-always-used = <0x1>; + xlnx,dcache-byte-size = <0x2000>; + xlnx,dcache-data-width = <0x0>; + xlnx,dcache-force-tag-lutram = <0x0>; + xlnx,dcache-interface = <0x0>; + xlnx,dcache-line-len = <0x4>; + xlnx,dcache-use-fsl = <0x0>; + xlnx,dcache-use-writeback = <0x0>; + xlnx,dcache-victims = <0x0>; + xlnx,debug-enabled = <0x1>; + xlnx,div-zero-exception = <0x0>; + xlnx,dynamic-bus-sizing = <0x1>; + xlnx,ecc-use-ce-exception = <0x0>; + xlnx,edge-is-positive = <0x1>; + xlnx,endianness = <0x1>; + xlnx,family = "spartan6"; + xlnx,fault-tolerant = <0x0>; + xlnx,fpu-exception = <0x0>; + xlnx,freq = <0x3f940ab>; + xlnx,fsl-data-size = <0x20>; + xlnx,fsl-exception = <0x0>; + xlnx,fsl-links = <0x0>; + xlnx,i-axi = <0x0>; + xlnx,i-lmb = <0x1>; + xlnx,i-plb = <0x0>; + xlnx,icache-always-used = <0x1>; + xlnx,icache-data-width = <0x0>; + xlnx,icache-force-tag-lutram = <0x0>; + xlnx,icache-interface = <0x0>; + xlnx,icache-line-len = <0x4>; + xlnx,icache-streams = <0x0>; + xlnx,icache-use-fsl = <0x0>; + xlnx,icache-victims = <0x0>; + xlnx,ill-opcode-exception = <0x0>; + xlnx,instance = "microblaze_0"; + xlnx,interconnect = <0x2>; + xlnx,interconnect-m-axi-dc-aw-register = <0x0>; + xlnx,interconnect-m-axi-dc-read-issuing = <0x2>; + xlnx,interconnect-m-axi-dc-w-register = <0x0>; + xlnx,interconnect-m-axi-dc-write-issuing = <0x20>; + xlnx,interconnect-m-axi-dp-read-issuing = <0x1>; + xlnx,interconnect-m-axi-dp-write-issuing = <0x1>; + xlnx,interconnect-m-axi-ic-read-issuing = <0x2>; + xlnx,interconnect-m-axi-ip-read-issuing = <0x1>; + xlnx,interrupt-is-edge = <0x0>; + xlnx,lockstep-slave = <0x0>; + xlnx,mmu-dtlb-size = <0x1>; + xlnx,mmu-itlb-size = <0x1>; + xlnx,mmu-privileged-instr = <0x0>; + xlnx,mmu-tlb-access = <0x3>; + xlnx,mmu-zones = <0x2>; + xlnx,number-of-pc-brk = <0x1>; + xlnx,number-of-rd-addr-brk = <0x0>; + xlnx,number-of-wr-addr-brk = <0x0>; + xlnx,opcode-0x0-illegal = <0x0>; + xlnx,optimization = <0x0>; + xlnx,pvr = <0x0>; + xlnx,pvr-user1 = <0x0>; + xlnx,pvr-user2 = <0x0>; + xlnx,reset-msr = <0x0>; + xlnx,sco = <0x0>; + xlnx,stream-interconnect = <0x0>; + xlnx,unaligned-exceptions = <0x0>; + xlnx,use-barrel = <0x1>; + xlnx,use-branch-target-cache = <0x0>; + xlnx,use-dcache = <0x1>; + xlnx,use-div = <0x0>; + xlnx,use-ext-brk = <0x1>; + xlnx,use-ext-nm-brk = <0x1>; + xlnx,use-extended-fsl-instr = <0x0>; + xlnx,use-fpu = <0x0>; + xlnx,use-hw-mul = <0x1>; + xlnx,use-icache = <0x1>; + xlnx,use-interrupt = <0x1>; + xlnx,use-mmu = <0x3>; + xlnx,use-msr-instr = <0x1>; + xlnx,use-pcmp-instr = <0x0>; + xlnx,use-stack-protection = <0x0>; + } ; + } ; + axi4lite_0: axi at 0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "xlnx,axi-interconnect-1.03.a", "simple-bus"; + ranges ; + Ethernet_MAC: ethernet at 40e00000 { + compatible = "xlnx,axi-ethernetlite-1.00.a", "xlnx,xps-ethernetlite-1.00.a"; + device_type = "network"; + interrupt-parent = <µblaze_0_intc>; + interrupts = < 2 0 >; + local-mac-address = [ 00 0a 35 aa de 00 ]; +// phy-handle = <&phy0>; + reg = < 0x40e00000 0x10000 >; + xlnx,duplex = <0x1>; + xlnx,family = "spartan6"; + xlnx,include-global-buffers = <0x0>; + xlnx,include-internal-loopback = <0x0>; + xlnx,include-mdio = <0x1>; + xlnx,include-phy-constraints = <0x1>; + xlnx,interconnect-s-axi-read-acceptance = <0x1>; + xlnx,interconnect-s-axi-write-acceptance = <0x1>; + xlnx,rx-ping-pong = <0x0>; + xlnx,s-axi-aclk-period-ps = <0x3a98>; + xlnx,s-axi-id-width = <0x1>; + xlnx,s-axi-supports-narrow-burst = <0x0>; + xlnx,tx-ping-pong = <0x0>; +/* + mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: phy at 7 { + compatible = "marvell,88e1111"; + device_type = "ethernet-phy"; + reg = <7>; + } ; + } ; +*/ + } ; + SPI_FLASH: spi at 40a00000 { + compatible = "xlnx,axi-spi-1.01.a", "xlnx,xps-spi-2.00.a"; + interrupt-parent = <µblaze_0_intc>; + interrupts = < 1 2 >; + reg = < 0x40a00000 0x10000 >; + xlnx,family = "spartan6"; + xlnx,fifo-exist = <0x1>; + xlnx,num-ss-bits = <0x1>; + xlnx,num-transfer-bits = <0x8>; + xlnx,sck-ratio = <0x4>; + } ; + USB_Uart: serial at 40600000 { + clock-frequency = <66666667>; + compatible = "xlnx,axi-uartlite-1.02.a", "xlnx,xps-uartlite-1.00.a"; + current-speed = <115200>; + device_type = "serial"; + interrupt-parent = <µblaze_0_intc>; + interrupts = < 3 0 >; + port-number = <0>; + reg = < 0x40600000 0x10000 >; + xlnx,baudrate = <0x1c200>; + xlnx,data-bits = <0x8>; + xlnx,family = "spartan6"; + xlnx,odd-parity = <0x1>; + xlnx,s-axi-aclk-freq-hz = <0x3f940ab>; + xlnx,use-parity = <0x0>; + } ; + microblaze_0_intc: interrupt-controller at 41200000 { + #interrupt-cells = <0x2>; + compatible = "xlnx,axi-intc-1.01.a", "xlnx,xps-intc-1.00.a"; + interrupt-controller ; + reg = < 0x41200000 0x10000 >; + xlnx,kind-of-intr = <0xc>; + xlnx,num-intr-inputs = <0x4>; + } ; + system_timer: timer at 41c00000 { + clock-frequency = <66666667>; + compatible = "xlnx,axi-timer-1.02.a", "xlnx,xps-timer-1.00.a"; + interrupt-parent = <µblaze_0_intc>; + interrupts = < 0 2 >; + reg = < 0x41c00000 0x10000 >; + xlnx,count-width = <0x20>; + xlnx,family = "spartan6"; + xlnx,gen0-assert = <0x1>; + xlnx,gen1-assert = <0x1>; + xlnx,one-timer-only = <0x0>; + xlnx,trig0-assert = <0x1>; + xlnx,trig1-assert = <0x1>; + } ; + } ; +} ;
board/avnet/s6lx9_microboard/lx9_mmu_defconfig new file +68 -0
68 lines not on this page · raw message
board/avnet/s6lx9_microboard/readme.txt new file +70 -0
70 lines not on this page · raw message
configs/s6lx9_microboard_defconfig new file +17 -0
@@ -0,0 +1,17 @@ +BR2_microblaze=y +BR2_microblazeel=y +BR2_TOOLCHAIN_EXTERNAL=y +BR2_TOOLCHAIN_EXTERNAL_XILINX_MICROBLAZEEL_V2=y +BR2_TOOLCHAIN_EXTERNAL_DOWNLOAD=y +BR2_TOOLCHAIN_EXTERNAL_CUSTOM_PREFIX="microblazeel-unknown-linux-gnu" +BR2_TOOLCHAIN_EXTERNAL_CUSTOM_GLIBC=y +BR2_TOOLCHAIN_EXTERNAL_CXX=y +BR2_TARGET_GENERIC_GETTY_PORT="ttyUL0" +# BR2_TARGET_ROOTFS_TAR is not set +BR2_TARGET_ROOTFS_INITRAMFS=y +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y +BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/avnet/s6lx9_microboard/lx9_mmu_defconfig" +BR2_LINUX_KERNEL_DTS_FILE="board/avnet/s6lx9_microboard/lx9_mmu.dts" +BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y +BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="simpleImage.lx9_mmu"
Signature · 1 line
1.7.9.1
PATCH 1/1 Microblaze: build kernel with device tree
In reply to Stephan HoffmannFrom: Stephan Hoffmann <[email protected]>
This patch adds the options needed to build the SimpleImage containing the device tree structure needed for the Microblaze architecture.
Handling Device Tree and SimpleImage will be handled in a general way in the future.
I provide this patch to be able to build the system in the meantime.
--- linux/Config.in | 8 ++++++++ linux/linux.mk | 16 ++++++++++++++++ 2 files changed, 24 insertions(+), 0 deletions(-)
linux/Config.in +8 -0
@@ -120,6 +120,14 @@ config BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE help Path to the kernel configuration file +config BR2_LINUX_KERNEL_DTS_FILE + string "Device Tree dts file location" + depends on BR2_microblaze + help + Path from where the dts file has to be copied + The final "custom target" name depends on the + dts file name: + <name>.dts --> simpleImage.<name> # # Binary format #
linux/linux.mk +16 -0
@@ -117,6 +117,18 @@ endef LINUX_POST_PATCH_HOOKS += LINUX_APPLY_PATCHES +ifeq ($(KERNEL_ARCH),microblaze) +# on microblaze, we always want mkimage +LINUX_DEPENDENCIES+=host-uboot-tools + +define LINUX_COPY_DTS + if test -f "$(BR2_LINUX_KERNEL_DTS_FILE)" ; then \ + cp $(BR2_LINUX_KERNEL_DTS_FILE) $(@D)/arch/microblaze/boot/dts ; \ + else \ + echo "Cannot copy dts file!" ; \ + fi +endef +endif ifeq ($(BR2_LINUX_KERNEL_USE_DEFCONFIG),y) KERNEL_SOURCE_CONFIG = $(KERNEL_ARCH_PATH)/configs/$(call qstrip,$(BR2_LINUX_KERNEL_DEFCONFIG))_defconfig
@@ -131,6 +143,8 @@ define LINUX_CONFIGURE_CMDS $(if $(BR2_ARM_EABI), $(call KCONFIG_ENABLE_OPT,CONFIG_AEABI,$(@D)/.config), $(call KCONFIG_DISABLE_OPT,CONFIG_AEABI,$(@D)/.config)) + $(if $(BR2_microblaze), + $(call LINUX_COPY_DTS)) # As the kernel gets compiled before root filesystems are # built, we create a fake cpio file. It'll be # replaced later by the real cpio archive, and the kernel will be
@@ -215,6 +229,8 @@ $(LINUX_DIR)/.stamp_initramfs_rebuilt: $(LINUX_DIR)/.stamp_target_installed $(LI $(TARGET_MAKE_ENV) $(MAKE) $(LINUX_MAKE_FLAGS) -C $(@D) $(LINUX_IMAGE_NAME) # Copy the kernel image to its final destination cp $(LINUX_IMAGE_PATH) $(BINARIES_DIR) + # If there is a .ub file copy it to the final destination + test -f $(LINUX_IMAGE_PATH).ub && cp $(LINUX_IMAGE_PATH).ub $(BINARIES_DIR) $(Q)touch $@ # The initramfs building code must make sure this target gets called
Signature · 1 line
1.7.9.1
PATCH 1/1 Microblaze: build kernel with device tree
Quoted 2 lines · On Saturday 17 March 2012 13:13:25 Alvaro G. M wrote:
Signed-off-by Stephan Hoffmann <[email protected]>Tested-by Alvaro G. M <[email protected]>
Peter, is it convenient for you if patches are reposted to add Tested-by
and Acked-by tags, or do you prefer the way we do it up to now, just replying to the original post?
Regards,
Arnout
Signature · 6 lines
Arnout Vandecappelle arnout at mind be Senior Embedded Software Architect +32-16-286540 Essensium/Mind http://www.mind.be G.Geenslaan 9, 3001 Leuven, Belgium BE 872 984 063 RPR Leuven LinkedIn profile: http://www.linkedin.com/in/arnoutvandecappelle GPG fingerprint: 7CB5 E4CC 6C2E EFD4 6E3D A754 F963 ECAB 2450 2F1F
PATCH 1/1 Microblaze: build kernel with device tree
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
"Arnout" == Arnout Vandecappelle <[email protected]> writes:
Quoted 2 lines · Arnout> On Saturday 17 March 2012 13:13:25 Alvaro G. M wrote:
Quoted 2 lines
Signed-off-by Stephan Hoffmann <[email protected]>Tested-by Alvaro G. M <[email protected]>
Arnout> Peter, is it convenient for you if patches are reposted to add Arnout> Tested-by and Acked-by tags, or do you prefer the way we do it Arnout> up to now, just replying to the original post?
If it's just for acked-by then I prefer people just reply - But if there's any fixes to be made and the original submitter doesn't fix it, a resend with those fixes is very much appreciated, thanks.
Signature · 1 line
Bye, Peter Korsgaard
PATCH 1/2 Microblaze: build kernel with device tree
In reply to Stephan Hoffmann Many of my comments below were already made by ThomasP as well. If
you cannot incorporate them for any reason, it is courteous to say why. But probably you just hadn't noticed that he had comments on your patch.
On Saturday 17 March 2012 11:05:49 Stephan Hoffmann wrote:
[snip]
linux/linux.mk endef · line 122
Quoted 3 lines
linux/linux.mk +3
-0+ifeq ($(KERNEL_ARCH),microblaze) +# on microblaze, we always want mkimage +LINUX_DEPENDENCIES+=host-uboot-tools
Spaces around +=
And, quoting Thomas:
Can't you create a new kernel image type (along BR2_LINUX_KERNEL_UIMAGE, BR2_LINUX_KERNEL_BZIMAGE, BR2_LINUX_KERNEL_ZIMAGE, etc.) which would add this dependency?
Actually you probably have to do something like that, because with
this patch the simpleImage.xxx doesn't get copied into the images directory, right?
linux/linux.mk endef · line 125
Quoted 3 lines
linux/linux.mk +3
-0+ +define LINUX_COPY_DTS + if test -f "$(BR2_LINUX_KERNEL_DTS_FILE)" ; then \
The filename should be qstripped. So
if test -f "$(call qstrip,$(BR2_LINUX_KERNEL_DTS_FILE))"; then \
It looks a bit crazy to strip the quotes and then add them again, but
that helps to support situations where the variable is assigned from the command line.
Also, I prefer to use single quotes instead of double quotes, so nothing
gets expanded by the shell.
Quoted 1 line
+ cp $(BR2_LINUX_KERNEL_DTS_FILE) $(@D)/arch/microblaze/boot/dts ; \
Use KERNEL_ARCH_PATH instead of $(@D)/arch/microblaze, so it works on
other architectures as well.
linux/linux.mk endef · line 128
Quoted 2 lines
linux/linux.mk +2
-0+ else \ + echo "Cannot copy dts file!" ; \
This message will get lost in the long make output. Either there
should be a check at the make level (i.e. using $(error), but that's tricky to get right), or the else branch should end with an 'exit 1'. Or skip the check entirely, the kernel build will error out on it anyway.
linux/linux.mk define LINUX_CONFIGURE_CMDS · line 147
Quoted 12 lines
linux/linux.mk +5
-0+ fi +endef +endif ifeq ($(BR2_LINUX_KERNEL_USE_DEFCONFIG),y) KERNEL_SOURCE_CONFIG = $(KERNEL_ARCH_PATH)/configs/$(call qstrip,$(BR2_LINUX_KERNEL_DEFCONFIG))_defconfig@@ -131,6 +143,8 @@ define LINUX_CONFIGURE_CMDS $(if $(BR2_ARM_EABI), $(call KCONFIG_ENABLE_OPT,CONFIG_AEABI,$(@D)/.config), $(call KCONFIG_DISABLE_OPT,CONFIG_AEABI,$(@D)/.config)) + $(if $(BR2_microblaze), + $(call LINUX_COPY_DTS))
The if is not needed, the LINUX_COPY_DTS is already defined
conditionally.
linux/linux.mk $(LINUX_DIR)/.stamp_initramfs_rebuilt: $(LINUX_DIR)/.stamp_target_installed $(LI · line 233
Quoted 9 lines
linux/linux.mk +2
-0# As the kernel gets compiled before root filesystems are # built, we create a fake cpio file. It'll be # replaced later by the real cpio archive, and the kernel will be@@ -215,6 +229,8 @@ $(LINUX_DIR)/.stamp_initramfs_rebuilt: $(LINUX_DIR)/.stamp_target_installed $(LI $(TARGET_MAKE_ENV) $(MAKE) $(LINUX_MAKE_FLAGS) -C $(@D) $(LINUX_IMAGE_NAME) # Copy the kernel image to its final destination cp $(LINUX_IMAGE_PATH) $(BINARIES_DIR) + # If there is a .ub file copy it to the final destination + test -f $(LINUX_IMAGE_PATH).ub && cp $(LINUX_IMAGE_PATH).ub $(BINARIES_DIR)
I'm sorry, but that comment doesn't help me. I see that the .ub file is
copied if it exists, but what is this .ub file?
Regards,
Arnout
Quoted 4 lines
linux/linux.mk +0
-0$(Q)touch $@ # The initramfs building code must make sure this target gets called
Signature · 6 lines
Arnout Vandecappelle arnout at mind be Senior Embedded Software Architect +32-16-286540 Essensium/Mind http://www.mind.be G.Geenslaan 9, 3001 Leuven, Belgium BE 872 984 063 RPR Leuven LinkedIn profile: http://www.linkedin.com/in/arnoutvandecappelle GPG fingerprint: 7CB5 E4CC 6C2E EFD4 6E3D A754 F963 ECAB 2450 2F1F
PATCH 1/2 Microblaze: build kernel with device tree
Am 18.03.2012 19:28, schrieb Arnout Vandecappelle:
Quoted 3 lines
Many of my comments below were already made by ThomasP as well. If
you cannot incorporate them for any reason, it is courteous to say why. But probably you just hadn't noticed that he had comments on your patch.
Hello Arnout,
in fact I had noticed the comments, but lost them in the discussion about doing dts and simpleimage handling in a more general way that would make most of my patch obsolete.
You wrote:
I will not be able to addess the points within the next two or three weeks because I'm too busy. Maybe until then Spenser's patch from February is ready and I can build on it.
Kind regards
Stephan
Quoted 78 lines · On Saturday 17 March 2012 11:05:49 Stephan Hoffmann wrote:
[snip]
linux/linux.mk endef · line 122
Quoted 3 lines
linux/linux.mk +3
-0+ifeq ($(KERNEL_ARCH),microblaze) +# on microblaze, we always want mkimage +LINUX_DEPENDENCIES+=host-uboot-toolsSpaces around +=
And, quoting Thomas:
Can't you create a new kernel image type (alongBR2_LINUX_KERNEL_UIMAGE,BR2_LINUX_KERNEL_BZIMAGE,BR2_LINUX_KERNEL_ZIMAGE, etc.) which would add this dependency?Actually you probably have to do something like that, because with
this patch the simpleImage.xxx doesn't get copied into the images directory, right?linux/linux.mk endef · line 125
Quoted 3 lines
linux/linux.mk +3
-0+ +define LINUX_COPY_DTS + if test -f "$(BR2_LINUX_KERNEL_DTS_FILE)" ; then \The filename should be qstripped. So
if test -f "$(call qstrip,$(BR2_LINUX_KERNEL_DTS_FILE))"; then \
It looks a bit crazy to strip the quotes and then add them again, but
that helps to support situations where the variable is assigned from the command line.Also, I prefer to use single quotes instead of double quotes, so nothing
gets expanded by the shell.Quoted 1 line
+ cp $(BR2_LINUX_KERNEL_DTS_FILE) $(@D)/arch/microblaze/boot/dts ; \
Use
KERNEL_ARCH_PATHinstead of $(@D)/arch/microblaze, so it works on
other architectures as well.linux/linux.mk endef · line 128
Quoted 2 lines
linux/linux.mk +2
-0+ else \ + echo "Cannot copy dts file!" ; \This message will get lost in the long make output. Either there
should be a check at the make level (i.e. using $(error), but that's tricky to get right), or the else branch should end with an 'exit 1'. Or skip the check entirely, the kernel build will error out on it anyway.linux/linux.mk define LINUX_CONFIGURE_CMDS · line 147
Quoted 12 lines
linux/linux.mk +5
-0+ fi +endef +endif ifeq ($(BR2_LINUX_KERNEL_USE_DEFCONFIG),y) KERNEL_SOURCE_CONFIG = $(KERNEL_ARCH_PATH)/configs/$(call qstrip,$(BR2_LINUX_KERNEL_DEFCONFIG))_defconfig@@ -131,6 +143,8 @@ define LINUX_CONFIGURE_CMDS $(if $(BR2_ARM_EABI), $(call KCONFIG_ENABLE_OPT,CONFIG_AEABI,$(@D)/.config), $(call KCONFIG_DISABLE_OPT,CONFIG_AEABI,$(@D)/.config)) + $(if $(BR2_microblaze), + $(call LINUX_COPY_DTS))The if is not needed, the
LINUX_COPY_DTSis already defined
conditionally.linux/linux.mk $(LINUX_DIR)/.stamp_initramfs_rebuilt: $(LINUX_DIR)/.stamp_target_installed $(LI · line 233
Quoted 9 lines
linux/linux.mk +2
-0# As the kernel gets compiled before root filesystems are # built, we create a fake cpio file. It'll be # replaced later by the real cpio archive, and the kernel will be@@ -215,6 +229,8 @@ $(LINUX_DIR)/.stamp_initramfs_rebuilt: $(LINUX_DIR)/.stamp_target_installed $(LI $(TARGET_MAKE_ENV) $(MAKE) $(LINUX_MAKE_FLAGS) -C $(@D) $(LINUX_IMAGE_NAME) # Copy the kernel image to its final destination cp $(LINUX_IMAGE_PATH) $(BINARIES_DIR) + # If there is a .ub file copy it to the final destination + test -f $(LINUX_IMAGE_PATH).ub && cp $(LINUX_IMAGE_PATH).ub $(BINARIES_DIR)I'm sorry, but that comment doesn't help me. I see that the .ub file is
copied if it exists, but what is this .ub file?Regards,
ArnoutQuoted 4 lines
linux/linux.mk +0
-0$(Q)touch $@ # The initramfs building code must make sure this target gets called
Signature · 4 lines
reLinux - Stephan Hoffmann Am Schmidtgrund 124 50765 K?ln Tel. +49.221.95595-19 Fax: -64 www.reLinux.de sho at reLinux.de