mx51evk: Add LCD support

Add support for CLAA07LC0ACW LCD that connects to the mx51evk board.

Configure the board to show the Linux logo on the LCD.

Also increase the size of CONFIG_SYS_MALLOC_LEN variable to take into account the framebuffer usage.

Signed-off-by Fabio Estevam <[email protected]>

---
 board/freescale/mx51evk/mx51evk.c |   59 +++++++++++++++++++++++++++++++++++++
 include/configs/mx51evk.h         |   13 +++++++-
 2 files changed, 71 insertions(+), 1 deletions(-)

board/freescale/mx51evk/mx51evk.c +59 -0

index b505a71..90dbabb 100644
@@ -36,6 +36,12 @@
 #include <fsl_pmic.h>
 #include <mc13892.h>
 #include <usb/ehci-fsl.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+
+#define MX51EVK_LCD_3V3		(3 * 32 + 9)	/* GPIO4_9 */
+#define MX51EVK_LCD_5V		(3 * 32 + 10)	/* GPIO4_10 */
+#define MX51EVK_LCD_BACKLIGHT	(2 * 32 + 4)	/* GPIO3_4 */
 
 DECLARE_GLOBAL_DATA_PTR;
 

@@ -453,6 +459,54 @@ int board_mmc_init(bd_t *bis)
 }
 #endif
 
+static struct fb_videomode claa_wvga = {
+	.name		= "CLAA07LC0ACW",
+	.refresh	= 57,
+	.xres		= 800,
+	.yres		= 480,
+	.pixclock	= 37037,
+	.left_margin	= 40,
+	.right_margin	= 60,
+	.upper_margin	= 10,
+	.lower_margin	= 10,
+	.hsync_len	= 20,
+	.vsync_len	= 10,
+	.sync		= 0,
+	.vmode		= FB_VMODE_NONINTERLACED
+};
+
+void lcd_iomux(void)
+{
+	/* DI2_PIN15 */
+	mxc_request_iomux(MX51_PIN_DI_GP4, IOMUX_CONFIG_ALT4);
+
+	/* Pad settings for MX51_PIN_DI2_DISP_CLK */
+	mxc_iomux_set_pad(MX51_PIN_DI2_DISP_CLK, PAD_CTL_HYS_NONE |
+			  PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER |
+			  PAD_CTL_DRV_MAX | PAD_CTL_SRE_SLOW);
+
+	/* Turn on 3.3V voltage for LCD */
+	mxc_request_iomux(MX51_PIN_CSI2_D12, IOMUX_CONFIG_ALT3);
+	gpio_direction_output(MX51EVK_LCD_3V3, 1);
+
+	/* Turn on 5V voltage for LCD */
+	mxc_request_iomux(MX51_PIN_CSI2_D13, IOMUX_CONFIG_ALT3);
+	gpio_direction_output(MX51EVK_LCD_5V, 1);
+
+	/* Turn on GPIO backlight */
+	mxc_request_iomux(MX51_PIN_DI1_D1_CS, IOMUX_CONFIG_ALT4);
+	mxc_iomux_set_input(MX51_GPIO3_IPP_IND_G_IN_4_SELECT_INPUT,
+							INPUT_CTL_PATH1);
+	gpio_direction_output(MX51EVK_LCD_BACKLIGHT, 1);
+}
+
+void lcd_enable(void)
+{
+	int ret = mx51_fb_init(&claa_wvga, 1, IPU_PIX_FMT_RGB565);
+	if (ret)
+		printf("LCD cannot be configured: %d\n", ret);
+}
+
 int board_early_init_f(void)
 {
 	setup_iomux_uart();

@@ -460,6 +514,7 @@ int board_early_init_f(void)
 #ifdef CONFIG_USB_EHCI_MX5
 	setup_usb_h1();
 #endif
+	lcd_iomux();
 
 	return 0;
 }

@@ -469,6 +524,8 @@ int board_init(void)
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
 
+	lcd_enable();
+
 	return 0;
 }
 

@@ -479,6 +536,8 @@ int board_late_init(void)
 	setup_iomux_spi();
 	power_init();
 #endif
+	setenv("stdout", "serial");
+
 	return 0;
 }
 #endif

include/configs/mx51evk.h +5 -1

index 1477b21..58b6f1c 100644
@@ -51,7 +51,7 @@
 /*
  * Size of malloc() pool
  */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2 * 1024 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(10 * 1024 * 1024)
 
 #define CONFIG_BOARD_LATE_INIT
 

@@ -123,6 +123,17 @@
 #define CONFIG_MXC_USB_PORTSC	PORT_PTS_ULPI
 #define CONFIG_MXC_USB_FLAGS	MXC_EHCI_POWER_PINS_ENABLED
 
+/* Framebuffer and LCD */
+#define CONFIG_PREBOOT
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_MX5

Add support for CLAA07LC0ACW LCD that connects to the mx51evk board.

Configure the board to show the Linux logo on the LCD.

Also increase the size of CONFIG_SYS_MALLOC_LEN variable to take into account the framebuffer usage.

Signed-off-by Fabio Estevam <[email protected]>

---
 board/freescale/mx51evk/mx51evk.c |   59 +++++++++++++++++++++++++++++++++++++
 include/configs/mx51evk.h         |   13 +++++++-
 2 files changed, 71 insertions(+), 1 deletions(-)