Pull request: u-boot-arm/master

Hi Wolfgang,

Please consider applying this branch before -rc1.

The following changes since commit 18277f7057c8e9b895aa4f8590969a57c4bce888:

Revert "arm: bugfix: save_boot_params_default accesses uninitalized stack when -O0" (2012-07-09 09:19:00 +0200)

are available in the git repository at:

git://git.denx.de/u-boot-arm master

for you to fetch changes up to 63905f1616fc2f827e986d8e82a5a2b69f4a0e6a:

tegra: define fdt_load/fdt_high variables (2012-07-09 22:44:34 +0200)

----------------------------------------------------------------
Jim Lin (1):
tegra: usb: Fix device enumeration problem of USB1

Lucas Stach (2):
tegra: add ULPI on USB2 funcmux entry
tegra: usb: fix wrong error check

Peter Meerwald (1):
beagle: add eeprom expansion board info for bct brettl4

Stephen Warren (10):
Add env vars describing U-Boot target board
tegra: enable CONFIG_ENV_VARS_UBOOT_CONFIG
tegra: add enterrcm command
tegra: bootcmd enhancements
tegra: bootcmd: start USB only when needed
tegra: add GMC/GMD funcmux entry for SFLASH
tegra: add pin_mux_spi() board initialization function
tegra: trimslice: set up serial flash pinmux
tegra: enable bootz command
tegra: define fdt_load/fdt_high variables

Thierry Reding (7):
tegra: Rework Tamonten support
tegra: medcom: Add device tree support
tegra: plutux: Add device tree support
tegra: Allow boards to perform early GPIO setup
tegra: Implement gpio_early_init() on Tamonten
tegra: Use SD write-protect GPIO on Tamonten
tegra: Add Tamonten Evaluation Carrier support

Tom Warren (1):
tegra: fix leftover CONFIG_TEGRA2_MMC & _SPI build switches

 MAINTAINERS                                |    1 +
 README                                     |   14 ++++
 arch/arm/cpu/armv7/tegra2/Makefile         |    1 +
 arch/arm/cpu/armv7/tegra2/cmd_enterrcm.c   |   65 +++++++++++++++++++
 arch/arm/cpu/armv7/tegra2/funcmux.c        |   23 ++++++-
 arch/arm/cpu/armv7/tegra2/usb.c            |    2 +-
 arch/arm/include/asm/arch-tegra2/funcmux.h |    6 ++
 arch/arm/include/asm/arch-tegra2/tegra2.h  |    1 +
 board/avionic-design/common/tamonten.c     |   65 ++++++-------------
 board/avionic-design/common/tamonten.h     |   32 ----------
 board/avionic-design/dts/tegra2-medcom.dts |   58 +++++++++++++++++
 board/avionic-design/dts/tegra2-plutux.dts |   58 +++++++++++++++++
 board/avionic-design/dts/tegra2-tec.dts    |   58 +++++++++++++++++
 board/avionic-design/medcom/Makefile       |    6 +-
 board/avionic-design/medcom/medcom.c       |   45 -------------
 board/avionic-design/plutux/Makefile       |    6 +-
 board/avionic-design/plutux/plutux.c       |   45 -------------
 board/avionic-design/tec/Makefile          |   50 +++++++++++++++
 board/compal/paz00/paz00.c                 |    4 +-
 board/compulab/trimslice/trimslice.c       |    7 +-
 board/nvidia/common/board.c                |   16 ++++-
 board/nvidia/common/board.h                |    1 +
 board/ti/beagle/beagle.c                   |    8 ++-
 boards.cfg                                 |    1 +
 common/env_common.c                        |   11 ++++
 common/env_embedded.c                      |   11 ++++
 drivers/usb/host/ehci-tegra.c              |   18 +++++-
 include/configs/medcom.h                   |   21 +++++-
 include/configs/plutux.h                   |   21 +++++-
 include/configs/tec.h                      |   82 ++++++++++++++++++++++++
 include/configs/tegra2-common-post.h       |   96 ++++++++++++++++++----------
 include/configs/tegra2-common.h            |    3 +
 mkconfig                                   |    8 +++
 33 files changed, 628 insertions(+), 216 deletions(-)
 create mode 100644 arch/arm/cpu/armv7/tegra2/cmd_enterrcm.c
 delete mode 100644 board/avionic-design/common/tamonten.h
 create mode 100644 board/avionic-design/dts/tegra2-medcom.dts
 create mode 100644 board/avionic-design/dts/tegra2-plutux.dts
 create mode 100644 board/avionic-design/dts/tegra2-tec.dts
 delete mode 100644 board/avionic-design/medcom/medcom.c
 delete mode 100644 board/avionic-design/plutux/plutux.c
 create mode 100644 board/avionic-design/tec/Makefile
 create mode 100644 include/configs/tec.h

Amicalement,

Albert.

Dear Albert ARIBAUD,

Applied, thanks.

Best regards,

Wolfgang Denk

DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
F u cn rd ths u cnt spl wrth a dm!