serial: Add Zynq serial driver

The driver is used on Xilinx Zynq platform.

Signed-off-by Michal Simek <[email protected]>

CC Joe Hershberger <[email protected]>

CC Marek Vasut <[email protected]>

---
v2: Use Zynq name instead of Dragonfire and XPSS/XDFUART
Rename driver name
Remove driver description

v3: SERIAL_MULTI support
Rename xdfuart to uart_zynq

v4: Properly spell out the structure member names of serial_driver

---
 common/serial.c              |    8 ++
 drivers/serial/Makefile      |    1 +
 drivers/serial/serial_zynq.c |  247
++++++++++++++++++++++++++++++++++++++++++ include/serial.h             | 
  5 +
 4 files changed, 261 insertions(+), 0 deletions(-)
 create mode 100644 drivers/serial/serial_zynq.c

common/serial.c +8 -0

index 75cc1bb..4f2bc7f 100644
@@ -122,6 +122,14 @@ void serial_initialize(void)
 	serial_register(&uartlite_serial3_device);
 # endif /* XILINX_UARTLITE_BASEADDR3 */
 #endif /* CONFIG_XILINX_UARTLITE */
+#if defined(CONFIG_ZYNQ_SERIAL)
+# ifdef CONFIG_ZYNQ_SERIAL_BASEADDR0
+	serial_register(&uart_zynq_serial0_device);
+# endif
+# ifdef CONFIG_ZYNQ_SERIAL_BASEADDR1
+	serial_register(&uart_zynq_serial1_device);
+# endif
+#endif
 	serial_assign(default_serial_console()->name);
 }
 

drivers/serial/Makefile +1 -0

index 65d0f23..dfc22a4 100644
@@ -56,6 +56,7 @@ COBJS-$(CONFIG_S3C44B0_SERIAL) += serial_s3c44b0.o
 COBJS-$(CONFIG_XILINX_UARTLITE) += serial_xuartlite.o
 COBJS-$(CONFIG_SANDBOX_SERIAL) += sandbox.o
 COBJS-$(CONFIG_SCIF_CONSOLE) += serial_sh.o
+COBJS-$(CONFIG_ZYNQ_SERIAL) += serial_zynq.o
 
 ifndef CONFIG_SPL_BUILD
 COBJS-$(CONFIG_USB_TTY) += usbtty.o

drivers/serial/serial_zynq.c new file +70 -0

new file mode 100644
index 0000000..3832236
@@ -0,0 +1,247 @@
+/*
+ * Copyright (C) 2012 Michal Simek <[email protected]>
+ * Copyright (C) 2011-2012 Xilinx, Inc. All rights reserved.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <watchdog.h>
+#include <asm/io.h>
+#include <linux/compiler.h>
+#include <serial.h>
+
+#define ZYNQ_UART_SR_TXFULL	0x00000010 /* TX FIFO full */
+#define ZYNQ_UART_SR_RXEMPTY	0x00000002 /* RX FIFO empty */
+
+#define ZYNQ_UART_CR_TX_EN	0x00000010 /* TX enabled */
+#define ZYNQ_UART_CR_RX_EN	0x00000004 /* RX enabled */
+#define ZYNQ_UART_CR_TXRST	0x00000002 /* TX logic reset */
+#define ZYNQ_UART_CR_RXRST	0x00000001 /* RX logic reset */
+
+#define ZYNQ_UART_MR_PARITY_NONE	0x00000020  /* No parity mode */
+
+/* Some clock/baud constants */
+#define ZYNQ_UART_BDIV	15 /* Default/reset BDIV value */
+#define ZYNQ_UART_BASECLK	3125000L /* master / (bdiv + 1) */
+
+struct uart_zynq {
+	u32 control; /* Control Register [8:0] */
+	u32 mode; /* Mode Register [10:0] */
+	u32 reserved1[4];
+	u32 baud_rate_gen; /* Baud Rate Generator [15:0] */
+	u32 reserved2[4];
+	u32 channel_sts; /* Channel Status [11:0] */
+	u32 tx_rx_fifo; /* FIFO [15:0] or [7:0] */
+	u32 baud_rate_divider; /* Baud Rate Divider [7:0] */
+};
+
+static struct uart_zynq *uart_zynq_ports[2] = {
+#ifdef CONFIG_ZYNQ_SERIAL_BASEADDR0
+	[0] = (struct uart_zynq *)CONFIG_ZYNQ_SERIAL_BASEADDR0,
+#endif
+#ifdef CONFIG_ZYNQ_SERIAL_BASEADDR1
+	[1] = (struct uart_zynq *)CONFIG_ZYNQ_SERIAL_BASEADDR1,
+#endif
+};
+
+struct uart_zynq_params {
+	u32 baudrate;
+	u32 clock;
+};
+
+static struct uart_zynq_params uart_zynq_ports_param[2] = {
+#if defined(CONFIG_ZYNQ_SERIAL_BAUDRATE0) &&

defined(CONFIG_ZYNQ_SERIAL_CLOCK0) + [0].baudrate =
CONFIG_ZYNQ_SERIAL_BAUDRATE0,

drivers/serial/serial_zynq.c new file +3 -0

+	[0].clock = CONFIG_ZYNQ_SERIAL_CLOCK0,
+#endif
+#if defined(CONFIG_ZYNQ_SERIAL_BAUDRATE1) &&

defined(CONFIG_ZYNQ_SERIAL_CLOCK1) + [1].baudrate =
CONFIG_ZYNQ_SERIAL_BAUDRATE1,

drivers/serial/serial_zynq.c new file +172 -0

+	[1].clock = CONFIG_ZYNQ_SERIAL_CLOCK1,
+#endif
+};
+
+/* Set up the baud rate in gd struct */
+static void uart_zynq_serial_setbrg(const int port)
+{
+	/* Calculation results. */
+	unsigned int calc_bauderror, bdiv, bgen;
+	unsigned long calc_baud = 0;
+	unsigned long baud = uart_zynq_ports_param[port].baudrate;
+	unsigned long clock = uart_zynq_ports_param[port].clock;
+	struct uart_zynq *regs = uart_zynq_ports[port];
+
+	/*                master clock
+	 * Baud rate = ------------------
+	 *              bgen * (bdiv + 1)
+	 *
+	 * Find acceptable values for baud generation.
+	 */
+	for (bdiv = 4; bdiv < 255; bdiv++) {
+		bgen = clock / (baud * (bdiv + 1));
+		if (bgen < 2 || bgen > 65535)
+			continue;
+
+		calc_baud = clock / (bgen * (bdiv + 1));
+
+		/*
+		 * Use first calculated baudrate with
+		 * an acceptable (<3%) error
+		 */
+		if (baud > calc_baud)
+			calc_bauderror = baud - calc_baud;
+		else
+			calc_bauderror = calc_baud - baud;
+		if (((calc_bauderror * 100) / baud) < 3)
+			break;
+	}
+
+	writel(bdiv, &regs->baud_rate_divider);
+	writel(bgen, &regs->baud_rate_gen);
+}
+
+/* Initialize the UART, with...some settings. */
+static int uart_zynq_serial_init(const int port)
+{
+	struct uart_zynq *regs = uart_zynq_ports[port];
+
+	if (!regs)
+		return -1;
+
+	/* RX/TX enabled & reset */
+	writel(ZYNQ_UART_CR_TX_EN | ZYNQ_UART_CR_RX_EN | ZYNQ_UART_CR_TXRST | \
+					ZYNQ_UART_CR_RXRST, &regs->control);
+	writel(ZYNQ_UART_MR_PARITY_NONE, &regs->mode); /* 8 bit, no parity */
+	uart_zynq_serial_setbrg(port);
+
+	return 0;
+}
+
+static void uart_zynq_serial_putc(const char c, const int port)
+{
+	struct uart_zynq *regs = uart_zynq_ports[port];
+
+	while ((readl(&regs->channel_sts) & ZYNQ_UART_SR_TXFULL) != 0)
+		WATCHDOG_RESET();
+
+	if (c == '\n') {
+		writel('\r', &regs->tx_rx_fifo);
+		while ((readl(&regs->channel_sts) & ZYNQ_UART_SR_TXFULL) != 0)
+			WATCHDOG_RESET();
+	}
+	writel(c, &regs->tx_rx_fifo);
+}
+
+static void uart_zynq_serial_puts(const char *s, const int port)
+{
+	while (*s)
+		uart_zynq_serial_putc(*s++, port);
+}
+
+static int uart_zynq_serial_tstc(const int port)
+{
+	struct uart_zynq *regs = uart_zynq_ports[port];
+
+	return (readl(&regs->channel_sts) & ZYNQ_UART_SR_RXEMPTY) == 0;
+}
+
+static int uart_zynq_serial_getc(const int port)
+{
+	struct uart_zynq *regs = uart_zynq_ports[port];
+
+	while (!uart_zynq_serial_tstc(port))
+		WATCHDOG_RESET();
+	return readl(&regs->tx_rx_fifo);
+}
+
+#if !defined(CONFIG_SERIAL_MULTI)
+int serial_init(void)
+{
+	return uart_zynq_serial_init(0);
+}
+
+void serial_setbrg(void)
+{
+	uart_zynq_serial_setbrg(0);
+}
+
+void serial_putc(const char c)
+{
+	uart_zynq_serial_putc(c, 0);
+}
+
+void serial_puts(const char *s)
+{
+	uart_zynq_serial_puts(s, 0);
+}
+
+int serial_getc(void)
+{
+	return uart_zynq_serial_getc(0);
+}
+
+int serial_tstc(void)
+{
+	return uart_zynq_serial_tstc(0);
+}
+#else
+/* Multi serial device functions */
+#define DECLARE_PSSERIAL_FUNCTIONS(port) \
+	int uart_zynq##port##_init(void) \
+				{ return uart_zynq_serial_init(port); } \
+	void uart_zynq##port##_setbrg(void) \
+				{ return uart_zynq_serial_setbrg(port); } \
+	int uart_zynq##port##_getc(void) \
+				{ return uart_zynq_serial_getc(port); } \
+	int uart_zynq##port##_tstc(void) \
+				{ return uart_zynq_serial_tstc(port); } \
+	void uart_zynq##port##_putc(const char c) \
+				{ uart_zynq_serial_putc(c, port); } \
+	void uart_zynq##port##_puts(const char *s) \
+				{ uart_zynq_serial_puts(s, port); }
+
+/* Serial device descriptor */
+#define INIT_PSSERIAL_STRUCTURE(port, __name) {	\
+	  .name   = __name,			\
+	  .init   = uart_zynq##port##_init,	\
+	  .uninit = NULL,			\
+	  .setbrg = uart_zynq##port##_setbrg,	\
+	  .getc   = uart_zynq##port##_getc,	\
+	  .tstc   = uart_zynq##port##_tstc,	\
+	  .putc   = uart_zynq##port##_putc,	\
+	  .puts   = uart_zynq##port##_puts,	\
+}
+
+DECLARE_PSSERIAL_FUNCTIONS(0);
+struct serial_device uart_zynq_serial0_device =
+	INIT_PSSERIAL_STRUCTURE(0, "ttyPS0");
+DECLARE_PSSERIAL_FUNCTIONS(1);
+struct serial_device uart_zynq_serial1_device =
+	INIT_PSSERIAL_STRUCTURE(1, "ttyPS1");
+
+__weak struct serial_device *default_serial_console(void)
+{
+	if (uart_zynq_ports[0])
+		return &uart_zynq_serial0_device;
+	if (uart_zynq_ports[1])
+		return &uart_zynq_serial1_device;
+
+	return NULL;
+}
+#endif

include/serial.h +5 -1

index d76d6df..826b488 100644
@@ -90,6 +90,11 @@ extern struct serial_device bfin_serial2_device;
 extern struct serial_device bfin_serial3_device;
 #endif
 
+#if defined(CONFIG_ZYNQ_SERIAL)
+extern struct serial_device uart_zynq_serial0_device;
+extern struct serial_device uart_zynq_serial1_device;
+#endif
+
 extern void serial_register(struct serial_device *);
 extern void serial_initialize(void);
 extern void serial_stdio_init(void);
--

1.7.0.4