ppc4xx: Remove ML2 board support
Subsystems (2)
PATCH 1/1 ppc4xx: Remove ML2 board support
As the board seems to be unmaintained for some time, lets remove the support in mainline completely.
--- MAINTAINERS | 4 - arch/powerpc/include/asm/ppc4xx.h | 2 +- board/ml2/Makefile | 45 ------ board/ml2/flash.c | 300 -------------------------------------- board/ml2/init.S | 30 ---- board/ml2/ml2.c | 62 -------- board/ml2/serial.c | 115 --------------- board/ml2/u-boot.lds | 94 ------------ board/ml2/u-boot.lds.debug | 135 ----------------- boards.cfg | 1 - include/configs/ML2.h | 257 -------------------------------- 11 files changed, 1 insertion(+), 1044 deletions(-) delete mode 100644 board/ml2/Makefile delete mode 100644 board/ml2/flash.c delete mode 100644 board/ml2/init.S delete mode 100644 board/ml2/ml2.c delete mode 100644 board/ml2/serial.c delete mode 100644 board/ml2/u-boot.lds delete mode 100644 board/ml2/u-boot.lds.debug delete mode 100644 include/configs/ML2.h
MAINTAINERS +0 -4
@@ -452,10 +452,6 @@ Heiko Schocher <[email protected]> uc101 MPC5200 ve8313 MPC8313 -Peter De Schrijver <[email protected]> - - ML2 PPC4xx - Andre Schwarz <[email protected]> mergerbox MPC8377
arch/powerpc/include/asm/ppc4xx.h +1 -1
@@ -86,7 +86,7 @@/* * Configure which SDRAM/DDR/DDR2 controller is equipped */ -#if defined(CONFIG_AP1000 ) || defined(CONFIG_ML2 ) +#if defined(CONFIG_AP1000 )#define CONFIG_SDRAM_PPC4xx_IBM_SDRAM/* IBM SDRAM controller */ #endif
board/ml2/Makefile deleted +0 -45
45 lines not on this page · raw message
board/ml2/flash.c deleted +0 -300
300 lines not on this page · raw message
board/ml2/init.S deleted +0 -30
@@ -1,30 +0,0 @@ -/* - * init.S: Stubs for U-Boot initialization - * - * Copyright 2002 Mind NV - * - * http://www.mind.be/ - * - * Author : Peter De Schrijver ([email protected]) - * - * This software may be used and distributed according to the terms of - * the GNU General Public License (GPL) version 2, incorporated herein by - * reference. Drivers based on or derived from this code fall under the GPL - * and must retain the authorship, copyright and this license notice. This - * file is not a complete program and may only be used when the entire - * program is licensed under the GPL. - * - */ - -#include <asm/ppc4xx.h> - -#include <ppc_asm.tmpl> -#include <ppc_defs.h> - -#include <asm/cache.h> -#include <asm/mmu.h> - - - .globl ext_bus_cntlr_init -ext_bus_cntlr_init: - blr
board/ml2/ml2.c deleted +0 -62
62 lines not on this page · raw message
board/ml2/serial.c deleted +0 -115
115 lines not on this page · raw message
board/ml2/u-boot.lds deleted +0 -94
94 lines not on this page · raw message
board/ml2/u-boot.lds.debug deleted +0 -135
135 lines not on this page · raw message
boards.cfg +0 -1
@@ -958,7 +958,6 @@ JSE powerpc ppc4xx jse korat powerpc ppc4xx korat_perm powerpc ppc4xx korat - - korat:KORAT_PERMANENT lwmon5 powerpc ppc4xx -ML2 powerpc ppc4xx ml2 pcs440ep powerpc ppc4xx quad100hd powerpc ppc4xx sbc405 powerpc ppc4xx
include/configs/ML2.h deleted +0 -257
257 lines not on this page · raw message
Signature · 1 line
1.7.12.1
PATCH 1/1 ppc4xx: Remove AP1000 board support
As the board seems to be unmaintained for some time, lets remove the support in mainline completely.
--- arch/powerpc/cpu/ppc4xx/speed.c | 8 - arch/powerpc/include/asm/ppc4xx.h | 7 - board/amirix/ap1000/Makefile | 47 -- board/amirix/ap1000/ap1000.c | 709 ------------------------------ board/amirix/ap1000/ap1000.h | 173 -------- board/amirix/ap1000/flash.c | 900 -------------------------------------- board/amirix/ap1000/init.S | 30 -- board/amirix/ap1000/pci.c | 318 -------------- board/amirix/ap1000/powerspan.c | 750 ------------------------------- board/amirix/ap1000/powerspan.h | 170 ------- board/amirix/ap1000/serial.c | 111 ----- board/amirix/ap1000/u-boot.lds | 96 ---- boards.cfg | 1 - drivers/net/e1000.c | 42 +- include/common.h | 4 +- include/configs/AP1000.h | 247 ----------- 16 files changed, 3 insertions(+), 3610 deletions(-) delete mode 100644 board/amirix/ap1000/Makefile delete mode 100644 board/amirix/ap1000/ap1000.c delete mode 100644 board/amirix/ap1000/ap1000.h delete mode 100644 board/amirix/ap1000/flash.c delete mode 100644 board/amirix/ap1000/init.S delete mode 100644 board/amirix/ap1000/pci.c delete mode 100644 board/amirix/ap1000/powerspan.c delete mode 100644 board/amirix/ap1000/powerspan.h delete mode 100644 board/amirix/ap1000/serial.c delete mode 100644 board/amirix/ap1000/u-boot.lds delete mode 100644 include/configs/AP1000.h
arch/powerpc/cpu/ppc4xx/speed.c +0 -8
@@ -812,14 +812,6 @@ unsigned long determine_pci_clock_per(void)extern void get_sys_info (sys_info_t * sysInfo);extern ulong get_PCI_freq (void ); -#elif defined(CONFIG_AP1000 ) -void get_sys_info (sys_info_t * sysInfo) -{ - sysInfo->freqProcessor =240 *1000 *1000 ; - sysInfo->freqPLB =80 *1000 *1000 ; - sysInfo->freqPCI =33 *1000 *1000 ; -} -#elif defined(CONFIG_405 )void get_sys_info (sys_info_t * sysInfo)
arch/powerpc/include/asm/ppc4xx.h +0 -7
@@ -84,13 +84,6 @@#endif /* -* Configure which SDRAM/DDR/DDR2 controller is equipped -*/ -#if defined(CONFIG_AP1000 ) -#define CONFIG_SDRAM_PPC4xx_IBM_SDRAM/* IBM SDRAM controller */ -#endif - -/* * Common registers for all SoC's */ /* DCR registers */
board/amirix/ap1000/Makefile deleted +0 -47
47 lines not on this page · raw message
board/amirix/ap1000/ap1000.c deleted +0 -709
709 lines not on this page · raw message
board/amirix/ap1000/ap1000.h deleted +0 -173
173 lines not on this page · raw message
board/amirix/ap1000/flash.c deleted +0 -900
900 lines not on this page · raw message
board/amirix/ap1000/init.S deleted +0 -30
@@ -1,30 +0,0 @@ -/* - * init.S: Stubs for ppcboot initialization - * - * Copyright 2002 Mind NV - * - * http://www.mind.be/ - * - * Author : Peter De Schrijver (p2 at mind.be) - * - * This software may be used and distributed according to the terms of - * the GNU General Public License (GPL) version 2, incorporated herein by - * reference. Drivers based on or derived from this code fall under the GPL - * and must retain the authorship, copyright and this license notice. This - * file is not a complete program and may only be used when the entire - * program is licensed under the GPL. - * - */ - -#include <asm/ppc4xx.h> - -#include <ppc_asm.tmpl> -#include <ppc_defs.h> - -#include <asm/cache.h> -#include <asm/mmu.h> - - - .globl ext_bus_cntlr_init -ext_bus_cntlr_init: - blr
board/amirix/ap1000/pci.c deleted +0 -318
318 lines not on this page · raw message
board/amirix/ap1000/powerspan.c deleted +0 -750
750 lines not on this page · raw message
board/amirix/ap1000/powerspan.h deleted +0 -170
46 lines not on this page · raw message
board/amirix/ap1000/serial.c deleted +0 -111
111 lines not on this page · raw message
board/amirix/ap1000/u-boot.lds deleted +0 -96
96 lines not on this page · raw message
drivers/net/e1000.c +1 -41
42 lines not on this page · raw message
include/configs/AP1000.h deleted +0 -247
247 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
1.7.12.1
Part of the diff is not shown here. View the raw message.
PATCH 1/1 ppc4xx: Remove AP1000 board support
Dear Stefan Roese,
Quoted 7 lines
As the board seems to be unmaintained for some time, lets remove the support in mainline completely.
Signed-off-by Stefan Roese <[email protected]>Cc Marek Vasut <[email protected]>Cc James MacAulay <[email protected]>---
[...]
All for it, one less serial driver to care for.
Best regards,
Marek Vasut
PATCH 1/1 mpc82xx: Remove BMW board port
In reply to Stefan RoeseAs the board seems to be unmaintained for some time, lets remove the support in mainline completely.
--- arch/powerpc/cpu/mpc824x/cpu_init.c | 4 +- arch/powerpc/cpu/mpc824x/start.S | 9 +- board/bmw/Makefile | 50 -- board/bmw/README | 331 ---------- board/bmw/bmw.c | 159 ----- board/bmw/bmw.h | 86 --- board/bmw/config.mk | 30 - board/bmw/early_init.S | 1170 ----------------------------------- board/bmw/flash.c | 779 ----------------------- board/bmw/m48t59y.c | 324 ---------- board/bmw/m48t59y.h | 57 -- board/bmw/ns16550.c | 57 -- board/bmw/ns16550.h | 79 --- board/bmw/serial.c | 81 --- boards.cfg | 1 - include/configs/BMW.h | 302 --------- 16 files changed, 4 insertions(+), 3515 deletions(-) delete mode 100644 board/bmw/Makefile delete mode 100644 board/bmw/README delete mode 100644 board/bmw/bmw.c delete mode 100644 board/bmw/bmw.h delete mode 100644 board/bmw/config.mk delete mode 100644 board/bmw/early_init.S delete mode 100644 board/bmw/flash.c delete mode 100644 board/bmw/m48t59y.c delete mode 100644 board/bmw/m48t59y.h delete mode 100644 board/bmw/ns16550.c delete mode 100644 board/bmw/ns16550.h delete mode 100644 board/bmw/serial.c delete mode 100644 include/configs/BMW.h
arch/powerpc/cpu/mpc824x/cpu_init.c +2 -2
@@ -63,7 +63,7 @@ voidcpu_init_f (void) {/* MOUSSE board is initialized in asm */ -#if !defined(CONFIG_MOUSSE ) && !defined(CONFIG_BMW ) +#if !defined(CONFIG_MOUSSE ) registerunsigned long val;CONFIG_WRITE_HALFWORD (PCICR ,0x06 );/* Bus Master, respond to PCI memory space acesses*/ /* CONFIG_WRITE_HALFWORD(PCISR, 0xffff); */ /*reset PCISR*/
@@ -321,7 +321,7 @@ cpu_init_f (void)CONFIG_WRITE_WORD (MCCR1 , val |MCCR1_MEMGO );/* set memory access going */ __asm__ __volatile__("eieio" ); -#endif /* !CONFIG_MOUSSE && !CONFIG_BMW */ +#endif /* !CONFIG_MOUSSE */ }
arch/powerpc/cpu/mpc824x/start.S +2 -7
@@ -113,9 +113,6 @@ _start: in_flash: -#if defined(CONFIG_BMW) - bl early_init_f /* Must be ASM: no stack yet! */ -#endif /* * Setup BATs - cannot be done in C since we don't have a stack yet */
@@ -126,7 +123,7 @@ in_flash: mfmsr r3 ori r3, r3, (MSR_IR | MSR_DR) mtmsr r3 -#if !defined(CONFIG_BMW) + /* Enable and invalidate data cache. */ mfspr r3, HID0
@@ -158,7 +155,7 @@ in_flash: ori r3, r3, 0x0080 sync mtspr 1011, r3 -#endif /* !CONFIG_BMW */ + /* * Thisk the stack pointer *somewhere* sensible. Doesnt * matter much where as we'll move it when we relocate
@@ -498,7 +495,6 @@ relocate_code: bdnz 3b 4: -#if !defined(CONFIG_BMW) /* Unlock the data cache and invalidate locked area */ xor r0, r0, r0 mtspr 1011, r0
@@ -510,7 +506,6 @@ relocate_code: dcbi r0, r4 addi r4, r4, 32 bdnz 41b -#endif /* * Now flush the cache: note that we must start from a cache aligned
board/bmw/Makefile deleted +0 -50
50 lines not on this page · raw message
board/bmw/README deleted +0 -331
331 lines not on this page · raw message
board/bmw/bmw.c deleted +0 -159
159 lines not on this page · raw message
board/bmw/bmw.h deleted +0 -86
86 lines not on this page · raw message
board/bmw/config.mk deleted +0 -30
@@ -1,30 +0,0 @@ -# -# (C) Copyright 2001 -# Wolfgang Denk, DENX Software Engineering, wd at denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -# -# BMW board -# - -# NOTE: The flags below affect how the BCM570x driver is compiled -PLATFORM_CPPFLAGS += -DEMBEDDED -DBIG_ENDIAN_HOST -DINCLUDE_5701_AX_FIX=1\ - -DDBG=0 -DT3_JUMBO_RCV_RCB_ENTRY_COUNT=256
board/bmw/early_init.S deleted +0 -1170
1,170 lines not on this page · raw message
board/bmw/flash.c deleted +0 -779
779 lines not on this page · raw message
board/bmw/m48t59y.c deleted +0 -324
324 lines not on this page · raw message
board/bmw/m48t59y.h deleted +0 -57
16 lines not on this page · raw message
board/bmw/ns16550.c deleted +0 -57
57 lines not on this page · raw message
board/bmw/ns16550.h deleted +0 -79
79 lines not on this page · raw message
board/bmw/serial.c deleted +0 -81
81 lines not on this page · raw message
include/configs/BMW.h deleted +0 -302
302 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
1.7.12.1
Part of the diff is not shown here. View the raw message.
PATCH 1/1 mpc82xx: Remove BMW board port
Dear Stefan Roese,
Quoted 7 lines
As the board seems to be unmaintained for some time, lets remove the support in mainline completely.
Signed-off-by Stefan Roese <[email protected]>Cc Marek Vasut <[email protected]>Cc James F. Dougherty <[email protected]>Cc Wolfgang Denk <[email protected]>
[...]
One less serial driver to care for. Stefan, good job!
btw what about git format-patch -D ? ;-)
Best regards,
Marek Vasut
[U-Boot] mpc82xx: Remove BMW board port
In reply to Stefan RoeseQuoted 8 lines · Stefan Roese
As the board seems to be unmaintained for some time, lets remove the support in mainline completely.
Signed-off-by Stefan Roese <[email protected]>Cc Marek Vasut <[email protected]>Cc James F. Dougherty <[email protected]>Cc Wolfgang Denk <[email protected]>Acked-by Marek Vasut <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20121017/49acadd5/attachment.pgp>
A message that is not in the archive (sent off-list or not yet received): 5E54AA067725CE49B35C6B8358FD2CB81DF20692@SJEXCHMB10.corp.ad.broadcom.com
[U-Boot] mpc82xx: Remove BMW board port
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 4 lines · James Dougherty
Hi Tom, Hi Stefan,
I am still using this platform. Please don't remove! What do you need to have it supported?
Well, the original message you were cc'd on went about a month without reply. If you wish to bring the board back and be the responsible MAINTAINER, that's fine, but with me, but it is a commitment. Thanks!
Quoted 15 lines
Thank you! -james
-----Original Message----- From: Tom Rini
[mailto:tom.rini at gmail.com] On Behalf Of Tom Rini Sent: Wednesday, October 17, 2012 7:56 AM To: Stefan Roese Cc: u-boot at lists.denx.de; James Dougherty Subject: Re: [U-Boot] mpc82xx: Remove BMW board portQuoted 3 lines · Stefan Roese
As the board seems to be unmaintained for some time, lets remove the support in mainline completely.
Quoted 7 lines
Quoted 4 lines
Signed-off-by Stefan Roese <[email protected]> Cc: Marek Vasut<[email protected]> Cc: James F. Dougherty <[email protected]> Cc: Wolfgang Denk <[email protected]> Acked-by: Marek Vasut <[email protected]>
Applied to u-boot/master, thanks!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Mozilla - http://www.enigmail.net/
iQIcBAEBAgAGBQJQgI/YAAoJENk4IS6UOR1WPGkP+gK6en2/k+xaDxSxQ6iVyhoC ifkcTshtm/e0LKW3AnWcLsr6M54r7TvVz+7mjsHZ/XJ0NWiGOSmEtEjSGXjYF4e1 LkZfsC8+80aUVMeUUiWZaBRzbDtB7rnwr0tVu5ERC7LsU6rE0zMGDjxhqST2EEtW dOLyY98fo/IEhEx6KZ+X5VMhNZ4tvqW3QQD4f+/Z+3RRMew3wxxiQdDThLotQZSn q8A2Q29p8xs0apenfFWPyRMsdm9aBiyogxGEH5ZmwtWriEJ3FQmdymZ4H3uCm92X +CFmkr9LAQVpDdi74makkWKt3GtmlqwTXE+dbSXTYIw6wKoUVJ+C32QP6UNdWlh1 m2JVmYZydLULKaJav9cERVd19BLFq5PZCEwpVKilugb/fcBqePQ5LZtT5jraA2J5 iz+ALzlU20omvgRecxR0YpvzWtJANDnDsrbAgjJPrbF8mTp9r8r5lLSb0nPheNiJ EO/e3uKz8/Er8wbgAbFPz3Sqxdhfvuz0JSCdJYJkM9gWkfkGl4uGjFjgTjsOHMQb TQ25Ws1Vug2HW/KA2YokQofSZrjIeYWgl1tjr+SPWqMuwOcjsuffEZl9vbUcBNiA mo256ZNl0TUgwqLbadiU8SvNCYuETMv3to8XX2mxSYZ9K6gGwGOGu4A9u3o3E/TJ FkPMZKJa8ROonFKAAPZx
=NXr6
-----END PGP SIGNATURE-----
A message that is not in the archive (sent off-list or not yet received): 5E54AA067725CE49B35C6B8358FD2CB81DF22833@SJEXCHMB10.corp.ad.broadcom.com
[U-Boot] mpc82xx: Remove BMW board port
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 3 lines · James Dougherty
Hi Tom,
I never received the email.
Welp, lets move forward. If you want to be the maintainer, submit a patch that brings the board back and adds yourself and the baord to the MAINTAINERS file. The biggest expectation, aside from dealing with breakage when reported, is to test the releases, at least a little bit, on the hardware. Thanks!
- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Mozilla - http://www.enigmail.net/
iQIcBAEBAgAGBQJQgOOoAAoJENk4IS6UOR1Wqm4P/0rZafkYizqMnVkNk0gl0snl pw1JJTFsnyKTZ3k/qc4yltJIaDO7hNhW7D28k7hyvQ+ysV5hSPsgVtsSZCcMu72e Jmirn2WxlExjO25aovsxmmz8GLDN4Dz0D3iKkrXlhDVwht2RBErqOb7R9dw+XtRA LRRhU2wMAPyZk0cPMI1WzC4kxKBJzcQzksqNhm4P0rB9it1eBjWXJrBQUyuiVMfN G8355FCZw49/8EebwYSjxhShYF5iPXxBiLgqJXjuOD3iCun6yfLVe2qXoI+vX3Gs U9x8FdLQCuzOrj85LttWAEH6zEbxuZxi+85jHZ4aUdej2+MHMuDltM4gP9LBw1Dk 4FAYsE9O2acRERDJUmeazJhKRbyn5ks+Wad8mEqsAyvBOurwLuIbLGSqjs+6x2ej EvxtCnLc20+zIIMR/8l8BFSmYVX4jCqamWeJg1VRfu0ptUwvk3L3/0JSVv2tfUu+ fY2G9XDqxHJAQmQvkf9B2xFAUB8Nu3cO1DZOc+I5ay/nPfdnjhIOpmOWZhwS8bJm /C9qF0TYpvr61mv5KEllfAyBoYSQ4AdL4vn9lc07SUVR2ByR+CR7lHb5VWojCZhS S+GHZh//jJ2BBA1IyD2aMfxr2Ko8PWmLBW3xSrlB7rFQWacp9xqoRTQMl71jVnS9 pHRYlup0dNgW0k1Rk2cX
=7P4V
-----END PGP SIGNATURE-----
[U-Boot] mpc82xx: Remove BMW board port
Dear James,
it appears you wrote (as Tom quotes so):
Quoted 1 line
Quoted 1 line
I never received the email.
It appears you have a major problem with your e-mail setup, then, because none of your messages reached the mailing list either.
Please check your mail configuration.
Best regards,
Wolfgang Denk
Signature · 6 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
I have yet to add the ESP-driver to the kernel to read the mind of
the user... - Linus Torvalds in
<[email protected]>PATCH 1/1 ppc4xx: Remove ML2 board support
In reply to Stefan RoeseDear Stefan Roese,
Quoted 6 lines
As the board seems to be unmaintained for some time, lets remove the support in mainline completely.
Signed-off-by Stefan Roese <[email protected]>Cc Marek Vasut <[email protected]>Cc Peter De Schrijver <[email protected]>
[...]
And one less :)
Best regards,
Marek Vasut