Bisected regression in Linux 3.7.0-rc1, hang on login caused by replace_fd()
Subsystems (2)
Hello!
I tried the current mainline Linux on Fedora 16 x64_64 and found that I cannot login in gdm. I'm using gdm with LXDE. After a few minutes, kernel messages appear indicating a hung process gnome-settings-daemon.
Bisection found that the commit to blame is
commit 8280d16172243702ed43432f826ca6130edb4086
Author: Al Viro <[email protected]> Date: Tue Aug 21 12:11:46 2012 -0400
new helper: replace_fd()
analog of dup2(), except that it takes struct file * as source.
Signed-off-by Al Viro <[email protected]>
Reverting the part of the patch that changes fs/exec.c is sufficient to fix the login behavior.
I was able to forward port the change to the current mainline Linux. The call to replace_fd() was moved to fs/coredump.c, so the patch changes it. Also, it copies __clear_close_on_exec() and __set_open_fd() from fs/file.c
The .config file, the kernel log and the forward ported patch are attached.
I'll try to figure out why replace_fd() is not good in umh_pipe_setup(), but I'd like to report the problem as soon as possible, as it's very visible to the users and I don't want others to spend hours bisecting it.
Signature · 2 lines
Regards, Pavel Roskin
[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.7.0-rc1-main (proski@mj) (gcc version 4.6.3 20120306 (Red Hat 4.6.3-2) (GCC) ) #116 SMP Mon Oct 15 11:47:27 EDT 2012 [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.7.0-rc1-main root=UUID=69ea49b8-e1c0-494e-a5b2-3e0f4850decf ro [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cf69ffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000cf6a0000-0x00000000cf6adfff] ACPI data [ 0.000000] BIOS-e820: [mem 0x00000000cf6ae000-0x00000000cf6effff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000cf6f0000-0x00000000cf6fdfff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000ffb80000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000012fffffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI present. [ 0.000000] DMI: ECS G31T-M/G31T-M, BIOS 080014 01/07/2009 [ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] No AGP bridge found [ 0.000000] e820: last_pfn = 0x130000 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-CBFFF write-protect [ 0.000000] CC000-DFFFF uncachable [ 0.000000] E0000-EFFFF write-through [ 0.000000] F0000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask F00000000 write-back [ 0.000000] 1 base 100000000 mask FE0000000 write-back [ 0.000000] 2 base 120000000 mask FF0000000 write-back [ 0.000000] 3 base 0D0000000 mask FF0000000 uncachable [ 0.000000] 4 base 0E0000000 mask FE0000000 uncachable [ 0.000000] 5 base 0CF700000 mask FFFF00000 uncachable [ 0.000000] 6 base 0CF800000 mask FFF800000 uncachable [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] e820: update [mem 0xcf700000-0xffffffff] usable ==> reserved [ 0.000000] e820: last_pfn = 0xcf6a0 max_arch_pfn = 0x400000000 [ 0.000000] initial memory mapped: [mem 0x00000000-0x1fffffff] [ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576 [ 0.000000] init_memory_mapping: [mem 0x00000000-0xcf69ffff] [ 0.000000] [mem 0x00000000-0xcf69ffff] page 4k [ 0.000000] kernel direct mapping tables up to 0xcf69ffff @ [mem 0x1f97f000-0x1fffffff] [ 0.000000] init_memory_mapping: [mem 0x100000000-0x12fffffff] [ 0.000000] [mem 0x100000000-0x12fffffff] page 4k [ 0.000000] kernel direct mapping tables up to 0x12fffffff @ [mem 0xced1a000-0xcf69ffff] [ 0.000000] RAMDISK: [mem 0x375f0000-0x37aeffff] [ 0.000000] ACPI: RSDP 00000000000f9c40 00014 (v00 ACPIAM) [ 0.000000] ACPI: RSDT 00000000cf6a0000 00040 (v01 010709 RSDT1731 20090107 MSFT 00000097) [ 0.000000] ACPI: FACP 00000000cf6a0200 00084 (v01 010709 FACP1731 20090107 MSFT 00000097) [ 0.000000] ACPI: DSDT 00000000cf6a0440 05AF2 (v01 1AAAA 1AAAA000 00000000 INTL 20051117) [ 0.000000] ACPI: FACS 00000000cf6ae000 00040 [ 0.000000] ACPI: APIC 00000000cf6a0390 0006C (v01 010709 APIC1731 20090107 MSFT 00000097) [ 0.000000] ACPI: MCFG 00000000cf6a0400 0003C (v01 010709 OEMMCFG 20090107 MSFT 00000097) [ 0.000000] ACPI: OEMB 00000000cf6ae040 00071 (v01 010709 OEMB1731 20090107 MSFT 00000097) [ 0.000000] ACPI: HPET 00000000cf6a5f40 00038 (v01 010709 OEMHPET 20090107 MSFT 00000097) [ 0.000000] ACPI: GSCI 00000000cf6ae0c0 02024 (v01 010709 GMCHSCI 20090107 MSFT 00000097) [ 0.000000] ACPI: SSDT 00000000cf6b1330 00A7C (v01 DpgPmm CpuPm 00000012 INTL 20051117) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] [ffffea0000000000-ffffea0004bfffff] PMD -> [ffff88012b600000-ffff88012f5fffff] on node 0 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00010000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] [ 0.000000] Normal [mem 0x100000000-0x12fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00010000-0x0009efff] [ 0.000000] node 0: [mem 0x00100000-0xcf69ffff] [ 0.000000] node 0: [mem 0x100000000-0x12fffffff] [ 0.000000] On node 0 totalpages: 1046063 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 6 pages reserved [ 0.000000] DMA zone: 3913 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 16320 pages used for memmap [ 0.000000] DMA32 zone: 829152 pages, LIFO batch:31 [ 0.000000] Normal zone: 3072 pages used for memmap [ 0.000000] Normal zone: 193536 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0xffffffff base: 0xfed00000 [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] e820: [mem 0xcf6fe000-0xfedfffff] available for PCI devices [ 0.000000] setup_percpu: NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff88012fc00000 s80512 r8192 d21888 u524288 [ 0.000000] pcpu-alloc: s80512 r8192 d21888 u524288 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 1 2 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1026601 [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.7.0-rc1-main root=UUID=69ea49b8-e1c0-494e-a5b2-3e0f4850decf ro [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Memory: 4010092k/4980736k available (6008k kernel code, 796484k absent, 174160k reserved, 4833k data, 556k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU lockdep checking is enabled. [ 0.000000] NR_IRQS:4352 nr_irqs:712 16 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 5855 kB [ 0.000000] per task-struct memory footprint: 1920 bytes [ 0.000000] ------------------------ [ 0.000000] | Locking API testsuite: [ 0.000000] ---------------------------------------------------------------------------- [ 0.000000] | spin |wlock |rlock |mutex | wsem | rsem | [ 0.000000] -------------------------------------------------------------------------- [ 0.000000] A-A deadlock: ok | ok | ok | ok | ok | ok | [ 0.000000] A-B-B-A deadlock: ok | ok | ok | ok | ok | ok | [ 0.000000] A-B-B-C-C-A deadlock: ok | ok | ok | ok | ok | ok | [ 0.000000] A-B-C-A-B-C deadlock: ok | ok | ok | ok | ok | ok | [ 0.000000] A-B-B-C-C-D-D-A deadlock: ok | ok | ok | ok | ok | ok | [ 0.000000] A-B-C-D-B-D-D-A deadlock: ok | ok | ok | ok | ok | ok | [ 0.000000] A-B-C-D-B-C-D-A deadlock: ok | ok | ok | ok | ok | ok | [ 0.000000] double unlock: ok | ok | ok | ok | ok | ok | [ 0.000000] initialize held: ok | ok | ok | ok | ok | ok | [ 0.000000] bad unlock order: ok | ok | ok | ok | ok | ok | [ 0.000000] -------------------------------------------------------------------------- [ 0.000000] recursive read-lock: | ok | | ok | [ 0.000000] recursive read-lock #2: | ok | | ok | [ 0.000000] mixed read-write-lock: | ok | | ok | [ 0.000000] mixed write-read-lock: | ok | | ok | [ 0.000000] -------------------------------------------------------------------------- [ 0.000000] hard-irqs-on + irq-safe-A/12: ok | ok | ok | [ 0.000000] soft-irqs-on + irq-safe-A/12: ok | ok | ok | [ 0.000000] hard-irqs-on + irq-safe-A/21: ok | ok | ok | [ 0.000000] soft-irqs-on + irq-safe-A/21: ok | ok | ok | [ 0.000000] sirq-safe-A => hirqs-on/12: ok | ok | ok | [ 0.000000] sirq-safe-A => hirqs-on/21: ok | ok | ok | [ 0.000000] hard-safe-A + irqs-on/12: ok | ok | ok | [ 0.000000] soft-safe-A + irqs-on/12: ok | ok | ok | [ 0.000000] hard-safe-A + irqs-on/21: ok | ok | ok | [ 0.000000] soft-safe-A + irqs-on/21: ok | ok | ok | [ 0.000000] hard-safe-A + unsafe-B #1/123: ok | ok | ok | [ 0.000000] soft-safe-A + unsafe-B #1/123: ok | ok | ok | [ 0.000000] hard-safe-A + unsafe-B #1/132: ok | ok | ok | [ 0.000000] soft-safe-A + unsafe-B #1/132: ok | ok | ok | [ 0.000000] hard-safe-A + unsafe-B #1/213: ok | ok | ok | [ 0.000000] soft-safe-A + unsafe-B #1/213: ok | ok | ok | [ 0.000000] hard-safe-A + unsafe-B #1/231: ok | ok | ok | [ 0.000000] soft-safe-A + unsafe-B #1/231: ok | ok | ok | [ 0.000000] hard-safe-A + unsafe-B #1/312: ok | ok | ok | [ 0.000000] soft-safe-A + unsafe-B #1/312: ok | ok | ok | [ 0.000000] hard-safe-A + unsafe-B #1/321: ok | ok | ok | [ 0.000000] soft-safe-A + unsafe-B #1/321: ok | ok | ok | [ 0.000000] hard-safe-A + unsafe-B #2/123: ok | ok | ok | [ 0.000000] soft-safe-A + unsafe-B #2/123: ok | ok | ok | [ 0.000000] hard-safe-A + unsafe-B #2/132: ok | ok | ok | [ 0.000000] soft-safe-A + unsafe-B #2/132: ok | ok | ok | [ 0.000000] hard-safe-A + unsafe-B #2/213: ok | ok | ok | [ 0.000000] soft-safe-A + unsafe-B #2/213: ok | ok | ok | [ 0.000000] hard-safe-A + unsafe-B #2/231: ok | ok | ok | [ 0.000000] soft-safe-A + unsafe-B #2/231: ok | ok | ok | [ 0.000000] hard-safe-A + unsafe-B #2/312: ok | ok | ok | [ 0.000000] soft-safe-A + unsafe-B #2/312: ok | ok | ok | [ 0.000000] hard-safe-A + unsafe-B #2/321: ok | ok | ok | [ 0.000000] soft-safe-A + unsafe-B #2/321: ok | ok | ok | [ 0.000000] hard-irq lock-inversion/123: ok | ok | ok | [ 0.000000] soft-irq lock-inversion/123: ok | ok | ok | [ 0.000000] hard-irq lock-inversion/132: ok | ok | ok | [ 0.000000] soft-irq lock-inversion/132: ok | ok | ok | [ 0.000000] hard-irq lock-inversion/213: ok | ok | ok | [ 0.000000] soft-irq lock-inversion/213: ok | ok | ok | [ 0.000000] hard-irq lock-inversion/231: ok | ok | ok | [ 0.000000] soft-irq lock-inversion/231: ok | ok | ok | [ 0.000000] hard-irq lock-inversion/312: ok | ok | ok | [ 0.000000] soft-irq lock-inversion/312: ok | ok | ok | [ 0.000000] hard-irq lock-inversion/321: ok | ok | ok | [ 0.000000] soft-irq lock-inversion/321: ok | ok | ok | [ 0.000000] hard-irq read-recursion/123: ok | [ 0.000000] soft-irq read-recursion/123: ok | [ 0.000000] hard-irq read-recursion/132: ok | [ 0.000000] soft-irq read-recursion/132: ok | [ 0.000000] hard-irq read-recursion/213: ok | [ 0.000000] soft-irq read-recursion/213: ok | [ 0.000000] hard-irq read-recursion/231: ok | [ 0.000000] soft-irq read-recursion/231: ok | [ 0.000000] hard-irq read-recursion/312: ok | [ 0.000000] soft-irq read-recursion/312: ok | [ 0.000000] hard-irq read-recursion/321: ok | [ 0.000000] soft-irq read-recursion/321: ok | [ 0.000000] ------------------------------------------------------- [ 0.000000] Good, all 218 testcases passed! | [ 0.000000] --------------------------------- [ 0.000000] ODEBUG: 17 of 17 active objects replaced [ 0.000000] ODEBUG: selftest passed [ 0.000000] hpet clockevent registered [ 0.000000] tsc: Fast TSC calibration using PIT [ 0.000000] tsc: Detected 2394.063 MHz processor [ 0.001003] Calibrating delay loop (skipped), value calculated using timer frequency.. 4788.12 BogoMIPS (lpj=2394063) [ 0.001129] pid_max: default: 32768 minimum: 301 [ 0.002080] Mount-cache hash table entries: 256 [ 0.004100] Initializing cgroup subsys cpuacct [ 0.004164] Initializing cgroup subsys freezer [ 0.004452] CPU: Physical Processor ID: 0 [ 0.004512] CPU: Processor Core ID: 0 [ 0.004571] mce: CPU supports 6 MCE banks [ 0.004640] CPU0: Thermal monitoring enabled (TM2) [ 0.004706] process: using mwait in idle threads [ 0.004770] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4 [ 0.004770] Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32 [ 0.004770] tlb_flushall_shift: -1 [ 0.004960] debug: unmapping init [mem 0xffffffff81b23000-0xffffffff81b27fff] [ 0.005033] ACPI: Core revision 20120913 [ 0.091560] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.101633] smpboot: CPU0: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz (fam: 06, model: 0f, stepping: 0b) [ 0.102000] Performance Events: PEBS fmt0+, 4-deep LBR, Core2 events, Intel PMU driver. [ 0.102000] perf_event_intel: PEBS disabled due to CPU errata [ 0.102000] ... version: 2 [ 0.102000] ... bit width: 40 [ 0.102000] ... generic registers: 2 [ 0.102000] ... value mask: 000000ffffffffff [ 0.102000] ... max period: 000000007fffffff [ 0.102000] ... fixed-purpose events: 3 [ 0.102000] ... event mask: 0000000700000003 [ 0.103899] SMP alternatives: lockdep: fixing up alternatives [ 0.116385] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter. [ 0.103985] smpboot: Booting Node 0, Processors #1 [ 0.117631] SMP alternatives: lockdep: fixing up alternatives [ 0.117745] #2 [ 0.130544] SMP alternatives: lockdep: fixing up alternatives [ 0.130658] #3 OK [ 0.142025] Brought up 4 CPUs [ 0.142101] ---------------- [ 0.143002] | NMI testsuite: [ 0.143058] -------------------- [ 0.143115] remote IPI: ok | [ 0.148131] local IPI: ok | [ 0.158011] -------------------- [ 0.158074] Good, all 2 testcases passed! | [ 0.158149] --------------------------------- [ 0.158210] smpboot: Total of 4 processors activated (19152.50 BogoMIPS) [ 0.161006] devtmpfs: initialized [ 0.163773] PM: Registering ACPI NVS region [mem 0xcf6ae000-0xcf6effff] (270336 bytes) [ 0.165232] NET: Registered protocol family 16 [ 0.165483] kworker/u:0 (32) used greatest stack depth: 5152 bytes left [ 0.169244] ACPI: bus type pci registered [ 0.170106] PCI: Using configuration type 1 for base access [ 0.171136] kworker/u:0 (45) used greatest stack depth: 4720 bytes left [ 0.235266] bio: create slab <bio-0> at 0 [ 0.236254] ACPI: Added _OSI(Module Device) [ 0.236254] ACPI: Added _OSI(Processor Device) [ 0.236254] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.236254] ACPI: Added _OSI(Processor Aggregator Device) [ 0.241404] ACPI: EC: Look up EC in DSDT [ 0.294978] ACPI: Executed 1 blocks of module-level executable AML code [ 0.396870] ACPI: SSDT 00000000cf6b00f0 00277 (v01 DpgPmm P001Ist 00000011 INTL 20051117) [ 0.399326] ACPI: Dynamic OEM Table Load: [ 0.399424] ACPI: SSDT (null) 00277 (v01 DpgPmm P001Ist 00000011 INTL 20051117) [ 0.411519] ACPI: SSDT 00000000cf6b0580 00277 (v01 DpgPmm P002Ist 00000012 INTL 20051117) [ 0.413985] ACPI: Dynamic OEM Table Load: [ 0.414075] ACPI: SSDT (null) 00277 (v01 DpgPmm P002Ist 00000012 INTL 20051117) [ 0.426144] ACPI: SSDT 00000000cf6b0a10 00277 (v01 DpgPmm P003Ist 00000012 INTL 20051117) [ 0.428603] ACPI: Dynamic OEM Table Load: [ 0.428701] ACPI: SSDT (null) 00277 (v01 DpgPmm P003Ist 00000012 INTL 20051117) [ 0.441146] ACPI: SSDT 00000000cf6b0ea0 00277 (v01 DpgPmm P004Ist 00000012 INTL 20051117) [ 0.443644] ACPI: Dynamic OEM Table Load: [ 0.443741] ACPI: SSDT (null) 00277 (v01 DpgPmm P004Ist 00000012 INTL 20051117) [ 0.489248] ACPI: Interpreter enabled [ 0.489308] ACPI: (supports S0 S3 S5) [ 0.489734] ACPI: Using IOAPIC for interrupt routing [ 0.754661] ACPI: No dock devices found. [ 0.754727] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.761949] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.768107] PCI host bridge to bus 0000:00 [ 0.768140] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.768158] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7] [ 0.768158] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff] [ 0.768178] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff] [ 0.768251] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff] [ 0.768324] pci_bus 0000:00: root bus resource [mem 0xcf700000-0xdfffffff] [ 0.768397] pci_bus 0000:00: root bus resource [mem 0xf0000000-0xffffffff] [ 0.768529] pci 0000:00:00.0: [8086:29c0] type 00 class 0x060000 [ 0.768672] pci 0000:00:02.0: [8086:29c2] type 00 class 0x030000 [ 0.768696] pci 0000:00:02.0: reg 10: [mem 0xfe180000-0xfe1fffff] [ 0.768706] pci 0000:00:02.0: reg 14: [io 0xcc00-0xcc07] [ 0.768715] pci 0000:00:02.0: reg 18: [mem 0xd0000000-0xdfffffff pref] [ 0.768725] pci 0000:00:02.0: reg 1c: [mem 0xfe000000-0xfe0fffff] [ 0.768816] pci 0000:00:02.1: [8086:29c3] type 00 class 0x038000 [ 0.768831] pci 0000:00:02.1: reg 10: [mem 0xfdf80000-0xfdffffff] [ 0.769060] pci 0000:00:1b.0: [8086:27d8] type 00 class 0x040300 [ 0.769081] pci 0000:00:1b.0: reg 10: [mem 0xfe178000-0xfe17bfff 64bit] [ 0.769193] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 0.769266] pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400 [ 0.769381] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.769437] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300 [ 0.769494] pci 0000:00:1d.0: reg 20: [io 0xc880-0xc89f] [ 0.769557] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300 [ 0.769624] pci 0000:00:1d.1: reg 20: [io 0xc800-0xc81f] [ 0.769686] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300 [ 0.769753] pci 0000:00:1d.2: reg 20: [io 0xc480-0xc49f] [ 0.769844] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300 [ 0.769901] pci 0000:00:1d.3: reg 20: [io 0xc400-0xc41f] [ 0.769991] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320 [ 0.770023] pci 0000:00:1d.7: reg 10: [mem 0xfe177c00-0xfe177fff] [ 0.770157] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 0.770199] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401 [ 0.770323] pci 0000:00:1f.0: [8086:27b8] type 00 class 0x060100 [ 0.770450] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff) [ 0.770619] pci 0000:00:1f.1: [8086:27df] type 00 class 0x01018a [ 0.770642] pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007] [ 0.770661] pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003] [ 0.770674] pci 0000:00:1f.1: reg 18: [io 0x08f0-0x08f7] [ 0.770686] pci 0000:00:1f.1: reg 1c: [io 0x08f8-0x08fb] [ 0.770699] pci 0000:00:1f.1: reg 20: [io 0xffa0-0xffaf] [ 0.770788] pci 0000:00:1f.2: [8086:27c0] type 00 class 0x01018f [ 0.770808] pci 0000:00:1f.2: reg 10: [io 0xc080-0xc087] [ 0.770820] pci 0000:00:1f.2: reg 14: [io 0xc000-0xc003] [ 0.770832] pci 0000:00:1f.2: reg 18: [io 0xbc00-0xbc07] [ 0.770843] pci 0000:00:1f.2: reg 1c: [io 0xb880-0xb883] [ 0.770855] pci 0000:00:1f.2: reg 20: [io 0xb800-0xb80f] [ 0.770926] pci 0000:00:1f.2: PME# supported from D3hot [ 0.770961] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500 [ 0.771036] pci 0000:00:1f.3: reg 20: [io 0x0400-0x041f] [ 0.771231] pci 0000:01:00.0: [10ec:8136] type 00 class 0x020000 [ 0.771253] pci 0000:01:00.0: reg 10: [io 0xd800-0xd8ff] [ 0.771294] pci 0000:01:00.0: reg 18: [mem 0xfe2ff000-0xfe2fffff 64bit] [ 0.771340] pci 0000:01:00.0: reg 30: [mem 0xfe2c0000-0xfe2dffff pref] [ 0.771476] pci 0000:01:00.0: supports D1 D2 [ 0.771479] pci 0000:01:00.0: PME# supported from D1 D2 D3hot D3cold [ 0.771507] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.771686] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.771751] pci 0000:00:1c.0: bridge window [io 0xd000-0xdfff] [ 0.771757] pci 0000:00:1c.0: bridge window [mem 0xfe200000-0xfe2fffff] [ 0.771855] pci 0000:02:01.0: [3388:0021] type 01 class 0x060400 [ 0.772003] pci 0000:02:01.0: supports D1 D2 [ 0.772006] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot [ 0.772070] pci 0000:02:02.0: [1180:0475] type 02 class 0x060700 [ 0.772094] pci 0000:02:02.0: reg 10: [mem 0x00000000-0x00000fff] [ 0.772151] pci 0000:02:02.0: supports D1 D2 [ 0.772154] pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.772228] pci 0000:00:1e.0: PCI bridge to [bus 02-04] (subtractive decode) [ 0.772299] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff] [ 0.772304] pci 0000:00:1e.0: bridge window [mem 0xfe300000-0xfebfffff] [ 0.772312] pci 0000:00:1e.0: bridge window [mem 0xfb000000-0xfcffffff 64bit pref] [ 0.772322] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode) [ 0.772331] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode) [ 0.772340] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) [ 0.772349] pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode) [ 0.772358] pci 0000:00:1e.0: bridge window [mem 0xcf700000-0xdfffffff] (subtractive decode) [ 0.772366] pci 0000:00:1e.0: bridge window [mem 0xf0000000-0xffffffff] (subtractive decode) [ 0.772494] pci 0000:03:08.0: [168c:0013] type 00 class 0x028000 [ 0.772524] pci 0000:03:08.0: reg 10: [mem 0xfe3f0000-0xfe3fffff] [ 0.772729] pci 0000:03:09.0: [168c:0013] type 00 class 0x028000 [ 0.772758] pci 0000:03:09.0: reg 10: [mem 0xfe3e0000-0xfe3effff] [ 0.772963] pci 0000:03:0b.0: [168c:0013] type 00 class 0x028000 [ 0.772993] pci 0000:03:0b.0: reg 10: [mem 0xfe3d0000-0xfe3dffff] [ 0.773212] pci 0000:02:01.0: PCI bridge to [bus 03] [ 0.773285] pci 0000:02:01.0: bridge window [mem 0xfe300000-0xfe3fffff] [ 0.773359] pci_bus 0000:04: busn_res: can not insert [bus 04-ff] under [bus 02-04] (conflicts with (null) [bus 02-04]) [ 0.773367] pci_bus 0000:04: busn_res: [bus 04-ff] end is updated to 07 [ 0.773370] pci_bus 0000:04: busn_res: can not insert [bus 04-07] under [bus 02-04] (conflicts with (null) [bus 02-04]) [ 0.773375] pci_bus 0000:04: [bus 04-07] partially hidden behind transparent bridge 0000:02 [bus 02-04] [ 0.773492] pci_bus 0000:00: on NUMA node 0 [ 0.773516] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.779335] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 0.782786] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] [ 0.789453] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x1e) [ 1.058731] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15) [ 1.060212] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 1.061802] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15) [ 1.063292] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 1.064775] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 1.066334] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *7 10 11 12 14 15) [ 1.067823] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 1.069383] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 1.072091] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none [ 1.072205] vgaarb: loaded [ 1.072262] vgaarb: bridge control possible 0000:00:02.0 [ 1.074130] SCSI subsystem initialized [ 1.074130] ACPI: bus type scsi registered [ 1.075227] libata version 3.00 loaded. [ 1.076162] ACPI: bus type usb registered [ 1.077260] usbcore: registered new interface driver usbfs [ 1.077291] usbcore: registered new interface driver hub [ 1.078108] usbcore: registered new device driver usb [ 1.079158] Linux video capture interface: v2.00 [ 1.081227] Advanced Linux Sound Architecture Driver Initialized. [ 1.081293] PCI: Using ACPI for IRQ routing [ 1.081293] PCI: pci_cache_line_size set to 64 bytes [ 1.081293] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff] [ 1.081293] e820: reserve RAM buffer [mem 0xcf6a0000-0xcfffffff] [ 1.084135] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 1.084158] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 1.084295] hpet0: 3 comparators, 64-bit 14.318180 MHz counter [ 1.087096] Switching to clocksource hpet [ 1.132582] pnp: PnP ACPI init [ 1.132763] ACPI: bus type pnp registered [ 1.135346] pnp 00:00: [bus 00-ff] [ 1.135355] pnp 00:00: [io 0x0cf8-0x0cff] [ 1.135364] pnp 00:00: [io 0x0000-0x0cf7 window] [ 1.135372] pnp 00:00: [io 0x0d00-0xffff window] [ 1.135390] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 1.135398] pnp 00:00: [mem 0x000d0000-0x000dffff window] [ 1.135407] pnp 00:00: [mem 0xcf700000-0xdfffffff window] [ 1.135415] pnp 00:00: [mem 0xf0000000-0xffffffff window] [ 1.135911] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) [ 1.136074] pnp 00:01: [mem 0xfed14000-0xfed19fff] [ 1.136623] system 00:01: [mem 0xfed14000-0xfed19fff] has been reserved [ 1.136699] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active) [ 1.137309] pnp 00:02: [dma 4] [ 1.137318] pnp 00:02: [io 0x0000-0x000f] [ 1.137326] pnp 00:02: [io 0x0081-0x0083] [ 1.137334] pnp 00:02: [io 0x0087] [ 1.137342] pnp 00:02: [io 0x0089-0x008b] [ 1.137349] pnp 00:02: [io 0x008f] [ 1.137357] pnp 00:02: [io 0x00c0-0x00df] [ 1.137802] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) [ 1.138000] pnp 00:03: [io 0x0070-0x0071] [ 1.138047] pnp 00:03: [irq 8] [ 1.138492] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active) [ 1.138641] pnp 00:04: [io 0x0061] [ 1.139110] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 1.139260] pnp 00:05: [io 0x00f0-0x00ff] [ 1.139275] pnp 00:05: [irq 13] [ 1.139714] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active) [ 1.169335] pnp 00:06: [io 0x03f8-0x03ff] [ 1.169352] pnp 00:06: [irq 4] [ 1.169368] pnp 00:06: [dma 0 disabled] [ 1.170264] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active) [ 1.231552] pnp 00:07: [io 0x0000-0xffffffffffffffff disabled] [ 1.231561] pnp 00:07: [io 0x0a00-0x0a0f] [ 1.231569] pnp 00:07: [io 0x0a10-0x0a1f] [ 1.231577] pnp 00:07: [io 0x0a20-0x0a2f] [ 1.231584] pnp 00:07: [io 0x0a30-0x0a3f] [ 1.232116] system 00:07: [io 0x0a00-0x0a0f] has been reserved [ 1.232198] system 00:07: [io 0x0a10-0x0a1f] has been reserved [ 1.232279] system 00:07: [io 0x0a20-0x0a2f] has been reserved [ 1.232359] system 00:07: [io 0x0a30-0x0a3f] has been reserved [ 1.232431] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.234805] pnp 00:08: [io 0x0010-0x001f] [ 1.234813] pnp 00:08: [io 0x0022-0x003f] [ 1.234821] pnp 00:08: [io 0x0044-0x005f] [ 1.234829] pnp 00:08: [io 0x0062-0x0063] [ 1.234836] pnp 00:08: [io 0x0065-0x006f] [ 1.234852] pnp 00:08: [io 0x0072-0x007f] [ 1.234860] pnp 00:08: [io 0x0080] [ 1.234868] pnp 00:08: [io 0x0084-0x0086] [ 1.234876] pnp 00:08: [io 0x0088] [ 1.234884] pnp 00:08: [io 0x008c-0x008e] [ 1.234892] pnp 00:08: [io 0x0090-0x009f] [ 1.234900] pnp 00:08: [io 0x00a2-0x00bf] [ 1.234908] pnp 00:08: [io 0x00e0-0x00ef] [ 1.234916] pnp 00:08: [io 0x04d0-0x04d1] [ 1.234923] pnp 00:08: [io 0x0800-0x087f] [ 1.234932] pnp 00:08: [io 0x0000-0xffffffffffffffff disabled] [ 1.234940] pnp 00:08: [io 0x0480-0x04bf] [ 1.234948] pnp 00:08: [mem 0xfed1c000-0xfed1ffff] [ 1.234955] pnp 00:08: [mem 0xfed20000-0xfed8ffff] [ 1.235508] system 00:08: [io 0x04d0-0x04d1] has been reserved [ 1.235589] system 00:08: [io 0x0800-0x087f] has been reserved [ 1.235680] system 00:08: [io 0x0480-0x04bf] has been reserved [ 1.235768] system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 1.235851] system 00:08: [mem 0xfed20000-0xfed8ffff] has been reserved [ 1.235923] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.237601] pnp 00:09: [mem 0xfed00000-0xfed003ff] [ 1.238060] pnp 00:09: Plug and Play ACPI device, IDs PNP0103 (active) [ 1.240371] pnp 00:0a: [mem 0xffb80000-0xffbfffff] [ 1.240380] pnp 00:0a: [mem 0xfff80000-0xffffffff] [ 1.240844] pnp 00:0a: Plug and Play ACPI device, IDs INT0800 (active) [ 1.242119] pnp 00:0b: [mem 0xffc00000-0xfff7ffff] [ 1.242638] system 00:0b: [mem 0xffc00000-0xfff7ffff] has been reserved [ 1.242711] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.245762] pnp 00:0c: [io 0x0060] [ 1.245770] pnp 00:0c: [io 0x0064] [ 1.245779] pnp 00:0c: [mem 0xfec00000-0xfec00fff] [ 1.245787] pnp 00:0c: [mem 0xfee00000-0xfee00fff] [ 1.246349] system 00:0c: [mem 0xfec00000-0xfec00fff] could not be reserved [ 1.246433] system 00:0c: [mem 0xfee00000-0xfee00fff] has been reserved [ 1.246505] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.247745] pnp 00:0d: [mem 0xe0000000-0xefffffff] [ 1.248300] system 00:0d: [mem 0xe0000000-0xefffffff] has been reserved [ 1.248373] system 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.253592] pnp 00:0e: [mem 0x00000000-0x0009ffff] [ 1.253601] pnp 00:0e: [mem 0x000c0000-0x000cffff] [ 1.253609] pnp 00:0e: [mem 0x000e0000-0x000fffff] [ 1.253617] pnp 00:0e: [mem 0x00100000-0xcf6fffff] [ 1.253625] pnp 00:0e: [mem 0x00000000-0xffffffffffffffff disabled] [ 1.254193] system 00:0e: [mem 0x00000000-0x0009ffff] could not be reserved [ 1.254292] system 00:0e: [mem 0x000c0000-0x000cffff] could not be reserved [ 1.254389] system 00:0e: [mem 0x000e0000-0x000fffff] could not be reserved [ 1.254487] system 00:0e: [mem 0x00100000-0xcf6fffff] could not be reserved [ 1.254560] system 00:0e: Plug and Play ACPI device, IDs PNP0c01 (active) [ 1.258307] pnp: PnP ACPI: found 15 devices [ 1.258368] ACPI: ACPI bus type pnp unregistered [ 1.306293] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 [ 1.306368] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000 [ 1.306375] pci 0000:00:1c.0: BAR 15: assigned [mem 0xcf700000-0xcf8fffff 64bit pref] [ 1.306494] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 1.306559] pci 0000:00:1c.0: bridge window [io 0xd000-0xdfff] [ 1.306628] pci 0000:00:1c.0: bridge window [mem 0xfe200000-0xfe2fffff] [ 1.306697] pci 0000:00:1c.0: bridge window [mem 0xcf700000-0xcf8fffff 64bit pref] [ 1.306853] pci 0000:02:02.0: res[15]=[mem 0x04000000-0x03ffffff pref] get_res_add_size add_size 4000000 [ 1.306856] pci 0000:02:02.0: res[16]=[mem 0x04000000-0x03ffffff] get_res_add_size add_size 4000000 [ 1.306859] pci 0000:02:02.0: res[13]=[io 0x0100-0x00ff] get_res_add_size add_size 100 [ 1.306862] pci 0000:02:02.0: res[14]=[io 0x0100-0x00ff] get_res_add_size add_size 100 [ 1.306867] pci 0000:02:02.0: BAR 0: assigned [mem 0xf0000000-0xf0000fff] [ 1.306941] pci 0000:02:02.0: BAR 15: assigned [mem 0xf4000000-0xf7ffffff pref] [ 1.307069] pci 0000:02:02.0: BAR 16: can't assign mem (size 0x4000000) [ 1.307151] pci 0000:02:02.0: BAR 13: assigned [io 0xe000-0xe0ff] [ 1.307217] pci 0000:02:02.0: BAR 14: assigned [io 0xe400-0xe4ff] [ 1.307315] pci 0000:02:02.0: BAR 0: assigned [mem 0xf0000000-0xf0000fff] [ 1.307923] pci 0000:02:02.0: BAR 16: assigned [mem 0xf4000000-0xf7ffffff] [ 1.308015] pci 0000:02:02.0: BAR 15: can't assign mem pref (size 0x4000000) [ 1.308095] pci 0000:02:02.0: BAR 14: assigned [io 0xe000-0xe0ff] [ 1.308167] pci 0000:02:02.0: BAR 13: assigned [io 0xe400-0xe4ff] [ 1.308263] pci 0000:02:01.0: PCI bridge to [bus 03] [ 1.308330] pci 0000:02:01.0: bridge window [mem 0xfe300000-0xfe3fffff] [ 1.308406] pci 0000:02:02.0: CardBus bridge to [bus 04-07] [ 1.308470] pci 0000:02:02.0: bridge window [io 0xe400-0xe4ff] [ 1.308537] pci 0000:02:02.0: bridge window [io 0xe000-0xe0ff] [ 1.308605] pci 0000:02:02.0: bridge window [mem 0xf4000000-0xf7ffffff] [ 1.308675] pci 0000:00:1e.0: PCI bridge to [bus 02-04] [ 1.308740] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff] [ 1.308809] pci 0000:00:1e.0: bridge window [mem 0xfe300000-0xfebfffff] [ 1.308878] pci 0000:00:1e.0: bridge window [mem 0xfb000000-0xfcffffff 64bit pref] [ 1.309052] pci 0000:00:1e.0: setting latency timer to 64 [ 1.309098] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 1.309101] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 1.309103] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 1.309106] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff] [ 1.309108] pci_bus 0000:00: resource 8 [mem 0xcf700000-0xdfffffff] [ 1.309111] pci_bus 0000:00: resource 9 [mem 0xf0000000-0xffffffff] [ 1.309113] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff] [ 1.309116] pci_bus 0000:01: resource 1 [mem 0xfe200000-0xfe2fffff] [ 1.309118] pci_bus 0000:01: resource 2 [mem 0xcf700000-0xcf8fffff 64bit pref] [ 1.309121] pci_bus 0000:02: resource 0 [io 0xe000-0xefff] [ 1.309123] pci_bus 0000:02: resource 1 [mem 0xfe300000-0xfebfffff] [ 1.309126] pci_bus 0000:02: resource 2 [mem 0xfb000000-0xfcffffff 64bit pref] [ 1.309128] pci_bus 0000:02: resource 4 [io 0x0000-0x0cf7] [ 1.309130] pci_bus 0000:02: resource 5 [io 0x0d00-0xffff] [ 1.309133] pci_bus 0000:02: resource 6 [mem 0x000a0000-0x000bffff] [ 1.309135] pci_bus 0000:02: resource 7 [mem 0x000d0000-0x000dffff] [ 1.309138] pci_bus 0000:02: resource 8 [mem 0xcf700000-0xdfffffff] [ 1.309140] pci_bus 0000:02: resource 9 [mem 0xf0000000-0xffffffff] [ 1.309143] pci_bus 0000:03: resource 1 [mem 0xfe300000-0xfe3fffff] [ 1.309145] pci_bus 0000:04: resource 0 [io 0xe400-0xe4ff] [ 1.309148] pci_bus 0000:04: resource 1 [io 0xe000-0xe0ff] [ 1.309150] pci_bus 0000:04: resource 3 [mem 0xf4000000-0xf7ffffff] [ 1.309387] NET: Registered protocol family 2 [ 1.310479] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 1.312052] TCP bind hash table entries: 65536 (order: 10, 4194304 bytes) [ 1.317894] TCP: Hash tables configured (established 262144 bind 65536) [ 1.318180] TCP: reno registered [ 1.318314] UDP hash table entries: 2048 (order: 6, 327680 bytes) [ 1.318811] UDP-Lite hash table entries: 2048 (order: 6, 327680 bytes) [ 1.319752] NET: Registered protocol family 1 [ 1.319877] pci 0000:00:02.0: Boot video device [ 1.319945] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f30 [ 1.319948] pci 0000:00:1d.0: Performing full reset [ 1.319975] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0030 [ 1.319977] pci 0000:00:1d.1: Performing full reset [ 1.320047] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0030 [ 1.320049] pci 0000:00:1d.2: Performing full reset [ 1.320075] pci 0000:00:1d.3: uhci_check_and_reset_hc: legsup = 0x0030 [ 1.320077] pci 0000:00:1d.3: Performing full reset [ 1.320230] PCI: CLS 32 bytes, default 64 [ 1.320754] Unpacking initramfs... [ 1.471449] debug: unmapping init [mem 0xffff8800375f0000-0xffff880037aeffff] [ 1.471682] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 1.471755] software IO TLB [mem 0xcad1a000-0xced19fff] (64MB) mapped at [ffff8800cad1a000-ffff8800ced19fff] [ 1.479131] microcode: CPU0 sig=0x6fb, pf=0x10, revision=0xb6 [ 1.479234] microcode: CPU1 sig=0x6fb, pf=0x10, revision=0xb6 [ 1.479336] microcode: CPU2 sig=0x6fb, pf=0x10, revision=0xb6 [ 1.479442] microcode: CPU3 sig=0x6fb, pf=0x10, revision=0xb6 [ 1.480040] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba [ 1.480333] sha1_ssse3: Using SSSE3 optimized SHA-1 implementation [ 1.482518] audit: initializing netlink socket (disabled) [ 1.482663] type=2000 audit(1254540657.481:1): initialized [ 1.485415] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.557068] fuse init (API version 7.20) [ 1.558648] msgmni has been set to 7832 [ 1.562067] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.562188] io scheduler noop registered [ 1.563222] io scheduler cfq registered (default) [ 1.564478] list_sort_test: start testing list_sort() [ 1.572863] intel_idle: does not run on family 6 model 15 [ 1.573727] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 [ 1.573897] ACPI: Power Button [PWRB] [ 1.574686] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.574805] ACPI: Power Button [PWRF] [ 1.576921] ACPI: Requesting acpi_cpufreq [ 1.896649] thermal LNXTHERM:00: registered as thermal_zone0 [ 1.896717] ACPI: Thermal Zone [THRM] (30 C) [ 1.897633] GHES: HEST is not enabled! [ 1.898255] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.919132] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.925216] Linux agpgart interface v0.103 [ 1.926237] agpgart-intel 0000:00:00.0: Intel G33 Chipset [ 1.926491] agpgart-intel 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable [ 1.927535] agpgart-intel 0000:00:00.0: detected 8192K stolen memory [ 1.928422] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000 [ 1.929165] [drm] Initialized drm 1.1.0 20060810 [ 1.934678] i915 0000:00:02.0: setting latency timer to 64 [ 1.980943] i915 0000:00:02.0: irq 40 for MSI/MSI-X [ 1.981095] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 1.981164] [drm] Driver supports precise vblank timestamp query. [ 1.981596] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 2.072707] [drm] initialized overlay support [ 2.174099] fbcon: inteldrmfb (fb0) is primary device [ 2.224349] [drm] Setting output timings on SDVOB failed [ 2.238067] [drm] Setting input timings on SDVOB failed [ 2.314668] Console: switching to colour frame buffer device 240x67 [ 2.320601] fb0: inteldrmfb frame buffer device [ 2.320624] drm: registered panic notifier [ 2.320747] i915: No ACPI video bus found [ 2.321182] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 2.334316] loop: module loaded [ 2.336851] ata_piix 0000:00:1f.1: version 2.13 [ 2.337075] ata_piix 0000:00:1f.1: setting latency timer to 64 [ 2.343937] scsi0 : ata_piix [ 2.386267] scsi1 : ata_piix [ 2.426170] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 [ 2.426207] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 [ 2.426375] ata_piix 0000:00:1f.2: MAP [ [ 2.426406] P0 P2 P1 P3 ] [ 2.426595] ata_piix 0000:00:1f.2: setting latency timer to 64 [ 2.432540] scsi2 : ata_piix [ 2.473148] tsc: Refined TSC clocksource calibration: 2393.999 MHz [ 2.473231] Switching to clocksource tsc [ 2.482410] scsi3 : ata_piix [ 2.530796] ata3: SATA max UDMA/133 cmd 0xc080 ctl 0xc000 bmdma 0xb800 irq 19 [ 2.530834] ata4: SATA max UDMA/133 cmd 0xbc00 ctl 0xb880 bmdma 0xb808 irq 19 [ 2.531572] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 2.531956] r8169 0000:01:00.0: irq 41 for MSI/MSI-X [ 2.533893] r8169 0000:01:00.0 eth0: RTL8101e at 0xffffc9000002e000, 00:1e:90:a5:f6:e2, XID 94200000 IRQ 41 [ 2.534542] yenta_cardbus 0000:02:02.0: CardBus bridge found [0000:0000] [ 2.534598] yenta_cardbus 0000:02:02.0: CardBus bridge to [bus 04-07] [ 2.534632] yenta_cardbus 0000:02:02.0: bridge window [io 0xe400-0xe4ff] [ 2.534670] yenta_cardbus 0000:02:02.0: bridge window [io 0xe000-0xe0ff] [ 2.534709] yenta_cardbus 0000:02:02.0: bridge window [mem 0xfb000000-0xfb3fffff pref] [ 2.534753] yenta_cardbus 0000:02:02.0: bridge window [mem 0xf4000000-0xf7ffffff] [ 2.682366] ata4.01: NODEV after polling detection [ 2.686374] ata3.00: ATA-7: INTEL SSDSA2M080G2GN, 2CV102HD, max UDMA/133 [ 2.686417] ata3.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 2.688544] ata4.00: ATAPI: TSSTcorpCD/DVDW SH-S183L, SB03, max UDMA/33 [ 2.688586] ata4.00: applying bridge limits [ 2.688676] ata3.00: failed to get Identify Device Data, Emask 0x1 [ 2.693566] ata3.00: failed to get Identify Device Data, Emask 0x1 [ 2.693574] ata3.00: configured for UDMA/133 [ 2.694669] scsi 2:0:0:0: Direct-Access ATA INTEL SSDSA2M080 2CV1 PQ: 0 ANSI: 5 [ 2.697194] ata4.00: configured for UDMA/33 [ 2.699814] sd 2:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB) [ 2.700905] sd 2:0:0:0: [sda] Write Protect is off [ 2.700935] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.701063] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 2.701250] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.705348] sda: sda1 sda2 [ 2.707886] scsi 3:0:0:0: CD-ROM TSSTcorp CD/DVDW SH-S183L SB03 PQ: 0 ANSI: 5 [ 2.710052] sd 2:0:0:0: [sda] Attached SCSI disk [ 2.717450] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.719067] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.722655] sr 3:0:0:0: Attached scsi CD-ROM sr0 [ 2.724222] sr 3:0:0:0: Attached scsi generic sg1 type 5 [ 2.706157] ACPI: Invalid Power Resource to register! [ 2.730162] ACPI: Invalid Power Resource to register!<6>[ 2.852978] yenta_cardbus 0000:02:02.0: ISA IRQ mask 0x0000, PCI irq 19 [ 2.854526] yenta_cardbus 0000:02:02.0: Socket status: 30000820 [ 2.856054] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #04 to #07 [ 2.857675] yenta_cardbus 0000:02:02.0: pcmcia: parent PCI bridge window: [io 0xe000-0xefff] [ 2.859220] yenta_cardbus 0000:02:02.0: pcmcia: parent PCI bridge window: [mem 0xfe300000-0xfebfffff] [ 2.860759] pcmcia_socket pcmcia_socket0: cs: memory probe 0xfe300000-0xfebfffff: [ 2.862398] excluding 0xfe300000-0xfe41ffff [ 2.864291] yenta_cardbus 0000:02:02.0: pcmcia: parent PCI bridge window: [mem 0xfb000000-0xfcffffff 64bit pref] [ 2.865867] pcmcia_socket pcmcia_socket0: cs: memory probe 0xfb000000-0xfcffffff: [ 2.867869] excluding 0xfb000000-0xfcffffff [ 2.873741] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.875345] ehci_hcd: block sizes: qh 104 qtd 96 itd 192 sitd 96 [ 2.875541] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 2.875546] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 2.877265] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 2.878850] ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc ports=8 [ 2.878855] ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr [ 2.879013] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 2.882911] ehci_hcd 0000:00:1d.7: debug port 1 [ 2.884459] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported [ 2.884462] ehci_hcd 0000:00:1d.7: supports USB remote wakeup [ 2.884652] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfe177c00 [ 2.886180] ehci_hcd 0000:00:1d.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 2.892332] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 2.894379] usb usb1: default language 0x0409 [ 2.894575] usb usb1: udev 1, busnum 1, minor = 0 [ 2.894578] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.896094] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.897582] usb usb1: Product: EHCI Host Controller [ 2.899086] usb usb1: Manufacturer: Linux 3.7.0-rc1-main ehci_hcd [ 2.900559] usb usb1: SerialNumber: 0000:00:1d.7 [ 2.903293] usb usb1: usb_probe_device [ 2.903297] usb usb1: configuration #1 chosen from 1 choice [ 2.903515] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 2.904137] hub 1-0:1.0: usb_probe_interface [ 2.904140] hub 1-0:1.0: usb_probe_interface - got id [ 2.904149] hub 1-0:1.0: USB hub found [ 2.905771] hub 1-0:1.0: 8 ports detected [ 2.907256] hub 1-0:1.0: standalone hub [ 2.907259] hub 1-0:1.0: no power switching (usb 1.0) [ 2.907261] hub 1-0:1.0: individual port over-current protection [ 2.907265] hub 1-0:1.0: power on to power good time: 20ms [ 2.907477] hub 1-0:1.0: local power source is good [ 2.908784] hub 1-0:1.0: trying to enable port power on non-switchable hub [ 2.910129] uhci_hcd: USB Universal Host Controller Interface driver [ 2.912307] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.912312] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 2.913825] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.915355] uhci_hcd 0000:00:1d.0: detected 2 ports [ 2.916823] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 2.916826] uhci_hcd 0000:00:1d.0: Performing full reset [ 2.916839] uhci_hcd 0000:00:1d.0: supports USB remote wakeup [ 2.916879] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000c880 [ 2.918709] usb usb2: default language 0x0409 [ 2.918893] usb usb2: udev 1, busnum 2, minor = 128 [ 2.918896] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.920394] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.921882] usb usb2: Product: UHCI Host Controller [ 2.923382] usb usb2: Manufacturer: Linux 3.7.0-rc1-main uhci_hcd [ 2.924873] usb usb2: SerialNumber: 0000:00:1d.0 [ 2.927378] usb usb2: usb_probe_device [ 2.927382] usb usb2: configuration #1 chosen from 1 choice [ 2.927474] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 2.928013] hub 2-0:1.0: usb_probe_interface [ 2.928016] hub 2-0:1.0: usb_probe_interface - got id [ 2.928021] hub 2-0:1.0: USB hub found [ 2.929614] hub 2-0:1.0: 2 ports detected [ 2.931100] hub 2-0:1.0: standalone hub [ 2.931102] hub 2-0:1.0: no power switching (usb 1.0) [ 2.931104] hub 2-0:1.0: individual port over-current protection [ 2.931108] hub 2-0:1.0: power on to power good time: 2ms [ 2.931233] hub 2-0:1.0: local power source is good [ 2.931598] hub 2-0:1.0: trying to enable port power on non-switchable hub [ 2.932247] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0 [ 2.932336] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 2.932341] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 2.933878] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 2.935404] uhci_hcd 0000:00:1d.1: detected 2 ports [ 2.936862] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 2.936865] uhci_hcd 0000:00:1d.1: Performing full reset [ 2.936878] uhci_hcd 0000:00:1d.1: supports USB remote wakeup [ 2.936918] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000c800 [ 2.938667] usb usb3: default language 0x0409 [ 2.938851] usb usb3: udev 1, busnum 3, minor = 256 [ 2.938854] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.940318] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.941772] usb usb3: Product: UHCI Host Controller [ 2.943248] usb usb3: Manufacturer: Linux 3.7.0-rc1-main uhci_hcd [ 2.944724] usb usb3: SerialNumber: 0000:00:1d.1 [ 2.947264] usb usb3: usb_probe_device [ 2.947268] usb usb3: configuration #1 chosen from 1 choice [ 2.947390] usb usb3: adding 3-0:1.0 (config #1, interface 0) [ 2.947914] hub 3-0:1.0: usb_probe_interface [ 2.947917] hub 3-0:1.0: usb_probe_interface - got id [ 2.947922] hub 3-0:1.0: USB hub found [ 2.949496] hub 3-0:1.0: 2 ports detected [ 2.950985] hub 3-0:1.0: standalone hub [ 2.950987] hub 3-0:1.0: no power switching (usb 1.0) [ 2.950989] hub 3-0:1.0: individual port over-current protection [ 2.950993] hub 3-0:1.0: power on to power good time: 2ms [ 2.951114] hub 3-0:1.0: local power source is good [ 2.951487] hub 3-0:1.0: trying to enable port power on non-switchable hub [ 2.952114] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1 [ 2.952201] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 2.952205] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 2.953706] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 2.955323] uhci_hcd 0000:00:1d.2: detected 2 ports [ 2.956788] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 2.956791] uhci_hcd 0000:00:1d.2: Performing full reset [ 2.956804] uhci_hcd 0000:00:1d.2: supports USB remote wakeup [ 2.956989] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000c480 [ 2.958740] usb usb4: default language 0x0409 [ 2.958921] usb usb4: udev 1, busnum 4, minor = 384 [ 2.958925] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.960384] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.961818] usb usb4: Product: UHCI Host Controller [ 2.963254] usb usb4: Manufacturer: Linux 3.7.0-rc1-main uhci_hcd [ 2.964689] usb usb4: SerialNumber: 0000:00:1d.2 [ 2.967140] usb usb4: usb_probe_device [ 2.967143] usb usb4: configuration #1 chosen from 1 choice [ 2.967250] usb usb4: adding 4-0:1.0 (config #1, interface 0) [ 2.967788] hub 4-0:1.0: usb_probe_interface [ 2.967791] hub 4-0:1.0: usb_probe_interface - got id [ 2.967796] hub 4-0:1.0: USB hub found [ 2.969340] hub 4-0:1.0: 2 ports detected [ 2.970740] hub 4-0:1.0: standalone hub [ 2.970743] hub 4-0:1.0: no power switching (usb 1.0) [ 2.970745] hub 4-0:1.0: individual port over-current protection [ 2.970749] hub 4-0:1.0: power on to power good time: 2ms [ 2.970863] hub 4-0:1.0: local power source is good [ 2.971211] hub 4-0:1.0: trying to enable port power on non-switchable hub [ 2.971802] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2 [ 2.971883] uhci_hcd 0000:00:1d.3: setting latency timer to 64 [ 2.971887] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 2.973314] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 [ 2.974705] uhci_hcd 0000:00:1d.3: detected 2 ports [ 2.976070] uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0000 [ 2.976073] uhci_hcd 0000:00:1d.3: Performing full reset [ 2.976086] uhci_hcd 0000:00:1d.3: supports USB remote wakeup [ 2.976271] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000c400 [ 2.977916] usb usb5: default language 0x0409 [ 2.978110] usb usb5: udev 1, busnum 5, minor = 512 [ 2.978113] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.979466] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.980820] usb usb5: Product: UHCI Host Controller [ 2.982165] usb usb5: Manufacturer: Linux 3.7.0-rc1-main uhci_hcd [ 2.983492] usb usb5: SerialNumber: 0000:00:1d.3 [ 2.985829] usb usb5: usb_probe_device [ 2.985833] usb usb5: configuration #1 chosen from 1 choice [ 2.985950] usb usb5: adding 5-0:1.0 (config #1, interface 0) [ 2.986494] hub 5-0:1.0: usb_probe_interface [ 2.986497] hub 5-0:1.0: usb_probe_interface - got id [ 2.986502] hub 5-0:1.0: USB hub found [ 2.987909] hub 5-0:1.0: 2 ports detected [ 2.989229] hub 5-0:1.0: standalone hub [ 2.989231] hub 5-0:1.0: no power switching (usb 1.0) [ 2.989233] hub 5-0:1.0: individual port over-current protection [ 2.989237] hub 5-0:1.0: power on to power good time: 2ms [ 2.989350] hub 5-0:1.0: local power source is good [ 2.989698] hub 5-0:1.0: trying to enable port power on non-switchable hub [ 2.990433] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.3 [ 2.991286] usbcore: registered new interface driver cdc_acm [ 2.992570] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 2.994142] usbcore: registered new interface driver uas [ 2.995420] Initializing USB Mass Storage driver... [ 2.997048] usbcore: registered new interface driver usb-storage [ 2.998327] USB Mass Storage support registered. [ 3.000812] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 3.003198] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 3.004604] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 3.007350] mousedev: PS/2 mouse device common for all mice [ 3.009221] ehci_hcd 0000:00:1d.7: GetStatus port:2 status 001403 0 ACK POWER sig=k CSC CONNECT [ 3.009241] hub 1-0:1.0: port 2: status 0501 change 0001 [ 3.009329] ehci_hcd 0000:00:1d.7: GetStatus port:3 status 001803 0 ACK POWER sig=j CSC CONNECT [ 3.009347] hub 1-0:1.0: port 3: status 0501 change 0001 [ 3.009395] ehci_hcd 0000:00:1d.7: GetStatus port:4 status 001803 0 ACK POWER sig=j CSC CONNECT [ 3.009413] hub 1-0:1.0: port 4: status 0501 change 0001 [ 3.010878] rtc_cmos 00:03: RTC can wake from S4 [ 3.013325] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 3.014679] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs [ 3.016425] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt [ 3.020162] coretemp coretemp.0: Using relative temperature scale! [ 3.021533] coretemp coretemp.0: Using relative temperature scale! [ 3.022882] coretemp coretemp.0: Using relative temperature scale! [ 3.024195] coretemp coretemp.0: Using relative temperature scale! [ 3.025516] it87: Found IT8718F chip at 0xa10, revision 4 [ 3.026758] it87: VID is disabled (pins used for GPIO) [ 3.030667] it87_wdt: Chip IT8718 revision 4 initialized. timeout=60 sec (nowayout=0 testmode=0 exclusive=1 nogameport=0) [ 3.031537] uhci_hcd 0000:00:1d.0: port 2 portsc 008a,00 [ 3.032033] cpuidle: using governor ladder [ 3.033319] cpuidle: using governor menu [ 3.042697] usbcore: registered new interface driver usbhid [ 3.043992] usbhid: USB HID core driver [ 3.047461] snd_hda_intel 0000:00:1b.0: irq 42 for MSI/MSI-X [ 3.051532] uhci_hcd 0000:00:1d.1: port 1 portsc 008a,00 [ 3.051623] uhci_hcd 0000:00:1d.1: port 2 portsc 0082,00 [ 3.071912] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 3.075651] TCP: cubic registered [ 3.076933] Initializing XFRM netlink socket [ 3.078282] NET: Registered protocol family 17 [ 3.084047] registered taskstats version 1 [ 3.087762] rtc_cmos 00:03: setting system clock to 2009-10-03 03:31:00 UTC (1254540660) [ 3.089125] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 3.109136] hub 1-0:1.0: state 7 ports 8 chg 001c evt 0000 [ 3.109189] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s [ 3.109294] ehci_hcd 0000:00:1d.7: port 2 low speed --> companion [ 3.124847] ALSA device list: [ 3.126142] #0: HDA Intel at 0xfe178000 irq 42 [ 3.127988] debug: unmapping init [mem 0xffffffff81a98000-0xffffffff81b22fff] [ 3.129338] Write protecting the kernel read-only data: 10240k [ 3.130833] Testing CPA: undo ffffffff81000000-ffffffff81a00000 [ 3.132319] Testing CPA: again [ 3.133771] debug: unmapping init [mem 0xffff8800015e1000-0xffff8800015fffff] [ 3.135126] debug: unmapping init [mem 0xffff880001896000-0xffff8800019fffff] [ 3.160062] ehci_hcd 0000:00:1d.7: GetStatus port:2 status 003002 0 ACK POWER OWNER sig=se0 CSC [ 3.160290] hub 1-0:1.0: port 3, status 0501, change 0000, 480 Mb/s [ 3.211330] ehci_hcd 0000:00:1d.7: port 3 full speed --> companion [ 3.211338] ehci_hcd 0000:00:1d.7: GetStatus port:3 status 003801 0 ACK POWER OWNER sig=j CONNECT [ 3.211360] hub 1-0:1.0: port 3 not reset yet, waiting 50ms [ 3.262080] ehci_hcd 0000:00:1d.7: GetStatus port:3 status 003002 0 ACK POWER OWNER sig=se0 CSC [ 3.262248] hub 1-0:1.0: port 4, status 0501, change 0000, 480 Mb/s [ 3.278592] dracut: dracut-018-60.git20120927.fc16 [ 3.313207] ehci_hcd 0000:00:1d.7: port 4 full speed --> companion [ 3.313214] ehci_hcd 0000:00:1d.7: GetStatus port:4 status 003801 0 ACK POWER OWNER sig=j CONNECT [ 3.313237] hub 1-0:1.0: port 4 not reset yet, waiting 50ms [ 3.333927] udevd[935]: starting version 173 [ 3.365074] ehci_hcd 0000:00:1d.7: GetStatus port:4 status 003002 0 ACK POWER OWNER sig=se0 CSC [ 3.365219] hub 1-0:1.0: state 7 ports 8 chg 0000 evt 001c [ 3.365239] ehci_hcd 0000:00:1d.7: GetStatus port:2 status 003002 0 ACK POWER OWNER sig=se0 CSC [ 3.365286] hub 1-0:1.0: port 2, status 0100, change 0001, 12 Mb/s [ 3.470317] hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100 [ 3.470344] ehci_hcd 0000:00:1d.7: GetStatus port:3 status 003002 0 ACK POWER OWNER sig=se0 CSC [ 3.470393] hub 1-0:1.0: port 3, status 0100, change 0001, 12 Mb/s [ 3.508932] dracut: Starting plymouth daemon [ 3.575079] hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100 [ 3.575102] ehci_hcd 0000:00:1d.7: GetStatus port:4 status 003002 0 ACK POWER OWNER sig=se0 CSC [ 3.575150] hub 1-0:1.0: port 4, status 0100, change 0001, 12 Mb/s [ 3.680061] hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x100 [ 3.680074] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 3.680099] uhci_hcd 0000:00:1d.0: port 2 portsc 01a3,00 [ 3.680152] hub 2-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s [ 3.745035] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0 [ 3.746512] pci 0000:04:00.0: [168c:0013] type 00 class 0x028000 [ 3.746548] pci 0000:04:00.0: reg 10: [mem 0x00000000-0x0000ffff] [ 3.746737] pci 0000:04:00.0: BAR 0: assigned [mem 0xf4000000-0xf400ffff] [ 3.784081] hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301 [ 3.886080] usb 2-2: new low-speed USB device number 2 using uhci_hcd [ 4.003303] ata_id (1514) used greatest stack depth: 4336 bytes left [ 4.023974] ata_id (1535) used greatest stack depth: 3680 bytes left [ 4.033565] usb 2-2: skipped 1 descriptor after interface [ 4.033577] usb 2-2: skipped 1 descriptor after interface [ 4.038548] usb 2-2: default language 0x0409 [ 4.055566] usb 2-2: udev 2, busnum 2, minor = 129 [ 4.055571] usb 2-2: New USB device found, idVendor=046d, idProduct=c312 [ 4.057321] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.058889] usb 2-2: Product: USB Multimedia Keyboard [ 4.060467] usb 2-2: Manufacturer: BTC [ 4.067513] usb 2-2: usb_probe_device [ 4.067519] usb 2-2: configuration #1 chosen from 1 choice [ 4.070722] usb 2-2: adding 2-2:1.0 (config #1, interface 0) [ 4.074825] usbhid 2-2:1.0: usb_probe_interface [ 4.074830] usbhid 2-2:1.0: usb_probe_interface - got id [ 4.096971] input: BTC USB Multimedia Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input2 [ 4.098881] uhci_hcd 0000:00:1d.0: reserve dev 2 ep81-INT, period 8, phase 4, 118 us [ 4.103297] hid-generic 0003:046D:C312.0001: input,hidraw0: USB HID v1.10 Keyboard [BTC USB Multimedia Keyboard] on usb-0000:00:1d.0-2/input0 [ 4.105331] usb 2-2: adding 2-2:1.1 (config #1, interface 1) [ 4.109661] usbhid 2-2:1.1: usb_probe_interface [ 4.109666] usbhid 2-2:1.1: usb_probe_interface - got id [ 4.154661] input: BTC USB Multimedia Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.1/input/input3 [ 4.154724] uhci_hcd 0000:00:1d.0: reserve dev 2 ep82-INT, period 8, phase 4, 118 us [ 4.156057] usbhid 2-2:1.1: looking for a minor, starting at 0 [ 4.157984] hid-generic 0003:046D:C312.0002: input,hiddev0,hidraw1: USB HID v1.10 Device [BTC USB Multimedia Keyboard] on usb-0000:00:1d.0-2/input1 [ 4.158484] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0006 [ 4.158509] uhci_hcd 0000:00:1d.1: port 1 portsc 0093,00 [ 4.158558] hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s [ 4.204034] usb usb4: suspend_rh (auto-stop) [ 4.204062] usb usb5: suspend_rh (auto-stop) [ 4.263069] hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 [ 4.264520] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 4.337850] dracut: Checking ext4: /dev/disk/by-uuid/69ea49b8-e1c0-494e-a5b2-3e0f4850decf [ 4.339702] dracut: issuing e2fsck -a /dev/disk/by-uuid/69ea49b8-e1c0-494e-a5b2-3e0f4850decf [ 4.358998] dracut: /dev/disk/by-uuid/69ea49b8-e1c0-494e-a5b2-3e0f4850decf: clean, 1698284/4505600 files, 10113788/18001664 blocks [ 4.362277] dracut: Remounting /dev/disk/by-uuid/69ea49b8-e1c0-494e-a5b2-3e0f4850decf with -o ro [ 4.365077] usb 3-1: new full-speed USB device number 2 using uhci_hcd [ 4.413930] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 4.431801] dracut: Mounted root filesystem /dev/sda1 [ 4.479287] readlink (1698) used greatest stack depth: 3216 bytes left [ 4.487137] usb 3-1: ep0 maxpacket = 8 [ 4.519559] usb 3-1: skipped 1 descriptor after interface [ 4.519571] usb 3-1: skipped 1 descriptor after interface [ 4.519581] usb 3-1: skipped 1 descriptor after interface [ 4.524533] usb 3-1: default language 0x0409 [ 4.539549] usb 3-1: udev 2, busnum 3, minor = 257 [ 4.539554] usb 3-1: New USB device found, idVendor=046d, idProduct=c52b [ 4.541528] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.543338] usb 3-1: Product: USB Receiver [ 4.545101] usb 3-1: Manufacturer: Logitech [ 4.546147] dracut: Switching root [ 4.549364] usb 3-1: usb_probe_device [ 4.549368] usb 3-1: configuration #1 chosen from 1 choice [ 4.554558] usb 3-1: adding 3-1:1.0 (config #1, interface 0) [ 4.555174] usbhid 3-1:1.0: usb_probe_interface [ 4.555178] usbhid 3-1:1.0: usb_probe_interface - got id [ 4.558018] usb 3-1: adding 3-1:1.1 (config #1, interface 1) [ 4.558494] usbhid 3-1:1.1: usb_probe_interface [ 4.558497] usbhid 3-1:1.1: usb_probe_interface - got id [ 4.562827] usb 3-1: adding 3-1:1.2 (config #1, interface 2) [ 4.563571] usbhid 3-1:1.2: usb_probe_interface [ 4.563574] usbhid 3-1:1.2: usb_probe_interface - got id [ 4.573730] usbhid 3-1:1.2: looking for a minor, starting at 0 [ 4.575717] logitech-djreceiver 0003:046D:C52B.0005: hiddev0,hidraw2: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.1-1/input2 [ 4.578588] uhci_hcd 0000:00:1d.1: reserve dev 2 ep83-INT, period 2, phase 1, 36 us [ 4.580028] uhci_hcd 0000:00:1d.1: port 2 portsc 0093,00 [ 4.580079] hub 3-0:1.0: port 2, status 0101, change 0001, 12 Mb/s [ 4.583140] input: Logitech Unifying Device. Wireless PID:101b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.2/0003:046D:C52B.0005/input/input4 [ 4.587588] logitech-djdevice 0003:046D:C52B.0006: input,hidraw3: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:101b] on usb-0000:00:1d.1-1:1 [ 4.677344] systemd[1]: systemd 37 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX +SYSVINIT +LIBCRYPTSETUP; fedora) [ 4.684100] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101 [ 4.718628] systemd[1]: /sbin/modprobe failed with error code 1. [ 4.723497] systemd[1]: Set hostname to <mj>. [ 4.787070] usb 3-2: new full-speed USB device number 3 using uhci_hcd [ 5.052378] systemd-readahead-replay[1727]: Bumped block_nr parameter of 259:0 to 16384. This is a temporary hack and should be removed one day. [ 5.095632] mount (1730) used greatest stack depth: 2848 bytes left [ 5.178402] udevd[1738]: starting version 173 [ 5.344772] EXT4-fs (sda1): re-mounted. Opts: (null) [ 5.803553] mtp-probe[2132]: checking bus 2, device 2: "/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-2" [ 5.841199] mtp-probe[2132]: bus: 2, device: 2 was not an MTP device [ 5.899587] cfg80211: Calling CRDA to update world regulatory domain [ 5.909663] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: [ 5.912136] excluding 0xc0000-0xcffff 0xe0000-0xfffff [ 5.936835] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: [ 5.939735] excluding 0xa0000000-0xa0ffffff [ 5.949460] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: [ 5.959422] excluding 0x60000000-0x60ffffff [ 6.088750] cfg80211: World regulatory domain updated: [ 6.090386] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 6.092140] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.093669] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 6.095420] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 6.096974] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.098695] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.102234] ath5k 0000:03:08.0: registered as 'phy0' [ 6.348558] usb 3-2: skipped 7 descriptors after interface [ 6.348564] usb 3-2: skipped 2 descriptors after interface [ 6.348573] usb 3-2: skipped 1 descriptor after endpoint [ 6.348576] usb 3-2: skipped 2 descriptors after interface [ 6.348585] usb 3-2: skipped 1 descriptor after endpoint [ 6.348588] usb 3-2: skipped 1 descriptor after interface [ 6.353924] usb 3-2: default language 0x0409 [ 6.362594] usb 3-2: udev 3, busnum 3, minor = 258 [ 6.362599] usb 3-2: New USB device found, idVendor=046d, idProduct=0a1f [ 6.364285] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 6.365697] usb 3-2: Product: Logitech G930 Headset [ 6.367149] usb 3-2: Manufacturer: Logitech [ 6.372766] usb 3-2: usb_probe_device [ 6.372772] usb 3-2: configuration #1 chosen from 1 choice [ 6.375603] usb 3-2: adding 3-2:1.0 (config #1, interface 0) [ 6.379314] usb 3-2: adding 3-2:1.1 (config #1, interface 1) [ 6.380862] usb 3-2: adding 3-2:1.2 (config #1, interface 2) [ 6.381929] usb 3-2: adding 3-2:1.3 (config #1, interface 3) [ 6.387937] usbhid 3-2:1.3: usb_probe_interface [ 6.387942] usbhid 3-2:1.3: usb_probe_interface - got id [ 6.402143] input: Logitech Logitech G930 Headset as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.3/input/input5 [ 6.403613] uhci_hcd 0000:00:1d.1: reserve dev 3 ep83-INT, period 8, phase 4, 17 us [ 6.404780] usbhid 3-2:1.3: looking for a minor, starting at 0 [ 6.406773] hid-generic 0003:046D:0A1F.0007: input,hiddev0,hidraw4: USB HID v1.01 Device [Logitech Logitech G930 Headset] on usb-0000:00:1d.1-2/input3 [ 6.408620] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 6.435798] mtp-probe[2513]: checking bus 3, device 2: "/sys/devices/pci0000:00/0000:00:1d.1/usb3/3-1" [ 6.439780] mtp-probe[2514]: checking bus 3, device 3: "/sys/devices/pci0000:00/0000:00:1d.1/usb3/3-2" [ 6.443243] mtp-probe[2514]: bus: 3, device: 3 was not an MTP device [ 6.468527] mtp-probe[2513]: bus: 3, device: 2 was not an MTP device [ 6.490511] Adding 6142972k swap on /dev/sda2. Priority:0 extents:1 across:6142972k SS [ 6.523270] snd-usb-audio 3-2:1.0: usb_probe_interface [ 6.523278] snd-usb-audio 3-2:1.0: usb_probe_interface - got id [ 6.552429] usbcore: registered new interface driver snd-usb-audio [ 6.763753] ath: EEPROM regdomain: 0x0 [ 6.763757] ath: EEPROM indicates default country code should be used [ 6.763760] ath: doing EEPROM country->regdmn map search [ 6.763764] ath: country maps to regdmn code: 0x3a [ 6.763766] ath: Country alpha2 being used: US [ 6.763769] ath: Regpair used: 0x3a [ 6.763817] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 6.763820] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 6.763822] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 6.763827] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 6.763829] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 6.763831] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 6.763833] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 6.763836] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 6.763838] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 6.763840] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 6.763842] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 6.763844] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 6.763846] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 6.763848] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 6.763850] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 6.763853] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 6.763855] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 6.763857] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 6.763859] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 6.763861] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 6.763863] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 6.763865] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 6.763867] cfg80211: Disabling freq 2467 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763869] cfg80211: Disabling freq 2472 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763871] cfg80211: Disabling freq 2484 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763873] cfg80211: Disabling freq 5040 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763875] cfg80211: Disabling freq 5060 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763877] cfg80211: Disabling freq 5080 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763879] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 6.763881] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 6.763883] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 6.763885] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 6.763887] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 6.763890] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 6.763891] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 6.763894] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 6.763896] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 6.763898] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 6.763900] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 6.763902] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 6.763904] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 6.763906] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 6.763908] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 6.763911] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 6.763913] cfg80211: Disabling freq 5500 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763914] cfg80211: Disabling freq 5520 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763916] cfg80211: Disabling freq 5540 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763918] cfg80211: Disabling freq 5560 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763920] cfg80211: Disabling freq 5580 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763922] cfg80211: Disabling freq 5600 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763924] cfg80211: Disabling freq 5620 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763926] cfg80211: Disabling freq 5640 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763928] cfg80211: Disabling freq 5660 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763929] cfg80211: Disabling freq 5680 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763931] cfg80211: Disabling freq 5700 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 6.763933] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 6.763936] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 6.763938] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 6.763940] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 6.763942] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 6.763944] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 6.763946] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 6.763948] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 6.763950] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 6.763953] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 6.765948] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 6.765952] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.765954] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 6.765957] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.765959] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 6.765961] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.765963] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 6.765966] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.765968] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 6.765970] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.765973] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 6.765975] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.765977] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 6.765980] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.765982] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 6.765984] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.765986] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 6.765989] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.765991] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 6.765993] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.765995] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 6.765998] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.766000] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule: [ 6.766002] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 6.766005] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule: [ 6.766027] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 6.766030] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule: [ 6.766032] cfg80211: 2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 6.766034] cfg80211: Disabling freq 5040 MHz [ 6.766036] cfg80211: Disabling freq 5060 MHz [ 6.766038] cfg80211: Disabling freq 5080 MHz [ 6.766041] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 6.766043] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.766045] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 6.766048] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.766050] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 6.766052] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.766055] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 6.766057] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.766061] cfg80211: Disabling freq 5260 MHz [ 6.766063] cfg80211: Disabling freq 5280 MHz [ 6.766065] cfg80211: Disabling freq 5300 MHz [ 6.766067] cfg80211: Disabling freq 5320 MHz [ 6.766069] cfg80211: Disabling freq 5500 MHz [ 6.766070] cfg80211: Disabling freq 5520 MHz [ 6.766072] cfg80211: Disabling freq 5540 MHz [ 6.766074] cfg80211: Disabling freq 5560 MHz [ 6.766076] cfg80211: Disabling freq 5580 MHz [ 6.766077] cfg80211: Disabling freq 5600 MHz [ 6.766079] cfg80211: Disabling freq 5620 MHz [ 6.766081] cfg80211: Disabling freq 5640 MHz [ 6.766083] cfg80211: Disabling freq 5660 MHz [ 6.766084] cfg80211: Disabling freq 5680 MHz [ 6.766086] cfg80211: Disabling freq 5700 MHz [ 6.766088] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 6.766091] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.766093] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 6.766095] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.766097] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 6.766100] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.766102] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 6.766104] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.766107] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 6.766109] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.770791] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 6.778210] cfg80211: Calling CRDA for country: US [ 6.780136] ath5k: phy0: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) [ 6.781784] ath5k: phy0: RF5112B multiband radio found (0x36) [ 6.784826] ath5k 0000:03:09.0: registered as 'phy1' [ 6.796812] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 6.796816] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 6.796819] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 6.796821] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 6.796823] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 6.796826] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 6.796828] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 6.796831] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 6.796833] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 6.796835] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 6.796837] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 6.796839] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 6.796842] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 6.796844] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 6.796846] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 6.796848] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 6.796851] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 6.796853] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 6.796855] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 6.796857] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 6.796859] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 6.796862] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 6.796864] cfg80211: Disabling freq 2467 MHz [ 6.796866] cfg80211: Disabling freq 2472 MHz [ 6.796867] cfg80211: Disabling freq 2484 MHz [ 6.796869] cfg80211: Disabling freq 5040 MHz [ 6.796871] cfg80211: Disabling freq 5060 MHz [ 6.796873] cfg80211: Disabling freq 5080 MHz [ 6.796875] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 6.796877] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 6.796879] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 6.796881] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 6.796884] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 6.796886] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 6.796888] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 6.796890] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 6.796893] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 6.796895] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.796897] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 6.796899] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.796902] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 6.796904] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.796906] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 6.796909] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.796911] cfg80211: Updating information on frequency 5500 MHz for a 20 MHz width channel with regulatory rule: [ 6.796913] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.796915] cfg80211: Updating information on frequency 5520 MHz for a 20 MHz width channel with regulatory rule: [ 6.796918] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.796920] cfg80211: Updating information on frequency 5540 MHz for a 20 MHz width channel with regulatory rule: [ 6.796922] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.796925] cfg80211: Updating information on frequency 5560 MHz for a 20 MHz width channel with regulatory rule: [ 6.796927] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.796929] cfg80211: Updating information on frequency 5580 MHz for a 20 MHz width channel with regulatory rule: [ 6.796932] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.796934] cfg80211: Disabling freq 5600 MHz [ 6.796935] cfg80211: Disabling freq 5620 MHz [ 6.796937] cfg80211: Disabling freq 5640 MHz [ 6.796939] cfg80211: Updating information on frequency 5660 MHz for a 20 MHz width channel with regulatory rule: [ 6.796942] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.796944] cfg80211: Updating information on frequency 5680 MHz for a 20 MHz width channel with regulatory rule: [ 6.796946] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.796949] cfg80211: Updating information on frequency 5700 MHz for a 20 MHz width channel with regulatory rule: [ 6.796951] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.796953] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 6.796956] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 6.796958] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 6.796960] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 6.796963] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 6.796965] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 6.796967] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 6.796970] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 6.796972] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 6.796974] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 6.796982] cfg80211: Regulatory domain changed to country: US [ 6.798500] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 6.800033] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 6.801565] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 6.803081] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.804615] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.806123] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.807614] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 7.279105] ath: EEPROM regdomain: 0x0 [ 7.279109] ath: EEPROM indicates default country code should be used [ 7.279111] ath: doing EEPROM country->regdmn map search [ 7.279115] ath: country maps to regdmn code: 0x3a [ 7.279117] ath: Country alpha2 being used: US [ 7.279119] ath: Regpair used: 0x3a [ 7.279126] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 7.279130] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.279133] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 7.279136] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.279139] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 7.279143] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.279146] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 7.279149] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.279152] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 7.279155] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.279158] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 7.279162] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.279164] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 7.279168] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.279171] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 7.279174] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.279177] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 7.279180] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.279183] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 7.279187] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.279190] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 7.279193] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.279196] cfg80211: Disabling freq 2467 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279199] cfg80211: Disabling freq 2472 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279202] cfg80211: Disabling freq 2484 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279204] cfg80211: Disabling freq 5040 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279207] cfg80211: Disabling freq 5060 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279210] cfg80211: Disabling freq 5080 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279213] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 7.279216] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.279219] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 7.279223] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.279226] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 7.279229] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.279232] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 7.279235] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.279238] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 7.279242] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.279244] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 7.279248] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.279251] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 7.279254] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.279257] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 7.279261] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.279264] cfg80211: Disabling freq 5500 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279266] cfg80211: Disabling freq 5520 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279269] cfg80211: Disabling freq 5540 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279272] cfg80211: Disabling freq 5560 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279275] cfg80211: Disabling freq 5580 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279278] cfg80211: Disabling freq 5600 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279280] cfg80211: Disabling freq 5620 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279283] cfg80211: Disabling freq 5640 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279286] cfg80211: Disabling freq 5660 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279289] cfg80211: Disabling freq 5680 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279291] cfg80211: Disabling freq 5700 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.279294] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 7.279298] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.279301] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 7.279304] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.279307] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 7.279311] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.279314] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 7.279317] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.279325] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 7.279327] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.280305] cfg80211: Ignoring regulatory request Set by core since the driver requires its own regulatory domain to be set first [ 7.283418] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 7.289079] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 7.289082] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.289085] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 7.289087] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.289089] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 7.289092] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.289094] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 7.289096] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.289099] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 7.289101] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.289103] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 7.289106] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.289108] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 7.289110] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.289112] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 7.289115] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.289117] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 7.289120] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.289122] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 7.289124] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.289127] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 7.289129] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.289131] cfg80211: Disabling freq 2467 MHz [ 7.289133] cfg80211: Disabling freq 2472 MHz [ 7.289135] cfg80211: Disabling freq 2484 MHz [ 7.289137] cfg80211: Disabling freq 5040 MHz [ 7.289138] cfg80211: Disabling freq 5060 MHz [ 7.289140] cfg80211: Disabling freq 5080 MHz [ 7.289142] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 7.289145] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 7.289147] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 7.289149] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 7.289152] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 7.289154] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 7.289156] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 7.289159] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 7.289161] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 7.289163] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.289166] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 7.289168] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.289170] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 7.289172] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.289175] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 7.289177] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.289179] cfg80211: Updating information on frequency 5500 MHz for a 20 MHz width channel with regulatory rule: [ 7.289182] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.289184] cfg80211: Updating information on frequency 5520 MHz for a 20 MHz width channel with regulatory rule: [ 7.289186] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.289189] cfg80211: Updating information on frequency 5540 MHz for a 20 MHz width channel with regulatory rule: [ 7.289191] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.289193] cfg80211: Updating information on frequency 5560 MHz for a 20 MHz width channel with regulatory rule: [ 7.289196] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.289198] cfg80211: Updating information on frequency 5580 MHz for a 20 MHz width channel with regulatory rule: [ 7.289200] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.289202] cfg80211: Disabling freq 5600 MHz [ 7.289204] cfg80211: Disabling freq 5620 MHz [ 7.289206] cfg80211: Disabling freq 5640 MHz [ 7.289208] cfg80211: Updating information on frequency 5660 MHz for a 20 MHz width channel with regulatory rule: [ 7.289210] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.289213] cfg80211: Updating information on frequency 5680 MHz for a 20 MHz width channel with regulatory rule: [ 7.289215] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.289217] cfg80211: Updating information on frequency 5700 MHz for a 20 MHz width channel with regulatory rule: [ 7.289220] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.289222] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 7.289224] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 7.289227] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 7.289229] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 7.289231] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 7.289234] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 7.289236] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 7.289238] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 7.289240] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 7.289243] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 7.289451] ath5k: phy1: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) [ 7.290952] ath5k: phy1: RF5112B multiband radio found (0x36) [ 7.293400] ath5k 0000:03:0b.0: registered as 'phy2' [ 7.785830] ath: EEPROM regdomain: 0x0 [ 7.785833] ath: EEPROM indicates default country code should be used [ 7.785834] ath: doing EEPROM country->regdmn map search [ 7.785836] ath: country maps to regdmn code: 0x3a [ 7.785838] ath: Country alpha2 being used: US [ 7.785840] ath: Regpair used: 0x3a [ 7.785844] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 7.785846] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.785848] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 7.785851] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.785853] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 7.785855] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.785857] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 7.785859] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.785861] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 7.785863] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.785865] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 7.785868] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.785870] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 7.785872] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.785874] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 7.785876] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.785878] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 7.785881] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.785883] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 7.785885] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.785887] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 7.785889] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 7.785891] cfg80211: Disabling freq 2467 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785893] cfg80211: Disabling freq 2472 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785895] cfg80211: Disabling freq 2484 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785897] cfg80211: Disabling freq 5040 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785899] cfg80211: Disabling freq 5060 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785901] cfg80211: Disabling freq 5080 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785903] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 7.785905] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.785907] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 7.785909] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.785911] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 7.785914] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.785916] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 7.785918] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.785920] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 7.785922] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.785924] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 7.785926] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.785928] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 7.785931] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.785932] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 7.785935] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.785937] cfg80211: Disabling freq 5500 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785939] cfg80211: Disabling freq 5520 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785940] cfg80211: Disabling freq 5540 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785942] cfg80211: Disabling freq 5560 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785944] cfg80211: Disabling freq 5580 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785946] cfg80211: Disabling freq 5600 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785948] cfg80211: Disabling freq 5620 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785950] cfg80211: Disabling freq 5640 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785952] cfg80211: Disabling freq 5660 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785953] cfg80211: Disabling freq 5680 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785955] cfg80211: Disabling freq 5700 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 7.785957] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 7.785959] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.785961] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 7.785964] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.785966] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 7.785968] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.785970] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 7.785972] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.785974] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 7.785976] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 7.786932] cfg80211: Ignoring regulatory request Set by core since the driver requires its own regulatory domain to be set first [ 7.790142] ieee80211 phy2: Selected rate control algorithm 'minstrel_ht' [ 7.795888] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 7.795891] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.795894] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 7.795896] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.795899] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 7.795901] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.795903] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 7.795905] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.795908] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 7.795910] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.795912] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 7.795915] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.795917] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 7.795919] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.795921] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 7.795923] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.795926] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 7.795928] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.795930] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 7.795933] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.795935] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 7.795937] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.795939] cfg80211: Disabling freq 2467 MHz [ 7.795941] cfg80211: Disabling freq 2472 MHz [ 7.795943] cfg80211: Disabling freq 2484 MHz [ 7.795944] cfg80211: Disabling freq 5040 MHz [ 7.795946] cfg80211: Disabling freq 5060 MHz [ 7.795948] cfg80211: Disabling freq 5080 MHz [ 7.795950] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 7.795952] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 7.795955] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 7.795957] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 7.795959] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 7.795962] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 7.795964] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 7.795966] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 7.795968] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 7.795971] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.795973] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 7.795975] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.795978] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 7.795980] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.795982] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 7.795985] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.795987] cfg80211: Updating information on frequency 5500 MHz for a 20 MHz width channel with regulatory rule: [ 7.795989] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.795991] cfg80211: Updating information on frequency 5520 MHz for a 20 MHz width channel with regulatory rule: [ 7.795994] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.795996] cfg80211: Updating information on frequency 5540 MHz for a 20 MHz width channel with regulatory rule: [ 7.795998] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.796001] cfg80211: Updating information on frequency 5560 MHz for a 20 MHz width channel with regulatory rule: [ 7.796003] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.796005] cfg80211: Updating information on frequency 5580 MHz for a 20 MHz width channel with regulatory rule: [ 7.796008] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.796019] cfg80211: Disabling freq 5600 MHz [ 7.796021] cfg80211: Disabling freq 5620 MHz [ 7.796022] cfg80211: Disabling freq 5640 MHz [ 7.796025] cfg80211: Updating information on frequency 5660 MHz for a 20 MHz width channel with regulatory rule: [ 7.796027] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.796032] cfg80211: Updating information on frequency 5680 MHz for a 20 MHz width channel with regulatory rule: [ 7.796035] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.796037] cfg80211: Updating information on frequency 5700 MHz for a 20 MHz width channel with regulatory rule: [ 7.796040] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.796042] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 7.796045] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 7.796047] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 7.796049] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 7.796051] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 7.796054] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 7.796056] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 7.796058] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 7.796061] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 7.796063] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 7.796264] ath5k: phy2: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) [ 7.797825] ath5k: phy2: RF5112B multiband radio found (0x36) [ 7.799820] ath5k 0000:04:00.0: enabling device (0000 -> 0002) [ 7.801717] ath5k 0000:04:00.0: registered as 'phy3' [ 8.270386] ath: EEPROM regdomain: 0x13 [ 8.270389] ath: EEPROM indicates we should expect a direct regpair map [ 8.270393] ath: Country alpha2 being used: 00 [ 8.270395] ath: Regpair used: 0x13 [ 8.270406] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 8.270408] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 8.270410] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 8.270413] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 8.270415] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 8.270417] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 8.270419] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 8.270421] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 8.270423] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 8.270426] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 8.270428] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 8.270430] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 8.270432] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 8.270434] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 8.270436] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 8.270439] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 8.270441] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 8.270443] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 8.270445] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 8.270447] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 8.270449] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 8.270451] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm) [ 8.270453] cfg80211: Disabling freq 2467 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270455] cfg80211: Disabling freq 2472 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270457] cfg80211: Disabling freq 2484 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270459] cfg80211: Disabling freq 5040 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270461] cfg80211: Disabling freq 5060 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270463] cfg80211: Disabling freq 5080 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270465] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 8.270467] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 8.270469] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 8.270471] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 8.270473] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 8.270476] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 8.270478] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 8.270480] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 8.270482] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 8.270484] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 8.270486] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 8.270489] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 8.270491] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 8.270493] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 8.270495] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 8.270497] cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 8.270499] cfg80211: Disabling freq 5500 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270501] cfg80211: Disabling freq 5520 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270503] cfg80211: Disabling freq 5540 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270505] cfg80211: Disabling freq 5560 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270507] cfg80211: Disabling freq 5580 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270508] cfg80211: Disabling freq 5600 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270510] cfg80211: Disabling freq 5620 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270512] cfg80211: Disabling freq 5640 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270514] cfg80211: Disabling freq 5660 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270516] cfg80211: Disabling freq 5680 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270518] cfg80211: Disabling freq 5700 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 8.270520] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 8.270522] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 8.270524] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 8.270526] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 8.270528] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 8.270530] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 8.270532] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 8.270535] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 8.270537] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 8.270539] cfg80211: 5715000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm) [ 8.271526] cfg80211: Ignoring regulatory request Set by core since the driver requires its own regulatory domain to be set first [ 8.274639] ieee80211 phy3: Selected rate control algorithm 'minstrel_ht' [ 8.280624] cfg80211: Calling CRDA to update world regulatory domain [ 8.282397] ath5k: phy3: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) [ 8.284057] ath5k: phy3: RF5112B multiband radio found (0x36) [ 8.300536] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 8.300541] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300543] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 8.300546] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300548] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 8.300551] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300553] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 8.300555] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300558] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 8.300560] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300562] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 8.300565] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300567] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 8.300569] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300572] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 8.300574] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300576] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 8.300579] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300581] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 8.300584] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300586] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 8.300588] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300590] cfg80211: Disabling freq 2467 MHz [ 8.300592] cfg80211: Disabling freq 2472 MHz [ 8.300594] cfg80211: Disabling freq 2484 MHz [ 8.300596] cfg80211: Disabling freq 5040 MHz [ 8.300598] cfg80211: Disabling freq 5060 MHz [ 8.300599] cfg80211: Disabling freq 5080 MHz [ 8.300601] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 8.300604] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.300606] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 8.300609] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.300611] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 8.300613] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.300616] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 8.300618] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.300620] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 8.300623] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300625] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 8.300627] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300630] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 8.300632] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300634] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 8.300637] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300639] cfg80211: Updating information on frequency 5500 MHz for a 20 MHz width channel with regulatory rule: [ 8.300641] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300644] cfg80211: Updating information on frequency 5520 MHz for a 20 MHz width channel with regulatory rule: [ 8.300646] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300648] cfg80211: Updating information on frequency 5540 MHz for a 20 MHz width channel with regulatory rule: [ 8.300651] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300653] cfg80211: Updating information on frequency 5560 MHz for a 20 MHz width channel with regulatory rule: [ 8.300656] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300658] cfg80211: Updating information on frequency 5580 MHz for a 20 MHz width channel with regulatory rule: [ 8.300660] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300662] cfg80211: Disabling freq 5600 MHz [ 8.300664] cfg80211: Disabling freq 5620 MHz [ 8.300666] cfg80211: Disabling freq 5640 MHz [ 8.300668] cfg80211: Updating information on frequency 5660 MHz for a 20 MHz width channel with regulatory rule: [ 8.300670] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300673] cfg80211: Updating information on frequency 5680 MHz for a 20 MHz width channel with regulatory rule: [ 8.300675] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300677] cfg80211: Updating information on frequency 5700 MHz for a 20 MHz width channel with regulatory rule: [ 8.300680] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300682] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 8.300684] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.300687] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 8.300689] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.300691] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 8.300694] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.300696] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 8.300698] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.300701] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 8.300703] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.300712] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 8.300714] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300717] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 8.300719] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300721] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 8.300724] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300726] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 8.300728] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300731] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 8.300733] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300735] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 8.300738] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300740] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 8.300742] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300745] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 8.300747] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300749] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 8.300752] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300754] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 8.300757] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300759] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 8.300761] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300763] cfg80211: Disabling freq 2467 MHz [ 8.300765] cfg80211: Disabling freq 2472 MHz [ 8.300767] cfg80211: Disabling freq 2484 MHz [ 8.300769] cfg80211: Disabling freq 5040 MHz [ 8.300771] cfg80211: Disabling freq 5060 MHz [ 8.300772] cfg80211: Disabling freq 5080 MHz [ 8.300774] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 8.300777] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.300779] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 8.300781] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.300784] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 8.300786] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.300788] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 8.300791] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.300793] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 8.300795] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300798] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 8.300800] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300802] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 8.300805] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300807] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 8.300809] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300812] cfg80211: Updating information on frequency 5500 MHz for a 20 MHz width channel with regulatory rule: [ 8.300814] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300816] cfg80211: Updating information on frequency 5520 MHz for a 20 MHz width channel with regulatory rule: [ 8.300819] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300821] cfg80211: Updating information on frequency 5540 MHz for a 20 MHz width channel with regulatory rule: [ 8.300823] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300826] cfg80211: Updating information on frequency 5560 MHz for a 20 MHz width channel with regulatory rule: [ 8.300828] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300830] cfg80211: Updating information on frequency 5580 MHz for a 20 MHz width channel with regulatory rule: [ 8.300832] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300835] cfg80211: Disabling freq 5600 MHz [ 8.300836] cfg80211: Disabling freq 5620 MHz [ 8.300838] cfg80211: Disabling freq 5640 MHz [ 8.300840] cfg80211: Updating information on frequency 5660 MHz for a 20 MHz width channel with regulatory rule: [ 8.300843] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300845] cfg80211: Updating information on frequency 5680 MHz for a 20 MHz width channel with regulatory rule: [ 8.300848] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300850] cfg80211: Updating information on frequency 5700 MHz for a 20 MHz width channel with regulatory rule: [ 8.300852] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300855] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 8.300857] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.300859] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 8.300862] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.300864] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 8.300866] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.300869] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 8.300871] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.300873] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 8.300876] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.300884] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 8.300886] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300889] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 8.300891] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300893] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 8.300896] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300898] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 8.300900] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300902] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 8.300905] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300907] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 8.300909] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300912] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 8.300914] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300917] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 8.300919] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300921] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 8.300924] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300926] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 8.300928] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300931] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 8.300933] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.300935] cfg80211: Disabling freq 2467 MHz [ 8.300937] cfg80211: Disabling freq 2472 MHz [ 8.300939] cfg80211: Disabling freq 2484 MHz [ 8.300941] cfg80211: Disabling freq 5040 MHz [ 8.300942] cfg80211: Disabling freq 5060 MHz [ 8.300944] cfg80211: Disabling freq 5080 MHz [ 8.300946] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 8.300949] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.300951] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 8.300953] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.300956] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 8.300958] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.300960] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 8.300963] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.300965] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 8.300967] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300970] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 8.300972] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300975] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 8.300977] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300979] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 8.300982] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300984] cfg80211: Updating information on frequency 5500 MHz for a 20 MHz width channel with regulatory rule: [ 8.300986] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300988] cfg80211: Updating information on frequency 5520 MHz for a 20 MHz width channel with regulatory rule: [ 8.300991] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300993] cfg80211: Updating information on frequency 5540 MHz for a 20 MHz width channel with regulatory rule: [ 8.300995] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.300998] cfg80211: Updating information on frequency 5560 MHz for a 20 MHz width channel with regulatory rule: [ 8.301012] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301015] cfg80211: Updating information on frequency 5580 MHz for a 20 MHz width channel with regulatory rule: [ 8.301017] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301019] cfg80211: Disabling freq 5600 MHz [ 8.301021] cfg80211: Disabling freq 5620 MHz [ 8.301023] cfg80211: Disabling freq 5640 MHz [ 8.301025] cfg80211: Updating information on frequency 5660 MHz for a 20 MHz width channel with regulatory rule: [ 8.301027] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301030] cfg80211: Updating information on frequency 5680 MHz for a 20 MHz width channel with regulatory rule: [ 8.301032] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301034] cfg80211: Updating information on frequency 5700 MHz for a 20 MHz width channel with regulatory rule: [ 8.301036] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301039] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 8.301041] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.301043] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 8.301046] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.301048] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 8.301050] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.301053] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 8.301055] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.301057] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 8.301060] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.301067] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 8.301070] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.301072] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 8.301074] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.301076] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 8.301079] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.301081] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 8.301083] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.301086] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 8.301088] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.301090] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 8.301093] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.301095] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 8.301098] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.301100] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 8.301102] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.301104] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 8.301107] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.301109] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 8.301111] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.301114] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 8.301116] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.301118] cfg80211: Disabling freq 2467 MHz [ 8.301120] cfg80211: Disabling freq 2472 MHz [ 8.301121] cfg80211: Disabling freq 2484 MHz [ 8.301123] cfg80211: Disabling freq 5040 MHz [ 8.301125] cfg80211: Disabling freq 5060 MHz [ 8.301127] cfg80211: Disabling freq 5080 MHz [ 8.301129] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 8.301131] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.301134] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 8.301136] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.301138] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 8.301141] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.301143] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 8.301145] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.301147] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 8.301150] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301152] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 8.301154] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301157] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 8.301159] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301161] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 8.301164] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301166] cfg80211: Updating information on frequency 5500 MHz for a 20 MHz width channel with regulatory rule: [ 8.301168] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301171] cfg80211: Updating information on frequency 5520 MHz for a 20 MHz width channel with regulatory rule: [ 8.301173] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301175] cfg80211: Updating information on frequency 5540 MHz for a 20 MHz width channel with regulatory rule: [ 8.301178] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301180] cfg80211: Updating information on frequency 5560 MHz for a 20 MHz width channel with regulatory rule: [ 8.301182] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301184] cfg80211: Updating information on frequency 5580 MHz for a 20 MHz width channel with regulatory rule: [ 8.301187] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301189] cfg80211: Disabling freq 5600 MHz [ 8.301191] cfg80211: Disabling freq 5620 MHz [ 8.301192] cfg80211: Disabling freq 5640 MHz [ 8.301195] cfg80211: Updating information on frequency 5660 MHz for a 20 MHz width channel with regulatory rule: [ 8.301197] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301199] cfg80211: Updating information on frequency 5680 MHz for a 20 MHz width channel with regulatory rule: [ 8.301202] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301204] cfg80211: Updating information on frequency 5700 MHz for a 20 MHz width channel with regulatory rule: [ 8.301206] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.301209] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 8.301211] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.301214] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 8.301216] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.301218] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 8.301221] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.301223] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 8.301225] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.301228] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 8.301230] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.301236] cfg80211: World regulatory domain updated: [ 8.302994] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 8.304754] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.306534] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 8.308319] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 8.310088] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.311831] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.365377] cfg80211: Calling CRDA for country: US [ 8.372990] cfg80211: Pending regulatory request, waiting for it to be processed... [ 8.390242] cfg80211: Pending regulatory request, waiting for it to be processed... [ 8.394645] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 8.394650] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394652] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 8.394655] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394657] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 8.394659] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394662] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 8.394664] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394666] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 8.394668] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394671] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 8.394673] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394675] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 8.394678] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394680] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 8.394682] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394684] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 8.394687] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394689] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 8.394691] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394693] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 8.394696] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394698] cfg80211: Disabling freq 2467 MHz [ 8.394700] cfg80211: Disabling freq 2472 MHz [ 8.394701] cfg80211: Disabling freq 2484 MHz [ 8.394703] cfg80211: Disabling freq 5040 MHz [ 8.394705] cfg80211: Disabling freq 5060 MHz [ 8.394707] cfg80211: Disabling freq 5080 MHz [ 8.394709] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 8.394711] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.394713] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 8.394716] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.394718] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 8.394720] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.394722] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 8.394725] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.394727] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 8.394729] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394731] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 8.394733] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394736] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 8.394738] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394740] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 8.394742] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394745] cfg80211: Updating information on frequency 5500 MHz for a 20 MHz width channel with regulatory rule: [ 8.394747] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394749] cfg80211: Updating information on frequency 5520 MHz for a 20 MHz width channel with regulatory rule: [ 8.394751] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394754] cfg80211: Updating information on frequency 5540 MHz for a 20 MHz width channel with regulatory rule: [ 8.394756] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394758] cfg80211: Updating information on frequency 5560 MHz for a 20 MHz width channel with regulatory rule: [ 8.394760] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394763] cfg80211: Updating information on frequency 5580 MHz for a 20 MHz width channel with regulatory rule: [ 8.394765] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394767] cfg80211: Disabling freq 5600 MHz [ 8.394769] cfg80211: Disabling freq 5620 MHz [ 8.394770] cfg80211: Disabling freq 5640 MHz [ 8.394772] cfg80211: Updating information on frequency 5660 MHz for a 20 MHz width channel with regulatory rule: [ 8.394775] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394777] cfg80211: Updating information on frequency 5680 MHz for a 20 MHz width channel with regulatory rule: [ 8.394779] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394782] cfg80211: Updating information on frequency 5700 MHz for a 20 MHz width channel with regulatory rule: [ 8.394784] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394786] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 8.394788] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.394791] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 8.394793] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.394795] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 8.394798] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.394800] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 8.394802] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.394804] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 8.394807] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.394816] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 8.394818] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394820] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 8.394823] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394825] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 8.394827] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394829] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 8.394832] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394834] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 8.394836] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394838] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 8.394841] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394843] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 8.394845] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394847] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 8.394850] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394852] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 8.394855] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394857] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 8.394859] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394861] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 8.394864] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394866] cfg80211: Disabling freq 2467 MHz [ 8.394867] cfg80211: Disabling freq 2472 MHz [ 8.394869] cfg80211: Disabling freq 2484 MHz [ 8.394871] cfg80211: Disabling freq 5040 MHz [ 8.394872] cfg80211: Disabling freq 5060 MHz [ 8.394874] cfg80211: Disabling freq 5080 MHz [ 8.394876] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 8.394878] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.394880] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 8.394883] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.394885] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 8.394887] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.394889] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 8.394892] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.394894] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 8.394896] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394899] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 8.394901] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394903] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 8.394905] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394908] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 8.394910] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394912] cfg80211: Updating information on frequency 5500 MHz for a 20 MHz width channel with regulatory rule: [ 8.394914] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394917] cfg80211: Updating information on frequency 5520 MHz for a 20 MHz width channel with regulatory rule: [ 8.394919] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394921] cfg80211: Updating information on frequency 5540 MHz for a 20 MHz width channel with regulatory rule: [ 8.394923] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394926] cfg80211: Updating information on frequency 5560 MHz for a 20 MHz width channel with regulatory rule: [ 8.394928] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394930] cfg80211: Updating information on frequency 5580 MHz for a 20 MHz width channel with regulatory rule: [ 8.394933] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394935] cfg80211: Disabling freq 5600 MHz [ 8.394936] cfg80211: Disabling freq 5620 MHz [ 8.394938] cfg80211: Disabling freq 5640 MHz [ 8.394940] cfg80211: Updating information on frequency 5660 MHz for a 20 MHz width channel with regulatory rule: [ 8.394942] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394945] cfg80211: Updating information on frequency 5680 MHz for a 20 MHz width channel with regulatory rule: [ 8.394947] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394949] cfg80211: Updating information on frequency 5700 MHz for a 20 MHz width channel with regulatory rule: [ 8.394951] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.394954] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 8.394956] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.394958] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 8.394960] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.394963] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 8.394965] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.394967] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 8.394969] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.394972] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 8.394974] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.394981] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 8.394983] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394986] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 8.394988] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394990] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 8.394992] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.394995] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 8.394997] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395532] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 8.395534] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395537] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 8.395539] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395541] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 8.395544] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395546] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 8.395548] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395550] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 8.395552] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395554] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 8.395557] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395559] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 8.395561] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395563] cfg80211: Disabling freq 2467 MHz [ 8.395565] cfg80211: Disabling freq 2472 MHz [ 8.395567] cfg80211: Disabling freq 2484 MHz [ 8.395568] cfg80211: Disabling freq 5040 MHz [ 8.395570] cfg80211: Disabling freq 5060 MHz [ 8.395571] cfg80211: Disabling freq 5080 MHz [ 8.395574] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 8.395576] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.395578] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 8.395580] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.395582] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 8.395585] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.395587] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 8.395589] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.395591] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 8.395594] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395596] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 8.395598] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395600] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 8.395602] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395605] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 8.395607] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395609] cfg80211: Updating information on frequency 5500 MHz for a 20 MHz width channel with regulatory rule: [ 8.395611] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395614] cfg80211: Updating information on frequency 5520 MHz for a 20 MHz width channel with regulatory rule: [ 8.395616] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395618] cfg80211: Updating information on frequency 5540 MHz for a 20 MHz width channel with regulatory rule: [ 8.395620] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395622] cfg80211: Updating information on frequency 5560 MHz for a 20 MHz width channel with regulatory rule: [ 8.395625] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395627] cfg80211: Updating information on frequency 5580 MHz for a 20 MHz width channel with regulatory rule: [ 8.395629] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395631] cfg80211: Disabling freq 5600 MHz [ 8.395633] cfg80211: Disabling freq 5620 MHz [ 8.395634] cfg80211: Disabling freq 5640 MHz [ 8.395636] cfg80211: Updating information on frequency 5660 MHz for a 20 MHz width channel with regulatory rule: [ 8.395639] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395641] cfg80211: Updating information on frequency 5680 MHz for a 20 MHz width channel with regulatory rule: [ 8.395643] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395645] cfg80211: Updating information on frequency 5700 MHz for a 20 MHz width channel with regulatory rule: [ 8.395648] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395650] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 8.395652] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.395654] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 8.395657] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.395659] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 8.395661] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.395663] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 8.395666] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.395668] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 8.395670] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.395677] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 8.395679] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395682] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 8.395684] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395686] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 8.395688] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395690] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 8.395693] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395695] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 8.395697] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395699] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 8.395702] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395704] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 8.395706] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395708] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 8.395710] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395713] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 8.395715] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395717] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 8.395719] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395721] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 8.395724] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.395726] cfg80211: Disabling freq 2467 MHz [ 8.395727] cfg80211: Disabling freq 2472 MHz [ 8.395729] cfg80211: Disabling freq 2484 MHz [ 8.395731] cfg80211: Disabling freq 5040 MHz [ 8.395732] cfg80211: Disabling freq 5060 MHz [ 8.395734] cfg80211: Disabling freq 5080 MHz [ 8.395736] cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule: [ 8.395738] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.395740] cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule: [ 8.395743] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.395745] cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule: [ 8.395747] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.395749] cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule: [ 8.395752] cfg80211: 5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.395754] cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule: [ 8.395756] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395758] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule: [ 8.395761] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395763] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule: [ 8.395765] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395767] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule: [ 8.395770] cfg80211: 5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395772] cfg80211: Updating information on frequency 5500 MHz for a 20 MHz width channel with regulatory rule: [ 8.395774] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395776] cfg80211: Updating information on frequency 5520 MHz for a 20 MHz width channel with regulatory rule: [ 8.395779] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395781] cfg80211: Updating information on frequency 5540 MHz for a 20 MHz width channel with regulatory rule: [ 8.395783] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395785] cfg80211: Updating information on frequency 5560 MHz for a 20 MHz width channel with regulatory rule: [ 8.395788] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395790] cfg80211: Updating information on frequency 5580 MHz for a 20 MHz width channel with regulatory rule: [ 8.395792] cfg80211: 5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395794] cfg80211: Disabling freq 5600 MHz [ 8.395796] cfg80211: Disabling freq 5620 MHz [ 8.395797] cfg80211: Disabling freq 5640 MHz [ 8.395799] cfg80211: Updating information on frequency 5660 MHz for a 20 MHz width channel with regulatory rule: [ 8.395802] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395804] cfg80211: Updating information on frequency 5680 MHz for a 20 MHz width channel with regulatory rule: [ 8.395806] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395808] cfg80211: Updating information on frequency 5700 MHz for a 20 MHz width channel with regulatory rule: [ 8.395811] cfg80211: 5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.395813] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule: [ 8.395815] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.395817] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule: [ 8.395820] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.395822] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule: [ 8.395824] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.395826] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule: [ 8.395828] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.395831] cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule: [ 8.395833] cfg80211: 5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.395839] cfg80211: Regulatory domain changed to country: US [ 8.397583] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 8.399216] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.400807] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.402414] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.403990] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.405567] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.407126] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.619245] fedora-storage-init[2673]: Setting up Logical Volume Management: /dev/mapper/control: open failed: No such device [ 8.621214] fedora-storage-init[2673]: Failure to communicate with kernel device-mapper driver. [ 8.622956] fedora-storage-init[2673]: Check that device-mapper is available in the kernel. [ 8.641097] fedora-storage-init[2673]: No volume groups found [ 8.643207] fedora-storage-init[2673]: [ OK ] [ 8.722856] fedora-storage-init[2681]: Setting up Logical Volume Management: /dev/mapper/control: open failed: No such device [ 8.724545] fedora-storage-init[2681]: Failure to communicate with kernel device-mapper driver. [ 8.726175] fedora-storage-init[2681]: Check that device-mapper is available in the kernel. [ 8.740727] fedora-storage-init[2681]: No volume groups found [ 8.742426] fedora-storage-init[2681]: [ OK ] [ 8.785887] lvm[2689]: /dev/mapper/control: open failed: No such device [ 8.787878] lvm[2689]: Failure to communicate with kernel device-mapper driver. [ 8.789456] lvm[2689]: Check that device-mapper is available in the kernel. [ 8.804681] lvm[2689]: No volume groups found [ 9.094668] iptables.init[2704]: iptables: Applying firewall rules: FATAL: Module ip_tables not found. [ 9.096325] iptables.init[2704]: iptables-restore v1.4.12: iptables-restore: unable to initialize table 'filter' [ 9.098040] iptables.init[2704]: Error occurred at line: 3 [ 9.099689] iptables.init[2704]: Try `iptables-restore -h' or 'iptables-restore --help' for more information. [ 9.104510] iptables.init[2704]: [FAILED] [ 9.111866] /usr/sbin/crond[2727]: (CRON) INFO (Syslog will be used instead of sendmail.): No such file or directory [ 9.114513] /usr/sbin/crond[2727]: (CRON) INFO (running with inotify support) [ 9.174587] acpid[2739]: starting up with netlink and the input layer [ 9.175182] acpid[2739]: skipping incomplete file /etc/acpi/events/videoconf [ 9.175322] acpid[2739]: 1 rule loaded [ 9.175586] acpid[2739]: waiting for events: event logging is off [ 9.213691] abrtd[2740]: Init complete, entering main loop [ 9.274609] /usr/sbin/gpm[2749]: *** info [daemon/startup.c(136)]: [ 9.276372] /usr/sbin/gpm[2749]: Started gpm successfully. Entered daemon mode. [ 9.351750] ntpd[2755]: ntpd [email protected] Thu Oct 6 15:37:57 UTC 2011 (1) [ 9.356472] ntpd[2755]: proto: precision = 0.078 usec [ 9.356627] ntpd[2755]: 0.0.0.0 c01d 0d kern kernel time sync enabled [ 9.357041] ntpd[2755]: ntp_io: estimated max descriptors: 1024, initial socket boundary: 16 [ 9.357713] ntpd[2755]: Listen and drop on 0 v4wildcard 0.0.0.0 UDP 123 [ 9.358062] ntpd[2755]: Listen normally on 1 lo 127.0.0.1 UDP 123 [ 9.358179] ntpd[2755]: peers refreshed [ 9.358314] ntpd[2755]: Listening on routing socket on fd #18 for interface updates [ 9.360341] ntpd[2755]: restrict: error in address '::' on line 10. Ignoring... [ 9.361300] ntpd[2755]: restrict: error in address '::1' on line 16. Ignoring... [ 9.363642] ntpd[2755]: Deferring DNS for 0.fedora.pool.ntp.org 1 [ 9.364292] ntpd[2755]: Deferring DNS for 1.fedora.pool.ntp.org 1 [ 9.364866] ntpd[2755]: Deferring DNS for 2.fedora.pool.ntp.org 1 [ 9.365435] ntpd[2755]: Deferring DNS for 3.fedora.pool.ntp.org 1 [ 9.366942] ntpd[2755]: 0.0.0.0 c016 06 restart [ 9.367057] ntpd[2755]: 0.0.0.0 c012 02 freq_set kernel 6.427 PPM [ 9.367282] ntpd[2761]: signal_no_reset: signal 17 had flags 4000000 [ 9.440664] avahi-daemon[2763]: Found user 'avahi' (UID 70) and group 'avahi' (GID 70). [ 9.442307] avahi-daemon[2763]: Successfully dropped root privileges. [ 9.443888] avahi-daemon[2763]: avahi-daemon 0.6.30 starting up. [ 9.577053] tcsd[2764]: insmod: can't read '/lib/modules/3.7.0-rc1-main/kernel/drivers/char/tpm/tpm_*': No such file or directory [ 9.580122] systemd[1]: iptables.service: main process exited, code=exited, status=1 [ 9.584823] tcsd[2777]: TCSD TDDL[2777]: TrouSerS ERROR: Could not find a device to open! [ 9.593458] tcsd[2764]: Starting tcsd: [FAILED] [ 9.595759] systemd[1]: Unit iptables.service entered failed state. [ 9.694559] systemd[1]: tcsd.service: control process exited, code=exited status=137 [ 9.716901] systemd[1]: Unit tcsd.service entered failed state. [ 9.826090] dbus-daemon[2789]: dbus[2789]: [system] Activating systemd to hand-off: service name='org.freedesktop.NetworkManager' unit='dbus-org.freedesktop.NetworkManager.service' [ 9.828863] dbus[2789]: [system] Activating systemd to hand-off: service name='org.freedesktop.NetworkManager' unit='dbus-org.freedesktop.NetworkManager.service' [ 9.838390] avahi-daemon[2763]: Successfully called chroot(). [ 9.838428] avahi-daemon[2763]: Successfully dropped remaining capabilities. [ 9.838464] avahi-daemon[2763]: Loading service file /services/ssh.service. [ 9.838499] avahi-daemon[2763]: Loading service file /services/udisks.service. [ 9.838536] avahi-daemon[2763]: Network interface enumeration completed. [ 9.838571] avahi-daemon[2763]: Registering HINFO record with values 'X86_64'/'LINUX'. [ 9.838606] avahi-daemon[2763]: Server startup complete. Host name is mj.local. Local service cookie is 2095606922. [ 9.838644] dbus[2789]: [system] Successfully activated service 'org.freedesktop.systemd1' [ 9.838684] dbus-daemon[2789]: dbus[2789]: [system] Successfully activated service 'org.freedesktop.systemd1' [ 9.838721] avahi-daemon[2763]: Service "mj" (/services/udisks.service) successfully established. [ 9.838755] avahi-daemon[2763]: Service "mj" (/services/ssh.service) successfully established. [ 10.377215] r8169 0000:01:00.0 p32p1: link down [ 10.377364] r8169 0000:01:00.0 p32p1: link down [ 12.126367] r8169 0000:01:00.0 p32p1: link up [ 15.429052] uhci_hcd 0000:00:1d.1: reserve dev 3 ep01-ISO, period 1, phase 0, 233 us [ 15.454552] uhci_hcd 0000:00:1d.1: release dev 3 ep01-ISO, period 1, phase 0, 233 us [ 15.584919] uhci_hcd 0000:00:1d.1: reserve dev 3 ep01-ISO, period 1, phase 0, 233 us [ 15.611549] uhci_hcd 0000:00:1d.1: release dev 3 ep01-ISO, period 1, phase 0, 233 us [ 15.676911] uhci_hcd 0000:00:1d.1: reserve dev 3 ep01-ISO, period 1, phase 0, 233 us [ 15.708822] uhci_hcd 0000:00:1d.1: reserve dev 3 ep82-ISO, period 1, phase 0, 34 us [ 20.720620] uhci_hcd 0000:00:1d.1: release dev 3 ep82-ISO, period 1, phase 0, 34 us [ 20.724611] uhci_hcd 0000:00:1d.1: release dev 3 ep01-ISO, period 1, phase 0, 233 us [ 31.480084] CPA self-test: [ 31.498000] 4k 1046528 large 0 gb 0 x 262491[ffff880000000000-ffff8800cf7ff000] miss 198656 [ 31.516722] 4k 1046528 large 0 gb 0 x 262491[ffff880000000000-ffff8800cf7ff000] miss 198656 [ 31.534920] 4k 1046528 large 0 gb 0 x 262491[ffff880000000000-ffff8800cf7ff000] miss 198656 [ 31.534924] ok. [ 86.984503] uhci_hcd 0000:00:1d.1: reserve dev 3 ep01-ISO, period 1, phase 0, 233 us [ 87.014040] uhci_hcd 0000:00:1d.1: release dev 3 ep01-ISO, period 1, phase 0, 233 us [ 87.165729] uhci_hcd 0000:00:1d.1: reserve dev 3 ep01-ISO, period 1, phase 0, 233 us [ 87.204073] uhci_hcd 0000:00:1d.1: release dev 3 ep01-ISO, period 1, phase 0, 233 us [ 87.286432] uhci_hcd 0000:00:1d.1: reserve dev 3 ep01-ISO, period 1, phase 0, 233 us [ 92.731108] uhci_hcd 0000:00:1d.1: release dev 3 ep01-ISO, period 1, phase 0, 233 us [ 162.549018] git (3709) used greatest stack depth: 2736 bytes left [ 164.650528] tty_init_dev: 27 callbacks suppressed [ 241.482118] INFO: task gnome-settings-:3155 blocked for more than 120 seconds. [ 241.483499] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 241.484888] gnome-settings- D 0000000000000000 6136 3155 1 0x00000000 [ 241.486265] ffff8801298afcc8 0000000000000046 ffff88012993b420 0000000000000246 [ 241.487652] ffff8801298affd8 ffff8801298affd8 ffff8801298affd8 ffff8801298affd8 [ 241.489035] ffff88012993a2c0 ffff88012993b420 ffff880128cb0b80 ffff88012993b420 [ 241.490421] Call Trace: [ 241.491765] [<ffffffff815d8064>] schedule+0x24/0x70 [ 241.493116] [<ffffffff81043945>] exit_mm+0x85/0x120 [ 241.494467] [<ffffffff8104628f>] do_exit+0x13f/0x580 [ 241.495784] [<ffffffff81046957>] do_group_exit+0x47/0xb0 [ 241.497090] [<ffffffff810597ef>] get_signal_to_deliver+0x21f/0x580 [ 241.498384] [<ffffffff81002014>] do_signal+0x24/0x120 [ 241.499673] [<ffffffff815da28c>] ? sysret_signal+0x5/0x47 [ 241.500964] [<ffffffff81002195>] do_notify_resume+0x65/0xa0 [ 241.502239] [<ffffffff8129342e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [ 241.503525] [<ffffffff815da51a>] int_signal+0x12/0x17 [ 241.504813] no locks held by gnome-settings-/3155. [ 241.506095] INFO: task gnome-settings-:3156 blocked for more than 120 seconds. [ 241.507405] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 241.508721] gnome-settings- D 00000000ffffffff 5104 3156 1 0x00000000 [ 241.510056] ffff88011c80bcc8 0000000000000046 ffff88011c80bc78 ffffffff8109ad9d [ 241.511414] ffff88011c80bfd8 ffff88011c80bfd8 ffff88011c80bfd8 ffff88011c80bfd8 [ 241.512780] ffff8801279fd6e0 ffff88012993a2c0 ffff880129809d28 ffff88012993a2c0 [ 241.514134] Call Trace: [ 241.515480] [<ffffffff8109ad9d>] ? trace_hardirqs_on_caller+0x7d/0x120 [ 241.516857] [<ffffffff815d8064>] schedule+0x24/0x70 [ 241.518219] [<ffffffff81043945>] exit_mm+0x85/0x120 [ 241.519592] [<ffffffff8104628f>] do_exit+0x13f/0x580 [ 241.520952] [<ffffffff81046957>] do_group_exit+0x47/0xb0 [ 241.522315] [<ffffffff810597ef>] get_signal_to_deliver+0x21f/0x580 [ 241.523687] [<ffffffff81002014>] do_signal+0x24/0x120 [ 241.525066] [<ffffffff8109b8a4>] ? __lock_is_held+0x54/0x70 [ 241.526436] [<ffffffff815da28c>] ? sysret_signal+0x5/0x47 [ 241.527841] [<ffffffff81002195>] do_notify_resume+0x65/0xa0 [ 241.529237] [<ffffffff8129342e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [ 241.530625] [<ffffffff815da51a>] int_signal+0x12/0x17 [ 241.532009] no locks held by gnome-settings-/3156. [ 241.533386] INFO: task gnome-settings-:3157 blocked for more than 120 seconds. [ 241.534778] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 241.536196] gnome-settings- D 00000000ffffffff 5432 3157 1 0x00000000 [ 241.537632] ffff8801279efcc8 0000000000000046 ffff88012993c580 0000000000000246 [ 241.539069] ffff8801279effd8 ffff8801279effd8 ffff8801279effd8 ffff8801279effd8 [ 241.540515] ffff88012661e840 ffff88012993c580 ffff880128cb0b80 ffff88012993c580 [ 241.541961] Call Trace: [ 241.543377] [<ffffffff815d8064>] schedule+0x24/0x70 [ 241.544802] [<ffffffff81043945>] exit_mm+0x85/0x120 [ 241.546226] [<ffffffff8104628f>] do_exit+0x13f/0x580 [ 241.547642] [<ffffffff81046957>] do_group_exit+0x47/0xb0 [ 241.549053] [<ffffffff810597ef>] get_signal_to_deliver+0x21f/0x580 [ 241.550468] [<ffffffff815d940b>] ? _raw_spin_unlock_irq+0x2b/0x50 [ 241.551878] [<ffffffff81002014>] do_signal+0x24/0x120 [ 241.553297] [<ffffffff81122e77>] ? might_fault+0x57/0xb0 [ 241.554726] [<ffffffff815da28c>] ? sysret_signal+0x5/0x47 [ 241.556148] [<ffffffff81002195>] do_notify_resume+0x65/0xa0 [ 241.557588] [<ffffffff8129342e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [ 241.557590] [<ffffffff815da51a>] int_signal+0x12/0x17 [ 241.557595] no locks held by gnome-settings-/3157.
Partial revert of 8280d16172243702ed43432f826ca6130edb4086
From: Pavel Roskin <[email protected]>
This prevents hanging login on Fedora 16:
[ 241.482118] INFO: task gnome-settings-:3155 blocked for more than 120 seconds. [ 241.483499] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 241.484888] gnome-settings- D 0000000000000000 6136 3155 1 0x00000000 [ 241.486265] ffff8801298afcc8 0000000000000046 ffff88012993b420 0000000000000246 [ 241.487652] ffff8801298affd8 ffff8801298affd8 ffff8801298affd8 ffff8801298affd8 [ 241.489035] ffff88012993a2c0 ffff88012993b420 ffff880128cb0b80 ffff88012993b420 [ 241.490421] Call Trace: [ 241.491765] [<ffffffff815d8064>] schedule+0x24/0x70 [ 241.493116] [<ffffffff81043945>] exit_mm+0x85/0x120 [ 241.494467] [<ffffffff8104628f>] do_exit+0x13f/0x580 [ 241.495784] [<ffffffff81046957>] do_group_exit+0x47/0xb0 [ 241.497090] [<ffffffff810597ef>] get_signal_to_deliver+0x21f/0x580 [ 241.498384] [<ffffffff81002014>] do_signal+0x24/0x120 [ 241.499673] [<ffffffff815da28c>] ? sysret_signal+0x5/0x47 [ 241.500964] [<ffffffff81002195>] do_notify_resume+0x65/0xa0 [ 241.502239] [<ffffffff8129342e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [ 241.503525] [<ffffffff815da51a>] int_signal+0x12/0x17 [ 241.504813] no locks held by gnome-settings-/3155.
---
fs/coredump.c | 21 ++++++++++++++++++++- 1 files changed, 20 insertions(+), 1 deletions(-)
fs/coredump.c +20 -1
@@ -429,6 +429,16 @@ static void wait_for_dump_helpers(struct file *file) } +static inline void __clear_close_on_exec (int fd,struct fdtable *fdt) +{ +__clear_bit (fd, fdt->close_on_exec); +} + +static inline void __set_open_fd (int fd,struct fdtable *fdt) +{ +__set_bit (fd, fdt->open_fds); +} +/* * umh_pipe_setup * helper function to customize the process used
@@ -443,14 +453,23 @@ static void wait_for_dump_helpers(struct file *file)static int umh_pipe_setup (struct subprocess_info *info,struct cred *new) {struct file *files[2 ]; +struct fdtable *fdt;struct coredump_params *cp = (struct coredump_params *)info->data; +struct files_struct *cf = current->files;int err =create_pipe_files (files,0 );if (err)return err; cp->file = files[1 ]; -replace_fd (0 , files[0 ],0 ); +sys_close (0 ); +fd_install (0 , files[0 ]); +spin_lock (&cf->file_lock); + fdt =files_fdtable (cf); +__set_open_fd (0 , fdt); +__clear_close_on_exec (0 , fdt); +spin_unlock (&cf->file_lock); +/* and disallow core files too */ current->signal->rlim[RLIMIT_CORE ] = (struct rlimit ){1 ,1 };
Al Viro
maintainerQuoted 5 lines · Pavel Roskin
Hello!
I tried the current mainline Linux on Fedora 16
x64_64and found that I cannot login in gdm. I'm using gdm with LXDE. After a few minutes, kernel messages appear indicating a hung process gnome-settings-daemon.
What is it hanging on?
Quoted 8 lines
I'll try to figure out why
replace_fd()is not good inumh_pipe_setup(), but I'd like to report the problem as soon as possible, as it's very visible to the users and I don't want others to spend hours bisecting it.Signature · 2 lines
Regards, Pavel Roskin
[snip]
Quoted 69 lines
[ 241.483499] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 241.484888] gnome-settings- D 0000000000000000 6136 3155 1 0x00000000 [ 241.486265] ffff8801298afcc8 0000000000000046 ffff88012993b420 0000000000000246 [ 241.487652] ffff8801298affd8 ffff8801298affd8 ffff8801298affd8 ffff8801298affd8 [ 241.489035] ffff88012993a2c0 ffff88012993b420 ffff880128cb0b80 ffff88012993b420 [ 241.490421] Call Trace: [ 241.491765] [<ffffffff815d8064>] schedule+0x24/0x70 [ 241.493116] [<ffffffff81043945>] exit_mm+0x85/0x120 [ 241.494467] [<ffffffff8104628f>] do_exit+0x13f/0x580 [ 241.495784] [<ffffffff81046957>] do_group_exit+0x47/0xb0 [ 241.497090] [<ffffffff810597ef>] get_signal_to_deliver+0x21f/0x580 [ 241.498384] [<ffffffff81002014>] do_signal+0x24/0x120 [ 241.499673] [<ffffffff815da28c>] ? sysret_signal+0x5/0x47 [ 241.500964] [<ffffffff81002195>] do_notify_resume+0x65/0xa0 [ 241.502239] [<ffffffff8129342e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [ 241.503525] [<ffffffff815da51a>] int_signal+0x12/0x17 [ 241.504813] no locks held by gnome-settings-/3155. [ 241.506095] INFO: task gnome-settings-:3156 blocked for more than 120 seconds. [ 241.507405] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 241.508721] gnome-settings- D 00000000ffffffff 5104 3156 1 0x00000000 [ 241.510056] ffff88011c80bcc8 0000000000000046 ffff88011c80bc78 ffffffff8109ad9d [ 241.511414] ffff88011c80bfd8 ffff88011c80bfd8 ffff88011c80bfd8 ffff88011c80bfd8 [ 241.512780] ffff8801279fd6e0 ffff88012993a2c0 ffff880129809d28 ffff88012993a2c0 [ 241.514134] Call Trace: [ 241.515480] [<ffffffff8109ad9d>] ? trace_hardirqs_on_caller+0x7d/0x120 [ 241.516857] [<ffffffff815d8064>] schedule+0x24/0x70 [ 241.518219] [<ffffffff81043945>] exit_mm+0x85/0x120 [ 241.519592] [<ffffffff8104628f>] do_exit+0x13f/0x580 [ 241.520952] [<ffffffff81046957>] do_group_exit+0x47/0xb0 [ 241.522315] [<ffffffff810597ef>] get_signal_to_deliver+0x21f/0x580 [ 241.523687] [<ffffffff81002014>] do_signal+0x24/0x120 [ 241.525066] [<ffffffff8109b8a4>] ? __lock_is_held+0x54/0x70 [ 241.526436] [<ffffffff815da28c>] ? sysret_signal+0x5/0x47 [ 241.527841] [<ffffffff81002195>] do_notify_resume+0x65/0xa0 [ 241.529237] [<ffffffff8129342e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [ 241.530625] [<ffffffff815da51a>] int_signal+0x12/0x17 [ 241.532009] no locks held by gnome-settings-/3156. [ 241.533386] INFO: task gnome-settings-:3157 blocked for more than 120 seconds. [ 241.534778] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 241.536196] gnome-settings- D 00000000ffffffff 5432 3157 1 0x00000000 [ 241.537632] ffff8801279efcc8 0000000000000046 ffff88012993c580 0000000000000246 [ 241.539069] ffff8801279effd8 ffff8801279effd8 ffff8801279effd8 ffff8801279effd8 [ 241.540515] ffff88012661e840 ffff88012993c580 ffff880128cb0b80 ffff88012993c580 [ 241.541961] Call Trace: [ 241.543377] [<ffffffff815d8064>] schedule+0x24/0x70 [ 241.544802] [<ffffffff81043945>] exit_mm+0x85/0x120 [ 241.546226] [<ffffffff8104628f>] do_exit+0x13f/0x580 [ 241.547642] [<ffffffff81046957>] do_group_exit+0x47/0xb0 [ 241.549053] [<ffffffff810597ef>] get_signal_to_deliver+0x21f/0x580 [ 241.550468] [<ffffffff815d940b>] ? _raw_spin_unlock_irq+0x2b/0x50 [ 241.551878] [<ffffffff81002014>] do_signal+0x24/0x120 [ 241.553297] [<ffffffff81122e77>] ? might_fault+0x57/0xb0 [ 241.554726] [<ffffffff815da28c>] ? sysret_signal+0x5/0x47 [ 241.556148] [<ffffffff81002195>] do_notify_resume+0x65/0xa0 [ 241.557588] [<ffffffff8129342e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [ 241.557590] [<ffffffff815da51a>] int_signal+0x12/0x17 [ 241.557595] no locks held by gnome-settings-/3157.fs/coredump.c +2
-0@@ -443,14 +453,23 @@ static void wait_for_dump_helpers(struct file *file)static int umh_pipe_setup (struct subprocess_info *info,struct cred *new) {struct file *files[2 ]; +struct fdtable *fdt;struct coredump_params *cp = (struct coredump_params *)info->data; +struct files_struct *cf = current->files;int err =create_pipe_files (files,0 );if (err)return err;
fs/coredump.c static void wait_for_dump_helpers(struct file *file) · line 471
Quoted 10 lines
fs/coredump.c +7
-1cp->file = files[1 ]; -replace_fd (0 , files[0 ],0 ); +sys_close (0 ); +fd_install (0 , files[0 ]); +spin_lock (&cf->file_lock); + fdt =files_fdtable (cf); +__set_open_fd (0 , fdt); +__clear_close_on_exec (0 , fdt); +spin_unlock (&cf->file_lock);
Very interesting. Let's see what could be going on there. First of all, create_pipe_files() has return 0. There's only one exit where it can do so and it dereferences both files[0] and files[1] on the way there. Since that hadn't oopsed, they are both non-NULL.
IOW, replace_fd(0, files[0], 0) is equivalent to
{
int err;
struct file *f = files[0];
struct files_struct *files = current->files;
if (0 >= rlimit(RLIMIT_NOFILE))
return -EMFILE;
spin_lock(&files->file_lock);
err = expand_files(files, 0);
if (unlikely(err < 0))
goto out_unlock;
return do_dup2(files, f, 0, 0);out_unlock:
spin_unlock(&files->file_lock);
return err;
}Aha. We have the first thing to test - is RLIMIT_NOFILE set to 0 for that process, by any chance? We definitedly need to check replace_fd() return value, BTW. OK, suppose it wasn't 0. So we'd done expand_files(files, 0). expand_files() begins with
/* Do we need to expand? */
if (nr < fdt->max_fds)
return 0;
and ->max_fds is never going to be less than NR_OPEN_DEFAULT, which is
definitely positive. So expand_files(files, 0) is going to return 0
without doing anything. And we get to do_dup2():
fdt = files_fdtable(files);
tofree = fdt->fd[0];
if (!tofree && fd_is_open(0, fdt))
goto Ebusy;that really shouldn't be possible to hit in this case - it can happen only for shared descriptor table. Another thread would need to have already reserved fd 0, but hadn't got around to installing a reference to struct file into it. But we are called from the freshly created kernel thread, about to exec some userland binary. Those are spawned without CLONE_FILES in flags, so the table can't be shared. It's fresh from dup_fd() and this bit
/*
* The fd may be claimed in the fd bitmap but not yet
* instantiated in the files array if a sibling thread
* is partway through open(). So make sure that this
* fd is available to the new process.
*/
__clear_open_fd(open_files - i, new_fdt);
in there would have prevented anything of that kind.
Now we have tofree equal to whatever we used to have in ->fd[0] (realistically that's going to be NULL). Next we have
get_file(file);
rcu_assign_pointer(fdt->fd[0], file);
__set_open_fd(0, fdt);
if (0 & O_CLOEXEC)
__set_close_on_exec(fd, fdt);
else
__clear_close_on_exec(fd, fdt);
spin_unlock(&files->file_lock);
if (tofree)
filp_close(tofree, files);Now, note that sys_close(0) would have done something very similar -
file = fdt->fd[0];
if (!file)
goto out_unlock;
rcu_assign_pointer(fdt->fd[0], NULL);
__clear_close_on_exec(0, fdt);
__put_unused_fd(files, 0);
spin_unlock(&files->file_lock);
filp_close(file, files);
'file' here is what we had in 'tofree'. We'd ripped it out of descriptor
table and done filp_close() on it. When we follow with
fd_install(0, files[0]);
...
__set_open_fd(0, fdt);
__clear_close_on_exec(0, fdt);we have get_file() done on files[0], files[0] put into ->fd[0] (fd_install()), result of __put_unused(files, 0); undone (by __set_open_fd()) and we come to exactly the same situation as with replace_fd().
All right, so the next step in debugging is to print the damn
return value of replace_fd(). That should narrow the things down. Another interesting question, of course, is what makes that gnome turd coredump on each boot?
Quoted 9 lines · On Mon, 15 Oct 2012 22:51:27 +0100 Al Viro <[email protected]> wrote:
Quoted 6 lines · Pavel Roskin
Hello!
I tried the current mainline Linux on Fedora 16
x64_64and found that I cannot login in gdm. I'm using gdm with LXDE. After a few minutes, kernel messages appear indicating a hung process gnome-settings-daemon.What is it hanging on?
Sorry, I have no idea. I select my name, enter password and nothing happens. I can still move the mouse and select some widgets in gdm. I can use Ctrl-Alt-F2 to switch to the test console and login.
I attached gdb to the process and that's what I got:
(gdb) where
#0 0x0000003c19ae8803 in __GI___poll (fds=<optimized out>, nfds=<optimized out>, timeout=<optimized out>) at ../sysdeps/unix/sysv/linux/poll.c:87 #1 0x0000003c1ba45448 in g_main_context_poll (n_fds=10, fds=0x2096dc0, priority=<optimized out>, timeout=41758, context=0x1e3e4a0) at gmain.c:3402 #2 g_main_context_iterate (context=0x1e3e4a0, block=<optimized out>, dispatch=1, self=<optimized out>) at gmain.c:3084 #3 0x0000003c1ba45c85 in g_main_loop_run (loop=0x1f35b70) at gmain.c:3297 #4 0x00000033cf75198d in gtk_main () at gtkmain.c:1362 #5 0x0000000000403d28 in main (argc=1, argv=0x7fffe57b3a78) at main.c:459
(gdb)
I'm not sure it's what you asked.
Quoted 2 lines
Aha. We have the first thing to test - is
RLIMIT_NOFILEset to 0 for that process, by any chance?
No. I made a copy of replace_fd() called by umh_pipe_setup() only, and here's the output (debugging patch attached):
[ 15.792895] replace_fd_debug: rlimit(RLIMIT_NOFILE) = 1024 [ 15.792901] replace_fd_debug: file = ffff88011dd5db80 [ 15.792903] replace_fd_debug: expand_files returned 0 [ 15.792905] umh_pipe_setup: replace_fd_debug returned 0
Quoted 2 lines
We definitedly need to check
replace_fd()return value, BTW. OK, suppose it wasn't 0.
It's 0.
I made simplified functions replacing replace_fd() for umh_pipe_setup() by substituting parameters and expanding do_dup2(). Here's the combined function:
void replace_fd2(struct file *file)
{
struct fdtable *fdt;
struct files_struct *files = current->files;
/* old code */
sys_close(0);
fd_install(0, file);
spin_lock(&files->file_lock);
fdt = files_fdtable(files);
/* new code */
get_file(file);
rcu_assign_pointer(fdt->fd[0], file);
__set_open_fd(0, fdt);
__clear_close_on_exec(0, fdt);
spin_unlock(&files->file_lock);
}If the "new code" (two lines below the comment) is commented out and the "old code" is not, everything works. If the new code is used and the old code is commented out, I have a hang. Enabling all code leads to a hang too.
Quoted 4 lines
All right, so the next step in debugging is to print the damn
return value ofreplace_fd(). That should narrow the things down. Another interesting question, of course, is what makes that gnome turd coredump on each boot?
I guess some GNOME programs are "uncomfortable" when launched by LXDE. Considering that I'm running Fedora 16 with GNOME 3.2, I don't think anyone would care about my bug reports. But inability to login due to kernel changes is bad and should not happen.
Signature · 2 lines
Regards, Pavel Roskin
Debug replace_fd()
From: Pavel Roskin <[email protected]>
---
fs/coredump.c | 4 +++- fs/file.c | 27 +++++++++++++++++++++++++++ 2 files changed, 30 insertions(+), 1 deletions(-)
fs/coredump.c +3 -1
@@ -440,6 +440,7 @@ static void wait_for_dump_helpers(struct file *file)* is a special value that we use to trap recursive * core dumps */ +int replace_fd_debug (unsigned fd,struct file *file,unsigned flags);static int umh_pipe_setup (struct subprocess_info *info,struct cred *new) {struct file *files[2 ];
@@ -450,7 +451,8 @@ static int umh_pipe_setup(struct subprocess_info *info, struct cred *new) cp->file = files[1 ]; -replace_fd (0 , files[0 ],0 ); + err =replace_fd_debug (0 , files[0 ],0 ); +printk ("%s: replace_fd_debug returned %d\n" , __func__, err);/* and disallow core files too */ current->signal->rlim[RLIMIT_CORE ] = (struct rlimit ){1 ,1 };
fs/file.c +27 -0
@@ -913,6 +913,33 @@ out_unlock:return err; } +int replace_fd_debug (unsigned fd,struct file *file,unsigned flags); +int replace_fd_debug (unsigned fd,struct file *file,unsigned flags) +{ +int err; +struct files_struct *files = current->files; + +printk ("%s: rlimit(RLIMIT_NOFILE) = %ld\n" , __func__,rlimit (RLIMIT_NOFILE )); +printk ("%s: file = %p\n" , __func__, file); + +if (!file) +return __close_fd (files, fd); + +if (fd >=rlimit (RLIMIT_NOFILE )) +return -EMFILE ; + +spin_lock (&files->file_lock); + err =expand_files (files, fd); +printk ("%s: expand_files returned %d\n" , __func__, err); +if (unlikely (err <0 )) + goto out_unlock; +return do_dup2 (files, file, fd, flags); + +out_unlock: +spin_unlock (&files->file_lock); +return err; +} + SYSCALL_DEFINE3(dup3, unsigned int, oldfd, unsigned int, newfd, int, flags) {int err = -EBADF ;
Al Viro
maintainer I think I understand what's going on there. Add fput(files[0])
after that replace_fd(); we have a leak and while that's not the right way to fix it, that'd verify if anything else is going on there.
Quoted 4 lines · On Tue, 16 Oct 2012 00:27:05 +0100 Al Viro <[email protected]> wrote:
I think I understand what's going on there. Add
fput(files[0])after thatreplace_fd(); we have a leak and while that's not the right way to fix it, that'd verify if anything else is going on there.
Yes, it's working now! No more hang on login!
Signature · 2 lines
Regards, Pavel Roskin
Al Viro
maintainerQuoted 9 lines · Pavel Roskin
Quoted 4 lines · On Tue, 16 Oct 2012 00:27:05 +0100 Al Viro <[email protected]> wrote:
I think I understand what's going on there. Add
fput(files[0])after thatreplace_fd(); we have a leak and while that's not the right way to fix it, that'd verify if anything else is going on there.Yes, it's working now! No more hang on login!
That should be closer to the final variant.
fs/coredump.c +3 -2
@@ -450,11 +450,12 @@ static int umh_pipe_setup(struct subprocess_info *info, struct cred *new) cp->file = files[1 ]; -replace_fd (0 , files[0 ],0 ); + err =replace_fd (0 , files[0 ],0 ); +fput (files[0 ]);/* and disallow core files too */ current->signal->rlim[RLIMIT_CORE ] = (struct rlimit ){1 ,1 }; -return 0 ; +return err; }void do_coredump (siginfo_t *siginfo,struct pt_regs *regs)
security/selinux/hooks.c +7 -11
@@ -2132,18 +2132,14 @@ static inline void flush_unauthorized_files(const struct cred *cred,return ; devnull =dentry_open (&selinux_null,O_RDWR , cred); -if (!IS_ERR (devnull)) { -/* replace all the matching ones with this */ -do { -replace_fd (n -1 ,get_file (devnull),0 ); - }while ((n =iterate_fd (files, n, match_file, cred)) !=0 ); +if (IS_ERR (devnull)) + devnull =NULL ; +/* replace all the matching ones with this */ +do { +replace_fd (n -1 , devnull,0 ); + }while ((n =iterate_fd (files, n, match_file, cred)) !=0 ); +if (devnull)fput (devnull); - }else { -/* just close all the matching ones */ -do { -replace_fd (n -1 ,NULL ,0 ); - }while ((n =iterate_fd (files, n, match_file, cred)) !=0 ); - } }/*
Quoted 4 lines · On Tue, 16 Oct 2012 00:48:53 +0100 Al Viro <[email protected]> wrote:
Quoted 3 lines · Pavel Roskin
On Tue, 16 Oct 2012 00:27:05 +0100
Al Viro <[email protected]> wrote:
Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
I think I understand what's going on there. Add
fput(files[0])after thatreplace_fd(); we have a leak and while that's not the right way to fix it, that'd verify if anything else is going on there.Yes, it's working now! No more hang on login!
That should be closer to the final variant.
It works me, thank you! I don't use SELinux, so I could not really test the second part.
Signature · 2 lines
Regards, Pavel Roskin