fw_printenv is not working
Hi,
when i run fw_printenv , its not working..It shows:- fw_printenv: line 1:
syntax error: "(" unexpected error... Let me tell you what i did...
1) i copy the u-boot source code from my colleague and copy in my hard disk.
2) After then i set the environment through commnads. the commands which i run are
# make CROSS_COMPILE=arm-none-linux-gnueabi- ARCH=arm distclean
# make CROSS_COMPILE=arm-none-linux-gnueabi- ARCH=arm omap3_evm_config
# make CROSS_COMPILE=arm-none-linux-gnueabi- ARCH=arm
3) After then i go to /tools/env, where i configure the fw_env.config and
then run make command.
4) After ruuning the command i got crc32.c and fw_printenv.
5)i copied the fw_printenv into the SD-Card and insert the card into the
OMAP3EVM board.
6) after then when i use the command ./fw_printenv it throws the error
fw_printenv: line 1: syntax error: "(" unexpected error..
Can u please help me what i have to do... I think i am doing
something wrong...Signature · 2 lines
View this message in context: http://old.nabble.com/fw_printenv-is-not-working-tp29297562p29297562.html Sent from the Uboot - Users mailing list archive at Nabble.com.
Quoted 2 lines · On Thursday, July 29, 2010 11:21:22 mateer wrote:
when i run
fw_printenv, its not working..It shows:-fw_printenv: line 1:
syntax error: "(" unexpected error...
looks like your config file has a syntax error in it
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20100729/a662acb6/attachment.pgp
Hi Mateer,
I am also facing the same issue. I am also getting the error:fw_printenv: line 1: syntax error: "(" unexpected whenever I give command fw_printenv. I am using OMAPL138 EVM board.
Can u please help me... How did you resolve this error for your board?? Thanks in advance...Nih_a
Quoted 22 lines · mateer
Hi,
when i runfw_printenv, its not working..It shows:-fw_printenv: line
1: syntax error: "(" unexpected error... Let me tell you what i did...
1) i copy the u-boot source code from my colleague and copy in my hard disk.
2) After then i set the environment through commnads. the commands which i run are# make CROSS_COMPILE=arm-none-linux-gnueabi- ARCH=arm distclean # make CROSS_COMPILE=arm-none-linux-gnueabi- ARCH=arm omap3_evm_config # make CROSS_COMPILE=arm-none-linux-gnueabi- ARCH=arm 3) After then i go to /tools/env, where i configure the fw_env.config and then run make command. 4) After ruuning the command i got crc32.c and fw_printenv. 5)i copied the fw_printenv into the SD-Card and insert the card into the OMAP3EVM board. 6) after then when i use the command ./fw_printenv it throws the error fw_printenv: line 1: syntax error: "(" unexpected error.. Can u please help me what i have to do... I think i am doing something wrong...
Signature · 2 lines
View this message in context: http://old.nabble.com/fw_printenv-is-not-working-tp29297562p34585226.html Sent from the Uboot - Users mailing list archive at Nabble.com.
Dear Nih_a,
when replying to a mail, please make sure to maintain thread information, i. e. make sure to set appropriate In-reply-to: and
References: headers.
Quoted 4 lines · In message <[email protected]> you wrote:
I am also facing the same issue. I am also getting the error:
fw_printenv: line 1: syntax error: "(" unexpected whenever I give commandfw_printenv. I am using OMAPL138 EVM board.
I guess you did not read tools/env/README , or did you? Did you follow the instructions of setting HOSTCC= in the call to make ?
Best regards,
Wolfgang Denk
Signature · 7 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de When the tide of life turns against you And the current upsets your boat Don't waste tears on what might have been Just lie on your back and float.