arm: arm925t: remove SX1 board

SX1 does not build properly by itself, is not built as part of MAKEALL arm or MAKEALL -a arm, and is only present in Makefile, not boards.cfg. As it also has no entry in MAINTAINERS, it is orphan and non-functional. Remove it.

Signed-off-by Albert ARIBAUD <[email protected]>

---
 Makefile                  |   14 --
 board/sx1/Makefile        |   45 -----
 board/sx1/config.mk       |   19 ---
 board/sx1/lowlevel_init.S |  397 ---------------------------------------------
 board/sx1/sx1.c           |  123 --------------
 include/configs/SX1.h     |  189 ---------------------

Hi Albert,

Quoted 6 lines · On Mon, 15 Oct 2012 23:53:03 +0200 Albert ARIBAUD <[email protected]>…

SX1 does not build properly by itself, is not built as part of MAKEALL arm or MAKEALL -a arm, and is only present in Makefile, not boards.cfg. As it also has no entry in MAINTAINERS, it is orphan and non-functional. Remove it.

Quoted 8 lines

Signed-off-by Albert ARIBAUD <[email protected]>

---
 Makefile                  |   14 --
 board/sx1/Makefile        |   45 -----
 board/sx1/config.mk       |   19 ---
 board/sx1/lowlevel_init.S |  397 ---------------------------------------------
 board/sx1/sx1.c           |  123 --------------
 include/configs/SX1.h     |  189 ---------------------

I think this patch also should add an entry about this removed board to doc/README.scrapyard.

Thanks,
Anatolij

SX1 does not build properly by itself, is not built as part of MAKEALL arm or MAKEALL -a arm, and is only present in Makefile, not boards.cfg. As it also has no entry in MAINTAINERS, it is orphan and non-functional. Remove it.

Signed-off-by Albert ARIBAUD <[email protected]>

---
Changes in v2:
- updated doc/README.scrapyard

 Makefile                  |   14 --
 board/sx1/Makefile        |   45 -----
 board/sx1/config.mk       |   19 ---
 board/sx1/lowlevel_init.S |  397 ---------------------------------------------
 board/sx1/sx1.c           |  123 --------------
 doc/README.scrapyard      |    3 +-
 include/configs/SX1.h     |  189 ---------------------
 7 files changed, 2 insertions(+), 788 deletions(-)
 delete mode 100644 board/sx1/Makefile
 delete mode 100644 board/sx1/config.mk
 delete mode 100644 board/sx1/lowlevel_init.S
 delete mode 100644 board/sx1/sx1.c
 delete mode 100644 include/configs/SX1.h

Makefile +0 -14

index 08eecbb..46f2ff2 100644
@@ -748,20 +748,6 @@ $(obj).boards.depend:	boards.cfg
 lcname	= $(shell echo $(1) | sed -e 's/\(.*\)_config/\L\1/')
 ucname	= $(shell echo $(1) | sed -e 's/\(.*\)_config/\U\1/')
 
-#========================================================================
-# ARM
-#========================================================================
-
-SX1_stdout_serial_config \
-SX1_config:		unconfig
-	@mkdir -p $(obj)include
-	@if [ "$(findstring _stdout_serial_, $@)" ] ; then \
-		echo "#undef CONFIG_STDOUT_USBTTY" >> $(obj)include/config.h ; \
-	else \
-		echo "#define CONFIG_STDOUT_USBTTY" >> $(obj)include/config.h ; \
-	fi;
-	@$(MKCONFIG) -n $@ SX1 arm arm925t sx1
-
 #########################################################################
 ## ARM1176 Systems
 #########################################################################

board/sx1/Makefile deleted +0 -45

deleted file mode 100644
index 292459f..0000000
@@ -1,45 +0,0 @@
-#
-# (C) Copyright 2004-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB	= $(obj)lib$(BOARD).o
-
-COBJS	:= sx1.o
-SOBJS	:= lowlevel_init.o
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
-
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################

board/sx1/config.mk deleted +0 -19

deleted file mode 100644
index 441bea2..0000000
@@ -1,19 +0,0 @@
-#
-# (C) Copyright 2004
-# Wolfgang Denk, DENX Software Engineering, <[email protected]>
-#
-# SX1 board with OMAP1510 (ARM925T) cpu
-# see http://www.ti.com/ for more information on Texas Insturments
-#
-# SX1 has 1 bank of 256 MB SDRAM
-# Physical Address:
-# 1000'0000 to 2000'0000
-#
-#
-# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000  (mem base + reserved)
-#
-# we load ourself to 1108'0000
-#
-#
-
-CONFIG_SYS_TEXT_BASE = 0x11080000

board/sx1/lowlevel_init.S deleted +0 -397

deleted file mode 100644
index c1a811a..0000000
@@ -1,397 +0,0 @@
-/*
- * Board specific setup info
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- *
- * -- Some bits of code used from rrload's head_OMAP1510.s --
- * Copyright (C) 2002 RidgeRun, Inc.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-
-#if defined(CONFIG_OMAP1510)
-#include <./configs/omap1510.h>
-#endif
-
-#define OMAP1510_CLKS ((1<<EN_XORPCK)|(1<<EN_PERCK)|(1<<EN_TIMCK)|(1<<EN_GPIOCK))
-
-
-_TEXT_BASE:
-	.word	CONFIG_SYS_TEXT_BASE	 /* sdram load addr from config.mk */
-
-.globl lowlevel_init
-lowlevel_init:
-
-	/*
-	 * Configure 1510 pins functions to match our board.
-	 */
-	ldr	r0, REG_PULL_DWN_CTRL_0
-	ldr	r1, VAL_PULL_DWN_CTRL_0
-	str	r1, [r0]
-	ldr	r0, REG_PULL_DWN_CTRL_1
-	ldr	r1, VAL_PULL_DWN_CTRL_1
-	str	r1, [r0]
-	ldr	r0, REG_PULL_DWN_CTRL_2
-	ldr	r1, VAL_PULL_DWN_CTRL_2
-	str	r1, [r0]
-	ldr	r0, REG_PULL_DWN_CTRL_3
-	ldr	r1, VAL_PULL_DWN_CTRL_3
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_4
-	ldr	r1, VAL_FUNC_MUX_CTRL_4
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_5
-	ldr	r1, VAL_FUNC_MUX_CTRL_5
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_6
-	ldr	r1, VAL_FUNC_MUX_CTRL_6
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_7
-	ldr	r1, VAL_FUNC_MUX_CTRL_7
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_8
-	ldr	r1, VAL_FUNC_MUX_CTRL_8
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_9
-	ldr	r1, VAL_FUNC_MUX_CTRL_9
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_A
-	ldr	r1, VAL_FUNC_MUX_CTRL_A
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_B
-	ldr	r1, VAL_FUNC_MUX_CTRL_B
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_C
-	ldr	r1, VAL_FUNC_MUX_CTRL_C
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_D
-	ldr	r1, VAL_FUNC_MUX_CTRL_D
-	str	r1, [r0]
-	ldr	r0, REG_VOLTAGE_CTRL_0
-	ldr	r1, VAL_VOLTAGE_CTRL_0
-	str	r1, [r0]
-	ldr	r0, REG_TEST_DBG_CTRL_0
-	ldr	r1, VAL_TEST_DBG_CTRL_0
-	str	r1, [r0]
-	ldr	r0, REG_MOD_CONF_CTRL_0
-	ldr	r1, VAL_MOD_CONF_CTRL_0
-	str	r1, [r0]
-
-	/* Move to 1510 mode */
-	ldr	r0, REG_COMP_MODE_CTRL_0
-	ldr	r1, VAL_COMP_MODE_CTRL_0
-	str	r1, [r0]
-
-	/* Set up Traffic Ctlr*/
-	ldr r0, REG_TC_IMIF_PRIO
-	mov r1, #0x0
-	str r1, [r0]
-	ldr r0, REG_TC_EMIFS_PRIO
-	str r1, [r0]
-	ldr r0, REG_TC_EMIFF_PRIO
-	str r1, [r0]
-
-	ldr r0, REG_TC_EMIFS_CONFIG
-	ldr r1, [r0]
-	bic r1, r1, #0x08   /* clear the global power-down enable PDE bit */
-	bic r1, r1, #0x01   /* write protect flash by clearing the WP bit */
-	str r1, [r0]	    /* EMIFS GlB Configuration. (value 0x12 most likely) */
-
-	ldr r0, _GPIO_PIN_CONTROL_REG
-	mov r1,#0
-	orr r1, r1, #0x0001 /* M_PCM_SYNC */
-	orr r1, r1, #0x4000 /* IPC_ACTIVE */
-	strh r1,[r0]
-
-	ldr r0, _GPIO_DIR_CONTROL_REG
-	mov r1,#0
-	bic r1, r1, #0x0001 /* M_PCM_SYNC */
-	bic r1, r1, #0x4000 /* IPC_ACTIVE */
-	strh r1,[r0]
-
-	ldr r0, _GPIO_DATA_OUTPUT_REG
-	mov r1,#0
-	bic r1, r1, #0x0001 /* M_PCM_SYNC */
-	orr r1, r1, #0x4000 /* IPC_ACTIVE */
-	strh r1,[r0]
-
-	/* Setup some clock domains */
-	ldr r1, =OMAP1510_CLKS
-	ldr r0, REG_ARM_IDLECT2
-	strh r1, [r0]  /* CLKM, Clock domain control. */
-
-	mov r1, #0x01  /* PER_EN bit */
-	ldr r0, REG_ARM_RSTCT2
-	strh r1, [r0]  /* CLKM; Peripheral reset. */
-
-	/* Set CLKM to Sync-Scalable  */
-	/* I supposidly need to enable the dsp clock before switching */
-	mov r1, #0x1000
-	ldr r0, REG_ARM_SYSST
-	strh r1, [r0]
-	mov r0, #0x400
-1:
-	subs r0, r0, #0x1   /* wait for any bubbles to finish */
-	bne 1b
-
-	ldr r1, VAL_ARM_CKCTL  /* use 12Mhz ref, PER must be <= 50Mhz so /2 */
-	ldr r0, REG_ARM_CKCTL
-	strh r1, [r0]
-
-	/* setup DPLL 1 */
-	ldr r1, VAL_DPLL1_CTL
-	ldr r0, REG_DPLL1_CTL
-	strh r1, [r0]
-	ands r1, r1, #0x10  /* Check if PLL is enabled. */
-	beq lock_end	    /* Do not look for lock if BYPASS selected */
-2:
-	ldrh r1, [r0]
-	ands r1, r1, #0x01  /* Check the LOCK bit. */
-	beq 2b		    /* ...loop until bit goes hi. */
-lock_end:
-
-	/* Set memory timings corresponding to the new clock speed */
-
-	/* Check execution location to determine current execution location
-	 * and branch to appropriate initialization code.
-	 */
-	mov r0, #0x10000000		    /* Load physical SDRAM base. */
-	mov r1, pc			    /* Get current execution location. */
-	cmp r1, r0			    /* Compare. */
-	bge skip_sdram			    /* Skip over EMIF-fast initialization if running from SDRAM. */
-
-	/*
-	 * Delay for SDRAM initialization.
-	 */
-	mov r3, #0x1800			       /* value should be checked */
-3:
-	subs r3, r3, #0x1		      /* Decrement count */
-	bne 3b
-
-	/*
-	 * Set SDRAM control values. Disable refresh before MRS command.
-	 */
-	ldr r0, VAL_TC_EMIFF_SDRAM_CONFIG   /* get good value */
-	bic r3, r0, #0xC		    /* (BIT3|BIT2) ulConfig with auto-refresh disabled. */
-	orr r3, r3, #0x8000000		    /* (BIT27) Disable CLK when Power down or Self-Refresh */
-	orr r3, r3, #0x4000000		    /* BIT26 Power Down Enable */
-	ldr r2, REG_TC_EMIFF_SDRAM_CONFIG   /* Point to configuration register. */
-	str r3, [r2]			    /* Store the passed value with AR disabled. */
-
-	ldr r1, VAL_TC_EMIFF_MRS	    /* get MRS value */
-	ldr r2, REG_TC_EMIFF_MRS	    /* Point to MRS register. */
-	str r1, [r2]			    /* Store the passed value.*/
-
-	ldr r2, REG_TC_EMIFF_SDRAM_CONFIG   /* Point to configuration register. */
-	str r0, [r2]			    /* Store the passed value. */
-
-	/*
-	 * Delay for SDRAM initialization.
-	 */
-	mov r3, #0x1800
-4:
-	subs r3, r3, #1			    /* Decrement count. */
-	bne 4b
-
-skip_sdram:
-
-	/* slow interface */
-	ldr r1, VAL_TC_EMIFS_CS0_CONFIG
-	ldr r0, REG_TC_EMIFS_CS0_CONFIG
-	str r1, [r0] /* Chip Select 0 */
-	ldr r1, VAL_TC_EMIFS_CS1_CONFIG
-	ldr r0, REG_TC_EMIFS_CS1_CONFIG
-	str r1, [r0] /* Chip Select 1 */
-	ldr r1, VAL_TC_EMIFS_CS2_CONFIG
-	ldr r0, REG_TC_EMIFS_CS2_CONFIG
-	str r1, [r0] /* Chip Select 2 */
-	ldr r1, VAL_TC_EMIFS_CS3_CONFIG
-	ldr r0, REG_TC_EMIFS_CS3_CONFIG
-	str r1, [r0] /* Chip Select 3 */
-
-	/* back to arch calling code */
-	mov	pc, lr
-
-/* the literal pools origin */
-	.ltorg
-
-/* OMAP configuration registers */
-REG_FUNC_MUX_CTRL_0:		/* 32 bits */
-	.word 0xfffe1000
-REG_FUNC_MUX_CTRL_1:		/* 32 bits */
-	.word 0xfffe1004
-REG_FUNC_MUX_CTRL_2:		/* 32 bits */
-	.word 0xfffe1008
-REG_COMP_MODE_CTRL_0:		/* 32 bits */
-	.word 0xfffe100c
-REG_FUNC_MUX_CTRL_3:		/* 32 bits */
-	.word 0xfffe1010
-REG_FUNC_MUX_CTRL_4:		/* 32 bits */
-	.word 0xfffe1014
-REG_FUNC_MUX_CTRL_5:		/* 32 bits */
-	.word 0xfffe1018
-REG_FUNC_MUX_CTRL_6:		/* 32 bits */
-	.word 0xfffe101c
-REG_FUNC_MUX_CTRL_7:		/* 32 bits */
-	.word 0xfffe1020
-REG_FUNC_MUX_CTRL_8:		/* 32 bits */
-	.word 0xfffe1024
-REG_FUNC_MUX_CTRL_9:		/* 32 bits */
-	.word 0xfffe1028
-REG_FUNC_MUX_CTRL_A:		/* 32 bits */
-	.word 0xfffe102C
-REG_FUNC_MUX_CTRL_B:		/* 32 bits */
-	.word 0xfffe1030
-REG_FUNC_MUX_CTRL_C:		/* 32 bits */
-	.word 0xfffe1034
-REG_FUNC_MUX_CTRL_D:		/* 32 bits */
-	.word 0xfffe1038
-REG_PULL_DWN_CTRL_0:		/* 32 bits */
-	.word 0xfffe1040
-REG_PULL_DWN_CTRL_1:		/* 32 bits */
-	.word 0xfffe1044
-REG_PULL_DWN_CTRL_2:		/* 32 bits */
-	.word 0xfffe1048
-REG_PULL_DWN_CTRL_3:		/* 32 bits */
-	.word 0xfffe104c
-REG_VOLTAGE_CTRL_0:		/* 32 bits */
-	.word 0xfffe1060
-REG_TEST_DBG_CTRL_0:		/* 32 bits */
-	.word 0xfffe1070
-REG_MOD_CONF_CTRL_0:		/* 32 bits */
-	.word 0xfffe1080
-REG_TC_IMIF_PRIO:		/* 32 bits */
-	.word 0xfffecc00
-REG_TC_EMIFS_PRIO:		/* 32 bits */
-	.word 0xfffecc04
-REG_TC_EMIFF_PRIO:		/* 32 bits */
-	.word 0xfffecc08
-REG_TC_EMIFS_CONFIG:		/* 32 bits */
-	.word 0xfffecc0c
-REG_TC_EMIFS_CS0_CONFIG:	/* 32 bits */
-	.word 0xfffecc10
-REG_TC_EMIFS_CS1_CONFIG:	/* 32 bits */
-	.word 0xfffecc14
-REG_TC_EMIFS_CS2_CONFIG:	/* 32 bits */
-	.word 0xfffecc18
-REG_TC_EMIFS_CS3_CONFIG:	/* 32 bits */
-	.word 0xfffecc1c
-REG_TC_EMIFF_SDRAM_CONFIG:	/* 32 bits */
-	.word 0xfffecc20
-REG_TC_EMIFF_MRS:		/* 32 bits */
-	.word 0xfffecc24
-/* MPU clock/reset/power mode control registers */
-REG_ARM_CKCTL:			/* 16 bits */
-	.word 0xfffece00
-REG_ARM_IDLECT2:		/* 16 bits */
-	.word 0xfffece08
-REG_ARM_RSTCT2:			/* 16 bits */
-	.word 0xfffece14
-REG_ARM_SYSST:			/* 16 bits */
-	.word 0xfffece18
-/* DPLL control registers */
-REG_DPLL1_CTL:			/* 16 bits */
-	.word 0xfffecf00
-/* identification code register */
-REG_IDCODE:			/* 32 bits */
-	.word 0xfffed404
-
-/* SX1 specific */
-_GPIO_PIN_CONTROL_REG:
-	.word GPIO_PIN_CONTROL_REG
-_GPIO_DIR_CONTROL_REG:
-	.word GPIO_DIR_CONTROL_REG
-_GPIO_DATA_OUTPUT_REG:
-	.word GPIO_DATA_OUTPUT_REG
-
-VAL_COMP_MODE_CTRL_0:
-	.word 0x0000eaef
-VAL_FUNC_MUX_CTRL_4:
-	.word 0x00000000
-VAL_FUNC_MUX_CTRL_5:
-	.word 0x00000000
-VAL_FUNC_MUX_CTRL_6:
-	.word 0x00000001
-VAL_FUNC_MUX_CTRL_7:
-	.word 0x00001000
-VAL_FUNC_MUX_CTRL_8:
-	.word 0x00001240       /*[Knoller]  Value of Symbian Image Wing B2*/
-VAL_FUNC_MUX_CTRL_9:
-	.word 0x00201008
-VAL_FUNC_MUX_CTRL_A:
-	.word 0x00001000
-VAL_FUNC_MUX_CTRL_B:
-	.word 0x00000000
-VAL_FUNC_MUX_CTRL_C:
-	.word 0x09008001       /*[Knoller]  Value of Symbian Image Wing B2*/
-VAL_FUNC_MUX_CTRL_D:
-	.word 0x00000000
-VAL_PULL_DWN_CTRL_0:
-	.word 0xfffeffff
-VAL_PULL_DWN_CTRL_1:
-	.word 0xd1ffffec
-VAL_PULL_DWN_CTRL_2:
-	.word 0xffa80c5b
-VAL_PULL_DWN_CTRL_3:
-	.word 0xffffc0fe
-VAL_VOLTAGE_CTRL_0:
-	.word 0x00000007
-VAL_TEST_DBG_CTRL_0:
-	/* The OMAP5910 TRM says this register must be 0, but HelenConfRegs
-	 * says to write a 7.  Don't know what the right thing is to do, so
-	 * I'm leaving it at 7 since that's what was already here.
-	 */
-	.word 0x00000007
-VAL_MOD_CONF_CTRL_0:
-	.word 0x0da20000       /*[Knoller]  Value of Symbian Image Wing B2*/
-
-VAL_ARM_CKCTL:
-	.word 0x010D
-
-VAL_DPLL1_CTL:
-	.word 0x3A33   /*[Hertle] Value of Symbian Image*/
-
-VAL_TC_EMIFS_CS1_CONFIG_PRELIM:
-	.word 0x00001149
-
-VAL_TC_EMIFS_CS2_CONFIG_PRELIM:
-	.word 0x00004158
-
-VAL_TC_EMIFS_CS0_CONFIG:
-	.word 0x00213090       /*[Knoller]  Value of Symbian Image Wing B2*/
-
-VAL_TC_EMIFS_CS1_CONFIG:
-	.word 0x00215070       /*[Knoller]  Value of Symbian Image Wing B2*/
-
-VAL_TC_EMIFS_CS2_CONFIG:
-	.word 0x00001139       /*[Knoller]  Value of Symbian Image Wing B2*/
-
-VAL_TC_EMIFS_CS3_CONFIG:
-	.word 0x00001139       /*[Knoller]  Value of Symbian Image Wing B2*/
-
-VAL_TC_EMIFF_SDRAM_CONFIG:
-	.word 0x0105f0b4       /*[Knoller]  Value of Symbian Image Wing B2*/
-
-
-VAL_TC_EMIFF_MRS:
-	.word 0x00000027       /*[Knoller]  Value of Symbian Image Wing B2*/

board/sx1/sx1.c deleted +0 -123

deleted file mode 100644
index aaef76e..0000000
@@ -1,123 +0,0 @@
-/*
- * (C) Copyright 2004
- * Wolfgang Denk, DENX Software Engineering, <[email protected]>
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <[email protected]>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static void flash__init (void);
-static void ether__init (void);
-
-static inline void delay (unsigned long loops)
-{
-	__asm__ volatile ("1:\n"
-			  "subs %0, %1, #1\n"
-			  "bne 1b":"=r" (loops):"0" (loops));
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-int board_init (void)
-{
-	/* arch number of SX1 Board */
-	gd->bd->bi_arch_number = MACH_TYPE_SX1;
-
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0x10000100;
-
-/* kk - this speeds up your boot a quite a bit.	 However to make it
- *  work, you need make sure your kernel startup flush bug is fixed.
- *  ... rkw ...
- */
-	icache_enable ();
-
-	flash__init ();
-	ether__init ();
-	return 0;
-}
-
-
-int misc_init_r (void)
-{
-	/* volatile ushort *gdir = (ushort *) (GPIO_DIR_CONTROL_REG); */
-	/* volatile ushort *mdir = (ushort *) (MPUIO_DIR_CONTROL_REG); */
-
-	/* setup gpio direction to match board (no floats!) */
-	/**gdir = 0xCFF9; */
-	/**mdir = 0x103F; */
-
-	return (0);
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-static void flash__init (void)
-{
-#define CS0_CHIP_SELECT_REG 0xfffecc10
-#define CS3_CHIP_SELECT_REG 0xfffecc1c
-#define EMIFS_GlB_Config_REG 0xfffecc0c
-
-	unsigned int regval;
-
-	regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
-	regval = regval | 0x0001;	/* Turn off write protection for flash devices. */
-	if (regval & 0x0002) {
-		regval = regval & 0xfffd;	/* Swap CS0 and CS3 so that flash is visible at 0x0 and eeprom at 0x0c000000. */
-		/* If, instead, you want to reference flash at 0x0c000000, then it seemed the following were necessary. */
-		/* *((volatile unsigned int *)CS0_CHIP_SELECT_REG) = 0x202090; / * Overrides head.S setting of 0x212090 */
-		/* *((volatile unsigned int *)CS3_CHIP_SELECT_REG) = 0x202090; / * Let's flash chips be fully functional. */
-	}
-	*((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
-}
-
-
-/******************************
- Routine:
- Description:
-******************************/
-static void ether__init (void)
-{
-#define ETH_CONTROL_REG 0x0800000b
-	/* take the Ethernet controller out of reset and wait
-	 * for the EEPROM load to complete.
-	 */
-	*((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
-	udelay (3);
-}
-
-
-int dram_init (void)
-{
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
-	return 0;
-}

doc/README.scrapyard +2 -1

index d0f4716..ed779e2 100644
@@ -11,7 +11,8 @@ easily if here is something they might want to dig for...
 
 Board	Arch	CPU	removed	    Commit	last known maintainer/contact
 =============================================================================
-TQM85xx	powerpc	MPC85xx	-	  -		Stefan Roese <[email protected]>
+SX1	arm	arm925t	-         -
+TQM85xx	powerpc	MPC85xx	d923a5d5  2012-10-04	Stefan Roese <[email protected]>
 apollon arm     omap24xx 535c74f  2012-09-18    Kyungmin Park <[email protected]>
 tb0229	mips	mips32	3f3110d	  2011-12-12
 rmu	powerpc	MPC850	fb82fd7   2011-12-07	Wolfgang Denk <[email protected]>

include/configs/SX1.h deleted +0 -179

deleted file mode 100644
index 93d031c..0000000
@@ -1,189 +0,0 @@
-/*
- * (C) Copyright 2004
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_ARM925T	1		/* This is an arm925t CPU	*/
-#define CONFIG_OMAP	1		/* in a TI OMAP core	*/
-#define CONFIG_OMAP1510 1		/* which is in a 1510 (helen) */
-#define CONFIG_OMAP_SX1 1		/*	a SX1 Board  */
-
-/* input clock of PLL */
-#define CONFIG_SYS_CLK_FREQ	12000000	/* the SX1 has 12MHz input clock */
-
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_CMDLINE_TAG	 1	/* enable passing of ATAGs	*/
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG	 1
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128*1024)
-
-/*
- * Hardware drivers
- */
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
-#define CONFIG_SYS_NS16550_CLK		(CONFIG_SYS_CLK_FREQ)	/* can be 12M/32Khz or 48Mhz  */
-#define CONFIG_SYS_NS16550_COM1	0xfffb0000		/* uart1, bluetooth uart on helen */
-
-/*
- * select serial console configuration
- */
-#define CONFIG_SERIAL1		1	/* we use SERIAL 1 on SX1 */
-
-/*
- * USB device configuration
- */
-#define CONFIG_USB_DEVICE	1
-#define CONFIG_USB_TTY		1
-
-#define CONFIG_USBD_VENDORID		0x1234
-#define CONFIG_USBD_PRODUCTID		0x5678
-#define CONFIG_USBD_MANUFACTURER	"Siemens"
-#define CONFIG_USBD_PRODUCT_NAME	"SX1"
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP1510_I2C
-
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CONS_INDEX	1
-#define CONFIG_BAUDRATE		115200
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_I2C
-
-#undef CONFIG_CMD_NET
-
-
-#include <configs/omap1510.h>
-
-#define CONFIG_BOOTARGS		"mem=16M console=ttyS0,115200n8 root=/dev/mtdblock3 rw"
-#ifdef CONFIG_STDOUT_USBTTY
-#define CONFIG_PREBOOT		"setenv stdout usbtty;setenv stdin usbtty"
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-#define CONFIG_SYS_PROMPT		"SX1# " /* Monitor Command Prompt	*/
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x10000000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x12000000	/* 32 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x10000000	/* default load address */
-
-/* The 1510 has 3 timers, they can be driven by the RefClk (12MHz) or by DPLL1.
- * This time is further subdivided by a local divisor.
- */
-#define CONFIG_SYS_TIMERBASE	OMAP1510_TIMER1_BASE	/* use timer 1 */
-#define CONFIG_SYS_PTV		2	/* Divisor: 2^(PTV+1) => 8 */
-#define CONFIG_SYS_HZ		1000
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS	1	   /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1		0x10000000 /* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE	0x02000000 /* 32 MB */
-
-#define PHYS_FLASH_1		0x00000000 /* Flash Bank #1 */
-#define PHYS_FLASH_2		0x04000000 /* Flash Bank #2 */
-
-#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- * V1
- * PHYS_FLASH_SIZE_1			(16 << 10)	16 MB
- * PHYS_FLASH_SIZE_2			(8 << 10)	 8 MB
- * V2 only 1 flash
- * PHYS_FLASH_SIZE_1			(32 << 10)	32 MB
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks */
-#define PHYS_FLASH_SECT_SIZE	(128*1024) /* Size of a sector (128kB) */
-#define CONFIG_SYS_MAX_FLASH_SECT	(256)	/* max number of sectors on one chip */
-#define CONFIG_ENV_ADDR	(CONFIG_SYS_FLASH_BASE + PHYS_FLASH_SECT_SIZE) /* addr of environment */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE	/* Monitor at beginning of flash */
-#define CONFIG_SYS_MONITOR_LEN		PHYS_FLASH_SECT_SIZE	/* Reserve 1 sector */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE, PHYS_FLASH_2 }
-
-/*-----------------------------------------------------------------------
- * FLASH driver setup
- */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash memory is CFI compliant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use drivers/mtd/cfi_flash.c */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* Use buffered writes (~10x faster) */
-#define CONFIG_SYS_FLASH_PROTECTION	1	/* Use hardware sector protection */
-
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	(20*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	(20*CONFIG_SYS_HZ) /* Timeout for Flash Write */
-