Skip to contentSkip to conversation

Add USB host support for CM-T35

PATCH New Nikita Kiryanov 2 participants 4 messages Dec 2, 2012 – Dec 3, 2012

lore
Share & tools
lore

Nikita Kiryanov

author
#0 lore raw

v2 cover Add USB host support for CM-T35

Add USB host support for CM-T35. As a preparation, some register offset definitions are added to twl4030.h

Changes in V2:
- Added GPIO register offsets for twl4030
- Used twl4030 definitions from patch 1 in twl4030 functions instead of BASE_ADDR + <numerical offset>

Nikita Kiryanov (2):
twl4030: add gpio register offsets
cm-t35: add USB host support

 board/cm_t35/cm_t35.c    |   77 ++++++++++++++++++++++++++++++++++++++++++++++
 include/configs/cm_t35.h |    8 ++++-
 include/twl4030.h        |   44 ++++++++++++++++++++++++++
 3 files changed, 128 insertions(+), 1 deletion(-)
Signature · 1 line
1.7.10.4
author
#1 lore raw

PATCH v2 1/2 twl4030: add gpio register offsets

Add gpio register offsets for twl4030.

Signed-off-by Nikita Kiryanov <[email protected]>
Signed-off-by Igor Grinberg <[email protected]>
---
 include/twl4030.h |   44 ++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 44 insertions(+)
include/twl4030.h +44 -0
index 9cd32ab..e3b3806 100644
@@ -482,6 +482,50 @@
 #define TWL4030_USB_PHY_CLK_CTRL			0xFE
 #define TWL4030_USB_PHY_CLK_CTRL_STS			0xFF
 
+/* GPIO */
+#define TWL4030_GPIO_GPIODATAIN1			0x00
+#define TWL4030_GPIO_GPIODATAIN2			0x01
+#define TWL4030_GPIO_GPIODATAIN3			0x02
+#define TWL4030_GPIO_GPIODATADIR1			0x03
+#define TWL4030_GPIO_GPIODATADIR2			0x04
+#define TWL4030_GPIO_GPIODATADIR3			0x05
+#define TWL4030_GPIO_GPIODATAOUT1			0x06
+#define TWL4030_GPIO_GPIODATAOUT2			0x07
+#define TWL4030_GPIO_GPIODATAOUT3			0x08
+#define TWL4030_GPIO_CLEARGPIODATAOUT1			0x09
+#define TWL4030_GPIO_CLEARGPIODATAOUT2			0x0A
+#define TWL4030_GPIO_CLEARGPIODATAOUT3			0x0B
+#define TWL4030_GPIO_SETGPIODATAOUT1			0x0C
+#define TWL4030_GPIO_SETGPIODATAOUT2			0x0D
+#define TWL4030_GPIO_SETGPIODATAOUT3			0x0E
+#define TWL4030_GPIO_GPIO_DEBEN1			0x0F
+#define TWL4030_GPIO_GPIO_DEBEN2			0x10
+#define TWL4030_GPIO_GPIO_DEBEN3			0x11
+#define TWL4030_GPIO_GPIO_CTRL				0x12
+#define TWL4030_GPIO_GPIOPUPDCTR1			0x13
+#define TWL4030_GPIO_GPIOPUPDCTR2			0x14
+#define TWL4030_GPIO_GPIOPUPDCTR3			0x15
+#define TWL4030_GPIO_GPIOPUPDCTR4			0x16
+#define TWL4030_GPIO_GPIOPUPDCTR5			0x17
+#define TWL4030_GPIO_GPIO_ISR1A				0x19
+#define TWL4030_GPIO_GPIO_ISR2A				0x1A
+#define TWL4030_GPIO_GPIO_ISR3A				0x1B
+#define TWL4030_GPIO_GPIO_IMR1A				0x1C
+#define TWL4030_GPIO_GPIO_IMR2A				0x1D
+#define TWL4030_GPIO_GPIO_IMR3A				0x1E
+#define TWL4030_GPIO_GPIO_ISR1B				0x1F
+#define TWL4030_GPIO_GPIO_ISR2B				0x20
+#define TWL4030_GPIO_GPIO_ISR3B				0x21
+#define TWL4030_GPIO_GPIO_IMR1B				0x22
+#define TWL4030_GPIO_GPIO_IMR2B				0x23
+#define TWL4030_GPIO_GPIO_IMR3B				0x24
+#define TWL4030_GPIO_GPIO_EDR1				0x28
+#define TWL4030_GPIO_GPIO_EDR2				0x29
+#define TWL4030_GPIO_GPIO_EDR3				0x2A
+#define TWL4030_GPIO_GPIO_EDR4				0x2B
+#define TWL4030_GPIO_GPIO_EDR5				0x2C
+#define TWL4030_GPIO_GPIO_SIH_CTRL			0x2D
+
 /*
  * Convience functions to read and write from TWL4030
  *
Signature · 1 line
1.7.10.4
author
#2 lore raw

PATCH v2 2/2 cm-t35: add USB host support

In reply to Nikita Kiryanov

Add support for USB host ports on cm-t3530 and cm-t3730.

Signed-off-by Nikita Kiryanov <[email protected]>
Signed-off-by Igor Grinberg <[email protected]>

---
Changes in V2:
- Used twl4030 definitions from patch 1 in twl4030 functions instead of BASE_ADDR + <numerical offset>

 board/cm_t35/cm_t35.c    |   77 ++++++++++++++++++++++++++++++++++++++++++++++
 include/configs/cm_t35.h |    8 ++++-
 2 files changed, 84 insertions(+), 1 deletion(-)
board/cm_t35/cm_t35.c +77 -0
index 6c2e95b..19367df 100644
@@ -32,6 +32,7 @@
 #include <netdev.h>
 #include <net.h>
 #include <i2c.h>
+#include <usb.h>
 #include <twl4030.h>
 #include <linux/compiler.h>
 

@@ -41,6 +42,8 @@
 #include <asm/arch/mmc_host_def.h>
 #include <asm/arch/sys_proto.h>
 #include <asm/mach-types.h>
+#include <asm/ehci-omap.h>
+#include <asm/gpio.h>
 
 #include "eeprom.h"
 

@@ -260,6 +263,36 @@ static void cm_t3x_set_common_muxconf(void)
 	MUX_VAL(CP(HSUSB0_DATA6),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA6*/
 	MUX_VAL(CP(HSUSB0_DATA7),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA7*/
 
+	/* USB EHCI */
+	MUX_VAL(CP(ETK_D0_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT0*/
+	MUX_VAL(CP(ETK_D1_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT1*/
+	MUX_VAL(CP(ETK_D2_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT2*/
+	MUX_VAL(CP(ETK_D7_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT3*/
+	MUX_VAL(CP(ETK_D4_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT4*/
+	MUX_VAL(CP(ETK_D5_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT5*/
+	MUX_VAL(CP(ETK_D6_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT6*/
+	MUX_VAL(CP(ETK_D3_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT7*/
+	MUX_VAL(CP(ETK_D8_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DIR*/
+	MUX_VAL(CP(ETK_D9_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_NXT*/
+	MUX_VAL(CP(ETK_CTL_ES2),	(IDIS | PTD | DIS | M3)); /*HSUSB1_CLK*/
+	MUX_VAL(CP(ETK_CLK_ES2),	(IDIS | PTU | DIS | M3)); /*HSUSB1_STP*/
+
+	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT0*/
+	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT1*/
+	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT2*/
+	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT3*/
+	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT4*/
+	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT5*/
+	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT6*/
+	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT7*/
+	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DIR*/
+	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_NXT*/
+	MUX_VAL(CP(ETK_D10_ES2),	(IDIS | PTD | DIS | M3)); /*HSUSB2_CLK*/
+	MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTU | DIS | M3)); /*HSUSB2_STP*/
+
+	/* SB_T35_USB_HUB_RESET_GPIO */
+	MUX_VAL(CP(CAM_WEN),		(IDIS | PTD | DIS | M4)); /*GPIO_167*/
+
 	/* I2C1 */
 	MUX_VAL(CP(I2C1_SCL),		(IEN  | PTU | EN  | M0)); /*I2C1_SCL*/
 	MUX_VAL(CP(I2C1_SDA),		(IEN  | PTU | EN  | M0)); /*I2C1_SDA*/

@@ -461,3 +494,47 @@ void __weak get_board_serial(struct tag_serialnr *serialnr)
 	serialnr->low = 0;
 	serialnr->high = 0;
 };
+
+#ifdef CONFIG_USB_EHCI_OMAP
+struct omap_usbhs_board_data usbhs_bdata = {
+	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+};
+
+#define SB_T35_USB_HUB_RESET_GPIO	167
+int ehci_hcd_init(void)
+{
+	u8 val;
+	int offset;
+
+	if (gpio_request(SB_T35_USB_HUB_RESET_GPIO, "SB-T35 usb hub reset")) {
+		printf("Error: can't obtain GPIO %d for SB-T35 usb hub reset",
+				SB_T35_USB_HUB_RESET_GPIO);
+		return -1;
+	}
+
+	gpio_direction_output(SB_T35_USB_HUB_RESET_GPIO, 0);
+	udelay(10);
+	gpio_set_value(SB_T35_USB_HUB_RESET_GPIO, 1);
+	udelay(1000);
+
+	offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_GPIODATADIR1;
+	twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, &val, offset);
+	val |= 0xC0;
+	/* Set GPIO6 and GPIO7 of TPS65930 as output */
+	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, val, offset);
+	offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_SETGPIODATAOUT1;
+	/* Take both PHYs out of reset */
+	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0xC0, offset);
+	udelay(1);
+
+	return omap_ehci_hcd_init(&usbhs_bdata);
+}
+
+int ehci_hcd_stop(void)
+{
+	return omap_ehci_hcd_stop();
+}
+
+#endif /* CONFIG_USB_EHCI_OMAP */
include/configs/cm_t35.h +7 -1
index 46c556d..35e2280 100644
@@ -114,9 +114,15 @@
 #define CONFIG_DOS_PARTITION
 
 /* USB */
-#define CONFIG_MUSB_UDC
 #define CONFIG_USB_OMAP3
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_OMAP
+#define CONFIG_USB_ULPI
+#define CONFIG_USB_ULPI_VIEWPORT_OMAP
+#define CONFIG_USB_STORAGE
+#define CONFIG_MUSB_UDC
 #define CONFIG_TWL4030_USB
+#define CONFIG_CMD_USB
 
 /* USB device configuration */
 #define CONFIG_USB_DEVICE
Signature · 1 line
1.7.10.4
Applied
#3 lore raw

v2 cover Add USB host support for CM-T35

In reply to Nikita Kiryanov

Dear Nikita Kiryanov,

Quoted 12 lines

Add USB host support for CM-T35. As a preparation, some register offset definitions are added to twl4030.h

Changes in V2:
- Added GPIO register offsets for twl4030
- Used twl4030 definitions from patch 1 in twl4030 functions instead of BASE_ADDR + <numerical offset>

Nikita Kiryanov (2):
twl4030: add gpio register offsets
cm-t35: add USB host support

Quoted 5 lines
 board/cm_t35/cm_t35.c    |   77
++++++++++++++++++++++++++++++++++++++++++++++ include/configs/cm_t35.h | 
  8 ++++-
 include/twl4030.h        |   44 ++++++++++++++++++++++++++
 3 files changed, 128 insertions(+), 1 deletion(-)

Applied both, thanks!

Best regards,
Marek Vasut