Problem with "mmc: core: Do not rescan non-removable devices"
hi,
the commit below causes my wifi to disappear on suspend and never reappear.
Unfortunately the commentary says what the patch does but not why, so I cannot tell if simply reverting it is correct, or if something more subtle in needed.
My wifi chip is a "libertas" driven "Marvell" chip. It is permanently attached to port 1 on an OMAP3 'hsmmc' interface. So MMC_CAP_NONREMOVABLE seem appropriate and is set.
It is normally inactive and when the suspend code notices this it doesn't bother trying to suspend through the driver but just removes the core:
/*
* We simply "remove" the card in this case.
* It will be redetected on resume. (Calling
* bus_ops->remove() with a claimed host can
* deadlock.)
*/
(in mmc_suspend_host). Only it isn't redetected on resume because rescan_entered is set.
I guess we could clear rescan_entered at this point. Would that make sense? It seems to work.
drivers/mmc/core/core.c +1 -0
@@ -2433,6 +2433,7 @@ int mmc_suspend_host(struct mmc_host *host)mmc_claim_host (host);mmc_detach_bus (host);mmc_power_off (host); + host->rescan_entered =0 ;mmc_release_host (host); host->pm_flags =0 ; err =0 ;
Thanks,
NeilBrown
From 3339d1e33185798a45dbdb5ea6c0bec1c27ca5fd Mon Sep 17 00:00:00 2001
From: Johan Rudholm <[email protected]>
Date: Thu, 23 Aug 2012 13:40:55 +0200
Subject: [PATCH] mmc: core: Do not rescan non-removable devices
If MMC_CAP_NONREMOVABLE is set, only issue a detect job on init.
drivers/mmc/core/core.c +5 -0
@@ -2053,6 +2053,11 @@ void mmc_rescan(struct work_struct *work)if (host->rescan_disable)return ; +/* If there is a non-removable card registered, only scan once */ +if ((host->caps &MMC_CAP_NONREMOVABLE ) && host->rescan_entered) +return ; + host->rescan_entered =1 ; +mmc_bus_get (host);/*
include/linux/mmc/host.h +1 -0
@@ -300,6 +300,7 @@ struct mmc_host {#endif int rescan_disable;/* disable card detection */ +int rescan_entered;/* used with nonremovable devices */ struct mmc_card *card;/* device attached to this host */
Quoted 7 lines · NeilBrown
hi,
the commit below causes my wifi to disappear on suspend and never reappear.
Unfortunately the commentary says what the patch does but not why, so I cannot tell if simply reverting it is correct, or if something more subtle in needed.
Some more background to the patch; If the card slot is configured to be a non-removable card and it appears that the slot does not contain a card at boot; "mmc_rescan" should _not_ check at every suspend/resume cycle if a card has been inserted. It will mean unnecessary power up of the card slot and thus wast power for every suspend/resume cycle. Moreover it should not be needed since the card is not removable.
Quoted 5 lines
My wifi chip is a "libertas" driven "Marvell" chip. It is permanently attached to port 1 on an OMAP3 'hsmmc' interface. So
MMC_CAP_NONREMOVABLEseem appropriate and is set.
Quoted 10 lines
It is normally inactive and when the suspend code notices this it doesn't bother trying to suspend through the driver but just removes the core:
/*
* We simply "remove" the card in this case.
* It will be redetected on resume. (Calling
*bus_ops->remove()with a claimed host can
* deadlock.)
*/
(inmmc_suspend_host). Only it isn't redetected on resume becauserescan_enteredis set.
Correct, but this is how it is supposed to work.
An sdio functional driver (libertas) that handles non-removable sdio devices, shall implement suspend|resume callbacks for the function driver. Otherwise mmc_sdio_suspend function (drivers/mmc/core/sdio.c) will return "-ENOSYS" and trigger the card and the card device to be removed. That is not what you expect for non-removable device to happen.
So, I suggest to you implement the suspend|resume callbacks in your sdio func driver, that would do the trick I believe.
Quoted 56 lines
I guess we could clear
rescan_enteredat this point. Would that make sense? It seems to work.drivers/mmc/core/core.c +1
-0@@ -2433,6 +2433,7 @@ int mmc_suspend_host(struct mmc_host *host)mmc_claim_host (host);mmc_detach_bus (host);mmc_power_off (host); + host->rescan_entered =0 ;mmc_release_host (host); host->pm_flags =0 ; err =0 ;Thanks,
NeilBrownFrom
3339d1e33185798a45dbdb5ea6c0bec1c27ca5fdMon Sep 17 00:00:00 2001
From: Johan Rudholm <[email protected]>
Date: Thu, 23 Aug 2012 13:40:55 +0200
Subject: [PATCH] mmc: core: Do not rescan non-removable devicesIf
MMC_CAP_NONREMOVABLEis set, only issue a detect job on init.Signed-off-by Johan Rudholm <[email protected]>Acked-by Ulf Hansson <[email protected]>Acked-by Linus Walleij <[email protected]>Signed-off-by Chris Ball <[email protected]>drivers/mmc/core/core.c +5
-0@@ -2053,6 +2053,11 @@ void mmc_rescan(struct work_struct *work)if (host->rescan_disable)return ; +/* If there is a non-removable card registered, only scan once */ +if ((host->caps &MMC_CAP_NONREMOVABLE ) && host->rescan_entered) +return ; + host->rescan_entered =1 ; +mmc_bus_get (host);/* include/linux/mmc/host.h +0
-0
include/linux/mmc/host.h struct mmc_host { · line 306
Quoted 7 lines
include/linux/mmc/host.h +1
-0@@ -300,6 +300,7 @@ struct mmc_host {#endif int rescan_disable;/* disable card detection */ +int rescan_entered;/* used with nonremovable devices */ struct mmc_card *card;/* device attached to this host */
Kind regards
Ulf Hansson
Hi, all
Could you pls help view the log below and give some suggestion?
I see this patch disable the rescan when the card was non-removable. So non-removable card didn't need to detect the card. This can avoid to claim host for card detecting. But for sd card it still need to detect. When mmc_rescan invoke mmc_claim_host to claim host for detecting card it was often blocked for more than 120s because of long time read or write thread hold the host. Then the call trace represent.
In queue.c there was a thread(mmc_queue_thread) to handle the request. When they first fetch a request it will hold the host(mmc_claim_host) until all the request were handled. These request often need more than 120s to be complete. Then task hung appeared.
All the request can be complete with no err, just call trace will be generated. Did you ever met this issue before?
Expect your response.
Thanks in advance.
===================================================
<7>mmc0: 65536 bytes transferred: 0
<7>mmc0: CMD12 arg 00000000 flags 0000049d
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x0000000a
<7>mmc0: req done (CMD18): 0: 00000900 00000000 00000000 00000000 <7>mmc0: starting CMD18 arg 00829c98 flags 000000b5
<7>mmc0: blksz 512 blocks 128 flags 00000200 tsac 100 ms nsac 0
<7>sdhci [sdhci_data_irq()]: mmc0: DMA base 0x2e520000, transferred 0x060000 byt es, next 0x2e580000
INFO: task kworker/u:0:5 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u:0 D 00000000 0 5 2 0x00000000 Call Trace:
[ee04fd50] [44042028] 0x44042028
(unreliable)
[ee04fe10] [c0007a0c] __switch_to+0xa0/0xf0
[ee04fe30] [c04dd514] __schedule+0x1f8/0x4a4
[ee04fea0] [c04dd8a0] schedule+0x30/0xbc
[ee04feb0] [c0381698] __mmc_claim_host+0x98/0x19c
[ee04ff00] [c0385f7c] mmc_sd_detect+0x38/0xc0 [ee04ff10] [c0382b00] mmc_rescan+0x294/0x2e0 [ee04ff40] [c00661cc] process_one_work+0x140/0x3e0
[ee04ff70] [c0066bf8] worker_thread+0x18c/0x36c
[ee04ffb0] [c006bf10] kthread+0x7c/0x80
[ee04fff0] [c000de58] kernel_thread+0x4c/0x68
<7>mmc0: 65536 bytes transferred: 0
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
<7>mmc0: CMD12 arg 00000000 flags 0000049d
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x0000000a
<7>mmc0: req done (CMD18): 0: 00000900 00000000 00000000 00000000 <7>mmc0: starting CMD18 arg 00903a00 flags 000000b5
<7>mmc0: blksz 512 blocks 128 flags 00000200 tsac 100 ms nsac 0
<7>sdhci [sdhci_data_irq()]: mmc0: DMA base 0x2e530000, transferred 0x050000 byt es, next 0x2e580000
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
<7>mmc0: 65536 bytes transferred: 0
<7>mmc0: CMD12 arg 00000000 flags 0000049d
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x0000000a
<7>mmc0: req done (CMD18): 0: 00000900 00000000 00000000 00000000
<7>mmc0: blksz 512 blocks 128 flags 00000200 tsac 100 ms nsac 0
<7>sdhci [sdhci_data_irq()]: mmc0: DMA base 0x2e520000, transferred 0x060000 byt es, next 0x2e580000
<7>mmc0: 65536 bytes transferred: 0
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
<7>mmc0: CMD12 arg 00000000 flags 0000049d
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x0000000a
INFO: task kworker/u:0:5 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u:0 D 00000000 0 5 2 0x00000000 Call Trace:
[ee04fd50] [44042028] 0x44042028
(unreliable)
[ee04fe10] [c0007a0c] __switch_to+0xa0/0xf0
[ee04fe30] [c04dd514] __schedule+0x1f8/0x4a4
[ee04fea0] [c04dd8a0] schedule+0x30/0xbc
[ee04feb0] [c0381698] __mmc_claim_host+0x98/0x19c
[ee04ff00] [c0385f7c] mmc_sd_detect+0x38/0xc0
[ee04ff10] [c0382b00] mmc_rescan+0x294/0x2e0
[ee04ff40] [c00661cc] process_one_work+0x140/0x3e0 [ee04ff70] [c0066bf8] worker_thread+0x18c/0x36c
[ee04ffb0] [c006bf10] kthread+0x7c/0x80
[ee04fff0] [c000de58] kernel_thread+0x4c/0x68
<7>mmc0: CMD12 arg 00000000 flags 0000049d
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x0000000a
<7>mmc0: starting CMD18 arg 00ad6a70 flags 000000b5
<7>mmc0: blksz 512 blocks 128 flags 00000200 tsac 100 ms nsac 0
<7>sdhci [sdhci_data_irq()]: mmc0: DMA base 0x2e530000, transferred 0x050000 byt
===================================================
Regards
Haijun.
Quoted 94 lines
-----Original Message-----
From: [email protected] [mailto:linux-mmc- [email protected]] On Behalf Of NeilBrown
Sent: Sunday, December 16, 2012 1:37 PM
To: Johan Rudholm; Chris Ball
Cc: Ulf Hansson; Linus Walleij; [email protected]
Subject: Problem with "mmc: core: Do not rescan non-removable devices"hi,
the commit below causes my wifi to disappear on suspend and never
reappear.
Unfortunately the commentary says what the patch does but not why, so I
cannot tell if simply reverting it is correct, or if something more subtle in needed.My wifi chip is a "libertas" driven "Marvell" chip. It is permanently
attached to port 1 on an OMAP3 'hsmmc' interface. SoMMC_CAP_NONREMOVABLEseem appropriate and is set.It is normally inactive and when the suspend code notices this it
doesn't bother trying to suspend through the driver but just removes the core:
/*
* We simply "remove" the card in this case.
* It will be redetected on resume. (Calling
*bus_ops->remove()with a claimed host can
* deadlock.)
*/
(inmmc_suspend_host). Only it isn't redetected on resume becauserescan_enteredis set.I guess we could clear
rescan_enteredat this point. Would that make
sense?
It seems to work.drivers/mmc/core/core.c index renamed from drivers/mmc/core/core.c +0
-006c42cf..65b8935 100644
drivers/mmc/core/core.c +1
-0@@ -2433,6 +2433,7 @@ int mmc_suspend_host(struct mmc_host *host)mmc_claim_host (host);mmc_detach_bus (host);mmc_power_off (host); + host->rescan_entered =0 ;mmc_release_host (host); host->pm_flags =0 ; err =0 ;Thanks,
NeilBrownFrom
3339d1e33185798a45dbdb5ea6c0bec1c27ca5fdMon Sep 17 00:00:00 2001
From: Johan Rudholm <[email protected]>
Date: Thu, 23 Aug 2012 13:40:55 +0200
Subject: [PATCH] mmc: core: Do not rescan non-removable devicesIf
MMC_CAP_NONREMOVABLEis set, only issue a detect job on init.Signed-off-by Johan Rudholm <[email protected]>Acked-by Ulf Hansson <[email protected]>Acked-by Linus Walleij <[email protected]>Signed-off-by Chris Ball <[email protected]>drivers/mmc/core/core.c index renamed from drivers/mmc/core/core.c +0
-0835c9f0..af2c4d2 100644
drivers/mmc/core/core.c +5
-0@@ -2053,6 +2053,11 @@ void mmc_rescan(struct work_struct *work)if (host->rescan_disable)return ; +/* If there is a non-removable card registered, only scan once */ +if ((host->caps &MMC_CAP_NONREMOVABLE ) && host->rescan_entered) +return ; + host->rescan_entered =1 ; +mmc_bus_get (host);/* include/linux/mmc/host.h index renamed from include/linux/mmc/host.h +0
-0f578a71..d5d9bd4 100644
include/linux/mmc/host.h +1
-0@@ -300,6 +300,7 @@ struct mmc_host {#endif int rescan_disable;/* disable card detection */ +int rescan_entered;/* used with nonremovable devices */
Quoted 3 lines
struct
mmc_card*card; /* device attached to
this host */
iozone -Rab /smbshare/result.xls -i 0 -i 1 -f /smbshare/testfil
e -n 3.5G -g 3.5G -r 64k
Iozone: Performance Test of File I/O
Version $Revision: 3.263 $
Compiled for 32 bit mode.
Build: linux-powerpc
Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins
Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Jean-Marc Zucconi, Jeff Blomberg,
Erik Habbinga, Kris Strecker, Walter Wong.
Run began: Sat Feb 23 05:15:59 2013
Excel chart generation enabled
Auto Mode
Using minimum file size of 3145728 kilobytes.
Using maximum file size of 3145728 kilobytes.
Record Size 64 KB
Command line used: iozone -Rab /smbshare/result.xls -i 0 -i 1 -f /smbshare/testfile -n 3.5G -g 3.5G -r 64k Output is in Kbytes/sec
Time Resolution = 0.000001 seconds.
Processor cache size set to 1024 Kbytes.
Processor cache line size set to 32 bytes.
File stride size set to 17 * record size.
random random bkwd record stride
KB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread
3145728 64<7>mmc0: (CMD12): 0: 00000000 00000000 00000000 00000000
<7>sdhci [sdhci_data_irq()]: mmc0: DMA base 0x13ea0000, transferred 0x060000 bytes, next 0x13f00000 <7>mmc0: req done (CMD25): 0: 00000900 00000000 00000000 00000000
<7>sdhci [sdhci_data_irq()]: mmc0: DMA base 0x13180000, transferred 0x080000 bytes, next 0x13200000
<7>mmc0: (CMD12): 0: 00000000 00000000 00000000 00000000
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000008
<7>mmc0: blksz 512 blocks 128 flags 00000100 tsac 3200 ms nsac 16000
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
<7>sdhci [sdhci_data_irq()]: mmc0: DMA base 0x146c0000, transferred 0x040000 bytes, next 0x14700000 <7>mmc0: starting CMD25 arg 000f6858 flags 000000b5
<7>sdhci [sdhci_data_irq()]: mmc0: DMA base 0x119e0000, transferred 0x020000 bytes, next 0x11a00000 <7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000008
<7>mmc0: starting CMD25 arg 000ffea8 flags 000000b5
<7>mmc0: CMD12 arg 00000000 flags 0000049d
<7>mmc0: starting CMD25 arg 00126500 flags 000000b5
<7>mmc0: req done (CMD25): 0: 00000900 00000000 00000000 00000000
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
<7>mmc0: CMD12 arg 00000000 flags 0000049d
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000008
<7>mmc0: blksz 512 blocks 128 flags 00000100 tsac 3200 ms nsac 16000
<7>mmc0: req done (CMD13): 0: 00000900 00000000 00000000 00000000
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000008
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000002
<7>mmc0: starting CMD13 arg 00010000 flags 00000195
<7>mmc0: starting CMD25 arg 001976a0 flags 000000b5
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000008
<7>mmc0: starting CMD13 arg 00010000 flags 00000195
<7>mmc0: (CMD12): 0: 00000000 00000000 00000000 00000000 <7>mmc0: (CMD12): 0: 00000000 00000000 00000000 00000000 <7>mmc0: 65536 bytes transferred: 0 <7>mmc0: 65536 bytes transferred: 0
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000008
<7>mmc0: starting CMD25 arg 0026ca10 flags 000000b5
<7>sdhci [sdhci_data_irq()]: mmc0: DMA base 0x10cc0000, transferred 0x040000 bytes, next 0x10d00000 <7>mmc0: starting CMD25 arg 00276050 flags 000000b5
<7>mmc0: req done (CMD13): 0: 00000900 00000000 00000000 00000000
<7>mmc0: 65536 bytes transferred: 0
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000008
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
<7>mmc0: CMD12 arg 00000000 flags 0000049d
<7>mmc0: 65536 bytes transferred: 0
INFO: task kworker/u:2:785 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u:2 D 0000000000000000 0 785 2 0x00000000 Call Trace: [c0000002f6603790] [c000000000009518] .L13+0x2c/0x48 [c0000002f6603820] [c000000000655e1c] .__schedule+0x28c/0x650 [c0000002f6603aa0] [c0000000006562d0] .schedule+0x30/0xe0 [c0000002f6603b20] [c0000000004c04c0] .__mmc_claim_host+0xd0/0x240 [c0000002f6603c00] [c0000000004c462c] .mmc_detect+0x3c/0x110 [c0000002f6603c90] [c0000000004c1eec] .mmc_rescan+0x35c/0x3d0 [c0000002f6603d50] [c000000000069a50] .process_one_work+0x180/0x490 [c0000002f6603e10] [c00000000006a740] .worker_thread+0x1c0/0x450 [c0000002f6603ed0] [c000000000070c94] .kthread+0xb4/0xc0 [c0000002f6603f90] [c000000000015848] .kernel_thread+0x54/0x70 INFO: task kworker/u:2:785 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u:2 D 0000000000000000 0 785 2 0x00000000 Call Trace: [c0000002f6603790] [c000000000009518] .L13+0x2c/0x48 [c0000002f6603820] [c000000000655e1c] .__schedule+0x28c/0x650 [c0000002f6603aa0] [c0000000006562d0] .schedule+0x30/0xe0 [c0000002f6603b20] [c0000000004c04c0] .__mmc_claim_host+0xd0/0x240 [c0000002f6603c00] [c0000000004c462c] .mmc_detect+0x3c/0x110 [c0000002f6603c90] [c0000000004c1eec] .mmc_rescan+0x35c/0x3d0 [c0000002f6603d50] [c000000000069a50] .process_one_work+0x180/0x490 [c0000002f6603e10] [c00000000006a740] .worker_thread+0x1c0/0x450 [c0000002f6603ed0] [c000000000070c94] .kthread+0xb4/0xc0 [c0000002f6603f90] [c000000000015848] .kernel_thread+0x54/0x70 INFO: task kworker/u:2:785 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u:2 D 0000000000000000 0 785 2 0x00000000 Call Trace: [c0000002f6603790] [c000000000009518] .L13+0x2c/0x48 [c0000002f6603820] [c000000000655e1c] .__schedule+0x28c/0x650 [c0000002f6603aa0] [c0000000006562d0] .schedule+0x30/0xe0 [c0000002f6603b20] [c0000000004c04c0] .__mmc_claim_host+0xd0/0x240 [c0000002f6603c00] [c0000000004c462c] .mmc_detect+0x3c/0x110 [c0000002f6603c90] [c0000000004c1eec] .mmc_rescan+0x35c/0x3d0 [c0000002f6603d50] [c000000000069a50] .process_one_work+0x180/0x490 [c0000002f6603e10] [c00000000006a740] .worker_thread+0x1c0/0x450 [c0000002f6603ed0] [c000000000070c94] .kthread+0xb4/0xc0 [c0000002f6603f90] [c000000000015848] .kernel_thread+0x54/0x70 <7>mmc0: starting CMD13 arg 00010000 flags 00000195 INFO: task kworker/u:2:785 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u:2 D 0000000000000000 0 785 2 0x00000000 Call Trace: [c0000002f6603790] [c000000000009518] .L13+0x2c/0x48 [c0000002f6603820] [c000000000655e1c] .__schedule+0x28c/0x650 [c0000002f6603aa0] [c0000000006562d0] .schedule+0x30/0xe0 [c0000002f6603b20] [c0000000004c04c0] .__mmc_claim_host+0xd0/0x240 [c0000002f6603c00] [c0000000004c462c] .mmc_detect+0x3c/0x110 [c0000002f6603c90] [c0000000004c1eec] .mmc_rescan+0x35c/0x3d0 [c0000002f6603d50] [c000000000069a50] .process_one_work+0x180/0x490 [c0000002f6603e10] [c00000000006a740] .worker_thread+0x1c0/0x450 [c0000002f6603ed0] [c000000000070c94] .kthread+0xb4/0xc0 [c0000002f6603f90] [c000000000015848] .kernel_thread+0x54/0x70 INFO: task kworker/u:2:785 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u:2 D 0000000000000000 0 785 2 0x00000000 Call Trace: [c0000002f6603790] [c000000000009518] .L13+0x2c/0x48 [c0000002f6603820] [c000000000655e1c] .__schedule+0x28c/0x650 [c0000002f6603aa0] [c0000000006562d0] .schedule+0x30/0xe0 [c0000002f6603b20] [c0000000004c04c0] .__mmc_claim_host+0xd0/0x240 [c0000002f6603c00] [c0000000004c462c] .mmc_detect+0x3c/0x110 [c0000002f6603c90] [c0000000004c1eec] .mmc_rescan+0x35c/0x3d0 [c0000002f6603d50] [c000000000069a50] .process_one_work+0x180/0x490 [c0000002f6603e10] [c00000000006a740] .worker_thread+0x1c0/0x450 [c0000002f6603ed0] [c000000000070c94] .kthread+0xb4/0xc0 [c0000002f6603f90] [c000000000015848] .kernel_thread+0x54/0x70 <7>mmc0: (CMD12): 0: 00000000 00000000 00000000 00000000 INFO: task kworker/u:2:785 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u:2 D 0000000000000000 0 785 2 0x00000000 Call Trace: [c0000002f6603790] [c000000000009518] .L13+0x2c/0x48
[c0000002f6603820] [c000000000655e1c] .__schedule+0x28c/0x650 [c0000002f6603aa0] [c0000000006562d0] .schedule+0x30/0xe0 [c0000002f6603b20] [c0000000004c04c0] .__mmc_claim_host+0xd0/0x240 [c0000002f6603c00] [c0000000004c462c] .mmc_detect+0x3c/0x110 [c0000002f6603c90] [c0000000004c1eec] .mmc_rescan+0x35c/0x3d0 [c0000002f6603d50] [c000000000069a50] .process_one_work+0x180/0x490 [c0000002f6603e10] [c00000000006a740] .worker_thread+0x1c0/0x450 [c0000002f6603ed0] [c000000000070c94] .kthread+0xb4/0xc0 [c0000002f6603f90] [c000000000015848] .kernel_thread+0x54/0x70
INFO: task kworker/u:2:785 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u:2 D 0000000000000000 0 785 2 0x00000000 Call Trace: [c0000002f6603790] [c000000000009518] .L13+0x2c/0x48 [c0000002f6603820] [c000000000655e1c] .__schedule+0x28c/0x650 [c0000002f6603aa0] [c0000000006562d0] .schedule+0x30/0xe0 [c0000002f6603b20] [c0000000004c04c0] .__mmc_claim_host+0xd0/0x240 [c0000002f6603c00] [c0000000004c462c] .mmc_detect+0x3c/0x110 [c0000002f6603c90] [c0000000004c1eec] .mmc_rescan+0x35c/0x3d0 [c0000002f6603d50] [c000000000069a50] .process_one_work+0x180/0x490 [c0000002f6603e10] [c00000000006a740] .worker_thread+0x1c0/0x450 [c0000002f6603ed0] [c000000000070c94] .kthread+0xb4/0xc0 [c0000002f6603f90] [c000000000015848] .kernel_thread+0x54/0x70 <7>sdhci [sdhci_data_irq()]: mmc0: DMA base 0x115e0000, transferred 0x020000 bytes, next 0x11600000 INFO: task kworker/u:2:785 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u:2 D 0000000000000000 0 785 2 0x00000000 Call Trace: [c0000002f6603790] [c000000000009518] .L13+0x2c/0x48 [c0000002f6603820] [c000000000655e1c] .__schedule+0x28c/0x650 [c0000002f6603aa0] [c0000000006562d0] .schedule+0x30/0xe0 [c0000002f6603b20] [c0000000004c04c0] .__mmc_claim_host+0xd0/0x240 [c0000002f6603c00] [c0000000004c462c] .mmc_detect+0x3c/0x110 [c0000002f6603c90] [c0000000004c1eec] .mmc_rescan+0x35c/0x3d0 [c0000002f6603d50] [c000000000069a50] .process_one_work+0x180/0x490 [c0000002f6603e10] [c00000000006a740] .worker_thread+0x1c0/0x450 [c0000002f6603ed0] [c000000000070c94] .kthread+0xb4/0xc0 [c0000002f6603f90] [c000000000015848] .kernel_thread+0x54/0x70 <7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001 INFO: task kworker/u:2:785 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u:2 D 0000000000000000 0 785 2 0x00000000 Call Trace: [c0000002f6603790] [c000000000009518] .L13+0x2c/0x48 [c0000002f6603820] [c000000000655e1c] .__schedule+0x28c/0x650 [c0000002f6603aa0] [c0000000006562d0] .schedule+0x30/0xe0 [c0000002f6603b20] [c0000000004c04c0] .__mmc_claim_host+0xd0/0x240 [c0000002f6603c00] [c0000000004c462c] .mmc_detect+0x3c/0x110 [c0000002f6603c90] [c0000000004c1eec] .mmc_rescan+0x35c/0x3d0 [c0000002f6603d50] [c000000000069a50] .process_one_work+0x180/0x490 [c0000002f6603e10] [c00000000006a740] .worker_thread+0x1c0/0x450 [c0000002f6603ed0] [c000000000070c94] .kthread+0xb4/0xc0 [c0000002f6603f90] [c000000000015848] .kernel_thread+0x54/0x70 INFO: task kworker/u:2:785 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u:2 D 0000000000000000 0 785 2 0x00000000 Call Trace: [c0000002f6603790] [c000000000009518] .L13+0x2c/0x48 [c0000002f6603820] [c000000000655e1c] .__schedule+0x28c/0x650 [c0000002f6603aa0] [c0000000006562d0] .schedule+0x30/0xe0 [c0000002f6603b20] [c0000000004c04c0] .__mmc_claim_host+0xd0/0x240 [c0000002f6603c00] [c0000000004c462c] .mmc_detect+0x3c/0x110 [c0000002f6603c90] [c0000000004c1eec] .mmc_rescan+0x35c/0x3d0 [c0000002f6603d50] [c000000000069a50] .process_one_work+0x180/0x490 [c0000002f6603e10] [c00000000006a740] .worker_thread+0x1c0/0x450 [c0000002f6603ed0] [c000000000070c94] .kthread+0xb4/0xc0 [c0000002f6603f90] [c000000000015848] .kernel_thread+0x54/0x70
<7>mmc0: (CMD12): 0: 00000000 00000000 00000000 00000000
<7>sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000002
<7>mmc0: req done (CMD13): 0: 00000900 00000000 00000000 00000000
<7>sdhci [sdhci_data_irq()]: mmc0: DMA base 0x136b0000, transferred 0x050000 bytes, next 0x13700000