prepare for mx6dl/ mx6solo

PATCH New Troy Kisky 3 participants 15 messages Oct 23, 2012 – Jan 23, 2013

Subsystems (5)

Arm (32-bit) Arm i.MX and Layerscape Kbuild GPIO +1 more subsystems

lore

Share & tools

lore

Troy Kisky

author

2012-10-23 20:57 UTC #0 lore raw

cover prepare for mx6dl/ mx6solo

Each patch in this series should be able to be applied independently of the others.

These patch have been seen before but I marked this as version 1, because they were in the middle of another series previously.

Troy Kisky (5):
mx6: soc: update get_cpu_rev and get_imx_type for mx6solo/sololite
mx6: use CONFIG_MX6 instead of CONFIG_MX6Q
imx-common: cpu: add imx_ddr_size
arch-mx6: add mx6dl_pins.h
imximage.cfg: run files through C preprocessor

 .gitignore                                   |    1 +
 Makefile                                     |   11 +-
 arch/arm/cpu/armv7/mx6/soc.c                 |   32 ++-
 arch/arm/imx-common/cpu.c                    |   66 +++++-
 arch/arm/include/asm/arch-mx5/sys_proto.h    |   10 +-
 arch/arm/include/asm/arch-mx6/imx-regs.h     |    2 +
 arch/arm/include/asm/arch-mx6/mx6dl_pins.h   |  149 +++++++++++++
 arch/arm/include/asm/arch-mx6/sys_proto.h    |   10 +-
 board/esg/ima3-mx53/imximage.cfg             |  120 ++++++-----
 board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg |   90 ++++----
 board/freescale/mx25pdk/imximage.cfg         |   77 +++----
 board/freescale/mx51evk/imximage.cfg         |  114 +++++-----
 board/freescale/mx53ard/imximage_dd3.cfg     |   83 ++++----
 board/freescale/mx53evk/imximage.cfg         |   86 ++++----
 board/freescale/mx53loco/imximage.cfg        |   83 ++++----
 board/freescale/mx53smd/imximage.cfg         |   83 ++++----
 board/freescale/mx6qarm2/imximage.cfg        |   88 ++++----
 board/freescale/mx6qsabreauto/imximage.cfg   |   82 +++----
 board/genesi/mx51_efikamx/imximage_mx.cfg    |  132 ++++++------
 board/genesi/mx51_efikamx/imximage_sb.cfg    |  126 +++++------
 board/ttcontrol/vision2/imximage_hynix.cfg   |  295 ++++++++++++++------------
 drivers/gpio/mxc_gpio.c                      |    6 +-
 drivers/video/ipu_regs.h                     |    2 +-
 include/configs/mx6qarm2.h                   |    1 +
 include/configs/mx6qsabre_common.h           |    1 +
 include/configs/mx6qsabrelite.h              |    1 +
 26 files changed, 1036 insertions(+), 715 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-mx6/mx6dl_pins.h

Signature · 1 line

1.7.9.5

Troy Kisky

author

2012-10-23 20:57 UTC #1 lore raw

PATCH 1/5 mx6: soc: update get_cpu_rev and get_imx_type for mx6solo/sololite

Previously, the same value was returned for both mx6dl and mx6solo. Check number of processors to differeniate.
Also, a freescale patch says that sololite has its cpu/rev stored at 0x280 instead of 0x260.
I don't have a sololite to verify.

Signed-off-by Troy Kisky <[email protected]>

---

---
 arch/arm/cpu/armv7/mx6/soc.c              |   32 +++++++++++++++++++++--------
 arch/arm/imx-common/cpu.c                 |   16 ++++++++-------
 arch/arm/include/asm/arch-mx5/sys_proto.h |    9 +++++++-
 arch/arm/include/asm/arch-mx6/imx-regs.h  |    2 ++
 arch/arm/include/asm/arch-mx6/sys_proto.h |    9 +++++++-
 5 files changed, 51 insertions(+), 17 deletions(-)

arch/arm/cpu/armv7/mx6/soc.c +24 -8

index bc65767..a8aad5d 100644
@@ -31,17 +31,33 @@
 #include <asm/arch/sys_proto.h>
 #include <asm/imx-common/boot_mode.h>
 
+struct scu_regs {
+	u32	ctrl;
+	u32	config;
+	u32	status;
+	u32	invalidate;
+	u32	fpga_rev;
+};
+
 u32 get_cpu_rev(void)
 {
 	struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
-	int reg = readl(&anatop->digprog);
-
-	/* Read mx6 variant: quad, dual or solo */
-	int system_rev = (reg >> 4) & 0xFF000;
-	/* Read mx6 silicon revision */
-	system_rev |= (reg & 0xFF) + 0x10;
-
-	return system_rev;
+	u32 reg = readl(&anatop->digprog_sololite);
+	u32 type = ((reg >> 16) & 0xff);
+
+	if (type != MXC_CPU_MX6SL) {
+		reg = readl(&anatop->digprog);
+		type = ((reg >> 16) & 0xff);
+		if (type == MXC_CPU_MX6DL) {
+			struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR;
+			u32 cfg = readl(&scu->config) & 3;
+
+			if (!cfg)
+				type = MXC_CPU_MX6SOLO;
+		}
+	}
+	reg &= 0xff;		/* mx6 silicon revision */
+	return (type << 12) | (reg + 0x10);
 }
 
 void init_aips(void)

arch/arm/imx-common/cpu.c +9 -7

index a10d12d..102c254 100644
@@ -67,18 +67,20 @@ char *get_reset_cause(void)
 
 #if defined(CONFIG_DISPLAY_CPUINFO)
 
-static const char *get_imx_type(u32 imxtype)
+const char *get_imx_type(u32 imxtype)
 {
 	switch (imxtype) {
-	case 0x63:
+	case MXC_CPU_MX6Q:
 		return "6Q";	/* Quad-core version of the mx6 */
-	case 0x61:
-		return "6DS";	/* Dual/Solo version of the mx6 */
-	case 0x60:
+	case MXC_CPU_MX6DL:
+		return "6DL";	/* Dual Lite version of the mx6 */
+	case MXC_CPU_MX6SOLO:
+		return "6SOLO";	/* Solo version of the mx6 */
+	case MXC_CPU_MX6SL:
 		return "6SL";	/* Solo-Lite version of the mx6 */
-	case 0x51:
+	case MXC_CPU_MX51:
 		return "51";
-	case 0x53:
+	case MXC_CPU_MX53:
 		return "53";
 	default:
 		return "??";

arch/arm/include/asm/arch-mx5/sys_proto.h +8 -1

index 7b5246e..4435be1 100644
@@ -24,8 +24,15 @@
 #ifndef _SYS_PROTO_H_
 #define _SYS_PROTO_H_
 
-u32 get_cpu_rev(void);
+#define MXC_CPU_MX51		0x51
+#define MXC_CPU_MX53		0x53
+#define MXC_CPU_MX6SL		0x60
+#define MXC_CPU_MX6DL		0x61
+#define MXC_CPU_MX6SOLO		0x62
+#define MXC_CPU_MX6Q		0x63
+
 #define is_soc_rev(rev)	((get_cpu_rev() & 0xFF) - rev)
+u32 get_cpu_rev(void);
 void sdelay(unsigned long);
 void set_chipselect_size(int const);

arch/arm/include/asm/arch-mx6/imx-regs.h +2 -0

index 09ab010..3eb0081 100644
@@ -564,6 +564,8 @@ struct anatop_regs {
 	u32	usb2_misc_clr;		/* 0x258 */
 	u32	usb2_misc_tog;		/* 0x25c */
 	u32	digprog;		/* 0x260 */
+	u32	reserved1[7];
+	u32	digprog_sololite;	/* 0x280 */
 };
 
 #define ANATOP_PFD_480_PFD0_FRAC_SHIFT		0

arch/arm/include/asm/arch-mx6/sys_proto.h +8 -1

index 711b30d..6627bbc 100644
@@ -24,9 +24,16 @@
 #ifndef _SYS_PROTO_H_
 #define _SYS_PROTO_H_
 
-#define is_soc_rev(rev)	((get_cpu_rev() & 0xFF) - rev)
+#define MXC_CPU_MX51		0x51
+#define MXC_CPU_MX53		0x53
+#define MXC_CPU_MX6SL		0x60
+#define MXC_CPU_MX6DL		0x61
+#define MXC_CPU_MX6SOLO		0x62
+#define MXC_CPU_MX6Q		0x63
 
+#define is_soc_rev(rev)	((get_cpu_rev() & 0xFF) - rev)
 u32 get_cpu_rev(void);
+const char *get_imx_type(u32 imxtype);
 
 void set_vddsoc(u32 mv);

Signature · 1 line

1.7.9.5

Stefano Babic

2012-11-10 07:18 UTC #2 lore raw

PATCH 1/5 mx6: soc: update get_cpu_rev and get_imx_type for mx6solo/sololite

Quoted 8 lines · Troy Kisky

Previously, the same value was returned for both mx6dl and mx6solo. Check number of processors to differeniate.
Also, a freescale patch says that sololite has its cpu/rev stored at 0x280 instead of 0x260.
I don't have a sololite to verify.
Signed-off-by Troy Kisky <[email protected]>

Applied to -u-boot-imx, thanks.

Best regards,
Stefano Babic

Signature · 5 lines

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

Troy Kisky

author

2012-10-23 20:57 UTC #3 lore raw

PATCH 2/5 mx6: use CONFIG_MX6 instead of CONFIG_MX6Q

In reply to Troy Kisky

Use CONFIG_MX6 when the particular processor
variant isn't important.

Reserve the use of CONFIG_MX6Q to
specifically test for quad cores variant.

Signed-off-by Troy Kisky <[email protected]>

---
 drivers/gpio/mxc_gpio.c            |    6 +++---
 drivers/video/ipu_regs.h           |    2 +-
 include/configs/mx6qarm2.h         |    1 +
 include/configs/mx6qsabre_common.h |    1 +
 include/configs/mx6qsabrelite.h    |    1 +
 5 files changed, 7 insertions(+), 4 deletions(-)

drivers/gpio/mxc_gpio.c +3 -3

index 2c79bff..a388064 100644
@@ -42,14 +42,14 @@ static unsigned long gpio_ports[] = {
 	[1] = GPIO2_BASE_ADDR,
 	[2] = GPIO3_BASE_ADDR,
 #if defined(CONFIG_MX25) || defined(CONFIG_MX27) || defined(CONFIG_MX51) || \
-		defined(CONFIG_MX53) || defined(CONFIG_MX6Q)
+		defined(CONFIG_MX53) || defined(CONFIG_MX6)
 	[3] = GPIO4_BASE_ADDR,
 #endif
-#if defined(CONFIG_MX27) || defined(CONFIG_MX53) || defined(CONFIG_MX6Q)
+#if defined(CONFIG_MX27) || defined(CONFIG_MX53) || defined(CONFIG_MX6)
 	[4] = GPIO5_BASE_ADDR,
 	[5] = GPIO6_BASE_ADDR,
 #endif
-#if defined(CONFIG_MX53) || defined(CONFIG_MX6Q)
+#if defined(CONFIG_MX53) || defined(CONFIG_MX6)
 	[6] = GPIO7_BASE_ADDR,
 #endif
 };

drivers/video/ipu_regs.h +1 -1

index a43aa03..982e252 100644
@@ -55,7 +55,7 @@
 #define IPU_TPM_REG_BASE	0x01060000
 #define IPU_DC_TMPL_REG_BASE	0x01080000
 #define IPU_ISP_TBPR_REG_BASE	0x010C0000
-#elif defined(CONFIG_MX6Q)
+#elif defined(CONFIG_MX6)
 #define IPU_CPMEM_REG_BASE	0x00100000
 #define IPU_LUT_REG_BASE	0x00120000
 #define IPU_SRM_REG_BASE	0x00140000

include/configs/mx6qarm2.h +1 -0

index b425fed..e8ce6db 100644
@@ -22,6 +22,7 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#define CONFIG_MX6
 #define CONFIG_MX6Q
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO

include/configs/mx6qsabre_common.h +1 -0

index bfb9cd4..75eeda5 100644
@@ -17,6 +17,7 @@
 #ifndef __MX6QSABRE_COMMON_CONFIG_H
 #define __MX6QSABRE_COMMON_CONFIG_H
 
+#define CONFIG_MX6
 #define CONFIG_MX6Q
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO

include/configs/mx6qsabrelite.h +1 -0

index 5989eb2..3ce6cf7 100644
@@ -22,6 +22,7 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#define CONFIG_MX6
 #define CONFIG_MX6Q
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO

Signature · 1 line

1.7.9.5

Stefano Babic

2012-11-10 07:17 UTC #4 lore raw

PATCH 2/5 mx6: use CONFIG_MX6 instead of CONFIG_MX6Q

Quoted 8 lines · Troy Kisky

Use CONFIG_MX6 when the particular processor
variant isn't important.
Reserve the use of CONFIG_MX6Q to
specifically test for quad cores variant.
Signed-off-by Troy Kisky <[email protected]>
---

Applied to -u-boot-imx, thanks.

Best regards,
Stefano Babi

Signature · 5 lines

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

Troy Kisky

author

2012-10-23 20:57 UTC #5 lore raw

PATCH 3/5 imx-common: cpu: add imx_ddr_size

In reply to Troy Kisky

Read memory setup registers to determine size of available ram. This routine works for mx53/mx6x

I need this because when mx6solo called get_ram_size with a too large maximum size, the system hanged.

Signed-off-by Troy Kisky <[email protected]>

---

---
 arch/arm/imx-common/cpu.c                 |   50 +++++++++++++++++++++++++++++
 arch/arm/include/asm/arch-mx5/sys_proto.h |    1 +
 arch/arm/include/asm/arch-mx6/sys_proto.h |    1 +
 3 files changed, 52 insertions(+)

arch/arm/imx-common/cpu.c +50 -0

index 102c254..5081908 100644
@@ -65,6 +65,56 @@ char *get_reset_cause(void)
 	}
 }
 
+#if defined(CONFIG_MX53) || defined(CONFIG_MX6)
+#if defined(CONFIG_MX53)
+#define MEMCTL_BASE	ESDCTL_BASE_ADDR;
+#else
+#define MEMCTL_BASE	MMDC_P0_BASE_ADDR;
+#endif
+static const unsigned char col_lookup[] = {9, 10, 11, 8, 12, 9, 9, 9};
+static const unsigned char bank_lookup[] = {3, 2};
+
+struct esd_mmdc_regs {
+	uint32_t	ctl;
+	uint32_t	pdc;
+	uint32_t	otc;
+	uint32_t	cfg0;
+	uint32_t	cfg1;
+	uint32_t	cfg2;
+	uint32_t	misc;
+	uint32_t	scr;
+	uint32_t	ref;
+	uint32_t	rsvd1;
+	uint32_t	rsvd2;
+	uint32_t	rwd;
+	uint32_t	or;
+	uint32_t	mrr;
+	uint32_t	cfg3lp;
+	uint32_t	mr4;
+};
+
+#define ESD_MMDC_CTL_GET_ROW(mdctl)	((ctl >> 24) & 7)
+#define ESD_MMDC_CTL_GET_COLUMN(mdctl)	((ctl >> 20) & 7)
+#define ESD_MMDC_CTL_GET_WIDTH(mdctl)	((ctl >> 16) & 3)
+#define ESD_MMDC_CTL_GET_CS1(mdctl)	((ctl >> 30) & 1)
+#define ESD_MMDC_MISC_GET_BANK(mdmisc)	((misc >> 5) & 1)
+
+unsigned imx_ddr_size(void)
+{
+	struct esd_mmdc_regs *mem = (struct esd_mmdc_regs *)MEMCTL_BASE;
+	unsigned ctl = readl(&mem->ctl);
+	unsigned misc = readl(&mem->misc);
+	int bits = 11 + 0 + 0 + 1;      /* row + col + bank + width */
+
+	bits += ESD_MMDC_CTL_GET_ROW(ctl);
+	bits += col_lookup[ESD_MMDC_CTL_GET_COLUMN(ctl)];
+	bits += bank_lookup[ESD_MMDC_MISC_GET_BANK(misc)];
+	bits += ESD_MMDC_CTL_GET_WIDTH(ctl);
+	bits += ESD_MMDC_CTL_GET_CS1(ctl);
+	return 1 << bits;
+}
+#endif
+
 #if defined(CONFIG_DISPLAY_CPUINFO)
 
 const char *get_imx_type(u32 imxtype)

arch/arm/include/asm/arch-mx5/sys_proto.h +1 -0

index 4435be1..93ad1c6 100644
@@ -33,6 +33,7 @@
 
 #define is_soc_rev(rev)	((get_cpu_rev() & 0xFF) - rev)
 u32 get_cpu_rev(void);
+unsigned imx_ddr_size(void);
 void sdelay(unsigned long);
 void set_chipselect_size(int const);

arch/arm/include/asm/arch-mx6/sys_proto.h +1 -0

index 6627bbc..3193297 100644
@@ -34,6 +34,7 @@
 #define is_soc_rev(rev)	((get_cpu_rev() & 0xFF) - rev)
 u32 get_cpu_rev(void);
 const char *get_imx_type(u32 imxtype);
+unsigned imx_ddr_size(void);
 
 void set_vddsoc(u32 mv);

Signature · 1 line

1.7.9.5

Stefano Babic

2012-11-10 07:17 UTC #6 lore raw

PATCH 3/5 imx-common: cpu: add imx_ddr_size

Quoted 8 lines · Troy Kisky

Read memory setup registers to determine size of available ram. This routine works for mx53/mx6x
I need this because when mx6solo called get_ram_size with a too large maximum size, the system hanged.
Signed-off-by Troy Kisky <[email protected]>

Applied to -u-boot-imx, thanks.

Best regards,
Stefano Babic

Signature · 5 lines

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

Troy Kisky

author

2012-10-23 20:57 UTC #7 lore raw

PATCH 4/5 arch-mx6: add mx6dl_pins.h

In reply to Troy Kisky

Only the values used in the sabrelite board are added currently. Add more as other boards use them.

Signed-off-by Troy Kisky <[email protected]>

---
 arch/arm/include/asm/arch-mx6/mx6dl_pins.h |  149 ++++++++++++++++++++++++++++
 1 file changed, 149 insertions(+)
 create mode 100644 arch/arm/include/asm/arch-mx6/mx6dl_pins.h

arch/arm/include/asm/arch-mx6/mx6dl_pins.h new file +149 -0

new file mode 100644
index 0000000..79e2c4f
@@ -0,0 +1,149 @@
+/*
+ * Copyright (C) 2012 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ */
+
+#ifndef __ASM_ARCH_MX6_MX6DL_PINS_H__
+#define __ASM_ARCH_MX6_MX6DL_PINS_H__
+
+#include <asm/imx-common/iomux-v3.h>
+
+/* Use to set PAD control */
+#define PAD_CTL_HYS		(1 << 16)
+#define PAD_CTL_PUS_100K_DOWN	(0 << 14)
+#define PAD_CTL_PUS_47K_UP	(1 << 14)
+#define PAD_CTL_PUS_100K_UP	(2 << 14)
+#define PAD_CTL_PUS_22K_UP	(3 << 14)
+
+#define PAD_CTL_PUE		(1 << 13)
+#define PAD_CTL_PKE		(1 << 12)
+#define PAD_CTL_ODE		(1 << 11)
+#define PAD_CTL_SPEED_LOW	(1 << 6)
+#define PAD_CTL_SPEED_MED	(2 << 6)
+#define PAD_CTL_SPEED_HIGH	(3 << 6)
+#define PAD_CTL_DSE_DISABLE	(0 << 3)
+#define PAD_CTL_DSE_240ohm	(1 << 3)
+#define PAD_CTL_DSE_120ohm	(2 << 3)
+#define PAD_CTL_DSE_80ohm	(3 << 3)
+#define PAD_CTL_DSE_60ohm	(4 << 3)
+#define PAD_CTL_DSE_48ohm	(5 << 3)
+#define PAD_CTL_DSE_40ohm	(6 << 3)
+#define PAD_CTL_DSE_34ohm	(7 << 3)
+#define PAD_CTL_SRE_FAST	(1 << 0)
+#define PAD_CTL_SRE_SLOW	(0 << 0)
+
+#define IOMUX_CONFIG_SION 0x10
+#define NO_MUX_I                0
+#define NO_PAD_I                0
+enum {
+	MX6DL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK = IOMUX_PAD(0x03B0, 0x009C, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DI0_PIN15__IPU1_DI0_PIN15	= IOMUX_PAD(0x03B4, 0x00A0, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DI0_PIN2__IPU1_DI0_PIN2	= IOMUX_PAD(0x03B8, 0x00A4, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DI0_PIN3__IPU1_DI0_PIN3	= IOMUX_PAD(0x03BC, 0x00A8, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DI0_PIN4__GPIO_4_20		= IOMUX_PAD(0x03C0, 0x00AC, 5, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT0__IPU1_DISP0_DAT_0	= IOMUX_PAD(0x03C4, 0x00B0, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT1__IPU1_DISP0_DAT_1	= IOMUX_PAD(0x03C8, 0x00B4, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT10__IPU1_DISP0_DAT_10 = IOMUX_PAD(0x03CC, 0x00B8, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT11__IPU1_DISP0_DAT_11 = IOMUX_PAD(0x03D0, 0x00BC, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT12__IPU1_DISP0_DAT_12 = IOMUX_PAD(0x03D4, 0x00C0, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT13__IPU1_DISP0_DAT_13 = IOMUX_PAD(0x03D8, 0x00C4, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT14__IPU1_DISP0_DAT_14 = IOMUX_PAD(0x03DC, 0x00C8, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT15__IPU1_DISP0_DAT_15 = IOMUX_PAD(0x03E0, 0x00CC, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT16__IPU1_DISP0_DAT_16 = IOMUX_PAD(0x03E4, 0x00D0, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT17__IPU1_DISP0_DAT_17 = IOMUX_PAD(0x03E8, 0x00D4, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT18__IPU1_DISP0_DAT_18 = IOMUX_PAD(0x03EC, 0x00D8, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT19__IPU1_DISP0_DAT_19 = IOMUX_PAD(0x03F0, 0x00DC, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT2__IPU1_DISP0_DAT_2	 = IOMUX_PAD(0x03F4, 0x00E0, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT20__IPU1_DISP0_DAT_20 = IOMUX_PAD(0x03F8, 0x00E4, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT21__IPU1_DISP0_DAT_21 = IOMUX_PAD(0x03FC, 0x00E8, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT22__IPU1_DISP0_DAT_22 = IOMUX_PAD(0x0400, 0x00EC, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT23__IPU1_DISP0_DAT_23 = IOMUX_PAD(0x0404, 0x00F0, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT3__IPU1_DISP0_DAT_3	= IOMUX_PAD(0x0408, 0x00F4, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT4__IPU1_DISP0_DAT_4	= IOMUX_PAD(0x040C, 0x00F8, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT5__IPU1_DISP0_DAT_5	= IOMUX_PAD(0x0410, 0x00FC, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT6__IPU1_DISP0_DAT_6	= IOMUX_PAD(0x0414, 0x0100, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT7__IPU1_DISP0_DAT_7	= IOMUX_PAD(0x0418, 0x0104, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT8__IPU1_DISP0_DAT_8	= IOMUX_PAD(0x041C, 0x0108, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_DISP0_DAT9__IPU1_DISP0_DAT_9	= IOMUX_PAD(0x0420, 0x010C, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+	MX6DL_PAD_EIM_D16__ECSPI1_SCLK		= IOMUX_PAD(0x0514, 0x0144, 1, 0x07D8, 2, 0),
+	MX6DL_PAD_EIM_D17__ECSPI1_MISO		= IOMUX_PAD(0x0518, 0x0148, 1, 0x07DC, 2, 0),
+	MX6DL_PAD_EIM_D18__ECSPI1_MOSI		= IOMUX_PAD(0x051C, 0x014C, 1, 0x07E0, 2, 0),
+	MX6DL_PAD_EIM_D19__GPIO_3_19		= IOMUX_PAD(0x0520, 0x0150, 5, 0x0000, 0, 0),
+	MX6DL_PAD_EIM_D21__GPIO_3_21		= IOMUX_PAD(0x0528, 0x0158, 5, 0x0000, 0, 0),
+	MX6DL_PAD_EIM_D21__I2C1_SCL		= IOMUX_PAD(0x0528, 0x0158, 6 | IOMUX_CONFIG_SION, 0x0868, 1, 0),
+	MX6DL_PAD_EIM_D23__GPIO_3_23		= IOMUX_PAD(0x0530, 0x0160, 5, 0x0000, 0, 0),
+	MX6DL_PAD_EIM_D26__UART2_TXD		= IOMUX_PAD(0x053C, 0x016C, 4, 0x0000, 0, 0),
+	MX6DL_PAD_EIM_D27__UART2_RXD		= IOMUX_PAD(0x0540, 0x0170, 4, 0x0904, 1, 0),
+	MX6DL_PAD_EIM_D28__I2C1_SDA		= IOMUX_PAD(0x0544, 0x0174, 1 | IOMUX_CONFIG_SION, 0x086C, 1, 0),
+	MX6DL_PAD_EIM_D28__GPIO_3_28		= IOMUX_PAD(0x0544, 0x0174, 5, 0x0000, 0, 0),
+	MX6DL_PAD_ENET_MDC__ENET_MDC		= IOMUX_PAD(0x05B8, 0x01E8, 1, 0x0000, 0,  0),
+	MX6DL_PAD_ENET_MDIO__ENET_MDIO		= IOMUX_PAD(0x05BC, 0x01EC, 1, 0x0810, 0, 0),
+	MX6DL_PAD_ENET_REF_CLK__ENET_TX_CLK	= IOMUX_PAD(0x05C0, 0x01F0, 1, 0x0000, 0, 0),
+	MX6DL_PAD_ENET_RXD0__GPIO_1_27		= IOMUX_PAD(0x05C8, 0x01F8, 5, 0x0000, 0, 0),
+	MX6DL_PAD_GPIO_16__GPIO_7_11		= IOMUX_PAD(0x05E4, 0x0214, 5, 0x0000, 0, 0),
+	MX6DL_PAD_GPIO_16__I2C3_SDA		= IOMUX_PAD(0x05E4, 0x0214, 6 | IOMUX_CONFIG_SION, 0x087C, 1, 0),
+	MX6DL_PAD_GPIO_17__GPIO_7_12		= IOMUX_PAD(0x05E8, 0x0218, 5, 0x0000, 0, 0),
+	MX6DL_PAD_GPIO_18__GPIO_7_13		= IOMUX_PAD(0x05EC, 0x021C, 5, 0x0000, 0, 0),
+	MX6DL_PAD_GPIO_19__GPIO_4_5		= IOMUX_PAD(0x05F0, 0x0220, 5, 0x0000, 0, 0),
+	MX6DL_PAD_GPIO_5__GPIO_1_5		= IOMUX_PAD(0x0600, 0x0230, 5, 0x0000, 0, 0),
+	MX6DL_PAD_GPIO_5__I2C3_SCL		= IOMUX_PAD(0x0600, 0x0230, 6 | IOMUX_CONFIG_SION, 0x0878, 2, 0),
+	MX6DL_PAD_KEY_COL3__I2C2_SCL		= IOMUX_PAD(0x0638, 0x0250, 4 | IOMUX_CONFIG_SION, 0x0870, 1, 0),
+	MX6DL_PAD_KEY_COL3__GPIO_4_12		= IOMUX_PAD(0x0638, 0x0250, 5, 0x0000, 0, 0),
+	MX6DL_PAD_KEY_ROW3__I2C2_SDA		= IOMUX_PAD(0x064C, 0x0264, 4 | IOMUX_CONFIG_SION, 0x0874, 1, 0),
+	MX6DL_PAD_KEY_ROW3__GPIO_4_13		= IOMUX_PAD(0x064C, 0x0264, 5, 0x0000, 0, 0),
+	MX6DL_PAD_NANDF_D1__GPIO_2_1		= IOMUX_PAD(0x0670, 0x0288, 5, 0x0000, 0, 0),
+	MX6DL_PAD_NANDF_D2__GPIO_2_2		= IOMUX_PAD(0x0674, 0x028C, 5, 0x0000, 0, 0),
+	MX6DL_PAD_NANDF_D3__GPIO_2_3		= IOMUX_PAD(0x0678, 0x0290, 5, 0x0000, 0, 0),
+	MX6DL_PAD_NANDF_D4__GPIO_2_4		= IOMUX_PAD(0x067C, 0x0294, 5, 0x0000, 0, 0),
+	MX6DL_PAD_NANDF_D6__GPIO_2_6		= IOMUX_PAD(0x0684, 0x029C, 5, 0x0000, 0, 0),
+	MX6DL_PAD_RGMII_RD0__ENET_RGMII_RD0     = IOMUX_PAD(0x0694, 0x02AC, 1, 0x0818, 1, 0),
+	MX6DL_PAD_RGMII_RD0__GPIO_6_25		= IOMUX_PAD(0x0694, 0x02AC, 5, 0x0000, 0, 0),
+	MX6DL_PAD_RGMII_RD1__ENET_RGMII_RD1	= IOMUX_PAD(0x0698, 0x02B0, 1, 0x081C, 1, 0),
+	MX6DL_PAD_RGMII_RD1__GPIO_6_27		= IOMUX_PAD(0x0698, 0x02B0, 5, 0x0000, 0, 0),
+	MX6DL_PAD_RGMII_RD2__ENET_RGMII_RD2	= IOMUX_PAD(0x069C, 0x02B4, 1, 0x0820, 1, 0),
+	MX6DL_PAD_RGMII_RD2__GPIO_6_28		= IOMUX_PAD(0x069C, 0x02B4, 5, 0x0000, 0, 0),
+	MX6DL_PAD_RGMII_RD3__ENET_RGMII_RD3	= IOMUX_PAD(0x06A0, 0x02B8, 1, 0x0824, 1, 0),
+	MX6DL_PAD_RGMII_RD3__GPIO_6_29		= IOMUX_PAD(0x06A0, 0x02B8, 5, 0x0000, 0, 0),
+	MX6DL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	= IOMUX_PAD(0x06A4, 0x02BC, 1, 0x0828, 1, 0),
+	MX6DL_PAD_RGMII_RX_CTL__GPIO_6_24	= IOMUX_PAD(0x06A4, 0x02BC, 5, 0x0000, 0, 0),
+	MX6DL_PAD_RGMII_RXC__ENET_RGMII_RXC	= IOMUX_PAD(0x06A8, 0x02C0, 1, 0x0814, 1, 0),
+	MX6DL_PAD_RGMII_RXC__GPIO_6_30		= IOMUX_PAD(0x06A8, 0x02C0, 5, 0x0000, 0, 0),
+	MX6DL_PAD_RGMII_TD0__ENET_RGMII_TD0	= IOMUX_PAD(0x06AC, 0x02C4, 1, 0x0000, 0, 0),
+	MX6DL_PAD_RGMII_TD1__ENET_RGMII_TD1	= IOMUX_PAD(0x06B0, 0x02C8, 1, 0x0000, 0, 0),
+	MX6DL_PAD_RGMII_TD2__ENET_RGMII_TD2	= IOMUX_PAD(0x06B4, 0x02CC, 1, 0x0000, 0, 0),
+	MX6DL_PAD_RGMII_TD3__ENET_RGMII_TD3	= IOMUX_PAD(0x06B8, 0x02D0, 1, 0x0000, 0, 0),
+	MX6DL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	= IOMUX_PAD(0x06BC, 0x02D4, 1, 0x0000, 0, 0),
+	MX6DL_PAD_RGMII_TXC__ENET_RGMII_TXC	= IOMUX_PAD(0x06C0, 0x02D8, 1, 0x0000, 0, 0),
+	MX6DL_PAD_SD1_CMD__GPIO_1_18		= IOMUX_PAD(0x06C8, 0x02E0, 5, 0x0000, 0, 0),
+	MX6DL_PAD_SD1_DAT3__GPIO_1_21		= IOMUX_PAD(0x06D8, 0x02F0, 5, 0x0000, 0, 0),
+	MX6DL_PAD_SD3_CLK__USDHC3_CLK		= IOMUX_PAD(0x06F4, 0x030C, 0, 0x0934, 1, 0),
+	MX6DL_PAD_SD3_CMD__USDHC3_CMD		= IOMUX_PAD(0x06F8, 0x0310, 0 | IOMUX_CONFIG_SION, 0x0000, 0, 0),
+	MX6DL_PAD_SD3_DAT0__USDHC3_DAT0		= IOMUX_PAD(0x06FC, 0x0314, 0, 0x0000, 0, 0),
+	MX6DL_PAD_SD3_DAT1__USDHC3_DAT1		= IOMUX_PAD(0x0700, 0x0318, 0, 0x0000, 0, 0),
+	MX6DL_PAD_SD3_DAT2__USDHC3_DAT2		= IOMUX_PAD(0x0704, 0x031C, 0, 0x0000, 0, 0),
+	MX6DL_PAD_SD3_DAT3__USDHC3_DAT3		= IOMUX_PAD(0x0708, 0x0320, 0, 0x0000, 0, 0),
+	MX6DL_PAD_SD3_DAT5__GPIO_7_0		= IOMUX_PAD(0x0710, 0x0328, 5, 0x0000, 0, 0),
+	MX6DL_PAD_SD3_DAT6__UART1_RXD		= IOMUX_PAD(0x0714, 0x032C, 1, 0x08FC, 2, 0),
+	MX6DL_PAD_SD3_DAT7__UART1_TXD		= IOMUX_PAD(0x0718, 0x0330, 1, 0x0000, 0, 0),
+	MX6DL_PAD_SD4_CLK__USDHC4_CLK		= IOMUX_PAD(0x0720, 0x0338, 0, 0x0938, 1, 0),
+	MX6DL_PAD_SD4_CMD__USDHC4_CMD		= IOMUX_PAD(0x0724, 0x033C, 0 | IOMUX_CONFIG_SION, 0x0000, 0, 0),
+	MX6DL_PAD_SD4_DAT0__USDHC4_DAT0		= IOMUX_PAD(0x0728, 0x0340, 1, 0x0000, 0, 0),
+	MX6DL_PAD_SD4_DAT1__USDHC4_DAT1		= IOMUX_PAD(0x072C, 0x0344, 1, 0x0000, 0, 0),
+	MX6DL_PAD_SD4_DAT2__USDHC4_DAT2		= IOMUX_PAD(0x0730, 0x0348, 1, 0x0000, 0, 0),
+	MX6DL_PAD_SD4_DAT3__USDHC4_DAT3		= IOMUX_PAD(0x0734, 0x034C, 1, 0x0000, 0, 0),
+};
+#endif	/* __ASM_ARCH_MX6_MX6DL_PINS_H__ */

Signature · 1 line

1.7.9.5

Stefano Babic

2012-11-10 07:18 UTC #8 lore raw

PATCH 4/5 arch-mx6: add mx6dl_pins.h

Quoted 5 lines · Troy Kisky

Only the values used in the sabrelite board are added currently. Add more as other boards use them.
Signed-off-by Troy Kisky <[email protected]>
---

Applied to -u-boot-imx, thanks.

Best regards,
Stefano Babic

Signature · 5 lines

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

Troy Kisky

author

2012-10-23 20:57 UTC #9 lore raw

PATCH 5/5 imximage.cfg: run files through C preprocessor

In reply to Troy Kisky

The '#' used as comments in the files cause the preprocessor trouble, so change to /* */.

Signed-off-by Troy Kisky <[email protected]>

---
 .gitignore                                   |    1 +
 Makefile                                     |   11 +-
 board/esg/ima3-mx53/imximage.cfg             |  120 ++++++-----
 board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg |   90 ++++----
 board/freescale/mx25pdk/imximage.cfg         |   77 +++----
 board/freescale/mx51evk/imximage.cfg         |  114 +++++-----
 board/freescale/mx53ard/imximage_dd3.cfg     |   83 ++++----
 board/freescale/mx53evk/imximage.cfg         |   86 ++++----
 board/freescale/mx53loco/imximage.cfg        |   83 ++++----
 board/freescale/mx53smd/imximage.cfg         |   83 ++++----
 board/freescale/mx6qarm2/imximage.cfg        |   88 ++++----
 board/freescale/mx6qsabreauto/imximage.cfg   |   82 +++----
 board/genesi/mx51_efikamx/imximage_mx.cfg    |  132 ++++++------
 board/genesi/mx51_efikamx/imximage_sb.cfg    |  126 +++++------
 board/ttcontrol/vision2/imximage_hynix.cfg   |  295 ++++++++++++++------------
 15 files changed, 777 insertions(+), 694 deletions(-)

.gitignore +1 -0

index d91e91b..be09894 100644
@@ -15,6 +15,7 @@
 *.swp
 *.patch
 *.bin
+*.cfgtmp
 
 # Build tree
 /build-*

Makefile +8 -3

index 08eecbb..dce8239 100644
@@ -450,8 +450,12 @@ $(obj)u-boot.img:	$(obj)u-boot.bin
 			sed -e 's/"[	 ]*$$/ for $(BOARD) board"/') \
 		-d $< $@
 
-$(obj)u-boot.imx:       $(obj)u-boot.bin
-		$(obj)tools/mkimage -n  $(CONFIG_IMX_CONFIG) -T imximage \
+$(obj)$(patsubst "%",%,$(CONFIG_IMX_CONFIG)).cfgtmp: $(obj)%.cfgtmp : %
+		mkdir -p $(dir $@)
+		$(CC) -E -x c $< $(CPPFLAGS) -o $@
+
+$(obj)u-boot.imx: %.imx : %.bin $(obj)$(patsubst "%",%,$(CONFIG_IMX_CONFIG)).cfgtmp
+		$(obj)tools/mkimage -n  $(filter-out %.bin,$^) -T imximage \
 		-e $(CONFIG_SYS_TEXT_BASE) -d $< $@
 
 $(obj)u-boot.kwb:       $(obj)u-boot.bin

@@ -819,7 +823,8 @@ clean:
 	@$(MAKE) -C doc/DocBook/ cleandocs
 	@find $(OBJTREE) -type f \
 		\( -name 'core' -o -name '*.bak' -o -name '*~' -o -name '*.su' \
-		-o -name '*.o'	-o -name '*.a' -o -name '*.exe'	\) -print \
+		-o -name '*.o'	-o -name '*.a' -o -name '*.exe' \
+		-o -name '*.cfgtmp' \) -print \
 		| xargs rm -f
 
 # Removes everything not needed for testing u-boot

board/esg/ima3-mx53/imximage.cfg +66 ~~-54~~

153 lines not on this page · raw message

board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg +47 ~~-43~~

109 lines not on this page · raw message

board/freescale/mx25pdk/imximage.cfg +40 ~~-37~~

93 lines not on this page · raw message

board/freescale/mx51evk/imximage.cfg +60 ~~-54~~

147 lines not on this page · raw message

board/freescale/mx53ard/imximage_dd3.cfg +43 ~~-40~~

91 lines not on this page · raw message

board/freescale/mx53evk/imximage.cfg +44 ~~-42~~

94 lines not on this page · raw message

board/freescale/mx53loco/imximage.cfg +43 ~~-40~~

91 lines not on this page · raw message

board/freescale/mx53smd/imximage.cfg +43 ~~-40~~

91 lines not on this page · raw message

board/freescale/mx6qarm2/imximage.cfg +46 ~~-42~~

101 lines not on this page · raw message

board/freescale/mx6qsabreauto/imximage.cfg +43 ~~-39~~

96 lines not on this page · raw message

board/genesi/mx51_efikamx/imximage_mx.cfg +70 ~~-62~~

170 lines not on this page · raw message

board/genesi/mx51_efikamx/imximage_sb.cfg +66 ~~-60~~

158 lines not on this page · raw message

board/ttcontrol/vision2/imximage_hynix.cfg +157 ~~-138~~

366 lines not on this page · raw message

Signature · 1 line

1.7.9.5

Stefano Babic

2012-11-10 07:23 UTC #10 lore raw

PATCH 5/5 imximage.cfg: run files through C preprocessor

Quoted 5 lines · Troy Kisky

The '#' used as comments in the files cause the preprocessor trouble, so change to /* */.
Signed-off-by Troy Kisky <[email protected]>
---

Hi Troy,

Quoted 8 lines

 .gitignore                                   |    1 +
 Makefile                                     |   11 +-
 board/esg/ima3-mx53/imximage.cfg             |  120 ++++++-----
 board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg |   90 ++++----
 board/freescale/mx25pdk/imximage.cfg         |   77 +++----
 board/freescale/mx51evk/imximage.cfg         |  114 +++++-----
 board/freescale/mx53ard/imximage_dd3.cfg     |   83 ++++----
 board/freescale/mx53evk/imximage.cfg         |   86 ++++----

Quoted 9 lines

 board/freescale/mx53loco/imximage.cfg        |   83 ++++----
 board/freescale/mx53smd/imximage.cfg         |   83 ++++----
 board/freescale/mx6qarm2/imximage.cfg        |   88 ++++----
 board/freescale/mx6qsabreauto/imximage.cfg   |   82 +++----
 board/genesi/mx51_efikamx/imximage_mx.cfg    |  132 ++++++------
 board/genesi/mx51_efikamx/imximage_sb.cfg    |  126 +++++------
 board/ttcontrol/vision2/imximage_hynix.cfg   |  295 ++++++++++++++------------
 15 files changed, 777 insertions(+), 694 deletions(-)

I am not sure. I see that Tom agree using /* comment style, but I have not seen a general agreement where to move the rule (in which Makefile, I mean). Tom, is it ok for you to add the rule in the main Makefile ?

Stefano

Signature · 5 lines

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

Troy Kisky

author

2013-01-18 01:49 UTC #11 lore raw

PATCH v2 1/1 imximage.cfg: run files through C preprocessor

In reply to Troy Kisky

The '#' used as comments in the files cause the preprocessor trouble, so change to /* */.

Signed-off-by Troy Kisky <[email protected]>

---
v2: moved the mkimage call to arch/arm/imx-common Makefile updated spl/Makefile as well
added board/woodburn/imximage.cfg conversion

---
 .gitignore                                   |    1 +
 Makefile                                     |    8 +-
 arch/arm/cpu/arm926ejs/config.mk             |    2 +-
 arch/arm/cpu/armv7/config.mk                 |    2 +-
 arch/arm/imx-common/Makefile                 |   13 ++
 board/esg/ima3-mx53/imximage.cfg             |  120 ++++++-----
 board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg |   90 ++++----
 board/freescale/mx25pdk/imximage.cfg         |   77 +++----
 board/freescale/mx51evk/imximage.cfg         |  114 +++++-----
 board/freescale/mx53ard/imximage_dd3.cfg     |   83 ++++----
 board/freescale/mx53evk/imximage.cfg         |   86 ++++----
 board/freescale/mx53loco/imximage.cfg        |   83 ++++----
 board/freescale/mx53smd/imximage.cfg         |   83 ++++----
 board/freescale/mx6qarm2/imximage.cfg        |   88 ++++----
 board/freescale/mx6qsabreauto/imximage.cfg   |   82 +++----
 board/genesi/mx51_efikamx/imximage_mx.cfg    |  132 ++++++------
 board/genesi/mx51_efikamx/imximage_sb.cfg    |  126 +++++------
 board/ttcontrol/vision2/imximage_hynix.cfg   |  295 ++++++++++++++------------
 board/woodburn/imximage.cfg                  |    2 +-
 spl/Makefile                                 |    7 +-
 20 files changed, 791 insertions(+), 703 deletions(-)

.gitignore +1 -0

index a163728..e40eb7b 100644
@@ -15,6 +15,7 @@
 *.swp
 *.patch
 *.bin
+*.cfgtmp
 
 # Build tree
 /build-*

Makefile +4 -4

index 3305e8c..7ba7766 100644
@@ -467,9 +467,8 @@ $(obj)u-boot.img:	$(obj)u-boot.bin
 			sed -e 's/"[	 ]*$$/ for $(BOARD) board"/') \
 		-d $< $@
 
-$(obj)u-boot.imx:       $(obj)u-boot.bin
-		$(obj)tools/mkimage -n  $(CONFIG_IMX_CONFIG) -T imximage \
-		-e $(CONFIG_SYS_TEXT_BASE) -d $< $@
+$(OBJTREE)/u-boot.imx : $(obj)u-boot.bin $(SUBDIR_TOOLS) depend
+		$(MAKE) -C $(SRCTREE)/arch/arm/imx-common $@
 
 $(obj)u-boot.kwb:       $(obj)u-boot.bin
 		$(obj)tools/mkimage -n $(CONFIG_SYS_KWD_CONFIG) -T kwbimage \

@@ -843,7 +842,8 @@ clean:
 	@$(MAKE) -s -C doc/DocBook/ cleandocs
 	@find $(OBJTREE) -type f \
 		\( -name 'core' -o -name '*.bak' -o -name '*~' -o -name '*.su' \
-		-o -name '*.o'	-o -name '*.a' -o -name '*.exe'	\) -print \
+		-o -name '*.o'	-o -name '*.a' -o -name '*.exe' \
+		-o -name '*.cfgtmp' \) -print \
 		| xargs rm -f
 
 # Removes everything not needed for testing u-boot

arch/arm/cpu/arm926ejs/config.mk +1 -1

index 6a3a1bb..47f24f5 100644
@@ -34,6 +34,6 @@ PLATFORM_RELFLAGS += $(PF_RELFLAGS_SLB_AT)
 
 ifneq ($(CONFIG_IMX_CONFIG),)
 
-ALL-y	+= $(obj)u-boot.imx
+ALL-y	+= $(OBJTREE)/u-boot.imx
 
 endif

arch/arm/cpu/armv7/config.mk +1 -1

index 9c3e2f3..350e946 100644
@@ -40,5 +40,5 @@ PF_NO_UNALIGNED := $(call cc-option, -mno-unaligned-access,)
 PLATFORM_NO_UNALIGNED := $(PF_NO_UNALIGNED)
 
 ifneq ($(CONFIG_IMX_CONFIG),)
-ALL-y	+= $(obj)u-boot.imx
+ALL-y	+= $(OBJTREE)/u-boot.imx
 endif

arch/arm/imx-common/Makefile +13 -0

index b3e608e..6309fcd 100644
@@ -42,6 +42,19 @@ all:	$(obj).depend $(LIB)
 $(LIB):	$(OBJS)
 	$(call cmd_link_o_target, $(OBJS))
 
+$(OBJTREE)/$(patsubst "%",%,$(CONFIG_IMX_CONFIG)).cfgtmp: $(OBJTREE)/%.cfgtmp : $(SRCTREE)/%
+	mkdir -p $(dir $@)
+	$(CC) -E -x c $< $(CPPFLAGS) -o $@
+
+$(OBJTREE)/u-boot.imx: $(OBJTREE)/u-boot.bin $(OBJTREE)/$(patsubst "%",%,$(CONFIG_IMX_CONFIG)).cfgtmp
+	$(OBJTREE)/tools/mkimage -n $(filter-out %.bin,$^) -T imximage \
+	-e $(CONFIG_SYS_TEXT_BASE) -d $< $@
+
+$(OBJTREE)/SPL: $(OBJTREE)/spl/u-boot-spl.bin $(OBJTREE)/$(patsubst "%",%,$(CONFIG_IMX_CONFIG)).cfgtmp
+	$(OBJTREE)/tools/mkimage -n $(filter-out %.bin,$^) -T imximage \
+	-e $(CONFIG_SPL_TEXT_BASE) -d $< $@
+
+
 #########################################################################
 
 # defines $(obj).depend target

board/esg/ima3-mx53/imximage.cfg +66 ~~-54~~

153 lines not on this page · raw message

board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg +47 ~~-43~~

109 lines not on this page · raw message

board/freescale/mx25pdk/imximage.cfg +40 ~~-37~~

93 lines not on this page · raw message

board/freescale/mx51evk/imximage.cfg +60 ~~-54~~

147 lines not on this page · raw message

board/freescale/mx53ard/imximage_dd3.cfg +43 ~~-40~~

91 lines not on this page · raw message

board/freescale/mx53evk/imximage.cfg +44 ~~-42~~

94 lines not on this page · raw message

board/freescale/mx53loco/imximage.cfg +43 ~~-40~~

91 lines not on this page · raw message

board/freescale/mx53smd/imximage.cfg +43 ~~-40~~

91 lines not on this page · raw message

board/freescale/mx6qarm2/imximage.cfg +46 ~~-42~~

101 lines not on this page · raw message

board/freescale/mx6qsabreauto/imximage.cfg +43 ~~-39~~

96 lines not on this page · raw message

board/genesi/mx51_efikamx/imximage_mx.cfg +70 ~~-62~~

170 lines not on this page · raw message

board/genesi/mx51_efikamx/imximage_sb.cfg +66 ~~-60~~

158 lines not on this page · raw message

board/ttcontrol/vision2/imximage_hynix.cfg +157 ~~-138~~

366 lines not on this page · raw message

board/woodburn/imximage.cfg +1 -1

index b4cc8ec..ba42a5e 100644
@@ -1,4 +1,4 @@
 BOOT_FROM      sd
 
-# DDR2 init
+/* DDR2 init */
 DATA 4 0xB8001010 0x00000304

spl/Makefile +2 -5

index 6dbb105..d8efad0 100644
@@ -141,11 +141,8 @@ $(OBJTREE)/MLO.byteswap: $(obj)u-boot-spl.bin
 	$(OBJTREE)/tools/mkimage -T omapimage -n byteswap \
 		-a $(CONFIG_SPL_TEXT_BASE) -d $< $@
 
-ifneq ($(CONFIG_IMX_CONFIG),)
-$(OBJTREE)/SPL:	$(obj)u-boot-spl.bin
-	$(OBJTREE)/tools/mkimage -n  $(SRCTREE)/$(CONFIG_IMX_CONFIG) -T imximage \
-		-e $(CONFIG_SPL_TEXT_BASE) -d $< $@
-endif
+$(OBJTREE)/SPL : $(obj)u-boot-spl.bin depend
+		$(MAKE) -C $(SRCTREE)/arch/arm/imx-common $@
 
 ALL-y	+= $(obj)u-boot-spl.bin

Signature · 1 line

1.7.9.5

Albert ARIBAUD

2013-01-18 08:06 UTC #12 lore raw

PATCH v2 1/1 imximage.cfg: run files through C preprocessor

Hi Troy,

Quoted 2 lines · Troy Kisky

The '#' used as comments in the files cause the preprocessor trouble, so change to /* */.

This seems incomplete -- there's also a change to .gitignore regarding *.cfgtmp. For the sake of completeness, can you add a note in the commit message about it?

Amicalement,

Signature · 1 line

Albert.

Troy Kisky

author

2013-01-19 02:14 UTC #13 lore raw

PATCH v3 1/1 imximage.cfg: run files through C preprocessor

In reply to Troy Kisky

The '#' used as comments in the files cause the preprocessor trouble, so change to /* */.

The mkimage command which uses this preprocessor output was moved to arch/arm/imx-common/Makefile

.gitignore was updated to ignore .cfgtmp files.

Signed-off-by Troy Kisky <[email protected]>

---
v2: moved the mkimage call to arch/arm/imx-common Makefile updated spl/Makefile as well
added board/woodburn/imximage.cfg conversion

v3: added .gitignore to commit message
added mkimage command move to commit message

---
 .gitignore                                   |    1 +
 Makefile                                     |    8 +-
 arch/arm/cpu/arm926ejs/config.mk             |    2 +-
 arch/arm/cpu/armv7/config.mk                 |    2 +-
 arch/arm/imx-common/Makefile                 |   13 ++
 board/esg/ima3-mx53/imximage.cfg             |  120 ++++++-----
 board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg |   90 ++++----
 board/freescale/mx25pdk/imximage.cfg         |   77 +++----
 board/freescale/mx51evk/imximage.cfg         |  114 +++++-----
 board/freescale/mx53ard/imximage_dd3.cfg     |   83 ++++----
 board/freescale/mx53evk/imximage.cfg         |   86 ++++----
 board/freescale/mx53loco/imximage.cfg        |   83 ++++----
 board/freescale/mx53smd/imximage.cfg         |   83 ++++----
 board/freescale/mx6qarm2/imximage.cfg        |   88 ++++----
 board/freescale/mx6qsabreauto/imximage.cfg   |   82 +++----
 board/genesi/mx51_efikamx/imximage_mx.cfg    |  132 ++++++------
 board/genesi/mx51_efikamx/imximage_sb.cfg    |  126 +++++------
 board/ttcontrol/vision2/imximage_hynix.cfg   |  295 ++++++++++++++------------
 board/woodburn/imximage.cfg                  |    2 +-
 spl/Makefile                                 |    7 +-
 20 files changed, 791 insertions(+), 703 deletions(-)

.gitignore +1 -0

index a163728..e40eb7b 100644
@@ -15,6 +15,7 @@
 *.swp
 *.patch
 *.bin
+*.cfgtmp
 
 # Build tree
 /build-*

Makefile +4 -4

index 3305e8c..7ba7766 100644
@@ -467,9 +467,8 @@ $(obj)u-boot.img:	$(obj)u-boot.bin
 			sed -e 's/"[	 ]*$$/ for $(BOARD) board"/') \
 		-d $< $@
 
-$(obj)u-boot.imx:       $(obj)u-boot.bin
-		$(obj)tools/mkimage -n  $(CONFIG_IMX_CONFIG) -T imximage \
-		-e $(CONFIG_SYS_TEXT_BASE) -d $< $@
+$(OBJTREE)/u-boot.imx : $(obj)u-boot.bin $(SUBDIR_TOOLS) depend
+		$(MAKE) -C $(SRCTREE)/arch/arm/imx-common $@
 
 $(obj)u-boot.kwb:       $(obj)u-boot.bin
 		$(obj)tools/mkimage -n $(CONFIG_SYS_KWD_CONFIG) -T kwbimage \

@@ -843,7 +842,8 @@ clean:
 	@$(MAKE) -s -C doc/DocBook/ cleandocs
 	@find $(OBJTREE) -type f \
 		\( -name 'core' -o -name '*.bak' -o -name '*~' -o -name '*.su' \
-		-o -name '*.o'	-o -name '*.a' -o -name '*.exe'	\) -print \
+		-o -name '*.o'	-o -name '*.a' -o -name '*.exe' \
+		-o -name '*.cfgtmp' \) -print \
 		| xargs rm -f
 
 # Removes everything not needed for testing u-boot

arch/arm/cpu/arm926ejs/config.mk +1 -1

index 6a3a1bb..47f24f5 100644
@@ -34,6 +34,6 @@ PLATFORM_RELFLAGS += $(PF_RELFLAGS_SLB_AT)
 
 ifneq ($(CONFIG_IMX_CONFIG),)
 
-ALL-y	+= $(obj)u-boot.imx
+ALL-y	+= $(OBJTREE)/u-boot.imx
 
 endif

arch/arm/cpu/armv7/config.mk +1 -1

index 9c3e2f3..350e946 100644
@@ -40,5 +40,5 @@ PF_NO_UNALIGNED := $(call cc-option, -mno-unaligned-access,)
 PLATFORM_NO_UNALIGNED := $(PF_NO_UNALIGNED)
 
 ifneq ($(CONFIG_IMX_CONFIG),)
-ALL-y	+= $(obj)u-boot.imx
+ALL-y	+= $(OBJTREE)/u-boot.imx
 endif

arch/arm/imx-common/Makefile +13 -0

index b3e608e..6309fcd 100644
@@ -42,6 +42,19 @@ all:	$(obj).depend $(LIB)
 $(LIB):	$(OBJS)
 	$(call cmd_link_o_target, $(OBJS))
 
+$(OBJTREE)/$(patsubst "%",%,$(CONFIG_IMX_CONFIG)).cfgtmp: $(OBJTREE)/%.cfgtmp : $(SRCTREE)/%
+	mkdir -p $(dir $@)
+	$(CC) -E -x c $< $(CPPFLAGS) -o $@
+
+$(OBJTREE)/u-boot.imx: $(OBJTREE)/u-boot.bin $(OBJTREE)/$(patsubst "%",%,$(CONFIG_IMX_CONFIG)).cfgtmp
+	$(OBJTREE)/tools/mkimage -n $(filter-out %.bin,$^) -T imximage \
+	-e $(CONFIG_SYS_TEXT_BASE) -d $< $@
+
+$(OBJTREE)/SPL: $(OBJTREE)/spl/u-boot-spl.bin $(OBJTREE)/$(patsubst "%",%,$(CONFIG_IMX_CONFIG)).cfgtmp
+	$(OBJTREE)/tools/mkimage -n $(filter-out %.bin,$^) -T imximage \
+	-e $(CONFIG_SPL_TEXT_BASE) -d $< $@
+
+
 #########################################################################
 
 # defines $(obj).depend target

board/esg/ima3-mx53/imximage.cfg +66 ~~-54~~

153 lines not on this page · raw message

board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg +47 ~~-43~~

109 lines not on this page · raw message

board/freescale/mx25pdk/imximage.cfg +40 ~~-37~~

93 lines not on this page · raw message

board/freescale/mx51evk/imximage.cfg +60 ~~-54~~

147 lines not on this page · raw message

board/freescale/mx53ard/imximage_dd3.cfg +43 ~~-40~~

91 lines not on this page · raw message

board/freescale/mx53evk/imximage.cfg +44 ~~-42~~

94 lines not on this page · raw message

board/freescale/mx53loco/imximage.cfg +43 ~~-40~~

91 lines not on this page · raw message

board/freescale/mx53smd/imximage.cfg +43 ~~-40~~

91 lines not on this page · raw message

board/freescale/mx6qarm2/imximage.cfg +46 ~~-42~~

101 lines not on this page · raw message

board/freescale/mx6qsabreauto/imximage.cfg +43 ~~-39~~

96 lines not on this page · raw message

board/genesi/mx51_efikamx/imximage_mx.cfg +70 ~~-62~~

170 lines not on this page · raw message

board/genesi/mx51_efikamx/imximage_sb.cfg +66 ~~-60~~

158 lines not on this page · raw message

board/ttcontrol/vision2/imximage_hynix.cfg +157 ~~-138~~

366 lines not on this page · raw message

board/woodburn/imximage.cfg +1 -1

index b4cc8ec..ba42a5e 100644
@@ -1,4 +1,4 @@
 BOOT_FROM      sd
 
-# DDR2 init
+/* DDR2 init */
 DATA 4 0xB8001010 0x00000304

spl/Makefile +2 -5

index 6dbb105..d8efad0 100644
@@ -141,11 +141,8 @@ $(OBJTREE)/MLO.byteswap: $(obj)u-boot-spl.bin
 	$(OBJTREE)/tools/mkimage -T omapimage -n byteswap \
 		-a $(CONFIG_SPL_TEXT_BASE) -d $< $@
 
-ifneq ($(CONFIG_IMX_CONFIG),)
-$(OBJTREE)/SPL:	$(obj)u-boot-spl.bin
-	$(OBJTREE)/tools/mkimage -n  $(SRCTREE)/$(CONFIG_IMX_CONFIG) -T imximage \
-		-e $(CONFIG_SPL_TEXT_BASE) -d $< $@
-endif
+$(OBJTREE)/SPL : $(obj)u-boot-spl.bin depend
+		$(MAKE) -C $(SRCTREE)/arch/arm/imx-common $@
 
 ALL-y	+= $(obj)u-boot-spl.bin

Signature · 1 line

1.7.9.5

Stefano Babic

2013-01-23 10:05 UTC #14 lore raw

PATCH v3 1/1 imximage.cfg: run files through C preprocessor

Quoted 9 lines · Troy Kisky

The '#' used as comments in the files cause the preprocessor trouble, so change to /* */.
The mkimage command which uses this preprocessor output was moved to arch/arm/imx-common/Makefile
.gitignore was updated to ignore .cfgtmp files.
Signed-off-by Troy Kisky <[email protected]>

Quoted 8 lines

---
v2: moved the mkimage call to arch/arm/imx-common Makefile updated spl/Makefile as well
added board/woodburn/imximage.cfg conversion
v3: added .gitignore to commit message
added mkimage command move to commit message
---

Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

Signature · 5 lines

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================