Skip to contentSkip to conversation

r8169: Remove firmware code

PATCH In review Hayes Wang 3 participants 12 messages Feb 6, 2013 – Feb 7, 2013

Subsystems (3)
lore
Share & tools
lore

Hayes Wang

author
#0 lore raw

PATCH 1/5 r8169: Remove firmware code

Some codes are belong to binary codes and should be removed.

---
 drivers/net/ethernet/realtek/r8169.c | 26 --------------------------
 1 file changed, 26 deletions(-)
drivers/net/ethernet/realtek/r8169.c +0 -26
index 1170232..e811ab5 100644
@@ -3408,32 +3408,6 @@ static void rtl8411_hw_phy_config(struct rtl8169_private *tp)
 
 static void rtl8168g_1_hw_phy_config(struct rtl8169_private *tp)
 {
-	static const u16 mac_ocp_patch[] = {
-		0xe008, 0xe01b, 0xe01d, 0xe01f,
-		0xe021, 0xe023, 0xe025, 0xe027,
-		0x49d2, 0xf10d, 0x766c, 0x49e2,
-		0xf00a, 0x1ec0, 0x8ee1, 0xc60a,
-
-		0x77c0, 0x4870, 0x9fc0, 0x1ea0,
-		0xc707, 0x8ee1, 0x9d6c, 0xc603,
-		0xbe00, 0xb416, 0x0076, 0xe86c,
-		0xc602, 0xbe00, 0x0000, 0xc602,
-
-		0xbe00, 0x0000, 0xc602, 0xbe00,
-		0x0000, 0xc602, 0xbe00, 0x0000,
-		0xc602, 0xbe00, 0x0000, 0xc602,
-		0xbe00, 0x0000, 0xc602, 0xbe00,
-
-		0x0000, 0x0000, 0x0000, 0x0000
-	};
-	u32 i;
-
-	/* Patch code for GPHY reset */
-	for (i = 0; i < ARRAY_SIZE(mac_ocp_patch); i++)
-		r8168_mac_ocp_write(tp, 0xf800 + 2*i, mac_ocp_patch[i]);
-	r8168_mac_ocp_write(tp, 0xfc26, 0x8000);
-	r8168_mac_ocp_write(tp, 0xfc28, 0x0075);
-
 	rtl_apply_firmware(tp);
 
 	if (r8168_phy_ocp_read(tp, 0xa460) & 0x0100)
Signature · 1 line
1.8.1
author
#1 lore raw

PATCH 2/5 r8169: Update PHY settings of RTL8111G

- Replace the current settings with rtl_writephy and rtl_readphy. For the hardware, the settings are same with previous ones. This make the setting method like the previous chips.
- Add new PHY settings.

---
 drivers/net/ethernet/realtek/r8169.c | 72 +++++++++++++++++++++++++-----------
 1 file changed, 51 insertions(+), 21 deletions(-)
drivers/net/ethernet/realtek/r8169.c +51 -21
index e811ab5..d1bee4c 100644
@@ -1029,14 +1029,6 @@ static u16 r8168_phy_ocp_read(struct rtl8169_private *tp, u32 reg)
 		(RTL_R32(GPHY_OCP) & 0xffff) : ~0;
 }
 
-static void rtl_w1w0_phy_ocp(struct rtl8169_private *tp, int reg, int p, int m)
-{
-	int val;
-
-	val = r8168_phy_ocp_read(tp, reg);
-	r8168_phy_ocp_write(tp, reg, (val | p) & ~m);
-}
-
 static void r8168_mac_ocp_write(struct rtl8169_private *tp, u32 reg, u32 data)
 {
 	void __iomem *ioaddr = tp->mmio_addr;
@@ -3410,23 +3402,61 @@ static void rtl8168g_1_hw_phy_config(struct rtl8169_private *tp)
 {
 	rtl_apply_firmware(tp);
 
-	if (r8168_phy_ocp_read(tp, 0xa460) & 0x0100)
-		rtl_w1w0_phy_ocp(tp, 0xbcc4, 0x0000, 0x8000);
-	else
-		rtl_w1w0_phy_ocp(tp, 0xbcc4, 0x8000, 0x0000);
+	rtl_writephy(tp, 0x1f, 0x0a46);
+	if (rtl_readphy(tp, 0x10) & 0x0100) {
+		rtl_writephy(tp, 0x1f, 0x0bcc);
+		rtl_w1w0_phy(tp, 0x12, 0x0000, 0x8000);
+	} else {
+		rtl_writephy(tp, 0x1f, 0x0bcc);
+		rtl_w1w0_phy(tp, 0x12, 0x8000, 0x0000);
+	}
 
-	if (r8168_phy_ocp_read(tp, 0xa466) & 0x0100)
-		rtl_w1w0_phy_ocp(tp, 0xc41a, 0x0002, 0x0000);
-	else
-		rtl_w1w0_phy_ocp(tp, 0xbcc4, 0x0000, 0x0002);
+	rtl_writephy(tp, 0x1f, 0x0a46);
+	if (rtl_readphy(tp, 0x13) & 0x0100) {
+		rtl_writephy(tp, 0x1f, 0x0c41);
+		rtl_w1w0_phy(tp, 0x15, 0x0002, 0x0000);
+	} else {
+		rtl_writephy(tp, 0x1f, 0x0c41);
+		rtl_w1w0_phy(tp, 0x15, 0x0000, 0x0002);
+	}
 
-	rtl_w1w0_phy_ocp(tp, 0xa442, 0x000c, 0x0000);
-	rtl_w1w0_phy_ocp(tp, 0xa4b2, 0x0004, 0x0000);
+	/* Enable PHY auto speed down */
+	rtl_writephy(tp, 0x1f, 0x0a44);
+	rtl_w1w0_phy(tp, 0x11, 0x000c, 0x0000);
+
+	rtl_writephy(tp, 0x1f, 0x0bcc);
+	rtl_w1w0_phy(tp, 0x14, 0x0100, 0x0000);
+	rtl_writephy(tp, 0x1f, 0x0a44);
+	rtl_w1w0_phy(tp, 0x11, 0x00c0, 0x0000);
+	rtl_writephy(tp, 0x1f, 0x0a43);
+	rtl_writephy(tp, 0x13, 0x8084);
+	rtl_w1w0_phy(tp, 0x14, 0x0000, 0x6000);
+	rtl_w1w0_phy(tp, 0x10, 0x1003, 0x0000);
+
+	/* EEE auto-fallback function */
+	rtl_writephy(tp, 0x1f, 0x0a4b);
+	rtl_w1w0_phy(tp, 0x11, 0x0004, 0x0000);
+
+	/* Enable UC LPF tune function */
+	rtl_writephy(tp, 0x1f, 0x0a43);
+	rtl_writephy(tp, 0x13, 0x8012);
+	rtl_w1w0_phy(tp, 0x14, 0x8000, 0x0000);
+
+	rtl_writephy(tp, 0x1f, 0x0c42);
+	rtl_w1w0_phy(tp, 0x11, 0x4000, 0x2000);
 
-	r8168_phy_ocp_write(tp, 0xa436, 0x8012);
-	rtl_w1w0_phy_ocp(tp, 0xa438, 0x8000, 0x0000);
+	/* Improve SWR Efficiency */
+	rtl_writephy(tp, 0x1f, 0x0bcd);
+	rtl_writephy(tp, 0x14, 0x5065);
+	rtl_writephy(tp, 0x14, 0xd065);
+	rtl_writephy(tp, 0x1f, 0x0bc8);
+	rtl_writephy(tp, 0x11, 0x5655);
+	rtl_writephy(tp, 0x1f, 0x0bcd);
+	rtl_writephy(tp, 0x14, 0x1065);
+	rtl_writephy(tp, 0x14, 0x9065);
+	rtl_writephy(tp, 0x14, 0x1065);
 
-	rtl_w1w0_phy_ocp(tp, 0xc422, 0x4000, 0x2000);
+	rtl_writephy(tp, 0x1f, 0x0000);
 }
 
 static void rtl8102e_hw_phy_config(struct rtl8169_private *tp)
Signature · 1 line
1.8.1
author
#2 lore raw

PATCH 3/5 r8169: Modify the method for setting firmware

In reply to Hayes Wang

Remove useless action PHY_READ_EFUSE, and define the new action PHY_MDIO_CHG.

PHY_MDIO_CHG is used to modify the mdio operation. By the way, the firmware could support setting mac ocp.

---
 drivers/net/ethernet/realtek/r8169.c | 36 ++++++++++++++++++++++++++++++++----
 1 file changed, 32 insertions(+), 4 deletions(-)
drivers/net/ethernet/realtek/r8169.c +32 -4
index d1bee4c..55a7fb5 100644
@@ -1074,6 +1074,21 @@ static int r8168g_mdio_read(struct rtl8169_private *tp, int reg)
 	return r8168_phy_ocp_read(tp, tp->ocp_base + reg * 2);
 }
 
+static void mac_mcu_write(struct rtl8169_private *tp, int reg, int value)
+{
+	if (reg == 0x1f) {
+		tp->ocp_base = value << 4;
+		return;
+	}
+
+	r8168_mac_ocp_write(tp, tp->ocp_base + reg, value);
+}
+
+static int mac_mcu_read(struct rtl8169_private *tp, int reg)
+{
+	return r8168_mac_ocp_read(tp, tp->ocp_base + reg);
+}
+
 DECLARE_RTL_COND(rtl_phyar_cond)
 {
 	void __iomem *ioaddr = tp->mmio_addr;
@@ -2139,7 +2154,7 @@ static void rtl_writephy_batch(struct rtl8169_private *tp,
 #define PHY_DATA_OR		0x10000000
 #define PHY_DATA_AND		0x20000000
 #define PHY_BJMPN		0x30000000
-#define PHY_READ_EFUSE		0x40000000
+#define PHY_MDIO_CHG		0x40000000
 #define PHY_READ_MAC_BYTE	0x50000000
 #define PHY_WRITE_MAC_BYTE	0x60000000
 #define PHY_CLEAR_READCOUNT	0x70000000
@@ -2227,7 +2242,7 @@ static bool rtl_fw_data_ok(struct rtl8169_private *tp, struct net_device *dev,
 		case PHY_READ:
 		case PHY_DATA_OR:
 		case PHY_DATA_AND:
-		case PHY_READ_EFUSE:
+		case PHY_MDIO_CHG:
 		case PHY_CLEAR_READCOUNT:
 		case PHY_WRITE:
 		case PHY_WRITE_PREVIOUS:
@@ -2291,10 +2306,13 @@ out:
 static void rtl_phy_write_fw(struct rtl8169_private *tp, struct rtl_fw *rtl_fw)
 {
 	struct rtl_fw_phy_action *pa = &rtl_fw->phy_action;
+	struct mdio_ops org, *ops = &tp->mdio_ops;
 	u32 predata, count;
 	size_t index;
 
 	predata = count = 0;
+	org.write = ops->write;
+	org.read = ops->read;
 
 	for (index = 0; index < pa->size; ) {
 		u32 action = le32_to_cpu(pa->code[index]);
@@ -2321,8 +2339,15 @@ static void rtl_phy_write_fw(struct rtl8169_private *tp, struct rtl_fw *rtl_fw)
 		case PHY_BJMPN:
 			index -= regno;
 			break;
-		case PHY_READ_EFUSE:
-			predata = rtl8168d_efuse_read(tp, regno);
+		case PHY_MDIO_CHG:
+			if (data == 0) {
+				ops->write = org.write;
+				ops->read = org.read;
+			} else if (data == 1) {
+				ops->write = mac_mcu_write;
+				ops->read = mac_mcu_read;
+			}
+
 			index++;
 			break;
 		case PHY_CLEAR_READCOUNT:
@@ -2365,6 +2390,9 @@ static void rtl_phy_write_fw(struct rtl8169_private *tp, struct rtl_fw *rtl_fw)
 			BUG();
 		}
 	}
+
+	ops->write = org.write;
+	ops->read = org.read;
 }
 
 static void rtl_release_firmware(struct rtl8169_private *tp)
Signature · 1 line
1.8.1
#3 lore raw

Re: [PATCH 3/5] r8169: Modify the method for setting firmware

Hayes Wang <[email protected]> :

Quoted 6 lines

Remove useless action PHY_READ_EFUSE, and define the new action PHY_MDIO_CHG.

PHY_MDIO_CHG is used to modify the mdio operation. By the way, the firmware could support setting mac ocp.

[...]

Quoted 4 lines
drivers/net/ethernet/realtek/r8169.c +0 -0
index d1bee4c..55a7fb5 100644

[...]

Quoted 4 lines
drivers/net/ethernet/realtek/r8169.c +0 -0
@@ -2321,8 +2339,15 @@ static void rtl_phy_write_fw(struct rtl8169_private *tp, struct rtl_fw *rtl_fw)
 		case PHY_BJMPN:
 			index -= regno;
 			break;

drivers/net/ethernet/realtek/r8169.c static void rtl_phy_write_fw(struct rtl8169_private *tp, struct rtl_fw *rtl_fw) · line 2349

Quoted 10 lines
drivers/net/ethernet/realtek/r8169.c +8 -2
-		case PHY_READ_EFUSE:
-			predata = rtl8168d_efuse_read(tp, regno);
+		case PHY_MDIO_CHG:
+			if (data == 0) {
+				ops->write = org.write;
+				ops->read = org.read;
+			} else if (data == 1) {
+				ops->write = mac_mcu_write;
+				ops->read = mac_mcu_read;
+			}

Did you check that none of rtl_nic/rtl8168d-{1, 2}.fw uses PHY_READ_EFUSE ?

Signature · 1 line
Ueimor
author
#4 lore raw

RE: [PATCH 3/5] r8169: Modify the method for setting firmware

Francois Romieu [mailto:[email protected]]
[...]

Quoted 4 lines

Did you check that none of rtl_nic/rtl8168d-{1, 2}.fw uses PHY_READ_EFUSE ?

I have made sure that none of the current firmwares use PHY_READ_EFUSE.

Best Regards,
Hayes

author
#5 lore raw

PATCH 4/5 r8169: Update the RTL8111G parameters

In reply to Hayes Wang

- replace rtl8168g-1.fw with rtl8168g-2.fw which support new method.
- fix PHY power down is useless.
- disable rx early which causes the rx abnormal.
- fix the conflict between jumbo frame and flow control.

---
 drivers/net/ethernet/realtek/r8169.c | 18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)
drivers/net/ethernet/realtek/r8169.c +16 -2
index 55a7fb5..c25a329 100644
@@ -47,7 +47,7 @@
 #define FIRMWARE_8402_1		"rtl_nic/rtl8402-1.fw"
 #define FIRMWARE_8411_1		"rtl_nic/rtl8411-1.fw"
 #define FIRMWARE_8106E_1	"rtl_nic/rtl8106e-1.fw"
-#define FIRMWARE_8168G_1	"rtl_nic/rtl8168g-1.fw"
+#define FIRMWARE_8168G_1	"rtl_nic/rtl8168g-2.fw"
 
 #ifdef RTL8169_DEBUG
 #define assert(expr) \
@@ -329,6 +329,7 @@ enum rtl_registers {
 #define	RXCFG_FIFO_SHIFT		13
 					/* No threshold before first PCI xfer */
 #define	RX_FIFO_THRESH			(7 << RXCFG_FIFO_SHIFT)
+#define	RX_EARLY_OFF			(1 << 11)
 #define	RXCFG_DMA_SHIFT			8
 					/* Unlimited maximum PCI burst. */
 #define	RX_DMA_BURST			(7 << RXCFG_DMA_SHIFT)
@@ -4077,6 +4078,10 @@ static void r8168_pll_power_down(struct rtl8169_private *tp)
 	case RTL_GIGA_MAC_VER_33:
 		RTL_W8(PMCH, RTL_R8(PMCH) & ~0x80);
 		break;
+	case RTL_GIGA_MAC_VER_40:
+	case RTL_GIGA_MAC_VER_41:
+		RTL_W8(PMCH, RTL_R8(PMCH) & ~0x40);
+		break;
 	}
 }
 
@@ -4094,6 +4099,10 @@ static void r8168_pll_power_up(struct rtl8169_private *tp)
 	case RTL_GIGA_MAC_VER_33:
 		RTL_W8(PMCH, RTL_R8(PMCH) | 0x80);
 		break;
+	case RTL_GIGA_MAC_VER_40:
+	case RTL_GIGA_MAC_VER_41:
+		RTL_W8(PMCH, RTL_R8(PMCH) | 0x40);
+		break;
 	}
 
 	r8168_phy_power_up(tp);
@@ -4199,6 +4208,10 @@ static void rtl_init_rxcfg(struct rtl8169_private *tp)
 	case RTL_GIGA_MAC_VER_34:
 		RTL_W32(RxConfig, RX128_INT_EN | RX_MULTI_EN | RX_DMA_BURST);
 		break;
+	case RTL_GIGA_MAC_VER_40:
+	case RTL_GIGA_MAC_VER_41:
+		RTL_W32(RxConfig, RX128_INT_EN | RX_DMA_BURST | RX_EARLY_OFF);
+		break;
 	default:
 		RTL_W32(RxConfig, RX128_INT_EN | RX_DMA_BURST);
 		break;
@@ -5190,7 +5203,8 @@ static void rtl_hw_start_8168g_1(struct rtl8169_private *tp)
 	/* Adjust EEE LED frequency */
 	RTL_W8(EEE_LED, RTL_R8(EEE_LED) & ~0x07);
 
-	rtl_w1w0_eri(tp, 0x2fc, ERIAR_MASK_0001, 0x01, 0x02, ERIAR_EXGMAC);
+	rtl_w1w0_eri(tp, 0x2fc, ERIAR_MASK_0001, 0x01, 0x06, ERIAR_EXGMAC);
+	rtl_w1w0_eri(tp, 0x1b0, ERIAR_MASK_0011, 0x0000, 0x1000, ERIAR_EXGMAC);
 }
 
 static void rtl_hw_start_8168(struct net_device *dev)
Signature · 1 line
1.8.1
#6 lore raw

Re: [PATCH 4/5] r8169: Update the RTL8111G parameters

Hayes Wang <[email protected]> :

Quoted 6 lines

- replace rtl8168g-1.fw with rtl8168g-2.fw which support new method.
- fix PHY power down is useless.
- disable rx early which causes the rx abnormal.
- fix the conflict between jumbo frame and flow control.

It seems ok.

Signature · 1 line
Ueimor
author
#7 lore raw

PATCH 5/5 r8169: fix could not dump registers

In reply to Hayes Wang

For new version of Fedora and Ubuntu, we see all 0xff when dumping the hw regs through ethtool. Using a loop to read registers could fix it.

---
 drivers/net/ethernet/realtek/r8169.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/net/ethernet/realtek/r8169.c +5 -1
index c25a329..4ae3c55 100644
@@ -1880,12 +1880,16 @@ static void rtl8169_get_regs(struct net_device *dev, struct ethtool_regs *regs,
 			     void *p)
 {
 	struct rtl8169_private *tp = netdev_priv(dev);
+	void __iomem *ioaddr = tp->mmio_addr;
+	u32 *d = (u32 *)p;
+	int i;
 
 	if (regs->len > R8169_REGS_SIZE)
 		regs->len = R8169_REGS_SIZE;
 
 	rtl_lock_work(tp);
-	memcpy_fromio(p, tp->mmio_addr, regs->len);
+	for (i = 0; i < regs->len; i += 4)
+		*d++ = RTL_R32(i);
 	rtl_unlock_work(tp);
 }
 
Signature · 1 line
1.8.1
#8 lore raw

Re: [PATCH 5/5] r8169: fix could not dump registers

Hayes Wang <[email protected]> :

Quoted 3 lines

For new version of Fedora and Ubuntu, we see all 0xff when dumping the hw regs through ethtool. Using a loop to read registers could fix it.

/me wonders...

Will I be wrong if I reformulate so as to outline the role of 4 bytes aligned accesses when walking the registers area ?

Signature · 1 line
Ueimor
#10 lore raw

David Miller <[email protected]> :
[...]

Quoted 1 line

Francois please review this series, thanks.

It does not seem wrong but I'll give it a try before sending a pull request.

Signature · 1 line
Ueimor