Skip to contentSkip to conversation

mtd: nand: Introduce CONFIG_SYS_NAND_BUSWIDTH_16BIT

PATCH New Fabio Estevam 4 participants 10 messages Feb 26, 2013 – Feb 27, 2013

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 mtd: nand: Introduce CONFIG_SYS_NAND_BUSWIDTH_16BIT

Introduce CONFIG_SYS_NAND_BUSWIDTH_16BIT option so that other NAND controller drivers could use it when a 16-bit NAND is deployed.

drivers/mtd/nand/ndfc has CONFIG_SYS_NDFC_16BIT, so just rename it, so that other NAND drivers could reuse the same symbol.

---
Changes since v1:
- Improve README

 README                  |    9 ++++++---
 drivers/mtd/nand/ndfc.c |    4 ++--
 2 files changed, 8 insertions(+), 5 deletions(-)
README +6 -3
index d8cb394..bdd2c81 100644
@@ -3713,9 +3713,12 @@ Low Level (hardware related) configuration options:
 - CONFIG_SYS_SRIOn_MEM_SIZE:
 		Size of SRIO port 'n' memory region
 
-- CONFIG_SYS_NDFC_16
-		Defined to tell the NDFC that the NAND chip is using a
-		16 bit bus.
+- CONFIG_SYS_NAND_BUSWIDTH_16BIT
+		Defined to tell the NAND controller that the NAND chip is using
+ 		a 16 bit bus.
+		Not all NAND drivers use this symbol.
+		Example of driver that uses it:
+		- drivers/mtd/nand/ndfc.c
 
 - CONFIG_SYS_NDFC_EBC0_CFG
 		Sets the EBC0_CFG register for the NDFC. If not defined
drivers/mtd/nand/ndfc.c +2 -2
index 6ebbb5e..213d2c9 100644
@@ -156,7 +156,7 @@ static uint8_t ndfc_read_byte(struct mtd_info *mtd)
 
 	struct nand_chip *chip = mtd->priv;
 
-#ifdef CONFIG_SYS_NDFC_16BIT
+#ifdef CONFIG_SYS_NAND_BUSWIDTH_16BIT
 	return (uint8_t) readw(chip->IO_ADDR_R);
 #else
 	return readb(chip->IO_ADDR_R);
@@ -218,7 +218,7 @@ int board_nand_init(struct nand_chip *nand)
 	nand->ecc.bytes = 3;
 	nand->select_chip = ndfc_select_chip;
 
-#ifdef CONFIG_SYS_NDFC_16BIT
+#ifdef CONFIG_SYS_NAND_BUSWIDTH_16BIT
 	nand->options |= NAND_BUSWIDTH_16;
 #endif
 
Signature · 1 line
1.7.9.5
#1 lore raw

PATCH v2 2/2 mtd: nand: mxc_nand: Fix is_16bit_nand()

Currently is_16bit_nand() is a per SoC function and it decides the bus nand width by reading some boot related registers.

This method works when NAND is the boot medium, but does not work if another boot medium is used. For example: booting from a SD card and then using NAND to store the environment variables, would lead to the following error:

NAND bus width 16 instead 8 bit
No NAND device found!!!
0 MiB

Use CONFIG_SYS_NAND_BUSWIDTH_16BIT symbol to decide the bus width.

If it is defined in the board file, then consider 16-bit NAND bus-width, otherwise assume 8-bit NAND is used.

This also aligns with Documentation/devicetree/bindings/mtd/nand.txt, which states:

nand-bus-width : 8 or 16 bus width if not present 82

---
Changes since v1:
- Add an entry into README

 README                      |    3 ++-
 drivers/mtd/nand/mxc_nand.c |   37 +++----------------------------------
 2 files changed, 5 insertions(+), 35 deletions(-)
README +2 -1
index bdd2c81..1a6a7a5 100644
@@ -3717,8 +3717,9 @@ Low Level (hardware related) configuration options:
 		Defined to tell the NAND controller that the NAND chip is using
  		a 16 bit bus.
 		Not all NAND drivers use this symbol.
-		Example of driver that uses it:
+		Example of drivers that use it:
 		- drivers/mtd/nand/ndfc.c
+		- drivers/mtd/nand/mxc_nand.c
 
 - CONFIG_SYS_NDFC_EBC0_CFG
 		Sets the EBC0_CFG register for the NDFC. If not defined
drivers/mtd/nand/mxc_nand.c +3 -34
index d0ded48..bb475f2 100644
@@ -98,45 +98,14 @@ static struct nand_ecclayout nand_hw_eccoob2k = {
 #endif
 #endif
 
-#ifdef CONFIG_MX27
 static int is_16bit_nand(void)
 {
-	struct system_control_regs *sc_regs =
-		(struct system_control_regs *)IMX_SYSTEM_CTL_BASE;
-
-	if (readl(&sc_regs->fmcr) & NF_16BIT_SEL)
-		return 1;
-	else
-		return 0;
-}
-#elif defined(CONFIG_MX31)
-static int is_16bit_nand(void)
-{
-	struct clock_control_regs *sc_regs =
-		(struct clock_control_regs *)CCM_BASE;
-
-	if (readl(&sc_regs->rcsr) & CCM_RCSR_NF16B)
-		return 1;
-	else
-		return 0;
-}
-#elif defined(CONFIG_MX25) || defined(CONFIG_MX35)
-static int is_16bit_nand(void)
-{
-	struct ccm_regs *ccm = (struct ccm_regs *)IMX_CCM_BASE;
-
-	if (readl(&ccm->rcsr) & CCM_RCSR_NF_16BIT_SEL)
-		return 1;
-	else
-		return 0;
-}
+#if defined(CONFIG_SYS_NAND_BUSWIDTH_16BIT)
+	return 1;
 #else
-#warning "8/16 bit NAND autodetection not supported"
-static int is_16bit_nand(void)
-{
 	return 0;
-}
 #endif
+}
 
 static uint32_t *mxc_nand_memcpy32(uint32_t *dest, uint32_t *source, size_t size)
 {
Signature · 1 line
1.7.9.5
#2 lore raw

PATCH v2 2/2 mtd: nand: mxc_nand: Fix is_16bit_nand()

Hi Fabio,

Quoted 97 lines · Fabio Estevam

Currently is_16bit_nand() is a per SoC function and it decides the bus nand width by reading some boot related registers.

This method works when NAND is the boot medium, but does not work if another boot medium is used. For example: booting from a SD card and then using NAND to store the environment variables, would lead to the following error:

NAND bus width 16 instead 8 bit
No NAND device found!!!
0 MiB

Use CONFIG_SYS_NAND_BUSWIDTH_16BIT symbol to decide the bus width.

If it is defined in the board file, then consider 16-bit NAND bus-width, otherwise assume 8-bit NAND is used.

This also aligns with Documentation/devicetree/bindings/mtd/nand.txt, which states:

nand-bus-width : 8 or 16 bus width if not present 82

---
Changes since v1:
- Add an entry into README

 README                      |    3 ++-
 drivers/mtd/nand/mxc_nand.c |   37 +++----------------------------------
 2 files changed, 5 insertions(+), 35 deletions(-)
README +2 -1
index bdd2c81..1a6a7a5 100644
@@ -3717,8 +3717,9 @@ Low Level (hardware related) configuration options:
 		Defined to tell the NAND controller that the NAND chip is using
  		a 16 bit bus.
 		Not all NAND drivers use this symbol.
-		Example of driver that uses it:
+		Example of drivers that use it:
 		- drivers/mtd/nand/ndfc.c
+		- drivers/mtd/nand/mxc_nand.c
 
 - CONFIG_SYS_NDFC_EBC0_CFG
 		Sets the EBC0_CFG register for the NDFC. If not defined
drivers/mtd/nand/mxc_nand.c +3 -34
index d0ded48..bb475f2 100644
@@ -98,45 +98,14 @@ static struct nand_ecclayout nand_hw_eccoob2k = {
 #endif
 #endif
 
-#ifdef CONFIG_MX27
 static int is_16bit_nand(void)
 {
-	struct system_control_regs *sc_regs =
-		(struct system_control_regs *)IMX_SYSTEM_CTL_BASE;
-
-	if (readl(&sc_regs->fmcr) & NF_16BIT_SEL)
-		return 1;
-	else
-		return 0;
-}
-#elif defined(CONFIG_MX31)
-static int is_16bit_nand(void)
-{
-	struct clock_control_regs *sc_regs =
-		(struct clock_control_regs *)CCM_BASE;
-
-	if (readl(&sc_regs->rcsr) & CCM_RCSR_NF16B)
-		return 1;
-	else
-		return 0;
-}
-#elif defined(CONFIG_MX25) || defined(CONFIG_MX35)
-static int is_16bit_nand(void)
-{
-	struct ccm_regs *ccm = (struct ccm_regs *)IMX_CCM_BASE;
-
-	if (readl(&ccm->rcsr) & CCM_RCSR_NF_16BIT_SEL)
-		return 1;
-	else
-		return 0;
-}
+#if defined(CONFIG_SYS_NAND_BUSWIDTH_16BIT)
+	return 1;
 #else
-#warning "8/16 bit NAND autodetection not supported"
-static int is_16bit_nand(void)
-{
 	return 0;
-}
 #endif
+}
 
 static uint32_t *mxc_nand_memcpy32(uint32_t *dest, uint32_t *source, size_t
 size)
Quoted 1 line

{

That's correct.

is_16bit_nand() is only used to conditionally set NAND_BUSWIDTH_16 in this->options, then this flag is tested everywhere else, so we could also completely drop is_16bit_nand() and just do:

#ifdef CONFIG_SYS_NAND_BUSWIDTH_16BIT
	this->options |= NAND_BUSWIDTH_16;

#endif

What do you think is better? I'm fine with your implementation.

Should I rebase my series on that, keeping both series separate, or should I integrate these 2 patches as is at the beginning of my series?

Best regards,
Beno?t

reviewer
#3 lore raw

PATCH v2 2/2 mtd: nand: mxc_nand: Fix is_16bit_nand()

Quoted 8 lines · Beno?t Th?baudeau

That's correct.

is_16bit_nand() is only used to conditionally set NAND_BUSWIDTH_16 in this->options, then this flag is tested everywhere else, so we could also completely drop is_16bit_nand() and just do:

#ifdef CONFIG_SYS_NAND_BUSWIDTH_16BIT
        this->options |= NAND_BUSWIDTH_16;

#endif

Yes, this could be done.

Quoted 2 lines

What do you think is better? I'm fine with your implementation.

My main goal with this patch series was to fix a bug, and I think I can do as you suggest, and get rid of is_16bit_nand() in a future patch.

Quoted 2 lines

Should I rebase my series on that, keeping both series separate, or should I integrate these 2 patches as is at the beginning of my series?

I would say that you could send this series as is at the beginning of your next version in order to avoid conflicts.

Thanks,

Fabio Estevam

#4 lore raw

PATCH v2 2/2 mtd: nand: mxc_nand: Fix is_16bit_nand()

In reply to Fabio Estevam

Hi Fabio,

Le Tue, 26 Feb 2013 15:35:20 -0300,
Fabio Estevam <[email protected]> a ?crit :

Quoted 13 lines

Currently is_16bit_nand() is a per SoC function and it decides the bus nand width by reading some boot related registers.

This method works when NAND is the boot medium, but does not work if another boot medium is used. For example: booting from a SD card and then using NAND to store the environment variables, would lead to the following error:

NAND bus width 16 instead 8 bit
No NAND device found!!!
0 MiB

Use CONFIG_SYS_NAND_BUSWIDTH_16BIT symbol to decide the bus width.

Quoted 8 lines

If it is defined in the board file, then consider 16-bit NAND bus-width, otherwise assume 8-bit NAND is used.

This also aligns with Documentation/devicetree/bindings/mtd/nand.txt, which states:

nand-bus-width : 8 or 16 bus width if not present 82

are you sure that your patch won't break current boards booting on nand flash (and so which can use the current functions to detect the nand width) ?

Eric

#5 lore raw

PATCH v2 2/2 mtd: nand: mxc_nand: Fix is_16bit_nand()

Hi Eric,

Quoted 23 lines · Eric B?nard

Hi Fabio,

Le Tue, 26 Feb 2013 15:35:20 -0300,
Fabio Estevam <[email protected]> a ?crit :

Quoted 18 lines

Currently is_16bit_nand() is a per SoC function and it decides the bus nand width by reading some boot related registers.

This method works when NAND is the boot medium, but does not work if another
boot medium is used. For example: booting from a SD card and then using NAND
to store the environment variables, would lead to the following error:

NAND bus width 16 instead 8 bit
No NAND device found!!!
0 MiB

Use CONFIG_SYS_NAND_BUSWIDTH_16BIT symbol to decide the bus width.

If it is defined in the board file, then consider 16-bit NAND bus-width, otherwise assume 8-bit NAND is used.

Quoted 8 lines
Quoted 5 lines

This also aligns with Documentation/devicetree/bindings/mtd/nand.txt, which states:

nand-bus-width : 8 or 16 bus width if not present 82

are you sure that your patch won't break current boards booting on nand flash (and so which can use the current functions to detect the nand width) ?

This code is not used for NAND boot, for which the SPL version of this driver and CONFIG_SYS_NAND_BUSWIDTH_16 are used.

Best regards,
Beno?t

#6 lore raw

PATCH v2 2/2 mtd: nand: mxc_nand: Fix is_16bit_nand()

Hi Beno?t,

Le Wed, 27 Feb 2013 13:53:10 +0100 (CET),
Beno?t Th?baudeau <[email protected]> a ?crit :

Quoted 4 lines

This code is not used for NAND boot, for which the SPL version of this driver and CONFIG_SYS_NAND_BUSWIDTH_16 are used.

I didn't follow SPL migration (I have to come back to it so the next question may be stupid sorry in advance) but once u-boot is running isn't it using the "standard" driver and no more the SPL one ?

Eric

#7 lore raw

PATCH v2 2/2 mtd: nand: mxc_nand: Fix is_16bit_nand()

Hi Eric,

Quoted 5 lines · Eric B?nard

Hi Beno?t,

Le Wed, 27 Feb 2013 13:53:10 +0100 (CET),
Beno?t Th?baudeau <[email protected]> a ?crit :

Quoted 1 line
Quoted 7 lines
Quoted 4 lines

This code is not used for NAND boot, for which the SPL version of this driver
and CONFIG_SYS_NAND_BUSWIDTH_16 are used.

I didn't follow SPL migration (I have to come back to it so the next question may be stupid sorry in advance) but once u-boot is running isn't it using the "standard" driver and no more the SPL one ?

Yes, that's correct (unless you need to access NAND only from SPL). But if any board booting from NAND had a 16-bit NAND, CONFIG_SYS_NAND_BUSWIDTH_16 would have to be defined, which no board does, so none of these boards needs CONFIG_SYS_NAND_BUSWIDTH_16BIT either. And the rest of the explanation is what Fabio has just said.

Best regards,
Beno?t

#8 lore raw

PATCH v2 2/2 mtd: nand: mxc_nand: Fix is_16bit_nand()

Hi Beno?t and Fabio,

Le Wed, 27 Feb 2013 14:40:51 +0100 (CET),
Beno?t Th?baudeau <[email protected]> a ?crit :

Quoted 14 lines · Eric B?nard
Quoted 5 lines

Hi Beno?t,

Le Wed, 27 Feb 2013 13:53:10 +0100 (CET),
Beno?t Th?baudeau <[email protected]> a ?crit :

Quoted 1 line
Quoted 7 lines
Quoted 4 lines

This code is not used for NAND boot, for which the SPL version of this driver
and CONFIG_SYS_NAND_BUSWIDTH_16 are used.

I didn't follow SPL migration (I have to come back to it so the next question may be stupid sorry in advance) but once u-boot is running isn't it using the "standard" driver and no more the SPL one ?

Quoted 6 lines

Yes, that's correct (unless you need to access NAND only from SPL). But if any board booting from NAND had a 16-bit NAND, CONFIG_SYS_NAND_BUSWIDTH_16 would have to be defined, which no board does, so none of these boards needs CONFIG_SYS_NAND_BUSWIDTH_16BIT either. And the rest of the explanation is what Fabio has just said.

thanks to both of you for the details.

Eric

reviewer
#9 lore raw

PATCH v2 2/2 mtd: nand: mxc_nand: Fix is_16bit_nand()

In reply to Eric Bénard

Hi Eric,

Quoted 3 lines · Eric B?nard

are you sure that your patch won't break current boards booting on nand flash (and so which can use the current functions to detect the nand width) ?

If a board is booting from NAND, then it is required that the boot jumpers are correctly set to specify NAND boot mode and the NAND type (8-bit versus 16-bit width, for example).

I revisited all the i.mx boards that use MXC_NAND driver and could not see anyone using 16-bit NAND (ie, no 16-bit NAND IOMUX setting), so it is safe to assume that all the current boards are using 8-bit width NAND.

If a board has 16-bit width NAND, then the boot jumpers need to reflect that and CONFIG_SYS_NAND_BUSWIDTH_16BIT must be specified in the config file.

So I don't envision any breakage here.

Regards,

Fabio Estevam