Zynq support for barebox
Subsystems (4)
cover Zynq support for barebox
In San Francisco a couple weeks ago (ELC2013), Thomas Petazzoni informally mentioned barebox in passing, so I decided to toy with it a bit...
This patchset adds basic support for the Zynq SoC to barebox. So far, it's only been tested as a 'secondary' bootloader (after u-boot). Also added is support for the zc702 development board.
The first two patches are simple typos I found getting acclimated to the barebox source.
Josh Cartwright (5):
trivial: doc: fix typos in mach-arm.dox
defaultenv: fixed mismatched braces in bin/boot
ARM: zynq: add driver for Zynq uarts
ARM: zynq: add support for Zynq 7000 SoC
ARM: zynq: add support for zc702 development board
arch/arm/Kconfig | 9 + arch/arm/Makefile | 2 + arch/arm/boards/zynq-zc702/Makefile | 1 + arch/arm/boards/zynq-zc702/config.h | 0 arch/arm/boards/zynq-zc702/devices.c | 70 ++++++ arch/arm/boards/zynq-zc702/lowlevel.c | 28 +++ arch/arm/mach-arm.dox | 4 +- arch/arm/mach-zynq/Kconfig | 22 ++ arch/arm/mach-zynq/Makefile | 1 + arch/arm/mach-zynq/clocks.c | 341 +++++++++++++++++++++++++++++ arch/arm/mach-zynq/include/mach/clkdev.h | 7 + arch/arm/mach-zynq/include/mach/debug_ll.h | 21 ++ arch/arm/mach-zynq/include/mach/slcr.h | 26 +++ arch/arm/mach-zynq/reset.c | 28 +++ defaultenv/bin/boot | 2 +- drivers/serial/Kconfig | 6 + drivers/serial/Makefile | 1 + drivers/serial/serial_zynq.c | 144 ++++++++++++ 18 files changed, 710 insertions(+), 3 deletions(-) create mode 100644 arch/arm/boards/zynq-zc702/Makefile create mode 100644 arch/arm/boards/zynq-zc702/config.h create mode 100644 arch/arm/boards/zynq-zc702/devices.c create mode 100644 arch/arm/boards/zynq-zc702/lowlevel.c create mode 100644 arch/arm/mach-zynq/Kconfig create mode 100644 arch/arm/mach-zynq/Makefile create mode 100644 arch/arm/mach-zynq/clocks.c create mode 100644 arch/arm/mach-zynq/include/mach/clkdev.h create mode 100644 arch/arm/mach-zynq/include/mach/debug_ll.h create mode 100644 arch/arm/mach-zynq/include/mach/slcr.h create mode 100644 arch/arm/mach-zynq/reset.c create mode 100644 drivers/serial/serial_zynq.c
Signature · 7 lines
1.8.1.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH 1/5 trivial: doc: fix typos in mach-arm.dox
--- arch/arm/mach-arm.dox | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/mach-arm.dox +2 -2
@@ -12,7 +12,7 @@ FIXME to: "runtime address != link address". You should only use branches and do not refer to fixed data. This implies the use of assembler code only. -The ARM CPU starts at lable \<reset\> in one of the corresponding start-*.S +The ARM CPU starts at label \<reset\> in one of the corresponding start-*.S files. After some basic hardware setup it can call a function \<arch_init_lowlevel\> if not disabled. This call is intended to give all developers a chance to use a standard reset vector file, but also do some
@@ -47,7 +47,7 @@ Lets call the new MACH new_cpu. - add /arch/arm/mach-new_cpu/Makfile - add other CPU specific code into /arch/arm/mach-new_cpu/ - modify /arch/arm/Kconfig - - modify /arch/arm/Makfile + - modify /arch/arm/Makefile @section mach_arm_architecures Architectures using ARM processors For details on specific architectures:
Signature · 8 lines
1.8.1.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH 2/5 defaultenv: fixed mismatched braces in bin/boot
In reply to Josh CartwrightCommit 91b563613e5c831998210a2c500ec4d2492a650b ("dhcp: switch to global var support") introduced global dhcp variables, but there was a typo in the boot script, with a forgotten open brace. Fix it.
--- defaultenv/bin/boot | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
defaultenv/bin/boot +1 -1
@@ -50,7 +50,7 @@ if [ x$ip = xdhcp -o x$ip = "xdhcp-barebox" ]; then if [ x${global.dhcp.bootfile} != x ]; then kernelimage=${global.dhcp.bootfile} fi - if [ x$global.dhcp.oftree_file} != x ]; then + if [ x${global.dhcp.oftree_file} != x ]; then oftreeimage=${global.dhcp.oftree_file} fi fi
Signature · 8 lines
1.8.1.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH 3/5 ARM: zynq: add driver for Zynq uarts
In reply to Josh CartwrightSimple UART driver for Zynq SoCs, based loosely on the u-boot driver.
--- drivers/serial/Kconfig | 6 ++ drivers/serial/Makefile | 1 + drivers/serial/serial_zynq.c | 144 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 151 insertions(+) create mode 100644 drivers/serial/serial_zynq.c
drivers/serial/Kconfig +6 -0
@@ -113,4 +113,10 @@ config DRIVER_SERIAL_OMAP4_USBBOOT help Enable this to get console support over the usb bus used to boot an OMAP4 +config DRIVER_SERIAL_ZYNQ + bool "driver for Zynq uarts" + default n + help + Say Y here to get console out support with the Zynq uarts + endmenu
drivers/serial/Makefile +1 -0
@@ -21,3 +21,4 @@ obj-$(CONFIG_DRIVER_SERIAL_ALTERA) += serial_altera.o obj-$(CONFIG_DRIVER_SERIAL_ALTERA_JTAG) += serial_altera_jtag.o obj-$(CONFIG_DRIVER_SERIAL_PXA) += serial_pxa.o obj-$(CONFIG_DRIVER_SERIAL_OMAP4_USBBOOT) += serial_omap4_usbboot.o +obj-$(CONFIG_DRIVER_SERIAL_ZYNQ) += serial_zynq.o
drivers/serial/serial_zynq.c new file +144 -0
144 lines not on this page · raw message
Signature · 8 lines
1.8.1.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH 3/5] ARM: zynq: add driver for Zynq uarts
Quoted 91 lines · Josh Cartwright
Simple UART driver for Zynq SoCs, based loosely on the u-boot driver.
Signed-off-by Josh Cartwright <[email protected]>--- drivers/serial/Kconfig | 6 ++ drivers/serial/Makefile | 1 + drivers/serial/serial_zynq.c | 144 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 151 insertions(+) create mode 100644 drivers/serial/serial_zynq.cdrivers/serial/Kconfig +6
-0@@ -113,4 +113,10 @@ config DRIVER_SERIAL_OMAP4_USBBOOT help Enable this to get console support over the usb bus used to boot an OMAP4 +config DRIVER_SERIAL_ZYNQ + bool "driver for Zynq uarts" + default n + help + Say Y here to get console out support with the Zynq uarts + endmenudrivers/serial/Makefile +1
-0@@ -21,3 +21,4 @@ obj-$(CONFIG_DRIVER_SERIAL_ALTERA) += serial_altera.o obj-$(CONFIG_DRIVER_SERIAL_ALTERA_JTAG) += serial_altera_jtag.o obj-$(CONFIG_DRIVER_SERIAL_PXA) += serial_pxa.o obj-$(CONFIG_DRIVER_SERIAL_OMAP4_USBBOOT) += serial_omap4_usbboot.o +obj-$(CONFIG_DRIVER_SERIAL_ZYNQ) += serial_zynq.odrivers/serial/serial_zynq.c new file +51
-0@@ -0,0 +1,144 @@ +/* +* (C) Copyright 2013 Josh Cartwright +* +* Based very loosely on u-boot drivers/serial/serial_zynq.c. +* +* Copyright (C) 2012 Michal Simek <[email protected]> +* Copyright (C) 2011-2012 Xilinx, Inc. All rights reserved. +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ +#include <common.h> +#include <io.h> +#include <init.h> +#include <driver.h> +#include <xfuncs.h> +#include <console.h> +#include <malloc.h> + +#include <linux/clk.h> + +#define UART_CR 0x00000000 +#define UART_CR_TXEN (1<<4) +#define UART_CR_RXEN (1<<2) +#define UART_CR_TXRST (1<<1) +#define UART_CR_RXRST (1<<0) + +#define UART_SR 0x0000002C +#define UART_SR_TXFULL (1<<4) +#define UART_SR_TXEMPTY (1<<3) +#define UART_SR_RXFULL (1<<2) +#define UART_SR_RXEMPTY (1<<1) + +#define UART_FIFO 0x00000030 + +struct zynq_serial_device {
drivers/serial/serial_zynq.c line 61
Quoted 10 lines
drivers/serial/serial_zynq.c new file +10
-0+struct console_device cdev; +struct clk *clk; +void __iomem *regs; +}; + +#define to_zynq_device (p) container_of(p, struct zynq_serial_device, cdev) + +static void zynq_serial_init_device (struct zynq_serial_device *dev) +{ + writel(UART_CR_TXEN | UART_CR_RXEN | UART_CR_TXEN | UART_CR_RXEN,
IMHO there are too many 'UART_CR_TXEN' and 'UART_CR_RXEN' here.
Quoted 92 lines
drivers/serial/serial_zynq.c new file +83
-1+ dev->regs + UART_CR); +} + +static int zynq_serial_tstc (struct console_device *cdev) +{ +struct zynq_serial_device *zynq =to_zynq_device (cdev); + +return !(readl (zynq->regs +UART_SR ) &UART_SR_RXEMPTY ); +} + +static void zynq_serial_putc (struct console_device *cdev,char c) +{ +struct zynq_serial_device *zynq =to_zynq_device (cdev); + +while (readl (zynq->regs +UART_SR ) &UART_SR_TXFULL ); + +writel (c, zynq->regs +UART_FIFO ); +} + +static int zynq_serial_getc (struct console_device *cdev) +{ +struct zynq_serial_device *zynq =to_zynq_device (cdev); + +return readl (zynq->regs +UART_FIFO ); +} + +static void zynq_serial_flush (struct console_device *cdev) +{ +struct zynq_serial_device *zynq =to_zynq_device (cdev); + +while (!(readl (zynq->regs +UART_SR ) &UART_SR_TXEMPTY )); +} + +static int zynq_serial_probe (struct device_d *dev) +{ +struct zynq_serial_device *priv; +struct console_device *cdev; +int err; + + priv =xzalloc (sizeof (*priv)); + cdev = &priv->cdev; + + priv->regs =dev_request_mem_region (dev,0 ); + cdev->dev = dev; + cdev->f_caps =CONSOLE_STDIN |CONSOLE_STDOUT |CONSOLE_STDERR ; + cdev->tstc = zynq_serial_tstc; + cdev->putc = zynq_serial_putc; + cdev->getc = zynq_serial_getc; + cdev->flush = zynq_serial_flush; + + priv->clk =clk_get (dev,NULL ); + + err =clk_enable (priv->clk); +if (err) { +free (priv); +return err; + } + +zynq_serial_init_device (priv); + + dev->priv = priv; + +return console_register (cdev); +} + +static void zynq_serial_remove (struct device_d *dev) +{ +struct zynq_serial_device *zynq = dev->priv; +clk_disable (zynq->clk); +free (zynq); +} + +static struct driver_d zynq_serial_driver = { + .name ="zynq_serial" , + .probe = zynq_serial_probe, + .remove = zynq_serial_remove, +}; + +static int zynq_serial_init (void ) +{ +return platform_driver_register (&zynq_serial_driver); +} +console_initcall (zynq_serial_init); --1.8.1.2
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Signature · 7 lines
Best regards, Antony Pavlov _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH 3/5] ARM: zynq: add driver for Zynq uarts
Quoted 97 lines · Antony Pavlov
Quoted 96 lines · Josh Cartwright
Simple UART driver for Zynq SoCs, based loosely on the u-boot driver.
Signed-off-by Josh Cartwright <[email protected]>--- drivers/serial/Kconfig | 6 ++ drivers/serial/Makefile | 1 + drivers/serial/serial_zynq.c | 144 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 151 insertions(+) create mode 100644 drivers/serial/serial_zynq.cdrivers/serial/Kconfig +6
-0@@ -113,4 +113,10 @@ config DRIVER_SERIAL_OMAP4_USBBOOT help Enable this to get console support over the usb bus used to boot an OMAP4 +config DRIVER_SERIAL_ZYNQ + bool "driver for Zynq uarts" + default n + help + Say Y here to get console out support with the Zynq uarts + endmenudrivers/serial/Makefile +1
-0@@ -21,3 +21,4 @@ obj-$(CONFIG_DRIVER_SERIAL_ALTERA) += serial_altera.o obj-$(CONFIG_DRIVER_SERIAL_ALTERA_JTAG) += serial_altera_jtag.o obj-$(CONFIG_DRIVER_SERIAL_PXA) += serial_pxa.o obj-$(CONFIG_DRIVER_SERIAL_OMAP4_USBBOOT) += serial_omap4_usbboot.o +obj-$(CONFIG_DRIVER_SERIAL_ZYNQ) += serial_zynq.odrivers/serial/serial_zynq.c new file +56
-0@@ -0,0 +1,144 @@ +/* +* (C) Copyright 2013 Josh Cartwright +* +* Based very loosely on u-boot drivers/serial/serial_zynq.c. +* +* Copyright (C) 2012 Michal Simek <[email protected]> +* Copyright (C) 2011-2012 Xilinx, Inc. All rights reserved. +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ +#include <common.h> +#include <io.h> +#include <init.h> +#include <driver.h> +#include <xfuncs.h> +#include <console.h> +#include <malloc.h> + +#include <linux/clk.h> + +#define UART_CR 0x00000000 +#define UART_CR_TXEN (1<<4) +#define UART_CR_RXEN (1<<2) +#define UART_CR_TXRST (1<<1) +#define UART_CR_RXRST (1<<0) + +#define UART_SR 0x0000002C +#define UART_SR_TXFULL (1<<4) +#define UART_SR_TXEMPTY (1<<3) +#define UART_SR_RXFULL (1<<2) +#define UART_SR_RXEMPTY (1<<1) + +#define UART_FIFO 0x00000030 + +struct zynq_serial_device { +struct console_device cdev; +struct clk *clk; +void __iomem *regs; +}; +
Quoted 8 lines
drivers/serial/serial_zynq.c line 61
Quoted 5 lines
drivers/serial/serial_zynq.c new file +5
-0+#define to_zynq_device (p) container_of(p, struct zynq_serial_device, cdev) + +static void zynq_serial_init_device (struct zynq_serial_device *dev) +{ + writel(UART_CR_TXEN | UART_CR_RXEN | UART_CR_TXEN | UART_CR_RXEN,IMHO there are too many '
UART_CR_TXEN' and 'UART_CR_RXEN' here.
Yes indeed, thanks.
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH 3/5] ARM: zynq: add driver for Zynq uarts
In reply to Josh CartwrightQuoted 143 lines · Josh Cartwright
Simple UART driver for Zynq SoCs, based loosely on the u-boot driver.
Signed-off-by Josh Cartwright <[email protected]>--- drivers/serial/Kconfig | 6 ++ drivers/serial/Makefile | 1 + drivers/serial/serial_zynq.c | 144 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 151 insertions(+) create mode 100644 drivers/serial/serial_zynq.cdrivers/serial/Kconfig +6
-0@@ -113,4 +113,10 @@ config DRIVER_SERIAL_OMAP4_USBBOOT help Enable this to get console support over the usb bus used to boot an OMAP4 +config DRIVER_SERIAL_ZYNQ + bool "driver for Zynq uarts" + default n + help + Say Y here to get console out support with the Zynq uarts + endmenudrivers/serial/Makefile +1
-0@@ -21,3 +21,4 @@ obj-$(CONFIG_DRIVER_SERIAL_ALTERA) += serial_altera.o obj-$(CONFIG_DRIVER_SERIAL_ALTERA_JTAG) += serial_altera_jtag.o obj-$(CONFIG_DRIVER_SERIAL_PXA) += serial_pxa.o obj-$(CONFIG_DRIVER_SERIAL_OMAP4_USBBOOT) += serial_omap4_usbboot.o +obj-$(CONFIG_DRIVER_SERIAL_ZYNQ) += serial_zynq.odrivers/serial/serial_zynq.c new file +102
-0@@ -0,0 +1,144 @@ +/* +* (C) Copyright 2013 Josh Cartwright +* +* Based very loosely on u-boot drivers/serial/serial_zynq.c. +* +* Copyright (C) 2012 Michal Simek <[email protected]> +* Copyright (C) 2011-2012 Xilinx, Inc. All rights reserved. +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ +#include <common.h> +#include <io.h> +#include <init.h> +#include <driver.h> +#include <xfuncs.h> +#include <console.h> +#include <malloc.h> + +#include <linux/clk.h> + +#define UART_CR 0x00000000 +#define UART_CR_TXEN (1<<4) +#define UART_CR_RXEN (1<<2) +#define UART_CR_TXRST (1<<1) +#define UART_CR_RXRST (1<<0) + +#define UART_SR 0x0000002C +#define UART_SR_TXFULL (1<<4) +#define UART_SR_TXEMPTY (1<<3) +#define UART_SR_RXFULL (1<<2) +#define UART_SR_RXEMPTY (1<<1) + +#define UART_FIFO 0x00000030 + +struct zynq_serial_device { +struct console_device cdev; +struct clk *clk; +void __iomem *regs; +}; + +#define to_zynq_device (p) container_of(p, struct zynq_serial_device, cdev) + +static void zynq_serial_init_device (struct zynq_serial_device *dev) +{ +writel (UART_CR_TXEN |UART_CR_RXEN |UART_CR_TXEN |UART_CR_RXEN , + dev->regs +UART_CR ); +} + +static int zynq_serial_tstc (struct console_device *cdev) +{ +struct zynq_serial_device *zynq =to_zynq_device (cdev); + +return !(readl (zynq->regs +UART_SR ) &UART_SR_RXEMPTY ); +} + +static void zynq_serial_putc (struct console_device *cdev,char c) +{ +struct zynq_serial_device *zynq =to_zynq_device (cdev); + +while (readl (zynq->regs +UART_SR ) &UART_SR_TXFULL ); + +writel (c, zynq->regs +UART_FIFO ); +} + +static int zynq_serial_getc (struct console_device *cdev) +{ +struct zynq_serial_device *zynq =to_zynq_device (cdev); + +return readl (zynq->regs +UART_FIFO ); +} + +static void zynq_serial_flush (struct console_device *cdev) +{ +struct zynq_serial_device *zynq =to_zynq_device (cdev); + +while (!(readl (zynq->regs +UART_SR ) &UART_SR_TXEMPTY )); +} + +static int zynq_serial_probe (struct device_d *dev) +{ +struct zynq_serial_device *priv; +struct console_device *cdev; +int err; + + priv =xzalloc (sizeof (*priv)); + cdev = &priv->cdev;
drivers/serial/serial_zynq.c line 112
Quoted 10 lines
drivers/serial/serial_zynq.c new file +10
-0+ + priv->regs =dev_request_mem_region (dev,0 ); + cdev->dev = dev; + cdev->f_caps =CONSOLE_STDIN |CONSOLE_STDOUT |CONSOLE_STDERR ; + cdev->tstc = zynq_serial_tstc; + cdev->putc = zynq_serial_putc; + cdev->getc = zynq_serial_getc; + cdev->flush = zynq_serial_flush; + + priv->clk =clk_get (dev,NULL );
you need to check here too
Quoted 41 lines
drivers/serial/serial_zynq.c new file +32
-0+ + err =clk_enable (priv->clk); +if (err) { +free (priv); +return err; + } + +zynq_serial_init_device (priv); + + dev->priv = priv; + +return console_register (cdev); +} + +static void zynq_serial_remove (struct device_d *dev) +{ +struct zynq_serial_device *zynq = dev->priv; +clk_disable (zynq->clk); +free (zynq); +} + +static struct driver_d zynq_serial_driver = { + .name ="zynq_serial" , + .probe = zynq_serial_probe, + .remove = zynq_serial_remove, +}; + +static int zynq_serial_init (void ) +{ +return platform_driver_register (&zynq_serial_driver); +} +console_initcall (zynq_serial_init);Signature · 8 lines
1.8.1.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH 3/5] ARM: zynq: add driver for Zynq uarts
In reply to Josh CartwrightQuoted 162 lines · Josh Cartwright
Simple UART driver for Zynq SoCs, based loosely on the u-boot driver.
Signed-off-by Josh Cartwright <[email protected]>--- drivers/serial/Kconfig | 6 ++ drivers/serial/Makefile | 1 + drivers/serial/serial_zynq.c | 144 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 151 insertions(+) create mode 100644 drivers/serial/serial_zynq.cdrivers/serial/Kconfig +6
-0@@ -113,4 +113,10 @@ config DRIVER_SERIAL_OMAP4_USBBOOT help Enable this to get console support over the usb bus used to boot an OMAP4 +config DRIVER_SERIAL_ZYNQ + bool "driver for Zynq uarts" + default n + help + Say Y here to get console out support with the Zynq uarts + endmenudrivers/serial/Makefile +1
-0@@ -21,3 +21,4 @@ obj-$(CONFIG_DRIVER_SERIAL_ALTERA) += serial_altera.o obj-$(CONFIG_DRIVER_SERIAL_ALTERA_JTAG) += serial_altera_jtag.o obj-$(CONFIG_DRIVER_SERIAL_PXA) += serial_pxa.o obj-$(CONFIG_DRIVER_SERIAL_OMAP4_USBBOOT) += serial_omap4_usbboot.o +obj-$(CONFIG_DRIVER_SERIAL_ZYNQ) += serial_zynq.odrivers/serial/serial_zynq.c new file +121
-0@@ -0,0 +1,144 @@ +/* +* (C) Copyright 2013 Josh Cartwright +* +* Based very loosely on u-boot drivers/serial/serial_zynq.c. +* +* Copyright (C) 2012 Michal Simek <[email protected]> +* Copyright (C) 2011-2012 Xilinx, Inc. All rights reserved. +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ +#include <common.h> +#include <io.h> +#include <init.h> +#include <driver.h> +#include <xfuncs.h> +#include <console.h> +#include <malloc.h> + +#include <linux/clk.h> + +#define UART_CR 0x00000000 +#define UART_CR_TXEN (1<<4) +#define UART_CR_RXEN (1<<2) +#define UART_CR_TXRST (1<<1) +#define UART_CR_RXRST (1<<0) + +#define UART_SR 0x0000002C +#define UART_SR_TXFULL (1<<4) +#define UART_SR_TXEMPTY (1<<3) +#define UART_SR_RXFULL (1<<2) +#define UART_SR_RXEMPTY (1<<1) + +#define UART_FIFO 0x00000030 + +struct zynq_serial_device { +struct console_device cdev; +struct clk *clk; +void __iomem *regs; +}; + +#define to_zynq_device (p) container_of(p, struct zynq_serial_device, cdev) + +static void zynq_serial_init_device (struct zynq_serial_device *dev) +{ +writel (UART_CR_TXEN |UART_CR_RXEN |UART_CR_TXEN |UART_CR_RXEN , + dev->regs +UART_CR ); +} + +static int zynq_serial_tstc (struct console_device *cdev) +{ +struct zynq_serial_device *zynq =to_zynq_device (cdev); + +return !(readl (zynq->regs +UART_SR ) &UART_SR_RXEMPTY ); +} + +static void zynq_serial_putc (struct console_device *cdev,char c) +{ +struct zynq_serial_device *zynq =to_zynq_device (cdev); + +while (readl (zynq->regs +UART_SR ) &UART_SR_TXFULL ); + +writel (c, zynq->regs +UART_FIFO ); +} + +static int zynq_serial_getc (struct console_device *cdev) +{ +struct zynq_serial_device *zynq =to_zynq_device (cdev); + +return readl (zynq->regs +UART_FIFO ); +} + +static void zynq_serial_flush (struct console_device *cdev) +{ +struct zynq_serial_device *zynq =to_zynq_device (cdev); + +while (!(readl (zynq->regs +UART_SR ) &UART_SR_TXEMPTY )); +} + +static int zynq_serial_probe (struct device_d *dev) +{ +struct zynq_serial_device *priv; +struct console_device *cdev; +int err; + + priv =xzalloc (sizeof (*priv)); + cdev = &priv->cdev; + + priv->regs =dev_request_mem_region (dev,0 ); + cdev->dev = dev; + cdev->f_caps =CONSOLE_STDIN |CONSOLE_STDOUT |CONSOLE_STDERR ; + cdev->tstc = zynq_serial_tstc; + cdev->putc = zynq_serial_putc; + cdev->getc = zynq_serial_getc; + cdev->flush = zynq_serial_flush; + + priv->clk =clk_get (dev,NULL ); + + err =clk_enable (priv->clk); +if (err) { +free (priv); +return err; + } + +zynq_serial_init_device (priv); +
drivers/serial/serial_zynq.c line 131
Quoted 10 lines
drivers/serial/serial_zynq.c new file +10
-0+ dev->priv = priv; + +return console_register (cdev); +} + +static void zynq_serial_remove (struct device_d *dev) +{ +struct zynq_serial_device *zynq = dev->priv; +clk_disable (zynq->clk); +free (zynq);
do;nt do so otherwise the kernel will have no uart for decompress and earlyprintk
Quoted 22 lines
drivers/serial/serial_zynq.c new file +13
-0+} + +static struct driver_d zynq_serial_driver = { + .name ="zynq_serial" , + .probe = zynq_serial_probe, + .remove = zynq_serial_remove, +}; + +static int zynq_serial_init (void ) +{ +return platform_driver_register (&zynq_serial_driver); +} +console_initcall (zynq_serial_init);Signature · 8 lines
1.8.1.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
PATCH 4/5 ARM: zynq: add support for Zynq 7000 SoC
In reply to Josh Cartwright--- arch/arm/Kconfig | 9 + arch/arm/mach-zynq/Kconfig | 3 + arch/arm/mach-zynq/Makefile | 1 + arch/arm/mach-zynq/clocks.c | 341 +++++++++++++++++++++++++++++ arch/arm/mach-zynq/include/mach/clkdev.h | 7 + arch/arm/mach-zynq/include/mach/debug_ll.h | 21 ++ arch/arm/mach-zynq/include/mach/slcr.h | 26 +++ arch/arm/mach-zynq/reset.c | 28 +++ 8 files changed, 436 insertions(+) create mode 100644 arch/arm/mach-zynq/Kconfig create mode 100644 arch/arm/mach-zynq/Makefile create mode 100644 arch/arm/mach-zynq/clocks.c create mode 100644 arch/arm/mach-zynq/include/mach/clkdev.h create mode 100644 arch/arm/mach-zynq/include/mach/debug_ll.h create mode 100644 arch/arm/mach-zynq/include/mach/slcr.h create mode 100644 arch/arm/mach-zynq/reset.c
arch/arm/Kconfig +9 -0
@@ -110,6 +110,14 @@ config ARCH_TEGRA select CPU_ARM926T select HAS_DEBUG_LL +config ARCH_ZYNQ + bool "Xilinx Zynq-based boards" + select CPU_V7 + select HAS_DEBUG_LL + select CLKDEV_LOOKUP + select COMMON_CLK + select ARM_SMP_TWD + endchoice source arch/arm/cpu/Kconfig
@@ -126,6 +134,7 @@ source arch/arm/mach-pxa/Kconfig source arch/arm/mach-samsung/Kconfig source arch/arm/mach-versatile/Kconfig source arch/arm/mach-tegra/Kconfig +source arch/arm/mach-zynq/Kconfig config ARM_ASM_UNIFIED bool
arch/arm/mach-zynq/Kconfig new file +3 -0
@@ -0,0 +1,3 @@ +if ARCH_ZYNQ + +endif
arch/arm/mach-zynq/Makefile new file +1 -0
@@ -0,0 +1 @@ +obj-y += reset.o clocks.o
arch/arm/mach-zynq/clocks.c new file +341 -0
341 lines not on this page · raw message
arch/arm/mach-zynq/include/mach/clkdev.h new file +7 -0
@@ -0,0 +1,7 @@ +#ifndef __ASM_MACH_CLKDEV_H +#define __ASM_MACH_CLKDEV_H + +#define __clk_get (clk) ({ 1; }) +#define __clk_put (clk) do { } while (0) + +#endif
arch/arm/mach-zynq/include/mach/debug_ll.h new file +21 -0
@@ -0,0 +1,21 @@ +#ifndef __MACH_DEBUG_LL_H__ +#define __MACH_DEBUG_LL_H__ + +#include <io.h> + +#define UART_BASE 0xE0001000 +#define UART_SR 0x0000002C +#define UART_FIFO 0x00000030 + +#define UART_SR_TXEMPTY (1<<3) + +static inline void PUTC_LL (char c) +{ +void __iomem *base = (void __iomem *)UART_BASE ; + +writel (c, base +UART_FIFO ); + +while (!(readl (base +UART_SR ) &UART_SR_TXEMPTY )); +} + +#endif
arch/arm/mach-zynq/include/mach/slcr.h new file +26 -0
@@ -0,0 +1,26 @@ +#ifndef __MACH_SLCR_H__ +#define __MACH_SLCR_H__ + +#include <io.h> + +#define SLCR_BASE 0xF8000000 +#define SLCR_LOCK 0x00000004 +#define SLCR_UNLOCK 0x00000008 +#define SLCR_PSS_RST_CTRL 0x00000200 + +static inline void slcr_write (unsigned long val,unsigned long reg) +{ +writel (val,SLCR_BASE + reg); +} + +static inline void slcr_unlock (void ) +{ +slcr_write (0xDF0D ,SLCR_UNLOCK ); +} + +static inline void slcr_lock (void ) +{ +slcr_write (0x767B ,SLCR_LOCK ); +} + +#endif
arch/arm/mach-zynq/reset.c new file +28 -0
@@ -0,0 +1,28 @@ +/* +* Copyright (C) 2013 Josh Cartwright <[email protected]> +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ +#include <common.h> +#include <mach/slcr.h> + +void __noreturn reset_cpu (unsigned long addr) +{ +slcr_unlock (); +slcr_write (1 ,SLCR_PSS_RST_CTRL ); + +while (1 ); +}
Signature · 8 lines
1.8.1.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH 4/5] ARM: zynq: add support for Zynq 7000 SoC
Quoted 494 lines · Josh Cartwright
Signed-off-by Josh Cartwright <[email protected]>--- arch/arm/Kconfig | 9 + arch/arm/mach-zynq/Kconfig | 3 + arch/arm/mach-zynq/Makefile | 1 + arch/arm/mach-zynq/clocks.c | 341 +++++++++++++++++++++++++++++ arch/arm/mach-zynq/include/mach/clkdev.h | 7 + arch/arm/mach-zynq/include/mach/debug_ll.h | 21 ++ arch/arm/mach-zynq/include/mach/slcr.h | 26 +++ arch/arm/mach-zynq/reset.c | 28 +++ 8 files changed, 436 insertions(+) create mode 100644 arch/arm/mach-zynq/Kconfig create mode 100644 arch/arm/mach-zynq/Makefile create mode 100644 arch/arm/mach-zynq/clocks.c create mode 100644 arch/arm/mach-zynq/include/mach/clkdev.h create mode 100644 arch/arm/mach-zynq/include/mach/debug_ll.h create mode 100644 arch/arm/mach-zynq/include/mach/slcr.h create mode 100644 arch/arm/mach-zynq/reset.carch/arm/Kconfig +9
-0@@ -110,6 +110,14 @@ config ARCH_TEGRA select CPU_ARM926T select HAS_DEBUG_LL +config ARCH_ZYNQ + bool "Xilinx Zynq-based boards" + select CPU_V7 + select HAS_DEBUG_LL + select CLKDEV_LOOKUP + select COMMON_CLK + select ARM_SMP_TWD + endchoice source arch/arm/cpu/Kconfig@@ -126,6 +134,7 @@ source arch/arm/mach-pxa/Kconfig source arch/arm/mach-samsung/Kconfig source arch/arm/mach-versatile/Kconfig source arch/arm/mach-tegra/Kconfig +source arch/arm/mach-zynq/Kconfig config ARM_ASM_UNIFIED boolarch/arm/mach-zynq/Kconfig new file +3
-0@@ -0,0 +1,3 @@ +if ARCH_ZYNQ + +endifarch/arm/mach-zynq/Makefile new file +1
-0@@ -0,0 +1 @@ +obj-y += reset.o clocks.oarch/arm/mach-zynq/clocks.c new file +341
-0@@ -0,0 +1,341 @@ +/* +* Copyright (c) 2013 Josh Cartwright <[email protected]> +* +* Based on drivers/clk-zynq.c from Linux. +* +* Copyright (c) 2012 National Instruments +* +* Josh Cartwright <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms and conditions of the GNU General Public License, +* version 2, as published by the Free Software Foundation. +* +* This program is distributed in the hope it will be useful, but WITHOUT +* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or +* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for +* more details. +* +* You should have received a copy of the GNU General Public License along with +* this program. If not, see <http://www.gnu.org/licenses/>. +*/ +#include <common.h> +#include <init.h> +#include <malloc.h> +#include <linux/clk.h> +#include <linux/clkdev.h> +#include <linux/err.h> + +#include <io.h> + +#define ZYNQ_SLCR_BASE 0xF8000000 + +enum zynq_clks { + dummy, ps_clk, arm_pll, ddr_pll, io_pll, uart_clk, uart0, uart1, + cpu_clk, cpu_6x4x, cpu_3x2x, cpu_2x, cpu_1x, clks_max +}; + +static struct clk *clks[clks_max]; + +struct zynq_pll_clk { +struct clk clk; +void __iomem *pll_ctrl; +}; + +#define to_zynq_pll_clk (c) container_of(c, struct zynq_pll_clk, clk) + +#define PLL_CTRL_FDIV (x) (((x) >> 12) & 0x7F) + +static unsigned long zynq_pll_recalc_rate (struct clk *clk, +unsigned long parent_rate) +{ +struct zynq_pll_clk *pll =to_zynq_pll_clk (clk); +return parent_rate *PLL_CTRL_FDIV (readl (pll->pll_ctrl)); +} + +static struct clk_ops zynq_pll_clk_ops = { + .recalc_rate = zynq_pll_recalc_rate, +}; + +static inline struct clk *zynq_pll_clk (const char *name,void __iomem *pll_ctrl) +{ +static const char *pll_parent ="ps_clk" ; +struct zynq_pll_clk *pll; +int ret; + + pll =xzalloc (sizeof (*pll)); + + pll->pll_ctrl = pll_ctrl; + pll->clk.ops = &zynq_pll_clk_ops; + pll->clk.name = name; + pll->clk.parent_names = &pll_parent; + pll->clk.num_parents =1 ; + + ret =clk_register (&pll->clk); +if (ret) { +free (pll); +return ERR_PTR (ret); + } + +return &pll->clk; +} + +struct zynq_periph_clk { +struct clk clk; +void __iomem *clk_ctrl; +}; + +#define to_zynq_periph_clk (c) container_of(c, struct zynq_periph_clk, c) + +static const u8 periph_clk_parent_map[] = { +0 ,0 ,1 ,2 +}; +#define PERIPH_CLK_CTRL_SRC (x) (periph_clk_parent_map[((x) & 0x30) >> 4]) +#define PERIPH_CLK_CTRL_DIV (x) (((x) & 0x3F00) >> 8) + +static unsigned long zynq_periph_recalc_rate (struct clk *clk, +unsigned long parent_rate) +{ +struct zynq_periph_clk *periph =to_zynq_periph_clk (clk); +return parent_rate /PERIPH_CLK_CTRL_DIV (readl (periph->clk_ctrl)); +} + +static int zynq_periph_get_parent (struct clk *clk) +{ +struct zynq_periph_clk *periph =to_zynq_periph_clk (clk); +return PERIPH_CLK_CTRL_SRC (readl (periph->clk_ctrl)); +} + +static const struct clk_ops zynq_periph_clk_ops = { + .recalc_rate = zynq_periph_recalc_rate, + .get_parent = zynq_periph_get_parent, +}; + +static struct clk *zynq_periph_clk (const char *name,void __iomem *clk_ctrl) +{ +static const char *peripheral_parents[] = { +"io_pll" , +"arm_pll" , +"ddr_pll" , + }; +struct zynq_periph_clk *periph; +int ret; + + periph =xzalloc (sizeof (*periph)); + + periph->clk_ctrl = clk_ctrl; + periph->clk.name = name; + periph->clk.ops = &zynq_periph_clk_ops; + + periph->clk.parent_names = peripheral_parents; + periph->clk.num_parents =ARRAY_SIZE (peripheral_parents); + + ret =clk_register (&periph->clk); +if (ret) { +free (periph); +return ERR_PTR (ret); + } + +return &periph->clk; +} + +/* CPU Clock domain is modelled as a mux with 4 children subclks, whose +* derivative rates depend on CLK_621_TRUE +*/ + +struct zynq_cpu_clk { +struct clk clk; +void __iomem *clk_ctrl; +}; + +#define to_zynq_cpu_clk (c) container_of(c, struct zynq_cpu_clk, c) + +static const u8 zynq_cpu_clk_parent_map[] = { +1 ,1 ,2 ,0 +}; +#define CPU_CLK_SRCSEL (x) (zynq_cpu_clk_parent_map[(((x) & 0x30) >> 4)]) +#define CPU_CLK_CTRL_DIV (x) (((x) & 0x3F00) >> 8) + +static unsigned long zynq_cpu_clk_recalc_rate (struct clk *clk, +unsigned long parent_rate) +{ +struct zynq_cpu_clk *cpuclk =to_zynq_cpu_clk (clk); +return parent_rate /CPU_CLK_CTRL_DIV (readl (cpuclk->clk_ctrl)); +} + +static int zynq_cpu_clk_get_parent (struct clk *clk) +{ +struct zynq_cpu_clk *cpuclk =to_zynq_cpu_clk (clk); +return CPU_CLK_SRCSEL (readl (cpuclk->clk_ctrl)); +} + +static const struct clk_ops zynq_cpu_clk_ops = { + .get_parent = zynq_cpu_clk_get_parent, + .recalc_rate = zynq_cpu_clk_recalc_rate, +}; + +static struct clk *zynq_cpu_clk (const char *name,void __iomem *clk_ctrl) +{ +static const char *cpu_parents[] = { +"io_pll" , +"arm_pll" , +"ddr_pll" , + }; +struct zynq_cpu_clk *cpu; +int ret; + + cpu =xzalloc (sizeof (*cpu)); + + cpu->clk_ctrl = clk_ctrl; + cpu->clk.ops = &zynq_cpu_clk_ops; + cpu->clk.name = name; + cpu->clk.parent_names = cpu_parents; + cpu->clk.num_parents =ARRAY_SIZE (cpu_parents); + + ret =clk_register (&cpu->clk); +if (ret) { +free (cpu); +return ERR_PTR (ret); + } + +return &cpu->clk; +} + +enum zynq_cpu_subclk_which { +CPU_SUBCLK_6X4X , +CPU_SUBCLK_3X2X , +CPU_SUBCLK_2X , +CPU_SUBCLK_1X , +}; + +struct zynq_cpu_subclk { +struct clk clk; +void __iomem *clk_ctrl; +void __iomem *clk_621; +enum zynq_cpu_subclk_which which; +}; + +#define CLK_621_TRUE (x) ((x) & 1) + +#define to_zynq_cpu_subclk (c) container_of(c, struct zynq_cpu_subclk, c); + +static unsigned long zynq_cpu_subclk_recalc_rate (struct clk *clk, +unsigned long parent_rate) +{ +unsigned long uninitialized_var (rate ); +struct zynq_cpu_subclk *subclk; +bool is_621; + + subclk =to_zynq_cpu_subclk (clk) + is_621 = CLK_621_TRUE(readl(subclk->clk_621)); + +switch (subclk->which) { +case CPU_SUBCLK_6X4X : + rate = parent_rate; +break ; +case CPU_SUBCLK_3X2X : + rate = parent_rate /2 ; +break ; +case CPU_SUBCLK_2X : + rate = parent_rate / (is_621 ?3 :2 ); +break ; +case CPU_SUBCLK_1X : + rate = parent_rate / (is_621 ?6 :4 ); +break ; + }; + +return rate; +} + +static int zynq_cpu_subclk_enable (struct clk *clk) +{ +struct zynq_cpu_subclk *subclk; +u32 tmp; + + subclk =to_zynq_cpu_subclk (clk); + + tmp =readl (subclk->clk_ctrl); + tmp |=1 << (24 + subclk->which); +writel (tmp, subclk->clk_ctrl); + +return 0 ; +} + +static void zynq_cpu_subclk_disable (struct clk *clk) +{ +struct zynq_cpu_subclk *subclk; +u32 tmp; + + subclk =to_zynq_cpu_subclk (clk); + + tmp =readl (subclk->clk_ctrl); + tmp &= ~(1 << (24 + subclk->which)); +writel (tmp, subclk->clk_ctrl); +} + +static const struct clk_ops zynq_cpu_subclk_ops = { + .enable = zynq_cpu_subclk_enable, + .disable = zynq_cpu_subclk_disable, + .recalc_rate = zynq_cpu_subclk_recalc_rate, +}; + +static struct clk *zynq_cpu_subclk (const char *name, +enum zynq_cpu_subclk_which which, +void __iomem *clk_ctrl, +void __iomem *clk_621) +{ +static const char *subclk_parent ="cpu_clk" ; +struct zynq_cpu_subclk *subclk; +int ret; + + subclk =xzalloc (sizeof (*subclk)); + + subclk->clk_ctrl = clk_ctrl; + subclk->clk_621 = clk_621; + subclk->which = which; + subclk->clk.name = name; + subclk->clk.ops = &zynq_cpu_subclk_ops; + + subclk->clk.parent_names = &subclk_parent; + subclk->clk.num_parents =1 ; + + ret =clk_register (&subclk->clk); +if (ret) { +free (subclk); +return ERR_PTR (ret); + } + +return &subclk->clk; +} + +static int zynq_init_clks (void ) +{ +void __iomem *slcr_base = (void __iomem *)ZYNQ_SLCR_BASE ; + +request_iomem_region ("zynq_slcr" ,ZYNQ_SLCR_BASE , +ZYNQ_SLCR_BASE +0x1000 ); + + clks[ps_clk] =clk_fixed ("ps_clk" ,CONFIG_ZYNQ_PS_CLK_FREQ ); + + clks[arm_pll] =zynq_pll_clk ("arm_pll" , slcr_base +0x100 ); + clks[ddr_pll] =zynq_pll_clk ("ddr_pll" , slcr_base +0x104 ); + clks[ io_pll] =zynq_pll_clk ("io_pll" , slcr_base +0x108 ); + + clks[uart_clk] =zynq_periph_clk ("uart_clk" , slcr_base +0x154 ); + + clks[uart0] =clk_gate ("uart0" ,"uart_clk" , slcr_base +0x154 ,0 ); + clks[uart1] =clk_gate ("uart1" ,"uart_clk" , slcr_base +0x154 ,1 ); + + clks[cpu_clk] =zynq_cpu_clk ("cpu_clk" , slcr_base +0x120 ); + + clks[cpu_6x4x] =zynq_cpu_subclk ("cpu_6x4x" ,CPU_SUBCLK_6X4X , slcr_base +0x120 , slcr_base +0x1C4 ); + clks[cpu_3x2x] =zynq_cpu_subclk ("cpu_3x2x" ,CPU_SUBCLK_3X2X , slcr_base +0x120 , slcr_base +0x1C4 ); + clks[ cpu_2x] =zynq_cpu_subclk ("cpu_2x" ,CPU_SUBCLK_2X , slcr_base +0x120 , slcr_base +0x1C4 ); + clks[ cpu_1x] =zynq_cpu_subclk ("cpu_1x" ,CPU_SUBCLK_1X , slcr_base +0x120 , slcr_base +0x1C4 ); + +clk_register_clkdev (clks[cpu_3x2x],NULL ,"smp_twd0" ); +clk_register_clkdev (clks[uart0],NULL ,"zynq_serial0" ); +clk_register_clkdev (clks[uart1],NULL ,"zynq_serial1" ); +return 0 ; +} +core_initcall (zynq_init_clks);arch/arm/mach-zynq/include/mach/clkdev.h new file +7
-0@@ -0,0 +1,7 @@ +#ifndef __ASM_MACH_CLKDEV_H +#define __ASM_MACH_CLKDEV_H + +#define __clk_get (clk) ({ 1; }) +#define __clk_put (clk) do { } while (0) + +#endif arch/arm/mach-zynq/include/mach/debug_ll.h new file +21
-0@@ -0,0 +1,21 @@ +#ifndef __MACH_DEBUG_LL_H__ +#define __MACH_DEBUG_LL_H__ + +#include <io.h> + +#define UART_BASE 0xE0001000 +#define UART_SR 0x0000002C +#define UART_FIFO 0x00000030 + +#define UART_SR_TXEMPTY (1<<3) + +static inline void PUTC_LL (char c) +{ +void __iomem *base = (void __iomem *)UART_BASE ; + +writel (c, base +UART_FIFO ); + +while (!(readl (base +UART_SR ) &UART_SR_TXEMPTY )); +} + +#endif arch/arm/mach-zynq/include/mach/slcr.h new file +26
-0@@ -0,0 +1,26 @@ +#ifndef __MACH_SLCR_H__ +#define __MACH_SLCR_H__ + +#include <io.h> + +#define SLCR_BASE 0xF8000000 +#define SLCR_LOCK 0x00000004 +#define SLCR_UNLOCK 0x00000008 +#define SLCR_PSS_RST_CTRL 0x00000200 + +static inline void slcr_write (unsigned long val,unsigned long reg) +{ +writel (val,SLCR_BASE + reg); +} + +static inline void slcr_unlock (void ) +{ +slcr_write (0xDF0D ,SLCR_UNLOCK ); +} + +static inline void slcr_lock (void ) +{ +slcr_write (0x767B ,SLCR_LOCK ); +} + +#endif arch/arm/mach-zynq/reset.c new file +7
-0@@ -0,0 +1,28 @@ +/* +* Copyright (C) 2013 Josh Cartwright <[email protected]> +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version.
arch/arm/mach-zynq/reset.c line 17
Quoted 10 lines
arch/arm/mach-zynq/reset.c new file +10
-0+* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA
Please drop the address of the FSF.
See this
commit 77322aa896895f4f68501a071086e432e575dcc2
Author: Sascha Hauer <[email protected]> Date: Tue Jul 31 09:51:20 2012 +0200
Treewide: remove address of the Free Software Foundation
The FSF address has changed in the past. Instead of updating it each time the address changes, just drop it completely treewide.
Quoted 20 lines
arch/arm/mach-zynq/reset.c new file +11
-1+*/ +#include <common.h> +#include <mach/slcr.h> + +void __noreturn reset_cpu (unsigned long addr) +{ +slcr_unlock (); +slcr_write (1 ,SLCR_PSS_RST_CTRL ); + +while (1 ); +} --1.8.1.2
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Signature · 7 lines
Best regards, Antony Pavlov _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH 4/5] ARM: zynq: add support for Zynq 7000 SoC
Quoted 2 lines · Antony Pavlov
Quoted 1 line · Josh Cartwright
Signed-off-by Josh Cartwright <[email protected]>
[..]
Quoted 14 lines
Quoted 14 lines
arch/arm/mach-zynq/reset.c new file +11
-0@@ -0,0 +1,28 @@ +/* +* Copyright (C) 2013 Josh Cartwright <[email protected]> +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
Quoted 8 lines
arch/arm/mach-zynq/reset.c line 17
Quoted 6 lines
arch/arm/mach-zynq/reset.c new file +6
-0+* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA Please drop the address of the FSF.
Okay, will-do. It's also included in the notice in the serial driver, but I'm a little weary about it's removal there since it's taken verbatim from the copyright notice in the u-boot driver.
Josh
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH 4/5] ARM: zynq: add support for Zynq 7000 SoC
Quoted 27 lines · Josh Cartwright
Quoted 2 lines · Antony Pavlov
Quoted 1 line · Josh Cartwright
Signed-off-by Josh Cartwright <[email protected]>[..]
Quoted 14 lines
Quoted 14 lines
arch/arm/mach-zynq/reset.c new file +11
-0@@ -0,0 +1,28 @@ +/* +* Copyright (C) 2013 Josh Cartwright <[email protected]> +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the Quoted 8 lines
arch/arm/mach-zynq/reset.c line 17
Quoted 6 lines
arch/arm/mach-zynq/reset.c new file +6
-0+* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA Please drop the address of the FSF.
Quoted 3 lines
Okay, will-do. It's also included in the notice in the serial driver, but I'm a little weary about it's removal there since it's taken verbatim from the copyright notice in the u-boot driver.
It's fine to remove it. The address is wrong anyway. You should leave a note though where the code comes from, either in the commit log or in the header.
Sascha
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH 5/5 ARM: zynq: add support for zc702 development board
In reply to Josh Cartwright--- arch/arm/Makefile | 2 + arch/arm/boards/zynq-zc702/Makefile | 1 + arch/arm/boards/zynq-zc702/config.h | 0 arch/arm/boards/zynq-zc702/devices.c | 70 +++++++++++++++++++++++++++++++++++ arch/arm/boards/zynq-zc702/lowlevel.c | 28 ++++++++++++++ arch/arm/mach-zynq/Kconfig | 19 ++++++++++ 6 files changed, 120 insertions(+) create mode 100644 arch/arm/boards/zynq-zc702/Makefile create mode 100644 arch/arm/boards/zynq-zc702/config.h create mode 100644 arch/arm/boards/zynq-zc702/devices.c create mode 100644 arch/arm/boards/zynq-zc702/lowlevel.c
arch/arm/Makefile +2 -0
@@ -64,6 +64,7 @@ machine-$(CONFIG_ARCH_PXA) := pxa machine-$(CONFIG_ARCH_SAMSUNG) := samsung machine-$(CONFIG_ARCH_VERSATILE) := versatile machine-$(CONFIG_ARCH_TEGRA) := tegra +machine-$(CONFIG_ARCH_ZYNQ) := zynq # Board directory name. This list is sorted alphanumerically # by CONFIG_* macro name.
@@ -157,6 +158,7 @@ board-$(CONFIG_MACH_SABRELITE) := freescale-mx6-sabrelite board-$(CONFIG_MACH_TX53) := karo-tx53 board-$(CONFIG_MACH_GUF_VINCELL) := guf-vincell board-$(CONFIG_MACH_EFIKA_MX_SMARTBOOK) := efika-mx-smartbook +board-$(CONFIG_MACH_ZYNQ_ZC702) := zynq-zc702 machdirs := $(patsubst %,arch/arm/mach-%/,$(machine-y))
arch/arm/boards/zynq-zc702/Makefile new file +1 -0
@@ -0,0 +1 @@ +obj-y += lowlevel.o devices.o
arch/arm/boards/zynq-zc702/config.h new file +0 -0
arch/arm/boards/zynq-zc702/devices.c new file +70 -0
70 lines not on this page · raw message
arch/arm/boards/zynq-zc702/lowlevel.c new file +28 -0
@@ -0,0 +1,28 @@ +/* +* Copyright (c) 2013 Josh Cartwright <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms and conditions of the GNU General Public License, +* version 2, as published by the Free Software Foundation. +* +* This program is distributed in the hope it will be useful, but WITHOUT +* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or +* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for +* more details. +* +* You should have received a copy of the GNU General Public License along with +* this program. If not, see <http://www.gnu.org/licenses/>. +*/ +#include <common.h> +#include <init.h> +#include <asm/barebox-arm.h> +#include <asm/barebox-arm-head.h> + +#include <mach/slcr.h> + +void __naked __bare_init barebox_arm_reset_vector(void) +{ +slcr_unlock (); +arm_cpu_lowlevel_init (); +barebox_arm_entry (0x8000 ,SZ_128M ,0 ); +}
arch/arm/mach-zynq/Kconfig +19 -0
@@ -1,3 +1,22 @@ if ARCH_ZYNQ +config ARCH_TEXT_BASE + hex + default 0x04000000 if MACH_ZYNQ_ZC702 + +config ZYNQ_PS_CLK_FREQ + int + default 33333330 if MACH_ZYNQ_ZC702 + +config BOARDINFO + default "Xilinx Zynq zc702 dev board" if MACH_ZYNQ_ZC702 + +choice + prompt "Xilinx Zynq zc702 dev board" + +config MACH_ZYNQ_ZC702 + bool "zc702 development board" + +endchoice + endif
Signature · 7 lines
1.8.1.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH 5/5] ARM: zynq: add support for zc702 development board
Quoted 90 lines · Josh Cartwright
Signed-off-by Josh Cartwright <[email protected]>--- arch/arm/Makefile | 2 + arch/arm/boards/zynq-zc702/Makefile | 1 + arch/arm/boards/zynq-zc702/config.h | 0 arch/arm/boards/zynq-zc702/devices.c | 70 +++++++++++++++++++++++++++++++++++ arch/arm/boards/zynq-zc702/lowlevel.c | 28 ++++++++++++++ arch/arm/mach-zynq/Kconfig | 19 ++++++++++ 6 files changed, 120 insertions(+) create mode 100644 arch/arm/boards/zynq-zc702/Makefile create mode 100644 arch/arm/boards/zynq-zc702/config.h create mode 100644 arch/arm/boards/zynq-zc702/devices.c create mode 100644 arch/arm/boards/zynq-zc702/lowlevel.carch/arm/Makefile +2
-0@@ -64,6 +64,7 @@ machine-$(CONFIG_ARCH_PXA) := pxa machine-$(CONFIG_ARCH_SAMSUNG) := samsung machine-$(CONFIG_ARCH_VERSATILE) := versatile machine-$(CONFIG_ARCH_TEGRA) := tegra +machine-$(CONFIG_ARCH_ZYNQ) := zynq # Board directory name. This list is sorted alphanumerically # by CONFIG_* macro name.@@ -157,6 +158,7 @@ board-$(CONFIG_MACH_SABRELITE) := freescale-mx6-sabrelite board-$(CONFIG_MACH_TX53) := karo-tx53 board-$(CONFIG_MACH_GUF_VINCELL) := guf-vincell board-$(CONFIG_MACH_EFIKA_MX_SMARTBOOK) := efika-mx-smartbook +board-$(CONFIG_MACH_ZYNQ_ZC702) := zynq-zc702 machdirs := $(patsubst %,arch/arm/mach-%/,$(machine-y))arch/arm/boards/zynq-zc702/Makefile new file +1
-0@@ -0,0 +1 @@ +obj-y += lowlevel.o devices.oarch/arm/boards/zynq-zc702/config.h new file +0
-0arch/arm/boards/zynq-zc702/devices.c new file +39
-0@@ -0,0 +1,70 @@ +/* +* Copyright (c) 2013 Josh Cartwright <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms and conditions of the GNU General Public License, +* version 2, as published by the Free Software Foundation. +* +* This program is distributed in the hope it will be useful, but WITHOUT +* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or +* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for +* more details. +* +* You should have received a copy of the GNU General Public License along with +* this program. If not, see <http://www.gnu.org/licenses/>. +*/ +#include <common.h> +#include <driver.h> +#include <init.h> +#include <sizes.h> + +#include <asm/memory.h> + +static struct resource smp_twd_resource = { + .name ="smp_twd_base" , + .start =0xF8F00600 , + .end =0xF8F00610 , + .flags =IORESOURCE_MEM , +}; + +static struct device_d zynq_smp_twd = { + .id =DEVICE_ID_DYNAMIC , + .name ="smp_twd" , + .num_resources =1 , + .resource = &smp_twd_resource, +}; + +static struct resource zynq_serial_resource = { + .name ="zynq_serial_base" , + .start =0xE0001000 ,
arch/arm/boards/zynq-zc702/devices.c line 49
Quoted 10 lines
arch/arm/boards/zynq-zc702/devices.c new file +10
-0+ .end = 0xE0001048, + .flags = IORESOURCE_MEM, +}; + +static struct device_d zynq_serial = { + .id =DEVICE_ID_DYNAMIC , + .name ="zynq_serial" , + .num_resources =1 , + .resource = &zynq_serial_resource, +};
use generic code to register the devices
Quoted 44 lines
arch/arm/boards/zynq-zc702/devices.c new file +21
-0+ +static int zc702_console_init (void ) +{ +platform_device_register (&zynq_serial); +return 0 ; +} +console_initcall (zc702_console_init); + +static int zc702_mem_init (void ) +{ +arm_add_mem_device ("ram0" ,0 ,SZ_128M ); +return 0 ; +} +mem_initcall (zc702_mem_init); + +static int zc702_twd_init (void ) +{ +platform_device_register (&zynq_smp_twd); +return 0 ; +} +coredevice_initcall (zc702_twd_init);arch/arm/boards/zynq-zc702/lowlevel.c new file +17
-0@@ -0,0 +1,28 @@ +/* +* Copyright (c) 2013 Josh Cartwright <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms and conditions of the GNU General Public License, +* version 2, as published by the Free Software Foundation. +* +* This program is distributed in the hope it will be useful, but WITHOUT +* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or +* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for +* more details. +* +* You should have received a copy of the GNU General Public License along with +* this program. If not, see <http://www.gnu.org/licenses/>. +*/ +#include <common.h> +#include <init.h>
arch/arm/boards/zynq-zc702/lowlevel.c line 27
Quoted 10 lines
arch/arm/boards/zynq-zc702/lowlevel.c new file +10
-0+#include <asm/barebox-arm.h> +#include <asm/barebox-arm-head.h> + +#include <mach/slcr.h> + +void __naked __bare_init barebox_arm_reset_vector(void) +{ +slcr_unlock (); +arm_cpu_lowlevel_init (); +barebox_arm_entry (0x8000 ,SZ_128M ,0 );
can you detect the ddr size
Quoted 6 lines
arch/arm/boards/zynq-zc702/lowlevel.c new file +1
-0+}arch/arm/mach-zynq/Kconfig +0
-0
arch/arm/mach-zynq/Kconfig line 9
Quoted 9 lines
arch/arm/mach-zynq/Kconfig +7
-0@@ -1,3 +1,22 @@ if ARCH_ZYNQ +config ARCH_TEXT_BASE + hex + default 0x04000000 if MACH_ZYNQ_ZC702 + +config ZYNQ_PS_CLK_FREQ + int + default 33333330 if MACH_ZYNQ_ZC702
move it to C
Quoted 18 lines
arch/arm/mach-zynq/Kconfig +12
-0+ +config BOARDINFO + default "Xilinx Zynq zc702 dev board" if MACH_ZYNQ_ZC702 + +choice + prompt "Xilinx Zynq zc702 dev board" + +config MACH_ZYNQ_ZC702 + bool "zc702 development board" + +endchoice + endifSignature · 4 lines
1.8.1.2 _______________________________________________
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH 5/5] ARM: zynq: add support for zc702 development board
Thanks for the review!
Quoted 1 line · Jean-Christophe PLAGNIOL-VILLARD
On 18:48 Sat 02 Mar , Josh Cartwright wrote:
[..]
Quoted 47 lines
Quoted 47 lines
index 0000000..b9ec9f3
arch/arm/boards/zynq-zc702/devices.c new file +43
-0@@ -0,0 +1,70 @@ +/* +* Copyright (c) 2013 Josh Cartwright <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms and conditions of the GNU General Public License, +* version 2, as published by the Free Software Foundation. +* +* This program is distributed in the hope it will be useful, but WITHOUT +* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or +* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for +* more details. +* +* You should have received a copy of the GNU General Public License along with +* this program. If not, see <http://www.gnu.org/licenses/>. +*/ +#include <common.h> +#include <driver.h> +#include <init.h> +#include <sizes.h> + +#include <asm/memory.h> + +static struct resource smp_twd_resource = { + .name ="smp_twd_base" , + .start =0xF8F00600 , + .end =0xF8F00610 , + .flags =IORESOURCE_MEM , +}; + +static struct device_d zynq_smp_twd = { + .id =DEVICE_ID_DYNAMIC , + .name ="smp_twd" , + .num_resources =1 , + .resource = &smp_twd_resource, +}; + +static struct resource zynq_serial_resource = { + .name ="zynq_serial_base" , + .start =0xE0001000 , + .end =0xE0001048 , + .flags =IORESOURCE_MEM , +}; +
Quoted 8 lines
arch/arm/boards/zynq-zc702/devices.c line 49
Quoted 6 lines
arch/arm/boards/zynq-zc702/devices.c new file +6
-0+static struct device_d zynq_serial = { + .id =DEVICE_ID_DYNAMIC , + .name ="zynq_serial" , + .num_resources =1 , + .resource = &zynq_serial_resource, +};use generic code to register the devices
I'm assuming you're referring to add_generic_device() and friends. I'll look into it.
[..]
Quoted 22 lines
Quoted 22 lines
arch/arm/boards/zynq-zc702/devices.c new file +21
-0+++ b/arch/arm/boards/zynq-zc702/lowlevel.c@@ -0,0 +1,28 @@ +/* +* Copyright (c) 2013 Josh Cartwright <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms and conditions of the GNU General Public License, +* version 2, as published by the Free Software Foundation. +* +* This program is distributed in the hope it will be useful, but WITHOUT +* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or +* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for +* more details. +* +* You should have received a copy of the GNU General Public License along with +* this program. If not, see <http://www.gnu.org/licenses/>. +*/ +#include <common.h> +#include <init.h> +#include <asm/barebox-arm.h> +#include <asm/barebox-arm-head.h> +
Quoted 8 lines
arch/arm/boards/zynq-zc702/devices.c line 27
Quoted 7 lines
arch/arm/boards/zynq-zc702/devices.c new file +7
-0+#include <mach/slcr.h> + +void __naked __bare_init barebox_arm_reset_vector(void) +{ +slcr_unlock (); +arm_cpu_lowlevel_init (); +barebox_arm_entry (0x8000 ,SZ_128M ,0 );can you detect the ddr size
I don't think this is possible, but I'll look a bit more.
Quoted 8 lines
Quoted 8 lines
arch/arm/boards/zynq-zc702/devices.c new file +1
-0+}arch/arm/mach-zynq/Kconfig +0
-0@@ -1,3 +1,22 @@ if ARCH_ZYNQ
Quoted 8 lines
arch/arm/mach-zynq/Kconfig line 9
Quoted 7 lines
arch/arm/mach-zynq/Kconfig +7
-0+config ARCH_TEXT_BASE + hex + default 0x04000000 if MACH_ZYNQ_ZC702 + +config ZYNQ_PS_CLK_FREQ + int + default 33333330 if MACH_ZYNQ_ZC702move it to C
Will-do.
Thanks again,
Josh
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH 5/5] ARM: zynq: add support for zc702 development board
Quoted 61 lines · Josh Cartwright
Thanks for the review!
Quoted 1 line · Jean-Christophe PLAGNIOL-VILLARD
On 18:48 Sat 02 Mar , Josh Cartwright wrote:
[..]
Quoted 47 lines
Quoted 47 lines
index 0000000..b9ec9f3
arch/arm/boards/zynq-zc702/devices.c new file +43
-0@@ -0,0 +1,70 @@ +/* +* Copyright (c) 2013 Josh Cartwright <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms and conditions of the GNU General Public License, +* version 2, as published by the Free Software Foundation. +* +* This program is distributed in the hope it will be useful, but WITHOUT +* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or +* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for +* more details. +* +* You should have received a copy of the GNU General Public License along with +* this program. If not, see <http://www.gnu.org/licenses/>. +*/ +#include <common.h> +#include <driver.h> +#include <init.h> +#include <sizes.h> + +#include <asm/memory.h> + +static struct resource smp_twd_resource = { + .name ="smp_twd_base" , + .start =0xF8F00600 , + .end =0xF8F00610 , + .flags =IORESOURCE_MEM , +}; + +static struct device_d zynq_smp_twd = { + .id =DEVICE_ID_DYNAMIC , + .name ="smp_twd" , + .num_resources =1 , + .resource = &smp_twd_resource, +}; + +static struct resource zynq_serial_resource = { + .name ="zynq_serial_base" , + .start =0xE0001000 , + .end =0xE0001048 , + .flags =IORESOURCE_MEM , +}; +Quoted 8 lines
arch/arm/boards/zynq-zc702/devices.c line 49
Quoted 6 lines
arch/arm/boards/zynq-zc702/devices.c new file +6
-0+static struct device_d zynq_serial = { + .id =DEVICE_ID_DYNAMIC , + .name ="zynq_serial" , + .num_resources =1 , + .resource = &zynq_serial_resource, +};use generic code to register the devices
Quoted 2 lines
I'm assuming you're referring to
add_generic_device()and friends. I'll look into it.
yes as we plan the add a platform_device and driver struct in the feature so use add_generic_device will simplify the switch
as now you need to use a specific bus for all the device as example etc...
Quoted 33 lines
[..]
Quoted 22 lines
Quoted 22 lines
+++
b/arch/arm/boards/zynq-zc702/lowlevel.carch/arm/boards/zynq-zc702/devices.c new file +20
-0@@ -0,0 +1,28 @@ +/* +* Copyright (c) 2013 Josh Cartwright <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms and conditions of the GNU General Public License, +* version 2, as published by the Free Software Foundation. +* +* This program is distributed in the hope it will be useful, but WITHOUT +* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or +* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for +* more details. +* +* You should have received a copy of the GNU General Public License along with +* this program. If not, see <http://www.gnu.org/licenses/>. +*/ +#include <common.h> +#include <init.h> +#include <asm/barebox-arm.h> +#include <asm/barebox-arm-head.h> +Quoted 8 lines
arch/arm/boards/zynq-zc702/devices.c line 27
Quoted 7 lines
arch/arm/boards/zynq-zc702/devices.c new file +7
-0+#include <mach/slcr.h> + +void __naked __bare_init barebox_arm_reset_vector(void) +{ +slcr_unlock (); +arm_cpu_lowlevel_init (); +barebox_arm_entry (0x8000 ,SZ_128M ,0 );can you detect the ddr size
Quoted 1 line
I don't think this is possible, but I'll look a bit more.
you do not have a ddr controller?
or a i2c controller to read the eeprom?
Quoted 17 lines
Quoted 8 lines
Quoted 8 lines
arch/arm/boards/zynq-zc702/devices.c new file +1
-0+}arch/arm/mach-zynq/Kconfig +0
-0@@ -1,3 +1,22 @@ if ARCH_ZYNQQuoted 8 lines
arch/arm/mach-zynq/Kconfig line 9
Quoted 7 lines
arch/arm/mach-zynq/Kconfig +7
-0+config ARCH_TEXT_BASE + hex + default 0x04000000 if MACH_ZYNQ_ZC702 + +config ZYNQ_PS_CLK_FREQ + int + default 33333330 if MACH_ZYNQ_ZC702move it to C
Quoted 5 lines
Will-do.
Thanks again,
Josh
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Hi!
Quoted 8 lines · Josh Cartwright
In San Francisco a couple weeks ago (ELC2013), Thomas Petazzoni informally mentioned barebox in passing, so I decided to toy with it a bit...
This patchset adds basic support for the Zynq SoC to barebox. So far, it's only been tested as a 'secondary' bootloader (after u-boot). Also added is support for the zc702 development board.
I have some patches laying around, that have support for booting first stage from a SD-Card on a ZedBoard. I didn't send them as of yet, because I'm not completely satisfied with them in one or two places. (The clocksource seems to be inverse to what barebox expects, which would be a quick fix, and barebox boots uuultra slow, if I do everything according to the TRM)
At the moment, I do not have access to the board though. But I hope I can get a hand on it in the next days.
What I do not have atm is the clkdev stuff, that you already have.
Regards,
Steffen
Quoted 51 lines
The first two patches are simple typos I found getting acclimated to the barebox source.
Josh Cartwright (5):
trivial: doc: fix typos in mach-arm.dox
defaultenv: fixed mismatched braces in bin/boot
ARM: zynq: add driver for Zynq uarts
ARM: zynq: add support for Zynq 7000 SoC
ARM: zynq: add support for zc702 development boardarch/arm/Kconfig | 9 + arch/arm/Makefile | 2 + arch/arm/boards/zynq-zc702/Makefile | 1 + arch/arm/boards/zynq-zc702/config.h | 0 arch/arm/boards/zynq-zc702/devices.c | 70 ++++++ arch/arm/boards/zynq-zc702/lowlevel.c | 28 +++ arch/arm/mach-arm.dox | 4 +- arch/arm/mach-zynq/Kconfig | 22 ++ arch/arm/mach-zynq/Makefile | 1 + arch/arm/mach-zynq/clocks.c | 341 +++++++++++++++++++++++++++++ arch/arm/mach-zynq/include/mach/clkdev.h | 7 + arch/arm/mach-zynq/include/mach/debug_ll.h | 21 ++ arch/arm/mach-zynq/include/mach/slcr.h | 26 +++ arch/arm/mach-zynq/reset.c | 28 +++ defaultenv/bin/boot | 2 +- drivers/serial/Kconfig | 6 + drivers/serial/Makefile | 1 + drivers/serial/serial_zynq.c | 144 ++++++++++++ 18 files changed, 710 insertions(+), 3 deletions(-) create mode 100644 arch/arm/boards/zynq-zc702/Makefile create mode 100644 arch/arm/boards/zynq-zc702/config.h create mode 100644 arch/arm/boards/zynq-zc702/devices.c create mode 100644 arch/arm/boards/zynq-zc702/lowlevel.c create mode 100644 arch/arm/mach-zynq/Kconfig create mode 100644 arch/arm/mach-zynq/Makefile create mode 100644 arch/arm/mach-zynq/clocks.c create mode 100644 arch/arm/mach-zynq/include/mach/clkdev.h create mode 100644 arch/arm/mach-zynq/include/mach/debug_ll.h create mode 100644 arch/arm/mach-zynq/include/mach/slcr.h create mode 100644 arch/arm/mach-zynq/reset.c create mode 100644 drivers/serial/serial_zynq.cSignature · 7 lines
1.8.1.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Quoted 12 lines · Steffen Trumtrar
Hi!
Quoted 8 lines · Josh Cartwright
In San Francisco a couple weeks ago (ELC2013), Thomas Petazzoni informally mentioned barebox in passing, so I decided to toy with it a bit...
This patchset adds basic support for the Zynq SoC to barebox. So far, it's only been tested as a 'secondary' bootloader (after u-boot). Also added is support for the zc702 development board.
Quoted 7 lines
I have some patches laying around, that have support for booting first stage from a SD-Card on a ZedBoard. I didn't send them as of yet, because I'm not completely satisfied with them in one or two places. (The clocksource seems to be inverse to what barebox expects, which would be a quick fix, and barebox boots uuultra slow, if I do everything according to the TRM)
At the moment, I do not have access to the board though. But I hope I can get a hand on it in the next days.
If you have a chance to send out what you have, I'd be curious to see it. Fortunately I have several Zynq boards to play with.
Josh
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Quoted 21 lines · Josh Cartwright
Quoted 12 lines · Steffen Trumtrar
Hi!
Quoted 8 lines · Josh Cartwright
In San Francisco a couple weeks ago (ELC2013), Thomas Petazzoni informally mentioned barebox in passing, so I decided to toy with it a bit...
This patchset adds basic support for the Zynq SoC to barebox. So far, it's only been tested as a 'secondary' bootloader (after u-boot). Also added is support for the zc702 development board.
Quoted 7 lines
I have some patches laying around, that have support for booting first stage from a SD-Card on a ZedBoard. I didn't send them as of yet, because I'm not completely satisfied with them in one or two places. (The clocksource seems to be inverse to what barebox expects, which would be a quick fix, and barebox boots uuultra slow, if I do everything according to the TRM)
At the moment, I do not have access to the board though. But I hope I can get a hand on it in the next days.
Quoted 3 lines
If you have a chance to send out what you have, I'd be curious to see it. Fortunately I have several Zynq boards to play with.
Hi!
Have a look at
http://git.pengutronix.de/?p=str/barebox.git;a=summary
I "stole" your clk driver and added it to my patch stack :-) Current state for ZedBoard:
- boot first stage from SD-Card
- barebox.bin needs to be processed with ./scripts/zynq_checksum barebox.bin BOOT.bin to have the checksum in the BootROM header
- clocksource is arm_smp_tmd at seems accurate
- the BootROM needs about 4-5 seconds to copy barebox from SD to the OCM. I guess, I need to mess with the SD setup in the BootROM somehow
- just enough clkdev to use the timer
- all pinctrl, clk setup etc happens in the lowlevel init
Regards,
Steffen
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Quoted 1 line · Steffen Trumtrar
On Tue, Mar 05, 2013 at 11:09:29AM -0600, Josh Cartwright wrote:
[..]
Quoted 17 lines
Quoted 11 lines
Quoted 7 lines
I have some patches laying around, that have support for booting first stage from a SD-Card on a ZedBoard. I didn't send them as of yet, because I'm not completely satisfied with them in one or two places. (The clocksource seems to be inverse to what barebox expects, which would be a quick fix, and barebox boots uuultra slow, if I do everything according to the TRM)
At the moment, I do not have access to the board though. But I hope I can get a hand on it in the next days.If you have a chance to send out what you have, I'd be curious to see it. Fortunately I have several Zynq boards to play with.
Hi!
Have a look at
http://git.pengutronix.de/?p=str/barebox.git;a=summary
Quoted 12 lines
I "stole" your clk driver and added it to my patch stack :-) Current state for ZedBoard:
- boot first stage from SD-Card
- barebox.bin needs to be processed with./scripts/zynq_checksumbarebox.bin BOOT.bin to have the checksum in the BootROM header
- clocksource isarm_smp_tmdat seems accurate
- the BootROM needs about 4-5 seconds to copy barebox from SD to the OCM. I guess, I need to mess with the SD setup in the BootROM somehow
- just enough clkdev to use the timer
- all pinctrl, clk setup etc happens in the lowlevel init
Hey Steffen-
Thanks for sharing this! I'll be looking to get board support for the zc702 on top of your work this weekend (I have several Zynq boards, but none of them are ZedBoards). I'm also in the process of porting the uboot zynq_gem driver.
Do you have plans for submitting this to the list?
Thanks again,
Josh
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Quoted 20 lines · Josh Cartwright
Quoted 1 line · Steffen Trumtrar
On Tue, Mar 05, 2013 at 11:09:29AM -0600, Josh Cartwright wrote:
[..]
Quoted 17 lines
Quoted 11 lines
Quoted 7 lines
I have some patches laying around, that have support for booting first stage from a SD-Card on a ZedBoard. I didn't send them as of yet, because I'm not completely satisfied with them in one or two places. (The clocksource seems to be inverse to what barebox expects, which would be a quick fix, and barebox boots uuultra slow, if I do everything according to the TRM)
At the moment, I do not have access to the board though. But I hope I can get a hand on it in the next days.If you have a chance to send out what you have, I'd be curious to see it. Fortunately I have several Zynq boards to play with.
Hi!
Have a look at
http://git.pengutronix.de/?p=str/barebox.git;a=summary
Quoted 12 lines
Quoted 4 lines
I "stole" your clk driver and added it to my patch stack :-) Current state for ZedBoard:
- boot first stage from SD-Card
- barebox.bin needs to be processed withQuoted 8 lines
./scripts/zynq_checksumbarebox.bin BOOT.bin to have the checksum in the BootROM header
- clocksource isarm_smp_tmdat seems accurate
- the BootROM needs about 4-5 seconds to copy barebox from SD to the OCM. I guess, I need to mess with the SD setup in the BootROM somehow
- just enough clkdev to use the timer
- all pinctrl, clk setup etc happens in the lowlevel init
Hi Josh!
Quoted 7 lines
Hey Steffen-
Thanks for sharing this! I'll be looking to get board support for the zc702 on top of your work this weekend (I have several Zynq boards, but none of them are ZedBoards). I'm also in the process of porting the uboot
zynq_gemdriver.
First, \o/. I don't know how the two differ. But I would guess, that you can pretty much copy the lowlevel stuff et al.
Only the DDR timing stuff may make problems.
Second: No! Don't! I'm trying to get drivers/net/macb.c running on Zynq. As far as I can tell at the moment, this is a driver for a Cadence IP gem. And the zynq uses exactly that IP core. Alas, I have problems with the dma_alloc_coherent call in its probe function.
The same goes for the UART driver and other cores. We should not start developing Xilinx drivers for everything, if in reality we have IP cores from other providers.
The same goes for Linux. I haven't managed to boot mainline linux yet, but I saw that there are multiple bindings and drivers for Xilinx. And the TRM clearly states, that WDT, GEM, SPI, UART and TTC are all Cadence IP cores.
Quoted 1 line
Do you have plans for submitting this to the list?
Yes, definitely! I need to cleanup the patches a little and want to be sure that I didn't do anything stupidly wrong. The problem with dma_alloc is at least a hint, that I maybe did.
Regards,
Steffen
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Hi,
2013/3/8 Steffen Trumtrar <[email protected]>:
Quoted 21 lines · Josh Cartwright
Quoted 20 lines · Steffen Trumtrar
Quoted 1 line · Josh Cartwright
[..]
Quoted 17 lines
Quoted 11 lines
Quoted 7 lines
I have some patches laying around, that have support for booting first stage from a SD-Card on a ZedBoard. I didn't send them as of yet, because I'm not completely satisfied with them in one or two places. (The clocksource seems to be inverse to what barebox expects, which would be a quick fix, and barebox boots uuultra slow, if I do everything according to the TRM)
At the moment, I do not have access to the board though. But I hope I can get a hand on it in the next days.If you have a chance to send out what you have, I'd be curious to see it. Fortunately I have several Zynq boards to play with.
Hi!
Have a look at
http://git.pengutronix.de/?p=str/barebox.git;a=summary
Quoted 12 lines
Quoted 4 lines
Quoted 4 lines
I "stole" your clk driver and added it to my patch stack :-) Current state for ZedBoard:
- boot first stage from SD-Card
- barebox.bin needs to be processed withQuoted 8 lines
Quoted 8 lines
./scripts/zynq_checksumbarebox.bin BOOT.bin to have the checksum in the BootROM header
- clocksource isarm_smp_tmdat seems accurate
- the BootROM needs about 4-5 seconds to copy barebox from SD to the OCM. I guess, I need to mess with the SD setup in the BootROM somehow
- just enough clkdev to use the timer
- all pinctrl, clk setup etc happens in the lowlevel init
Nice. What's the difference between this barebox and u-boot? I remember that discussion on u-boot mailing list. Is it just that Kconfig stuff and driver initialization?
What about DT support? Initialized u-boot from device tree? Is it there?
Quoted 8 lines
Quoted 4 lines
Thanks for sharing this! I'll be looking to get board support for the zc702 on top of your work this weekend (I have several Zynq boards, but none of them are ZedBoards). I'm also in the process of porting the uboot
zynq_gemdriver.First, \o/. I don't know how the two differ. But I would guess, that you can pretty much copy the lowlevel stuff et al.
Only the DDR timing stuff may make problems.
Difference is only in connection out of chip. How barebox handle this? Serial IP selections, ddr size, mmc, etc.
Quoted 5 lines
Second: No! Don't! I'm trying to get
drivers/net/macb.crunning on Zynq. As far as I can tell at the moment, this is a driver for a Cadence IP gem. And the zynq uses exactly that IP core. Alas, I have problems with thedma_alloc_coherentcall in its probe function.
Nice. I will look forward on input from this. We need to use this IP in linux kernel too.
Quoted 4 lines
The same goes for the UART driver and other cores. We should not start developing Xilinx drivers for everything, if in reality we have IP cores from other providers.
definitely.
Quoted 4 lines
The same goes for Linux. I haven't managed to boot mainline linux yet, but I saw that there are multiple bindings and drivers for Xilinx. And the TRM clearly states, that WDT, GEM, SPI, UART and TTC are all Cadence IP cores.
yep, pl330, cadence gem, spi not sure, wdt also not sure, xilinx uart is in the mainline
and none reports that there is cadence serial driver too. TTC is also news for me.
If you can point me to them, that will be great.
Quoted 5 lines
Quoted 1 line
Do you have plans for submitting this to the list?
Yes, definitely! I need to cleanup the patches a little and want to be sure that I didn't do anything stupidly wrong. The problem with
dma_allocis at least a hint, that I maybe did.
Nice discussion. Would like to look at it with you but
Hopefully next next week I will have more time to look at your patches and try it.
Thanks,
Michal
Signature · 10 lines
Michal Simek, Ing. (M.Eng) w: www.monstr.eu p: +42-0-721842854 Maintainer of Linux kernel - Microblaze cpu - http://www.monstr.eu/fdt/ Maintainer of Linux kernel - Xilinx Zynq ARM architecture Microblaze U-BOOT custodian and responsible for u-boot arm zynq platform _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Hi,
Quoted 37 lines · Michal Simek
Hi,
2013/3/8 Steffen Trumtrar <[email protected]>:
Quoted 21 lines · Josh Cartwright
Quoted 20 lines · Steffen Trumtrar
Quoted 1 line · Josh Cartwright
[..]
Quoted 17 lines
Quoted 11 lines
Quoted 7 lines
I have some patches laying around, that have support for booting first stage from a SD-Card on a ZedBoard. I didn't send them as of yet, because I'm not completely satisfied with them in one or two places. (The clocksource seems to be inverse to what barebox expects, which would be a quick fix, and barebox boots uuultra slow, if I do everything according to the TRM)
At the moment, I do not have access to the board though. But I hope I can get a hand on it in the next days.If you have a chance to send out what you have, I'd be curious to see it. Fortunately I have several Zynq boards to play with.
Hi!
Have a look at
http://git.pengutronix.de/?p=str/barebox.git;a=summaryQuoted 12 lines
Quoted 4 lines
Quoted 4 lines
I "stole" your clk driver and added it to my patch stack :-) Current state for ZedBoard:
- boot first stage from SD-Card
- barebox.bin needs to be processed withQuoted 8 lines
Quoted 8 lines
./scripts/zynq_checksumbarebox.bin BOOT.bin to have the checksum in the BootROM header
- clocksource isarm_smp_tmdat seems accurate
- the BootROM needs about 4-5 seconds to copy barebox from SD to the OCM. I guess, I need to mess with the SD setup in the BootROM somehow
- just enough clkdev to use the timer
- all pinctrl, clk setup etc happens in the lowlevel init
Quoted 7 lines
Nice. What's the difference between this barebox and u-boot? I remember that discussion on u-boot mailing list. Is it just that
Kconfigstuff and driver initialization?What about DT support? Initialized u-boot from device tree? Is it there?
Well, I don't actually know, what u-boot can do, as I do not follow it. barebox uses Kconfig, the linux driver model, a lot less #ifdefs, has support for a compressed bootloader, that extracts itself, the environment system is IHMO way better than in u-boot, a menu, where you can select the bootsource etc, you can boot images via tftp with "bootm /mnt/tftp/zImage", you can boot zImage, uImage, ... with appended DT, with separate DT, there is support for DT probing of devices.
What I like the most: if you know linux kernel and its structure, you know barebox and its structure (well, mostly).
Quoted 11 lines
Quoted 9 lines
Quoted 5 lines
Thanks for sharing this! I'll be looking to get board support for the zc702 on top of your work this weekend (I have several Zynq boards, but none of them are ZedBoards). I'm also in the process of porting the uboot
zynq_gemdriver.First, \o/. I don't know how the two differ. But I would guess, that you can pretty much copy the lowlevel stuff et al.
Only the DDR timing stuff may make problems.Difference is only in connection out of chip. How barebox handle this?
barebox has /arch/arm/boards/avnet-zedboard/board.c, here you can define the boardspecific pincontrol etc. Well, like the platformcode in the kernel. For the zynq there is no pinctrl driver though, as I have to write it first :-)
Clocks are handled like in linux. With clockdev and clocktree.
ATM this is all hardcoded in the lowlevel init.
Quoted 24 lines
Serial IP selections, ddr size, mmc, etc.
Quoted 5 lines
Second: No! Don't! I'm trying to get
drivers/net/macb.crunning on Zynq. As far as I can tell at the moment, this is a driver for a Cadence IP gem. And the zynq uses exactly that IP core. Alas, I have problems with thedma_alloc_coherentcall in its probe function.Nice. I will look forward on input from this. We need to use this IP in linux kernel too.
Quoted 4 lines
The same goes for the UART driver and other cores. We should not start developing Xilinx drivers for everything, if in reality we have IP cores from other providers.
definitely.
Quoted 4 lines
The same goes for Linux. I haven't managed to boot mainline linux yet, but I saw that there are multiple bindings and drivers for Xilinx. And the TRM clearly states, that WDT, GEM, SPI, UART and TTC are all Cadence IP cores.
Quoted 6 lines
yep, pl330, cadence gem, spi not sure, wdt also not sure, xilinx uart is in the mainline
and none reports that there is cadence serial driver too. TTC is also news for me.
If you can point me to them, that will be great.
Well, I don't know if there are drivers for all those IPs, but if there aren't any, they should be called cadence-something with the according bindings. Oh, and Arasan-something for the SD-Controller.
Well, maybe those IPs are even not really developed by Cadence and compatible to other drivers, who knows.
For the Synopsys USB controller you might want to take a look at the ChipIdea driver (ci13xxx-something). It is the same core ;-)
Quoted 12 lines
Quoted 6 lines
Quoted 2 lines
Do you have plans for submitting this to the list?
Yes, definitely! I need to cleanup the patches a little and want to be sure that I didn't do anything stupidly wrong. The problem with
dma_allocis at least a hint, that I maybe did.Nice discussion. Would like to look at it with you but
Hopefully next next week I will have more time to look at your patches and try it.
Regards and nice weekend,
Steffen
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Quoted 47 lines · Steffen Trumtrar
Quoted 20 lines · Josh Cartwright
Quoted 1 line · Steffen Trumtrar
On Tue, Mar 05, 2013 at 11:09:29AM -0600, Josh Cartwright wrote:
[..]
Quoted 17 lines
Quoted 11 lines
Quoted 7 lines
I have some patches laying around, that have support for booting first stage from a SD-Card on a ZedBoard. I didn't send them as of yet, because I'm not completely satisfied with them in one or two places. (The clocksource seems to be inverse to what barebox expects, which would be a quick fix, and barebox boots uuultra slow, if I do everything according to the TRM)
At the moment, I do not have access to the board though. But I hope I can get a hand on it in the next days.If you have a chance to send out what you have, I'd be curious to see it. Fortunately I have several Zynq boards to play with.
Hi!
Have a look at
http://git.pengutronix.de/?p=str/barebox.git;a=summaryQuoted 12 lines
Quoted 4 lines
I "stole" your clk driver and added it to my patch stack :-) Current state for ZedBoard:
- boot first stage from SD-Card
- barebox.bin needs to be processed withQuoted 8 lines
./scripts/zynq_checksumbarebox.bin BOOT.bin to have the checksum in the BootROM header
- clocksource isarm_smp_tmdat seems accurate
- the BootROM needs about 4-5 seconds to copy barebox from SD to the OCM. I guess, I need to mess with the SD setup in the BootROM somehow
- just enough clkdev to use the timer
- all pinctrl, clk setup etc happens in the lowlevel initHi Josh!
Quoted 6 lines
Hey Steffen-
Thanks for sharing this! I'll be looking to get board support for the zc702 on top of your work this weekend (I have several Zynq boards, but none of them are ZedBoards). I'm also in the process of porting the uboot
zynq_gemdriver.First, \o/. I don't know how the two differ. But I would guess, that you can pretty much copy the lowlevel stuff et al.
Only the DDR timing stuff may make problems.
Quoted 5 lines
Second: No! Don't! I'm trying to get
drivers/net/macb.crunning on Zynq. As far as I can tell at the moment, this is a driver for a Cadence IP gem. And the zynq uses exactly that IP core. Alas, I have problems with thedma_alloc_coherentcall in its probe function.
Doh! I certainly did not want to duplicate a driver unnecessarily. I'll keep this in mind going forward.
Quoted 3 lines
The same goes for the UART driver and other cores. We should not start developing Xilinx drivers for everything, if in reality we have IP cores from other providers.
Absolutely.
Thanks,
Josh
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Quoted 48 lines · Josh Cartwright
Quoted 47 lines · Steffen Trumtrar
Quoted 20 lines · Josh Cartwright
Quoted 1 line · Steffen Trumtrar
On Tue, Mar 05, 2013 at 11:09:29AM -0600, Josh Cartwright wrote:
[..]
Quoted 17 lines
Quoted 11 lines
Quoted 7 lines
I have some patches laying around, that have support for booting first stage from a SD-Card on a ZedBoard. I didn't send them as of yet, because I'm not completely satisfied with them in one or two places. (The clocksource seems to be inverse to what barebox expects, which would be a quick fix, and barebox boots uuultra slow, if I do everything according to the TRM)
At the moment, I do not have access to the board though. But I hope I can get a hand on it in the next days.If you have a chance to send out what you have, I'd be curious to see it. Fortunately I have several Zynq boards to play with.
Hi!
Have a look at
http://git.pengutronix.de/?p=str/barebox.git;a=summaryQuoted 12 lines
Quoted 4 lines
I "stole" your clk driver and added it to my patch stack :-) Current state for ZedBoard:
- boot first stage from SD-Card
- barebox.bin needs to be processed withQuoted 8 lines
./scripts/zynq_checksumbarebox.bin BOOT.bin to have the checksum in the BootROM header
- clocksource isarm_smp_tmdat seems accurate
- the BootROM needs about 4-5 seconds to copy barebox from SD to the OCM. I guess, I need to mess with the SD setup in the BootROM somehow
- just enough clkdev to use the timer
- all pinctrl, clk setup etc happens in the lowlevel initHi Josh!
Quoted 6 lines
Hey Steffen-
Thanks for sharing this! I'll be looking to get board support for the zc702 on top of your work this weekend (I have several Zynq boards, but none of them are ZedBoards). I'm also in the process of porting the uboot
zynq_gemdriver.First, \o/. I don't know how the two differ. But I would guess, that you can pretty much copy the lowlevel stuff et al.
Only the DDR timing stuff may make problems.
Quoted 9 lines
Quoted 5 lines
Second: No! Don't! I'm trying to get
drivers/net/macb.crunning on Zynq. As far as I can tell at the moment, this is a driver for a Cadence IP gem. And the zynq uses exactly that IP core. Alas, I have problems with thedma_alloc_coherentcall in its probe function.Doh! I certainly did not want to duplicate a driver unnecessarily. I'll keep this in mind going forward.
Just a quick note: it seems that the macb can be used. I didn't manage to get a connection yet. But I can talk to the phy, get a link etc.
So, the linux macb driver should work two.
Regards,
Steffen
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Quoted 48 lines · Steffen Trumtrar
Quoted 20 lines · Josh Cartwright
Quoted 1 line · Steffen Trumtrar
On Tue, Mar 05, 2013 at 11:09:29AM -0600, Josh Cartwright wrote:
[..]
Quoted 17 lines
Quoted 11 lines
Quoted 7 lines
I have some patches laying around, that have support for booting first stage from a SD-Card on a ZedBoard. I didn't send them as of yet, because I'm not completely satisfied with them in one or two places. (The clocksource seems to be inverse to what barebox expects, which would be a quick fix, and barebox boots uuultra slow, if I do everything according to the TRM)
At the moment, I do not have access to the board though. But I hope I can get a hand on it in the next days.If you have a chance to send out what you have, I'd be curious to see it. Fortunately I have several Zynq boards to play with.
Hi!
Have a look at
http://git.pengutronix.de/?p=str/barebox.git;a=summaryQuoted 12 lines
Quoted 4 lines
I "stole" your clk driver and added it to my patch stack :-) Current state for ZedBoard:
- boot first stage from SD-Card
- barebox.bin needs to be processed withQuoted 8 lines
./scripts/zynq_checksumbarebox.bin BOOT.bin to have the checksum in the BootROM header
- clocksource isarm_smp_tmdat seems accurate
- the BootROM needs about 4-5 seconds to copy barebox from SD to the OCM. I guess, I need to mess with the SD setup in the BootROM somehow
- just enough clkdev to use the timer
- all pinctrl, clk setup etc happens in the lowlevel initHi Josh!
Quoted 7 lines
Hey Steffen-
Thanks for sharing this! I'll be looking to get board support for the zc702 on top of your work this weekend (I have several Zynq boards, but none of them are ZedBoards). I'm also in the process of porting the uboot
zynq_gemdriver.First, \o/. I don't know how the two differ. But I would guess, that you can pretty much copy the lowlevel stuff et al.
Only the DDR timing stuff may make problems.
Quoted 5 lines
Second: No! Don't! I'm trying to get
drivers/net/macb.crunning on Zynq. As far as I can tell at the moment, this is a driver for a Cadence IP gem. And the zynq uses exactly that IP core. Alas, I have problems with thedma_alloc_coherentcall in its probe function.
this should not give you any trouble execpt if you do not able the l2cache correctly
I did the port and test that drivers on Cortex-A5 and Nicolas and I work on it to share the code with the kernel
U-Boot does not implement it correctly anyway
Best Regards,
J.
Quoted 10 lines
The same goes for the UART driver and other cores. We should not start developing Xilinx drivers for everything, if in reality we have IP cores from other providers.
The same goes for Linux. I haven't managed to boot mainline linux yet, but I saw that there are multiple bindings and drivers for Xilinx. And the TRM clearly states, that WDT, GEM, SPI, UART and TTC are all Cadence IP cores.
Quoted 19 lines
Quoted 1 line
Do you have plans for submitting this to the list?
Yes, definitely! I need to cleanup the patches a little and want to be sure that I didn't do anything stupidly wrong. The problem with
dma_allocis at least a hint, that I maybe did.Regards,
SteffenSignature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox