powerpc/t4240qds: Add board detail for bdinfo command
PATCH 2/21 powerpc/t4240qds: Add board detail for bdinfo command
Print more detail information including core voltage, RCW source, switch settings, etc. with bdinfo command.
Signed-off-by York Sun <[email protected]>
--- board/freescale/t4qds/t4qds.c | 100 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 100 insertions(+)
board/freescale/t4qds/t4qds.c +100 -0
@@ -644,6 +644,106 @@ void ft_board_setup(void *blob, bd_t *bd) }/* +* This function is called by bdinfo to print detail board information. +* As an exmaple for future board, we organize the messages into +* several sections. If applicable, the message is in the format of +* <name> = <value> +* It should aligned with normal output of bdinfo command. +* +* Voltage: Core, DDR and another configurable voltages +* Clock : Critical clocks which are not printed already +* RCW : RCW source if not printed already +* Misc : Other important information not in above catagories +*/ +void board_detail (void ) +{ +int i; +u8 brdcfg[16 ], dutcfg[16 ], rst_ctl; +int vdd, rcwsrc; +static const char *const clk[] = {"66.67" ,"100" ,"125" ,"133.33" }; + +for (i =0 ; i <16 ; i++) { + brdcfg[i] = qixis_read(offsetof(struct qixis, brdcfg[0]) + i); + dutcfg[i] = qixis_read(offsetof(struct qixis, dutcfg[0]) + i); + } + +/* Voltage secion */ +if (!select_i2c_ch_pca9547 (I2C_MUX_CH_VOL_MONITOR )) { + vdd =read_voltage (); +if (vdd >0 ) +printf ("Core voltage= %d mV\n" , vdd); +select_i2c_ch_pca9547 (I2C_MUX_CH_DEFAULT ); + } + +printf ("XVDD = 1.%d V\n" , ((brdcfg[8 ] &0xf ) -4 ) *5 +25 ); + +/* clock section */ +printf ("SYSCLK = %s MHz\nDDRCLK = %s MHz\n" , + clk[(brdcfg[11 ] >>2 ) &0x3 ], clk[brdcfg[11 ] &3 ]); + +/* RCW section */ + rcwsrc = (dutcfg[0 ] <<1 ) + (dutcfg[1 ] &1 ); +puts ("RCW source = " ); +switch (rcwsrc) { +case 0x017 : +case 0x01f : +puts ("8-bit NOR\n" ); +break ; +case 0x027 : +case 0x02F : +puts ("16-bit NOR\n" ); +break ; +case 0x040 : +puts ("SDHC/eMMC\n" ); +break ; +case 0x044 : +puts ("SPI 16-bit addressing\n" ); +break ; +case 0x045 : +puts ("SPI 24-bit addressing\n" ); +break ; +case 0x048 : +puts ("I2C normal addressing\n" ); +break ; +case 0x049 : +puts ("I2C extended addressing\n" ); +break ; +case 0x108 : +case 0x109 : +case 0x10a : +case 0x10b : +puts ("8-bit NAND, 2KB\n" ); +break ; +default : +if ((rcwsrc >=0x080 ) && (rcwsrc <=0x09f )) +puts ("Hard-coded RCW\n" ); +else if ((rcwsrc >=0x110 ) && (rcwsrc <=0x11f )) +puts ("8-bit NAND, 4KB\n" ); +else +puts ("unknown\n" ); +break ; + } + +/* Misc section */ + rst_ctl =QIXIS_READ (rst_ctl); +puts ("HRESET_REQ = " ); +switch (rst_ctl &0x30 ) { +case 0x00 : +puts ("Ignored\n" ); +break ; +case 0x10 : +puts ("Assert HRESET\n" ); +break ; +case 0x30 : +puts ("Reset system\n" ); +break ; +default : +puts ("N/A\n" ); +break ; + } +} + +/* * Reverse engineering switch settings. * Some bits cannot be figured out. They will be displayed as * underscore in binary format. mask[] has those bits.
Signature · 1 line
1.7.9.5
PATCH 2/21 powerpc/t4240qds: Add board detail for bdinfo command
Dear York Sun,
Quoted 7 lines · In message <[email protected]> you wrote:
Print more detail information including core voltage, RCW source, switch settings, etc. with bdinfo command.
Signed-off-by York Sun <[email protected]>--- board/freescale/t4qds/t4qds.c | 100 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 100 insertions(+)
CHECK: Alignment should match open parenthesis
#119: FILE: board/freescale/t4qds/t4qds.c:682:
+ printf("SYSCLK = %s MHz\nDDRCLK = %s MHz\n",
+ clk[(brdcfg[11] >> 2) & 0x3], clk[brdcfg[11] & 3]);
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de "If God had wanted us to use the metric system, Jesus would have had 10 apostles."