rename sunxi clock compatible strings
Subsystems (4)
Emilio López
maintainercover rename sunxi clock compatible strings
Hi,
As discussed with Maxime, we decided to rename the compatible strings to sun4i, to keep it coherent when support for sun6i and newer is introduced. See "ARM: sunxi: Architecture cleanups and rework" and these patch messages for the full rationale.
I will be sending a v2 of "clk: sunxi: gates support" soon, using sun4i compatible strings, based on these two patches.
Thanks,
Emilio
Emilio L?pez (2):
clk: sunxi: rename compatible strings
arm: sunxi: rename clock compatible strings
Emilio López
maintainerPATCH 1/2 clk: sunxi: rename compatible strings
During the introduction of the Allwinner SoC platforms, sunxi was initially meant as a generic name for all the variants of the Allwinner SoC.
It was ok at the time of the support of only the A10 and A13 that look pretty much the same; but it's beginning to be troublesome with the future addition of the Allwinner A31 (sun6i) that is quite different, and would introduce some weird logic, where sunxi would actually mean in some case sun4i and sun5i but without sun6i...
Moreover, it makes the compatible strings naming scheme not consistent with other architectures, where usually for this kind of compability, we just use the oldest SoC name that has this IP, so let's do just this.
---
These compatible strings have never been on a released kernel, so changing them now shouldn't cause any issues. Also see Maxime's "ARM: sunxi: Architecture cleanups and rework" which does the same for the rest of sunxi code.
Documentation/devicetree/bindings/clock/sunxi.txt | 22 +++++++++++----------- drivers/clk/sunxi/clk-sunxi.c | 16 ++++++++-------- 2 files changed, 19 insertions(+), 19 deletions(-)
Documentation/devicetree/bindings/clock/sunxi.txt +11 -11
@@ -6,14 +6,14 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be one of the following: - "allwinner,sunxi-osc-clk" - for a gatable oscillator - "allwinner,sunxi-pll1-clk" - for the main PLL clock - "allwinner,sunxi-cpu-clk" - for the CPU multiplexer clock - "allwinner,sunxi-axi-clk" - for the sunxi AXI clock - "allwinner,sunxi-ahb-clk" - for the sunxi AHB clock - "allwinner,sunxi-apb0-clk" - for the sunxi APB0 clock - "allwinner,sunxi-apb1-clk" - for the sunxi APB1 clock - "allwinner,sunxi-apb1-mux-clk" - for the sunxi APB1 clock muxing + "allwinner,sun4i-osc-clk" - for a gatable oscillator + "allwinner,sun4i-pll1-clk" - for the main PLL clock + "allwinner,sun4i-cpu-clk" - for the CPU multiplexer clock + "allwinner,sun4i-axi-clk" - for the AXI clock + "allwinner,sun4i-ahb-clk" - for the AHB clock + "allwinner,sun4i-apb0-clk" - for the APB0 clock + "allwinner,sun4i-apb1-clk" - for the APB1 clock + "allwinner,sun4i-apb1-mux-clk" - for the APB1 clock muxing Required properties for all clocks: - reg : shall be the control register address for the clock.
@@ -24,21 +24,21 @@ For example: osc24M: osc24M at 01c20050 { #clock-cells = <0>; - compatible = "allwinner,sunxi-osc-clk"; + compatible = "allwinner,sun4i-osc-clk"; reg = <0x01c20050 0x4>; clocks = <&osc24M_fixed>; }; pll1: pll1 at 01c20000 { #clock-cells = <0>; - compatible = "allwinner,sunxi-pll1-clk"; + compatible = "allwinner,sun4i-pll1-clk"; reg = <0x01c20000 0x4>; clocks = <&osc24M>; }; cpu: cpu at 01c20054 { #clock-cells = <0>; - compatible = "allwinner,sunxi-cpu-clk"; + compatible = "allwinner,sun4i-cpu-clk"; reg = <0x01c20054 0x4>; clocks = <&osc32k>, <&osc24M>, <&pll1>; };
drivers/clk/sunxi/clk-sunxi.c +8 -8
@@ -305,29 +305,29 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,/* Matches for of_clk_init */ static const __initconst struct of_device_id clk_match[] = { {.compatible ="fixed-clock" , .data = of_fixed_clk_setup,}, - {.compatible ="allwinner,sunxi-osc-clk" , .data = sunxi_osc_clk_setup,}, + {.compatible ="allwinner,sun4i-osc-clk" , .data = sunxi_osc_clk_setup,}, {} };/* Matches for factors clocks */ static const __initconst struct of_device_id clk_factors_match[] = { - {.compatible ="allwinner,sunxi-pll1-clk" , .data = &pll1_data,}, - {.compatible ="allwinner,sunxi-apb1-clk" , .data = &apb1_data,}, + {.compatible ="allwinner,sun4i-pll1-clk" , .data = &pll1_data,}, + {.compatible ="allwinner,sun4i-apb1-clk" , .data = &apb1_data,}, {} };/* Matches for divider clocks */ static const __initconst struct of_device_id clk_div_match[] = { - {.compatible ="allwinner,sunxi-axi-clk" , .data = &axi_data,}, - {.compatible ="allwinner,sunxi-ahb-clk" , .data = &ahb_data,}, - {.compatible ="allwinner,sunxi-apb0-clk" , .data = &apb0_data,}, + {.compatible ="allwinner,sun4i-axi-clk" , .data = &axi_data,}, + {.compatible ="allwinner,sun4i-ahb-clk" , .data = &ahb_data,}, + {.compatible ="allwinner,sun4i-apb0-clk" , .data = &apb0_data,}, {} };/* Matches for mux clocks */ static const __initconst struct of_device_id clk_mux_match[] = { - {.compatible ="allwinner,sunxi-cpu-clk" , .data = &cpu_data,}, - {.compatible ="allwinner,sunxi-apb1-mux-clk" , .data = &apb1_mux_data,}, + {.compatible ="allwinner,sun4i-cpu-clk" , .data = &cpu_data,}, + {.compatible ="allwinner,sun4i-apb1-mux-clk" , .data = &apb1_mux_data,}, {} };
Signature · 1 line
1.8.2
PATCH 1/2 clk: sunxi: rename compatible strings
Quoting Emilio L?pez (2013-03-26 19:39:17)
Quoted 10 lines
During the introduction of the Allwinner SoC platforms, sunxi was initially meant as a generic name for all the variants of the Allwinner SoC.
It was ok at the time of the support of only the A10 and A13 that look pretty much the same; but it's beginning to be troublesome with the future addition of the Allwinner A31 (sun6i) that is quite different, and would introduce some weird logic, where sunxi would actually mean in some case sun4i and sun5i but without sun6i...
Quoted 5 lines
Moreover, it makes the compatible strings naming scheme not consistent with other architectures, where usually for this kind of compability, we just use the oldest SoC name that has this IP, so let's do just this.
Signed-off-by Emilio L?pez <[email protected]>
Which tree did you want this patch to go through?
Regards,
Mike
Quoted 107 lines
---
These compatible strings have never been on a released kernel, so changing them now shouldn't cause any issues. Also see Maxime's "ARM: sunxi: Architecture cleanups and rework" which does the same for the rest of sunxi code.
Documentation/devicetree/bindings/clock/sunxi.txt | 22 +++++++++++----------- drivers/clk/sunxi/clk-sunxi.c | 16 ++++++++-------- 2 files changed, 19 insertions(+), 19 deletions(-)Documentation/devicetree/bindings/clock/sunxi.txt +11
-11@@ -6,14 +6,14 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be one of the following: - "allwinner,sunxi-osc-clk" - for a gatable oscillator - "allwinner,sunxi-pll1-clk" - for the main PLL clock - "allwinner,sunxi-cpu-clk" - for the CPU multiplexer clock - "allwinner,sunxi-axi-clk" - for the sunxi AXI clock - "allwinner,sunxi-ahb-clk" - for the sunxi AHB clock - "allwinner,sunxi-apb0-clk" - for the sunxi APB0 clock - "allwinner,sunxi-apb1-clk" - for the sunxi APB1 clock - "allwinner,sunxi-apb1-mux-clk" - for the sunxi APB1 clock muxing + "allwinner,sun4i-osc-clk" - for a gatable oscillator + "allwinner,sun4i-pll1-clk" - for the main PLL clock + "allwinner,sun4i-cpu-clk" - for the CPU multiplexer clock + "allwinner,sun4i-axi-clk" - for the AXI clock + "allwinner,sun4i-ahb-clk" - for the AHB clock + "allwinner,sun4i-apb0-clk" - for the APB0 clock + "allwinner,sun4i-apb1-clk" - for the APB1 clock + "allwinner,sun4i-apb1-mux-clk" - for the APB1 clock muxing Required properties for all clocks: - reg : shall be the control register address for the clock.@@ -24,21 +24,21 @@ For example: osc24M: osc24M at 01c20050 { #clock-cells = <0>; - compatible = "allwinner,sunxi-osc-clk"; + compatible = "allwinner,sun4i-osc-clk"; reg = <0x01c20050 0x4>; clocks = <&osc24M_fixed>; }; pll1: pll1 at 01c20000 { #clock-cells = <0>; - compatible = "allwinner,sunxi-pll1-clk"; + compatible = "allwinner,sun4i-pll1-clk"; reg = <0x01c20000 0x4>; clocks = <&osc24M>; }; cpu: cpu at 01c20054 { #clock-cells = <0>; - compatible = "allwinner,sunxi-cpu-clk"; + compatible = "allwinner,sun4i-cpu-clk"; reg = <0x01c20054 0x4>; clocks = <&osc32k>, <&osc24M>, <&pll1>; };drivers/clk/sunxi/clk-sunxi.c +8
-8@@ -305,29 +305,29 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,/* Matches for of_clk_init */ static const __initconst struct of_device_id clk_match[] = { {.compatible ="fixed-clock" , .data = of_fixed_clk_setup,}, - {.compatible ="allwinner,sunxi-osc-clk" , .data = sunxi_osc_clk_setup,}, + {.compatible ="allwinner,sun4i-osc-clk" , .data = sunxi_osc_clk_setup,}, {} };/* Matches for factors clocks */ static const __initconst struct of_device_id clk_factors_match[] = { - {.compatible ="allwinner,sunxi-pll1-clk" , .data = &pll1_data,}, - {.compatible ="allwinner,sunxi-apb1-clk" , .data = &apb1_data,}, + {.compatible ="allwinner,sun4i-pll1-clk" , .data = &pll1_data,}, + {.compatible ="allwinner,sun4i-apb1-clk" , .data = &apb1_data,}, {} };/* Matches for divider clocks */ static const __initconst struct of_device_id clk_div_match[] = { - {.compatible ="allwinner,sunxi-axi-clk" , .data = &axi_data,}, - {.compatible ="allwinner,sunxi-ahb-clk" , .data = &ahb_data,}, - {.compatible ="allwinner,sunxi-apb0-clk" , .data = &apb0_data,}, + {.compatible ="allwinner,sun4i-axi-clk" , .data = &axi_data,}, + {.compatible ="allwinner,sun4i-ahb-clk" , .data = &ahb_data,}, + {.compatible ="allwinner,sun4i-apb0-clk" , .data = &apb0_data,}, {} };/* Matches for mux clocks */ static const __initconst struct of_device_id clk_mux_match[] = { - {.compatible ="allwinner,sunxi-cpu-clk" , .data = &cpu_data,}, - {.compatible ="allwinner,sunxi-apb1-mux-clk" , .data = &apb1_mux_data,}, + {.compatible ="allwinner,sun4i-cpu-clk" , .data = &cpu_data,}, + {.compatible ="allwinner,sun4i-apb1-mux-clk" , .data = &apb1_mux_data,}, {} };Signature · 1 line
1.8.2
Emilio López
maintainerPATCH 1/2 clk: sunxi: rename compatible strings
Hi Mike,
El 27/03/13 05:40, Mike Turquette escribi?:
Quoted 11 lines
Quoting Emilio L?pez (2013-03-26 19:39:17)
Quoted 10 lines
During the introduction of the Allwinner SoC platforms, sunxi was initially meant as a generic name for all the variants of the Allwinner SoC.
It was ok at the time of the support of only the A10 and A13 that look pretty much the same; but it's beginning to be troublesome with the future addition of the Allwinner A31 (sun6i) that is quite different, and would introduce some weird logic, where sunxi would actually mean in some case sun4i and sun5i but without sun6i...
Quoted 7 lines
Quoted 5 lines
Moreover, it makes the compatible strings naming scheme not consistent with other architectures, where usually for this kind of compability, we just use the oldest SoC name that has this IP, so let's do just this.
Signed-off-by Emilio L?pez <[email protected]>Which tree did you want this patch to go through?
This one should go through your tree, as you have the rest of the driver on it.
Thanks,
Emilio
Quoted 117 lines
Regards,
MikeQuoted 107 lines
---
These compatible strings have never been on a released kernel, so changing them now shouldn't cause any issues. Also see Maxime's "ARM: sunxi: Architecture cleanups and rework" which does the same for the rest of sunxi code.
Documentation/devicetree/bindings/clock/sunxi.txt | 22 +++++++++++----------- drivers/clk/sunxi/clk-sunxi.c | 16 ++++++++-------- 2 files changed, 19 insertions(+), 19 deletions(-)Documentation/devicetree/bindings/clock/sunxi.txt +11
-11@@ -6,14 +6,14 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be one of the following: - "allwinner,sunxi-osc-clk" - for a gatable oscillator - "allwinner,sunxi-pll1-clk" - for the main PLL clock - "allwinner,sunxi-cpu-clk" - for the CPU multiplexer clock - "allwinner,sunxi-axi-clk" - for the sunxi AXI clock - "allwinner,sunxi-ahb-clk" - for the sunxi AHB clock - "allwinner,sunxi-apb0-clk" - for the sunxi APB0 clock - "allwinner,sunxi-apb1-clk" - for the sunxi APB1 clock - "allwinner,sunxi-apb1-mux-clk" - for the sunxi APB1 clock muxing + "allwinner,sun4i-osc-clk" - for a gatable oscillator + "allwinner,sun4i-pll1-clk" - for the main PLL clock + "allwinner,sun4i-cpu-clk" - for the CPU multiplexer clock + "allwinner,sun4i-axi-clk" - for the AXI clock + "allwinner,sun4i-ahb-clk" - for the AHB clock + "allwinner,sun4i-apb0-clk" - for the APB0 clock + "allwinner,sun4i-apb1-clk" - for the APB1 clock + "allwinner,sun4i-apb1-mux-clk" - for the APB1 clock muxing Required properties for all clocks: - reg : shall be the control register address for the clock.@@ -24,21 +24,21 @@ For example: osc24M: osc24M at 01c20050 { #clock-cells = <0>; - compatible = "allwinner,sunxi-osc-clk"; + compatible = "allwinner,sun4i-osc-clk"; reg = <0x01c20050 0x4>; clocks = <&osc24M_fixed>; }; pll1: pll1 at 01c20000 { #clock-cells = <0>; - compatible = "allwinner,sunxi-pll1-clk"; + compatible = "allwinner,sun4i-pll1-clk"; reg = <0x01c20000 0x4>; clocks = <&osc24M>; }; cpu: cpu at 01c20054 { #clock-cells = <0>; - compatible = "allwinner,sunxi-cpu-clk"; + compatible = "allwinner,sun4i-cpu-clk"; reg = <0x01c20054 0x4>; clocks = <&osc32k>, <&osc24M>, <&pll1>; };drivers/clk/sunxi/clk-sunxi.c +8
-8@@ -305,29 +305,29 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,/* Matches for of_clk_init */ static const __initconst struct of_device_id clk_match[] = { {.compatible ="fixed-clock" , .data = of_fixed_clk_setup,}, - {.compatible ="allwinner,sunxi-osc-clk" , .data = sunxi_osc_clk_setup,}, + {.compatible ="allwinner,sun4i-osc-clk" , .data = sunxi_osc_clk_setup,}, {} };/* Matches for factors clocks */ static const __initconst struct of_device_id clk_factors_match[] = { - {.compatible ="allwinner,sunxi-pll1-clk" , .data = &pll1_data,}, - {.compatible ="allwinner,sunxi-apb1-clk" , .data = &apb1_data,}, + {.compatible ="allwinner,sun4i-pll1-clk" , .data = &pll1_data,}, + {.compatible ="allwinner,sun4i-apb1-clk" , .data = &apb1_data,}, {} };/* Matches for divider clocks */ static const __initconst struct of_device_id clk_div_match[] = { - {.compatible ="allwinner,sunxi-axi-clk" , .data = &axi_data,}, - {.compatible ="allwinner,sunxi-ahb-clk" , .data = &ahb_data,}, - {.compatible ="allwinner,sunxi-apb0-clk" , .data = &apb0_data,}, + {.compatible ="allwinner,sun4i-axi-clk" , .data = &axi_data,}, + {.compatible ="allwinner,sun4i-ahb-clk" , .data = &ahb_data,}, + {.compatible ="allwinner,sun4i-apb0-clk" , .data = &apb0_data,}, {} };/* Matches for mux clocks */ static const __initconst struct of_device_id clk_mux_match[] = { - {.compatible ="allwinner,sunxi-cpu-clk" , .data = &cpu_data,}, - {.compatible ="allwinner,sunxi-apb1-mux-clk" , .data = &apb1_mux_data,}, + {.compatible ="allwinner,sun4i-cpu-clk" , .data = &cpu_data,}, + {.compatible ="allwinner,sun4i-apb1-mux-clk" , .data = &apb1_mux_data,}, {} };Signature · 1 line
1.8.2_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH 1/2 clk: sunxi: rename compatible strings
Quoting Emilio L?pez (2013-03-27 02:30:21)
Quoted 18 lines
Hi Mike,
El 27/03/13 05:40, Mike Turquette escribi?:
Quoted 15 lines
Quoting Emilio L?pez (2013-03-26 19:39:17)
Quoted 14 lines
During the introduction of the Allwinner SoC platforms, sunxi was initially meant as a generic name for all the variants of the Allwinner SoC.
It was ok at the time of the support of only the A10 and A13 that look pretty much the same; but it's beginning to be troublesome with the future addition of the Allwinner A31 (sun6i) that is quite different, and would introduce some weird logic, where sunxi would actually mean in some case sun4i and sun5i but without sun6i...
Moreover, it makes the compatible strings naming scheme not consistent with other architectures, where usually for this kind of compability, we just use the oldest SoC name that has this IP, so let's do just this.
Quoted 7 lines
Quoted 3 lines
Quoted 1 line
Signed-off-by Emilio L?pez <[email protected]>Which tree did you want this patch to go through?
This one should go through your tree, as you have the rest of the driver on it.
Taken into clk-next.
Regards,
Mike
Quoted 121 lines
Thanks,
Emilio
Quoted 117 lines
Regards,
MikeQuoted 107 lines
---
These compatible strings have never been on a released kernel, so changing them now shouldn't cause any issues. Also see Maxime's "ARM: sunxi: Architecture cleanups and rework" which does the same for the rest of sunxi code.
Documentation/devicetree/bindings/clock/sunxi.txt | 22 +++++++++++----------- drivers/clk/sunxi/clk-sunxi.c | 16 ++++++++-------- 2 files changed, 19 insertions(+), 19 deletions(-)Documentation/devicetree/bindings/clock/sunxi.txt +11
-11@@ -6,14 +6,14 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be one of the following: - "allwinner,sunxi-osc-clk" - for a gatable oscillator - "allwinner,sunxi-pll1-clk" - for the main PLL clock - "allwinner,sunxi-cpu-clk" - for the CPU multiplexer clock - "allwinner,sunxi-axi-clk" - for the sunxi AXI clock - "allwinner,sunxi-ahb-clk" - for the sunxi AHB clock - "allwinner,sunxi-apb0-clk" - for the sunxi APB0 clock - "allwinner,sunxi-apb1-clk" - for the sunxi APB1 clock - "allwinner,sunxi-apb1-mux-clk" - for the sunxi APB1 clock muxing + "allwinner,sun4i-osc-clk" - for a gatable oscillator + "allwinner,sun4i-pll1-clk" - for the main PLL clock + "allwinner,sun4i-cpu-clk" - for the CPU multiplexer clock + "allwinner,sun4i-axi-clk" - for the AXI clock + "allwinner,sun4i-ahb-clk" - for the AHB clock + "allwinner,sun4i-apb0-clk" - for the APB0 clock + "allwinner,sun4i-apb1-clk" - for the APB1 clock + "allwinner,sun4i-apb1-mux-clk" - for the APB1 clock muxing Required properties for all clocks: - reg : shall be the control register address for the clock.@@ -24,21 +24,21 @@ For example: osc24M: osc24M at 01c20050 { #clock-cells = <0>; - compatible = "allwinner,sunxi-osc-clk"; + compatible = "allwinner,sun4i-osc-clk"; reg = <0x01c20050 0x4>; clocks = <&osc24M_fixed>; }; pll1: pll1 at 01c20000 { #clock-cells = <0>; - compatible = "allwinner,sunxi-pll1-clk"; + compatible = "allwinner,sun4i-pll1-clk"; reg = <0x01c20000 0x4>; clocks = <&osc24M>; }; cpu: cpu at 01c20054 { #clock-cells = <0>; - compatible = "allwinner,sunxi-cpu-clk"; + compatible = "allwinner,sun4i-cpu-clk"; reg = <0x01c20054 0x4>; clocks = <&osc32k>, <&osc24M>, <&pll1>; };drivers/clk/sunxi/clk-sunxi.c +8
-8@@ -305,29 +305,29 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,/* Matches for of_clk_init */ static const __initconst struct of_device_id clk_match[] = { {.compatible ="fixed-clock" , .data = of_fixed_clk_setup,}, - {.compatible ="allwinner,sunxi-osc-clk" , .data = sunxi_osc_clk_setup,}, + {.compatible ="allwinner,sun4i-osc-clk" , .data = sunxi_osc_clk_setup,}, {} };/* Matches for factors clocks */ static const __initconst struct of_device_id clk_factors_match[] = { - {.compatible ="allwinner,sunxi-pll1-clk" , .data = &pll1_data,}, - {.compatible ="allwinner,sunxi-apb1-clk" , .data = &apb1_data,}, + {.compatible ="allwinner,sun4i-pll1-clk" , .data = &pll1_data,}, + {.compatible ="allwinner,sun4i-apb1-clk" , .data = &apb1_data,}, {} };/* Matches for divider clocks */ static const __initconst struct of_device_id clk_div_match[] = { - {.compatible ="allwinner,sunxi-axi-clk" , .data = &axi_data,}, - {.compatible ="allwinner,sunxi-ahb-clk" , .data = &ahb_data,}, - {.compatible ="allwinner,sunxi-apb0-clk" , .data = &apb0_data,}, + {.compatible ="allwinner,sun4i-axi-clk" , .data = &axi_data,}, + {.compatible ="allwinner,sun4i-ahb-clk" , .data = &ahb_data,}, + {.compatible ="allwinner,sun4i-apb0-clk" , .data = &apb0_data,}, {} };/* Matches for mux clocks */ static const __initconst struct of_device_id clk_mux_match[] = { - {.compatible ="allwinner,sunxi-cpu-clk" , .data = &cpu_data,}, - {.compatible ="allwinner,sunxi-apb1-mux-clk" , .data = &apb1_mux_data,}, + {.compatible ="allwinner,sun4i-cpu-clk" , .data = &cpu_data,}, + {.compatible ="allwinner,sun4i-apb1-mux-clk" , .data = &apb1_mux_data,}, {} };Signature · 1 line
1.8.2_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Emilio López
maintainerPATCH 2/2 arm: sunxi: rename clock compatible strings
In reply to Emilio LópezDuring the introduction of the Allwinner SoC platforms, sunxi was initially meant as a generic name for all the variants of the Allwinner SoC.
It was ok at the time of the support of only the A10 and A13 that look pretty much the same; but it's beginning to be troublesome with the future addition of the Allwinner A31 (sun6i) that is quite different, and would introduce some weird logic, where sunxi would actually mean in some case sun4i and sun5i but without sun6i...
Moreover, it makes the compatible strings naming scheme not consistent with other architectures, where usually for this kind of compability, we just use the oldest SoC name that has this IP, so let's do just this.
---
These compatible strings have never been on a released kernel, so changing them now shouldn't cause any issues. Also see Maxime's "ARM: sunxi: Architecture cleanups and rework" which does the same for the rest of sunxi code.
arch/arm/boot/dts/sunxi.dtsi | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-)
arch/arm/boot/dts/sunxi.dtsi +8 -8
@@ -47,7 +47,7 @@ osc24M: osc24M at 01c20050 { #clock-cells = <0>; - compatible = "allwinner,sunxi-osc-clk"; + compatible = "allwinner,sun4i-osc-clk"; reg = <0x01c20050 0x4>; clocks = <&osc24M_fixed>; };
@@ -60,7 +60,7 @@ pll1: pll1 at 01c20000 { #clock-cells = <0>; - compatible = "allwinner,sunxi-pll1-clk"; + compatible = "allwinner,sun4i-pll1-clk"; reg = <0x01c20000 0x4>; clocks = <&osc24M>; };
@@ -68,28 +68,28 @@ /* dummy is 200M */ cpu: cpu at 01c20054 { #clock-cells = <0>; - compatible = "allwinner,sunxi-cpu-clk"; + compatible = "allwinner,sun4i-cpu-clk"; reg = <0x01c20054 0x4>; clocks = <&osc32k>, <&osc24M>, <&pll1>, <&dummy>; }; axi: axi at 01c20054 { #clock-cells = <0>; - compatible = "allwinner,sunxi-axi-clk"; + compatible = "allwinner,sun4i-axi-clk"; reg = <0x01c20054 0x4>; clocks = <&cpu>; }; ahb: ahb at 01c20054 { #clock-cells = <0>; - compatible = "allwinner,sunxi-ahb-clk"; + compatible = "allwinner,sun4i-ahb-clk"; reg = <0x01c20054 0x4>; clocks = <&axi>; }; apb0: apb0 at 01c20054 { #clock-cells = <0>; - compatible = "allwinner,sunxi-apb0-clk"; + compatible = "allwinner,sun4i-apb0-clk"; reg = <0x01c20054 0x4>; clocks = <&ahb>; };
@@ -97,14 +97,14 @@ /* dummy is pll62 */ apb1_mux: apb1_mux at 01c20058 { #clock-cells = <0>; - compatible = "allwinner,sunxi-apb1-mux-clk"; + compatible = "allwinner,sun4i-apb1-mux-clk"; reg = <0x01c20058 0x4>; clocks = <&osc24M>, <&dummy>, <&osc32k>; }; apb1: apb1 at 01c20058 { #clock-cells = <0>; - compatible = "allwinner,sunxi-apb1-clk"; + compatible = "allwinner,sun4i-apb1-clk"; reg = <0x01c20058 0x4>; clocks = <&apb1_mux>; };
Signature · 1 line
1.8.2
Maxime Ripard
AppliedPATCH 2/2 arm: sunxi: rename clock compatible strings
Le 27/03/2013 03:39, Emilio L?pez a ?crit :
Quoted 10 lines
During the introduction of the Allwinner SoC platforms, sunxi was initially meant as a generic name for all the variants of the Allwinner SoC.
It was ok at the time of the support of only the A10 and A13 that look pretty much the same; but it's beginning to be troublesome with the future addition of the Allwinner A31 (sun6i) that is quite different, and would introduce some weird logic, where sunxi would actually mean in some case sun4i and sun5i but without sun6i...
Quoted 5 lines
Moreover, it makes the compatible strings naming scheme not consistent with other architectures, where usually for this kind of compability, we just use the oldest SoC name that has this IP, so let's do just this.
Signed-off-by Emilio L?pez <[email protected]>
Applied,
Thanks!
Signature · 3 lines
Maxime Ripard, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com