Skip to contentSkip to conversation

ARM: shmobile: DT irqpin for r8a7779 and marzen-reference

PATCH Superseded Guennadi Liakhovetski 2 participants 10 messages Apr 3, 2013 – Apr 10, 2013

Subsystems (3)

v1 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

cover ARM: shmobile: DT irqpin for r8a7779 and marzen-reference

Hi

This 2 patches add DT irqpin support on marzen-reference. Only compile-tested due to the lack of hardware. The patches can go independently via their respective trees. irqpin on marzen will not work if patch 2 is applied before patch 1, but as long as there are no devices, using irqpin interrupts, no breakage will be caused.

Guennadi Liakhovetski (2):
irqchip: renesas-intc-irqpin: DT binding for sense bitfield width
ARM: shmobile: marzen-reference: add irqpin support in DT

Thanks
Guennadi
---
Guennadi Liakhovetski, Ph.D.
Freelance Open-Source Software Developer
http://www.open-technology.de/

#1 lore raw

PATCH 1/2 irqchip: renesas-intc-irqpin: DT binding for sense bitfield width

Most Renesas irqpin controllers have 4-bit sense fields, however, some have different widths. This patch adds a DT binding to optionally specify such non-standard values.

---
 .../interrupt-controller/renesas,intc-irqpin.txt   |    2 ++
 drivers/irqchip/irq-renesas-intc-irqpin.c          |    5 ++++-
 2 files changed, 6 insertions(+), 1 deletions(-)
Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt +2 -0
index e55d183..6b48742 100644
@@ -11,3 +11,5 @@ Optional properties:
   resource allocation properties
 - control-parent: disable and enable interrupts on the parent interrupt
   controller, needed for some broken implementations
+- sense-bitfield-width: width of a single sense bitfield in the SENSE register,
+  if different from the default 4 bits
drivers/irqchip/irq-renesas-intc-irqpin.c +4 -1
index 82bbe8f..6aadfe6 100644
@@ -381,9 +381,12 @@ static int intc_irqpin_probe(struct platform_device *pdev)
 	for (k = 0; k < p->number_of_irqs; k++)
 		intc_irqpin_mask_unmask_prio(p, k, 1);
 
-	if (!pdata)
+	if (!pdata) {
 		p->config.control_parent = of_property_read_bool(pdev->dev.of_node,
 								 "control-parent");
+		of_property_read_u32(pdev->dev.of_node, "sense-bitfield-width",
+				     &p->config.sense_bitfield_width);
+	}
 
 	/* use more severe masking method if requested */
 	if (p->config.control_parent) {
Signature · 1 line
1.7.2.5
#2 lore raw

PATCH 2/2 ARM: shmobile: marzen-reference: add irqpin support in DT

In reply to Guennadi Liakhovetski

Add an irqpin interrupt controller DT node on marzen-reference.

---
 arch/arm/boot/dts/r8a7779.dtsi |   17 +++++++++++++++++
 1 files changed, 17 insertions(+), 0 deletions(-)
arch/arm/boot/dts/r8a7779.dtsi +17 -0
index fe5c6f2..7f146c6 100644
@@ -48,6 +48,23 @@
                       <0xf0000100 0x100>;
         };
 
+	irqpin0: irqpin at fe780010 {
+		compatible = "renesas,intc-irqpin";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		reg = <0xfe78001c 4>,
+			<0xfe780010 4>,
+			<0xfe780024 4>,
+			<0xfe780044 4>,
+			<0xfe780064 4>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 27 0x4
+				0 28 0x4
+				0 29 0x4
+				0 30 0x4>;
+		sense-bitfield-width = <2>;
+	};
+
 	i2c0: i2c at 0xffc70000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
Signature · 1 line
1.7.2.5
#3 lore raw

PATCH 2/2 ARM: shmobile: marzen-reference: add irqpin support in DT

Quoted 3 lines · Guennadi Liakhovetski

Add an irqpin interrupt controller DT node on marzen-reference.

Thanks, queued up in the boards-marzen branch.

#4 lore raw

cover ARM: shmobile: DT irqpin for r8a7779 and marzen-reference

In reply to Guennadi Liakhovetski
Quoted 7 lines · Guennadi Liakhovetski

Hi

This 2 patches add DT irqpin support on marzen-reference. Only compile-tested due to the lack of hardware. The patches can go independently via their respective trees. irqpin on marzen will not work if patch 2 is applied before patch 1, but as long as there are no devices, using irqpin interrupts, no breakage will be caused.

I have applied both patches and the dependency I mention below. I have also applied the small patch, inlined below, to hook-up the LAN controller. Unfortunately it doesn't seem to be receiving any interrupts. Perhaps I am missing something?

Quoted 3 lines

Guennadi Liakhovetski (2):
irqchip: renesas-intc-irqpin: DT binding for sense bitfield width

The above patch depends on "[1/3] ARM: shmobile: irqpin: fix handling of spurious interrupts in DT case", right? Has there been any progress in your discussions with Magnus about what to do about that patch?

Quoted 1 line

ARM: shmobile: marzen-reference: add irqpin support in DT

LAN patch:

arch/arm/boot/dts/r8a7779-marzen-reference.dts +2 -2
index 72be4c8..3d98833 100644
@@ -38,8 +38,8 @@
 		compatible = "smsc,lan9220", "smsc,lan9115";
 		reg = <0x18000000 0x100>;
 		phy-mode = "mii";
-		interrupt-parent = <&gic>;
-		interrupts = <0 28 0x4>;
+		interrupt-parent = <&irqpin0>;
+		interrupts = <28 0>;
 		reg-io-width = <4>;
 		vddvario-supply = <&fixedregulator3v3>;
 		vdd33a-supply = <&fixedregulator3v3>;

Boot log and /proc/interrupts with LAN patch (version without LAN patch is below):

Booting Linux on physical CPU 0x0
Linux version 3.9.0-rc2-00003-gd779a6cb-dirty (horms at ayumi.isobedori.kobe.vergenet.net) (gcc version 4.5.2 (Sourcery G++ Lite 2011.03-41) ) #1433 SMP Thu Apr 4 12:43:06 JST 2013
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: marzen, model: marzen
debug: ignoring loglevel setting.
Memory policy: ECC disabled, Data cache writealloc
On node 0 totalpages: 262144
free_area_init_node: node 0, pgdat c03cdb00, node_mem_map c055a000
Normal zone: 1520 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 194560 pages, LIFO batch:31
HighMem zone: 528 pages used for memmap
HighMem zone: 67584 pages, LIFO batch:15
PERCPU: Embedded 5 pages/cpu @c0d62000 s6848 r0 d13632 u32768
pcpu-alloc: s6848 r0 d13632 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260624
Kernel command line: console=ttySC2,115200 earlyprintk=sh-sci.2,115200 ignore_loglevel root=/dev/nfs ip=on
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
__ex_table already sorted, skipping sort
Memory: 1024MB = 1024MB total
Memory: 1035404k/1035404k available, 13172k reserved, 270336K highmem
Virtual kernel memory layout:

    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
    lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
      .text : 0xc0008000 - 0xc0380d20   (3556 kB)
      .init : 0xc0381000 - 0xc03a8ac0   ( 159 kB)
      .data : 0xc03aa000 - 0xc03ce6c0   ( 146 kB)
       .bss : 0xc03ce6c0 - 0xc03f9134   ( 171 kB)

Hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
sched_clock: 32 bits at 1kHz, resolution 976562ns, wraps every 4194303999ms Calibrating delay loop (skipped) preset value.. 1000.00 BogoMIPS (lpj=488000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0xc02dc328 - 0xc02dc380
CPU1: Booted secondary processor
CPU2: Booted secondary processor
CPU3: Booted secondary processor
Brought up 4 CPUs
SMP: Total of 4 processors activated (4000.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations sh-pfc pfc-r8a7779: r8a7779_pfc support registered renesas_intc_irqpin fe78001c.irqpin: driving 4 irqs

------------[ cut here ]------------
WARNING: at kernel/irq/irqdomain.c:766 irq_linear_revmap+0x3c/0x44()
[<c000edc0>] (unwind_backtrace+0x0/0xf8) from [<c0017628>] (warn_slowpath_common+0x50/0x64)
[<c0017628>] (warn_slowpath_common+0x50/0x64) from [<c00176f0>] (warn_slowpath_null+0x1c/0x24)
[<c00176f0>] (warn_slowpath_null+0x1c/0x24) from [<c006356c>] (irq_linear_revmap+0x3c/0x44)
[<c006356c>] (irq_linear_revmap+0x3c/0x44) from [<c0063658>] (irq_create_mapping+0x20/0x118)
[<c0063658>] (irq_create_mapping+0x20/0x118) from [<c00637cc>] (irq_create_of_mapping+0x7c/0x100)
[<c00637cc>] (irq_create_of_mapping+0x7c/0x100) from [<c0224c00>] (irq_of_parse_and_map+0x30/0x38)
[<c0224c00>] (irq_of_parse_and_map+0x30/0x38) from [<c0224c20>] (of_irq_to_resource+0x18/0x74)
[<c0224c20>] (of_irq_to_resource+0x18/0x74) from [<c0224ca0>] (of_irq_count+0x24/0x34)
[<c0224ca0>] (of_irq_count+0x24/0x34) from [<c0225508>] (of_device_alloc+0x1b8/0x248)
[<c0225508>] (of_device_alloc+0x1b8/0x248) from [<c02255d4>] (of_platform_device_create_pdata+0x3c/0x80)
[<c02255d4>] (of_platform_device_create_pdata+0x3c/0x80) from [<c02256ec>] (of_platform_bus_create+0xd4/0x178)
[<c02256ec>] (of_platform_bus_create+0xd4/0x178) from [<c02258cc>] (of_platform_populate+0x60/0x98)
[<c02258cc>] (of_platform_populate+0x60/0x98) from [<c0382854>] (customize_machine+0x20/0x28)
[<c0382854>] (customize_machine+0x20/0x28) from [<c0381834>] (do_one_initcall+0xa0/0x16c)
[<c0381834>] (do_one_initcall+0xa0/0x16c) from [<c0381a2c>] (kernel_init_freeable+0x12c/0x1d0)
[<c0381a2c>] (kernel_init_freeable+0x12c/0x1d0) from [<c02cfd6c>] (kernel_init+0x8/0xe8)
[<c02cfd6c>] (kernel_init+0x8/0xe8) from [<c0009e18>] (ret_from_fork+0x14/0x3c)
---[ end trace a30592ddc9049899 ]---
------------[ cut here ]------------
WARNING: at kernel/irq/irqdomain.c:766 irq_linear_revmap+0x3c/0x44()
[<c000edc0>] (unwind_backtrace+0x0/0xf8) from [<c0017628>] (warn_slowpath_common+0x50/0x64)
[<c0017628>] (warn_slowpath_common+0x50/0x64) from [<c00176f0>] (warn_slowpath_null+0x1c/0x24)
[<c00176f0>] (warn_slowpath_null+0x1c/0x24) from [<c006356c>] (irq_linear_revmap+0x3c/0x44)
[<c006356c>] (irq_linear_revmap+0x3c/0x44) from [<c0063658>] (irq_create_mapping+0x20/0x118)
[<c0063658>] (irq_create_mapping+0x20/0x118) from [<c00637cc>] (irq_create_of_mapping+0x7c/0x100)
[<c00637cc>] (irq_create_of_mapping+0x7c/0x100) from [<c0224c00>] (irq_of_parse_and_map+0x30/0x38)
[<c0224c00>] (irq_of_parse_and_map+0x30/0x38) from [<c0224c20>] (of_irq_to_resource+0x18/0x74)
[<c0224c20>] (of_irq_to_resource+0x18/0x74) from [<c0224d28>] (of_irq_to_resource_table+0x78/0x94)
[<c0224d28>] (of_irq_to_resource_table+0x78/0x94) from [<c02254a4>] (of_device_alloc+0x154/0x248)
[<c02254a4>] (of_device_alloc+0x154/0x248) from [<c02255d4>] (of_platform_device_create_pdata+0x3c/0x80)
[<c02255d4>] (of_platform_device_create_pdata+0x3c/0x80) from [<c02256ec>] (of_platform_bus_create+0xd4/0x178)
[<c02256ec>] (of_platform_bus_create+0xd4/0x178) from [<c02258cc>] (of_platform_populate+0x60/0x98)
[<c02258cc>] (of_platform_populate+0x60/0x98) from [<c0382854>] (customize_machine+0x20/0x28)
[<c0382854>] (customize_machine+0x20/0x28) from [<c0381834>] (do_one_initcall+0xa0/0x16c)
[<c0381834>] (do_one_initcall+0xa0/0x16c) from [<c0381a2c>] (kernel_init_freeable+0x12c/0x1d0)
[<c0381a2c>] (kernel_init_freeable+0x12c/0x1d0) from [<c02cfd6c>] (kernel_init+0x8/0xe8)
[<c02cfd6c>] (kernel_init+0x8/0xe8) from [<c0009e18>] (ret_from_fork+0x14/0x3c)
---[ end trace a30592ddc904989a ]---

No ATAGs?
[<c0229260>] (of_platform_device_create_pdata+0x3c/0x80) from [<c0229378>] (of_platform_bus_create+0xd4/0x178) [<c0229378>] (of_platform_bus_create+0xd4/0x178) from [<c0229558>] (of_platform_populate+0x60/0x98) [<c0229558>] (of_platform_populate+0x60/0x98) from [<c0387714>] (customize_machine+0x20/0x28) [<c0387714>] (customize_machine+0x20/0x28) from [<c0385888>] (do_one_initcall+0xa0/0x16c) [<c0385888>] (do_one_initcall+0xa0/0x16c) from [<c0385a80>] (kernel_init_freeable+0x12c/0x1d0) [<c0385a80>] (kernel_init_freeable+0x12c/0x1d0) from [<c02d39f8>] (kernel_init+0x8/0xe8) [<c02d39f8>] (kernel_init+0x8/0xe8) from [<c0009e98>] (ret_from_fork+0x14/0x3c)

---[ end trace a30592ddc9049899 ]---
------------[ cut here ]------------
WARNING: at kernel/irq/irqdomain.c:766 irq_linear_revmap+0x3c/0x44()
[<c000ee40>] (unwind_backtrace+0x0/0xf8) from [<c0017888>] (warn_slowpath_common+0x50/0x64)
[<c0017888>] (warn_slowpath_common+0x50/0x64) from [<c0017950>] (warn_slowpath_null+0x1c/0x24)
[<c0017950>] (warn_slowpath_null+0x1c/0x24) from [<c00637cc>] (irq_linear_revmap+0x3c/0x44)
[<c00637cc>] (irq_linear_revmap+0x3c/0x44) from [<c00638b8>] (irq_create_mapping+0x20/0x118)
[<c00638b8>] (irq_create_mapping+0x20/0x118) from [<c0063a2c>] (irq_create_of_mapping+0x7c/0x100)
[<c0063a2c>] (irq_create_of_mapping+0x7c/0x100) from [<c022888c>] (irq_of_parse_and_map+0x30/0x38)
[<c022888c>] (irq_of_parse_and_map+0x30/0x38) from [<c02288ac>] (of_irq_to_resource+0x18/0x74)
[<c02288ac>] (of_irq_to_resource+0x18/0x74) from [<c02289b4>] (of_irq_to_resource_table+0x78/0x94)
[<c02289b4>] (of_irq_to_resource_table+0x78/0x94) from [<c0229130>] (of_device_alloc+0x154/0x248)
[<c0229130>] (of_device_alloc+0x154/0x248) from [<c0229260>] (of_platform_device_create_pdata+0x3c/0x80)
[<c0229260>] (of_platform_device_create_pdata+0x3c/0x80) from [<c0229378>] (of_platform_bus_create+0xd4/0x178)
[<c0229378>] (of_platform_bus_create+0xd4/0x178) from [<c0229558>] (of_platform_populate+0x60/0x98)
[<c0229558>] (of_platform_populate+0x60/0x98) from [<c0387714>] (customize_machine+0x20/0x28)
[<c0387714>] (customize_machine+0x20/0x28) from [<c0385888>] (do_one_initcall+0xa0/0x16c)
[<c0385888>] (do_one_initcall+0xa0/0x16c) from [<c0385a80>] (kernel_init_freeable+0x12c/0x1d0)
[<c0385a80>] (kernel_init_freeable+0x12c/0x1d0) from [<c02d39f8>] (kernel_init+0x8/0xe8)
[<c02d39f8>] (kernel_init+0x8/0xe8) from [<c0009e98>] (ret_from_fork+0x14/0x3c)
---[ end trace a30592ddc904989a ]---

No ATAGs?
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
sh_tmu sh_tmu.0: used for clock events
sh_tmu sh_tmu.0: used for periodic clock events
sh_tmu sh_tmu.1: used as clock source
Switching to clocksource sh_tmu.1
Clockevents: could not switch to one-shot mode:
Clockevents: could not switch to one-shot mode:
Clockevents: could not switch to one-shot mode:
dummy_timer is not functional.
dummy_timer is not functional.
Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
dummy_timer is not functional.
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
bounce pool size: 64 pages
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered (default)
gpio_rcar gpio_rcar.0: driving 32 GPIOs
gpio_rcar gpio_rcar.1: driving 32 GPIOs
gpio_rcar gpio_rcar.2: driving 32 GPIOs
gpio_rcar gpio_rcar.3: driving 32 GPIOs
gpio_rcar gpio_rcar.4: driving 32 GPIOs
gpio_rcar gpio_rcar.5: driving 32 GPIOs
gpio_rcar gpio_rcar.6: driving 9 GPIOs
SuperH SCI(F) driver initialized
sh-sci.0: ttySC0 at MMIO 0xffe40000 (irq = 120) is a scif
sh-sci.1: ttySC1 at MMIO 0xffe41000 (irq = 121) is a scif
sh-sci.2: ttySC2 at MMIO 0xffe42000 (irq = 122) is a scif
console [ttySC2] enabled
sh-sci.3: ttySC3 at MMIO 0xffe43000 (irq = 123) is a scif
sh-sci.4: ttySC4 at MMIO 0xffe44000 (irq = 124) is a scif
sh-sci.5: ttySC5 at MMIO 0xffe45000 (irq = 125) is a scif
scsi0 : sata_rcar
ata1: SATA max UDMA/133 irq 132
smsc911x: Driver version 2008-10-21
libphy: smsc911x-mdio: probed
smsc911x 18000000.lan0 eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=18000000.lan0-ff:01, irq=-1) smsc911x 18000000.lan0 eth0: MAC Address: 2e:09:0a:00:3c:de
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-platform: EHCI generic platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
rcar_thermal ffc48000.thermal: 1 sensor proved
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
ata1: link resume succeeded after 1 retries
ata1: SATA link down (SStatus 0 SControl 300)
smsc911x 18000000.lan0 eth0: ISR failed signaling test (IRQ 257)
IP-Config: Failed to open eth0
IP-Config: No network devices available

Freeing init memory: 2916K

boot (Linux 3.9.0-rc2-00003-gd779a6cb-dirty, BusyBox v1.16.0.git, kexec-tools 2.0.1-git) / #
/ # cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3

 59:          0          0          0          0       GIC  fe78001c.irqpin
 60:          0          0          0          0       GIC  fe78001c.irqpin
 61:          0          0          0          0       GIC  fe78001c.irqpin
 62:          0          0          0          0       GIC  fe78001c.irqpin
 64:       8493          0          0          0       GIC  sh_tmu.0
122:         48          0          0          0       GIC  sh-sci.2:mux
132:          0          0          0          0       GIC  sata_rcar
173:          0          0          0          0       GIC  gpio_rcar.0
174:          0          0          0          0       GIC  gpio_rcar.1
175:          0          0          0          0       GIC  gpio_rcar.2
176:          0          0          0          0       GIC  gpio_rcar.3
177:          0          0          0          0       GIC  gpio_rcar.4
178:          0          0          0          0       GIC  gpio_rcar.5
179:          0          0          0          0       GIC  gpio_rcar.6
257:          0          0          0          0  fe78001c.irqpin  eth0
IPI0:          0          0          0          0  CPU wakeup interrupts
IPI1:          0       7869       8493       8487  Timer broadcast interrupts
IPI2:        446        503         73         46  Rescheduling interrupts
IPI3:         21         37         54         56  Function call interrupts
IPI4:          0          0          0          0  Single function call interrupts
IPI5:          0          0          0          0  CPU stop interrupts
Err:          0

/ #

Boot log and /proc/interrupts with LAN patch (version without LAN patch is below):

Booting Linux on physical CPU 0x0
Linux version 3.9.0-rc2-00003-gd779a6cb (horms at ayumi.isobedori.kobe.vergenet.net) (gcc version 4.5.2 (Sourcery G++ Lite 2011.03-41) ) #1435 SMP Thu Apr 4 12:51:52 JST 2013
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: marzen, model: marzen
debug: ignoring loglevel setting.
Memory policy: ECC disabled, Data cache writealloc
On node 0 totalpages: 262144
free_area_init_node: node 0, pgdat c0683b00, node_mem_map c08fb000
Normal zone: 1520 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 194560 pages, LIFO batch:31
HighMem zone: 528 pages used for memmap
HighMem zone: 67584 pages, LIFO batch:15
PERCPU: Embedded 5 pages/cpu @c1103000 s6848 r0 d13632 u32768
pcpu-alloc: s6848 r0 d13632 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260624
Kernel command line: console=ttySC2,115200 earlyprintk=sh-sci.2,115200 ignore_loglevel root=/dev/nfs ip=on
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
__ex_table already sorted, skipping sort
Memory: 1024MB = 1024MB total
Memory: 1032628k/1032628k available, 15948k reserved, 270336K highmem
Virtual kernel memory layout:

    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
    lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
      .text : 0xc0008000 - 0xc0384e4c   (3572 kB)
      .init : 0xc0385000 - 0xc065eac0   (2919 kB)
      .data : 0xc0660000 - 0xc06846c0   ( 146 kB)
       .bss : 0xc06846c0 - 0xc06af174   ( 171 kB)

Hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
sched_clock: 32 bits at 1kHz, resolution 976562ns, wraps every 4194303999ms Calibrating delay loop (skipped) preset value.. 1000.00 BogoMIPS (lpj=488000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0xc02df328 - 0xc02df380
CPU1: Booted secondary processor
CPU2: Booted secondary processor
CPU3: Booted secondary processor
Brought up 4 CPUs
SMP: Total of 4 processors activated (4000.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations sh-pfc pfc-r8a7779: r8a7779_pfc support registered renesas_intc_irqpin fe78001c.irqpin: driving 4 irqs
No ATAGs?
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
sh_tmu sh_tmu.0: used for clock events
sh_tmu sh_tmu.0: used for periodic clock events
sh_tmu sh_tmu.1: used as clock source
Switching to clocksource sh_tmu.1
Clockevents: could not switch to one-shot mode:
Clockevents: could not switch to one-shot mode:
Clockevents: could not switch to one-shot mode:
dummy_timer is not functional.
dummy_timer is not functional.
Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
dummy_timer is not functional.
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
bounce pool size: 64 pages
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered
io scheduler deadline registered (default)
gpio_rcar gpio_rcar.0: driving 32 GPIOs
gpio_rcar gpio_rcar.1: driving 32 GPIOs
gpio_rcar gpio_rcar.2: driving 32 GPIOs
gpio_rcar gpio_rcar.3: driving 32 GPIOs
gpio_rcar gpio_rcar.4: driving 32 GPIOs
gpio_rcar gpio_rcar.5: driving 32 GPIOs
gpio_rcar gpio_rcar.6: driving 9 GPIOs
SuperH SCI(F) driver initialized
sh-sci.0: ttySC0 at MMIO 0xffe40000 (irq = 120) is a scif sh-sci.1: ttySC1 at MMIO 0xffe41000 (irq = 121) is a scif sh-sci.2: ttySC2 at MMIO 0xffe42000 (irq = 122) is a scif
console [ttySC2] enabled
sh-sci.3: ttySC3 at MMIO 0xffe43000 (irq = 123) is a scif sh-sci.4: ttySC4 at MMIO 0xffe44000 (irq = 124) is a scif sh-sci.5: ttySC5 at MMIO 0xffe45000 (irq = 125) is a scif
scsi0 : sata_rcar
ata1: SATA max UDMA/133 irq 132
smsc911x: Driver version 2008-10-21
genirq: Flags mismatch irq 60. 00000080 (eth%d) vs. 00000000 (fe78001c.irqpin)
smsc911x: probe of 18000000.lan0 failed with error -16
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-platform: EHCI generic platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
rcar_thermal ffc48000.thermal: 1 sensor proved
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
ata1: link resume succeeded after 1 retries
ata1: SATA link down (SStatus 0 SControl 300)
Freeing init memory: 2916K

boot (Linux 3.9.0-rc2-00003-gd779a6cb, BusyBox v1.16.0.git, kexec-tools 2.0.1-git) / # cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3

 59:          0          0          0          0       GIC  fe78001c.irqpin
 60:          0          0          0          0       GIC  fe78001c.irqpin
 61:          0          0          0          0       GIC  fe78001c.irqpin
 62:          0          0          0          0       GIC  fe78001c.irqpin
 64:      49198          0          0          0       GIC  sh_tmu.0
122:         45          0          0          0       GIC  sh-sci.2:mux
132:          0          0          0          0       GIC  sata_rcar
173:          0          0          0          0       GIC  gpio_rcar.0
174:          0          0          0          0       GIC  gpio_rcar.1
175:          0          0          0          0       GIC  gpio_rcar.2
176:          0          0          0          0       GIC  gpio_rcar.3
177:          0          0          0          0       GIC  gpio_rcar.4
178:          0          0          0          0       GIC  gpio_rcar.5
179:          0          0          0          0       GIC  gpio_rcar.6
IPI0:          0          0          0          0  CPU wakeup interrupts
IPI1:          0      49192      49198      48802  Timer broadcast interrupts
IPI2:        437        478         87         88  Rescheduling interrupts
IPI3:         56         37         36         39  Function call interrupts
IPI4:          0          0          0          0  Single function call interrupts
IPI5:          0          0          0          0  CPU stop interrupts

Err:

#5 lore raw

cover ARM: shmobile: DT irqpin for r8a7779 and marzen-reference

Hi Simon

Quoted 9 lines · Simon Horman
Quoted 7 lines · Guennadi Liakhovetski

Hi

This 2 patches add DT irqpin support on marzen-reference. Only compile-tested due to the lack of hardware. The patches can go independently via their respective trees. irqpin on marzen will not work if patch 2 is applied before patch 1, but as long as there are no devices, using irqpin interrupts, no breakage will be caused.

Quoted 4 lines

I have applied both patches and the dependency I mention below. I have also applied the small patch, inlined below, to hook-up the LAN controller. Unfortunately it doesn't seem to be receiving any interrupts. Perhaps I am missing something?

Are you sure 28 is the correct number in the irqpin IRQ space? Seems strange to me. Should be 1 perhaps (counting from 0), or 2 - not sure how that mapping would look like.

Quoted 5 lines
Quoted 2 lines

Guennadi Liakhovetski (2):
irqchip: renesas-intc-irqpin: DT binding for sense bitfield width

The above patch depends on "[1/3] ARM: shmobile: irqpin: fix handling of spurious interrupts in DT case", right?

Not functionally. Spurious interrupts occur on sh73a0, the sense bitfield is needed for r8a7779. But the latter won't apply without the former, that's right.

Quoted 2 lines

Has there been any progress in your
discussions with Magnus about what to do about that patch?

No, not yet.

Thanks
Guennadi

Quoted 398 lines
Quoted 1 line

ARM: shmobile: marzen-reference: add irqpin support in DT

LAN patch:

arch/arm/boot/dts/r8a7779-marzen-reference.dts +2 -2
index 72be4c8..3d98833 100644
@@ -38,8 +38,8 @@
 		compatible = "smsc,lan9220", "smsc,lan9115";
 		reg = <0x18000000 0x100>;
 		phy-mode = "mii";
-		interrupt-parent = <&gic>;
-		interrupts = <0 28 0x4>;
+		interrupt-parent = <&irqpin0>;
+		interrupts = <28 0>;
 		reg-io-width = <4>;
 		vddvario-supply = <&fixedregulator3v3>;
 		vdd33a-supply = <&fixedregulator3v3>;

Boot log and /proc/interrupts with LAN patch (version without LAN patch is below):

Booting Linux on physical CPU 0x0
Linux version 3.9.0-rc2-00003-gd779a6cb-dirty (horms at ayumi.isobedori.kobe.vergenet.net) (gcc version 4.5.2 (Sourcery G++ Lite 2011.03-41) ) #1433 SMP Thu Apr 4 12:43:06 JST 2013
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: marzen, model: marzen
debug: ignoring loglevel setting.
Memory policy: ECC disabled, Data cache writealloc
On node 0 totalpages: 262144
free_area_init_node: node 0, pgdat c03cdb00, node_mem_map c055a000
Normal zone: 1520 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 194560 pages, LIFO batch:31
HighMem zone: 528 pages used for memmap
HighMem zone: 67584 pages, LIFO batch:15
PERCPU: Embedded 5 pages/cpu @c0d62000 s6848 r0 d13632 u32768
pcpu-alloc: s6848 r0 d13632 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260624
Kernel command line: console=ttySC2,115200 earlyprintk=sh-sci.2,115200 ignore_loglevel root=/dev/nfs ip=on
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
__ex_table already sorted, skipping sort
Memory: 1024MB = 1024MB total
Memory: 1035404k/1035404k available, 13172k reserved, 270336K highmem
Virtual kernel memory layout:

    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
    lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
      .text : 0xc0008000 - 0xc0380d20   (3556 kB)
      .init : 0xc0381000 - 0xc03a8ac0   ( 159 kB)
      .data : 0xc03aa000 - 0xc03ce6c0   ( 146 kB)
       .bss : 0xc03ce6c0 - 0xc03f9134   ( 171 kB)

Hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
sched_clock: 32 bits at 1kHz, resolution 976562ns, wraps every 4194303999ms Calibrating delay loop (skipped) preset value.. 1000.00 BogoMIPS (lpj=488000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0xc02dc328 - 0xc02dc380
CPU1: Booted secondary processor
CPU2: Booted secondary processor
CPU3: Booted secondary processor
Brought up 4 CPUs
SMP: Total of 4 processors activated (4000.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations sh-pfc pfc-r8a7779: r8a7779_pfc support registered renesas_intc_irqpin fe78001c.irqpin: driving 4 irqs

------------[ cut here ]------------
WARNING: at kernel/irq/irqdomain.c:766 irq_linear_revmap+0x3c/0x44()
[<c000edc0>] (unwind_backtrace+0x0/0xf8) from [<c0017628>] (warn_slowpath_common+0x50/0x64)
[<c0017628>] (warn_slowpath_common+0x50/0x64) from [<c00176f0>] (warn_slowpath_null+0x1c/0x24)
[<c00176f0>] (warn_slowpath_null+0x1c/0x24) from [<c006356c>] (irq_linear_revmap+0x3c/0x44)
[<c006356c>] (irq_linear_revmap+0x3c/0x44) from [<c0063658>] (irq_create_mapping+0x20/0x118)
[<c0063658>] (irq_create_mapping+0x20/0x118) from [<c00637cc>] (irq_create_of_mapping+0x7c/0x100)
[<c00637cc>] (irq_create_of_mapping+0x7c/0x100) from [<c0224c00>] (irq_of_parse_and_map+0x30/0x38)
[<c0224c00>] (irq_of_parse_and_map+0x30/0x38) from [<c0224c20>] (of_irq_to_resource+0x18/0x74)
[<c0224c20>] (of_irq_to_resource+0x18/0x74) from [<c0224ca0>] (of_irq_count+0x24/0x34)
[<c0224ca0>] (of_irq_count+0x24/0x34) from [<c0225508>] (of_device_alloc+0x1b8/0x248)
[<c0225508>] (of_device_alloc+0x1b8/0x248) from [<c02255d4>] (of_platform_device_create_pdata+0x3c/0x80)
[<c02255d4>] (of_platform_device_create_pdata+0x3c/0x80) from [<c02256ec>] (of_platform_bus_create+0xd4/0x178)
[<c02256ec>] (of_platform_bus_create+0xd4/0x178) from [<c02258cc>] (of_platform_populate+0x60/0x98)
[<c02258cc>] (of_platform_populate+0x60/0x98) from [<c0382854>] (customize_machine+0x20/0x28)
[<c0382854>] (customize_machine+0x20/0x28) from [<c0381834>] (do_one_initcall+0xa0/0x16c)
[<c0381834>] (do_one_initcall+0xa0/0x16c) from [<c0381a2c>] (kernel_init_freeable+0x12c/0x1d0)
[<c0381a2c>] (kernel_init_freeable+0x12c/0x1d0) from [<c02cfd6c>] (kernel_init+0x8/0xe8)
[<c02cfd6c>] (kernel_init+0x8/0xe8) from [<c0009e18>] (ret_from_fork+0x14/0x3c)
---[ end trace a30592ddc9049899 ]---
------------[ cut here ]------------
WARNING: at kernel/irq/irqdomain.c:766 irq_linear_revmap+0x3c/0x44()
[<c000edc0>] (unwind_backtrace+0x0/0xf8) from [<c0017628>] (warn_slowpath_common+0x50/0x64)
[<c0017628>] (warn_slowpath_common+0x50/0x64) from [<c00176f0>] (warn_slowpath_null+0x1c/0x24)
[<c00176f0>] (warn_slowpath_null+0x1c/0x24) from [<c006356c>] (irq_linear_revmap+0x3c/0x44)
[<c006356c>] (irq_linear_revmap+0x3c/0x44) from [<c0063658>] (irq_create_mapping+0x20/0x118)
[<c0063658>] (irq_create_mapping+0x20/0x118) from [<c00637cc>] (irq_create_of_mapping+0x7c/0x100)
[<c00637cc>] (irq_create_of_mapping+0x7c/0x100) from [<c0224c00>] (irq_of_parse_and_map+0x30/0x38)
[<c0224c00>] (irq_of_parse_and_map+0x30/0x38) from [<c0224c20>] (of_irq_to_resource+0x18/0x74)
[<c0224c20>] (of_irq_to_resource+0x18/0x74) from [<c0224d28>] (of_irq_to_resource_table+0x78/0x94)
[<c0224d28>] (of_irq_to_resource_table+0x78/0x94) from [<c02254a4>] (of_device_alloc+0x154/0x248)
[<c02254a4>] (of_device_alloc+0x154/0x248) from [<c02255d4>] (of_platform_device_create_pdata+0x3c/0x80)
[<c02255d4>] (of_platform_device_create_pdata+0x3c/0x80) from [<c02256ec>] (of_platform_bus_create+0xd4/0x178)
[<c02256ec>] (of_platform_bus_create+0xd4/0x178) from [<c02258cc>] (of_platform_populate+0x60/0x98)
[<c02258cc>] (of_platform_populate+0x60/0x98) from [<c0382854>] (customize_machine+0x20/0x28)
[<c0382854>] (customize_machine+0x20/0x28) from [<c0381834>] (do_one_initcall+0xa0/0x16c)
[<c0381834>] (do_one_initcall+0xa0/0x16c) from [<c0381a2c>] (kernel_init_freeable+0x12c/0x1d0)
[<c0381a2c>] (kernel_init_freeable+0x12c/0x1d0) from [<c02cfd6c>] (kernel_init+0x8/0xe8)
[<c02cfd6c>] (kernel_init+0x8/0xe8) from [<c0009e18>] (ret_from_fork+0x14/0x3c)
---[ end trace a30592ddc904989a ]---

No ATAGs?
[<c0229260>] (of_platform_device_create_pdata+0x3c/0x80) from [<c0229378>] (of_platform_bus_create+0xd4/0x178) [<c0229378>] (of_platform_bus_create+0xd4/0x178) from [<c0229558>] (of_platform_populate+0x60/0x98) [<c0229558>] (of_platform_populate+0x60/0x98) from [<c0387714>] (customize_machine+0x20/0x28) [<c0387714>] (customize_machine+0x20/0x28) from [<c0385888>] (do_one_initcall+0xa0/0x16c) [<c0385888>] (do_one_initcall+0xa0/0x16c) from [<c0385a80>] (kernel_init_freeable+0x12c/0x1d0) [<c0385a80>] (kernel_init_freeable+0x12c/0x1d0) from [<c02d39f8>] (kernel_init+0x8/0xe8) [<c02d39f8>] (kernel_init+0x8/0xe8) from [<c0009e98>] (ret_from_fork+0x14/0x3c)

---[ end trace a30592ddc9049899 ]---
------------[ cut here ]------------
WARNING: at kernel/irq/irqdomain.c:766 irq_linear_revmap+0x3c/0x44()
[<c000ee40>] (unwind_backtrace+0x0/0xf8) from [<c0017888>] (warn_slowpath_common+0x50/0x64)
[<c0017888>] (warn_slowpath_common+0x50/0x64) from [<c0017950>] (warn_slowpath_null+0x1c/0x24)
[<c0017950>] (warn_slowpath_null+0x1c/0x24) from [<c00637cc>] (irq_linear_revmap+0x3c/0x44)
[<c00637cc>] (irq_linear_revmap+0x3c/0x44) from [<c00638b8>] (irq_create_mapping+0x20/0x118)
[<c00638b8>] (irq_create_mapping+0x20/0x118) from [<c0063a2c>] (irq_create_of_mapping+0x7c/0x100)
[<c0063a2c>] (irq_create_of_mapping+0x7c/0x100) from [<c022888c>] (irq_of_parse_and_map+0x30/0x38)
[<c022888c>] (irq_of_parse_and_map+0x30/0x38) from [<c02288ac>] (of_irq_to_resource+0x18/0x74)
[<c02288ac>] (of_irq_to_resource+0x18/0x74) from [<c02289b4>] (of_irq_to_resource_table+0x78/0x94)
[<c02289b4>] (of_irq_to_resource_table+0x78/0x94) from [<c0229130>] (of_device_alloc+0x154/0x248)
[<c0229130>] (of_device_alloc+0x154/0x248) from [<c0229260>] (of_platform_device_create_pdata+0x3c/0x80)
[<c0229260>] (of_platform_device_create_pdata+0x3c/0x80) from [<c0229378>] (of_platform_bus_create+0xd4/0x178)
[<c0229378>] (of_platform_bus_create+0xd4/0x178) from [<c0229558>] (of_platform_populate+0x60/0x98)
[<c0229558>] (of_platform_populate+0x60/0x98) from [<c0387714>] (customize_machine+0x20/0x28)
[<c0387714>] (customize_machine+0x20/0x28) from [<c0385888>] (do_one_initcall+0xa0/0x16c)
[<c0385888>] (do_one_initcall+0xa0/0x16c) from [<c0385a80>] (kernel_init_freeable+0x12c/0x1d0)
[<c0385a80>] (kernel_init_freeable+0x12c/0x1d0) from [<c02d39f8>] (kernel_init+0x8/0xe8)
[<c02d39f8>] (kernel_init+0x8/0xe8) from [<c0009e98>] (ret_from_fork+0x14/0x3c)
---[ end trace a30592ddc904989a ]---

No ATAGs?
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
sh_tmu sh_tmu.0: used for clock events
sh_tmu sh_tmu.0: used for periodic clock events
sh_tmu sh_tmu.1: used as clock source
Switching to clocksource sh_tmu.1
Clockevents: could not switch to one-shot mode:
Clockevents: could not switch to one-shot mode:
Clockevents: could not switch to one-shot mode:
dummy_timer is not functional.
dummy_timer is not functional.
Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
dummy_timer is not functional.
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
bounce pool size: 64 pages
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered (default)
gpio_rcar gpio_rcar.0: driving 32 GPIOs
gpio_rcar gpio_rcar.1: driving 32 GPIOs
gpio_rcar gpio_rcar.2: driving 32 GPIOs
gpio_rcar gpio_rcar.3: driving 32 GPIOs
gpio_rcar gpio_rcar.4: driving 32 GPIOs
gpio_rcar gpio_rcar.5: driving 32 GPIOs
gpio_rcar gpio_rcar.6: driving 9 GPIOs
SuperH SCI(F) driver initialized
sh-sci.0: ttySC0 at MMIO 0xffe40000 (irq = 120) is a scif
sh-sci.1: ttySC1 at MMIO 0xffe41000 (irq = 121) is a scif
sh-sci.2: ttySC2 at MMIO 0xffe42000 (irq = 122) is a scif
console [ttySC2] enabled
sh-sci.3: ttySC3 at MMIO 0xffe43000 (irq = 123) is a scif
sh-sci.4: ttySC4 at MMIO 0xffe44000 (irq = 124) is a scif
sh-sci.5: ttySC5 at MMIO 0xffe45000 (irq = 125) is a scif
scsi0 : sata_rcar
ata1: SATA max UDMA/133 irq 132
smsc911x: Driver version 2008-10-21
libphy: smsc911x-mdio: probed
smsc911x 18000000.lan0 eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=18000000.lan0-ff:01, irq=-1) smsc911x 18000000.lan0 eth0: MAC Address: 2e:09:0a:00:3c:de
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-platform: EHCI generic platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
rcar_thermal ffc48000.thermal: 1 sensor proved
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
ata1: link resume succeeded after 1 retries
ata1: SATA link down (SStatus 0 SControl 300)
smsc911x 18000000.lan0 eth0: ISR failed signaling test (IRQ 257)
IP-Config: Failed to open eth0
IP-Config: No network devices available

Freeing init memory: 2916K

boot (Linux 3.9.0-rc2-00003-gd779a6cb-dirty, BusyBox v1.16.0.git, kexec-tools 2.0.1-git) / #
/ # cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3

 59:          0          0          0          0       GIC  fe78001c.irqpin
 60:          0          0          0          0       GIC  fe78001c.irqpin
 61:          0          0          0          0       GIC  fe78001c.irqpin
 62:          0          0          0          0       GIC  fe78001c.irqpin
 64:       8493          0          0          0       GIC  sh_tmu.0
122:         48          0          0          0       GIC  sh-sci.2:mux
132:          0          0          0          0       GIC  sata_rcar
173:          0          0          0          0       GIC  gpio_rcar.0
174:          0          0          0          0       GIC  gpio_rcar.1
175:          0          0          0          0       GIC  gpio_rcar.2
176:          0          0          0          0       GIC  gpio_rcar.3
177:          0          0          0          0       GIC  gpio_rcar.4
178:          0          0          0          0       GIC  gpio_rcar.5
179:          0          0          0          0       GIC  gpio_rcar.6
257:          0          0          0          0  fe78001c.irqpin  eth0
IPI0:          0          0          0          0  CPU wakeup interrupts
IPI1:          0       7869       8493       8487  Timer broadcast interrupts
IPI2:        446        503         73         46  Rescheduling interrupts
IPI3:         21         37         54         56  Function call interrupts
IPI4:          0          0          0          0  Single function call interrupts
IPI5:          0          0          0          0  CPU stop interrupts
Err:          0

/ #

Boot log and /proc/interrupts with LAN patch (version without LAN patch is below):

Booting Linux on physical CPU 0x0
Linux version 3.9.0-rc2-00003-gd779a6cb (horms at ayumi.isobedori.kobe.vergenet.net) (gcc version 4.5.2 (Sourcery G++ Lite 2011.03-41) ) #1435 SMP Thu Apr 4 12:51:52 JST 2013
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: marzen, model: marzen
debug: ignoring loglevel setting.
Memory policy: ECC disabled, Data cache writealloc
On node 0 totalpages: 262144
free_area_init_node: node 0, pgdat c0683b00, node_mem_map c08fb000
Normal zone: 1520 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 194560 pages, LIFO batch:31
HighMem zone: 528 pages used for memmap
HighMem zone: 67584 pages, LIFO batch:15
PERCPU: Embedded 5 pages/cpu @c1103000 s6848 r0 d13632 u32768
pcpu-alloc: s6848 r0 d13632 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260624
Kernel command line: console=ttySC2,115200 earlyprintk=sh-sci.2,115200 ignore_loglevel root=/dev/nfs ip=on
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
__ex_table already sorted, skipping sort
Memory: 1024MB = 1024MB total
Memory: 1032628k/1032628k available, 15948k reserved, 270336K highmem
Virtual kernel memory layout:

    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
    lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
      .text : 0xc0008000 - 0xc0384e4c   (3572 kB)
      .init : 0xc0385000 - 0xc065eac0   (2919 kB)
      .data : 0xc0660000 - 0xc06846c0   ( 146 kB)
       .bss : 0xc06846c0 - 0xc06af174   ( 171 kB)

Hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
sched_clock: 32 bits at 1kHz, resolution 976562ns, wraps every 4194303999ms Calibrating delay loop (skipped) preset value.. 1000.00 BogoMIPS (lpj=488000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0xc02df328 - 0xc02df380
CPU1: Booted secondary processor
CPU2: Booted secondary processor
CPU3: Booted secondary processor
Brought up 4 CPUs
SMP: Total of 4 processors activated (4000.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations sh-pfc pfc-r8a7779: r8a7779_pfc support registered renesas_intc_irqpin fe78001c.irqpin: driving 4 irqs
No ATAGs?
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
sh_tmu sh_tmu.0: used for clock events
sh_tmu sh_tmu.0: used for periodic clock events
sh_tmu sh_tmu.1: used as clock source
Switching to clocksource sh_tmu.1
Clockevents: could not switch to one-shot mode:
Clockevents: could not switch to one-shot mode:
Clockevents: could not switch to one-shot mode:
dummy_timer is not functional.
dummy_timer is not functional.
Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
dummy_timer is not functional.
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
bounce pool size: 64 pages
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered
io scheduler deadline registered (default)
gpio_rcar gpio_rcar.0: driving 32 GPIOs
gpio_rcar gpio_rcar.1: driving 32 GPIOs
gpio_rcar gpio_rcar.2: driving 32 GPIOs
gpio_rcar gpio_rcar.3: driving 32 GPIOs
gpio_rcar gpio_rcar.4: driving 32 GPIOs
gpio_rcar gpio_rcar.5: driving 32 GPIOs
gpio_rcar gpio_rcar.6: driving 9 GPIOs
SuperH SCI(F) driver initialized
sh-sci.0: ttySC0 at MMIO 0xffe40000 (irq = 120) is a scif sh-sci.1: ttySC1 at MMIO 0xffe41000 (irq = 121) is a scif sh-sci.2: ttySC2 at MMIO 0xffe42000 (irq = 122) is a scif
console [ttySC2] enabled
sh-sci.3: ttySC3 at MMIO 0xffe43000 (irq = 123) is a scif sh-sci.4: ttySC4 at MMIO 0xffe44000 (irq = 124) is a scif sh-sci.5: ttySC5 at MMIO 0xffe45000 (irq = 125) is a scif
scsi0 : sata_rcar
ata1: SATA max UDMA/133 irq 132
smsc911x: Driver version 2008-10-21
genirq: Flags mismatch irq 60. 00000080 (eth%d) vs. 00000000 (fe78001c.irqpin)
smsc911x: probe of 18000000.lan0 failed with error -16
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-platform: EHCI generic platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
rcar_thermal ffc48000.thermal: 1 sensor proved
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
ata1: link resume succeeded after 1 retries
ata1: SATA link down (SStatus 0 SControl 300)
Freeing init memory: 2916K

boot (Linux 3.9.0-rc2-00003-gd779a6cb, BusyBox v1.16.0.git, kexec-tools 2.0.1-git) / # cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3

 59:          0          0          0          0       GIC  fe78001c.irqpin
 60:          0          0          0          0       GIC  fe78001c.irqpin
 61:          0          0          0          0       GIC  fe78001c.irqpin
 62:          0          0          0          0       GIC  fe78001c.irqpin
 64:      49198          0          0          0       GIC  sh_tmu.0
122:         45          0          0          0       GIC  sh-sci.2:mux
132:          0          0          0          0       GIC  sata_rcar
173:          0          0          0          0       GIC  gpio_rcar.0
174:          0          0          0          0       GIC  gpio_rcar.1
175:          0          0          0          0       GIC  gpio_rcar.2
176:          0          0          0          0       GIC  gpio_rcar.3
177:          0          0          0          0       GIC  gpio_rcar.4
178:          0          0          0          0       GIC  gpio_rcar.5
179:          0          0          0          0       GIC  gpio_rcar.6
IPI0:          0          0          0          0  CPU wakeup interrupts
IPI1:          0      49192      49198      48802  Timer broadcast interrupts
IPI2:        437        478         87         88  Rescheduling interrupts
IPI3:         56         37         36         39  Function call interrupts
IPI4:          0          0          0          0  Single function call interrupts
IPI5:          0          0          0          0  CPU stop interrupts
Quoted 2 lines

Err:

---
Guennadi Liakhovetski, Ph.D.
Freelance Open-Source Software Developer
http://www.open-technology.de/

#6 lore raw

cover ARM: shmobile: DT irqpin for r8a7779 and marzen-reference

Quoted 13 lines · Guennadi Liakhovetski

Hi Simon

Quoted 9 lines · Simon Horman
Quoted 7 lines · Guennadi Liakhovetski

Hi

This 2 patches add DT irqpin support on marzen-reference. Only compile-tested due to the lack of hardware. The patches can go independently via their respective trees. irqpin on marzen will not work if patch 2 is applied before patch 1, but as long as there are no devices, using irqpin interrupts, no breakage will be caused.

Quoted 8 lines
Quoted 4 lines

I have applied both patches and the dependency I mention below. I have also applied the small patch, inlined below, to hook-up the LAN controller. Unfortunately it doesn't seem to be receiving any interrupts. Perhaps I am missing something?

Are you sure 28 is the correct number in the irqpin IRQ space? Seems strange to me. Should be 1 perhaps (counting from 0), or 2 - not sure how that mapping would look like.

Thanks!

0 seems to be the lucky number, I have SMSC (and NFS root) working on marzen-reference.

I have posted "ARM: shmobile: marzen-reference: use irqpin for lan"

Quoted 9 lines
Quoted 5 lines
Quoted 2 lines

Guennadi Liakhovetski (2):
irqchip: renesas-intc-irqpin: DT binding for sense bitfield width

The above patch depends on "[1/3] ARM: shmobile: irqpin: fix handling of spurious interrupts in DT case", right?

Not functionally. Spurious interrupts occur on sh73a0, the sense bitfield is needed for r8a7779. But the latter won't apply without the former, that's right.

Thanks, could you reposts this series rebase so that it doesn't require ""[1/3] ARM: shmobile: irqpin: fix handling of spurious interrupts in DT case" to apply cleanly.

Feel free to break the creation of Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt into a separate patch.

Please add "ARM: shmobile: marzen-reference: use irqpin for lan" to the end of the series with an Ack if you have no objections to it.

Quoted 4 lines
Quoted 2 lines

Has there been any progress in your
discussions with Magnus about what to do about that patch?

No, not yet.

Thanks, understood.

And thanks doubly for this series.
It is very nice to have bouth irqpin and ethernet working on marzen-reference.

#7 lore raw

cover ARM: shmobile: DT irqpin for r8a7779 and marzen-reference

Quoted 19 lines · Simon Horman
Quoted 18 lines · Guennadi Liakhovetski

Hi Simon

Quoted 13 lines · Simon Horman
Quoted 7 lines · Guennadi Liakhovetski

Hi

This 2 patches add DT irqpin support on marzen-reference. Only compile-tested due to the lack of hardware. The patches can go independently via their respective trees. irqpin on marzen will not work if patch 2 is applied before patch 1, but as long as there are no devices, using irqpin interrupts, no breakage will be caused.

I have applied both patches and the dependency I mention below. I have also applied the small patch, inlined below, to hook-up the LAN controller. Unfortunately it doesn't seem to be receiving any interrupts. Perhaps I am missing something?

Quoted 8 lines
Quoted 3 lines

Are you sure 28 is the correct number in the irqpin IRQ space? Seems strange to me. Should be 1 perhaps (counting from 0), or 2 - not sure how that mapping would look like.

Thanks!

0 seems to be the lucky number, I have SMSC (and NFS root) working on marzen-reference.

s/0/1/

Quoted 38 lines

I have posted "ARM: shmobile: marzen-reference: use irqpin for lan"

Quoted 9 lines
Quoted 5 lines
Quoted 2 lines

Guennadi Liakhovetski (2):
irqchip: renesas-intc-irqpin: DT binding for sense bitfield width

The above patch depends on "[1/3] ARM: shmobile: irqpin: fix handling of spurious interrupts in DT case", right?

Not functionally. Spurious interrupts occur on sh73a0, the sense bitfield is needed for r8a7779. But the latter won't apply without the former, that's right.

Thanks, could you reposts this series rebase so that it doesn't require ""[1/3] ARM: shmobile: irqpin: fix handling of spurious interrupts in DT case" to apply cleanly.

Feel free to break the creation of Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt into a separate patch.

Please add "ARM: shmobile: marzen-reference: use irqpin for lan" to the end of the series with an Ack if you have no objections to it.

Quoted 4 lines
Quoted 2 lines

Has there been any progress in your
discussions with Magnus about what to do about that patch?

No, not yet.

Thanks, understood.

And thanks doubly for this series.
It is very nice to have bouth irqpin and ethernet working on marzen-reference.
--
To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo at vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html

#8 lore raw

cover ARM: shmobile: DT irqpin for r8a7779 and marzen-reference

Quoted 24 lines · Simon Horman
Quoted 23 lines · Simon Horman
Quoted 21 lines · Guennadi Liakhovetski

Hi Simon

Quoted 9 lines · Simon Horman
Quoted 7 lines · Guennadi Liakhovetski

Hi

This 2 patches add DT irqpin support on marzen-reference. Only compile-tested due to the lack of hardware. The patches can go independently via their respective trees. irqpin on marzen will not work if patch 2 is applied before patch 1, but as long as there are no devices, using irqpin interrupts, no breakage will be caused.

Quoted 4 lines

I have applied both patches and the dependency I mention below. I have also applied the small patch, inlined below, to hook-up the LAN controller. Unfortunately it doesn't seem to be receiving any interrupts. Perhaps I am missing something?

Are you sure 28 is the correct number in the irqpin IRQ space? Seems strange to me. Should be 1 perhaps (counting from 0), or 2 - not sure how that mapping would look like.

Quoted 6 lines
Quoted 4 lines

Thanks!

0 seems to be the lucky number, I have SMSC (and NFS root) working on marzen-reference.

s/0/1/

After all that it seems that I miss-tested the code somehow.

It turns out that 2 is the lucky number.

Quoted 43 lines
Quoted 30 lines

I have posted "ARM: shmobile: marzen-reference: use irqpin for lan"

Quoted 9 lines
Quoted 5 lines
Quoted 2 lines

Guennadi Liakhovetski (2):
irqchip: renesas-intc-irqpin: DT binding for sense bitfield width

The above patch depends on "[1/3] ARM: shmobile: irqpin: fix handling of spurious interrupts in DT case", right?

Not functionally. Spurious interrupts occur on sh73a0, the sense bitfield is needed for r8a7779. But the latter won't apply without the former, that's right.

Thanks, could you reposts this series rebase so that it doesn't require ""[1/3] ARM: shmobile: irqpin: fix handling of spurious interrupts in DT case" to apply cleanly.

Feel free to break the creation of Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt into a separate patch.

Please add "ARM: shmobile: marzen-reference: use irqpin for lan" to the end of the series with an Ack if you have no objections to it.

Quoted 4 lines
Quoted 2 lines

Has there been any progress in your
discussions with Magnus about what to do about that patch?

No, not yet.

Thanks, understood.

Quoted 8 lines

And thanks doubly for this series.
It is very nice to have bouth irqpin and ethernet working on marzen-reference.
--
To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo at vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html

--
To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo at vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html

#9 lore raw

cover ARM: shmobile: DT irqpin for r8a7779 and marzen-reference

Quoted 27 lines · Simon Horman
Quoted 26 lines · Simon Horman
Quoted 25 lines · Simon Horman
Quoted 13 lines · Guennadi Liakhovetski

Hi Simon

Quoted 9 lines · Simon Horman
Quoted 7 lines · Guennadi Liakhovetski

Hi

This 2 patches add DT irqpin support on marzen-reference. Only compile-tested due to the lack of hardware. The patches can go independently via their respective trees. irqpin on marzen will not work if patch 2 is applied before patch 1, but as long as there are no devices, using irqpin interrupts, no breakage will be caused.

Quoted 8 lines
Quoted 4 lines

I have applied both patches and the dependency I mention below. I have also applied the small patch, inlined below, to hook-up the LAN controller. Unfortunately it doesn't seem to be receiving any interrupts. Perhaps I am missing something?

Are you sure 28 is the correct number in the irqpin IRQ space? Seems strange to me. Should be 1 perhaps (counting from 0), or 2 - not sure how that mapping would look like.

Thanks!

Quoted 8 lines
Quoted 4 lines
Quoted 2 lines

0 seems to be the lucky number, I have SMSC (and NFS root) working on marzen-reference.

s/0/1/

After all that it seems that I miss-tested the code somehow.

It turns out that 2 is the lucky number.

My, what a mess I have made.

It seems that I miss-tested again (using non-reference boot instead of reference boot).

Unfortunately I am not able to get the NIC running after all.

Booting Linux on physical CPU 0x0
Linux version 3.9.0-rc2-00004-gb1480a8 (horms at ayumi.isobedori.kobe.vergenet.net) (gcc version 4.5.2 (Sourcery G++ Lite 2011.03-41) ) #1642 SMP Wed Apr 10 10:28:59 JST 2013
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: marzen, model: marzen
debug: ignoring loglevel setting.
Memory policy: ECC disabled, Data cache writealloc
On node 0 totalpages: 262144
free_area_init_node: node 0, pgdat c0534c00, node_mem_map c082b000
Normal zone: 1520 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 194560 pages, LIFO batch:31
HighMem zone: 528 pages used for memmap
HighMem zone: 67584 pages, LIFO batch:15
PERCPU: Embedded 5 pages/cpu @c1033000 s6720 r0 d13760 u32768
pcpu-alloc: s6720 r0 d13760 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260624
Kernel command line: console=ttySC2,115200 earlyprintk=sh-sci.2,115200 ignore_loglevel root=/dev/nfs ip=on
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
__ex_table already sorted, skipping sort
Memory: 1024MB = 1024MB total
Memory: 1033972k/1033972k available, 14604k reserved, 270336K highmem
Virtual kernel memory layout:

    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
    lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
      .text : 0xc0008000 - 0xc037fc60   (3552 kB)
      .init : 0xc0380000 - 0xc0511a40   (1607 kB)
      .data : 0xc0512000 - 0xc05357c0   ( 142 kB)
       .bss : 0xc05357c0 - 0xc0560274   ( 171 kB)

Hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
sched_clock: 32 bits at 1kHz, resolution 976562ns, wraps every 4194303999ms
Calibrating delay loop (skipped) preset value.. 1000.00 BogoMIPS (lpj=488000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0xc02db328 - 0xc02db380
CPU1: Booted secondary processor
CPU2: Booted secondary processor
CPU3: Booted secondary processor
Brought up 4 CPUs
SMP: Total of 4 processors activated (4000.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
sh-pfc pfc-r8a7779: r8a7779_pfc support registered
renesas_intc_irqpin fe78001c.irqpin: driving 4 irqs
No ATAGs?
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
sh_tmu sh_tmu.0: Runtime PM disabled, clock forced on.
sh_tmu sh_tmu.0: used for clock events
sh_tmu sh_tmu.0: used for periodic clock events
sh_tmu sh_tmu.1: Runtime PM disabled, clock forced on.
sh_tmu sh_tmu.1: used as clock source
Switching to clocksource sh_tmu.1
Clockevents: could not switch to one-shot mode:
Clockevents: could not switch to one-shot mode:
Clockevents: could not switch to one-shot mode:
dummy_timer is not functional.
dummy_timer is not functional.
Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
dummy_timer is not functional.
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
bounce pool size: 64 pages
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered (default)
gpio_rcar gpio_rcar.0: driving 32 GPIOs
gpio_rcar gpio_rcar.1: driving 32 GPIOs
gpio_rcar gpio_rcar.2: driving 32 GPIOs
gpio_rcar gpio_rcar.3: driving 32 GPIOs
gpio_rcar gpio_rcar.4: driving 32 GPIOs
gpio_rcar gpio_rcar.5: driving 32 GPIOs
gpio_rcar gpio_rcar.6: driving 9 GPIOs
SuperH SCI(F) driver initialized
sh-sci sh-sci.0: Runtime PM disabled, clock forced on.
sh-sci.0: ttySC0 at MMIO 0xffe40000 (irq = 120) is a scif
sh-sci sh-sci.1: Runtime PM disabled, clock forced on.
sh-sci.1: ttySC1 at MMIO 0xffe41000 (irq = 121) is a scif
sh-sci sh-sci.2: Runtime PM disabled, clock forced on.
sh-sci.2: ttySC2 at MMIO 0xffe42000 (irq = 122) is a scif
console [ttySC2] enabled
sh-sci sh-sci.3: Runtime PM disabled, clock forced on.
sh-sci.3: ttySC3 at MMIO 0xffe43000 (irq = 123) is a scif
sh-sci sh-sci.4: Runtime PM disabled, clock forced on.
sh-sci.4: ttySC4 at MMIO 0xffe44000 (irq = 124) is a scif
sh-sci sh-sci.5: Runtime PM disabled, clock forced on.
sh-sci.5: ttySC5 at MMIO 0xffe45000 (irq = 125) is a scif
sata_rcar fc600000.sata: Runtime PM disabled, clock forced on.
scsi0 : sata_rcar
ata1: SATA max UDMA/133 irq 132
smsc911x: Driver version 2008-10-21
libphy: smsc911x-mdio: probed
smsc911x 18000000.lan0 eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=18000000.lan0-ff:01, irq=-1) smsc911x 18000000.lan0 eth0: MAC Address: 2e:09:0a:00:3c:de
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-platform: EHCI generic platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
rcar_thermal ffc48000.thermal: 1 sensor proved
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
ata1: link resume succeeded after 1 retries
ata1: SATA link down (SStatus 0 SControl 300)
smsc911x 18000000.lan0 eth0: ISR failed signaling test (IRQ 256)
IP-Config: Failed to open eth0
IP-Config: No network devices available
Freeing init memory: 1604K

boot (Linux 3.9.0-rc2-00004-gb1480a8, BusyBox v1.16.0.git, kexec-tools 2.0.1-git) / # ip link set up dev eth0
smsc911x 18000000.lan0 eth0: ISR failed signaling test (IRQ 256)
ip: SIOCSIFFLAGS: No such device
/ # cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3

 59:          0          0          0          0       GIC  fe78001c.irqpin
 60:          0          0          0          0       GIC  fe78001c.irqpin
 61:          0          0          0          0       GIC  fe78001c.irqpin
 62:          0          0          0          0       GIC  fe78001c.irqpin
 64:      24370          0          0          0       GIC  sh_tmu.0
122:         97          0          0          0       GIC  sh-sci.2:mux
132:          0          0          0          0       GIC  sata_rcar
173:          0          0          0          0       GIC  gpio_rcar.0
174:          0          0          0          0       GIC  gpio_rcar.1
175:          0          0          0          0       GIC  gpio_rcar.2
176:          0          0          0          0       GIC  gpio_rcar.3
177:          0          0          0          0       GIC  gpio_rcar.4
178:          0          0          0          0       GIC  gpio_rcar.5
179:          0          0          0          0       GIC  gpio_rcar.6
256:          0          0          0          0  fe78001c.irqpin  eth0
IPI0:          0          0          0          0  CPU wakeup interrupts
IPI1:          0      24330      23977      24350  Timer broadcast interrupts
IPI2:        470        458         73         74  Rescheduling interrupts
IPI3:         56         37         40         35  Function call interrupts
IPI4:          0          0          0          0  Single function call interrupts
IPI5:          0          0          0          0  CPU stop interrupts
Err:          0