Add initial support for AQUILA-CYGNUS
v2 cover Add initial support for AQUILA-CYGNUS
IGEP COM AQUILA and CYGNUS are two computer-on-module based on AM3354 and AM3352 processors. Both use SODIMM from factor and are designed for industrial range purpose.
Changes since v1 (As Tom suggested)
* Remove ATAGS and FDT as we have no support.
* Remove CMD_EXT2 as is not required.
* Remove fdt related stuff from environment.
* Reduce the space dedicated to u-boot in MTDPARTS
* Remove SPL_NET, we don't use this.
Enric Balletbo i Serra (2):
Add DDR3 support for IGEP COM AQUILA/CYGNUS.
ARM: Add support for IGEP COM AQUILA/CYGNUS
MAINTAINERS | 1 + arch/arm/include/asm/arch-am33xx/ddr_defs.h | 17 ++ board/isee/igep0033/Makefile | 46 +++++ board/isee/igep0033/board.c | 232 ++++++++++++++++++++++ board/isee/igep0033/board.h | 27 +++ board/isee/igep0033/mux.c | 89 +++++++++ boards.cfg | 1 + include/configs/igep0033.h | 284 +++++++++++++++++++++++++++ 8 files changed, 697 insertions(+) create mode 100644 board/isee/igep0033/Makefile create mode 100644 board/isee/igep0033/board.c create mode 100644 board/isee/igep0033/board.h create mode 100644 board/isee/igep0033/mux.c create mode 100644 include/configs/igep0033.h
Signature · 1 line
1.7.10.4
PATCH v2 1/2 Add DDR3 support for IGEP COM AQUILA/CYGNUS.
These boards uses Samsung K4B2G1646E-BIH9 a 2Gb E-die DDR3 SDRAM.
--- arch/arm/include/asm/arch-am33xx/ddr_defs.h | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)
arch/arm/include/asm/arch-am33xx/ddr_defs.h +17 -0
@@ -117,6 +117,23 @@#define MT41J512M8RH125_PHY_WR_DATA 0x74#define MT41J512M8RH125_IOCTRL_VALUE 0x18B +/* Samsung K4B2G1646E-BIH9 */ +#define K4B2G1646EBIH9_EMIF_READ_LATENCY 0x06 +#define K4B2G1646EBIH9_EMIF_TIM1 0x0888A39B +#define K4B2G1646EBIH9_EMIF_TIM2 0x2A04011A +#define K4B2G1646EBIH9_EMIF_TIM3 0x501F820F +#define K4B2G1646EBIH9_EMIF_SDCFG 0x61C24AB2 +#define K4B2G1646EBIH9_EMIF_SDREF 0x0000093B +#define K4B2G1646EBIH9_ZQ_CFG 0x50074BE4 +#define K4B2G1646EBIH9_DLL_LOCK_DIFF 0x1 +#define K4B2G1646EBIH9_RATIO 0x40 +#define K4B2G1646EBIH9_INVERT_CLKOUT 0x1 +#define K4B2G1646EBIH9_RD_DQS 0x3B +#define K4B2G1646EBIH9_WR_DQS 0x85 +#define K4B2G1646EBIH9_PHY_FIFO_WE 0x100 +#define K4B2G1646EBIH9_PHY_WR_DATA 0xC1 +#define K4B2G1646EBIH9_IOCTRL_VALUE 0x18B +/** * Configure DMM */
Signature · 1 line
1.7.10.4
PATCH v2 1/2 Add DDR3 support for IGEP COM AQUILA/CYGNUS.
Quoted 3 lines · Enric Balletbo i Serra
These boards uses Samsung K4B2G1646E-BIH9 a 2Gb E-die DDR3 SDRAM.
Signed-off-by Enric Balletbo i Serra <[email protected]>
Along with 2/2, applied to u-boot-ti/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130429/68cd88cf/attachment.pgp>
PATCH v2 2/2 ARM: Add support for IGEP COM AQUILA/CYGNUS
In reply to Enric Balletbo i SerraThe IGEP COM AQUILA and CYGNUS are industrial processors modules with following highlights:
o AM3352/AM3354 Texas Instruments processor
o Cortex-A8 ARM CPU
o 3.3 volts Inputs / Outputs use industrial
o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
o MicroSD card reader on-board
o Ethernet controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
--- MAINTAINERS | 1 + board/isee/igep0033/Makefile | 46 +++++++ board/isee/igep0033/board.c | 232 ++++++++++++++++++++++++++++++++++ board/isee/igep0033/board.h | 27 ++++ board/isee/igep0033/mux.c | 89 +++++++++++++ boards.cfg | 1 + include/configs/igep0033.h | 284 ++++++++++++++++++++++++++++++++++++++++++ 7 files changed, 680 insertions(+) create mode 100644 board/isee/igep0033/Makefile create mode 100644 board/isee/igep0033/board.c create mode 100644 board/isee/igep0033/board.h create mode 100644 board/isee/igep0033/mux.c create mode 100644 include/configs/igep0033.h
MAINTAINERS +1 -0
@@ -607,6 +607,7 @@ Enric Balletbo i Serra <[email protected]> igep0020 ARM ARMV7 (OMAP3xx SoC) igep0030 ARM ARMV7 (OMAP3xx SoC) igep0032 ARM ARMV7 (OMAP3xx SoC) + igep0033 ARM ARMV7 (AM33xx Soc) Eric Benard <[email protected]>
board/isee/igep0033/Makefile new file +46 -0
46 lines not on this page · raw message
board/isee/igep0033/board.c new file +232 -0
232 lines not on this page · raw message
board/isee/igep0033/board.h new file +27 -0
@@ -0,0 +1,27 @@ +/* +* IGEP COM AQUILA/CYGNUS boards information header +* +* Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/ +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the +* GNU General Public License for more details. +*/ + +#ifndef _BOARD_H_ +#define _BOARD_H_ + +/* +* We must be able to enable uart0, for initial output. We then have a +* main pinmux function that can be overridden to enable all other pinmux that +* is required on the board. +*/ +void enable_uart0_pin_mux (void ); +void enable_board_pin_mux (void ); +#endif
board/isee/igep0033/mux.c new file +89 -0
89 lines not on this page · raw message
boards.cfg +1 -0
@@ -273,6 +273,7 @@ igep0020_nand arm armv7 igep00x0 isee igep0030 arm armv7 igep00x0 isee omap3 igep00x0:MACH_TYPE=MACH_TYPE_IGEP0030,BOOT_ONENAND igep0030_nand arm armv7 igep00x0 isee omap3 igep00x0:MACH_TYPE=MACH_TYPE_IGEP0030,BOOT_NAND igep0032 arm armv7 igep00x0 isee omap3 igep00x0:MACH_TYPE=MACH_TYPE_IGEP0032,BOOT_ONENAND +igep0033 arm armv7 igep0033 isee am33xx am3517_evm arm armv7 am3517evm logicpd omap3 mt_ventoux arm armv7 mt_ventoux teejet omap3 omap3_zoom1 arm armv7 zoom1 logicpd omap3
include/configs/igep0033.h new file +284 -0
284 lines not on this page · raw message
Signature · 1 line
1.7.10.4