Skip to contentSkip to conversation

HID: hid-sensor-hub: do not process feature reports in raw_event

PATCH In review [email protected] 3 participants 9 messages Mar 21, 2013 – May 29, 2013

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 HID: hid-sensor-hub: do not process feature reports in raw_event

From: Daniel Leung <[email protected]>

In sensor_hub_raw_event(), HID feature reports are ignored but are still marked as processed. This causes the in-kernel struct not to be updated. Any non-updated fields in the feature reports are zero, and they are being sent to the device. This causes confusion in the sensor hub firmware, and some sensors are not powered up as a result.

This changes the raw_event rountine to only process input reports, and let the hid core handle the incoming feature reports.

The issue has been observed on Acer Iconia W700.

---
 drivers/hid/hid-sensor-hub.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/hid/hid-sensor-hub.c +1 -1
index ca749810..3f7df68 100644
@@ -413,7 +413,7 @@ static int sensor_hub_raw_event(struct hid_device *hdev,
 			 report->id, size, report->type);
 	hid_dbg(hdev, "maxfield:%d\n", report->maxfield);
 	if (report->type != HID_INPUT_REPORT)
-		return 1;
+		return 0;
 
 	ptr = raw_data;
 	ptr++; /*Skip report id*/
Signature · 1 line
1.8.1.5
#1 lore raw

Daniel,

I am looking at 3.9.rc1.
The only place I see the raw_event callback is called from hid/hid_input_report(). hid_input_report is called with type HID_INPUT_REPORT in all cases, except hid_ctrl(), where it can be different depending on xx.report->type. But here, the return value is not checked.

Do you know the call chain for HID_FETURE_REPORT, where this is creating problem?

Thanks,
Srinivas

Quoted 31 lines · On 03/21/2013 10:22 AM, [email protected] wrote:

From: Daniel Leung <[email protected]>

In sensor_hub_raw_event(), HID feature reports are ignored but are still marked as processed. This causes the in-kernel struct not to be updated. Any non-updated fields in the feature reports are zero, and they are being sent to the device. This causes confusion in the sensor hub firmware, and some sensors are not powered up as a result.

This changes the raw_event rountine to only process input reports, and let the hid core handle the incoming feature reports.

The issue has been observed on Acer Iconia W700.

---
  drivers/hid/hid-sensor-hub.c | 2 +-
  1 file changed, 1 insertion(+), 1 deletion(-)
drivers/hid/hid-sensor-hub.c +1 -1
index ca749810..3f7df68 100644
@@ -413,7 +413,7 @@ static int sensor_hub_raw_event(struct hid_device *hdev,
  			 report->id, size, report->type);
  	hid_dbg(hdev, "maxfield:%d\n", report->maxfield);
  	if (report->type != HID_INPUT_REPORT)
-		return 1;
+		return 0;
 
  	ptr = raw_data;
  	ptr++; /*Skip report id*/
#2 lore raw
Quoted 10 lines · Srinivas Pandruvada

Daniel,

I am looking at 3.9.rc1.
The only place I see the raw_event callback is called from hid/hid_input_report(). hid_input_report is called with type HID_INPUT_REPORT in all cases, except hid_ctrl(), where it can be different depending on xx.report->type. But here, the return value is not checked.

Do you know the call chain for HID_FETURE_REPORT, where this is creating problem?

This was exactly what I was wondering about when I have seen the initial patch a few weeks ago.

Daniel, could you please elaborate? Is there a out-of-tree driver for Acer Iconia W700?

Thanks,

Signature · 2 lines
Jiri Kosina
SUSE Labs
#3 lore raw
Quoted 6 lines · Jiri Kosina
Quoted 6 lines

I am looking at 3.9.rc1.
The only place I see the raw_event callback is called from hid/hid_input_report(). hid_input_report is called with type HID_INPUT_REPORT in all cases, except hid_ctrl(), where it can be different depending on xx.report->type. But here, the return value is not checked.

Quoted 8 lines
Quoted 2 lines

Do you know the call chain for HID_FETURE_REPORT, where this is creating problem?

This was exactly what I was wondering about when I have seen the initial patch a few weeks ago.

Daniel, could you please elaborate? Is there a out-of-tree driver for Acer Iconia W700?

Daniel ... ?

Signature · 2 lines
Jiri Kosina
SUSE Labs
#4 lore raw
In reply to Jiri Kosina
Quoted 11 lines · Srinivas Pandruvada
Quoted 10 lines

Daniel,

I am looking at 3.9.rc1.
The only place I see the raw_event callback is called from hid/hid_input_report(). hid_input_report is called with type HID_INPUT_REPORT
in all cases, except hid_ctrl(), where it can be different depending on xx.report->type. But here, the return value is not checked.

Quoted 8 lines
Quoted 2 lines

Do you know the call chain for HID_FETURE_REPORT, where this is creating problem?

This was exactly what I was wondering about when I have seen the initial patch a few weeks ago.

Daniel, could you please elaborate? Is there a out-of-tree driver for Acer Iconia W700?

Sorry for the late reply. I was out of town and was having difficulties accessing the mail server.

For the call path, here is what I got (using WARN_ON()):

<4>[  150.943775] ------------[ cut here ]------------
<4>[  150.943861] WARNING: at
../../../../../../../../../../home/dleung/android/ia/private/jb-mr1-internal/kernel/intel/drivers/hid/hid-sensor-hub.c:418
sensor_hub_raw_event+0x2d0/0x3b0 [hid_sensor_hub]()
<4>[  150.944028] Hardware name: ICONIA W700
<7>[  150.944071] Modules linked in: hid_sensor_als hid_sensor_gyro_3d

hid_sensor_accel_3d uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_core btusb bluetooth hid_multitouch ath9k ath9k_common ath9k_hw ath snd_hda_codec_hdmi snd_hda_codec_realtek ip6table_raw snd_hda_intel iptable_raw snd_hda_codec snd_hwdep snd_pcm snd_page_alloc snd_timer snd soundcore hid_sensor_trigger hid_sensor_iio_common hid_sensor_hub industrialio_triggered_buffer kfifo_buf industrialio coretemp

<7>[  150.944132] Pid: 0, comm: swapper/1 Not tainted
3.8.0-aia1-00043-gd7fd780-dirty #2
<7>[  150.944136] Call Trace:
<7>[  150.944141]  <IRQ>  [<ffffffff8105b5bf>] warn_slowpath_common+0x7f/0xc0
<7>[  150.944163]  [<ffffffff8105b61a>] warn_slowpath_null+0x1a/0x20
<7>[  150.944173]  [<ffffffffa00315e0>] sensor_hub_raw_event+0x2d0/0x3b0
[hid_sensor_hub]
<7>[  150.944184]  [<ffffffff819021e7>] ?
_raw_spin_unlock_irqrestore+0x57/0x70
<7>[  150.944195]  [<ffffffff816ccce3>] hid_input_report+0x283/0x2d0
<7>[  150.944203]  [<ffffffff816d9faf>] hid_ctrl+0x9f/0x180
<7>[  150.944212]  [<ffffffff815b2087>] usb_hcd_giveback_urb+0x77/0x110
<7>[  150.944222]  [<ffffffff8160073f>] xhci_irq+0x60f/0x1530
<7>[  150.944230]  [<ffffffff810df0fe>] ? handle_edge_irq+0x1e/0x130
<7>[  150.944239]  [<ffffffff810af04f>] ? __lock_acquire.isra.31+0x28f/0xa70
<7>[  150.944247]  [<ffffffff81601671>] xhci_msi_irq+0x11/0x20
<7>[  150.944258]  [<ffffffff810dc395>] handle_irq_event_percpu+0x55/0x210
<7>[  150.944267]  [<ffffffff810dc598>] handle_irq_event+0x48/0x70
<7>[  150.944273]  [<ffffffff810df157>] handle_edge_irq+0x77/0x130
<7>[  150.944283]  [<ffffffff81004180>] handle_irq+0x60/0x150
<7>[  150.944293]  [<ffffffff81906406>] ?
atomic_notifier_call_chain+0x16/0x20
<7>[  150.944302]  [<ffffffff8190c38a>] do_IRQ+0x5a/0xe0
<7>[  150.944309]  [<ffffffff8190266f>] common_interrupt+0x6f/0x6f
<7>[  150.944313]  <EOI>  [<ffffffff816a97f5>] ? cpuidle_wrap_enter+0x55/0xa0
<7>[  150.944327]  [<ffffffff816a97f1>] ? cpuidle_wrap_enter+0x51/0xa0
<7>[  150.944334]  [<ffffffff816a9850>] cpuidle_enter_tk+0x10/0x20
<7>[  150.944341]  [<ffffffff816a940f>] cpuidle_idle_call+0xaf/0x2b0
<7>[  150.944350]  [<ffffffff8100b3aa>] cpu_idle+0xda/0x130
<7>[  150.944360]  [<ffffffff818f081d>] start_secondary+0x266/0x268
<4>[  150.944365] ---[ end trace 32319d39ebee5616 ]---

You can see that it went through hid_ctrl().

Quoted 1 line

From what I can gather using usbmon, the sensor hub sends the feature

report correctly. However, the in-kernel struct is not updated when the report comes in. Therefore, the report from sensor_hub_report() is always zero-filled. When calling sensor_hub_set_feature(), those zeros are being sent back to the device. The feature report contains fields for power state and reporting state. If they are set to zero, the firmware does not know what to do as zero means undefined state. Both power and reporting states have to be set for sensor to report values. Given the zero-filled report, and we can only deal with one field in sensor_hub_set_feature(), setting power state to non-zero also sends zero (i.e. undefined state) to the reporting state field, and vice versa.

The sensor hub on Acer Iconia W700 is using drivers/hid/hid-sensor-hub.c. I also played with Sony Vaio Duo 11 a while back (before having this patch), and was having trouble turning on gyroscope. I suspect it is caused by the same issue. The sensor hub on Acer is from STMicro, while the one in Vaio Duo is from Freescale.

Thanks,
Daniel

#5 lore raw
Quoted 89 lines
Quoted 15 lines · Srinivas Pandruvada
Quoted 10 lines

Daniel,

I am looking at 3.9.rc1.
The only place I see the raw_event callback is called from hid/hid_input_report(). hid_input_report is called with type HID_INPUT_REPORT
in all cases, except hid_ctrl(), where it can be different depending on xx.report->type. But here, the return value is not checked.

Quoted 3 lines

Do you know the call chain for HID_FETURE_REPORT, where this is creating
problem?

Quoted 6 lines

This was exactly what I was wondering about when I have seen the initial patch a few weeks ago.

Daniel, could you please elaborate? Is there a out-of-tree driver for Acer
Iconia W700?

Sorry for the late reply. I was out of town and was having difficulties accessing the mail server.

For the call path, here is what I got (using WARN_ON()):

<4>[  150.943775] ------------[ cut here ]------------
<4>[  150.943861] WARNING: at
../../../../../../../../../../home/dleung/android/ia/private/jb-mr1-internal/kernel/intel/drivers/hid/hid-sensor-hub.c:418
sensor_hub_raw_event+0x2d0/0x3b0 [hid_sensor_hub]()
<4>[  150.944028] Hardware name: ICONIA W700
<7>[  150.944071] Modules linked in: hid_sensor_als hid_sensor_gyro_3d

hid_sensor_accel_3d uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_core btusb bluetooth hid_multitouch ath9k ath9k_common ath9k_hw ath snd_hda_codec_hdmi snd_hda_codec_realtek ip6table_raw snd_hda_intel iptable_raw snd_hda_codec snd_hwdep snd_pcm snd_page_alloc snd_timer snd soundcore hid_sensor_trigger hid_sensor_iio_common hid_sensor_hub industrialio_triggered_buffer kfifo_buf industrialio coretemp

<7>[  150.944132] Pid: 0, comm: swapper/1 Not tainted
3.8.0-aia1-00043-gd7fd780-dirty #2
<7>[  150.944136] Call Trace:
<7>[  150.944141]  <IRQ>  [<ffffffff8105b5bf>]
warn_slowpath_common+0x7f/0xc0
<7>[  150.944163]  [<ffffffff8105b61a>] warn_slowpath_null+0x1a/0x20
<7>[  150.944173]  [<ffffffffa00315e0>] sensor_hub_raw_event+0x2d0/0x3b0
[hid_sensor_hub]
<7>[  150.944184]  [<ffffffff819021e7>] ?
_raw_spin_unlock_irqrestore+0x57/0x70
<7>[  150.944195]  [<ffffffff816ccce3>] hid_input_report+0x283/0x2d0
<7>[  150.944203]  [<ffffffff816d9faf>] hid_ctrl+0x9f/0x180
<7>[  150.944212]  [<ffffffff815b2087>] usb_hcd_giveback_urb+0x77/0x110
<7>[  150.944222]  [<ffffffff8160073f>] xhci_irq+0x60f/0x1530
<7>[  150.944230]  [<ffffffff810df0fe>] ? handle_edge_irq+0x1e/0x130
<7>[  150.944239]  [<ffffffff810af04f>] ?
__lock_acquire.isra.31+0x28f/0xa70
<7>[  150.944247]  [<ffffffff81601671>] xhci_msi_irq+0x11/0x20
<7>[  150.944258]  [<ffffffff810dc395>] handle_irq_event_percpu+0x55/0x210
<7>[  150.944267]  [<ffffffff810dc598>] handle_irq_event+0x48/0x70
<7>[  150.944273]  [<ffffffff810df157>] handle_edge_irq+0x77/0x130
<7>[  150.944283]  [<ffffffff81004180>] handle_irq+0x60/0x150
<7>[  150.944293]  [<ffffffff81906406>] ?
atomic_notifier_call_chain+0x16/0x20
<7>[  150.944302]  [<ffffffff8190c38a>] do_IRQ+0x5a/0xe0
<7>[  150.944309]  [<ffffffff8190266f>] common_interrupt+0x6f/0x6f
<7>[  150.944313]  <EOI>  [<ffffffff816a97f5>] ?
cpuidle_wrap_enter+0x55/0xa0
<7>[  150.944327]  [<ffffffff816a97f1>] ? cpuidle_wrap_enter+0x51/0xa0
<7>[  150.944334]  [<ffffffff816a9850>] cpuidle_enter_tk+0x10/0x20
<7>[  150.944341]  [<ffffffff816a940f>] cpuidle_idle_call+0xaf/0x2b0
<7>[  150.944350]  [<ffffffff8100b3aa>] cpu_idle+0xda/0x130
<7>[  150.944360]  [<ffffffff818f081d>] start_secondary+0x266/0x268
<4>[  150.944365] ---[ end trace 32319d39ebee5616 ]---

You can see that it went through hid_ctrl().

From what I can gather using usbmon, the sensor hub sends the feature report correctly. However, the in-kernel struct is not updated when the report comes in. Therefore, the report from sensor_hub_report() is always zero-filled. When calling sensor_hub_set_feature(), those zeros are being sent back to the device. The feature report contains fields for power state and reporting state. If they are set to zero, the firmware does not know what to do as zero means undefined state. Both power and reporting states have to be set for sensor to report values. Given the zero-filled report, and we can only deal with one field in sensor_hub_set_feature(), setting power state to non-zero also sends zero (i.e. undefined state) to the reporting state field, and vice versa.

Quoted 5 lines

The sensor hub on Acer Iconia W700 is using drivers/hid/hid-sensor-hub.c. I also played with Sony Vaio Duo 11 a while back (before having this patch), and was having trouble turning on gyroscope. I suspect it is caused by the same issue. The sensor hub on Acer is from STMicro, while the one in Vaio Duo is from Freescale.

Just to clarify a little bit on the issue.

Although hid_ctrl() does not care the return value of hid_input_report(), the issue is within hid_input_report(). In drivers/hid/hid-core.c:1317 where raw_event() is called, if return is non-zero, the following call of hid_report_raw_event() is skipped. This call is needed to have the in-kernel struct updated with the actual feature report from device.

Daniel

#6 lore raw

Thanks Daniel.

I don't know if this should be fixed in client drivers since other drivers may have this issue.

I interpret the return value of hdrv->raw_event as :
"<0" : Error. The driver has parsed the message and found issue
"==0" : No error and driver has consumed report
">0" : Not an error and driver has not parsed or consumed the event

In this case hid-sensor-hub didn't parse message to return any error or to say consumed.

May be hid-core.c

       if (hdrv && hdrv->raw_event && hid_match_report(hid, report)) {
                ret = hdrv->raw_event(hid, report, data, size);
                if (ret < 0) {
                        goto unlock;
                }
        }

I think Jiri can have better idea.

Thanks,
Srinivas

Quoted 107 lines · Daniel Leung
Quoted 87 lines
Quoted 14 lines · Srinivas Pandruvada
Quoted 10 lines

Daniel,

I am looking at 3.9.rc1.
The only place I see the raw_event callback is called from hid/hid_input_report(). hid_input_report is called with type HID_INPUT_REPORT
in all cases, except hid_ctrl(), where it can be different depending on xx.report->type. But here, the return value is not checked.

Quoted 3 lines

Do you know the call chain for HID_FETURE_REPORT, where this is creating
problem?

Quoted 6 lines

This was exactly what I was wondering about when I have seen the initial patch a few weeks ago.

Daniel, could you please elaborate? Is there a out-of-tree driver for Acer
Iconia W700?

Sorry for the late reply. I was out of town and was having difficulties accessing the mail server.

For the call path, here is what I got (using WARN_ON()):

<4>[  150.943775] ------------[ cut here ]------------
<4>[  150.943861] WARNING: at
../../../../../../../../../../home/dleung/android/ia/private/jb-mr1-internal/kernel/intel/drivers/hid/hid-sensor-hub.c:418
sensor_hub_raw_event+0x2d0/0x3b0 [hid_sensor_hub]()
<4>[  150.944028] Hardware name: ICONIA W700
<7>[  150.944071] Modules linked in: hid_sensor_als hid_sensor_gyro_3d

hid_sensor_accel_3d uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_core btusb bluetooth hid_multitouch ath9k ath9k_common ath9k_hw ath snd_hda_codec_hdmi snd_hda_codec_realtek ip6table_raw snd_hda_intel iptable_raw snd_hda_codec snd_hwdep snd_pcm snd_page_alloc snd_timer snd soundcore hid_sensor_trigger hid_sensor_iio_common hid_sensor_hub industrialio_triggered_buffer kfifo_buf industrialio coretemp

<7>[  150.944132] Pid: 0, comm: swapper/1 Not tainted
3.8.0-aia1-00043-gd7fd780-dirty #2
<7>[  150.944136] Call Trace:
<7>[  150.944141]  <IRQ>  [<ffffffff8105b5bf>]
warn_slowpath_common+0x7f/0xc0
<7>[  150.944163]  [<ffffffff8105b61a>] warn_slowpath_null+0x1a/0x20
<7>[  150.944173]  [<ffffffffa00315e0>] sensor_hub_raw_event+0x2d0/0x3b0
[hid_sensor_hub]
<7>[  150.944184]  [<ffffffff819021e7>] ?
_raw_spin_unlock_irqrestore+0x57/0x70
<7>[  150.944195]  [<ffffffff816ccce3>] hid_input_report+0x283/0x2d0
<7>[  150.944203]  [<ffffffff816d9faf>] hid_ctrl+0x9f/0x180
<7>[  150.944212]  [<ffffffff815b2087>] usb_hcd_giveback_urb+0x77/0x110
<7>[  150.944222]  [<ffffffff8160073f>] xhci_irq+0x60f/0x1530
<7>[  150.944230]  [<ffffffff810df0fe>] ? handle_edge_irq+0x1e/0x130
<7>[  150.944239]  [<ffffffff810af04f>] ?
__lock_acquire.isra.31+0x28f/0xa70
<7>[  150.944247]  [<ffffffff81601671>] xhci_msi_irq+0x11/0x20
<7>[  150.944258]  [<ffffffff810dc395>] handle_irq_event_percpu+0x55/0x210
<7>[  150.944267]  [<ffffffff810dc598>] handle_irq_event+0x48/0x70
<7>[  150.944273]  [<ffffffff810df157>] handle_edge_irq+0x77/0x130
<7>[  150.944283]  [<ffffffff81004180>] handle_irq+0x60/0x150
<7>[  150.944293]  [<ffffffff81906406>] ?
atomic_notifier_call_chain+0x16/0x20
<7>[  150.944302]  [<ffffffff8190c38a>] do_IRQ+0x5a/0xe0
<7>[  150.944309]  [<ffffffff8190266f>] common_interrupt+0x6f/0x6f
<7>[  150.944313]  <EOI>  [<ffffffff816a97f5>] ?
cpuidle_wrap_enter+0x55/0xa0
<7>[  150.944327]  [<ffffffff816a97f1>] ? cpuidle_wrap_enter+0x51/0xa0
<7>[  150.944334]  [<ffffffff816a9850>] cpuidle_enter_tk+0x10/0x20
<7>[  150.944341]  [<ffffffff816a940f>] cpuidle_idle_call+0xaf/0x2b0
<7>[  150.944350]  [<ffffffff8100b3aa>] cpu_idle+0xda/0x130
<7>[  150.944360]  [<ffffffff818f081d>] start_secondary+0x266/0x268
<4>[  150.944365] ---[ end trace 32319d39ebee5616 ]---

You can see that it went through hid_ctrl().

From what I can gather using usbmon, the sensor hub sends the feature
report correctly. However, the in-kernel struct is not updated when the report comes in. Therefore, the report from sensor_hub_report() is always zero-filled. When calling sensor_hub_set_feature(), those zeros are being sent back to the device. The feature report contains fields for power state and reporting state. If they are set to zero, the firmware does not know what to do as zero means undefined state. Both power and reporting states have to be set for sensor to report values. Given the zero-filled report, and we can only deal with one field in sensor_hub_set_feature(), setting power state to non-zero also sends zero (i.e. undefined state) to the reporting state field, and vice versa.

Quoted 5 lines

The sensor hub on Acer Iconia W700 is using drivers/hid/hid-sensor-hub.c. I also played with Sony Vaio Duo 11 a while back (before having this patch), and was having trouble turning on gyroscope. I suspect it is caused by the same issue. The sensor hub on Acer is from STMicro, while the one in Vaio Duo is from Freescale.

Just to clarify a little bit on the issue.

Although hid_ctrl() does not care the return value of hid_input_report(), the issue is within hid_input_report(). In drivers/hid/hid-core.c:1317 where raw_event() is called, if return is non-zero, the following call of hid_report_raw_event() is skipped. This call is needed to have the in-kernel struct updated with the actual feature report from device.

Daniel
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#7 lore raw

Jiri, ping?

Daniel

Quoted 141 lines

On Wed, 10 Apr 2013 08:44:34 -0700
Srinivas Pandruvada <[email protected]> wrote:

Thanks Daniel.

I don't know if this should be fixed in client drivers since other drivers may have this issue.

I interpret the return value of hdrv->raw_event as :
"<0" : Error. The driver has parsed the message and found issue
"==0" : No error and driver has consumed report
">0" : Not an error and driver has not parsed or consumed the event

In this case hid-sensor-hub didn't parse message to return any error or to say consumed.

May be hid-core.c

        if (hdrv && hdrv->raw_event && hid_match_report(hid, report)) {
                 ret = hdrv->raw_event(hid, report, data, size);
                 if (ret < 0) {
                         goto unlock;
                 }
         }

I think Jiri can have better idea.

Thanks,
Srinivas

Quoted 107 lines · Daniel Leung
Quoted 87 lines
Quoted 14 lines · Srinivas Pandruvada
Quoted 10 lines

Daniel,

I am looking at 3.9.rc1.
The only place I see the raw_event callback is called from hid/hid_input_report(). hid_input_report is called with type HID_INPUT_REPORT
in all cases, except hid_ctrl(), where it can be different depending on xx.report->type. But here, the return value is not checked.

Quoted 3 lines

Do you know the call chain for HID_FETURE_REPORT, where this is creating
problem?

Quoted 6 lines

This was exactly what I was wondering about when I have seen the initial patch a few weeks ago.

Daniel, could you please elaborate? Is there a out-of-tree driver for Acer
Iconia W700?

Sorry for the late reply. I was out of town and was having difficulties accessing the mail server.

For the call path, here is what I got (using WARN_ON()):

<4>[  150.943775] ------------[ cut here ]------------
<4>[  150.943861] WARNING: at
../../../../../../../../../../home/dleung/android/ia/private/jb-mr1-internal/kernel/intel/drivers/hid/hid-sensor-hub.c:418
sensor_hub_raw_event+0x2d0/0x3b0 [hid_sensor_hub]()
<4>[  150.944028] Hardware name: ICONIA W700
<7>[  150.944071] Modules linked in: hid_sensor_als hid_sensor_gyro_3d

hid_sensor_accel_3d uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_core btusb bluetooth hid_multitouch ath9k ath9k_common ath9k_hw ath snd_hda_codec_hdmi snd_hda_codec_realtek ip6table_raw snd_hda_intel iptable_raw snd_hda_codec snd_hwdep snd_pcm snd_page_alloc snd_timer snd soundcore hid_sensor_trigger hid_sensor_iio_common hid_sensor_hub industrialio_triggered_buffer kfifo_buf industrialio coretemp

<7>[  150.944132] Pid: 0, comm: swapper/1 Not tainted
3.8.0-aia1-00043-gd7fd780-dirty #2
<7>[  150.944136] Call Trace:
<7>[  150.944141]  <IRQ>  [<ffffffff8105b5bf>]
warn_slowpath_common+0x7f/0xc0
<7>[  150.944163]  [<ffffffff8105b61a>] warn_slowpath_null+0x1a/0x20
<7>[  150.944173]  [<ffffffffa00315e0>] sensor_hub_raw_event+0x2d0/0x3b0
[hid_sensor_hub]
<7>[  150.944184]  [<ffffffff819021e7>] ?
_raw_spin_unlock_irqrestore+0x57/0x70
<7>[  150.944195]  [<ffffffff816ccce3>] hid_input_report+0x283/0x2d0
<7>[  150.944203]  [<ffffffff816d9faf>] hid_ctrl+0x9f/0x180
<7>[  150.944212]  [<ffffffff815b2087>] usb_hcd_giveback_urb+0x77/0x110
<7>[  150.944222]  [<ffffffff8160073f>] xhci_irq+0x60f/0x1530
<7>[  150.944230]  [<ffffffff810df0fe>] ? handle_edge_irq+0x1e/0x130
<7>[  150.944239]  [<ffffffff810af04f>] ?
__lock_acquire.isra.31+0x28f/0xa70
<7>[  150.944247]  [<ffffffff81601671>] xhci_msi_irq+0x11/0x20
<7>[  150.944258]  [<ffffffff810dc395>] handle_irq_event_percpu+0x55/0x210
<7>[  150.944267]  [<ffffffff810dc598>] handle_irq_event+0x48/0x70
<7>[  150.944273]  [<ffffffff810df157>] handle_edge_irq+0x77/0x130
<7>[  150.944283]  [<ffffffff81004180>] handle_irq+0x60/0x150
<7>[  150.944293]  [<ffffffff81906406>] ?
atomic_notifier_call_chain+0x16/0x20
<7>[  150.944302]  [<ffffffff8190c38a>] do_IRQ+0x5a/0xe0
<7>[  150.944309]  [<ffffffff8190266f>] common_interrupt+0x6f/0x6f
<7>[  150.944313]  <EOI>  [<ffffffff816a97f5>] ?
cpuidle_wrap_enter+0x55/0xa0
<7>[  150.944327]  [<ffffffff816a97f1>] ? cpuidle_wrap_enter+0x51/0xa0
<7>[  150.944334]  [<ffffffff816a9850>] cpuidle_enter_tk+0x10/0x20
<7>[  150.944341]  [<ffffffff816a940f>] cpuidle_idle_call+0xaf/0x2b0
<7>[  150.944350]  [<ffffffff8100b3aa>] cpu_idle+0xda/0x130
<7>[  150.944360]  [<ffffffff818f081d>] start_secondary+0x266/0x268
<4>[  150.944365] ---[ end trace 32319d39ebee5616 ]---

You can see that it went through hid_ctrl().

From what I can gather using usbmon, the sensor hub sends the feature
report correctly. However, the in-kernel struct is not updated when the report comes in. Therefore, the report from sensor_hub_report() is always zero-filled. When calling sensor_hub_set_feature(), those zeros are being sent back to the device. The feature report contains fields for power state and reporting state. If they are set to zero, the firmware does not know what to do as zero means undefined state. Both power and reporting states have to be set for sensor to report values. Given the zero-filled report, and we can only deal with one field in sensor_hub_set_feature(), setting power state to non-zero also sends zero (i.e. undefined state) to the reporting state field, and vice versa.

Quoted 5 lines

The sensor hub on Acer Iconia W700 is using drivers/hid/hid-sensor-hub.c. I also played with Sony Vaio Duo 11 a while back (before having this patch), and was having trouble turning on gyroscope. I suspect it is caused by the same issue. The sensor hub on Acer is from STMicro, while the one in Vaio Duo is from Freescale.

Just to clarify a little bit on the issue.

Although hid_ctrl() does not care the return value of hid_input_report(), the issue is within hid_input_report(). In drivers/hid/hid-core.c:1317 where raw_event() is called, if return is non-zero, the following call of hid_report_raw_event() is skipped. This call is needed to have the in-kernel struct updated with the actual feature report from device.

Daniel
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Signature · 1 line
Daniel Leung <[email protected]>
#8 lore raw
In reply to Srinivas Pandruvada
Quoted 2 lines · Srinivas Pandruvada

I don't know if this should be fixed in client drivers since other drivers may have this issue.

Agreed.

Srinivas, how about the patch below, could you please test it in your scenario to see whether it actually fixes the issue?

Thanks.

drivers/hid/hid-core.c +1 -1
index 264f550..65879b9 100644
@@ -1293,7 +1293,7 @@ int hid_input_report(struct hid_device *hid, int type, u8 *data, int size, int i
 
 	if (hdrv && hdrv->raw_event && hid_match_report(hid, report)) {
 		ret = hdrv->raw_event(hid, report, data, size);
-		if (ret != 0) {
+		if (ret < 0) {
 			ret = ret < 0 ? ret : 0;
 			goto unlock;
 		}
Signature · 2 lines
Jiri Kosina
SUSE Labs