Skip to contentSkip to conversation

Add support for netconsole driver used on bridge device with VIF attached

PATCH In review Yuval Shaia 3 participants 4 messages May 1, 2013 – May 3, 2013

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Add support for netconsole driver used on bridge device with VIF attached

When starting a VM which has virtual interface attached to the same bridge (i.e vif = [type=netfront,bridge=xenbr0'] in vm.cfg) which is used for netconsole the following message appears (after about 60 seconds) and VM creation operation fails.
Error: Device 0 (vif) could not be connected. Hotplug scripts not working.

Note:
When trying to do the opposite, i.e. first create VM and then run netconsole we got the error #524 - vif2.0 doesn't support polling, aborting.

Here is my network setup:

----------                              ----------
| VM A1  |------vif1.0----->|           | Host B |
|--------|                  |--xenbr0   |        |
| Host A |--bond0 (eth0)--->|           |        |
----------          |                   ----------
                    |                        |
                    V                        V

--------------------------------------------------
| LAN |
--------------------------------------------------

I'm using netconsole to capture logs from Host-A and send them to Host-B. Host-A and Host-B are separate hosts (running XEN) which are connected to the same LAN.
src-ip is Host-A address.
dst-ip/mac is Host-B address.
netconsole parameters: netconsole=1111@src-ip/xenbr0,2002@dst-ip/dst-mac

As i see it, netconsole driver requires ndo_poll_controller from the device's controlling driver (function __netpoll_setup in net/core/netpoll.c), a thing that is not supported currently in xen_netback driver which is the driver that runs on dom0 and serve VM's virtual interface. call flow: init_netconsole() in netconsole.c -> alloc_param_target() -> netpoll_setup()
in netpoll.c -> __netpoll_setup() which check if ndo_poll_controller()
Per Ian,
Are you sure this is being called for the VIF interface? In your
configuration I'd expect it to be called on the bridge not the vif, or
at least for calling on the VIF to not impact whether netpool was
enabled for the bridge or not.

I think the underlying issue which you are seeing is that br_netpoll_setup() requires that all members of the bridge support netpoll before allowing netpoll to be enabled on the bridge itself.

This seems like an odd restriction in the bridge driver since in principal only the port over which the netpoll traffic will be going will need netpoll, but perhaps the bridge can't tell which port that is or is going to be? I think it is worth discussing this with the bridge maintainers (who I have CC'd, threads starts at
http://marc.info/?l=linux-netdev&m=135878868112700&w=2)

Hopefully the bridge isn't flooding/broadcasting netpoll to all ports, at least in the case where DST IP and MAC have been specified. That would be rather inefficient, especially when most ports go to virtual machines.

So before I ack this patch I'd like to hear back from the bridge maintainers about whether the current behaviour in the bridge is intended and whether it could be fixed in some better way than adding netpoll to netback.

AFAICT the only reason to actually support netpoll in netback would be if you wanted host logs to go to a listener running in a domain on the same host, which sounds like a mad idea to me! If someone actually has a real need for that use case and can test that it works I'd be happy to reconsider this patch on that basis (assuming the necessary #ifdefs are added as mentioned before).

Per Ian,
I can see why the *bridge* device might need an ndo_poll_controller hook in this setup but I can't see any reason why the netback device would need one.
Reply:
Please note that without netback driver netconsole runs fine, i.e before trying to create VM which attached to the bridge.

The following patch (to latest kernel) fix this bug by adding implementation to ndo_poll_controller.

0001-Add-support-for-netconsole-driver-used-on-bridge-dev.patch
0 2001
From: Yuval <[email protected]>
Date: Tue, 8 Jan 2013 10:08:45 +0200
Subject: [PATCH] Add support for netconsole driver used on bridge device with
VIF attached

---
 drivers/net/xen-netback/interface.c |    8 ++++++++
 1 file changed, 8 insertions(+)
\ renamed from drivers/net/xen-netback/interface.c +0 -0

b/drivers/net/xen-netback/interface.c index 601ae2a..10751f5 100644

drivers/net/xen-netback/interface.c +0 -0
@@ -179,6 +179,13 @@ static u32 xenvif_fix_features(struct net_device *dev, u32 \

features) return features;
}

+static void xenvif_poll_controller(struct net_device *dev)
+{
+ disable_irq(dev->irq);
+ xenvif_interrupt(dev->irq, dev);
+ enable_irq(dev->irq);
+}
+
static const struct xenvif_stat {
char name[ETH_GSTRING_LEN];
u16 offset;
@@ -237,6 +244,7 @@ static const struct net_device_ops xenvif_netdev_ops = {
.ndo_stop = xenvif_close,
.ndo_change_mtu = xenvif_change_mtu,
.ndo_fix_features = xenvif_fix_features,
+ .ndo_poll_controller = xenvif_poll_controller,
};

struct xenvif *xenvif_alloc(struct device *parent, domid_t domid,

Signature · 1 line
1.7.9.5
#1 lore raw

On Wed, 2013-05-01 at 12:55 +0100, Yuval Shaia wrote:
[... snip regurgitation of the thread...]

Quoted 6 lines

0001-Add-support-for-netconsole-driver-used-on-bridge-dev.patch
0 2001
From: Yuval <[email protected]>
Date: Tue, 8 Jan 2013 10:08:45 +0200
Subject: [PATCH] Add support for netconsole driver used on bridge device with
VIF attached

Sorry, but this is not what I was asking for.

Please submit with a coherent changelog based on (i.e. digested from) the previous discussion which explains why this change is necessary including the background of why it is being made in this way and the interaction with the bridging layer. I wasn't asking you to just cut and paste that discussion and prepend it to the commit like that.

The key point is that we don't think that doing netconsole from dom0 to a domU on the same host is a useful configuration or something which is especially desirable to support but that because of how the bridge handles netconsole netback needs to expose this hook in order that netconsole can be enabled via a physical device on the same bridge to a netserver elsewhere.

Quoted 32 lines
---
 drivers/net/xen-netback/interface.c |    8 ++++++++
 1 file changed, 8 insertions(+)
\ renamed from drivers/net/xen-netback/interface.c +0 -0

b/drivers/net/xen-netback/interface.c index 601ae2a..10751f5 100644

drivers/net/xen-netback/interface.c +8 -0
@@ -179,6 +179,13 @@ static u32 xenvif_fix_features(struct net_device *dev, u32 \
 features)  return features;
 }
 
+static void xenvif_poll_controller(struct net_device *dev)
+{
+	disable_irq(dev->irq);
+	xenvif_interrupt(dev->irq, dev);
+	enable_irq(dev->irq);
+}
+
 static const struct xenvif_stat {
 	char name[ETH_GSTRING_LEN];
 	u16 offset;
@@ -237,6 +244,7 @@ static const struct net_device_ops xenvif_netdev_ops = {
 	.ndo_stop	= xenvif_close,
 	.ndo_change_mtu	= xenvif_change_mtu,
 	.ndo_fix_features = xenvif_fix_features,
+	.ndo_poll_controller = xenvif_poll_controller,
 };
 
 struct xenvif *xenvif_alloc(struct device *parent, domid_t domid,
#2 lore raw
Quoted 17 lines · Ian Campbell

On Wed, 2013-05-01 at 12:55 +0100, Yuval Shaia wrote:
[... snip regurgitation of the thread...]

Quoted 6 lines

0001-Add-support-for-netconsole-driver-used-on-bridge-dev.patch
0 2001
From: Yuval <[email protected]>
Date: Tue, 8 Jan 2013 10:08:45 +0200
Subject: [PATCH] Add support for netconsole driver used on bridge device with
VIF attached

Sorry, but this is not what I was asking for.

Please submit with a coherent changelog based on (i.e. digested from) the previous discussion which explains why this change is necessary including the background of why it is being made in this way and the interaction with the bridging layer. I wasn't asking you to just cut and paste that discussion and prepend it to the commit like that.

Quoted 6 lines

The key point is that we don't think that doing netconsole from dom0 to a domU on the same host is a useful configuration or something which is especially desirable to support but that because of how the bridge handles netconsole netback needs to expose this hook in order that netconsole can be enabled via a physical device on the same bridge to a netserver elsewhere.

I would have thought that doing netconsole on a domU would be a worthwile attempt - especially to troubleshoot a guest?

Quoted 41 lines
Quoted 26 lines
---
 drivers/net/xen-netback/interface.c |    8 ++++++++
 1 file changed, 8 insertions(+)
\ renamed from drivers/net/xen-netback/interface.c +0 -0

b/drivers/net/xen-netback/interface.c index 601ae2a..10751f5 100644

drivers/net/xen-netback/interface.c +7 -0
@@ -179,6 +179,13 @@ static u32 xenvif_fix_features(struct net_device *dev, u32 \
 features)  return features;
 }
 
+static void xenvif_poll_controller(struct net_device *dev)
+{
+	disable_irq(dev->irq);
+	xenvif_interrupt(dev->irq, dev);
+	enable_irq(dev->irq);
+}
+
 static const struct xenvif_stat {
 	char name[ETH_GSTRING_LEN];
 	u16 offset;

drivers/net/xen-netback/interface.c static const struct net_device_ops xenvif_netdev_ops = { · line 250

Quoted 7 lines
drivers/net/xen-netback/interface.c +1 -0
@@ -237,6 +244,7 @@ static const struct net_device_ops xenvif_netdev_ops = {
 	.ndo_stop	= xenvif_close,
 	.ndo_change_mtu	= xenvif_change_mtu,
 	.ndo_fix_features = xenvif_fix_features,
+	.ndo_poll_controller = xenvif_poll_controller,
 };
 
 struct xenvif *xenvif_alloc(struct device *parent, domid_t domid,

_______________________________________________
Xen-devel mailing list
[email protected]
http://lists.xen.org/xen-devel

#3 lore raw
Quoted 25 lines · Konrad Rzeszutek Wilk
Quoted 17 lines · Ian Campbell

On Wed, 2013-05-01 at 12:55 +0100, Yuval Shaia wrote:
[... snip regurgitation of the thread...]

Quoted 6 lines

0001-Add-support-for-netconsole-driver-used-on-bridge-dev.patch
0 2001
From: Yuval <[email protected]>
Date: Tue, 8 Jan 2013 10:08:45 +0200
Subject: [PATCH] Add support for netconsole driver used on bridge device with
VIF attached

Sorry, but this is not what I was asking for.

Please submit with a coherent changelog based on (i.e. digested from) the previous discussion which explains why this change is necessary including the background of why it is being made in this way and the interaction with the bridging layer. I wasn't asking you to just cut and paste that discussion and prepend it to the commit like that.

Quoted 6 lines

The key point is that we don't think that doing netconsole from dom0 to a domU on the same host is a useful configuration or something which is especially desirable to support but that because of how the bridge handles netconsole netback needs to expose this hook in order that netconsole can be enabled via a physical device on the same bridge to a netserver elsewhere.

Quoted 2 lines

I would have thought that doing netconsole on a domU would be a worthwile attempt - especially to troubleshoot a guest?

Yes. But that's not what I said, nor what this patch does.

What this patch enables is dom0 doing netconsole *to* a guest. i.e. dom0's console going to a guest running on the same host, which is not an especially useful thing to do.

AFAIK netfront already supports domU netconsole.

Ian.