Compiling U-BOOT bootloader on x86
I have download and extracted u-boot-1.1.6 on Linux ubuntu. I just want to compile the source code using GCC(not targeting cross compilation for any embedded platform).
I tried running provided MAKEALL makefile but "powerpc-linux-gcc : Not Found" is happening.
My understanding is irrespective of platform the source code should compile.
What are the necessary makefile and environment changes i need to do for compilation on x86?
Dear Ravi Kant Tiwari,
Quoted 3 lines · In message <[email protected]> you wrote:
I have download and extracted u-boot-1.1.6 on Linux ubuntu. I just want to compile the source code using GCC(not targeting cross compilation for any embedded platform).
First: U-Boot 1.1.6 is prehistoric (more than 7 years old). If you intend to do anything with U-Boot, then please use recent code.
Quoted 1 line
My understanding is irrespective of platform the source code should compile.
Your understanding is incomplete / incorrect.
Quoted 2 lines
What are the necessary makefile and environment changes i need to do for compilation on x86?
No changes are needed, but dependingon which exact target board you are compiling for, you will need a cross tool chain for the respective target architecture.
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
No journaling file system can recover your data if the disk dies.
- Steve Rago in <[email protected]>Dear Wolfgang,
Thank you very much . I have taken the *recent code*. Still facing some issues
I have followed following steps to compile it on x86.
1) make clean;
2) make coreboot-x86_config
3) ./MAKEALL -C x86
In step 3 i observed following:
ravitiwari at RAVI-HP-Pavilion-dv2000-GJ175PA-ACJ:~/u-boot-2013.04$ make clean ravitiwari at RAVI-HP-Pavilion-dv2000-GJ175PA-ACJ:~/u-boot-2013.04$ make coreboot-x86_config
Configuring for coreboot-x86 - Board: coreboot, Options:
SYS_TEXT_BASE=0x01110000
ravitiwari at RAVI-HP-Pavilion-dv2000-GJ175PA-ACJ:~/u-boot-2013.04$ ./MAKEALL -C x86
Configuring for coreboot-x86 - Board: coreboot, Options:
SYS_TEXT_BASE=0x01110000
make[1]: *** [interrupts.o] Error 127
make: *** [arch/x86/cpu/libx86.o] Error 2
make[1]: *** [coreboot.o] Error 127
make: *** [arch/x86/cpu/coreboot/libcoreboot.o] Error 2
make[1]: *** [bootm.o] Error 127
make: *** [arch/x86/lib/libx86.o] Error 2
size: './u-boot': No such file/bin/bash: sparse: command not found
make[1]: *** [interrupts.o] Error 127
make: *** [arch/x86/cpu/libx86.o] Error 2
make: *** Waiting for unfinished jobs..../bin/bash: sparse: command not found
make[1]: *** [coreboot.o] Error 127
make: *** [arch/x86/cpu/coreboot/libcoreboot.o] Error 2 /bin/bash: sparse: command not found
make[1]: *** [bootm.o] Error 127
make: *** [arch/x86/lib/libx86.o] Error 2
make: INTERNAL: Exiting with 4 jobserver tokens available; should be 3!
--------------------- SUMMARY ---------------------------- Boards compiled: 1
Boards with errors: 1 ( coreboot-x86 )
----------------------------------------------------------
If at present i am not targeting any embedded platform then why i need *cross tool chain*? x86 tool chain (GCC compiler) is already there in my system.
Regards,
Ravi Tiwari
Quoted 34 lines · Wolfgang Denk
Dear Ravi Kant Tiwari,
Quoted 1 line · In message <[email protected]> you wrote:
I have download and extracted u-boot-1.1.6 on Linux ubuntu. I just want
to
Quoted 2 lines
compile the source code using GCC(not targeting cross compilation for any embedded platform).
First: U-Boot 1.1.6 is prehistoric (more than 7 years old). If you intend to do anything with U-Boot, then please use recent code.
Quoted 1 line
My understanding is irrespective of platform the source code should
compile.
Your understanding is incomplete / incorrect.
Quoted 2 lines
What are the necessary makefile and environment changes i need to do for compilation on x86?
No changes are needed, but dependingon which exact target board you are compiling for, you will need a cross tool chain for the respective target architecture.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de No journaling file system can recover your data if the disk dies.
- Steve Rago in <[email protected]>
Dear ravi tiwari,
Quoted 5 lines · In message <CAEA1ePfrRnUH=reO4nsk3c3S4Sx1oVsVLNSFPqvrWzGXfLzCoA@mail.gmail.com>…
I have followed following steps to compile it on x86.
1) make clean;
2) make coreboot-x86_config
3) ./MAKEALL -C x86
This makes no sense. "MAKEALL" will as first thing run "make mrproper", which makes 1) redundant and undoes 2). If you want to compile for "coreboot-x86", then only "./MAKEALL coreboot-x86" is needed.
Quoted 4 lines
Configuring for coreboot-x86 - Board: coreboot, Options:
SYS_TEXT_BASE=0x01110000
make[1]: *** [interrupts.o] Error 127
make: *** [arch/x86/cpu/libx86.o] Error 2
I recommend to run plain "make" so you can see the actual error messages. Otherwise, check the log files in the LOG directory.
Quoted 1 line
/bin/bash: sparse: command not found
In any case, it seems you should install "sparse".
Quoted 1 line · Wolfgang Denk
And please: don't top post / full quote.
Best regards,
Wolfgang Denk
Signature · 6 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
He'd heard her use that sweet, innocent tone of voice before. It
meant that, pretty soon, there was going to be trouble.
- Terry Pratchett, _Truckers_